TURBOPOWER® GAS/OIL ꢃ PACKAGED WATER HEATER
POLYSHIELD® POLYMER-LINED STORAGE TANK
TANK SERIES 900 GALLONS
Blower
Motor
Recovery gph ꢀ
Dimensions (inches)
Min. Inlet Flow
Gas Pressure
"W.C. ꢂ
Shipping
Weight
lbs
Model
Number
Input
Btu/h
#2 Oil
gph
Volt/Ph/
Amps
40°- 120°F 40°- 140°F
A
B
C
J ꢁ
HP
750 P 900A-TPGO
1000 P 900A-TPGO
1250 P 900A-TPGO
1500 P 900A-TPGO
2000 P 900A-TPGO
2500 P 900A-TPGO
750
1000
1250
1500
2000
2500
600
800
600,000
800,000
4.5
6.0
7.5
7.5
6.5
8.0
4.3
5.7
46
46
46
46
60
60
6
8
1
31
31
31
31
36
36
1/2
1/2
3/4
1
3320
3360
3450
3530
3740
3860
115/1∅/10
115/1∅/10
115/1∅/14
115/1∅/16
115/1/∅24
115/1∅/24
1
1
1000
1200
1600
2000
1,000,000
1,200,000
1,600,000
2,000,000
7.2
8
8.6
8
1-1/4
2
11.4
14.3
10
10
2
2
2
ꢀ Recoveries based on 83% thermal efficiency. ASHRAE 90.1 compliant for efficiency and standby loss.
ꢁ "J" dimension is for the burner housing only. Gas train may exceed this dimension.
ꢂ Standard gas train.
*
The information presented is for Natural gas 0.6 S.G.— For operation with propane (LP gas), consult factory.
Dimensions are in inches unless otherwise specified.
Higher inputs available. Consult the factory.
For standard and optional equipment, see form PV 6047.
* REAR ACCESS MODULE
* GAS PRESSURE REQUIREMENTS
MODEL PREFIX
750-1500
M
L
STD or OPTIONAL
OPTIONAL
SEE TABLE FOR MINIMUM PRESSURE BY MODEL NUMBER.
MAXIMUM STATIC INLET PRESSURE: 14" W.C.
23"
23"
8"
8"
FOR PRESSURES OTHER THAN LISTED, CONSULT FACTORY.
2000-2500
STANDARD
Pressure shown is for standard UL gas train. Additional controls
may increase pressure requirements.
STANDARD ELECTRICAL REQUIREMENTS
VENTING REQUIREMENTS
CONTROL VOLTAGE: 120V, 1Ø, 60 HZ., 2 AMPS.
MOTOR VOLTAGE:
-.02" TO -.06" W.C. (NEGATIVE PRESSURE)
208V, 230V, AND 460V MOTORS ARE AVAILABLE BUT WILL
REQUIRE A SEPARATE 120V/2 amps CONTROL CIRCUIT OR AN
OPTIONAL CONTROL CIRCUIT TRANSFORMER.
ENTIRE VENT SYSTEM SHOULD NEVER BE SIZED BASED
UPON THE VENT CONNECTION DIAMETER EXCLUSIVELY.
FOR PROPER SIZING, CONSULT
THE NATIONAL FUEL GAS CODE UNDER “FAN-ASSISTED.”
PVI RESERVES THE RIGHT TO CHANGE THE DESIGN
AND SPECIFICATION WITHOUT NOTICE.
PVI INDUSTRIES, LLC
FORT WORTH, TEXAS 76111
Product is patented in the U.S., Canada, and Mexico.
PV 5480 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
|