Cantilever Bracket
Multifunctional double deck wall mount
INSTALLATION GUIDE
Item No.:PSW115
Easy installing: Just hang up the display
Safety: locking by spinning bolt on the bottom
Max load capacity:40kg(88lbs)
TV size range: 17"~32"
Adjustable angle: -5 ~15 (tilt), 90 (Roll control)
-8-
IMPORTANT: If don’t understand about right install ways, please
consult to normal installing specialist.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Attach mount to wall
WARNING
First, determine the height of stand
The best height of stand is parallel to eyelevel of a person who sitting on a couch.
Normally, the horizontal distance of eyelevel is about 4’ from ground level.
The following two conditions are for determining the perfect height of stand:
1) the distance between wall and couch(Fig 2a).
We are not responsible for any personal injury or product damage due to mishandling,
incorrect mounting, incorrect assembly or incorrect use of this product.
2) the distance of eyelevel from ground level plus the distance measured from
eyelevel of a person sitting on couch with viewing angle of 15°(Fig 2a).
Note: The supplied wall mounting hardware is not for use on steel stud walls or cold
cinder block walls. If you are uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware you required is not included please contact your
local hardware store.
For example:
1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’
2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’
3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’
The perfect height of stand centre will be anywhere within b, where you feel
comfortable for viewing.
Step 1: Attach bracket to TV
Check your TV manual to confirm the diameter of bolt to be used or choose a
appropriate bolts according to size, height and position of the holes on your TV. See
pages 4-5 of these instructions for examples.
15 degree
viewing angle
b
For correct installing, make sure that hook of every bracket must facing down. Use
selected bolt, spacers and washer for installing bracket at the back of display.
Adjust two brackets to equal heights and level. Once aligned, tighten up the
bolts securely.
eyelevel
IMPORTANT: Don't force the bolt into the hole, which will cause a damage of
equipments and injure of person. Don't use electric drill to fasten any bolts.
a
Fig 2a
After determining the height of stand, follow the installation instructions in below
to install wall mount to different kinds of wall -wooden, brick, concrete and stone.
Wooden wall((Fig 2b):
Using a awl or nail to make where the nails are located, as shown as fig.2b. Pre-drill
these holes with a 5mm drill bit to at least 80mm in deep hole. Please make sure these
holes are level and located at center. Use wall mount as a template to mark the location
of other three holes and drill the same holes. Fix the wall mount to the wall with 4 long
bolts(I) and washers(K).
-3-
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
Following examples shows how to use bolts, spacers and square washers.
2. Some displays have curved backs with
recessed mounting lands(Fig.a). It will
require the use of spacer. For this display,
install a 9/16” spacer(L) between display and
the bracket. As shown in Fig 1b.
1.Some displays have vertical backs. No spacer is required. Install the bracket directly
to the back of display by using bolts and square washers provided. As shown in Fig.1a.
Fig a
M4 Fig bit
M5 Fig bit
M4 Fig bit
M5 Fig bit
L
H
L
A
D
2
3
H
3
2
B
E
H
H
M6 Fig bit
3
2
H
G
C
H
L
H
F
3
M6Fig bit
1/4"-20 5/8" Fig bit
Fig 1a
Fig 1b
-5-
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
|