Models: PLA 60, PLA 60-S,
PLAV 60, PLAV 60-S
Installation and Assembly - Articulating Swivel Arm for
37" - 60" Plasma Screens
This product is UL Listed. It must be
installed by a qualified professional
installer.
R
Maximum UL Load Capacity: 175 lb (79 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you start make sure all parts
listed are included with your product.
D M
Parts List
PLA 60
QTY. PART #
PLA 60-S
PART #
PLAV 60
PART #
PLAV 60-S
PART #
DESCRIPTION
A wallplate
1
201-1040
201-4040
201-1040
201-4040
B tilt-roll assembly
1
1
1
3
8
1
1
1
2
1
8
1
1
8
8
1
4
4
1
1
201-1093
201-1072
201-1041
600-1012
520-9262
540-1074
560-0108
520-1315
540-1070
520-1210
590-1123
580-1166
590-1007
520-1243
540-1063
560-9728
590-1166
590-1168
600-1015
560-9716
201-4093
201-4072
201-1041
600-1012
520-9262
540-1074
560-0108
520-1315
540-1070
520-1210
590-1123
580-1166
590-1007
520-1243
540-1063
560-9728
590-1166
590-1168
600-1015
560-9716
201-1048
201-1049
201-1041
600-1012
520-9262
540-1074
560-0108
520-1315
540-1070
520-1210
590-1123
580-1166
590-1007
520-1243
540-1063
560-9728
590-1166
590-1168
600-1015
560-9716
201-4048
201-4049
201-1041
600-1012
520-9262
540-1074
560-0108
520-1315
540-1070
520-1210
590-1123
580-1166
590-1007
520-1243
540-1063
560-9728
590-1166
590-1168
600-1015
560-9716
E
F
C arm assembly
D wall support arm axle
E vinyltrim
F M10 x 1.5 x 15 mm screw bolt
G .505 x .75 x .062" nylon washer
H tilt adjustment knob
I carriage bolt 3/8"-16 x 3.25"
J 1.525 x 2 x .062" delrin washer
K #8-32 x .375" socket head cap screw
L plastic finishing cap
M holdingpin
G
H
K
N
N retainerplug
O 5/16 x 3" wood screw
P .250 x 1 x .068" washer
Q 9/64"allenwrench
R cable management clips
S cable tie
T 36" polyester mesh sleeve
U 6 mm allen wrench
V 10 mm allen wrench
W anchor
1
8
n/a
590-1025
n/a
590-1025
560-9727
590-1025
560-9727
590-1025
L
A
C
J
R
P
B
T
W
V
U
I
Q
O
S
Some parts may appear slightly different than illustrated.
3 of 9
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation to Wood Stud Wall
WARNING
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal
studs (contact customer care). Metal stud installation is not UL evaluated.
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers
are responsible to provide hardware for other types of mounting situations.
• Never exceed the Maximum UL Load Capacity of 175 lb (79 kg).
Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the
1
studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line
down each stud’s center. Place wall plate on wall as a template. The top mounting slots should be located .36"
above the desired screen center for PLA 60 and PLA60-S and .43" below the desired screen center for PLAV 60
and PLAV 60-S. Level plate, and mark the center of the eight mounting holes. Make sure that the mounting
holes are on the stud centerlines. Drill eight 7/32" dia. holes 3" deep. Make sure that the wall plate is level,
secure it using eight 5/16 x 3" wood screws (O) and washers (P).
Skip to step 2 on page 6.
WARNING
• Never mount this product to metal studs without the
required accessory.
P
O
A
ISSUED: 05-02-06 SHEET #: 202-9112-2 06-21-06
4 of 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation to Concrete Wall
WARNING
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity of 175 lb (79 kg).
• Never mount this product to metal studs.
IMPORTANT! Concrete must be 2000 psi density
minimum.
concrete
surface
1
Use wall plate (A), making sure that it is level, as a
template to mark holes. The top mounting slots should
be located .36" above the desired screen center for PLA
60 and PLA 60-S and .43" below the desired screen
center for PLAV 60 and PLAV 60-S. Use the masonry bit
to drill 5/16" (8 mm) dia. holes to a minimum depth of 3"
(76 mm). Insert anchors in holes flush with wall as shown
(right). Place wall plate (A) over anchors (W) and secure
with 5/16 x 3" wood screws (O) and washers (P).
1
W
Drill hole(s) and insert anchor(s) (W)
mounting
plate
2
WARNING
W
• Tighten wood screws so that wall plate is firmly
attached, but do not overtighten. Overtightening can
damage screws, greatly reducing their holding power.
Place plate over anchor(s) (W) and secure with screw(s)(O)
3
• Never tighten in excess of 80 in • lb (9 N.M.).
Tighten all fasteners
WARNING
• Always attach concrete expansion anchors directly to
load-bearing concrete.
• Never attach concrete expansion anchors to concrete
covered with plaster, drywall, or other finishing mate-
rial. If mounting to concrete surfaces covered with a
finishing surface is unavoidable, the finishing surface
must be counterbored as shown below. If plaster/
drywall is thicker than 5/8", custom fasteners must be
supplied by installer (Not evaluated by UL).
W
P
O
CORRECT
INCORRECT
mounting
plate
concrete
concrete
mounting
plate
A
plaster/
drywall
plaster/
drywall
5 of 9
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
• If you are uncertain that product is properly installed, call customer care.
Note: There are five mounting positions. The
N
J
D
2
center position is shown (right). Slide washer (J)
over wall support arm axle (D). Next, insert plastic
cap (N) into axle. Then, insert holding pin (M) into
axle. See detail 1.
M
Place arm assembly (C) with washer (J) into wall
plate (A). Insert axle assembly shown in detail 1
through wall plate (A), arm assembly (C), and
washer (J). Lock axle in place by aligning holding
pin (M) with notches shown in detail 2.
2-1
2-2
DETAIL 1
A
J
Insert socket cap screw (K) into hole at bottom of
wall support arm axle (D) as shown in detail 3.
Tighten screw using 9/64" allen wrench (Q).
NOTCH
C
DETAIL 2
Note: Fit of axle (D) into wall plate (A) and arm
assembly (C) will be tight. Gently tap into place
with a hammer if necessary.
K
D
DETAIL 3
Snap four cable management clips(R)into top or bottom of arm assembly(C)as shown. Cable ties (S) are used
with clips for cord management.
3
Slide one mesh sleeve (T) over each cable. Use cable ties (S) to tighten mesh sleeves to cables.
3-1
T
R
C
S
ISSUED: 05-02-06 SHEET #: 202-9112-2 06-21-06
6 of 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm
assembly (C).
4
Insert one finishing cap (L) into each unused hole of wall plate (A).
4-1
L
A
SWIVEL BOX
C
E
Note: Refer to adapter bracket instruction sheet for attachment of adapter bracket to plasma before proceeding
with step 5. If your adapter bracket has an aluminum race attached to it, remove before proceeding and discard race. It is
not used with this product.
Insert and tape carriage bolt (I) into top hole of pitch-roll assembly (B). Attach tilt-roll assembly to adapter
bracket with four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U).
5
Note: Adapter bracket (not UL evaluated, sold separately) will vary in size and style.
CAUTION
GENERIC
ADAPTER BRACKET
• Do not overtighten screws! Overtightening may hinder
roll option.
I
B
F
7 of 9
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
• Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV.
Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed
thread.
6
SWIVEL BOX
C
.25"
F
Hook tilt-roll assembly (B) onto M10 screws (F).
Insert carriage bolt (I) into slot of swivel box as
shown in figure 6.1. Install nylon washer (G) and tilt
adjustment knob (H).
6-1
6-2
CAUTION
• After tilt is adjusted, all fasteners must be tightened.
Failure to do so will result in damage to the mount.
Install remaining two M10 screws (F) as shown in
figure 6.2. HAND TIGHTEN all four M10 screws to
allow for tilt adjustment. Remove tape from carriage
bolt (I). For tilt adjustment, push back on the top of
plasma to relieve pressure on knob. Adjust tilt to
desired position and tighten tilt adjustment knob (H),
then securely tighten all four M10 screws (F) using 6
mm allen wrench (U).
H
I
H
G
SWIVEL BOX
I
F
F
B
fig 6.1
fig 6.2
ISSUED: 05-02-06 SHEET #: 202-9112-2 06-21-06
8 of 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Depending on the specific size & weight of the plasma,
articulating swing arm may be angled at different
positions, causing plasma to appear to lean sideways
at different articulating positions. Tilt-roll assembly (B)
allows plasma to be manually adjusted, so plasma can
be horizontal at all positions. To adjust, gently rotate
plasma by hand to desired position.
If it is too difficult to adjust roll of plasma, loosen
screws shown in figure 7.1 using a phillips screw-
driver.
7-1
7
IMPORTANT! Do not loosen or tighten screws
more than 1/8 turn.
ARTICULATING ARM
PLASMA
ROLL
ADJUSTMENT
SCREWS
FOR PLAV 60 ONLY:
Position of screen may be adjusted vertically up to
.79" in each direction by doing the following:
• To lower screen, turn socket screw shown in figure
8.1 clockwise with 10 mm allen wrench (V).
8
• To raise screen, turn socket screw shown in figure
8.1 counterclockwise with 10 mm allen wrench (V).
fig 7.1
SOCKET
SCREW
fig 8.1
9 of 9
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06
©2006 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
|