P E A V E Y E L E C T R O N I C S
SPECS
SP™ 3X
SPECIFICATIONS
Frequency response, 1 meter on-
axis, swept-sine in anechoic
environment:
54 Hz to 17 kHz ( 3 dB)
Usable low frequency limit
(-10 dB point):
47 Hz
Power handling:
Full Range:
500 W continuous
1,000 W program
2,000 W peak
Low Frequency Section:
500 W continuous
1,000 W program
2,000 W peak
Passive Mid/High Frequency Section:
150 W continuous
300 W program
600 W peak
Sound pressure level, 1 Watt,
1 meter in anechoic environment:
Full Range:
99.0 dB SPL, (2.83 V input)
Low Frequency Section:
100.0 dB SPL, (2.83 V input)
Mid/High Frequency Section:
99.0 dB SPL, (2.83 V input)
Transducer complement:
Low Frequency Section:
1x 15 in. woofer, vented
1508-8 HE BWX
Mid Frequency Section:
1x 6.5 in. professional grade mid-
range
High Frequency Section:
1x .875 in. exit/51 mm voice coil
compression driver on CD Horn
RX™22 on a CH®3 CD Horn
Time offset:
Low Frequency:
Mid/High Frequency: 0.0 ms
0.04 ms delay
Impedance (Z):
Full Range:
Nominal:
Minimum:
Low Frequency:
Nominal:
Minimum:
Passive MF/HF:
Nominal:
8.0 Ω
5.4 Ω
Maximum sound pressure level
(1 meter):
Full Range:
126.0 dB SPL continuous
132.0 dB SPL peak
Low Frequency Section:
127.0 dB SPL continuous
133.0 dB SPL peak
8.0 Ω
6.9 Ω
Box tuning frequency:
Low Frequency Section:
8.0 Ω
6.2 Ω
58 Hz
Minimum:
Crossover frequency (internal
passive):
Low Frequency - Mid Frequency:
Input connections:
2x 1/4 in. phone jack and 1x Neutrik®
NL4 Speakon® (bi-amp only)
Passive Mid/High Frequency Section:
120.0 dB SPL continuous
126.0 dB SPL peak
800 Hz
Enclosure materials and finish:
Mid Frequency – High Frequency
2,000 Hz
3/4" OSB finished in black carpet
Radiation angle measured at -6 dB
point of polar response:
90 degrees horizontal by
Mounting provisions:
This unit is not designed for overhead
suspension.
Recommended active crossover
frequency region and slope:
Low Frequency – Mid/High Frequency:
750 Hz at 12 dB/octave
45 degrees vertical
Download from Www.Somanuals.com. All Manuals Search And Download.
built-in, and four large rubber feet on
bottom for floor use.
vertical plane. The outside dimensions
shall be 33.63 inches high by 21.38
inches wide by 22.88 inches deep. The
weight shall be 92 pounds. The
loudspeaker system shall be a Peavey
model SP 3X.
Power Handling
There are many different approaches
to power handling ratings. Peavey rates
this loudspeaker system’s power handling
using a full-range form of the AES
Standard 2-1984. Using audio band 20 Hz
to 20 kHz pink noise with peaks of four
times the RMS level, this strenuous test
signal assures the user that every portion
of this system can withstand today's high
technology music. This rating is contingent
upon having a minimum of 3 dB of
amplifier headroom available.
Architectural and Engineering
Specifications
The loudspeaker system shall have an
operating bandwidth of 54 Hz to 17 kHz.
The nominal output level shall be 99.0 dB
when measured at a distance of one
meter with an input of one Watt. The
nominal impedance shall be 8.0 Ohms.
The maximum continuous power handling
be 500 Watts, maximum program power of
1,000 Watts and a peak power input of at
least 2,000 Watts, with a minimum
3 + 2 YEAR LIMITED WARRANTY
NOTE: For details, refer to the
warranty statement. Copies of
this statement may be obtained
by contacting Peavey Electronics
Corporation, P.O. Box 2898, Meridian,
Mississippi 39301-2898.
Mounting
amplifier headroom of 3 dB. The nominal
radiation geometry shall be 90 degrees in
the horizontal plane and 45 degrees in the
This unit is not designed for overhead
suspension. SA-1 stand mount adapter
SP™ 3X INPUT
Download from Www.Somanuals.com. All Manuals Search And Download.
Features and specifications subject to change without notice.
Peavey Electronics Corporation • 711 A Street • Meridian • MS • 39301
©2001
Printed in the U.S.A. 5/01
Download from Www.Somanuals.com. All Manuals Search And Download.
|