Pelco Automobile Electronics C2924M 4 05 User Manual

I N S T A L L A T I O N / O P E R A T I O N  
CCC1390H Series  
Camera  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
C2924M (4/05)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of Illustrations  
List of Tables  
C2924M (4/05)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regulatory Notices  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful  
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio  
communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet  
is available from the U.S. Government Printing Office, Washington D.C. 20402.  
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this  
equipment under Federal Communications Commission’s rules.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
Warnings  
To avoid damaging your camera, please note the following:  
1. The camera has threaded mounting locations on the top and bottom of the case. Use only a standard photographic mounting bolt with a  
1/4-20 UNC thread.  
2. Do not touch the surface of the optical filter. If the filter is dusty or is accidentally touched, use clean, compressed air or lens cleaning paper  
to clean it.  
3. Do not expose the camera imager to direct sunlight as this may impair camera performance. Always keep the lens mount cap in place until  
you install the lens.  
4. Do not use this camera outdoors without an appropriate enclosure. Do not install near flammable gas or corrosive chemical fumes.  
5. Use a soft dry cloth to clean the camera case. If necessary, use a soft cloth moistened with a neutral detergent diluted with water; then dry  
with the dry cloth. Never use alcohol, benzene, or other volatile solutions.  
6
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Description  
The CCC1390H Series camera is a compact, wide dynamic range (WDR), day/night camera. Its WDR technology provides up to 60 dB of dynamic  
range and produces superior images over a wide range of lighting conditions, including extreme backlight conditions. The camera also uses a  
removable infrared (IR) cut filter to switch between color and black-white (B-W) modes as environmental lighting conditions change. It also pro-  
vides a dual resolution of 530 TVL (B-W) and 480 TVL (color).  
On-screen programmable menus can be accessed locally using the rear panel button or remotely using any Pelco controller with Pelco P or Pelco D  
protocol. Use these menus to select a specific profile or to customize and save camera settings for the specific application.  
The CCC1390H Series camera has a standard CS-mount and can be used with fixed, manual, or DC-drive auto iris lenses. The auto iris is controlled  
through a standard four-pin square connector that is included with all Pelco auto iris lenses.  
The CCC1390H Series camera is quick and easy to install and is ideal for Pelco’s DomePak® and ImagePak® fixed camera dome/enclosure  
packages.  
PRODUCT FEATURES  
Compact Body Style  
Wide Dynamic Range (60 dB Maximum); Captures Both High-Luminance and Low-Luminance Objects  
Day/Night with Automatic or Manual Control; Captures High-Quality Color During the Day and Clear B-W Images at Night  
Electronic Zoom  
1/3-Inch Format Sony® SS-2WD CCD Imager  
Digital Signal Processing  
530 TV Lines (B-W); 480 TV Lines (Color)  
On-Screen Menu Configuration  
Four Preset Application Profiles; One User-Definable Profile  
Selectable Auto White Balance (AWB), Automatic Gain Control (AGC), Electronic Shutter Control (ESC), and Backlight Compensation (BLC)  
Digital Slow Shutter (DSS)  
Flickerless Mode  
CS Lens Mount (C-Mount Lens Requires Optional Adapter)  
Autosensing DC-Drive Auto Iris  
Autosensing 24 VAC/12 VDC with Line Lock or Internal Synchronization  
Internal Top/Bottom Mount  
C2924M (4/05)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
3
3a  
ᕤ ᕥ  
ᕡ ᕢ  
ᕩ ᕫᕾ  
Figure 1. CCC1390H Series Camera  
Lens Mount: Mount a standard CS-mount lens to the CCC1390H Series camera (refer to Lens Mounting). To use a C-mount lens, install a  
C/CS-mount adapter.  
Back Focus Locking Screw: Use a 1.5-mm Allen wrench to adjust the back focus (refer to Lens Focusing).  
Camera Mount and 3a Mount Adapter: Use the top or bottom mount hole. The maximum thread depth (top) is 0.188 inches (4.7 mm); the  
adapter extends the thread depth (top) to 0.25 inches (6.4 mm). The maximum thread depth (bottom) is 0.25 inches (6.4 mm). Refer to Camera  
Mounting.  
Serial Terminating Switch: Use this switch to terminate the serial signal at the last camera on the serial chain (refer to Connecting  
External Control).  
Auto Iris Lens Connector: Insert the four-pin connector from the DC-drive auto iris lens into this connector (refer to Lens Mounting).  
Video Output Connector: Connect a coaxial video cable to this BNC connector to output the video image (refer to Connecting Video).  
Setup Button: Use this five-position button to configure the camera either directly (refer to Quick Setup) or through the setup menus (refer  
to Accessing Setup Menus).  
Power Terminal Strip: Use this three-pin, push-in type terminal strip to connect either 12 VDC or 24 VAC power (refer to Connecting  
Power).  
Indicators: Use these indicators to quickly determine camera status (refer to Quick Setup).  
ᕫᕾ External Control Connector: Use this seven-pin connector to connect the camera to one or more serial devices. Use it also to connect an  
external day/night filter switch. Refer to Connecting External Control for more information.  
MODELS  
CCC1390H-6  
CCC1390H-6X  
1/3-inch high resolution day/night, WDR, CCD camera, 24 VAC or 12 VDC, NTSC format  
1/3-inch high resolution day/night, WDR, CCD camera, 24 VAC or 12 VDC, PAL format  
8
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
PARTS LIST  
CCC1390H Series camera  
Quick Start Guide  
Safety Instructions  
External control connector assembly: seven-pin micro (1.25 mm) connector with wires (26 AWG) and connector cover  
Camera mount spacer  
Four-pin auto iris connector (type DN-152N)  
Lens mount cap  
Resource CD:  
Installation/Operation manual: INSTALL.PDF  
Quick Start Guide: QSG.PDF  
Important Safety Instructions: SAFETY.PDF  
OPTIONAL ACCESSORIES  
PCMA40  
Lens adapter. Adapts standard C-mount lenses to CS-mount cameras.  
REQUIRED TOOLS  
Small Phillips screwdriver for connector cover  
Small flat tip screwdriver for serial termination  
Allen wrench (1.5 mm) for back focus adjustment  
Neutral density filter (ND3) for auto iris adjustment  
C2924M (4/05)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Lens Mounting  
The CCC1390H Series camera supports both manual and DC-drive auto iris lenses, either fixed focal length or varifocal. It automatically senses an  
auto iris lens as soon as you plug in the connector. The camera has a standard CS-mount that can accept a C-mount lens with a PCMA40 lens  
adapter.  
After mounting an auto iris lens, but before using the camera, perform the auto iris automatic adjustment procedure (refer to Auto Iris Lens  
Adjustment). Also perform this procedure each time you change the lens.  
NOTE: The CCC1390H Series camera does not support video-drive auto iris lenses.  
WIRING AN AUTO IRIS LENS  
DC-drive auto iris lenses are controlled through the four-pin drive connector (type D4-152N). Figure 2 identifies the pin connections for the auto iris  
lens connector on the back of the camera.  
2
1
Pin DC-Drive Auto Iris Lens  
1
2
3
4
Control coil negative (–)  
Control coil positive (+)  
Drive coil positive (+)  
Drive coil negative (–)  
4
3
Figure 2. DC-Drive Auto Iris Lens Connector  
10  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
MOUNTING THE LENS  
1. Make sure the lens will not touch the camera imager when installed.  
2. Use clean, compressed air or a clean, dry lens cloth to make sure there is no dust or other foreign matter between the lens and the camera  
imager.  
3. C-mount lens: Screw the adapter onto the lens.  
4. Screw the lens onto the lens mount.  
5. DC-drive auto iris lens: Connect the four-pin connector from the lens to the connector on the back of the camera.  
CS-MOUNT  
LENS  
C/CS MOUNT ADAPTER  
(FOR C-MOUNT LENS ONLY)  
AUTO IRIS  
LENS CABLE  
AND CONNECTOR  
(OPTIONAL)  
Figure 3. Mounting Lens to Camera  
C2924M (4/05)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Camera Mounting  
The CCC1390H Series camera can be mounted from either the top or bottom, depending on the type of camera mount used in your installation. Use  
a standard 1/4-20 screw. The maximum thread depth (top) is 0.188 inches (4.7 mm). To extend the thread depth (top) to 0.25 inches (6.4 mm), use  
the camera mount spacer (supplied). The maximum thread depth (bottom) is 0.25 inches (6.4 mm).  
The CCC1390H Series camera can be fitted with most Pelco lenses and mounted into most Pelco domes and enclosures, resulting in the greatest  
possible number of combinations. This means you can find a solution for nearly any application.  
When selecting a lens, dome, or enclosure for this camera, consider how the physical dimensions of each component may affect camera  
installation and operation. Specifically, you should address the following three issues.  
Enclosure size: The camera dimensions are 2.2 (D) x 2.09 (W) x 2.17 (H) inches (5.6 x 5.3 x 5.5 cm). Make sure the enclosure is large  
enough for both the camera and the lens.  
Lens size: Some lenses have minimum and maximum lengths. To focus the scene correctly, you may have to adjust the lens to its maximum  
length. This could affect how it fits within the enclosure.  
Optical alignment: The optical center of this camera may be too low for some enclosures. As a result, the lower portion of the scene may  
be obstructed by the enclosure itself. The camera sled in many Pelco enclosures has a low side and a high side. You may be able to raise  
the optical center by flipping the camera sled to the high side.  
NOTE: To simplify lens and enclosure selection, Pelco offers ImagePak options for the CCC1390H Series camera. Select the lens and the dome or  
enclosure. Pelco will build and test it for you. Contact Pelco or your dealer for more information.  
12  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Connecting Power, Video, and Control  
The CCC1390H Series camera offers standard power and coax video connectors as well as an external control connector. Before installation,  
identify how you will connect each power, video, and control lead to the camera.  
CONNECTING POWER  
The CCC1390H Series camera is designed to operate from either a 12 VDC or a 24 VAC power source. The camera automatically senses power  
type. Use only a Class 2 isolated power source that can supply 12 VDC 15% or 24 VAC 15%, 50/60 Hz. Maximum power consumption is about  
3.5 watts.  
WARNINGS:  
Do not connect high voltage power to the camera because you may damage the camera.  
Do not short circuit the power leads when connecting the power supply to the camera.  
Do not remove the connector cover during camera operation.  
NOTES:  
Be sure to use 60 Hz power for NTSC (CCC1390H-6) and 50 Hz power for PAL (CCC1390H-6X).  
Install the camera near a socket or outlet that is easily accessible.  
These maximum distances are based on a maximum allowable voltage drop of 10%.  
Table A. Recommended Wire Gauge and Maximum Wiring Distances  
Maximum Distance  
Wire Gauge  
12 VDC  
24 VAC  
24 AWG (0.25 mm2)  
22 AWG (0.35 mm2)  
20 AWG (0.5 mm2)  
18 AWG (1.0 mm2)  
16 AWG (1.5 mm2)  
14 AWG (2.5 mm2)  
12 AWG (4.0 mm2)  
10 AWG (6.0 mm2)  
373 ft (113 m)  
224 ft (68 m)  
594 ft (181 m)  
356 ft (108 m)  
567 ft (172 m)  
902 ft (372 m)  
1,432 ft (436 m)  
2,285 ft (696 m)  
3,622 ft (1,103 m)  
5,760 ft (1,755 m)  
945 ft (288 m)  
1,504 ft (458 m)  
2,388 ft (727 m)  
3,809 ft (1,160 m)  
6,037 ft (1,840 m)  
9,600 ft (2,926 m)  
C2924M (4/05)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
CONNECTING AC POWER  
The CCC1390H Series camera requires a power supply of 24 VAC 15% (20.4 to 27.6 VAC), 50/60Hz. Make sure the power supply has a minimum  
rating of 270 mA.  
When connecting more than one camera to the same AC transformer, remember the following:  
Connect the same side of the transformer to the same terminal on all cameras. Otherwise, the cameras may be out of phase, causing a  
vertical roll when switching between cameras. Refer to Camera Synchronization for more information.  
Use a transformer whose rated power supply is greater than 270 mA multiplied by the number of cameras.  
To connect AC power:  
1. Strip at least 0.4 inches (10 mm) of the insulation from each power wire.  
2. Press and hold the button over either hole marked 24 VAC.  
3. Insert one wire from the power supply into the hole and release the button.  
4. Gently pull the wire to make sure it is secure.  
5. Repeat steps 2 through 4 for the second wire from the power supply.  
6. If you are using a ground wire, repeat steps 2 through 4, inserting the ground wire into the hole marked GND.  
POWER SUPPLY  
INPUT  
BUTTONS  
24 VAC  
OUTPUT  
Figure 4. Connecting AC Power  
14  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
CONNECTING DC POWER  
The CCC1390H Series camera requires a power supply of 12 VDC 15% (10.2 to 13.8 VDC). Make sure the power supply has a minimum rating of  
390 mA.  
WARNINGS:  
For safety, include a 1.0 A slow blow fuse when connecting DC power, as shown in Figure 5.  
The DC power supply must be UL- and CE-certified.  
Make sure you wire the power polarity correctly.  
To connect DC power:  
1. Strip at least 0.4 inches (10 mm) of the insulation from each power wire.  
2. Press and hold the button over the hole marked (–).  
3. Insert the negative wire from the power supply into the hole and release the button.  
4. Gently pull the wire to make sure it is secure.  
5. Repeat steps 2 through 4 for the positive wire from the power supply. Use the hole marked (+). For safety, add a 1.0 A slow blow fuse to the  
positive wire from the power supply. The fuse should be less than 4 inches (10 cm) from the positive terminal on the power supply.  
BUTTONS  
4 INCH (10 CM) MAX.  
POWER  
SUPPLY  
INPUT  
+12  
VDC  
1.0 A FUSE  
(SLOW BLOW)  
GND  
Figure 5. Connecting DC Power  
CONNECTING VIDEO  
Table B. Video Coaxial Cable Requirements  
Cable Type*  
RG59/U  
Maximum Distance  
750 ft (229 m)  
RG6/U  
1,000 ft (305 m)  
1,500 ft (457 m)  
RG11/U  
*Cable requirements:  
75 ohms impedance  
All-copper center conductor; steel-center conductor cable may result in poor performance  
All-copper braided shield with 95% braid coverage  
If white spots appear in the video image, one or more pixels on the camera imager may be defective. This condition is common to CCD camera  
imagers. To correct this condition, refer to Pixel Correction.  
C2924M (4/05)  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
CONNECTING EXTERNAL CONTROL  
The external control connector on the rear panel lets you remotely access and control the CCC1390H Series camera. The external control  
connector assembly is a seven-pin micro (1.25 mm) connector with wires (26 AWG) and connector cover.  
You can access and configure the menu settings from any Pelco keyboard, receiver, or other device that supports the Pelco D or Pelco P protocol.  
The camera supports the following settings:  
Baud rate:  
Start bit:  
Data bits:  
Stop bit:  
Parity:  
2400, 4800, 9600, 19200  
1
8
1
None  
You can also control day/night filter operation from an external switch.  
Pin  
1
Lead  
Color  
Red  
Pelco Data RX+  
Pelco Data RX–  
Ground  
2
White  
Black  
Red  
REMOVE  
CONNECTOR  
COVER  
3
4
Pelco Data TX+  
Pelco Data TX–  
Ground  
5
White  
Black  
Brown  
6
INSTALL  
CONNECTOR  
COVER  
7
Day/Night Control Signal Input  
PIN 1  
PIN 7  
TO CONTROL  
DEVICE  
RX+  
RX-  
GND  
Figure 6. Installing the External Control Connector  
16  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
CONNECTING SERIAL CONTROL (PELCO D/PELCO P)  
1. Turn off power to the camera.  
3. If necessary, plug the external control connector assembly (supplied) into the camera. Then use a small Phillips screwdriver to secure the  
assembly connector cover to the rear panel.  
4. Use 100-ohm twisted pair cabling to wire each pair on the enclosed connector assembly. The decision to use shielded cable depends on  
your installation; shielded cable may be optional.  
TERM = OFF  
TERM = OFF  
PIN 1  
PIN 1  
PIN 7  
PIN 7  
RX+ (1)  
RX- (2)  
GND (3)  
GND (6) TO (3)  
TX- (5) TO RX- (2)  
TX+ (4) TO RX+ (1)  
TERM = ON  
PIN 7  
PIN 1  
TX+ (4) TO RX+ (1)  
TX- (5) TO RX- (2)  
GND (6) TO (3)  
Figure 7. Configuring a Serial Chain  
5. Wire the camera to the control device as follows:  
Pin 1 (red, RX+) to the TX+ lead on the control device.  
Pin 2 (white, RX–) to the TX– lead on the control device.  
Pin 3 (black, ground) to the ground lead on the control device.  
Shielded cable only: Connect the shield to either pin 3 (black, ground) or pin 6 (black, ground).  
6. To connect additional cameras in a serial chain:  
a. Use a small flat tip screwdriver to turn the termination switch on this camera to OFF. The default position is ON.  
b. Wire this camera to the next camera as follows:  
Pin 4 (red, TX+) to pin 1 (red, RX+) on the next camera.  
Pin 5 (white, TX–) to pin 2 (white, RX–) on the next camera.  
Pin 6 (black, ground) to pin 3 (black, ground) on the next camera.  
Shielded cable only: Connect the shield to either pin 3 (black, ground) or pin 6 (black, ground).  
C2924M (4/05)  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7. If you are not connecting additional cameras, or after adding all cameras to the chain, make sure you set the termination switch to ON for  
the last camera in the chain.  
8. Access the CAMERA SETUP menu to set the following (refer to Camera Setup):  
Set a unique ADDRESS for each camera on the serial chain.  
Set the communication rate (COM SPEED) to match the rate of each camera on the serial chain.  
Table C. Camera/Controller Settings for KBD200A/KBD300A (Direct Mode)  
Equipment  
Parameter  
ADDRESS  
PELCO D  
1-30  
PELCO P  
1-30  
Camera  
COM SPEED  
ADDRESS  
2400  
4800  
Keyboard  
1-30  
2-31*  
DIP SWITCH  
ON: 5, 7  
ON: 5  
OFF: all others  
OFF: all others  
*To select the camera using the Pelco P protocol, add one to the camera number at the controller. For example, if the ADDRESS at the camera is  
set to 10, select camera 11 at the controller.  
CONNECTING DAY/NIGHT FILTER CONTROL  
In some installations, high infrared (IR) illumination or other light sources may interfere with the camera’s automatic day/night mode operation.  
Use an external day/night filter switch, such as a photosensor, to keep the camera from constantly switching filters.  
Table D. Day/Night Control Signal  
Signal  
Voltage  
D/N Mode  
AUTO  
Open or High  
Short or Low  
3.0V to 3.3V  
-0.3V to 0.3V  
BW  
NOTES:  
Do not exceed these values.  
The CCC1390H Series camera responds only to the input signal from the switch. It does not provide enough power to drive an external  
device.  
1. Turn off power to the camera.  
3. If necessary, plug the external control connector assembly (supplied) into the camera. Then use a small Phillips screwdriver to secure the  
assembly cover to the rear panel.  
18  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
4. Use 100-ohm twisted pair cabling to wire the device to the enclosed connector assembly. The decision to use shielded cable depends on  
your installation; shielded cable may be optional.  
EXTERNAL SWITCH  
PIN 1  
PIN 7  
INPUT (7)  
GND (6)  
Figure 8. Day/Night Filter Control Configuration  
5. Wire the camera to the external switch as follows:  
Pin 7 (brown, signal input) to the (+) lead on the external switch.  
Pin 6 (black, ground) to the (–) lead on the external switch.  
Shielded cable only: Connect the shield to either pin 3 (black, ground) or pin 6 (black, ground).  
6. Change DAY & NIGHT to EXT. (external) on the EXPOSURE SETTINGS menu.  
7. Configure the external switch as follows:  
Open or High: Camera operates in AUTO mode.  
Short or Low: Camera operates in BW mode.  
C2924M (4/05)  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Quick Setup  
Several CCC1390H Series camera settings can be changed directly from the rear panel button. When a rear panel indicator is lit, the correspond-  
ing option is enabled. You can change the following options directly from the rear panel:  
AGC  
Press the button up to enable or disable automatic gain control (AGC). Refer to Automatic Gain Control (AGC) for more  
information.  
D/N  
Press the button left to enable or disable day and night mode. When enabled, the AUTO mode is selected. When disabled, the  
COLOR mode is selected. Refer to Day and Night for more information.  
You cannot change day and night mode when AGC is disabled; the camera uses the COLOR mode.  
SENS  
WD  
Press the button down to enable or disable DSS (SENS). Refer to Digital Slow Shutter (DSS (SENS)) for more information.  
If you disable SENS on the rear panel, the camera saves the DSS (SENS) value on the EXPOSURE SETTING menu.  
Press the button right to change the auto exposure mode. When this indicator is lit, WDR is selected. Otherwise, the NORMAL  
auto exposure mode is selected. Refer to Auto Exposure for more information.  
NOTES:  
To enable the rear panel indicators, the LED setting on the CAMERA SETUP menu must be set to ON (the default).  
To enable the quick setup feature, the SWITCH setting on the CAMERA SETUP menu must be set to ON (the default).  
AGC  
WD  
SENS  
D/N  
Figure 9. Quick Setup Indicators and Presses  
20  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Accessing Setup Menus  
NAVIGATING SETUP MENUS FROM THE REAR PANEL  
UP  
SELECT  
RIGHT  
DOWN  
LEFT  
Figure 10. Rear Panel Indicators and Presses  
Table E. Rear Panel Buttons and Actions  
MENU ACTION  
BUTTON ACTION  
Long center press  
Up or down press  
Right or left press  
Short center press  
Short center press  
Enter setup menus.  
Move up or down in menu or item options.  
Move right or left in menu.  
Select menu or item.  
Save setting and exit to menu.  
To display a menu:  
1. Press and hold the button for two seconds to open the MAIN MENU. The four indicators on the rear panel blink until you close the setup  
menu.  
2. Press the button up or down to select a menu.  
3. Press the center of the button to open the menu.  
To change a setting:  
1. Press the button up or down to select the item.  
2. Press the center of the button to open the item.  
3. Press the button up or down to move through the options.  
4. Press the center of the button to save the setting and return to the menu.  
To move to a previous menu, select BACK and press the center of the button.  
To close the setup menus, select EXIT from any menu and press the center of the button.  
NOTES:  
When you select BACK or EXIT on any menu, the camera saves the current settings into memory.  
The menu closes automatically after three minutes of inactivity.  
C2924M (4/05)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
NAVIGATING SETUP MENUS FROM A PELCO CONTROLLER  
USING PRESET 95 TO ACCESS SETUP MENUS  
You can use preset 95 to access and navigate the setup menus from various Pelco controllers. Use the instructions for your controller to access  
the main menu.  
CM6700/CM6800  
1. Enter the camera number and press the CAM key.  
2. Enter 95 and hold the PRESET key for two seconds. A menu screen appears.  
3. Move the joystick down to highlight SET.  
4. Move the joystick right. The MAIN MENU appears.  
KBD200A/KBD300A (Direct Mode)  
1. Enter the camera number and press the CAM key.  
2. Enter 95.  
3. Press the PRESET key. The MAIN MENU appears.  
CM9500  
1. Enter the camera number and press the CAM key. The Main menu appears.  
2. Highlight SETUP in the Main menu and press the SELECT key.  
3. Highlight CAM in the Setup menu and press the SELECT key.  
4. Highlight PRESET in the Camera menu and press the SELECT key.  
5. Enter 95 and press the F1 key. The MAIN MENU appears.  
CM9740/CM9760/CM9770/CM9780  
1. Press the ESCAPE key to open the Main menu. Select DEF. The Define Submenu appears.  
2. Enter your four-digit PIN if this is your first time entering this mode.  
3. Enter 95 and select PRST. The MAIN MENU appears on the monitor.  
4. Select the Quit icon to return to the default menu.  
MPT9500 (RS-485 Mode)  
1. Enter 95 and press the PRESET SET key.  
2. Press the F2 key. The MAIN MENU appears.  
PelcoNet™  
1. Check the Set box.  
2. Click the preset 95 button. The MAIN MENU appears.  
22  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
NAVIGATING SETUP MENUS  
actions for menu navigation.  
Table F. Pelco Controller Buttons and Actions  
MENU ACTION  
BUTTON ACTION  
Move up or down in menu or item options.  
Move right or left in menu.  
Select menu or item.  
Move joystick up or down.  
Move joystick right or left.  
Press the iris open button.  
Press the iris open button.  
Save setting and exit to menu.  
NOTE: If your Pelco controller does not have a joystick, use the up, down, right, and left buttons.  
To display a menu:  
1. Use the joystick to select a menu.  
2. Press the iris open button to open the menu.  
To change a setting:  
1. Use the joystick to select the item.  
2. Press the iris open button to open the item.  
3. Move the joystick up or down to move through the options.  
4. Press the iris open button to save the setting and return to the menu.  
To move to a previous menu, select BACK and press the iris open button.  
To close the setup menus, select EXIT from any menu and press the iris open button.  
NOTES:  
When you select BACK or EXIT on any menu, the camera saves the current settings into memory.  
The menu closes automatically after three minutes of inactivity.  
commands.  
C2924M (4/05)  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Setup Menus  
The CCC1390H Series camera uses setup menus instead of hardware switches for configuring the camera. As a result, you have more options for  
customizing the camera for its specific application.  
NOTES:  
After you customize any aspect of the CCC1390H Series camera, be sure to save your custom settings. (Refer to Profiles for information  
about saving custom settings.)  
Menu items that cannot be changed are either disabled or marked with an asterisk (*).  
FLICKERLESS changes to SHUTTER SPEED when AUTO EXPOSURE mode is set to MANUAL.  
The setup menu tree is represented on this and the next page:  
AI AUTO ADJUSTMENT  
OK  
MAIN MENU  
PROFILES  
EXPOSURE SETTINGS  
FUNCTION SETTINGS  
CAMERA SETUP  
AI AUTO ADJUSTMENT  
PIXEL CORRECTION  
SYSTEM INFORMATION  
PROFILES  
>
>
>
>
>
>
>
ACTIVE  
SAVE AS  
*DEFAULT  
> STANDARD  
> CUSTOM  
STANDARD  
CANCEL  
PIXEL CORRECTION  
COVER THE LENS  
AND SELECT OK  
EXIT  
BACK  
EXIT  
OK  
CANCEL  
EXPOSURE SETTINGS  
AUTO EXPOSURE  
VIDEO LEVEL  
FLICKERLESS  
AGC  
> NORMAL  
SYSTEM INFORMATION  
> 0  
> OFF  
> ON  
> 4  
FIRMWARE VERSION  
OSD VERSION  
1.0  
1.0  
DSS(SENS)  
DAY & NIGHT  
D&N DETECTION  
D&N FILTER LIMIT  
BACK  
> COLOR  
>
RESTORE FACTORY SETTINGS  
>
>
EXIT  
BACK  
EXIT  
RESTORE FACTORY SETTINGS  
FUNCTION SETTINGS  
LINE SYNC  
WHITE BALANCE  
MANUAL RED/BLUE  
GAMMA  
SHARPNESS  
E-ZOOM  
MASKING  
TITLE  
BACK  
>
OK  
CANCEL  
> AUTO  
>
> 60%(NORM)  
>
>
>
>
EXIT  
CAMERA SETUP  
ADDRESS  
COM SPEED  
LED  
> 1  
> 4800  
> ON  
> ON  
SWITCH  
BACK  
EXIT  
24  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
V-PHASE ADJ  
LINE SYNC  
LINE SYNC  
PHASE VALUE = 45  
> AUTO  
>
V-PHASE ADJ  
BACK  
EXIT  
MANUAL RED/BLUE  
RED GAIN  
BLUE GAIN  
RED HUE  
> -1  
> -2  
> 1  
BLUE HUE  
> 1  
BACK  
EXIT  
SHARPNESS  
APERTURE GAIN  
> -1  
BACK  
EXIT  
E-ZOOM  
POSITION  
ZOOM  
POSITION  
> OFF  
>
BACK  
EXIT  
MASKING  
MASK SETTING  
MASK  
MASK EDIT  
MASK ERASE  
> OFF  
>
BACK  
EXIT  
EDIT TITLE  
TITLE  
ABCDEFGHIJKLM  
NOPQRSTUVWXYZ  
abcdefghijklm  
TITLE  
EDIT TITLE  
> OFF  
>
nopqrstuvwxyz  
0123456789-/  
BACK  
EXIT  
BACK  
BS  
_________________  
C2924M (4/05)  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAIN MENU  
The following sections describe each menu and all settings associated with that menu.  
The sample screens in each section show the default settings.  
MAIN MENU  
PROFILES  
>
>
>
>
>
>
>
EXPOSURE SETTINGS  
FUNCTION SETTINGS  
CAMERA SETUP  
AI AUTO ADJUSTMENT  
PIXEL CORRECTION  
SYSTEM INFORMATION  
To display the MAIN MENU:  
Press and hold the center of the button on the rear panel. Refer to Navigating Setup  
Menus from the Rear Panel.  
Use the Pelco controller. Refer to Navigating Setup Menus from a Pelco Controller.  
EXIT  
Profiles  
Select this option to access the camera profile settings (refer to Profiles).  
Exposure Settings  
Select this option to configure the exposure settings (refer to Exposure Settings).  
Function Settings  
Select this option to configure the function settings (refer to Function Settings).  
Camera Setup  
Select this option to configure the communication settings for the camera (refer to Camera Setup).  
AI Auto Adjustment  
Select this option to perform the auto iris lens automatic adjustment procedure (refer to Auto Iris Lens Adjustment).  
Pixel Correction  
Select this option to perform the automatic pixel correction procedure (refer to Pixel Correction).  
System Information  
Select this option to display the camera firmware information or to restore the factory default settings (refer to System Information).  
PROFILES  
Use this option to select a profile or save custom settings. Use profiles for faster installation or to  
adjust camera settings quickly for changing light conditions. The default is STANDARD.  
PROFILES  
ACTIVE  
SAVE AS  
*DEFAULT  
> STANDARD  
> CUSTOM  
STANDARD  
The CCC1390H Series camera offers four predefined profiles and one custom, or user-definable,  
profile. You cannot modify predefined profiles.  
ACTIVE  
BACK  
EXIT  
Select one of the following application profiles:  
STANDARD Select this profile for most scenes. This is the default.  
DAY&NIGHT Select this profile if the camera is located outside a building or in certain indoor low-light applications. When selected, the  
camera adjusts its settings to account for light level changes. Examples include parking lots and walkways.  
WDR  
Select this profile if light from an exterior window or door in the camera view causes an object or person to be backlit or  
silhouetted.  
GAMING  
Select this profile if the camera scene is illuminated by mixed interior lighting and includes self-illuminated devices. Examples  
include arcades with gaming machines with bright, flashing lights.  
CUSTOM  
<HOLD>  
Select this profile to activate your saved camera settings.  
Whenever you open the setup menus, the current camera settings are copied into the <HOLD> profile. As you change camera  
settings, the camera stores these new settings into this profile. This lets you experiment with new settings without erasing the  
CUSTOM profile. When you perform a SAVE AS, the camera saves the <HOLD> profile settings to the CUSTOM profile (refer to  
Save As).  
26  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Table G. Settings by Profile  
Profile  
STANDARD (default)  
DAY&NIGHT  
WDR  
GAMING  
Exposure Settings  
AUTO EXPOSURE  
VIDEO LEVEL  
FLICKERLESS  
AGC  
NORMAL  
NORMAL  
WDR  
0
NORMAL  
0
OFF  
ON  
0
OFF  
0
OFF  
ON  
OFF  
ON  
ON  
DSS  
4
OFF  
4
4
DAY & NIGHT  
D&N DETECTION  
D&N FILTER LIMIT  
COLOR  
AUTO  
COLOR  
COLOR  
5 SEC  
10 MIN  
Function Settings  
AUTO  
LINE SYNC  
AUTO  
AUTO  
AUTO  
AUTO  
INTERNAL  
INDOOR  
DEFAULT  
45%  
WHITE BALANCE  
MANUAL RED/BLUE  
GAMMA  
AUTO  
DEFAULT  
60% (NORM)  
-1  
DEFAULT  
60% (NORM)  
-1  
DEFAULT  
SHARPNESS  
E-ZOOM  
-1  
-1  
OFF  
OFF  
OFF  
OFF  
STANDARD  
DAY & NIGHT  
WDR  
GAMING  
Figure 11. Sample Profile Scenes  
SAVE AS  
Use this option to save all settings from the <HOLD> profile into the CUSTOM profile. After selecting this option, the ACTIVE profile changes to  
CUSTOM.  
C2924M (4/05)  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
EXPOSURE SETTINGS  
Select this option to configure the exposure settings for the CCC1390H Series camera. The default EXPOSURE SETTINGS menu appears when  
AUTO EXPOSURE is set to NORMAL, BLC, or WDR. When AUTO EXPOSURE is set to MANUAL, the FLICKERLESS option is replaced with the  
SHUTTER SPEED option.  
EXPOSURE SETTINGS  
EXPOSURE SETTINGS  
AUTO EXPOSURE  
VIDEO LEVEL  
FLICKERLESS  
AGC  
> NORMAL  
AUTO EXPOSURE  
VIDEO LEVEL  
SHUTTER SPEED  
AGC  
> MANUAL  
> 0  
> 0  
> OFF  
> ON  
> 4  
> 1/60  
> ON  
> 4  
DSS(SENS)  
DSS(SENS)  
DAY & NIGHT  
D&N DETECTION  
D&N FILTER LIMIT  
BACK  
> COLOR  
>
DAY & NIGHT  
D&N DETECTION  
D&N FILTER LIMIT  
BACK  
> COLOR  
>
>
>
EXIT  
EXIT  
NORMAL, BLC, or WDR  
AUTO EXPOSURE  
MANUAL  
AUTO EXPOSURE  
AUTO EXPOSURE  
The automatic exposure feature automatically adjusts the electronic shutter and mechanical iris to set the correct exposure. Select one of the  
following automatic exposure modes:  
NORMAL  
Select this mode to use the electronic shutter and mechanical iris to control exposure. As lighting conditions change, the camera  
adjusts exposure based on input from the electronic shutter.  
BLC  
Select this mode for scenes that are strongly backlit. The camera corrects the image to bring out the detail of the subject, such  
as a person entering a building through a door.  
MANUAL  
WDR  
Select this mode to set the electronic shutter speed manually (refer to Shutter Speed for more information).  
Select this mode for scenes that include both high-light and low-light objects.  
NOTES:  
You can also use the rear panel button to switch between NORMAL and WDR modes (refer to Quick Setup).  
When you select BLC, the VIDEO LEVEL option is disabled.  
When you select MANUAL, the FLICKERLESS option changes to SHUTTER SPEED. Also, the DSS(SENS) option is disabled.  
When you select WDR, the GAMMA and E-ZOOM options are disabled.  
VIDEO LEVEL  
Use this option to set the video output voltage from 0.9 Vp-p to 1.1 Vp-p in increments of 0.02 Vp-p. Use it to compensate for signal loss due to  
long cable runs. You can also use it to boost the video output.  
Select a value between -5 (0.9 Vp-p) and 5 (1.1 Vp-p). The default is 0 (1.0 Vp-p).  
NOTE: When AUTO EXPOSURE is set to BLC, you cannot adjust the video level.  
FLICKERLESS  
In some installations, the cycle of the fluorescent lights may interfere with the electronic iris shutter speed. Use this option to override the shutter  
speed. When enabled, the shutter speed is set to 1/100 (NTSC) or 1/120 (PAL).  
Select ON or OFF. The default is OFF.  
NOTE: This option appears when AUTO EXPOSURE is set to NORMAL, BLC, or WDR.  
28  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
SHUTTER SPEED  
Use this option to set the shutter speed manually.  
Select one of the following options: 1/60(NTSC), 1/50(PAL), 1/100(NTSC), 1/120(PAL), 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/20000,  
1/50000. The default is 1/60(NTSC) or 1/50(PAL).  
NOTE: This option appears when AUTO EXPOSURE is set to MANUAL.  
AUTOMATIC GAIN CONTROL (AGC)  
Automatic gain control (AGC) automatically adjusts the image when the light level changes. Most scenes benefit from AGC operation.  
Select ON or OFF. The default is ON.  
NOTE: You can also use the rear panel button to enable or disable AGC (refer to Quick Setup).  
DIGITAL SLOW SHUTTER (DSS (SENS))  
Digital slow shutter (DSS) slows the picture frame rate and increases the camera sensitivity under low-light conditions by increasing the number  
of fields of integration. Use this option to enable or disable this feature, and to set the number of integration fields.  
Select one of the following options: OFF, 2, 4, 6, 8, 10, 20, 40. The default depends on the selected profile (refer to Table G.)  
NOTES:  
If you disable SENS on the rear panel, the camera saves the DSS (SENS) value on the EXPOSURE SETTING menu (refer to Quick Setup).  
This option is automatically disabled when AUTO EXPOSURE is set to MANUAL.  
Depending on the number of fields of integration, the picture will develop a granular appearance and motion may lag, resulting in a stereo-  
scopic effect or streaking on fast-moving objects.  
DAY AND NIGHT  
Use this option to specify how the camera will switch between day (color) and night (black and white) operation.  
Select one of the following options:  
AUTO  
Select this option to switch the filter automatically as light conditions change.  
The D&N DETECTION and D&N FILTER LIMIT settings appear.  
EXPOSURE SETTINGS  
AUTO EXPOSURE  
VIDEO LEVEL  
FLICKERLESS  
AGC  
> NORMAL  
> 0  
The camera switches from day to night when the AGC gain level reaches 22 dB.  
It switches from night to day when the AGC gain level reaches 16 dB.  
> OFF  
> ON  
> 4  
DSS(SENS)  
DAY & NIGHT  
D&N DETECTION  
D&N FILTER LIMIT  
BACK  
> COLOR  
>
When AUTO is selected, both the angle of view and the lighting conditions may  
cause the camera filters to switch constantly. Use the D&N FILTER LIMIT to  
compensate for this (refer to Day and Night Filter Limit).  
>
EXIT  
COLOR  
BW  
Select this option to operate the camera in day mode.  
Select this option to operate the camera in night mode.  
EXT.  
Select this option to use an external signal to switch between day and night modes (refer to Connecting External Control for more  
information). The D&N DETECTION and D&N FILTER LIMIT become enabled. In some installations, this option may be more  
reliable than AUTO mode.  
The default is COLOR, except for the DAY&NIGHT profile, whose default is AUTO.  
NOTES:  
You can also use the rear panel button to switch between AUTO and COLOR modes (refer to Quick Setup).  
When AGC is enabled, AUTO and EXT. modes are available. When AGC is disabled, AUTO and EXT. modes are not available; you can select  
only COLOR or BW mode.  
C2924M (4/05)  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
DAY AND NIGHT DETECTION  
The camera regularly checks the brightness level. When the brightness level crosses the switch threshold and lasts longer than the  
D&N DETECTION setting, the camera switches the filter.  
For example, the headlights of a passing car affect the brightness level in the camera, but not long enough for the filter to switch. The light of a  
cloudy day also affects the brightness level in the camera, long enough for the filter to switch.  
Select one of the following options: 5 SEC, 30 SEC. The default is 5 SEC.  
NOTE: This option is only enabled when the DAY & NIGHT option is set to AUTO or EXT.  
DAY AND NIGHT FILTER LIMIT  
In certain lighting conditions, the brightness level may cross the switch threshold quickly. As a result, the camera may constantly switch filters.  
Use this option to indicate how often to test the brightness level.  
Select one of the following detection test intervals:  
OFF  
Select this option to test the brightness level continuously, according to the D&N DETECTION setting (5 seconds or 30 seconds).  
Select this option to test the brightness level every 10 minutes.  
10 MIN  
30 MIN  
Select this option to test the brightness level every 30 minutes.  
The default is 10 MIN when the DAY & NIGHT profile is selected. Otherwise, the default is OFF.  
After the camera switches filters three times, and after the filter limit interval has passed, an asterisk (*) appears next to this setting. This indi-  
cates that the detection test has been performed.  
NOTE: This option is only enabled when the DAY & NIGHT option is set to AUTO or EXT.  
30  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
FUNCTION SETTINGS  
Select this option to configure the function settings for the CCC1390H Series camera.  
FUNCTION SETTINGS  
LINE SYNC  
WHITE BALANCE  
MANUAL RED/BLUE  
GAMMA  
SHARPNESS  
E-ZOOM  
MASKING  
TITLE  
BACK  
>
> AUTO  
>
> 60%(NORM)  
>
>
>
>
EXIT  
LINE SYNCHRONIZATION  
Use line synchronization to eliminate the vertical roll that occurs when multiple cameras are connected to the same switching device. Line  
synchronization locks each camera to the same frame rate.  
Line Sync  
Select one of the following line sync options:  
AUTO  
When using AC power, select this option to operate in line lock mode. This mode  
synchronizes the frame rate to the power phase. When selected, you can also  
manually set the vertical phase for this camera (refer to V-Phase Adjustment below  
and to Camera Synchronization for more information).  
LINE SYNC  
LINE SYNC  
> AUTO  
>
V-PHASE ADJ  
BACK  
EXIT  
INT  
Select this option to use the internal sync generator.  
The default is AUTO, except for the GAMING profile, whose default is INT.  
NOTES:  
When using DC power, the camera always uses the internal sync generator.  
When you select INT, the V-PHASE ADJ option is disabled.  
V-Phase Adjustment  
Use this menu to adjust the vertical phase for line synchronization. The range is 0 to 52 for NTSC  
cameras and 0 to 62 for PAL cameras.  
V-PHASE ADJ  
PHASE VALUE = 45  
Press the button up or down to adjust vertical phase. When correct, press the center of the button to  
return to the LINE SYNC menu.  
WHITE BALANCE  
The CCC1390H Series camera offers four white balance options. White balance settings define how the camera processes video images to render  
true colors in a scene. White balance is especially effective in scenes with changing color temperatures. Use it also in installations with  
incandescent, fluorescent, or outdoor lighting.  
Select one of the following white balance modes:  
AUTO  
In this mode, the camera automatically adjusts the white balance based on the colors in the camera scene. The camera  
continually delivers the best possible image.  
MANUAL  
Use this mode to calibrate the camera to the white balance in a neutral scene. This prevents dominant colors in the target scene  
from affecting white balance. Refer to Manual White Balance Calibration for more information.  
INDOOR  
Use this mode for indoor scenes. The white balance gain is set to about 2,800°K and does not change as the scene colors change.  
OUTDOOR  
Use this mode for outdoor scenes. The white balance gain is set to about 6,000°K and does not change as the scene colors  
change.  
C2924M (4/05)  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
MANUAL RED/BLUE  
MANUAL RED/BLUE  
Select this option to display the MANUAL RED/BLUE menu.  
RED GAIN  
BLUE GAIN  
RED HUE  
> -1  
> -2  
> 1  
Red Gain  
Use this option to either increase or decrease the light level of the red elements in the camera image.  
Select a value between -5 and 5. The default is -1.  
BLUE HUE  
> 1  
BACK  
EXIT  
Blue Gain  
Use this option to either increase or decrease the light level of the blue elements in the camera image. Select a value between -5 and 5.  
The default is -2.  
Red Hue  
Use this option to either increase or decrease the red hue in the camera image. Select a value between -5 and 5. The default is 1.  
Blue Hue  
Use this option to either increase or decrease the blue hue in the camera image. Select a value between -5 and 5. The default is 1.  
GAMMA  
Gamma correction adjusts the video signal to compensate for the nonlinear response of the monitor display.  
NOTE: When AUTO EXPOSURE is set to WDR, you cannot change the gamma setting.  
SHARPNESS  
Select this option to display the SHARPNESS menu.  
SHARPNESS  
APERTURE GAIN  
> -1  
Aperture Gain  
Use this option to increase or decrease the image sharpness, both vertically and horizontally. Select  
a value between -5 and 5. The default is -1.  
BACK  
EXIT  
E-ZOOM  
Select this option to configure electronic zoom, including electronic panning.  
E-ZOOM  
ZOOM  
POSITION  
> OFF  
>
NOTE: When you enable electronic zoom, both the WDR auto exposure mode and masking are  
disabled. If either WDR or masking is active, electronic zoom is disabled.  
BACK  
EXIT  
Zoom  
Select one of the following electronic zoom options: OFF, 1.5, 2.0, 2.5. The default is OFF.  
Position  
Use this option to pan and tilt the electronic zoom frame to a specific portion of the scene.  
POSITION  
To position the electronic zoom frame:  
1. Change the ZOOM setting on the E-ZOOM menu to 1.5. Positioning is possible only at 1.5 zoom.  
2. Select the POSITION menu. The POSITION menu appears.  
3. Press the button up, down, left, or right to position the frame. When correct, press the center of the button to return to the E-ZOOM menu.  
4. To use 2.0 or 2.5 zoom, change the ZOOM setting to the desired value.  
32  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
MASKING  
Masking lets you block out certain areas of a camera scene. Select this option to configure one to  
eight masks in the camera image.  
MASKING  
MASK  
MASK EDIT  
MASK ERASE  
> OFF  
>
NOTE: When you enable masking, electronic zoom is disabled. If electronic zoom is active, masking  
is disabled.  
BACK  
EXIT  
Mask  
Use this option to enable or disable masking. The default is OFF.  
Mask Edit  
Use this option to configure one or more masks. There is no default mask.  
MASK SETTING  
To edit a mask:  
1. Change the MASK setting on the MASKING menu to ON.  
2. Select the MASK EDIT menu. The MASK SETTING menu appears.  
3. Use the pointer to configure the mask area.  
a. Press the button up, down, left, or right to move the cursor to the upper left corner of the  
mask.  
b. Press the center of the button to mark the upper left corner.  
c. Press the button up, down, left, or right to move the cursor to the lower right corner of  
the mask.  
NOTE: If you move the cursor either left or above the start point, the mask edit is cancelled.  
d. Press the center of the button to mark the lower right corner. The mask area is blacked out. The MASKING menu appears with the  
new mask.  
4. Repeat step 3 for each additional mask.  
If you add a ninth mask, the camera erases the first mask. You cannot configure more than eight masks.  
Mask Erase  
Select this option to erase one or more masks. The camera erases masks from the last created to the first created.  
To erase a mask, select MASK ERASE. The mask that was last created disappears. Repeat to erase additional masks.  
TITLE  
Select this option to configure the camera title.  
TITLE  
Title  
TITLE  
EDIT TITLE  
> OFF  
>
Use this option to enable or disable the title display. The default is OFF.  
BACK  
EXIT  
Title Edit  
Use this option to enter or edit the camera title, up to 16 characters. The default is blank.  
To enter a camera title:  
EDIT TITLE  
1. Change the TITLE setting on the TITLE menu to ON.  
2. Select the EDIT TITLE menu. The EDIT TITLE menu appears.  
3. Press the button up, down, left, or right to move the cursor to the desired character.  
The space character is located below the letter n.  
ABCDEFGHIJKLM  
NOPQRSTUVWXYZ  
abcdefghijklm  
nopqrstuvwxyz  
0123456789-/  
BACK  
BS  
_________________  
4. Press the center of the button to select the character. The selected character appears in the  
blank area at the bottom of the screen.  
C2924M (4/05)  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5. To clear a character, select BS (backspace). The camera deletes the last character entered.  
6. Repeat steps 3 and 4 until you have entered the camera title.  
7. When the title is correct, select BACK to return to the TITLE menu.  
CAMERA SETUP  
Select this option to configure the serial communication and rear panel function settings for the  
CCC1390H Series camera. Refer to Connecting External Control for information on wiring the serial  
interface.  
CAMERA SETUP  
ADDRESS  
COM SPEED  
LED  
> 1  
> 4800  
> ON  
> ON  
SWITCH  
Address  
The CCC1390H Series camera can be accessed remotely from selected Pelco controllers. Use this  
option to assign a receiver address to the camera. This address identifies the camera on the serial  
chain. Select a value from 1 to 30. The default is 1.  
BACK  
EXIT  
NOTES:  
Each camera must have a unique address.  
Be sure to assign the address before accessing the camera remotely.  
COM Speed  
Use this option to set the communication or baud rate for this camera. This must match the setting for the other cameras and controllers on the  
serial chain. Select one of the following: 2400, 4800, 9600, 19200. The default is 4800.  
LED  
Select this option to enable or disable the rear panel indicators. The default is ON.  
Switch  
Select this option to enable or disable quick setup on the rear panel (refer to Quick Setup). The default is ON.  
AUTO IRIS LENS ADJUSTMENT  
Select this option to adjust the electronic properties of the auto iris lens to the auto iris electronic  
AI AUTO ADJUSTMENT  
properties of the camera. Perform this procedure before using the camera or each time you change  
the lens.  
OK  
CANCEL  
To perform this procedure:  
1. Mount the auto iris lens to the camera (refer to Lens Mounting).  
2. Aim the camera at a bright, flickerless scene.  
3. Select AI AUTO ADJUSTMENT. The AI AUTO ADJUSTMENT menu appears.  
4. Select OK. The camera performs the procedure. Then the MAIN MENU appears.  
34  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
PIXEL CORRECTION  
If white spots appear in the video image, one or more pixels on the camera imager may be defective.  
PIXEL CORRECTION  
This condition is common to CCD camera imagers.  
COVER THE LENS  
AND SELECT OK  
Select this option to automatically detect and correct these defects. This feature helps you maintain  
image quality.  
OK  
CANCEL  
To perform this procedure:  
1. Use a lens cap to cover the lens. Make sure no light can enter the lens.  
NOTE: The mechanical iris lens aperture does not completely block the light. Therefore, you should use a lens cap.  
2. Select PIXEL CORRECTION. The PIXEL CORRECTION menu appears.  
3. Select OK. The camera performs the procedure. Then the MAIN MENU appears.  
NOTES:  
Any defective pixels that cannot be completely corrected may still appear.  
Defective pixels may reappear when DSS(SENS) is enabled.  
SYSTEM INFORMATION  
Select this option to display the camera firmware information.  
SYSTEM INFORMATION  
FIRMWARE VERSION  
OSD VERSION  
1.0  
1.0  
Restore Factory Settings  
Select this option to reset the camera to the factory default settings. This option clears all saved  
user-definable settings, except the following:  
RESTORE FACTORY SETTINGS  
>
BACK  
EXIT  
CAMERA SETUP menu: ADDRESS, COM SPEED  
LINE SYNC menu: V-PHASE ADJ  
PIXEL CORRECTION  
RESTORE FACTORY SETTINGS  
To restore factory default settings:  
OK  
CANCEL  
1. Select RESTORE FACTORY SETTINGS on the SYSTEM INFORMATION menu. The RESTORE  
FACTORY SETTINGS menu appears.  
2. Select OK. The camera resets all parameters to the factory default settings, except those listed above. Then the MAIN MENU appears.  
C2924M (4/05)  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Lens Focusing  
After mounting the lens, you must focus your CCC1390H Series camera. You will adjust both the back focus (on the camera) and the fine focus (on  
the lens).  
NOTE: The back focus has already been adjusted using a standard CS-mount lens. However, you might need to adjust it again to match the  
mounted lens.  
1. Auto iris only: Cover the auto iris lens with a suitable neutral density (ND) filter. This opens the iris fully. For best results, use an ND3 filter.  
2. Manual iris only: Open the iris completely. Refer to Figure 12, which shows the manual iris, varifocal, and lens focus locking screws for a  
sample lens. Refer to your lens documentation for more information.  
MANUAL IRIS  
LOCKING SCREW  
LENS FOCUS  
1.5 MM  
LOCKING SCREW  
ALLEN  
WRENCH  
VARIFOCAL  
LOCKING  
SCREW  
Figure 12. Lens Focus  
3. If necessary, enable Automatic Gain Control (AGC) on the EXPOSURE SETTINGS menu.  
MAIN MENU  
AGC is enabled by default.  
PROFILES  
>
EXPOSU
a. Display the EXPOSURE SETTINGS menu.  
b. Change AGC to ON.  
EXPOSURE SETTINGS  
FUNC
CAM
AUTO EXPOSURE  
> NORMAL  
> 0  
> OFF  
> ON  
> 4  
> COLOR  
>
>
EXIT  
AI AU
PIXEL
SYST
VIDEO LEVEL  
FLICKERLESS  
AGC  
DSS(SENS)  
DAY & NIGHT  
D&N DETECTION  
D&N FILTER LIMIT  
BACK  
c. Select EXIT to save the AGC setting.  
4. Aim the camera at the farthest object in the field of view. Make sure it is at least 6.5 ft  
(2 m) away.  
5. Fixed focal length lens only:  
a. Set the lens focal length to far ().  
b. Adjust the back focus:  
(1) Use a 1.5-mm Allen wrench to loosen the back focus locking screw.  
(2) Turn the lens until the image is focused.  
(3) Tighten the back focus locking screw clockwise.  
WARNING: Do not over-tighten the back focus locking screw because you may damage the camera.  
Back focus is a coarse adjustment. You will make the fine focus adjustment in the next step.  
c. Adjust the lens focus to achieve the best fine focus.  
36  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
6. Varifocal lens only:  
a. Set the varifocal to wide (W) and the lens focal length to far ().  
b. Adjust the back focus:  
(1) Use the enclosed 1.5-mm Allen wrench to loosen the back focus locking screw.  
(2) Turn the lens until the image is focused.  
(3) Tighten the back focus locking screw clockwise.  
WARNING: Do not over-tighten the back focus locking screw because you may damage the camera.  
Back focus is a coarse adjustment. You will make the fine focus adjustment in steps c and d.  
c. Move the varifocal locking screw up or down to set the field of view.  
d. Adjust the lens focus to achieve the best fine focus.  
e. Repeat steps c and d until the focus is correct.  
7. Manual iris only: Adjust the iris for the best picture quality. The largest aperture gives the best light sensitivity; the smallest aperture  
gives the greatest depth of field.  
8. Tighten all lens locking screws.  
NOTE: When tightening the lens locking screws, do not over-turn or force any screw.  
9. Auto iris only: Remove the ND filter.  
MAIN MENU  
10. If necessary, disable AGC.  
PROFILES  
>
>
EXPOSUE SETTNS  
EXPOSURE SETTINGS  
FUNC
CAME
a. Display the EXPOSURE SETTINGS menu.  
b. Change AGC to OFF.  
AUTO EXPOSURE  
> NORMAL  
> 0  
> OFF  
> OFF  
> 4  
> COLOR  
>
AI AU
PIXEL
SYST
VIDEO LEVEL  
FLICKERLESS  
AGC  
DSS(SENS)  
DAY & NIGHT  
D&N DETECTION  
D&N FILTER LIMIT  
BACK  
c. Select EXIT to save the AGC setting.  
11. Auto iris only: Perform the auto iris lens adjustment procedure (refer to Auto Iris Lens  
>
EXIT  
Adjustment).  
12. As soon as you finish customizing this and all other camera settings, save your custom  
settings into the CUSTOM profile. This protects them in case the camera loses power  
or must be restarted (refer to Profiles for more information).  
C2924M (4/05)  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Camera Synchronization  
Camera synchronization may affect installations that use two or more AC power supplies for multiple cameras. Due to different power phases,  
a brief vertical roll may appear on the monitor when switching between cameras. To eliminate this vertical roll, adjust the phase control to  
synchronize the cameras to one another.  
It may be necessary for two people to communicate when synchronizing cameras, one at the camera and the other at the monitor, to observe the  
vertical roll and the effect of any camera adjustments.  
To synchronize cameras:  
1. Choose a reference camera to which all other cameras will be phased.  
2. Access V-PHASE ADJ menu for a camera. Press the button up and down to adjust the vertical phase until the camera is synchronized to the  
reference camera.  
A dual trace oscilloscope is recommended, but not required, to adjust camera phase. Align the vertical sync pulses of the reference camera  
to the selected camera.  
3. After each adjustment, switch back and forth between the adjusted camera and the reference camera. Repeat this process until the roll  
between the cameras disappears completely.  
4. Adjust the phase of all other cameras by repeating steps 2 and 3. Always adjust to the reference camera selected in step 1.  
5. As soon as you finish customizing this and all other camera settings, save your custom settings into the CUSTOM profile. This protects them  
in case the camera loses power or must be restarted (refer to Profiles for more information).  
To adjust phase control:  
MAIN MENU  
1. Select LINE SYNC on the FUNCTION SETTINGS menu. The LINE  
SYNC menu appears.  
PROFILES  
>
>
EXPOSRE ETTINS  
FUNCTION SETTINGS  
FUNC
CAME
2. Switch the LINE SYNC setting to AUTO.  
LINE SYNC  
>
AI AU
PIXEL
SYST
WHIT
3. Select V-PHASE ADJ. The V-PHASE ADJ menu appears.  
LINE SYNC  
MAN
GAM
SHAR
LINE SYNC  
> AUTO  
4. Press the button up or down to change the PHASE VALUE. On the  
CCC1390H-6 (NTSC) camera, the range is 0 to 52. On the  
CCC1390H-6X (PAL) camera, the range is 0 to 62.  
V-PH
E-ZOO
MASK
TITLE  
V-PHASE ADJ  
PHASE VALUE = 45  
BACK  
BACK  
5. Press the center of the button to return to the LINE SYNC menu.  
6. Select EXIT to close the setup menus.  
7. As soon as you finish customizing this and all other camera settings, save your custom settings into the CUSTOM profile. This protects them  
in case the camera loses power or must be restarted (refer to Profiles for more information).  
38  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Manual White Balance Calibration  
In some installations, use manual white balance to render the most accurate image color possible. Mixed color applications may affect the  
amount of color adjustment. For example, a small white object on a large blue surface may have a reddish tint. Manual white balance uses a  
calibration image to identify the correct white level. The camera then uses this white level when adjusting overall image color.  
NOTE: Manual white balance is recommended only for indoor applications that have a single primary light source.  
Example: A CCC1390H camera is installed in a pan/tilt enclosure in a clothing store in a shopping mall. Mixed colors are located throughout the  
store. Overhead lights provide the primary illumination, but some light also enters the store from the mall. As the camera pans a section filled with  
blue clothing, the camera may redden the image to compensate for the blue. When properly calibrated, the camera will not try to adjust scenes  
with predominant amounts of red or blue.  
To calibrate the manual white balance:  
1. Focus the camera on a neutral color scene. Select a neutral scene with the following characteristics:  
Little or no black  
Not predominantly red  
Not predominantly blue  
No direct light source, such as a lamp or a window  
MAIN MENU  
PROFILES  
2. Select WHITE BALANCE on the FUNCTION SETTINGS menu.  
>
EXPOS
3. Select AUTO. This calibrates the white balance gain to the neutral scene.  
FUNCTION SETTINGS  
FUNC
CAME
LINE SYNC  
>
AI AU
PIXEL
SYST
4. Change WHITE BALANCE from AUTO to MANUAL. This locks the white balance  
gain into camera memory.  
WHITE BALANCE  
> AUTO  
MANUAL RED/BLUE  
>
GAMMA  
SHARPNESS  
E-ZOOM  
MASKING  
TITLE  
> 60%(NORM)  
>
NOTE: If you change WHITE BALANCE from MANUAL to a different mode, the stored  
manual white balance settings are erased. You will have to perform this procedure again.  
>
>
>
BACK  
EXIT  
5. Select EXIT to close the setup menus.  
6. Focus the camera on the target scene.  
7. As soon as you finish customizing this and all other camera settings, save your custom settings into the CUSTOM profile. This protects them  
in case the camera loses power or must be restarted (refer to Profiles for more information).  
C2924M (4/05)  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Specifications  
GENERAL  
Day/Night Operation  
Day  
Infrared (IR) cut filter  
Night  
BK-7 glass, same optical displacement as day  
Imaging Device  
Dynamic Range  
1/3-inch image format Sony SS-2WD CCD  
60 dB maximum (WDR mode)  
Picture Elements  
NTSC  
PAL  
768 (H) x 494 (V) (approx. 380K)  
752 (H) x 582 (V) (approx. 440K)  
Sensing Area  
3/16 x 1/8-inch (4.76 x 3.18 mm)  
525 (NTSC)/625 (PAL), 2:1 interlace  
Internal/AC line lock  
Scanning System  
Synchronization  
Horizontal Resolution  
Iris Control  
530 TV lines (B-W); 480 TV lines (color)  
Selectable: on/off  
Electronic Shutter Control  
NTSC  
PAL  
Selectable: on/off  
1/60-1/50,000  
1/50-1/50,000  
Auto Iris Lens Type  
DC-drive (autosensing)  
Sensitivity  
Color  
Color (SENS 40x)  
B-W  
0.8 lux, F1.2, 40 IRE, AGC on, 75% scene reflectance  
0.02 lux, F1.2, 40 IRE, AGC on, 75% scene reflectance  
0.08 lux, F1.2, 40 IRE, AGC on, 75% scene reflectance  
2x, 4x, 6x, 8x, 10x, 20x, 40x  
Digital Slow Shutter (SENS)  
Filter Switching Threshold  
Day to Night  
Night to Day  
1.6 lux, average scene illumination  
1.9 lux, average scene illumination  
Signal-to-Noise Ratio  
Vertical Phase  
>48 dB  
Adjustable 90˚  
Automatic Gain Control  
Backlight Compensation  
Flickerless Mode  
Selectable: on/off, adjustable to 24 dB  
Selectable: on/off  
Selectable: on/off; 1/100 sec (NTSC),  
1/120 sec (PAL)  
Internal Synchronization  
Auto White Balance  
Day/Night  
Selectable: on/off  
Selectable: on/off, 4 modes  
Selectable: on/off, 4 modes  
Digital signal processing (DSP)  
1 Vp-p, 75  
Signal Processing  
Video Output  
Gamma Correction  
Electronic PTZ  
Selectable: on/off, 0.45, 0.6, 1.0  
Selectable: 1.5X, 2.0X, 2.5X  
2,500° to 8,600°K  
White Balance Range  
40  
C2924M (4/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
ELECTRICAL  
Power Requirements  
CCC1390H-6  
CCC1390H-6X  
24 VAC 15%/12 VDC 15%, 60 Hz  
24 VAC 15%/12 VDC 15%, 50 Hz  
Power Consumption  
Power Connector  
Video Connector  
Auto Iris Connector  
Mode Indicators  
Controls  
3.5 watts: 270 mA, 24 VAC; 390 mA, 12 VDC  
3-pin terminal strip, push-in type  
BNC  
4-pin connector (miniature square)  
4
5-position switch  
Serial data termination switch  
Control Connector  
7-pin micro (1.25 mm) connector  
Data I/O (Pelco P or Pelco D protocol)  
External day/night switch  
MECHANICAL  
Lens Mount  
CS mount  
Camera Mount  
1/4-inch UNC-20 screw, top or bottom of camera housing  
ENVIRONMENTAL  
Operating Temperature  
Storage Temperature  
Humidity  
14° to 122°F (-10° to 50°C)  
-40° to 140°F (-40° to 60°C)  
20% to 80% (noncondensing)  
PHYSICAL  
Dimensions  
2.2” D x 2.09” W x 2.17” H  
(5.6 x 5.3 x 5.5 cm)  
Weight (without lens)  
Shipping Weight  
0.44 lb (0.20 kg)  
1 lb (0.45 kg)  
(Design and product specifications subject to change without notice.)  
C2924M (4/05)  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelco’s liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
REVISION HISTORY  
Manual #  
Date  
Comments  
C2924M  
4/05  
Original version.  
Pelco, the Pelco logo, Spectra, Genex, Legacy, Esprit, DomePak, ImagePak, and Camclosure are registered trademarks of Pelco.  
PelcoNet, Endura, and ExSite are trademarks of Pelco.  
©Copyright 2005, Pelco. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East  
|
|
|
|
|
|
|
|
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Cordless Telephone ONIS 6816 User Manual
Philips Network Router PTN3501 User Manual
Philips Work Light HB977 User Manual
Philips Work Light PTS7 User Manual
Polycom Telephone IP 4000 SIP User Manual
Polycom Universal Remote The Remote Control User Manual
Poulan Blower 530088125 User Manual
Precor Treadmill 776i User Manual
Pride Mobility Mobility Aid Jazzy Select 14 User Manual
ProForm Home Gym PFEL19010 User Manual