Installation and Assembly:
Wall Mount for SMARTboard SB685/SB690
Model: IWB600-WB
Max Load Capacity: 50 lb (22.6 kg)
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
Download from Www.Somanuals.com. All Manuals Search And Download.
1 of 7
WARNING
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
NOTE: Make sure flange of wall bracket is located on top as shown in detail 1
Be sure wall bracket (A) is level and in desired position. Then use wall bracket (A) as a template to mark center
of four mounting holes. Drill four mounting holes. Attach wall bracket (A) to mounting surface using four screws
provided by installer and four 1/4 washers (J) if required. Once secure, wall bracket (A) will be flush with the top of
the vertical bracket (D).
1
Fasten two M4 x 6 mm phillips screws (G) into ends of wall bracket (A) as shown in Detail 1.
NOTE: Vertical brackets (D) may be used to determine location of wall bracket (A).
A
A TOP
Flange
G
Detail 1
Screws provided by installer
J
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
3 of 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure Vertical brackets (D) to wall bracket (A) using two #10-32 x 3/8 thumb screws (H) and #10 flat washers
(F).
2
F
H
Detail 2
D
Secure SMARTboard channel to upper cross support (B) using eight M5 x 20 mm phillips screws (N) and eight
M5 nylock nuts (L).
NOTE: Make sure to skip attachment point as shown below.
3
B
Skip attachment point
L
SMARTboard
channel
Skip attachment point
N
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
4 of 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure upper cross support (B) to vertical supports (D) using four M4 x 8 mm phillips screws (M), and
M4 nylock nuts (K).
4
D
K
B
B
M
Detail 3
M
Hook SMARTboard into SMARTboard channel on upper cross support (B).
5
SMARTboard
channel
B
SMARTboard
SMARTboard
channel
Detail 4
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
5 of 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Fasten two support brackets (C) to vertical supports (D) using four #10-32 x 3/8 thumb screws (H).
Slide support brackets (C) up until bottom of SMARTboard rests on support as shown in detail 5.
Tighten four #10-32 x 3/8 thumb screws (H).
6
H
H
C
D
Detail 5
C
Fasten knob (I) through outside hole in support bracket (C) to determine rubber bumper (E) placement.
Secure rubber bumper (E) to board.
Repeat on opposite side of board.
7
E
C
I
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
6 of 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure bottom of vertical supports (D) to mounting surface using two screws provided by installer,
and 1/4 washers (J) if required.
8
NOTE: Make sure mounting surface is suitable to hold the weight of the mount and smart board.
Screws provided by
installer
J
D
ISSUED: 02-03-10 SHEET #: 125-9095-5 06-02-10
7 of 7
© 2010, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
|