Patton electronic Network Router 07M2160 QS User Manual

CopperLink™ Model 2160 Series

Long Range Ethernet Extender

Quick Start Guide

Sales Ofﬁce: +1 (301) 975-1000

Part Number: 07M2160-QS, Rev. A

Revised: December 14, 2009

Technical Support: +1 (301) 975-1007

E-mail: [email protected]

WWW: www.patton.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Printer

WAP

Notebook

RAID Drive

Server

Desktop PC

Switch

Desktop PC

Notebook

LAN

DC 9V

MGMT

CONSOLE

LINE

RST

LAN

Desktop PC

Laptop computer

Figure 1. Model 2160 Connection Diagram

2.0 Choose a conﬁguration method and log in

There are three methods to conﬁgure the Model 2160: serial console, Telnet and Web Browser. You must choose

one method to conﬁgure the Model 2160.

2.1 Web conﬁguration

Make sure that an Ethernet Adapter has been installed in the PC or NB you will use to conﬁgure the modem.

TCP/IP protocol is necessary for web conﬁguration, so check if the TCP/IP protocol has been installed.

The Model 2160 provides a browser interface that allows you to conﬁgure and manage the Model 2160. After

you set up the IP address for the Model 2160, you can access the Web interface applications directly in your

browser by entering the IP address of the Model 2160. You can then use your Web browser to list and manage

conﬁguration parameters from a PC.

Web Conﬁguration requires Internet Explorer 5.0 or later or Netscape Navigator 6.0 and later versions. The rec-

ommended screen resolution is 1024 by 768 pixels.

Model 2160 Series Quick Start Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

2.2 Serial console conﬁguration

For conﬁguring the Model 2160 through the serial console, connect a terminal or a PC equipped with a terminal-

emulation program (such as Hyper Terminal) to the Model 2160's console port.

Use the supplied serial cable (RJ-45 to DB9F) to connect the Model 2160 to a PC. After marking the connection,

conﬁgure the terminal-emulation program using the following parameters: 9600 bps , 8 data bits , no parity

and 1 stop bit.

2.3 Telnet conﬁguration

Make sure that an Ethernet Adapter has been installed in the PC or NB you will use to conﬁgure the Ethernet

extender. The Model 2160 also supports Telnet for remote conﬁguration. The command is “telnet 192.168.1.1”

. For logging into the system through a Telnet connection, “admin” for username and “admin” for password.

The default IP address is 192.168.1.1. You may change the IP address for your application.

3.0 Additional information

For detailed information about installing, conﬁguring, operating, and troubleshooting your Model 2160, refer to

the Model 2160 Getting Started Guide on the enclosed Patton CD-ROM or at www.patton.com/manuals.

A.0 Compliance Information

A.1 Compliance

EMC:

• FCC Part 15, Class A

• EN55022, Class A

• EN55024

A.2 Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in

strict accordance with the manufacturer's instructions—may cause interference to radio and television recep-

tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accor-

dance with the speciﬁcations in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable

protection from such interference in a commercial installation. However, there is no guarantee that interference

will not occur in a particular installation. If the equipment causes interference to radio or television reception,

which can be determined by disconnecting the cables, try to correct the interference by one or more of the fol-

lowing measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna,

and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and

receiver are on different branches).

Model 2160 Series Quick Start Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

A.3 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Speciﬁcations. This is con-

ﬁrmed by the registration number. The abbreviation, IC, before the registration number signiﬁes that registra-

tion was performed based on a Declaration of Conformity indicating that Industry Canada technical speciﬁcations

were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective,

operational and safety requirements. The Department does not guarantee the equipment will operate to the

user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also be installed using an acceptable

method of connection. In some cases, the company’s inside wiring associated with a single line individual service

may be extended by means of a certiﬁed connector assembly (telephone extension cord). The customer should

be aware that compliance with the above condition may not prevent degradation of service in some situations.

Repairs to some certiﬁed equipment should be made by an authorized maintenance facility designated by the

supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for

their own protection that the ground connections of the power utility, telephone lines and internal metallic water

pipe system, are connected together. This protection may be particularly important in rural areas.

A.4 CE Declaration of Conformity

We certify that the apparatus described above conforms to the requirements of Council Directive 2004/108/EC

on the approximation of the laws of the member states relating to electromagnetic compatibility; and Council

Directive 2006/95/EC on the approximation of the laws of the member states relating to electrical equipment

designed for use within certain voltage limits.

The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above

directive is indicated by the CE sign on the device.

A.5 Authorized European Representative

D R M Green

European Compliance Services Limited.

Oakdene House, Oak Road

Watchﬁeld,

Swindon, Wilts SN6 8TD, UK

Model 2160 Series Quick Start Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

Trademarks statement

The term CopperLink is a trademark of Patton Electronics Company. All other trademarks presented in this docu-

ment are the property of their respective owners.

Patton support headquarters in the USA

• Online support: Available at www.patton.com

• E-mail support: E-mail sent to [email protected] will be answered within 1 business day

• Telephone support: Standard telephone support is available ﬁve days a week—from 8:00 am to

5:00 pm EST (1300 to 2200 UTC/GMT)—by calling +1 (301) 975-1007

• Support via VoIP: Contact Patton free of charge by using a VoIP ISP phone to call sip:[email protected]

• Fax: +1 (253) 663-5693

Alternate Patton support for Europe, Middle East, and Africa (EMEA)

• Telephone support: Standard telephone support is available ﬁve days a week—from 8:00 am to

5:00 pm CET (0900 to 1800 UTC/GMT)—by calling +41 (0)31 985 25 55

• Fax: +41 (0)31 985 25 26

Note For additional service and support information, refer to the “Contacting Patton for assistance” chapter

of the CopperLink 2160 Getting Started Guide located on the CD-ROM that came with your CopperLink

2160 Modem or available online at www.patton.com.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the CopperLink Model 2160 Getting Started Guide

located on the CD-ROM that came with your NTU or available online at www.patton.com.

In accordance with the requirements of council directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate

this product from other waste and scrap and deliver to the WEEE collection system in

your country for recycling.

Model 2160 Series Quick Start Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

____________________________________________________________________

Model 2160 Series Quick Start Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

____________________________________________________________________

Model 2160 Series Quick Start Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

MTD Air Cleaner PPN 41ADY70G000 User Manual
NAD DVD Player T 571 User Manual
Napoleon Fireplaces Indoor Fireplace EF30 User Manual
NETGEAR Network Router WNR200v4 User Manual
New Holland Lawn Mower 157 User Manual
Nostalgia Electrics Blender MSH 105 User Manual
Olympus Microcassette Recorder WS 811 User Manual
Onkyo Speaker System CR 305TX User Manual
Panasonic Cell Phone EB VS2 User Manual
Parasound Stereo Amplifier Zpre2 User Manual