899223 - 05-31-01.qxd 2/19/02 2:00 PM Page 1
ESPAÑOL: PÁGINA 13
FRANÇAISE : PAGE 25
Instruction
manual
FLOORING CLEAT
NAILER
MODEL FCN200
Patent No: 6,155,472
IMPORTANT
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
To learn more about Porter-Cable
visit our website at:
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No._______________________________________
Copyright © 2001 Porter-Cable Corporation
Part No. 899223 (015)
Download from Www.Somanuals.com. All Manuals Search And Download.
899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 3
9. DISCONNECT TOOL FROM AIR
SUPPLY HOSE before doing tool
maintenance, clearing a jammed fastener,
leaving work area, moving tool to another
location, handing the tool to another
person, or making adjustments. Fig. 5.
Fig. 5
10. NEVER USE A TOOL that is leaking
air, has missing or damaged parts, or
requires repair. Make sure all screws and
caps are securely tightened.
Fig. 6
11. NEVER USE TOOL IF TRIGGER
mechanism is inoperable, missing or
damaged. Do not alter or remove trigger
mechanism. Make daily inspections for free
movement of trigger mechanism.
12. DO NOT USE TOOL WITHOUT
SAFETY WARNING LABEL. If label is
missing, damaged or unreadable, contact
your Porter-Cable Service Center for a
replacement. Fig. 6.
Fig. 7
2
13. ONLY USE PARTS, FASTENERS,
AND ACCESSORIES recommended by
Porter-Cable.
1
Fig. 8
14. REMOVE ALL FASTENERS from tool
before connecting to air supply. The tool’s
driving mechanism may cycle when tool is
connected to the air supply. Fig. 7.
15. ALWAYS ASSUME THE TOOL
CONTAINS FASTENERS. Keep the tool
pointed away from yourself and others at all
times. No horseplay. Respect the tool as a
working implement. Fig. 8.
16. DO NOT LOAD FASTENERS with
trigger depressed, to prevent unintentional
firing of a fastener. Fig. 9.
Fig. 9
3
Download from Www.Somanuals.com. All Manuals Search And Download.
899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 4
17. REMOVE FINGER FROM TRIGGER
when not driving fasteners. Never carry tool
with finger on trigger: tool will fire a fastener
if rubber cap is bumped while trigger is
depressed. Fig. 10.
Fig. 10
18. USE THE MALLET TO RACK THE
WOOD STRIP, NOT THE NAILER. Fig. 11.
19. DO NOT USE THE METAL END OF
THE MALLET TO STRIKE THE PLUNGER,
use the rubber capped end only.
20. FIRE FASTENERS INTO WORK
SURFACE ONLY: never into materials too
hard to penetrate.
Fig. 11
21. DO NOT USE THE NAILER TO
POSITION the flooring strips. Hitting the
rubber cap without first activating the trigger
will cause severe internal damage to the
Nailer. Fig.12.
22. THE TRIGGER IS A SAFETY DEVICE
and should only be pulled when the Nailer is
in proper position on the work surface and
before the rubber cap is struck with the
mallet. Do not tie or tape down the safety
trigger as the Nailer could discharge if
dropped on the rubber cap. The Nailer will
not fire unless the trigger is pulled before the
mallet blow. Fig.13.
Fig. 12
23. DO NOT DRIVE FASTENERS on top of
other fasteners: the fasteners can ricochet
causing personal injury.
Fig. 13
4
Download from Www.Somanuals.com. All Manuals Search And Download.
899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 5
EMPLOYER’S RESPONSIBILITIES
WARNING: Employer must enforce compliance with the safety warnings
and all other instructions contained in this manual.
Keep this manual available for use by all people assigned to use this tool.
For personal safety and proper operation of this tool, read and follow all of
these instructions carefully.
OPERATING INSTRUCTIONS
FOREWORD
Porter-Cable Model FCN200 is a heavy duty, pneumatic flooring cleat nailer.
It is designed to install tongue and groove hardwood flooring with L-shaped
1
flooring cleats. Flooring in thicknesses of /2" and 25/32" can be installed using
1-1/2" and 2" length flooring cleats respectively. See ACCESSORIES Listing in
back of this manual.
CAUTION: Use approved Porter-Cable flooring cleats only. Porter-Cable
flooring cleats are made with special design features with superior holding
strength. See ACCESSORIES Listing in back of this manual.
POWER SOURCE
This tool is designed to operate on clean, dry, compressed air at regulated
pressures between 70 and 100 PSI (Pounds per Square Inch)( 4.8 to 6.9 Bar).
The preferred system would include a filter, a pressure regulator, and an
automatic oiler located as close to the tool as possible (within 15 feet is ideal).
All compressed air contains moisture and other contaminates that are
detrimental to internal components of the tool. An air line filter will remove
most of these contaminates and significantly prolong the life of the tool. If an
in-line oiler is not available: place 10 to 15 drops of Porter-Cable Air Tool Oil
(see ACCESSORIES), into the tool’s air inlet at the beginning of each workday.
IMPORTANT: Do not over lubricate the Nailer, excess oil mist or drops
will be vented with spent air when over lubricated. Excess oil could stain
the wood flooring, walls or furnishings. Dry fire the Nailer, without nails, to
purge excess oil, before you begin nailing.
1
3
The tool is equipped with a
/
4" male “quick connector”. A
/8" male “quick
connector” is available from Porter-Cable and may be used in situations where
1
a
/4" supply line is not available. The tool must always be connected to the air
supply with a coupling such that all pressure is removed from the tool when the
coupling is disconnected.
WARNING: All air line components (hoses, connectors, filters, regulators,
etc.) must have a minimum working pressure rating of at least150 PSI (10.3
BAR) or 150% of maximum system potential, whichever is higher.
Do not connect this tool to a system with maximum potential pressure
greater than 200 PSI, (13.8 BAR).
Only connect tool to air supply with a coupling that will release all
pressure from the tool when disconnected.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 6
Disconnect tool from air supply before performing maintenance,
clearing a jammed fastener, leaving work area, moving tool to
another location, handing the tool to another person, or making
adjustments.
PREPARING THE TOOL
1. After reading and understanding this entire manual, connect tool to air
supply (see Fig. 15).
WARNING: Keep tool pointed away from yourself and others at all
times.
Always connect tool to air supply before loading fasteners. Do not
load fasteners with trigger depressed.
Use only approved Porter-Cable fasteners (see ACCESSORIES).
Always wear Z87.1 approved safety glasses, and hearing protection
when preparing or operating the tool.
Never use a tool that leaks air or needs repair.
2. Orient a strip of L-shaped cleats with points down (see Fig. 16), and align
with the slot (L) at the end of the magazine.
3. Feed the strip of cleats into the magazine
4. Pull the follower (B) Fig. 17, all the way to the rear of the magazine and
release. The follower will apply pressure to the strip of cleats to feed it into
the driving mechanism.
Fig. 16
Fig. 15
“L”
B
C
B
Fig. 17
Fig. 18
6
Download from Www.Somanuals.com. All Manuals Search And Download.
899223 - 05-31-01.qxd 2/19/02 2:01 PM Page 7
USING THE TOOL
Complete all steps of PREPARING THE TOOL before using the tool.
First position and closely fit together (rack) the flooring strip with the (metal)
mallet. Position the tool on the tongued edge of the flooring strip (see Fig. 18)
aligning the driver guide against the front of the flooring strip. Pull and hold
the trigger and strike the rubber cap with the rubber mallet. The tool will then
drive the cleat at the correct 45 degree angle as shown in Fig. 19 and 20. The
proper length of flooring cleat to use with various thicknesses of flooring is
also shown in Fig. 19 and 20.
Fig.20
Fig. 19
It is not necessary to hit the rubber cap hard to activate it. Never hit the tool
hard with excessive force, as this will damage the tool.
DO NOT USE THE NAILER TO POSITION the flooring strips. Hitting the
rubber cap without first activating the trigger will cause severe internal
damage to the Nailer.
DO NOT USE THE METAL END OF THE MALLET TO STRIKE THE RUBBER
CAP, use the rubber end only.
WARNING: The trigger is a safety device and should only be pulled
when the tool is in the proper position on the work surface and
before the rubber cap is struck with the mallet. Do not tie or tape
down the safety trigger as the tool could discharge if dropped on the
rubber cap. The tool will not fire unless the safety trigger is pulled
before the mallet blow.
NOTE: When Using Tool to install Pre-finished Flooring
The Porter-Cable FCN200 was designed for installing both
unfinished and pre-finished hardwood flooring. Care must be used
however when installing pre-finished flooring to ensure that the finish
is not damaged by the tool. It is recommended that the tool be
inspected for damage [especially the base plate (C) Fig.18] and
tested on a sample section to be certain that the tool and technique
of use do not mar the finish. This procedure should be followed
before each job due to variations in flooring and tool condition.
WARNING: Remove finger from trigger when not driving fasteners.
Never carry tool with finger on trigger: tool will fire a fastener if
rubber cap is bumped.
WARNING: Keep tool pointed in a safe direction at all times.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 8
WARNING: Never attempt to drive a fastener into material that is
too hard. The fastener can ricochet causing personal injury.
WARNING: Disconnect tool from air supply before performing
maintenance, clearing a jammed fastener, leaving work area, moving
tool to another location, handing the tool to another person, making
adjustments.
WARNING: Clean and inspect tool daily. Carefully check for proper
operation of trigger mechanism. Do Not use the tool unless the
trigger mechanism is functional. Do Not use if the tool is leaking air
or needs any other repair.
CLEARING A JAMMED FASTENER
1. CAUTION: Disconnect tool from air supply.
2. Remove any remaining fasteners from the nailer.
A. Pull pusher back by pulling front knob (A) Fig. 21. This will retract the
pusher face from the cleat strip.
B. Still using the front knob (A) Fig. 22, slide the pusher to the front
bypassing the cleat strip.
C. Slide the remaining Fasteners out of the magazine. Fig. 23.
3. Use the 3/16” hex wrench to remove the three screws (A) Fig. 24
attaching the Driver Guide Plate and Gate (B) Fig. 24.
4. Slide out the Driver Guide Plate and Gate assembly. Fig. 25.
5. Pull the Driver Guide Plate and Gate assembly apart and remove the
jammed Fastener. Fig. 26.
6. Replace the Driver Guide Plate and Gate with three screws.
Fig. 22
Fig. 21
A
A
Fig. 23
Fig. 24
A
B
8
Download from Www.Somanuals.com. All Manuals Search And Download.
899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 9
Fig. 26
Fig. 25
MAINTENANCE
CLEAN AND INSPECT DAILY
CAUTION: Disconnect tool from air supply before cleaning and
inspection. Correct all problems before placing the tool back in use.
Wipe tool clean and inspect for wear or damage. Use non-flammable
cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK
tool with cleaning solutions. Such solutions can damage internal parts.
Inspect trigger mechanism to insure system is complete and functional: no
loose or missing parts, no binding or sticking parts.
Keep all screws tight. Loose screws can cause personal injury or damage
tool.
If tool is used without an in-line oiler: place 10 to 15 drops of Porter-Cable
Air Tool Oil into the air inlet of the tool at the beginning of each workday.
IMPORTANT: Do not over lubricate the Nailer, excess oil mist or drops
will be vented with spent air when over lubricated. Excess oil could stain
the wood flooring, walls or furnishings. Dry fire the Nailer, without nails, to
purge excess oil, before you begin nailing.
SERVICE AND REPAIRS
All quality tools eventually require servicing or replacement of parts due to
wear from normal use. Some user serviceable components are described in
the TROUBLESHOOTING Section. Complete product Service is available
from either an AUTHORIZED PORTER-CABLE SERVICE STATION or a
PORTER-CABLE/DELTA FACTORY SERVICE CENTER. All repairs made by
these agencies are fully guaranteed against defective material and
workmanship. We cannot guarantee repairs made or attempted by anyone
other than these agencies.
Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 10
TROUBLESHOOTING
CAUTION: Disconnect tool from air supply before performing any
Service Procedure.
SYMPTOM
PROBLEMS
SOLUTIONS
1. Air leak near top of
tool or in trigger area.
Loose screws.
Worn or damaged
o-rings or seals.
Tighten screws.
Install “OVERHAUL” Maintenance Kit.
2. Tool does nothing or
operates sluggishly.
Inadequate air supply.
Inadequate lubrication.
Worn or damaged
o-rings or seals.
Verify adequate air supply.
Put 10 to 15 drops of oil into air inlet.
Install “DRIVER” Maintenance Kit.
Install “OVERHAUL” Maintenance Kit.
3. Air leak near bottom
of tool.
Loose screws.
Worn or damaged
o-rings or bumper.
Tighten screws.
Install “OVERHAUL” Maintenance Kit.
4. Tool jams frequently.
Incorrect fasteners.
Verify approved fasteners of
correct size.
Damaged fasteners.
Magazine or nose
Replace w/undamaged fasteners.
Tighten screws.
screws loose.
Magazine is dirty.
Clean magazine.
Pusher spring damaged.
Driver is worn or damaged.
Replace spring.
Install “DRIVER” Maintenance Kit.
5. Other.
Contact a Porter-Cable
Service Facility.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 11
ACCESSORIES
A complete line of accessories is available from your Porter-Cable ·
Delta Supplier, Porter-Cable · Delta Factory Service Centers, and
Porter-Cable Authorized Service Stations. Please visit our Web Site
www.porter-cable.com for a catalog or for the name of your nearest
supplier.
WARNING: Since accessories, other than those offered by Porter-Cable
· Delta, have not been tested with this product, use of such accessories
could be hazardous. For safest operation, only Porter-Cable ·Delta
recommended accessories should be used with this product.
CATALOG NO.
DESCRIPTION
LENGTH QUAN/BOX
FLC150
FLC200
Flooring Cleat Nails
Flooring Cleat Nails
1-1/2"
1000
2"
1000
60076
60077
48248
Overhaul Kit
Driver Kit
Wrench Allen 3/16”
48245
884293
899226
Wrench Allen 5/32”
Oil (for Air Tools)
Mallet
11
Download from Www.Somanuals.com. All Manuals Search And Download.
899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 12
PORTER-CABLE LIMITED ONE YEAR WARRANTY
Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station. Proof
of purchase may be required. This warranty does not apply to o-rings and driver blades or to repair or
replacement required due to misuse, abuse, normal wear and tear or repairs attempted or made by
other than our Service Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE OF
PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION, 4825
Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY AND
UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary from
state to state.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
899223 - 05-31-01.qxd 2/19/02 2:02 PM Page 36
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
•
Delta Power Tools are Available at These Locations
•
Delta)
MINNESOTA
Cleveland 44125
ARIZONA
ILLINOIS
Addison 60101 (Chicago)
311 Laura Drive
Phone: (630) 628-6100
Fax: (630) 628-0023
Minneapolis 55429
4315 68th Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
8001 Sweet Valley Drive Unit #19
Phone: (216) 447-9030
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Fax: (216) 447-3097
Phone: (602) 437-1200
Fax: (602) 437-2200
OREGON
Portland 97230
4916 NE 122 nd Ave.
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
MISSOURI
North Kansas City 64116
1141 Swift Avenue
P.O. Box 12393
Phone: (816) 221-2070
Fax: (816) 221-2897
CALIFORNIA
Phone: (503) 252-0107
Fax: (503) 252-2123
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
MARYLAND
PENNSYLVANIA
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
St. Louis 63119
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
MASSACHUSETTS
Braintree 02185 (Boston)
719 Granite Street
TEXAS
NEW YORK
FLORIDA
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (781) 848-9810
Fax: (781) 848-6759
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
Phone: (954) 321-6635
Fax: (954) 321-6638
NORTH CAROLINA
Charlotte 28270
Houston 77055
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: (713) 682-0334
Fax: (713) 682-4867
Tampa 33609
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
OHIO
WASHINGTON
GEORGIA
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Renton 98055 (Seattle)
268 Southwest 43rd Street
Phone: (425) 251-6680
Fax: (425) 251-9337
Forest Park 30297 (Atlanta)
5442 Frontage Road, Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts
and accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized
Service Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will
be directed to the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en
muchas grandes ciudades. Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los
accesorios para los productos Porter-Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable
Delta, Centro de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas
opciones, llame al 888-848-5175 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service
agréés sont situés dans beaucoup de grandes villes. Appelez au 800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en
repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-Cable Delta, s’adresser à tout distributeur Porter-Cable
Delta, centre de service agréé ou centre de service d’usine Porter-Cable Delta. Si vous n’avez accès à aucun de ces centres, appeler le
888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable Delta le plus proche.
•
•
•
•
•
•
•
•
•
•
•
•
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
QUÉBEC
ALBERTA
MANITOBA
1515 Ave.
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
ONTARIO
1447, Begin
St-Laurent, (Montréal), Québec
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 836-2840
Fax: (519) 767-4131
The following are trademarks of PORTER-CABLE
•
DELTA (Las siguientes son marcas registradas de PORTER-CABLE
•
DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE
•
DELTA): BAMMER®, LASERLOC®, OMNIJIG®, POCKET
CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®, QUICKSAND®, SANDTRAP®, SAW BOSS®, SPEED-BLOC®, SPEEDMATIC®,
SPEEDTRONIC®, STAIR-EASE®, THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, TIGER CUB®, TIGER SAW®, TORQ-BUSTER®,
VERSA-PLANE®, WHISPER SERIES®, DURATRONIC™, FRAME SAW™, INNOVATION THAT WORKS™, JETSTREAM™, MICRO-SET™,
MORTEN™, NETWORK™, RIPTIDE™, TRU-MATCH™, WOODWORKER’S CHOICE™.
Trademarks noted with ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países. Marques déposées, indiquées par la lettre ®, sont déposées au Bureau des brevets d’invention et marques
déposées aux Etats-Unis et pourraient être déposées aux autres pays.
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|