PR®15 D
Powered bi-amplified two-way speaker system
Operating
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using electrical products, basic cautions should always be followed, including the following:
1.
Read these instructions.
2.
3.
4.
5.
6.
7.
8.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that
produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit
from the apparatus.
11.
Only use attachments/accessories provided by the manufacturer.
12.
Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
14.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such
as when power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
15.
Never break off the ground pin. Write for our free booklet “Shock Hazard and Grounding.” Connect only to a power supply of
the type marked on the unit adjacent to the power supply cord.
16.
17.
If this product is to be mounted in an equipment rack, rear support should be provided.
Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your plug‚
proceed as follows:
a) The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E‚ the earth symbol‚
colored green or colored green and yellow.
b) The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black.
c) The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red.
18.
19.
This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place objects
containing liquids, such as vases, upon the apparatus.
The on/off switch in this unit does not break both sides of the primary mains. Hazardous energy can be present inside the
chassis when the on/off switch is in the off position. The mains plug or appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.
20.
Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to
noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient
time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible
noise level exposures:
Duration Per Day In Hours
Sound Level dBA, Slow Response
8
6
90
92
4
3
95
97
2
1.5
1
.5
100
102
105
110
115
.25 or less
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Earplugs or protectors to
the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if
exposure is in excess of the limits as set forth above. To ensureagainst potentially dangerous exposure to high sound pressure levels, it is
recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be
protected by hearing protectors while this unit is in operation.
SAVE THESE INSTRUCTIONS!
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
PR™ 15D
®
Thank you for purchasing the class D powered PR 15D. The PR 15D features a bi-amped power section that provides 150 watts power
for the woofer and 50 watts power for the compression driver tweeter, both with Peavey-exclusive DDT compression. Featuring
a 15” heavy duty woofer and the RX 14 compression driver, the PR 15D provides an XLR and 1/4”phone combo jack, with mic/line
™
™
switchable level, balanced input with volume control.
Features
• Bi-amplified Class D powered system with 200 watt total power
• Both power amps have DDT compression
• 15" heavy duty woofer with 2.375" voice coil and Neodymium Magnet
• Woofer servo for reduced woofer distortion
• Automatic equal loudness (Fletcher-Munson)
• RX 14 1.4" titanium compression driver
• Peak SPL up to 120 dB with music!
• Combo jack with 1/4" TRS & female XLR mic- or line-level balanced input
• Two 1/4" phone jacks for link-out/direct-in capability
• Molded-in horn with exceptionally smooth response and pattern control
• Top and sides handgrips
• Pole mount molded-in
• Reduced weight
• Top and bottom flying point inserts
Description
The Peavey PR 15D is a powered, bi-amplified, two-way speaker system engineered to provide very high levels of performance in a
compact powered loudspeaker. The PR 15D is capable of up to 120 dB peak SPL. The enclosure utilizes tough polypropylene in an
injection-molded plastic trapezoidal form, with a coated steel grille to offer an attractive yet-durable powered speaker system.
™
This two-way powered system is comprised of a 150 W class D power amplifier driving a 15" heavy duty woofer. The RX 14
compression driver is driven by a 50 W class D power amplifier and features a 1.4” titanium diaphragm coupled to an extremely smooth
and well-controlled constant directivity horn (with a coverage pattern of 90˚ by 40˚) that is molded integrally into the enclosure.
A balanced input to the preamp/EQ electronics consists of one combo female XLR and 1/4” TRS phone jack. It is switchable between
mic-level and line-level sensitivity. Two 1/4” phone jacks are provided for link-out / direct-in capability. The link-out is post- level and
pre-crossover. While the direct-in is a direct pre-crossover input.
A woofer servo senses back-EMF from the woofer voice coil that is not a result of the drive signal, and subtracts the error so that the
woofer cone follows the drive waveform precisely.
Constant Loudness (Fletcher-Munson) circuit for accenuating bass and treble at low listening volume levels.
The power amplifiers providing the bi-amplification are low-distortion units providing 150 W continuous RMS into the nominal 8 ohm
load of the woofer, and a 50 W continuous RMS into the nominal 8 ohm load of the tweeter. They were selected for their reliability and
™
superb musical performance capability. Both amplifiers feature our patented DDT compression, which virtually eliminates audible
power amplifier clipping.
™
A molded-in handle provides ease of transport, while multiple mounting points (top and bottom) for the Peavey Versamount allow
maximum utility.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Applications
®
The Peavey PR 15D has a variety of applications such as sound reinforcement, public address, side fill
system, karaoke or musical playback. With the optional monitor stand kit, the Peavey PR 15D makes an
excellent stage monitor.
A typical signal source for the line-level inputs of the Peavey PR 15D would be a sound reinforcement
mixing console (mixer) or the output from a CD player, iPod player or tape deck. A dynamic microphone
can be connected and used as well.
R E A R P A N E L
1
2
FuSE
The unit is AC power line fuse protected from overloads and fault conditions with a fast-blow 3.15 Amp
fuse. This fuse is located within the cap of the enclosure. If the fuse fails, THE FUSE MUST BE REPLACED
WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PREVENT
VOIDING THE WARRANTY. If the unit blows a fuse, it should be taken to a qualified service center for repair.
1
IEC POWER CORD CONNECTION
This receptacle is for the IEC line cord (supplied) that provides AC power to the unit.
It is very important that you ensure the PR 15D has the proper AC line voltage supplied. You can find the proper voltage
for your PR 15D printed next to the IEC line (power) cord on the rear panel of the unit. Please read this guide carefully
to ensure your personal safety as well as the safety of your equipment.
Never break off the ground pin on any equipment. It is provided for your safety. If the outlet used does not have
a ground pin, a suitable grounding adapter should be used and the third wire should be grounded properly. To
prevent the risk of shock or fire hazard, always be sure that the mixer and all other associated equipment are
properly grounded.
2
ON-OFF SWITCH
This rocker switch supplies AC power to the PR 15D when switched to the ON position.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
F R O N T P A N E L
5
4
6
6a
7
8
9
10
4
GROuND LIFT
Switches the XLR (5) PIN 1 from direct contact with ground in the event that hum occurs.
5
6
PRIMARY INPuT (CHANNEL 1)
The primary input is switchable between line-level and mic-level input. The line-level input is of the
medium impedance balanced type, and when switched to mic-level(6) it is of a typical low-Z mic input
impedance. Jack (5) is a combo female XLR and 1/4" TRS connector.
PAD
Switches the sensitivity of Channel 1 from line-level to mic-level sensitivity. Pushed in, the sensitivity is
set for line-level input signals. When the switch is not pushed in, the sensitivity is increased by 30 dB so
it is suitable for mic-level signals.
6a
7
PAD STATuS LED
Illuminates green when PAD switch (6) is in line-level mode, and yellow when the PAD is in mic-level mode.
VOLuME
Controls the gain (level) of the Primary Input (5), Channel 1, of the powered speaker system. It is used to
directly set the system output level for the Channel 1 input signal.
8
9
POWER/CLIP LED
Illuminates GREEN when the electronics receive power (when the Power switch (3) is On). Illuminates RED
when amplifier clipping is occurring or the unit has tripped the thermal protection system.
LINK OuT
Link Out is a 1/4" post-level send intended for the use of linking multiple PR 15D's in a line. In that case, the
Link Out would connect to the 1/4" connections of the MIC/LINE (5) input of the next PR 15D in the line of PR
speakers. All of the PR 15D's in the line should have their respective PADs (6) engaged and Level control (7) set
to mid-position. The first PR can use it's level control to set the volume for all of the PR speakers in the line.
10
DIRECT IN
Direct In is a 1/4" line input that can be used to drive the PR 15D directly from a mixer, or other line level
source. This input jack has switching contacts that disconnects the PR 15D pre-amp, therefore the level
control on the PR 15D does not affect the volume of the speaker.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
O P E R A T I N G I N S T R u C T I O N S
Cautions
The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing
to qualified service personnel.
The heat sink on the back plate can become hot to the touch. Do not block or cover the heat sink from
ventilation.
Be sure to keep the microphone away from the front of the speaker after switching the mic sensitivity pad
to the OUT position and while setting the microphone level, or very loud feedback will occur! Damage to
the system is likely if this occurs!
®
DO NOT connect the inputs of the PR 15D to the output of a power amplifier. The inputs are meant to be
driven from a line-level strength signal.
DO NOT remove the protective metal grille.
®
Warning: The PR 15D is very efficient and powerful! This sound system can permanently damage hearing!
Use extreme care setting the overall maximum loudness!
®
The apparent sound level of the PR 15D can be deceiving due to its clear, clean sound output. The lack of
distortion or obvious distress can make the sound level seem much lower than it actually is. This system is
capable of SPL in excess of 120 dB at 1 M from the speaker!
Flying the PR 15D
®
Caution: The suspending or flying of the Peavey PR 15D must be done by a certified structural
engineer.
®
Important Safety Information for Mounting the Peavey PR 15D speaker system
Caution: Before attempting to suspend this model of speaker, consult a certified structural engineer.
Speaker can fall due to improper suspension, resulting in serious injury and property damage. Other
enclosures must not be suspended below one, nor should additional weight be suspended from one of
these units. Use only the correct mating hardware. All associated rigging is the responsibility of others.
Always use all four inserts of a given group as a set, NEVER use just one insert to fly a cabinet! The four
insert groupings are a top group of four and a bottom group of four. Some models also have a group of
four on the rear plane of the cabinet.
Maximum enclosure angle from vertical hang: 30˚
Always use a suitable safety chain or wire rope, looped through the top handle, and firmly attached to a
suitable structural member as indicated by a certified structural engineer.
The recommended range of torque for the mounting bolt is 3 to 3-1/2 lb./feet of torque. DO NOT
OVERTIGHTEN! If an insert spins, it has been damaged and the cabinet cannot be flown!
Never transport the cabinet while mounted on an array bracket or other mounting bracket, as this may
unduly stress the mounting inserts.
WARNING! (note to structural engineer)
®
For the PR 15D, the thread insertion depth of the end of the mounting bolt should not be more than 5/16"
past the surface of the cabinet.
If these thread insertion depths are exceeded, then the inserts may be damaged or unseated from the
cabinet, severely compromising the mounting integrity of the cabinet!
The correct mounting bolt diameter and threads per inch are: 1/4" X 20. Use of a grade five-bolt is
recommended.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Connecting AC Power To The PR 15D
The PR 15D comes with an 8-foot IEC connection AC power cord. If you are using an extension cord or power
strip with this powered speaker, make sure it is of good quality and of a sufficient current capacity to maintain
safety and maximize the power output capability of the PR 15D. Do not connect any other device to the same
extension cord that the PR 15D is connected to.
Special Note for Permanent Installation
When installing the PR 15D, AC power runs will be used and a certified electrician should be consulted to
be sure that all AC wiring complies with local codes and regulations. It is also advisable to use a cable clip
properly affixed to the cabinet to strain relief the IEC power cord connected to the amplifier module at (2)
so the power cord cannot be pulled out or vibrate loose.
use of PR 15D with a Subwoofer
The built-in pole adapter allows use with the Peavey SP Subcompact 18X and the accessory pole that it is
designed to use, Peavey part #00326540.
The pole used is 36-3/16" long and has a nominal diameter of 1-3/8".
Connecting a Signal to the PR 15D
There are a variety of ways to input a signal to the PR 15D.
The primary input (5) provides either a balanced mic- or line-level input, allowing the use of a 1/4" phone
plug, either a standard single-ended (tip-sleeve) plug or a balanced TRS (ring-tip-sleeve) type plug OR a
male XLR plug. Then there are two line-level unbalanced 1/4" phone jacks that can be mixed in with the
primary input.
Do not connect cables to the jacks while the unit is ON and the Volume is turned up!
While a standard single-ended 1/4" phone plug-equipped cable will work well and the balanced input
circuitry of the primary input (5) will provide some interference rejection, a balanced cable using either
the balanced TRS 1/4" phone plug or the XLR plug will provide superior interference rejection and
performance. Sometimes, with difficult interference problems, it will be helpful to lift the shield ground
on a balanced cable at the PR 15D end only by using the ground lift switch (4). Check any input changes
carefully, always turning the volume control down before plugging and unplugging cables.
Use of high quality, premium cables is recommended for the PR 15D, as these usually have better
shielding and materials and will provide greater long-term reliability. It is usually a good idea to leave
some slack at the input to the PR 15D and also to tape the cables down or run them under a cable guard to
avoid anyone tripping over them or pulling the PR 15D over when stand mounted.
Volume Control Adjustment
The PR 15D is equipped with a volume control to facilitate use in many different applications. With the
volume control adjusted fully clockwise, gain is at maximum and the input sensitivity is 0.375 V RMS
for full-rated output. When driving the PR 15D from a mixer, it may be advantageous to reduce the input
sensitivity by turning the volume control to the halfway point. The PR 15D will now more closely match a
typical power amp.
If the mixing board indicates clipping of its output signals, then all of the PR 15P power capability is not
being utilized cleanly. Clipping the signal before it gets to the PR 15D is not optimal. Reduce the mixer
output level and turn up the volume control on the PR 15D.
™
™
The amplifiers in the PR 15D are equipped with DDT and an LED indicator to show that DDT has
engaged. If the sound seems heavily compressed, check this indicator; if it is blinking RED more than
occasionally, then the drive level from the mixer (or the volume control on the PR 15D) needs to be reduced.
®
When first turning on the sound system, switch on all upstream electronics first, then the PR 15P with
its volume control fully counterclockwise (all the way down). Begin checking levels with the mixer output
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
level controls all the way down, and bring them up slowly with the PR 15D volume control set to the
desired setting (halfway up recommended to start).
Mic/Line Pad Adjustment
The mic/line pad (6) provides for the increased gain needed for microphone use into the primary input (5).
Use a straightened paperclip or small screwdriver to reach through the hole in the rear panel where the
recessed tab is to set its position. Set the Mic/Line Pad to “in,” or the white tab furthest from the panel,
for line-level signal use and set it “out,” or closest to the panel, for mic-level use. The unit is shipped with
the tab in the line-level position. It is recessed behind the panel so that the gain can not be inadvertently
increased during transport or set-up.
Due to the 30 dB of extra gain that this switch provides, DO NOT leave it in the “out” position for line-level
use! This will result in input-stage clipping of the PR 15D and cause unnecessary distortion.
TROuBLESHOOTING
No Output at All
First, make sure the unit has AC power and is turned ON. Make sure the Power/Clip LED (4) is illuminated
Green. If not, make certain the ON/OFF switch (3) is in the ON position and check the IEC power cord connection
(2) by ensuring it is fully engaged and seated. Make certain the AC line cord is plugged into a working AC outlet.
Finally, check the fuse (1). (See the Rear Panel: Fuse section, for safety instructions.)
Once assured your unit is getting AC power, check that the PR 15D is getting a signal. Temporarily disconnect
the cable running to its inputs and connect it to some other device capable of reproducing the signal (i.e., a
power amp and speaker). If this produces a signal, make sure that all Volume controls being used have been
turned up to a satisfactory level (one-third to halfway).
If the PR 15D has been subjected to direct sunlight or excessive heat, the built-in thermal protection may have
been triggered. The power/clip LED will be illuminated RED if this is the case. If so, turn off the PR 15D and let it
cool for a sufficient amount of time.
If there is still no output, contact your authorized Peavey dealer or the Peavey International Service Center.
Hum or Buzz
®
If the PR 15D is producing a hum or buzz, this can be AC outlet related. Try plugging the PR 15D into a
different AC outlet. Sometimes, if a different circuit (breaker) is used for the mixer and the PR 15D, it can
cause hum problems.
Ensure that shielded cables have been used to route the signal to the PR 15Ds inputs. If speaker cables with
1/4" plugs are used as input cables instead of shielded cables, they will be prone to hum or buzz.
Hum may be ground loop related. It will be helpful to lift the shield ground on a balanced cable at the PR
15D end only by using the ground lift switch (4). Check any input changes carefully by first turning down the
volume control, plugging and unplugging cables, or lifting the shield ground at the speaker end.
Check to make sure light dimmers are not on the same circuit as the PR 15D, the mixer or any source
devices. If light dimmers are used, then it may be necessary to turn them full ON or full OFF to eliminate or
reduce hum. This is a typical AC wiring/light dimmer interference problem, not a design flaw of the PR 15D.
The third wire (ground plug) on the AC plug should NEVER be removed or broken off.
Distorted or Fuzzy Sound
First, ensure the mixer (signal source) is not clipping or being overdriven. Make sure the volume control/s
(7) and (9) on the PR 15D have not been set too low.
Check that the input plugs are fully seated in the input jacks (5) and (8) on the rear panel of the PR 15D.
Ensure that the proper MIC/LINE PAD setting is being used (6) for line-level signals, or that a power amp
has not been plugged into one of the input jacks of the PR 15D.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
If an extension cord is being used to provide the AC power to the unit, ensure that it is of sufficient current
capacity and that it is not also being used to supply power to any other device.
The PR 15D has built-in EQ to extend and smooth the natural response of the speakers in the system.
Bass boost and HF EQ have been applied and the system has a nominally flat response, so it should
require little, if any, additional EQ. If excessive additional bass boost or HF boost have been added
externally to the PR 15D, it could cause premature overload at high SPL. Reduce the amount of any
external (mixer, rack) EQ and see if that clears up the distortion.
Finally, realize that even though the PR 15D is a powerful and high output unit, it does ultimately have
limits, and it may need additional powered units (or a subwoofer) to provide enough sound output or
coverage. In this case, try turning the mixer levels down a little to see if that clears things up.
If, after checking all the things listed to check and anything else you can think of to check safely, and the
system still exhibits problems, carefully note all conditions and check with your Peavey dealer for advice.
Care and Maintenance
Your PR 15D is a sturdy and durable product and will provide years of reliable use if properly cared for. Use
common sense and read the safety warnings to avoid hazardous operating conditions.
The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing
to qualified service personnel.
Sunlight/Heat
Avoid prolonged exposure to direct sunlight, as this may cause the unit to overheat and thermally shut off.
Excessively hot operating conditions can also cause a thermal shutdown.
Do not store in extremely hot or cold conditions or extremely high humidity. Always allow unit to come to
room temperature before use.
Cleaning
Never clean the PR 15D while plugged in or turned ON! When the unit has been fully disconnected from AC
power sources, use a dry cloth to remove soil or other dirt. Never use strong solvents on the PR 15D, as
they could damage the cabinet. Do not allow ANY fluids to drip inside the PR 15D.
Touchup
For an overall finish enhancement and protective coating, use gloves to apply a plastic finish protector,
®
such as Armor-All protectant, to the surface of the plastic cabinet only. Note that the cabinet will be
slippery after these treatments; rub them down vigorously with a dry, lint-free cloth to minimize this.
Check for Secure Hardware
After the first few months of use and periodically thereafter, check the hardware of the PR 15D for
™
tightness, including the rear panel screws and the screws that hold the baffle and rear cabinet together.
The unit is subject to a great deal of vibration, and this could cause them to loosen with use.
Architectural and Engineering Specifications
The powered loudspeaker system shall have a frequency response from 47 Hz to 20 kHz. The peak SPL
with inaudible distortion shall reach 120 dB with music as a source, when measured at a distance of
1M and driven to full output capacity. The system shall utilize a 15” heavy duty woofer and an RX˛14
compression driver tweeter. The nominal radiation pattern shall be 90˚ in the horizontal plane, and 40˚ in
the vertical plane.
The powered, bi-amplified loudspeaker system shall have a group of medium impedance input connectors
consisting of one combo female XLR and 1/4” TRS phone jack, and two 1/4” phone jacks, on the rear
panel. A volume control will be located near each input jack. The combo female XLR and 1/4” TRS phone
jack will have a gain adjust pad that provides for switching between line-level input signals, and mic-level
input signals.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
The system power amplifiers shall have an unfiltered frequency response of 10 Hz to 30 kHz which deviates
no more than +0, -1 dB up to rated power, a damping factor greater than 100 @ 1 kHz into 8 ohms, hum and
noise better than 90 dB below rated power, and THD and IMD of less than 0.1%. The woofer amplifier shall
be capable of 150 W into a 8 ohm nominal load, and the tweeter amplifier shall be capable of 50 W output
into a 8 ohm load, and both shall incorporate independent DDT™ compression.
The input signal shall be electronically divided into high frequencies and low frequencies by a staggered-
pole third order slope line-level crossover at 2 kHz. The low frequencies shall be processed to provide bass
boost, subsonic filtering and overall response shaping, and the high frequencies shall be equalized for
constant directivity horn EQ- and response-shaping.
The enclosure shall be constructed of injection-molded polypropylene of 1/4" nominal thickness with a UL
flame rating, and reinforcing ribs internally. A handgrip shall be molded-in on the top rear edge, and one
on each side of the woofer.
A powder-coated metal grille shall be provided for woofer protection. The cabinet shall incorporate a pole
mount for speaker stand use, four tall sturdy rubber feet for floor standing use, and four mounting point
inserts on the top and bottom each for flying use.
The outside dimensions shall be: 28.56" tall by x 21.31" wide (11.50" in rear) by x 17.00" deep, and
the weight shall be 37 lbs. Power requirements shall be: 100 Watts nominal, 100 & 120 VAC, 50/60 Hz
Domestic and 220-240 VAC, 50/60 Hz (Export). The loudspeaker system shall be called a Peavey PR 15D.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Peavey PR®15D
SPECIFICATIONS
Crossover Slopes:
Additional Remarks:
Also available as a passively crossed-
over unit, the Peavey PR 15.
Enclosure: Peavey PR 15D
18 dB/octave (third order) low pass,
18 dB/octave (third order) high pass,
both with staggered poles and driver
EQ. Unit has horn spatially aligned
with woofer.
(domestic)
Frequency Response:
47 Hz to 20 kHz
ELECTRONICS AND AMPLIFIER
SPECIFICATIONS:
Low Frequency Limit (-3 dB point):
36 Hz
Electronic Input Impedance
(Nominal): 10 k Ohms unbalanced, 20 k
Ohms balanced line level, 2.4 k Ohms
balanced mic level.
Electronic Input Impedance (Nominal):
Primary balanced input: 20 k Ohms line
level sensitivity selected, 2.4 k Ohms
mic level sensitivity selected, 10 k
Ohms unbalanced 1/4".
useable Low Frequency Limit (-10 dB
point):
42 Hz
Input Connections:
Internal Power Amplifiers (@120
VAC line):
Woofer - 150 Watts @ less than 0.1%
distortion
Tweeter - 70 Watts peak dynamic power
50 Watts @ less than 0.1% distortion.
One combo female XLR/ 1/4" phone
jack providing balanced operation,
with switch selectable mic or line level
sensitivity. Also has two 1/4" phone
jack line level unbalanced input and
output.
Mic Switch Sensitivity Increase:
30 dB
Infrasonic filter protection:
36 dB/octave roll-off
Woofer servo that subtracts error so
that the woofer cone follows the drive
waveform precisely.
Nominal Sensitivity (1W @1M, swept sine
input in anechoic environment):
97 dB
Enclosure Materials and Finish:
Injection-molded polypropylene of a
nominal thickness of 1/4" with internal
ribbing and bracing, and with textured
finish. Molded material is black.
Constant Loudness (Fletcher-Muson)
circuit for accenuating bass and treble
at low listening volume levels.
Maximum Sound Pressure Level:
120 dB music peak
Mounting:
Subwoofer pole-mounting via molded-
in mount, flying via Versamount 70
Nominal Radiation Angles:
90˚ horizontal by 40˚ vertical
Nominal Amplifier Frequency
Response: +0, -1 dB from 10 Hz to 30 kHz
™
and four rubber feet for floor use.
Transducer Complement:
15" heavy duty woofer and RX 14 1.4"
titanium diaphragm compression driver
tweeter
Hum and Noise:
Greater than 90 dB below rated power
™
Dimensions:
28.56" (72.5 cm) tall by 21.31"
(54.1 cm) wide {11.50"/29.2 cm in rear}
by 17.00" (43.2 cm) deep
DDT Dynamic Range:
Greater than 14 dB
Box Tuning Frequency (Fbox):
55 Hz
Optional Accessories:
Impulse 200 Floor Monitor Kit
(FG# 00370480)
THD and IM:
Typically less than 0.1 %
®
Electroacoustic Crossover
Frequency: 2,000 Hz
Damping Factor:
Net Weight:
37 lbs.
Greater than 100 @ 1000 Hz, 8 Ohms
Crossover Type:
Internal Electronic two-way crossover
with CD horn EQ, level matching, bass
boost and subsonic filtering.
Power requirements of Peavey
™
PR 15D System (domestic):
Nominal 110 Watts, 120 VAC, 60 Hz
12
Download from Www.Somanuals.com. All Manuals Search And Download.
FREquENCY RESPONSE CuRVES
Amplitude Response (1m On-Axis)
110
100
90
80
70
60
20
50
100
200
500
1k
2k
5k
10k
20k
Frequency (Hz)
Figure 1
13
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY
Effective Date: september 5, 2007
What This Warranty Covers
Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.
What This Warranty Does Not Cover
The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modification or neglect; (2) dam-
age occurring during shipment; (3) damage caused by repair or service performed by persons not authorized by Peavey; (4) products on which the serial number
has been altered, defaced or removed; (5) products not purchased from an Authorized Peavey Dealer.
Who This Warranty Protects
This Warranty protects only the original retail purchaser of the product.
How Long This Warranty Lasts
The Warranty begins on the date of purchase by the original retail purchaser. The duration of the Warranty is as follows:
Product Category
Duration
Guitars/Basses,Amplifiers, Pre-Amplifiers, Mixers, Electronic
Crossovers and Equalizers
2 years (+ 3 years)*
2 years (+ 1 year)*
2 years (+ 3 years)*
1 year (+ 1 year)*
2 years
Drums
Enclosures
Digital Effect Devices
Microphones
Speaker Components (incl. speakers, baskets, drivers,
diaphragm replacement kits and passive crossovers)
1 year
90 days
Tubes and Meters
Cables
Limited Lifetime
[*Denotes additional warranty period applicable if optional Warranty Registration Card is completed and returned to Peavey by original retail purchaser within 90
days of purchase.]
What Peavey Will Do
We will repair or replace (at Peavey's discretion) products covered by warranty at no charge for labor or materials. If the product or component must be shipped to
Peavey for warranty service, the consumer must pay initial shipping charges. If the repairs are covered by warranty, Peavey will pay the return shipping charges.
How To Get Warranty Service
(1) Take the defective item and your sales receipt or other proof of date of purchase to your Authorized Peavey Dealer or Authorized Peavey Service Center.
OR
(2) Ship the defective item, prepaid, to Peavey Electronics Corporation, International Service Center, 412 Highway 11 & 80 East, Meridian, MS 39301. Include a
detailed description of the problem, together with a copy of your sales receipt or other proof of date of purchase as evidence of warranty coverage. Also provide a
complete return address.
Limitation of Implied Warranties
ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE
LENGTH OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Exclusions of Damages
PEAVEY'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT, AT PEAVEY'S OPTION. IF WE ELECT TO
REPLACE THE PRODUCT, THE REPLACEMENT MAY BE A RECONDITIONED UNIT. PEAVEY SHALL NOT BE LIABLE FOR DAMAGES BASED ON INCONVENIENCE, LOSS OF
USE, LOST PROFITS, LOST SAVINGS, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE, OR ANY OTHER DAMAGES WHETHER INCIDENTAL,
CONSEQUENTIAL OR OTHERWISE, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
ThisWarranty gives you specific legal rights, and you may also have other rights which vary from state to state.
If you have any questions about this warranty or service received or if you need assistance in locating an Authorized Service Center, please contact the Peavey
International Service Center at (601) 483-5365
Features and specifications subject to change without notice.
Logo referenced in Directive 2002/96/EC Annex IV
(OJ(L)37/38,13.02.03 and defined in EN 50419: 2005
The bar is the symbol for marking of new waste and
is applied only to equipment manufactured after
13 August 2005
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and specifications subject to change without notice.
Peavey Electronics Corporation • 5022 Hartley Peavey Drive • Meridian • MS • 39305
©2008
Download from Www.Somanuals.com. All Manuals Search And Download.
|