ETHERNET S ETUP GUIDE
The Monarch® 7411™ wireless Ethernet Print Server lets you communicate
with a Monarch® 9855® or 9860™ printer on a 10baseT or 100baseTX wired
Ethernet network or on an 802.11b or 802.11g wireless network. The print
server operates in Ad-Hoc (peer-to-peer) mode or infrastructure (access
point) wireless mode. You can also remotely manage and download print
batches, formats, printer configurations, and fonts. MonarchNet2™ software
is available on your printer for a licensing fee. Contact your sales
representative for more information about MonarchNet2, or visit our Web
The print server supports multiple network protocols for users with
Telnet/FTP, Microsoft® Windows® 98, 2000, NT®, XP, and Vista™, TCP/IP
(including LPR/LPD, Bootp, DHCP, and HP JetDirect™), Novell® NetWare®
and SNMP. All protocols are simultaneously active.
Note: When turning on the printer or after sending a ^PR (printer reset)
immediate command, wait at least 30 seconds before sending data
to the print server. Any data sent to the print server before the
30-second interval may be lost.
Se tting Up the Print Se rve r
From the Main menu, select Setup, Port Settings, then Parallel Comm.
Then, follow these steps:
1. Press ꢀor ꢁuntil you see
PARALLEL COMM
Port ꢁ
2. Press Enter/Pause. Press ꢀor ꢁuntil you see
PORT
ꢀ
Internal
Paxar® is a trademark of Paxar Corporation.
Monarch®, MonarchNet2, 7411, and 9855® and 9860 are trademarks of Paxar Americas, Inc. a subsidiary
of Avery Dennison Corp. Avery Dennison® is a trademark of Avery Dennison Corp.
Microsoft, Windows, and NT are trademarks of Microsoft Corporation.
Novell and NetWare are trademarks of Novell, Inc.
HP Jet Admin and HP Web Jet Admin are trademarks of Hewlett-Packard, Inc.
Other products are trademarks or registered trademarks of their respective
companies and are hereby acknowledged.
TC7411MN2SG Rev. AC 12/07
©2006 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp.
All rights reserved. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
When the printer is turned on, the print server runs through a set of power-up
diagnostics for a few seconds. All three LEDs blink momentarily, then indicate the
following activity:
LED Indicators
Status
solid
blinking
off
printer is on
Orange
error
printer is off
solid
blinking
off
Ethernet link (wired 10baseT)
network activity
Yellow
no Ethernet connection
Ethernet link (wired 100baseTX)
network activity
solid
blinking
off
Green
no Ethernet connection
wireless link
solid
blinking
off
Yellow & Green
network activity
no wireless connection
If using network version CTMO-xxx (limited quantity produced), two LEDs indicate
the following activity:
LED Indicators
Status
device ready
Ethernet link
wireless link
network activity
error
solid
Green
blinking
blinking
Orange
Print a configuration label to verify which print server you have.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the Print Se rve r
1. Start your Web browser.
2. Type in your printer’s IP address (for example, 192.0.0.192) on your
computer and press Enter/Pause on the printer. If you are not sure of
your printer’s IP address, print a configuration label.
The printer’s display shows the “N” network symbol or the antenna
symbol when the printer is connected and ready to receive data.
Note: A MonarchNet2 manual is available and included in the licensing
fee. Contact your sales representative for more information.
Printing a Configura tion La be l
To print a configuration label, press the Test button (if available) on the
back of the Ethernet print server unit.
MonarchNet 2 Network Status
Connected – Wireless
MAC – 00-33-22-AK-35-18
Nwk Ver – CTMO – 7.011 (2006.4.12)
Boot Ver – 7.6
Note: Use 6-inch long supply.
If you are using supply that
is shorter than 6 inches long,
temporarily change your
Supply Type in the printer
menu to “continuous” to print
the entire test label. After
printing the test label,
WiFi Ver – 1F 1.4.9
Prn Ver – Version 3.0
Boot Ver – Version 3.1
Network
Version
IP Address
192.0.192.0
Subnet Mask
IP Gateway
255.255.0.0
192.0.192.0
change your supply type to
your previous setting. Some
information may print outside
the label edges of narrow
supply.
(via DHCP 192.0.192.10)
IP Address
Boot Method
Boot Tries
Timeout
AUTO
3
0 min
1 min
Keep Alive
WiFi Information
WiFi SSID
WiFi Mode
ABC123
INFRASTRUCTURE
11
WiFi Speed
WiFi WEP
Disabled
Signal Strength
Actual SSID
Attached AP Mac
72
Network Stats
Packets Received 2485
Bytes Received 225990
Bad Packets Received
Receiver Overruns 0
448
193
Packets Transmitted
Bytes Transmitted 23731
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|