P 5
2.1 Channel Stereo Preamplifier
OWNER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
4
5
Placement and Ventilation Guidelines
AC Mains Voltage
Rack Mounting
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
5
.
.
5
Analog Audio Input Connections
6
Home Theater Bypass Input
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
8
Digital Audio Inputs
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
9
USB Computer Setup
10
10
11
11
13
14
15
17
19
20
Audio Output Connections
Subwoofer Setup
.
.
.
.
.
.
.
Main and Subwoofer Crossover Setup
Turn On Options
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Other Rear Panel Connections
Front Panel Operation.
Remote Control Functions
Problem and Remedies
.
.
.
.
.
.
.
.
.
.
.
.
.
.
If You Require Assistance or Warranty Repair
Specifications
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
21
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Thank You for Choosing Parasound
Your new Parasound Halo P 5 is an advanced 2.1 channel stereo preamplifier that has been
designed for the most advanced performance for serious two channel music listening and ease of
integration with a surround sound system. The P 5 is built to the extremely strict quality and
performance standards for which Parasound is renowned. We’re proud to offer you this
exceptional audio component that will bring you many years of enjoyment and dependability.
Because your new Halo Series P 5 Preamplifier performs at a higher level of sonic performance
than you may have expected we encourage you to read this entire manual to maximize your
enjoyment. We wish you many years of listening enjoyment.
-The Parasound Staff
Keeping Records for Future Reference
Record the serial number located on the back panel or bottom of your P 5 in the space below. Also
note your Parasound Dealer’s name and telephone number. Your purchase receipt/bill of sale is
required to determine if your P 5 is eligible for Parasound warranty service. We recommend that
you make an extra copy of your original purchase receipt/bill of sale and store it inside the P 5’s
carton.
Parasound P 5 Amplifier Serial #: ______________ (5 digit number below the bar code)
Parasound Dealer: ___________________________________________________
Parasound Dealer Phone Number: ___________________
Date of Purchase: ______________________
Important Warranty information
There is no Parasound warranty for this unit if it was not purchased from an Authorized
Parasound Dealer. Investigate warranty coverage statements made by an unauthorized dealer
very carefully, as you will need to depend entirely upon your dealer, and NOT upon Parasound.
Unauthorized dealers lack the capability to make repairs or arrange for repairs of Parasound
equipment. A list of Authorized Parasound Dealers and detailed warranty information is available
A missing or altered serial number could indicate that this unit was re-sold by an unauthorized
dealer or is stolen merchandise. If this unit is missing its serial number or the serial number has
been altered, you should return it to your dealer immediately for a full refund.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking Your P 5 & Placement Guidelines
Unpacking Your P 5
Carefully remove your P 5 from its shipping carton and locate the enclosed accessories:
• AC power cord
• Two trigger wires, one with mono 3.5 mm mini plugs, one with a mono 2.5mm sub-mini plug
and a mono 3.5mm mini plug
• Remote Control with AAA batteries
• USB A to USB B cable for music playback from a computer
• Stereo cable with stereo 3.5mm mini plugs for using the front panel AUX input
While you are unpacking your P 5, inspect it thoroughly for possible shipping damage and tell
your Parasound dealer immediately if you find any evidence of shipping damage. This would be a
good time to make a copy of your sales receipt to store with the P 5’s original packing.
Note: Please save and store both the inner and outer cartons and, most especially, the foam
packing inserts to protect the P 5 if you have to move it or ship it. You may wish to flatten the
cardboard cartons to save room in storage after cutting the taped seams on the bottom flaps.
Placement Guidelines
The P 5 will be easier to use and will last longer if you follow these simple guidelines:
• Use input and output cables that are long enough to leave some slack; that will enable you to
pull the P 5 out of a cabinet to check or to change connections without inadvertently
disconnecting cables.
• Place your P 5 where you can route input and output signal cables as far as possible from any
AC cords.
• Where signal cables must cross AC cords they should do so only at a 90° right angle.
Ventilation Requirements
• Always position the P 5 horizontally.
• The P 5 should never be stacked above a power amplifier.
• The P 5 should not be placed in a completely enclosed cabinet.
AC Mains Voltage
The P 5 will operate on AC mains voltage of 100V-240V. There is no need for any fuse or wiring
changes to switch between 115V and 230V operation.
Rack Mounting your P 5
With its four feet removed, the P 5’s front panel height occupies two rack spaces: 3.5” or 88.2 mm.
(A single standard rack space occupies 1.75” vertical space.) For mounting in a standard 19”
equipment rack, you must use the Parasound HRA 2 rack mount kit (purchased separately). The
HRA 2 kit includes four bolts and eight plastic washers with raised “shoulders.” Slide one washer
onto each mounting bolt with its raised shoulder pointing toward the panel hole. Insert the bolt
through the hole and slide the other washer on the bolt with its raised shoulder facing the rear side
of the panel. The washers will sandwich the P 5 panel and the four mounting bolts to prevent
metal-to-metal contact between the P 5 chassis, the equipment rack, and the other components
mounted in the rack.
Warning: Do not put the screws for the feet back into the bottom of the P 5 without the feet. Doing
so could cause the screws to touch electrical components and cause a short circuit.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Analog Audio Input Connections
Always disconnect your P 5's AC cord before making or changing any input, output or trigger wire
connections. Inserting or removing an input or output cable while the P 5 is turned on can result in
a blast of sound that could damage your loudspeakers. Make sure there is no strain or tension on
any cables that could cause them to pull loose.
Phono Input
The P 5 is equipped with a high quality phono preamplifier. If you wish to connect a turntable,
set the Load/Cartridge switch to MM (moving magnet) or MC (100Ω or 47kΩ moving coil),
depending on your cartridge type. Select MM if you are not sure which type of phono cartridge
you have because MM cartridges are more common. If you use the MC setting with an MM
cartridge the volume level will be very high and distorted. Only a turntable can be connected
to the Phono input.
Phono Load/Cartridge Switch
The Phono input has a 3 position load/cartridge selector switch. Select the switch position that
matches your turntable cartridge type. We recommend that you contact the cartridge
manufacturer if you are unsure which setting is best for your equipment. You may also try all
three settings and use the setting which sounds the best in your system and listening room.
.
MM is for moving magnet cartridges. It provides a 47k ohm load and the appropriate gain
for all MM cartridges. This is the most common cartridge type.
MC 100Ω is for most moving coil cartridges. It provides the higher gain required for even
very low output MC cartridges and a 100 ohm load that is ideal for the majority of MC
cartridges.
MC 47kΩ provides the appropriate gain for MC cartridges with an alternative 47k ohm
load. You can try both the 100Ω and 47kΩ settings to see which sounds best in your
system. The MC 47k Ω setting is also the load Grado recommends for their MI (moving
iron) cartridges.
Note: If your turntable won’t reach adequate volume, or if it plays too loud, you have
selected the incorrect cartridge type. Don’t forget to connect the ground wire from your
turntable to the Phono GND (ground) terminal on the P 5.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Analog Audio Input Connections (Continued)…
RCA line level Input Jacks (inputs 1-5)
Source inputs 1–5 all have the same input sensitivity and input impedance and they are
compatible with any typical analog line level source.
Note: Input 5 is shared with the XLR balanced input, therefore the RCA and
XLR jacks for input 5 should not be connected at the same time.
XLR Balanced Input (input 5)
Input 5 uses balanced XLR type jacks. Use this input to connect an analog source which has
balanced outputs. A balanced line provides superior hum and noise cancellation, especially
for long cable runs.
Note: Input 5 is shared with the XLR balanced input, therefore the RCA and
XLR jacks for input 5 should not be connected at the same time.
Front Panel Aux Input
For your convenience there is an input jack on the front panel for a portable MP3 player (or
smart phone). Connect the included cable with 3.5mm stereo plugs between the portable
player or smart phone’s headphone jack and the P 5’s Aux input jack. The Aux input has an
additional gain stage that boosts the input signal by 12dB so that the volume level remains
consistent when you select your other source components. For the best result set your
portable player’s volume to at least 75% of its maximum level.
Note: If you connect a component other than a portable MP3 player to the Aux Input jack,
the volume level will probably be too high and possibly distorted.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Home Theater Bypass Input
The Bypass input jacks are used to incorporate the P 5 into a surround sound system. This
enables you to use the power amplifier (or two channels of a multi-channel amp) driving your Left
and Right front speakers and subwoofer(s) with stereo sources connected to the P 5 and with
your surround sound system. The Bypass input works by passing the incoming L, R and Sub
channels directly through to the L, R and Sub output jacks. None of the P 5 circuits or controls
has any effect on the bypassed signals. The P 5 is thus transparent to the Left, Right and
Subwoofer(s) outputs from your surround sound processor or receiver and passes them on to
your amplifier(s) and Subwoofer(s).
Note: In order to use the P 5 Bypass function your surround sound
receiver must have line level preamp output jacks.
The P 5’s Bypass function is a direct connection between its L, R and Sub Bypass Input jacks
and its Main and Sub output jacks. All controls are excluded from the bypass signal path.
Adjusting the P 5 Volume will not change the volume level of the Bypass input
The Bass and Treble Tone controls do not function; frequency response is flat,
regardless of how these controls are adjusted.
The Left/Right Balance control does not function; channel balance is equal,
regardless of how this control is adjusted.
The Main Outputs are full range, regardless of the crossover settings
The Sub Outputs are full range, regardless of the crossover settings
The exclusions above are intentional so your surround sound receiver (or processor)’s bass
management menu settings and volume control) function normally when you are listening to
surround sound with the Left, Right and Sub channels routed through the P 5. Please see the
owner’s manual for your surround sound receiver or processor to set the proper speaker levels,
distance and bass management. If you have already calibrated your surround sound system,
there is no need to recalibrate your system after adding the P 5. Don’t forget that the volume
control on the P 5 does not work when the Bypass Input is selected. Use the volume control
on your surround sound AVR or processor.
Connecting the Bypass Input
Connect your surround sound receiver’s Left, Right & Sub(s) preamp output jacks to the P 5’s
Left, Right & Sub(s) Bypass Input jacks. With a single subwoofer you can use either the Sub 1
or Sub 2 Input jacks.
Note: Two Bypass Subwoofer Input jacks are included in case you have two
subwoofers and your surround receiver includes two Subwoofer out jacks.
Selecting the Bypass Input
The Bypass Input can be selected by two different methods:
P 2 is Already Turned On:
When the P 5 is turned on you can select the Bypass input with the remote control
or the front panel Input selector knob.
P 2 is Turned Off:
The Bypass input is automatically selected whenever the P 5 is turned off. This
makes it easy to use your surround sound equipment even without turning the P 5 on.
Note: Do not connect a source component such as a cd player, blu-ray player, tape deck
or tuner directly to the bypass input. Since there is no volume control with this input
the full voltage output of the source will go directly to the power amplifier. The sound
level could be extremely high and could damage your speakers and hearing.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Inputs (OPT, COAX, USB)
The P 5’s built in DAC (Digital to Analog Converter) uses a high resolution 192kHz Burr-Brown
DAC IC. Since the P 5’s DAC is superior to the DAC in most source components. They will
sound better if you connect their digital output to the P 5 instead of using its conventional analog
line output.
Opt (Optical)
The optical input is a high speed Toslink receiver with a 25MHz bandwidth. It accepts these
standard sampling rates: 8kHz, 11.025kHz, 16kHz, 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96
kHz, 176.4kHz and 192kHz. It accepts 16 bit and 24 bit word lengths.
Optical Cable Note: 176.4 kHz and 192 kHz sampling rates will only play reliably with
a very short optical cable. Be careful when handling the optical cable. It has limited
flexibility and it cannot be bent at a sharp angle without impairing its ability to transfer
the digital signal from your source to the P 5.
Coax (Coaxial)
The Coax (also called S/PDIF) input connector is an RCA jack. The Coaxial input accepts
these standard sampling rates: 8kHz, 11.025kHz, 16kHz, 32kHz, 44.1kHz, 48kHz, 88.2kHz,
96kHz, 176kHz & 192kHz. It accepts 16 bit and 24 bit word lengths.
USB
The USB input is used to connect your P 5 to your PC or Mac computer. This allows high
quality playback of any music that is stored on your computer and streaming music services
accessed over the internet. The USB accepts sampling rates of 44.1kHz, 48kHz, 88.2kHz
and 96kHz. It accepts 16 bit and 24 bit word lengths. The P 5 uses the USB 1.1 Audio
standard which allows use of 15’ (5 m) USB cables without any performance penalty.
USB Cable Note: Use a high quality USB cable for the best results. This is particularly
important for cables that are more than 6' (2 m) long. Inexpensive,
long USB cables are often unreliable and could cause drop outs.
Using a Blu-ray or DVD Player's Digital Output
If you use a Blu-ray, DVD player, Cable Box or Satellite Receiver’s digital output with the P 5 you
must go to its setup menu and set the player’s digital audio output to Stereo PCM (2.0). The P 5
accepts only two-channel stereo PCM. It does not accept Dolby, DTS or DSD format signals.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
USB - Computer Setup
First, turn on your computer, then connect the USB cable (included in the P 5 carton) and then turn
on the P 5. The first time you connect your P 5 to a computer it will automatically install the correct
drivers. Next you will need to ensure that the P 5 is set as the computer’s default audio output
device. Follow these instructions to assign the P 5 as the default audio device:
®
For a Windows PC
- Right click on the loudspeaker icon
- Select “Playback Devices”
in the bottom right of your screen (on the tool bar)
- When the “Sound” window pops up click on the “PARASOUND P 5” and then click “Set as Default”
- Click “OK” to close the “Sound” window
Note: If for some reason you cannot find the loudspeaker icon you will need to go to the sound
options in the Control Panel and select the P 5 as the default playback device.
®
For a Mac with OS X
- Go to the Apple Menu
- Select “System Preferences”
- Select “Sound” from the Hardware Menu
- Select “PARASOUND P 5” in the Sounds Menu
Playing Music From Your Computer
Once initial setup is complete your P 5 will be ready for use with your PC or Mac. Press the USB
button on the P 5’s remote control or rotate the P 5’s Input select knob until the blue indicator for
USB is illuminated. Simply start playing any music on your computer and it will be sent to the P 5
via the USB cable. Any sound that you would normally hear through your computer speakers will
be heard through the P 5 and your accompanying audio system.
Note: For the highest quality sound playback we recommend leaving your computer’s volume
control at 100%. Then use the volume control on your P 5 to set the listening level.
Audio Output Connections
Left and Right Main Output Jacks (Balanced and Unbalanced)
The Main Output Jacks are the primary outputs that connect to the inputs on your power
amplifier. Both RCA (unbalanced) and XLR (balanced) connections are provided.
Subwoofer Outputs (Balanced and Unbalanced)
The P 5 provides convenient, high quality connections for one or more subwoofers. All of the
subwoofer outputs carry the same mono signal. This mono signal can be full range or crossed
over depending on the setting of the Low Pass crossover.
Record Out Jacks
The Record Out jacks connect to your audio recorder’s record/input jacks. When you select an
Input the signal from the corresponding source component is available at the Record Out jacks
whenever the P 5 is turned on. It is a fixed level signal that is unaffected by volume, balance,
tone settings, audio mute or crossover settings.
Note: When you select the Bypass Input, there is no signal available at
the Record Out jacks. The P 5 does not offer simultaneous
monitoring of a recording while you are making it.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Subwoofer Setup
There are two important steps in setting up your sub(s). These are crossover setup and level setup.
Subwoofer Crossover Setup
You will want to turn off the crossover built into your subwoofer since the P 5 has its own crossovers
and leaving both crossovers on would result in double filtering. Most subwoofers have a switch to
accomplish this. This switch is sometimes called “Bypass”, “Home Theater” or simply “Crossover
Off.” If your subwoofer’s crossover cannot be switched off, set it to its highest frequency. Now
follow the crossover setup section of this manual for the proper settings on the P 5.
Subwoofer Level Setup
To set the proper subwoofer level, first set the P 5’s front panel Sub Level control to the 12 o’clock
(0 dB) position and then play a variety of music. Adjust the level control built into your subwoofer
until the bass level sounds balanced. Now, whenever you want to fine tune your subwoofer level
you can simply use the P 5's front panel Sub Level control instead of walking over to your sub,
bending down and reaching behind it to adjust its level control.
Main and Subwoofer Crossover Setup
The P 5 is equipped with adjustable Low Pass and High
Pass crossovers. Crossovers are filters that allow certain
frequencies to pass while blocking other frequencies.
A Low Pass filter permits low frequencies to pass and
blocks high frequencies. A high pass filter permits only
high frequencies to pass and blocks low frequencies.
80Hz is the best starting frequency for both the High and
Low Pass crossovers if you are using a subwoofer and
are not sure where to set the crossover frequency. If you
are not using a subwoofer, set the Main Output Crossover
switch to the Off position. Both XLR (balanced) and RCA
(unbalanced) outputs are affected by the crossover
settings.
Low Pass Crossover (Subwoofer Outputs)
The low pass crossover allows only low frequencies to be output at the P 5 Subwoofer output
jacks and then played by your subwoofer(s).
Note: If your subwoofer has a built-in crossover that cannot be switched off, set
it to its highest frequency to minimize the negative effects on bass
response from filtering in the P 5 and again in the subwoofer.
High Pass Crossover (Left and Right Main Outputs)
The High Pass crossover for the Left and Right Main outputs allows you to keep low
frequencies from going to your main L and R speakers. This can be particularly useful if you
are using small speakers (typically their woofers are 6.5” inches or smaller) and you have a
subwoofer. The most common settings are between 50Hz and 80Hz. If you are not using a
subwoofer you will get the best results by turning the High Pass crossover off or setting it to
under 40Hz. If you want your L and R speakers to operate full range with no frequencies
blocked set the High Pass crossover switch to its Off position.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Crossover Setup (Continued)…
Crossover On/Off Switches:
Sub Output Crossover Off
Full Range signals will be sent to the sub. You will need to adjust the
crossover frequency on the crossover that is built into your subwoofer.
Sub Output Crossover On
The highest frequency going to the Sub is determined by the setting of the
Low Pass frequency knob.
Main Output Crossover Off
Full Range signals will be sent to the Left and Right speakers.
Main Output Crossover On
The lowest frequency going to the Left and Right speakers is determined by
the setting of the High Pass frequency knob.
Crossovers and the Bypass Input
The High and Low Pass Crossovers are always off when the Bypass Input is selected. In this
case the high and low pass filters are not active because you will want to use the bass
management you already selected in your surround sound receiver’s setup menu.
Where to start with Crossover settings
If you don’t know where to set the High and Low Pass Crossovers, these settings are a good place
to start. From here you can experiment until you find a combination that sounds best to you:
No subwoofer
Set the High Pass Crossover switch to Off
The Low Pass Crossover will not be used so this setting does not matter
When using one or more subwoofers and your Left and Right speakers'
woofers are 6.5” or smaller
Set the High Pass Crossover switch to On and the frequency knob to 80Hz
Set the Low Pass Crossover switch to On and the frequency knob to 80Hz
When using one or more subwoofers and your Left and Right speakers'
woofers are larger than 6.5”
Set the High Pass Crossover switch to On and the frequency knob to 50Hz
Set the Low Pass Crossover switch to On and the frequency knob to 50Hz
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn On Options
For convenience, there are three ways the P 5 can be turned on and off:
Manual - Press the On-Off button on the front panel or the On and Off buttons on
the remote control.
Automatic - When a 12V trigger voltage is applied to the 12V input jack.
Automatic - Whenever the P 5’s AC power source is live.
Note: When either automatic turn on option is selected the front panel
On-Off button is disabled so that power on/off is determined solely
by the triggering device or live AC power.
Turn On Options Switch:
Manual Position
When the Turn On Options switch is in its Manual position, the Turn On Options automatic
functions are disabled and the P 5 must be turned on and off manually by pressing the On-
Off button on its front panel every time you wish to use your audio system.
12V Position (Automatic on/off)
When the Turn On Options switch is set to its 12V position, the P 5 is turned on and off only
with an external +9 V to + 12 V voltage from your preamp or AV Receiver. When the external
voltage ceases the P 5 will turn off immediately. The 12V switch position disables the front
panel On-Off button.
AC Power Trigger
The P 5 will turn on automatically when its AC power source is switched on.
Note: When the Auto Turn On switch is set to 12V or AC the front panel
On-Off button and remote control On and Off buttons are disabled.
3.5mm Mini Jack and 2.5mm Sub-mini Jacks
Some models of Parasound power amplifiers and preamplifiers use 2.5mm “sub-mini” trigger jacks.
To use the P 5 with these models we include a trigger wire with a 3.5mm plug at one end and a
2.5mm plug at the other end.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Rear Panel Connections
IR Input
Your P 5 is compatible with most popular infrared repeater systems for remote control operation
from another room or when the P 5 is installed in a cabinet where its remote handset signals
cannot reach its front panel remote control sensor. The External Remote Input connector is a
standard 1/8” (3.5 mm) mono “mini” jack. The center conductor (plug tip) is for signal and the outer
conductor (plug sleeve) is for ground. Your Authorized Parasound dealer or custom installer can
recommend a compatible IR repeater system.
IR Loop Output
The loop output offers a convenient way to daisy chain an IR signal to another piece of equipment.
Whatever IR control signal is present at the rear panel IR Input jack will also be present at the IR
Loop Out jack.
AC Power Cord
The AC cord supplied with your P 5 is a high quality IEC type cord. If possible, plug your P 5 into
the same AC outlet that your source components and power amplifier are plugged into. If different
AC outlets are used for the P 5 and these other components the ground potential may be higher or
lower between the outlets, resulting in audible hum.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Controls
On-Off Button
A soft blue glow surrounds the On-Off button when the P 5 is turned off. Push the On-Off
button once to turn on and the blue glow will get brighter. When the P 5 is turned on, the Input
indicator and Mute button will illuminate blue. Push the On-Off button again to turn it off.
Note: The front panel On-Off button and remote control On and Off buttons are
disabled when the rear panel Turn On Options switch is set to 12V or AC.
Headphone Output
The headphone jack accepts a 1/8” (3.5 mm) stereo mini plug. The Left, Right and Sub
outputs are muted when a headphone plug is inserted into this jack. The L and R Record out
jacks are not muted.
Note: Please note the volume level before unplugging your headphones to avoid
unexpected high level sound that could damage your speakers.
Aux Input
For your convenience there is an input for a portable MP3 player (or smart phone) on the front
panel. Connect the included cable with 3.5mm stereo plugs between the portable player or
smart phone’s headphone jack and the P 5’s Aux input jack. The Aux input has an additional
gain stage that boosts the input signal by 12dB so that the volume level will remain consistent
as you listen to your other source components. For the best results set your portable player’s
volume to at least 75% of its maximum.
Bass and Treble Knobs
These offer precision adjustment of tonal balance. You will find that very slight adjustments
can add a degree of warmth, richness, clarity and “air.” However, greater adjustments may
obscure musical detail, and even risk overloading your speakers. The Bass and Treble
Controls are only active when the blue light surrounding the Tone button is illuminated. The
Bass and Treble controls affect both the Main Outputs and the Subwoofer outputs.
Tone Button
By pressing this button, you can turn off the Bass and Treble tone controls, thereby completely
bypassing the tone control circuitry. This will improve sonic purity by eliminating the small
amount of noise and distortion inherent in tone control circuits. The tone controls can also be
turned on and off from the remote control.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Controls (Continued)…
Input Knob
Rotating the Input selector will cycle through all of the inputs. The front panel LED under each
input will indicate when it is selected.
Sub Level Knob
The Sub Level control knob adjusts the subwoofer level. The sub level can be adjusted
between -10 dB and +10 dB, relative to the L and R channels. When the control knob is in the
12 o’clock position the sub level boost is 0 dB. When you first set up your subwoofer you
should set this control to 12 o’clock (0 dB) and then play some music. Adjust the level control
built into your subwoofer until it sounds balanced. Now, whenever you want to fine tune your
subwoofer level you can simply use the front panel Sub Level control instead walking over to
your sub and bending over to adjust the level control on the subwoofer.
Note: The Sub Level knob does not adjust the Sub level when the Bypass Input is selected.
Balance Knob
Adjusting left and right channel balance is helpful to compensate for speaker placement, room
acoustics or if your power amplifier’s gain isn’t identical for both channels.
Volume Knob
Your P 5 uses a high quality Alps potentiometer to adjust the master volume level. The
potentiometer is motorized for remote control use.
Mute Button
Pressing the Mute button once will mute the signal at all of the Out jacks except the Record
Out. The Mute button will turn red while mute is engaged. Press the Mute button a second
time to cancel mute. The Mute will be automatically canceled if you press the volume up or
down buttons on the remote.
Note: Mute is not canceled when you turn the front panel Volume knob. Refrain from
moving the Volume knob when the P 5 is muted to avoid a loud surprise when it is
unmuted.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Functions
The P 5 remote control has a maximum range of approximately 20 - 25 feet (6 - 7.5 meters).
Use only AAA alkaline batteries in the handset and insert them according to the + and – polarity
markings in the battery compartment.
On and Off Buttons
These separate buttons enable programming
unambiguous “hard” off and on commands into a system
controller or to create a macro sequence for a learning-
type remote control.
Note: The On and Off buttons are disabled when the
rear panel Turn On Options switch is set to 12V or AC.
Mute Button
Pressing the Mute button once mutes the signal at all of
the Out jacks except the Record Out. The Mute button on
the front panel will illuminate red while mute is engaged.
Press the Mute button a second time to cancel mute.
Volume ▲ and ▼ Buttons
These buttons control the rotation of the motorized Volume
knob to increase and decrease listening volume levels.
Tone On and Off Buttons
By pressing the Tone On button you engage the tone
control circuit with the boost or cut determined by the
setting of the front panel Bass and Treble knobs.
By pressing the Tone Off button you can turn off the Bass
and Treble tone control circuit, thereby completely
bypassing the tone control circuitry. This will improve
sonic purity by eliminating the small amount of noise and
distortion inherent in tone control circuits. The tone
controls can also be turned on and off from the front panel.
Note: The remote control cannot make Bass and Treble
adjustments. Tone adjustments are only made with the
Bass and Treble knobs on the P 5’s front panel.
Source Input Buttons
Press the input button of the source that you wish to hear.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintaining Your P 5
Your P 5 requires no periodic maintenance and has no user serviceable parts inside.
To avoid risk of electric shock do not remove the top cover. To keep it clean use only a soft
cloth moistened with a few drops of clear water or Windex. Never use any solvents or
abrasives. The remote control handset batteries should be removed whenever it will be
unused for an extended period. Remove the battery cover annually to inspect and remove
leaking batteries.
Ground Loops - Eliminating Hum and Buzz
Audible hum and buzzing noises in a system are usually related to issues with the
component grounds. Ground (sometimes called common) is a point of reference for voltages
in virtually all audio and video components. Ground is supposed to remain at zero volts while
the audio signal swings positive (voltage above ground) and negative (voltage below ground).
If ground isn’t at zero, there can be an audible 60 Hz hum (or 50 Hz hum in regions with 50 Hz
AC). The harmonics of these frequencies (120 Hz, 240 Hz, 480 Hz or 100 Hz, 200 Hz, 400 Hz)
may add buzz in addition to the hum.
The ideal of zero voltage ground for all the components in a system is practically
impossible, because some resistance between the ground points of different components is
inevitable. By keeping components close together with their power cords plugged into a
common AC outlet or power strip, you’ll avoid the problems created by resistance in the
house’s wiring.
Hum and buzz is also caused when unwanted voltage flows through multiple
component ground points called ground loops. Here are three tips to avoid ground loops:
1. Your Cable TV receiver box might require a Cable TV ground isolator. To determine if this
is the case, unplug your incoming cable signal and see if the buzz/hum goes away.
2. Plug your subwoofer and amplifier(s) into the same outlet as the P 5.
3. When rack mounting, always use the insulated “shoulder” washers. These break the ground
loops caused by metal-to-metal contact between the rack, the components, and their rack-
mount bolts.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Remedies
Why is there no sound from the speakers?
- Is the AC power live? You should see a faint red glow around the Power button even when
the unit is turned off.
- Check that input and output cables are secure at both ends.
- Make sure your P 5 is switched to the correct input.
- Make sure your power amplifier is powered on.
The P 5 won’t turn on
- Make sure the rear panel Turn On Options Switch is set to the Manual position.
- Make sure the rear panel master power switch is turned on.
-Make sure the unit is plugged into a live AC receptacle
The P 5 won’t turn off
- Make sure the rear panel Turn On Options Switch is set to the Manual position.
I can hear a background hum from the speakers
- Read the section on ground loops in this manual.
- Move audio cables and AC cords away from each other (while power is off).
- Try to route audio cables and AC cords perpendicular to each other (while power is off).
- Make sure insulating shoulder washers are used if unit is rack mounted.
- Insure that the power amps and the P 5 are plugged into the same AC outlet.
- Try unplugging the incoming Cable TV line. If the noise goes away you need a cable TV
ground isolator.
- Try plugging your subwoofer into the same outlet as the P 5 and power amp.
- The turntable ground wire must be attached to the GND terminal.
The sound is distorted and weak
- Make sure the gain of the power amp is not set too low.
- Are you trying to use P 5 with a turntable? Make sure you have set the phono selector switch
to the correct cartridge type. Is the turntable's tracking force adjusted correctly for its cartridge?
- Make sure the stereo power amp’s stereo/mono switch is set to stereo.
When I use the Bypass Input the sound is very loud and cannot be turned down.
The Bypass input should never be connected directly to a source component (CD, DVD, Tape
deck, etc.). It should only be used in conjunction with a surround sound receiver or controller.
The volume control on the surround sound equipment should be used to adjust the volume
level when the P 5 Bypass input is selected.
What is the Bypass Input?
The Bypass input jacks are used to incorporate the P 5 into a surround sound system. This
enables you to use the power amplifier (or two channels of a multi-channel amp) driving your
Left and Right front speakers and subwoofer(s) with stereo sources connected to the P 5 and
with your surround sound system.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Are You Having Difficulty?
Repair or Service
Call your Parasound dealer first. If the dealer can’t help you with your problem we encourage
you to call Parasound’s Technical Service Department at 415-397-7100, Monday - Friday,
8am - 4pm Pacific Time. We can suggest other diagnostic tests you can easily perform.
If we determine that your P 5 should be returned to Parasound or an Authorized Parasound
Warranty Center for inspection and possible servicing, we will provide the location of a
warranty center near you or shipping instructions for the unit’s return to Parasound.
Before You Return Any Unit to Parasound for Service
Before you send your unit to Parasound, you will need to obtain a specific Return
Authorization (RA) number and shipping instructions from Parasound’s Technical Department.
The RA number must be clearly marked on the outer carton. Use the original factory packing
materials and arrange adequate insurance to cover its value. You must include a copy of your
purchase receipt, since this document establishes the validity of this unit’s warranty. Warranty
repairs are only performed by Parasound or Parasound Authorized warranty centers when
your purchase receipt is from a Parasound Authorized Dealer or Parasound Authorized
Reseller.
Shipments Will Be Refused by Parasound Under the Following Conditions:
1. Unit was sent without the Parasound-assigned RA number marked on the carton.
2. Unit was sent in an unsuitable shipping carton and packing inserts and is likely to have
been damaged in transit.
3. Unit has inadequate packing materials and is likely to have been damaged in transit.
Wrapping the P 5 with bubble wrap will not protect it during shipment.
4. Unit was shipped collect for shipping charges. We do not accept collect shipments.
5. Unit was shipped via the US Postal Service.
6. Unit was sent to an address other than the address instructed by our Technical Department.
Warranty Repair
Please read your accompanying Parasound Limited Warranty carefully to understand the
applicable rights and limitations. This section provides instructions for obtaining repairs, both for
units covered under the Parasound Limited Warranty and for units or situations which are
Unit is not eligible for repair under the terms of the Parasound warranty if:
1. Unit was not purchased from a Parasound Authorized Dealer.
2. You do not have the original bill of sale or sales receipt from a Parasound Authorized Dealer.
3. You are not the original owner. The Parasound warranty is not transferable.
4. Unit’s serial number was removed, modified, or defaced.
5. Unit shows evidence of abuse and/or misuse.
6. Unit was modified in any way.
7. A prior repair was attempted by an unauthorized repair station.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Frequency Response
Hi & Low Pass Crossover Slope
10 Hz - 100 kHz, +0/-3 dB
12 dB / Oct
Total Harmonic Distortion
DC Trigger Requirements
< 0.01 %
+9 Vdc to +12 Vdc, 2 mA
Crosstalk
XLR Pin Identification
1 = Ground (Shield)
2 = Positive
> 70 dB at 20 kHz
Input Sensitivity
3 = Negative (Return)
300 mv: 1 Volt Out
Total Gain: 10 dB
Maximum Output: 7 Volts
Dimensions
Width: 17-1/4” (437 mm)
Depth: 13-3/4” (350 mm)
Height, with feet: 4-1/8” (105 mm)
Height, without feet: 3-1/2” (89 mm)
Input Impedance
Unbalanced: 24k Ω
Balanced: 100k Ω per leg
Net Weight
Output Impedance
Unbalanced: 100 Ω
Balanced: 470 Ω per leg
14 lb. (6.3 kg)
Shipping Weight
21 lb. (9.5 kg)
S/N Ratio - Line Inputs 1- 5
> 108 dB, input shorted, IHF A-weighted
> 88 dB, input shorted, unweighted
Power Requirement
Standby: 0.5 Watts
Power On: 12 Watts
100-250 Volts, 50-60 Hz (Automatic)
S/N Ratio - DAC Inputs
> 108 dB, input shorted, IHF A-weighted
> 90 dB, input shorted, unweighted
S/N Ratio - Phono Inputs
MM > 80 dB, input shorted, IHF A-weighted
MM > 70 dB, input shorted, unweighted
MC > 67 dB, input shorted, IHF A-weighted
MC > 55 dB, input shorted, unweighted
Specifications and features subject to change or improvement without notice.
Copyright Parasound Product Inc., 2013
Rev. 1.1
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Parasound Products, Inc. 2250 McKinnon Ave, San Francisco, CA 94124
22
Download from Www.Somanuals.com. All Manuals Search And Download.
|