Installation and Assembly
Flat-Panel Base Lock-Down Kit For Philips Display
Models
Models: HLG452-002, HLG452-002-Q10
Maximum Display Weight: 100 lb (45.35 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Option 1 (Fasteners)
DISPLAY MODEL HOLE PATTERNS
SBP240M/27
A.
42HF7945D/27
37HFL5560D/27
42HFL55860D/27
42HFL7945D/27
42HFL7580A/27
52HFL5580D/27
B.
C. 26HFL5830D/27
32HFL5460D/27
32HFL5860D/27
32HFL7560D/27
32HF7965D/27
32HFL7965D/27
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
Use lock-down plate (A) as a template to mark location
of holes, point 1 and point 2, approximately 7" apart on
table. Drill two holes using a 1/4'' drill bit.
Slide two 1/4-20 x 1 3/4" bolts (B) through slots as
shown below.
2
1
NOTE: 2 1/4" carriage bolts (ACC939) are available
for use with thicker mounting surfaces.
7"
B
(178 mm)
POINT 2
POINT 1
A
TABLE TOP
3 of 6
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09
For customer care call 1-800-729-0307 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach lock-down plate to display base bottom using
screws provided by manufacturer. Refer to page three
for lock-down plate/ display base stand hole pattern.
NOTE: Remove existing rubber feet from display base
that interfere with the lock-down plate.
Hand tighten slope nut (D) through 1/4-20 x 1 3/4"
screw bolt (B) until snug against bottom of desktop
surface. Thread another slope nut (D) upside-down,
about two turns from first slope nut (D). Insert a open
box wrench between both slope nuts (D) and tighten.
NOTE: Avoid jamming both slope nuts (D) together,
doing so may make it difficult to remove slope nut
used for tightening first slope nut (D). After slope nut is
secure remove bottom slope nut and add plastic cap
(C) as shown in figure 4.2. Repeat with remaining
1/4-20 x 1 3/4" screw bolt (B).
3
4
DISPLAY BASE STAND
RUBBERFEET
BOTTOM OF DESKTOP
A
SCREWS SUPPLIED BY
B
B
MANUFACTURER
D
TIGHTENING
SLOPE NUT
NOTE: Display base stand and mounting
hole locations may appear different than
illustrated.
C
FIG 4.1
FIG 4.2
4 of 6
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09
For customer care call 1-800-729-0307 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Option 2 (Adhesive Strips)
DISPLAY MODEL HOLE PATTERNS
Attach lock-down plate to display base bottom using
screws provided by manufacturer. Refer to lock-down
plate/ display base stand hole pattern.
SBP240M/27
A.
NOTE: Remove existing rubber feet from display base
that interfere with the lock-down plate.
42HF7945D/27 HOLE PATTERN SHOWN
DISPLAY BASE STAND
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
42HF7945D/27
B.
37HFL5560D/27
42HFL55860D/27
42HFL7945D/27
42HFL7580A/27
52HFL5580D/27
RUBBERFEET
A
SCREWS SUPPLIED BY
MANUFACTURER
NOTE: Display base stand and mounting
hole locations may appear different than
illustrated.
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
C. 26HFL5830D/27
32HFL5460D/27
32HFL5860D/27
32HFL7560D/27
32HF7965D/27
32HFL7965D/27
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
5 of 6
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09
For customer care call 1-800-729-0307 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
Clean bottom of lock-down plate (A) with rubbing alcohol. Spray bottom of lock-down plate (A) only where tape will
be applied, with 3M rubber and vinyl #80 spray adhesive. Pull apart the four adhesive strips (E) and remove red
backing film on both sides. Wait at least 4 minutes to dry before applying adhesive strip (E). Attach adhesive
strips (E) firmly to bottom of lock-down plate (A) as shown below.
4
CLEAN WITH
RUBBING
ALCOHOL
DRIED 3M
RUBBERAND
VINYL #80 SPRAY
ADHESIVE
E
A
Clean desk surface with rubbing alcohol. Use 3M rubber and vinyl #80 spray adhesive (not supplied) on the mounting
surface area only. NOTE: Spray adhesive will not remove easily. Wait at least 4 minutes to dry before removing tape
backing from lock-down plate (A) and placing firmly on surface. NOTE: There is a recommended 72 hour cure time for
tape on lock-down plate (A).
NOTE: Once tape backing is removed be careful not to touch the sticky surface of the tape with fingers, as this can
cause the tape to lose some of its holding power.
NOTE: After application of tape on lock-down plate (A), the bond strength will increase as the adhesive flows onto the
surface.
At room tempurature, approximately 50%
of the ultimate strength will be achieved
after 20 minutes, 90% after 24 hours,
and 100% after 72 hours. In some cases,
bond strength can be achieved more quickly
by exposure to elevated temperatures
(e.g. 150°F [66°C] for 1 hour).
DISPLAY BASE STAND
DRIED 3M RUBBERAND
VINYL #80 SPRAY
ADHESIVE (not supplied)
DESK SURFACE
NOTE: Display base stand may appear
different than illustrated.
6 of 6
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09
For customer care call 1-800-729-0307 or 708-865-8870.
Download from Www.Somanuals.com. All Manuals Search And Download.
|