Jiva TP/LT – 5815
Touch / LCD POS Terminal
w/ Slim or Universal Base
User’s Manual
Rev.: B2
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technologies, Inc. expressly
disclaims any warranties, expressed, implied or statutory, including without limitation
implied warranties of merchantability or fitness for particular purpose, good title and
against infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technologies, Inc. the publisher of this documentation.
© Copyright Posiflex Technologies, Inc. 2007
All brand and product names and trademarks are the property of their respective holders.
Part 1
P/N: 16280900030
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
PRODUCT PICTURES
Front Views
1
3
4
5
6
1
2
4
7
2
Slim Base Models
Universal Base Models
Universal Base Models
9
8
8
9
10
10
5
7
Slim Base Models
Side Views
11
12
10
5
11
12
10
7
Universal Base Models
Slim Base Models
1
1
12
13
7
13
5
Slim Base Models
Universal Base Models
Part 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Views
1
11
12
8
1
7
5
14
15
10
14
10
16
16
16
16
17
Slim Base Models
Universal Base Models
Bottom Views
20
21
18
20
21
19
19
19
17
Slim Base 3.5” HDD
Universal Base 3.5” HDD
16
22
23
21
24
19
21
20
20
Slim Base 2.5” HDD
Universal Base 2.5” HDD
PARTS IDENTIFICATION
1. Main unit
2. Touch panel / LCD panel
3. Optional side mount kit
4. Power status indicator
5. Universal base stand
6. Optional CDROM drive
7. Slim base stand
8. Cable cover
9. Removal hollow in cable cover
10. Lock / release lever for tilt angle adjust
Part 4
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Optional rear top mount kit PD-302
12. Lock / release button for main unit detach
13. Power switch
14. Rear connect cover
15. Power connector hole
16. Cable exit
17. 2nd cable exit
18. Auxiliary cable exit
19. Rubber feet
20. Bottom plate
21. Bottom plate fixing screw
22. 2.5” HDD window
23. 2.5” HDD bracket cover
24. 2.5” HDD bracket fixing screw
PRODUCT FEATURES
Standard Features:
a) CPU: C3 - 1.0 GHz.
b) An advanced slim or universal base design. The slim base models
support 2nd LCD display or pole mount customer display, storage room
for HDD and optional UPS battery in desktop mount application. The
universal base models support extensive features as 2nd LCD display or
pole mount customer display, storage room for power adaptor, HDD,
optional internal CD ROM drive and optional UPS battery in desktop
mount application. Also possible to be without base but with wall
mount bracket for wall mount application.
c) Support Win 2000, Win XP Pro, WEPOS and Linux environment
d) Fan control software in preloaded OS
e) High quality 15” TFT active matrix LCD panel
f) Vertical type LCD panel with easy tilt angle adjustment from 15° to
72.5°
g) Durable USB interface resistive type (leading edge Infra Red type
optional) touch panel that endures 35 million touches min. at same spot
h) Spill proof water resistant structure allowing easy cleaning
i) Easy maintenance construction
j) Various I/O ports supported, including:
1. one PS/2 KB port
2. one PS/2 mouse port
3. 4 serial ports (3 ports usable if IR touch used). All with capability
for +5V DC support by internal jumper setting change
4. one parallel port
Part 5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. 2 USB ports
6. one LAN port 10/100 base T Ethernet
7. one external VGA monitor port
8. one IDE connector and HDD power connector for HDD in base
9. one 4 pin lock type DC 12 V power input connector
10.one UPS battery connector
11.one CR port for control over 2 cash drawers max.
12.audio ports (1 Microphone input and 2 optional slim type speakers)
k) Touch control functions: left/right button, double click, drag & draw
l) Dual display support (per OS capability)
m) VGA memory size shared from system memory up to 64 MB
n) Support high performance DDR DRAM in two modules with
maximum memory size 1GB
o) Integrated structure for side mount upgrade kits (KP-100, SD-100, SD-
200 or BC-100U) and optional top mount customer display PD-302
p) The MSR in side mount kit is with software programmable parameters
for Win 2000 or Win XP pro
q) Built-in UPS function to support the system from intermittent power
failure (battery itself is an option)
r) Accidental power off protection – The power switch is safely located
in recessed side, and it can be defined as a “ON” switch only through
software command
s) Preconditioned power up function – by alarm clock or COM port
MODEM ring or LAN
Optional Items:
Note: The underlined items in the following list means that option must be
set prior to shipment from the factory. The rest items can be set by the
dealers.
a) DDR SDRAM memory expansion up to 1GB
b) RS232 interface Infra-Red type touch panel durable for 50 million
touches min. at same spot or select to be without touch function (LT-
5815)
c) Select between slim and universal base
d) Base type select for 2.5” HDD in base
e) Integrated side mount upgrade kit among KP-100, SD-100, SD-200,
BC-100U
f) Integrated rear top mount 2 by 20 LCD customer display PD-302
g) Integrated base mount device choice among: PD-2501 or PD-2602 –
VFD pole display or PD-305 – LCD customer display or LM-6201 –
12.1” or LM-6301 – 15” 2nd LCD monitor
h) USB interface external slim type CD ROM drive or COMBO drive
Part 6
Download from Www.Somanuals.com. All Manuals Search And Download.
i) IDE interface internal slim type CD ROM drive or COMBO in base for
universal base models
j) UPS battery in base
k) Preload OS
l) 2 in 1 cash drawer control cable (CCBLA-238)
m) Wall mount kit: WB-6000, WB-6300, WB-6600, WB-6800
Part 7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION GUIDES
CAUTION: Before any installation or cable connection to the set, please
always make certain that the system is turned off and the
external power source to the set is removed to prevent electric
hazard! Never touch any metal pin in the connectors or
circuits to avoid high voltage hazard or electrostatic discharge
damage unless the operator is well grounded. Failure to do the
above will void the product warranty!
OPENING CABLE COVER
Please follow steps A to C sequentially with reference to pictures
below to remove the cable cover for both slim and universal base models.
B
B
D
A
A
C
Step A: Push lock/release lever back
Step B: Turn panel to most horizontal position
Step C: Use plastic latch key, turn fully counterclockwise
then remove at both sides to release cable cover
Step D: Pull at the removal hollow toward the user
D
DISCONNECTING ALL CABLES
After removal of the cable cover, the connector area will be accessible
then. Please first note orientations of every existing cable connection and
then disconnect every cable properly before separating the main unit from the
adjustable stand assembly. Please note that the click lock spring has to be
pressed down prior to pulling out the connector such as the LAN port or the
CR port. Please also note that the fixing screws have to be loosened free prior
to disconnection such as the VGA port or the COM ports or the LPT port.
Please always hold the connector head instead of pulling on the cable wire
when disconnecting any connector. Failure to do this could damage the cable
and jack that is considered as an artificial destruction. Damages due to
incorrect disconnection operation are not covered by product warranty!
Part 8
Download from Www.Somanuals.com. All Manuals Search And Download.
SEPARATING MAIN UNIT
In order to settle the touch terminal properly in a point of service
system, all the cable connections have to be routed through its base, either slim
or universal. Therefore, please observe the procedures from A to C below to
separate the main unit from both slim and universal base stand assembly after
all cables in cable cover disconnected.
C
B
Step A: Prepare a soft clean flatsurface, such
as a piece ofcloth on the desk to seat
the front surface of main unit
A
Step B: Press the Lock/Release button and
C
B
A
meantime ...
Step C: Slide the base stand assembly to left to
separate
OPENING STAND ASSEMBLY
Take
adjustable
the
stand
Bottom Plate
Fixing Screw
Bottom Plate
Fixing Screw
assembly and turn it up
side down to show the
bottom of the base.
Remove the bottom
plate fixing screw and
push the bottom plate to
the right as in these two
example pictures at both
sides to open.
Push Bottom
Plate This
Way To Open
Push Bottom
Plate This Way
To Open
Auxiliary
Cable Exit
Slim base bottom
Universal base bottom
Take
the bottom plate
up and the
13 11 1
12
1
8
5
7
8
inside of an
example slim
2
4
6
base
model
6
4
looks like this
in
picture.
the
left
The
2
3
5
inside of an
example
11
9
10
6
Inside universal base
universal base
Inside slim base
Part 9
Download from Www.Somanuals.com. All Manuals Search And Download.
model will look like the right picture above. Both with numbered items listed
as below. However, there could be some variation to the contents inside
depending on what option items actually installed. When the HDD installed is
the 2.5” type, the HDD mounting bracket, the metal base chassis and the
bottom plate will also look different.
1. Cable Exit For External Connections
2. Cable Tie
3. CD-ROM Bracket For Universal Base
4. Cable Passage To Main Unit For Desktop Mount Application
5. 3.5” HDD Bracket
6. 3.5” HDD Bracket Fixing Screw
7. Power Adaptor In Universal Base
8. Power Adaptor Bracket Fixing Screws
9. UPS Battery Bracket For Universal Base
10. UPS Battery Bracket Fixing Screw For Universal Base
11. UPS Battery
12. Velcro Strap For UPS Battery In Slim Base
13. 2nd Cable Exit For Slim Base
CABLE PASSAGE
Please route all cables through the cable passage to main unit in
desktop mount application. Hold the cables together with the cable tie. Pass all
cables for external connections (excl. those for HDD and UPS battery) through
the cable exit. For slim base models in desktop mount application, when cable
connection through a hole on desktop underneath the system is required, please
slide open the auxiliary cable exit on bottom plate and route all external
connections through this auxiliary exit. Then fix back the bottom plate if there
is no option unit to install.
INSTALLING UPS BATTERY
The optional UPS battery is delivered in the
carton if it is ordered. For slim base model, please place
the UPS battery in the direction shown in the right picture
and use the Velcro strap through the 2 standing slits on
base box to fix the battery in
position firmly. Route the battery
connection cable through cable
Slim base w/
HDD removed
passage as shown to the battery
connector on the main unit.
Please remove the UPS
battery bracket fixing screw and slide right the UPS
battery bracket to take it out for universal base model
Part 10
Download from Www.Somanuals.com. All Manuals Search And Download.
as in left picture. Put the battery in at the other end first and remount the
bracket with its tongue matching under a bridge in the wall of base box from
the right as arrowed in above left picture then apply the fixing screw. Please
pay particular attention to the environment requirements for UPS battery in
next chapter “USING THE TOUCH POS”.
WALL MOUNTING
WB-6000
WB-6300
WB-6600
WB-6800
Select a flat surface on wall of adequate strength and with proper
ventilation and space condition. Please use the right material to hold this
terminal according to the wall material (Drywall, concrete, solid wood, etc).
Consult with your contractor if it is necessary. A fully equipped system may
weigh up to 11 kg or 23 lbs. Please follow the installation guide delivered with
WB-6000 for its installation.
For WB-6300, WB-6600 and
WB-6800 please separate the back
cover of the wall mount bracket kit and
fix it to wall at the 3 or 4 arrowed holes
as appropriate according to these
pictures on both sides per type of back
covers with proper materials and proper
preparations. Install required optional
device kits with their mechanical
fixation parts in the wall mount bracket
and hang the backpack to the back
cover that is already fixed on wall with
the cables coming out of the brackets
through the openings marked with
rectangles in the above pictures. Screw
lock the top side of the backpack.
Align the four matching pegs on the back of
the main unit as circled in the left picture with the four
matching holes in the wall mount brackets as also
marked in circles in the top pictures and allow the main
unit to slide down the winding grooves in the wall
mount backpack. Connect all cables coming out of the
Part 11
Download from Www.Somanuals.com. All Manuals Search And Download.
backpack into the cable cover area of main unit.
The area required for wall mount application is determined by the
main unit dimensions and is 376 mm in width and 315 mm in height.
BASE MOUNT UPGRADE KIT
On rear edge of the stand assembly for
desktop mount application, there is a rear connect
cover. Either a 2nd LCD display panel option LM-
6201 or LM-6301 or a customer display option PD-
2501 or PD-2602 or PD-305 can be installed here
after removing this cover.
Please note that there could be certain restrictions to the tilt angle
range for the main unit when the base mount upgrade kit is mounted.
Investigation for the acceptability of such kind of restrictions must be taken
before decision to install a base mount upgrade kit.
12” 2nd LCD Panel Or Customer Display
To remove the rear connect cover in slim base please refer to the
inside view of the base unit after removal of UPS
battery as in picture at right and use a flat head
screwdriver to pick the plastic hook plate of the
rear connect cover from inside.
The rear connect cover of universal base can be removed by pushing
the plastic hook plate of it from inside as marked by
white arrow in the right picture. However, this picture
is a top-side-down inside view of the stand assembly
with base box removed for illustration purpose only.
Please push the plastic hook plate with finger through
the top opening in the stand assembly to remove the
rear connect cover.
Fit the joint base of PD-2501
or PD-2602 or PD-305 or LM-6201 to
the rear connect cover opening. Then
make the cable go through the normal
cable exit (under the joint base) as in
these pictures. Fit 2 screws with
washers to hold the joint tight. For low profile customer display PD-305, the
installation procedure is same. Remember to enable the +5 V DC supply in the
COM port of the main unit for PD-2501, PD-2602 or PD-305 or the +12 V DC
in VGA port for LM-6201.
Part 12
Download from Www.Somanuals.com. All Manuals Search And Download.
15” 2nd LCD Panel
Please follow the installation instruction that come alone with the 15”
2nd LCD monitor LM-6301 to mount the interface bracket kit onto the LCD
panel. Fit the interface bracket the same way as joint base of LM-6201 to the
rear connect opening and fix with 2 screws with washers. Route the VGA
through the cable exit of the base stand to the main unit. Connect the attached
power adaptor for its power source.
ROUTING THE CABLES
Place all the cables required for connections to the main unit except
those for the integrated attachment through the front part inside the stand
assembly. Be sure not to damage any cable during this operation.
Route Cables through Front Part
Connect this End to Main Unit
Now, turn the adjustable
stand assembly back to normal
orientation and arrange all cables to
come out of the area for mounting
main unit from the bottom edge for ease of later
operation.
PREPARING THE MAIN UNIT
On the back of the main unit, there is a service window among the 4
matching pegs. Push open the service window to the right to find several
jumpers. The jumpers in this window are designated for VGA port and COM
port power supply function. Please consult your dealer for technical support on
setup of these jumpers. Please note that only those
qualified technicians may adjust in the service window
with information from Posiflex and the contents in the
service window may change without notice as time
develops.
Jumpers
RTC Battery
Service Window
CAUTION
Risk Of Explosion If Battery Is Replaced By An Incorrect Type
Dispose Of Used Batteries According To Local Regulations
SIDE & REAR TOP MOUNT UPGRADE KIT
Please follow the instructions in the manuals delivered with the side
mount upgrade kit: KP100, SD100, SD200 or BC100U and the rear top mount
upgrade kit PD302 to fit them in Jiva system construction.
Part 13
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRELESS PRINTER
To access the Posiflex wireless thermal printer
PP7700 in Windows environment except Win CE, a wireless
Dongle DG2000 for this printer must be separately
purchased and installed to one of the serial COM ports in
Jiva system. Please enable the + 5 V DC power support for
this COM port. Hook the Dongle to either top corner of the
Jiva TP / LT system as in the right picture.
DESKTOP MOUNTING
Matching Holes
Round Part
Slot Part
Matching Pegs
Removal Hollow
Match the matching pegs on the back of the main unit against the
matching holes on the stand assembly. First aim the matching pegs toward the
upper round part of the matching hole on base stand and make sure that all
pegs are inside the holes. Then slide the main unit down to move the pegs into
the lower slot part of the holes till it clicks. Note that all the cables come out of
the stand from the lower edge and shouldn’ t get trapped by this mounting
operation. If later on you want to remove the main unit from the stand, you’ ll
have to press down the lock/release button on back of the stand at the time
lifting the main unit.
For desk top/counter mount application, the adjustable stand assembly
requires a space of 376 mm wide and 321 mm deep and can take maximum
total height of 372 mm for slim base models and 402 mm for universal base
models if no upgrade kit installed.
CONNECTING CABLES
To re-assemble the main unit with stand assembly for operation,
please connect all required cables to the appropriate connectors. Please make
sure that each connector is connected to the correct port with the correct
orientation. Damages due to incorrect connection or orientation are not
covered by product warranty!
Some connectors like the LAN or the cash drawer connector have to
be gently inserted until a click is heard. It is recommended that connectors
Part 14
Download from Www.Somanuals.com. All Manuals Search And Download.
such as the external VGA, LPT and COM connector be screwed into place
once seated. If the COM1 port must be used, the COM1 terminator that
occupies the COM1 port must be removed and safely preserved for future use.
However, when using the COM1 port, it is advisable to use devices that
provide proper hardware handshaking signals in order to keep other embedded
system features. A serial mouse is one example of a device that does not
support handshaking.
Adjust the slack of each cable and close the cable cover. Re-adjust the
tilt angle of the screen for best viewing.
Connect the cables to appropriate external devices through the cable
exit at the bottom of stand assembly. Please make sure that each connector has
to be connected to the right device in the right way.
CAUTION: On doing any insertion or extraction of any connector, please
always hold the connector head itself instead of pulling on the
cable wire. Failure to do this could damage the cable and jack
that is considered as an artificial destruction and is not
covered by the warranty.
OPERATING SYSTEM RECOVERY
For Jiva systems preloaded with Windows XP Pro or WEPOS on HDD,
Posiflex provides recovery CD or DVD delivered with the touch terminal for
the preloaded operating system. The System Integrator shall take care of
software restoration after OS recovered. A Posiflex supplied USB interface
CDROM or COMBO drive or the internal type IDE interface CDROM or
COMBO drive for the universal base models will be required for such action.
Other brand CDROM drive may require its specific driver different from what
supported in the recovery CD or DVD.
Please use the recovery CD or DVD in rescue operation only.
Using it otherwise may wipe out whatever stored in the HDD! All upgrade
devices drivers needed for manual installation in usual way are available in the
subfolder “\drivers” in OS recovered HDD and the latest versions of these
Then follow instructions from your system integrator for software recovery.
OPERATING SYSTEM INSTALLATION
This product is a highly professionalized equipment. The installation
of an OS into a machine without any preloaded OS could constitute major
difficulty for average user or obstacle by possibly unintentional negligence
even for PC veterans to accomplish such a task. Therefore, OS installation into
a system without preloaded OS is highly discouraged. Posiflex shall not be
responsible for any technical support to questions arisen due to non-preloaded
OS.
Part 15
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE TOUCH TERMINAL
APPLICATION ENVIRONMENT
It is very important to check the following operational guidelines:
Ventilation
This terminal must NOT be used in an environment with restricted
ventilation. There must be at least 25 mm air clearance around any ventilation
holes with a free flow of air around the unit at ALL times for the installation.
Operating Environment
The equipment must not be operated or stored in extremes of both
temperature and humidity/moisture. (Operating range 5°C to 40°C and up to
80% humidity – non condensing, max. wet bulb 26°C)
UPS Battery (option)
General care:
The UPS battery is consumables beyond product warranty. Please
definitely observe the alerts in beginning of this manual. Please always
disconnect the battery if the system is to be powered off for more than few
days. Reconnect it and turn on the system to recharge the battery for 1 ~ 2
hours every 3 months / every month for temperature lower than / over 30°C.
Temperature above 40°C must be strictly avoided as it could cause
termination of battery life and unexpected result even if the battery is not in
work. The UPS battery can support basically the data preservation and smooth
operation during intermittent or fewminutes (3 ~ 8 min. depending on loading
and battery condition) power failure.
Battery replacement:
In the preloaded OS for a Jiva system, there is a built in utility Power
Manager that will interface the UPS battery monitor status with user. When a
health warning popup message appears, please immediately replace the used
up UPS battery at power off if the battery is actually connected there but found
inoperable by such messages.
Emergency treatment:
The battery is constructed maintenance free and leakproof. However,
should any accident happen and the sulfuric acid from the battery spills on skin
or clothing, wash immediately with water. If the acid comes in contact with
eyes, rinse eyes with large amount of clean water and see a doctor immediately.
A larger external battery may be connected to give an extended operation.
Please check your dealer about this capability when required.
WARNING:
If there are any signs of over charging or leakage of electrolyte
please contact your dealer immediately
Part 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Supply
The operating voltage range of the power adaptor should cover the
local power supply for proper operation. The power cable, the power outlet
and any power fusing arrangements must conform to local safety regulations.
Please never do any connection / disconnection when system is still
powered on. Please always keep the external power adaptor in a free air
circulation.
POWER ON/OFF
There must always be at least 10 seconds waiting before switching on
again once the system is powered off successfully.
Power Status LED Indicator
There is an LED under the printed logo that serves for several
purposes. The relationship between LED status and other conditions is
summarized in following table:
LED Status System Status External Power UPS Battery Powering Up
Off
Off
Green
Off
Off
Off
On
Off
Off
On
On
Off
Not present Not possible
Present
No influence
Not allowed
Allowed
Blue
No influence Not required
Activated Not required
Running at
Not required
low capacity
Blue/flash
Green/rapid
flash
On
On
Off
Hardware Power Switch
The power switch is at left side of the main unit. This switch turns the
system on when slid downward, only when external power is present. The
switch will always spring back to its original position when pressure is
removed. This button turns the system off when slid downward again during
power on status. However, if the system hangs due to any reason such as
software resource conflict you may have to utilize the forced power off
feature by pressing the switch downward, and holding for within 10 seconds.
In case this forced power off fails, please disconnect the UPS battery if
installed and the AC power supply for few minutes then reconnect them.
This switch can also be programmed as an ON only switch by the
application program so that this switch will always turn the system on when
activated, but will not power off the system when depressed again (the forced
power off feature will not work in this mode). When using this feature, please
Part 17
Download from Www.Somanuals.com. All Manuals Search And Download.
make sure that the software application has the ability to power off the
machine. In preloaded Windows, “Posiflex Power Switch Manager” in
“Posiflex Tools” in the Program Files helps managing these functions.
Software Support Features
The Jiva series provides a software power off for application program
maneuvers as mentioned above. The Jiva also provides a specific means for the
software to detect if the system is working on external or UPS battery power.
So the compatible software applications have the ability to change operating
conditions when running on standard/backup power. The software programmer
may take reference from theJiva technical manual to apply such features.
Automatic Power On Control
The system may also turn on according to some preset conditions
such as Modem Ring Up or Alarm Clock Wake Up or LAN Wake Up.
To utilize Modem Ring Up or Alarm Clock Wake Up function, please
enter the CMOS setup, “Power Management Setup”, “PM Wake Up Events”
and enable the “Ring Power Up Control” or “Power Up by Alarm”. Save the
configuration and exit the CMOS setup program. For LAN wakeup, an
operating caller system connected through LAN to the system is required. It
also requires a qualified networking technician to check the LAN chip ID of
the system for the caller system to wake up.
When the Jiva system is turned off after a successful boot up, the
preset automatic power on functions will turn on the system when the preset
conditions are met. But if the Jiva system is improperly turned off before a
complete boot up procedure, the above preset power on control functions will
be disabled until next turning off after a complete boot up.
DISPLAY ISSUES
Main LCD Display
For best viewing result please set your display resolution at 1024 x
768 with high color.
In configuration of system memory, max. 64 MB can be shared as the
video memory.
VGA Port
The VGA port in the Jiva system supports Posiflex stand alone touch
or LCD monitors like TM-4115, LM-6212 or TM-7112 if there is no base
mount 2nd LCD display. This port supports extended mode dual display
function in WinXP. To support the DC power to these Posiflex monitor, use
the DC adaptor for TM-4115 / TM-7112. Connect the adaptor to VGA cable or
use Posiflex VGA + power cable and set an internal jumper in the main unit to
Part 18
Download from Www.Somanuals.com. All Manuals Search And Download.
supply the required power through the VGA connector for LM-6212. Do not
connect other monitor to this port before the power in this port is disabled.
CUSTOMER DISPLAY
Please follow the instructions on the manual that comes along with
the customer display PD-2501 or PD-2602 when it is installed.
SERIAL PORTS
The serial ports in Jiva system can supply a +5 V DC through pin 9
after proper jumper setting change. However, they are set to standard RS232
serial ports as status at delivery.
COM1 serial port must always be occupied by a suitable serial device
or COM1 terminator (as supplied). If this port is left vacant or connected with
something like a mouse the cash drawer control and the power management
function may fail to work correctly. For serial Modem application, please use
COM2/3/4 port to minimize any hardware resource conflict. For models with
Infra Red type touch, the COM4 port is occupied and covered. Please never
try to open the cover. Otherwise the product warranty is voided.
SOUND PORTS
The audio port in Jiva system supports a Microphone in and a stereo
line out jacks. There is a single channel internal audio amplifier in the output
port to drive the 2 slim type speakers installed in the I/O area inside cable
cover with 1 W audio power (For slim base models this item is an option).
Should the application demand for higher audio power, please first ask your
dealer to disable the internal audio amplifier and connect the amplifier or a pair
of speakers with booster to this port. Please note that this modification should
be handled by a qualified technical person only.
FAN CONTROL
In the preloaded OS for Jiva system, there is an embedded function
that can be enabled and keep monitoring the interior temperature and the fan
revolution rate and regulating each required fan power to obtain maximum
ventilation effect with lowest possible noise. Please find it in “Posiflex Tools”
of “Program Files”. It will remain enabled even after system turning off/on
until being disabled.
On occasion of unexpected system failures, please check the airflow
condition and environment temperature of the system. Check if the fan is stuck
by something like dry grease or threads. Try to correct the situation when the
system is off and cooled down. You may power up the system again after the
system cooled down and trouble cause removed. However, if the failure
repeats, please consult your dealer for possibly fan replacement on worn out.
Part 19
Download from Www.Somanuals.com. All Manuals Search And Download.
TOUCH PANEL
All paragraphs below are applicable for models with touch panel only.
The user of those models without touch panel can ignore them and consider
this user’s manual ends here.
Mouse Emulation
The touch panel in Jiva system uses USB interface as standard. Only
the optional InfraRed type touch panel uses RS232 interface. When the touch
driver is properly installed, this touch panel works exactly like a standard
mouse except when the system is running under safe mode.
The mouse emulation functions include: left button click; click, drag
and drop; left button double click; right button click. The only deviations are:
the system can give a beep (or not to beep) on each touch; a right-click sticky
button is provided for the effect like clicking on the right button of a mouse.
Posiflex USB Touch Manager
A program named “Posiflex USB Touch Manager” and a right-click
sticky button tool in the program group “Posiflex USB Touch Tools” is
installed in the preloaded Windows system with a USB interface touch panel
controller. This program can also be obtained by download from the
POSIFLEX web site.
RS232 Touch Controller
If the Jiva system purchased is the leading edge Infra Red type touch
models, the touch controller is of RS232 interface. The “Posiflex Touch
Terminal Manager” above should be disregarded. In these models, the COM4
port will be covered in the connection area. Removal of this cover will void
the product warranty!!
Once the RS232 touch controller driver is installed, the user can
utilize it to control the mouse emulation. Please click “Start”, “Settings”
“Control Panel” and “Elo Touchscreen” or just click the “elo” icon in tool tray
to engage this utility. However, with this touch controller driver, certain
display mode like full screen display of Windows DOS box should be avoided.
Posiflex Touch Terminal Manager
A program named “Posiflex Touch Terminal Manager” and a right-
click sticky button tool in the program group “Posiflex Tools” is installed in
the preloaded Windows system with a PS/2 interface touch panel controller.
This program can also be obtained by download from the POSIFLEX web site.
T31454
警告使用者
這是甲類的資訊產品，在居住的環
境中使用時，可能會造成射頻干
擾，在這種情況下，使用者會被要
求採取某些適當的對策。
Part 20
Download from Www.Somanuals.com. All Manuals Search And Download.
|