Patton electronic Network Card 1053 User Manual

USER

MANUAL

MODEL 1053

iDSL Modem with

RS-232 Interface

Part# 07M1053-UG

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

Doc# 05815U2-001 Rev. A

Revised 11/10/04

An ISO-9001

Certiﬁed

Company

Download from Www.Somanuals.com. All Manuals Search And Download.

Model 1053/A Factory Replacement

Parts and Accessories ............................................................. 17

Model 1053/A Interface Pin Assignments............................... 18

Download from Www.Somanuals.com. All Manuals Search And Download.

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 1053 components to be free from

defects, and will—at our option—repair or replace the product should it

fail within one year from the ﬁrst date of shipment.

This warranty is limited to defects in workmanship or materials, and does

not cover customer damage, abuse or unauthorized modiﬁcation. If this

product fails or does not perform as warranted, your sole recourse shall

be repair or replacement as described above. Under no condition shall

Patton Electronics be liable for any damages incurred by the use of this

product.These damages include, but are not limited to, the following: lost

proﬁts, lost savings and incidental or consequential damages arising

from the use of or inability to use this product. Patton Electronics spe-

ciﬁcally disclaims all other warranties, expressed or implied, and the

installation or use of this product shall be deemed an acceptance of

these terms by the user.

1.1 FCC INFORMATION

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules.These limits

are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a commercial environment.This

equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own

expense. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates that it is in

compliance with the Electromagnetic Compatibility (EMC) directive and

the Low Voltage Directive (LVD) of the Union European (EU). A Certiﬁcate

of Compliance is available by contacting Patton Technical Support.

Download from Www.Somanuals.com. All Manuals Search And Download.

Conformity documents of all Patton products can be

viewed online at www.patton.com under the appropriate

product page.

Important

1.3 SERVICE

All warranty and non-warranty repairs must be returned freight prepaid

and insured to Patton Electronics. All returns must have a Return Materi-

als Authorization number on the outside of the shipping container. This

number may be obtained from Patton Electronics Technical Service at:

Tel: (301) 975-1007

E-mail: [email protected]

URL: www.patton.com

Note Packages received without an RMA number will not be

accepted.

Patton Electronics’ technical staff is also available to answer any ques-

tions that might arise concerning the installation or use of your

Model 1053. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product. This

product has been thoroughly inspected and tested and is warranted for

One Year parts and labor. If any questions or problems arise during

installation or use of this product, please do not hesitate to contact

Patton Electronics Technical Support at (301) 975-1007.

2.1 FEATURES

• Synchronous data rates: 32, 56, 64, and 128 kbps

• Asynchronous data rates: 0–38.4, 57.6, 76.8, and 115.2 kbps

• Full duplex operation over a single twisted pair (2-wires)

• Point-to-point distances up to 5 miles (all data rates) on 24 AWG

twisted pair

• Multi-rate symmetric DSL

• RS-232 Interface

• Compatible with popular Models 1092A, 1082, and 1052

• Universal power options, 120 VAC and -48, -24, and -12 VDC available

• LED status indicators

• Small, convenient desktop unit

• CE marked

2.2 DESCRIPTION

The Patton Model 1053 is a high speed, AC powered short range modem

that is able to operate synchronously or asynchronously—full duplex—

over a single twisted pair. Supporting data rates up to 128 kbps (syn-

chronous) or 115.2 kbps (asynchronous), the Model 1053 is capable of

point-to-point distances up to 5 miles (8 km) using 24 AWG wire. The

Model 1053 supports internal, external, or receive recovery clocking, and

asynchronous data rates may be conﬁgured locally using DIP switches.

The Model 1053/A provides an RS-232 interface on a DB-25 female con-

nector. Line connection is made by an RJ-45 jack. Standard versions of

Model 1053 are powered by a 100–240 VAC (Universal) supply. The DC

power supply options support either -12, -24, or -48 VDC.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.0 CONFIGURATION

The Model 1053 is equipped with 16 DIP switches that enable conﬁgura-

tion of the unit for a wide variety of applications. This section describes

switch locations and explains the different conﬁgurations

3.1 CONFIGURING THE HARDWARE DIP SWITCHES

S1 and S2 each contain eight internal DIP switches (see Figure 1) that

are used for conﬁguration reset purposes only. To access switch sets,

use a small ﬂat blade screwdriver to open the Model 1053’s case as

shown in Figure 2 on page 8.

Figure 1. DIP switches S1 and S2

To conﬁgure the DIP switches, use a small screwdriver and gently push

each switch to its proper setting. The ON and OFF positions are shown

in Figure 1.

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 2. Opening the Model 1053 case

Figure 1 on page 7 shows the orientation of the DIP switches in the “ON”

and “OFF” positions.

Conﬁguring DIP Switch S1

DIP switch S1 is where you conﬁgure the data rate, asynchronous or

synchronous data format, transmit clock source. The following table sum-

marizes default positions of DIP switches S1-1 through S1-8. Detailed

descriptions of each switch follow the table.

Switches S1-1 and S1-2: Data Rate. Use switches S1-1 and S1-2 to

conﬁgure the asynchronous or synchronous data rate of the Model 1053.

Download from Www.Somanuals.com. All Manuals Search And Download.

Each setting represents one synchronous data rate and one asynchro-

nous data rate.

S1-1 S1-2

Sync Data Rate

Async. Data Rate

Off

128 kbps

64 kbps

56 kbps

32 kbps

115.2 kbps

57.6 kbps

76.8 kbps

0–38.4 kbps

Note If the S2-1 switch is positioned in the OFF position, the 128 kbps

sync data rate/0–38.4 kbps async data rate option is selected.

Switch S1-3: Must be set to the ON position (Reserved).

S1-3

Setting

Reserved

Switch S1-4: Must be set to the ON position (Reserved).

S1-4

Setting

Reserved

Switch S1-5: Asynchronous/Sync Operation. Use Switch S1-5 to

conﬁgure the Model 1053 for async/sync operation. For synchronous

data rates set switch S1-5 OFF. For asynchronous rates set switch

S1-5 ON.

S1-5

Setting

Off

Sync

Async

Switches S1-6 and S1-7: System Clock Mode. Use Switches S1-6

and S1-7 to conﬁgure the 1053 for internal, or receive recover clock

mode.

S1-6 S1-7

Clock Mode

Description

Off

Internal

System clock generated internally

External (DTE)

System clock derived from termi-

nal interface

Off

Receive Recover

Hardware Reset

System clock derived from the

received line signal

Download from Www.Somanuals.com. All Manuals Search And Download.

A pair of Model 1053s communicate synchronously

across the twisted pair line connection. Therefore, you

must set these switches whether your application is

async or sync. For Sync or Async applications, please

conﬁgure one Model 1053 for internal clock mode and the

other Model 1053 for receive recover clock mode.

Important

Switch S1-8: Must be set to the OFF position (Reserved).

S1-8

Setting

Off

Reserved

Conﬁguring DIP switch S2

DIP switches in S2 are reserved and must be set in the OFF position.

The following table summarizes default positions of DIP switches S2-1

through S2-8.

Download from Www.Somanuals.com. All Manuals Search And Download.

4.0 INSTALLATION

Once the Model 1053 has been conﬁgured, it is ready to connect to the

twisted pair interface, the serial port, and the power source. This section

tells you how to make these connections.

Figure 3. Model 1053 Rear Panel

4.1 CONNECTING THE TWISTED PAIR INTERFACE

The Model 1053 supports communication between two DTE devices at

distances to 5 miles (8 km) over 24 AWG (0.5 mm) twisted pair wire.Two

things are essential:

• These units work in pairs. Both units at the end of the twisted pair DSL

span must be set for the same DTE rate.

• To function properly, the Model 1053 needs one twisted pair of metallic

wire. This twisted pair must be unconditioned, dry, metallic wire,

between 19 (0.9 mm) and 26 AWG (0.4 mm) (the higher number

gauges will limit distance). Standard dial-up telephone circuits, or

leased circuits that run through signal equalization equipment, or stan-

dard, ﬂat modular telephone type cable, are not acceptable.The RJ-45

connector on the Model 1053’s twisted pair interface is polarity insensi-

Download from Www.Somanuals.com. All Manuals Search And Download.

tive and is wired for a two-wire interface. The signal/pin relationships

are shown in Figure 4.

Figure 4. Model 1053 twisted pair line interface

4.2 CONNECTING THE MODEL 1053/A (RS-232)

The Model 1053/A supports RS-232 serial port connections.This section

describes how to connect the serial ports to your RS-232 equipment.

Connecting the Model 1053/A (RS-232) to a DTE Device

The Model 1053/A provides an RS-232 DCE (data circuit terminating

equipment) interface on a DB-25 female connector. As a DCE, this inter-

face is designed to connect to DTE equipment, such as a router. When

connecting the RS-232 interface of the Model 1053/A to your DTE

device, use an RS-232 straight-through cable (see Figure 5). Appendix C

on page 18 describes pin assignments and signal sources for the Model

1053/A RS-232 interface. When purchasing or constructing an interface

cable, use the pin diagrams in Appendix C as a guide.

Figure 5. Connecting the Model 1053/A to an RS-232 serial DTE

4.3 POWER CONNECTION

The Model 1053 (all versions) are available with Universal AC (100–240

VAC), 120 VAC, 230 VAC or -12, -24, or -48 VDC power options. This

section describes these options.

Download from Www.Somanuals.com. All Manuals Search And Download.

Universal AC Power (100–240 VAC)

The Model 1053 uses a 5VDC, 2A universal input 100–240VAC, power

supply (center pin is +5V). The universal input power supply has a male

IEC-320 power entry connector. This power supply connects to the

Model 1053 by means of a barrel jack on the rear panel. Many interna-

tional power cords are available for the universal power supply (Refer to

Appendix B on page 17 for country-speciﬁc power cords. The Model

1053 powers up as soon as it is plugged into an AC outlet—there is no

power switch.The Universal AC supply is equipped with a male IEC-320.

DC Power

The optional -12, -24, or -48 VDC DC-to-DC adapter supplied with the

DC version of the Model 1053 plugs in a DC source (nominal -12, -24, or

-48 VDC) and plugs into the barrel power supply jack on the rear of the

1053. Refer to Figure 6 to make the proper connection.

Figure 6. Connecting DC power to the 48V-PSM DC power supply

There are no user-serviceable parts in the power

supply section of the Model 1053. Fuse replacement

should only be performed by qualiﬁed service per-

sonnel. Contact Patton Electronics Technical sup-

port at +1 (301) 975-1007, via our web site at

www.patton.com, or by E-mail at [email protected],

for more information.

WARNING

Download from Www.Somanuals.com. All Manuals Search And Download.

5.0 OPERATION

Once the Model 1053 is properly conﬁgured and installed, it should oper-

ate transparently. This sections describes power-up, reading the LED

status monitors.

5.1 POWER-UP

Before applying power to the Model 1053, read section 4.3, “Power Con-

nection” on page 12 to ensure that the unit is connected to the appropri-

ate power source.

5.2 LED STATUS MONITORS

The Model 1053 features six side-panel LEDs (see Figure 7). Table 1

describes the function of each LED.

Figure 7. Model 1053 side panel LEDs

Table 1: LED descriptions

LED

Description

TXD

RXD

LINK

(Active: Green) When lit, indicates data transmission.

(Active: Green) When lit, indicates that the end-to-end DSL

framer link is up, signifying that the link across the DSL span

is active. The DSL Link LED is off when the link is down.

(Active:Yellow) When the No Signal LED is lit, it indicates

that the local Model 1053 is not connected with the remote

Model 1053

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX A

MODEL 1053 SPECIFICATIONS

A.1 TRANSMISSION FORMAT

Synchronous or asynchronous

A.2 TRANSMISSION LINE

Single unconditioned twisted pair

A.3 CONTROL SIGNALS

CD and RTS

A.4 CLOCKING

Internal, external, or receive recover

A.5 DISTANCE

Distance, max, all data rates:

• 10.1 miles (16.4km) on 19 AWG (0.9 mm) wire

• 7.2 miles (11.5 km) on 22 AWG (0.64 mm) wire

• 5.0 (8 km) on 24 AWG (0.5 mm) wire

• 3.4 (5.5 km) on 26 AWG (0.4 mm) wire

A.6 DATA RATES

• Synchronous: 32, 56, 64, and 128 kbps

• Asynchronous: 0–38.4, 57.6, 76.8, and 115.2 kbps

A.7 LED STATUS INDICATORS

TXD, RXD, Link, NS (no signal), ER (CRC error)

A.8 CONNECTORS

RJ-45 on DSL line side; DB-25 female on serial interface side

A.9 POWER

100–253 VAC, 50–60 Hz (universal input option); 48 VDC (optional),

5 watts

Download from Www.Somanuals.com. All Manuals Search And Download.

A.10 TEMPERATURE RANGE

32–122°F (0–50°C)

A.11 ALTITUDE

0–15,000 feet (0–4,572 meters)

A.12 HUMIDITY

5–95% non-condensing

A.13 WEIGHT

2.01 lbs. (1.0 kg)

A.14 LINE INTERFACE

Transformer coupled 1500 VAC isolation

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX B

MODEL 1053/A FACTORY REPLACEMENT

PARTS AND ACCESSORIES

Model #

Description

1053/A

RS232 iDSL Modem

12V-PSM

24V-PSM

48V-PSM

12 VDC Power Supply Module

24 VDC Power Supply Module

48 VDC Power Supply Module

08055DCUI 100–240VAC (+5V ±5% reg. DC/2A) Universal Input Adapter

0805EUR

0805UK

0805US

0805AUS

0805DEN

0805FR

0805IN

European Power Cord CEE 7 (“A”)

United Kingdom Power Cord (“D”)

American Power Cord (“K”)

Australia/New Zealand Power Cord (“C”)

Denmark Power Cord (“E”)

France/Belgium Power Cord (“F”)

India Power Cord (“G”)

0805IS

Israel Power Cord (“H”)

0805JAP

0805SW

07M1053

Japan Power Cord (“J”)

Switzerland Power Cord (“L”)

User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX C

MODEL 1053/A INTERFACE PIN ASSIGNMENTS

RS-232 INTERFACE

(DB-25 Female Connector)

(DCE Orientation)

Pin #

Signal

Shield GND

TD (Transmit Data) (DTE Source)

RD (Receive Data) (DCE Source)

RTS (Request to Send) (DTE Source)

CTS (Clear to Send) (DCE Source)

DSR (Data Set Ready) (DCE Source)

SGND (Signal Ground)

CD (Carrier Detect) (DCE Source)

TC (Transmitter Clock) (DCE Source)

RC (Receiver Clock) (DCE Source)

DTR (Data Terminal Ready) (DTE Source)

XTC (External Transmit Clock) (DTE Source)

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

_________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

_________________________________________________________

Patton Electronics Company

Download from Www.Somanuals.com. All Manuals Search And Download.

Miele Cooktop KM 5987 User Manual
NAD DVD Player T515 User Manual
Nagra MP3 Player Audio Recorder User Manual
New Holland Lawn Mower 300GM Series User Manual
Onkyo Stereo Receiver TX SR804 User Manual
Optoma Technology Projector HD8200 User Manual
Panasonic Camera Accessories AJ0RC10G User Manual
Panasonic Home Theater System SC PTX5 User Manual
Panasonic Network Card AX40 User Manual
Parkside Heat Gun PHLG 2000 2 User Manual