1
Download from Www.Somanuals.com. All Manuals Search And Download.
1. INSTALLATION GUIDE
1. On a towel or soft cloth, gently place the monitor unit "facedown" on a
stable work surface.
2. Locate the pigtail with the DIN connector.
3. Connect the DIN connector to the interface cable provided.
4. Connect the RED wire to the positive (+) battery terminal.
5. Connect the Black wire to a chassis electrical ground point.
6. Connect the cable with YELLOW RCA jack to Video Input sources for
your Video Program material.
7. Connect the cable with RED and WHITE RCA jacks to Audio sources for
your Audio Program material.
8. Dome Light Circuit: (NOT SHOWN IN PICTURE) Connect the Black to
Ground. Connect one red lead to the dome light circuit that is positive (+)
when the door is open. Connect the other red lead to a constant positive (+).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. FUNCTION KEYS
2.1 FRONT PANEL FUNCTIONS
POWER: 1. Press the "POWER" button once, it will be "POWER ON."
Press it again, it will be "POWER OFF."
MENU: 1. Pop up the OSD menus. Press the "Menu" button again to
enter the OSD menus. When in sub-menu, press.
"EXIT" to go back to the main menu.
UP/DN: 1. Press the "UP/DOWN" key to increase or decrease value
2. Make item selection in OSD menus to increase or decrease
parameters as well..
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 FUNCTIONS OF REMOTE CONTROL
Brightness:
Contrast:
→ adjust Brightness.
→ adjust Contrast.
Display adjust: → Sharpness hue, saturation adjustment
OSD display: → OSD adjustment and display methods
Input select:
Audio:
Recall:
Exit:
→ Switch between AV1 and AV2 Inputs.
→ Mutes the Audio Signal
→ Return to the main menu
→ Exit’s the menu
Press the "Menu key", to display a crosswise bar with digits. Use the
INC/DEC keys to adjust the value, and then press the "Menu key" to confirm
the adjustment. To have the crosswise bar and digits disappear; press "Exit" to
leave the OSD function directly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. TROUBLE SHOOTING
3.1 NO POWER
1. Make sure the power cable has been pluged in.
2. Make sure the plug has 12V~14V, may use another electrical appliance
to test it.
3.2 NO FUNCTION OF REMOTE CONTROL
1. Make sure the batteries are in good condition and installed properly.
2. Make sure the remote control is aiming at the receiver, and there are no
obstacles in between.
3. Perhaps, it is too far away from the receiver. Normal distance is within 7
meters.
3.2 NO DISPLAY OR NOT CLEAR
1. Check the video signal wires if they are connected properly.
2. Check the antenna or adjust it.
3. Make sure the TV/Video being in proper position.
4. ACCESSORIES
PS2/CAR CABLE
INSTALLATION BRACKET
USER MANUAL
SCREW PACK
REMOTE CONTROL
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. SPECIFICATIONS
ITEM
LCD Panel
DESCRIPTION
14.1" TFT
Active Area:
Resolution:
285.7 (W) x 214.3 (H) mm
1024(H) x 3(RGB) x 768(V)
262,144 colors
0.279 (H) x 0.279 (V) mm
CCFL Side-light type (four lamp)
300 : 1
Display Colors:
Pixel Pitch (mm):
Backlight Unit:
Contrast Ratio:
Brightness (cd/m2):
Viewing Angle:
300
Horizontal:63O (typ.,Lift side), 63O (typ.,right
side)
Vertical: 45O (typ.,up side), 30O (typ.,down side)
DC12V + 10% less than 2A
Yes
Power Supply:
IR Transmitter:
Power management:
24W power consumption (typ.), less than 3W
when in backlight sleep mode.
Power on/off, OSD control
1. Auto detection between NTSC/PAL
2. Sceam is available
User's Control:
System:
Dimensional Outline (mm): 338.0mm (W) x 340.2mm (H) x 52mm (D)
Weight
3.8 kg
Safety Certifications:
UL, FCC, CE, TUV
Operation Temp.:0~50 degree C
Storage Temp.: -20~60 degree C
Humidity: 10~90%
Environmental Condition:
* Recommend for use with PYLE'S PLVWH1 wireless headphones.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|