Hotwire® ReachDSL™ v1 (MVL®) Modem,
Model 6310-A4, with Inline Phone Filter
Installation Instructions
Document Number 6310-A2-GN12-00
September 2001
Contents
Getting Started ..............................................................................................
Power-On ......................................................................................................
Troubleshooting .............................................................................................
Increasing the Number of End-User Systems .............................................. 10
Cables & Connectors .................................................................................... 11
Optional ReachDSL Modem Wall Placement ............................................... 13
Technical Specifications for Hotwire 6310 ReachDSL v1 Modem ................ 15
Important Safety Instructions ........................................................................ 16
Warranty, Sales, Service, and Training Information ...................................... 21
Hotwire 6310 ReachDSL v1 (MVL) Modem Overview
®
™
®
The Hotwire 6310 ReachDSL version 1 (formerly MVL ) Modem is a component in
the Hotwire ReachDSL System and interoperates with the Hotwire 8310 MVL, or
Hotwire 8312/8314 ReachDSL Card in the DSLAM (Digital Subscriber Line Access
Multiplexer) system. This system provides high-speed Internet or corporate LAN access
over traditional twisted-pair copper telephone wiring.
The ReachDSL technology:
Utilizes an inline phone filter on the ReachDSL modem’s PHONE jack.
Operates over existing copper wire with existing telephone jacks.
Includes a second line pass-through from the ReachDSL modem’s LINE jack to
PHONE jack to accommodate an attached 2-line telephone.
Provides rate adaptive data rates to dynamically adapt and allocate bandwidth to
optimize applications.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Phone Filter
Depending on the type of phone handset and the quality of the home or business wiring,
a phone filter is recommended to minimize background noise during a phone
conversation. An internal phone filter is included with the Hotwire 6310 ReachDSL v1
Modem. If additional telephones are used on the same phone line as the ReachDSL
modem, install one phone filter on each telephone.
There are two Hotwire phone filters:
Hotwire 6035 Universal Phone Filter is designed for use with a tabletop phone.
Hotwire 6040 Universal Wall Jack Phone Filter is designed for use with a wall
phone.
Customer
Premises (CP)
ReachDSL
Modem
6035
Phone Filter
RJ11
Wall
Jack
PO
W
ER
ET
HE
RN
ET
PH
ON
E
LIN
E
ReachDSL Modem
RJ11
Wall Jack
6040
FAX
PO
W
ER
ET
HE
RN
ET
PH
ON
E
LIN
E
Wall Jack
Phone
Filter
01-17006
Product-Related Documents
To install a phone filter, refer to the appropriate document:
Document
Number
Document Title
6035-A2-GN11 Hotwire 6035 Universal Phone Filter Installation Instructions
6040-A2-GN11 Hotwire 6040 Universal Wall Jack Phone Filter Installation
Instructions
Contact your sales or service representative to order additional product documentation.
Select Library → Technical Manuals → Hotwire DSL Systems.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Before beginning your modem’s installation, make sure that you have all the equipment
that you need.
Package Checklist
Verify that your package contains the following:
❑ Hotwire 6310 ReachDSL v1 Modem
❑ DSL interface cable with RJ11 connectors
❑ Power cord with power transformer
Wiring and Cables You Need
The following wiring and standard connectors are used with this product:
❑ Standard RJ11 (or RJ14) wall jack for the ReachDSL modem cabling.
❑ Standard Ethernet 8-pin, non-keyed modular plug for a PC or workstation. An
Ethernet straight-through or crossover cable is used.
—
—
Refer to Installing the Hotwire 6310 ReachDSL v1 Modem on page 5 for
Ethernet installation details.
Refer to Cables & Connectors on page 11 for ReachDSL modem and Ethernet
cable pin assignments.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Hotwire 6310 ReachDSL v1 Modem
Procedure
1. If a telephone is connected at the RJ11
RJ11
wall jack where the modem will be installed,
Wall Jack
unplug the telephone line from the wall jack.
2. Connect a telephone to the modem.
(Optional – go to Step 3 if you are not
connecting a telephone to the ReachDSL
modem.)
Plug the existing telephone interface cable
01-17015a
that was unplugged in Step 1 into the jack
labeled PHONE.
3. Use the supplied RJ11 6-pin interface cable for the LINE connection. Insert one end
of the cable into the jack labeled LINE. Insert the other end of the cable into the
RJ11 wall jack.
PHONE
LINE
PO
W
ER
ETHERNET
HONE LINE
RJ11
Wall Jack
RJ11
6-pin
Interface Cable
01-17015
NOTE:
If you are installing a POTS splitter with another telephone, connect the
telephone to the jack labeled PHONE, then connect the jack labeled LINE to a
wall jack. Do NOT plug any cable into the POTS splitter jack labeled either
MODEM or DSL. In particular, make NO connections between a POTS splitter
and the modem.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the cable
into the jack labeled ETHERNET.
—
Use a straight-through cable and connect the other end to an Ethernet hub.
(To connect to a hub’s Uplink connection, use an Ethernet crossover cable).
Ethernet
Line
PO
WER
THERNET
PHLINE
Ethernet
Hub
1
2
3
4
5
6
7
8
Ethernet
Straight-Through
Cable
01-17008
–or–
—
Use an Ethernet crossover cable and connect the other end to a PC with an
Ethernet Network Interface Card (NIC) installed.
Ethernet
Line
PO
WER
THERNET
PHLINE
PC with Ethernet
Network Interface
Card
Ethernet
Crossover
Cable
01-17009
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Insert the supplied power cord’s round end into the jack labeled POWER. Plug the
transformer into an AC outlet.
Power
Jack
PO
W
ER
HERNET
PHLINE
Transformer
or
01-17010
The ReachDSL modem hardware installation is now complete. When the power cord is
installed, the ReachDSL modem goes through a power-on self-test.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Power-On
When power is applied, the ReachDSL modem performs self-diagnostics and the PWR
LED is on. The self-diagnostics includes a power-on self-test and all of the LEDs turn on
for one second.
Power – green
Alarm – red
Test – yellow
DSL Line – green
Transmit/Receive – green
Ethernet Link – green
PWR
ALM
TST
LINE TX/RX
ETHERNET
ReachDSL
01-17003
Status LEDs
All of the LEDs turn on and off during the power-on self-test. After a successful self-test,
the LEDs should appear as indicated in BOLD in the Condition column below.
LED
PWR
ALM
Condition Status
ON
ReachDSL modem has power.
OFF
No active alarms.
ON
An alarm condition exists.
TST
OFF
No active tests.
ON
The TST LED is on during the power-on self-test and
during a test initiated by the service provider.
LINE
TX/RX
ON
The DSL link is active and ready to transmit and receive
data.
OFF
The DSL link has not been established.
ON
The modem is not transmitting or receiving data.
OFF
ETHERNET ON
OFF
The Ethernet connection to the Ethernet hub or PC is
active.
No Ethernet 10BaseT device is detected.
Refer to Troubleshooting on page 9 for LED indications requiring action.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
LED Symptom
Action
All LEDs are on.
If LEDs remain on after ten minutes, the modem is not
functional. Contact the service provider.
ALM LED remains
on.
The power-on self-test may have failed. Unplug the unit and
reapply power. If the alarm LED is still on, contact the service
provider.
are blinking.
not in progress or the LEDs continue blinking after ten minutes,
contact the service provider.
Ethernet LED is off. Verify that the Ethernet cable is securely installed at both ends,
and at least one PC is connected and powered on.
Verify that the correct straight-through or crossover cable is
installed. Refer to Installing the Hotwire 6310 ReachDSL v1
Modem on page 5.
LINE LED is off.
Verify that the LINE cable is securely installed on both ends. If
the problem continues, contact the service provider.
Verify that the line has dial tone. If there is no dial tone, contact
the service provider.
LINE LED is on and The DSL link has been established but there is no data
there is no data
transmission.
transmission. Verify the Ethernet connection. If the problem
persists, contact the service provider.
LINE and Ethernet
LEDs are on and
there is no data
transmission.
The DSL line and Ethernet links have been established but
there is no data transmission. If the problem continues, contact
the service provider.
PWR LED is off.
Check that the power cord is securely installed on both ends.
If no LEDs are on, the power supply may be defective. Test the
outlet to verify power. If the problem persists, contact the
service provider.
If other LEDs are on, the PWR LED may be burned out. Unplug
the unit and reapply power; watch all LEDs during the power-on
self-test to verify if the PWR LED is functioning.
TST LED is on.
A test initiated by the service provider may be active. Wait five
minutes. If the TST LED does not go off, contact the service
provider.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
To improve data transmission throughput and minimize background noise during a
telephone conversation, make sure that:
The Hotwire 6310 ReachDSL v1 Modem is always powered on, even when not in
use, and
A Hotwire phone filter is installed on every telephone on the same line as the
Hotwire 6310 ReachDSL v1 Modem (see Phone Filter on page 3).
HomeLink (for ReachDSL v1 Modems Only)
HomeLink is a feature that provides peer-to-peer communications for PCs attached to
different Hotwire 6310 ReachDSL v1 modems at the customer premises.
For example, PCs that are not connected to the same physical Ethernet LAN can now
take advantage of the resources of the primary office computer. With the Microsoft
Windows operating system, multiple end-user systems can share resources, including:
File sharing
Print sharing
Secondary computer backup
To enable the sharing of resources and review security considerations, see Microsoft’s
In this example of HomeLink, the PC in the family room could use the office printer.
Office
Family Room
ReachDSL v1
Modem
FAX
PO
ReachDSL v1
Modem
W
ER
ET
HE
RN
ET
PH
ON
E
LIN
E
Hub
RJ11
Wall
Jack
PO
W
ER
ET
HE
RN
ET
PH
ON
E
LIN
E
RJ11
Wall
Jack
Ethernet
Cable
Printer
01-17012
Increasing the Number of End-User Systems
A single end-user system is attached to the Hotwire 6310 ReachDSL v1 Modem by
using an Ethernet crossover cable. To increase the number of end-user systems,
connect all the PCs to an Ethernet hub using a straight-through cable.
On one line, the ReachDSL v1 system provides the capability to use up to four Hotwire
6310 ReachDSL v1 modems and 32 end-user systems in any combination.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cables & Connectors
This section is reference information.
Standard twisted-pair CAT3 or better cables are recommended.
The LINE and PHONE interface connectors
use 6-pin, non-keyed modular plugs. RJ11 or
RJ14 6-pin connectors can be used.
6-Pin
RJ11 Plugs
Line & Phone Connectors
Pin # Function
1
2
3
4
5
6
Not used
Ring 2 (optional)
DSL Ring 1
DSL Tip 1
Pin #6
Pin #1
Tip 2 (optional)
Not used
98-15304a
The LINE and PHONE jack pinouts are either filtered or unfiltered for POTS.
PHONE Jack Pinouts
LINE Jack Pinouts
Pin # 3, 4 Filtered for POTS
Pin # 2, 5 2nd POTS unfiltered
Pin # 3, 4 DSL and POTS
Pin # 2, 5 2nd line pass-through
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The Ethernet interface connector uses an 8-pin, non-keyed modular plug.
—
To connect the ReachDSL modem to an
Ethernet hub, use the straight-through
connection.
Ethernet
Cable
8-Pin Straight-through Connection
Pin # Function
1
2
3
10BaseT TX D+
10BaseT TX D–
10BaseT RX D+
8-Pin
Plug
4 & 5 Not used
6
10BaseT RX D–
Pin #8
7 & 8 Not used
Pin #1
98-16055a
–or–
—
To connect the ReachDSL modem directly to a PC with an Ethernet NIC card,
use an Ethernet crossover cable.
8-Pin Ethernet Crossover Cable
Function Pin #
Pin # Function
10/100BaseT TX D+
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
10/100BaseT TX D+
10/100BaseT TX D–
10/100BaseT RX D+
Not Used
10/100BaseT TX D–
10/100BaseT RX D+
Not Used
Not Used
Not Used
10/100BaseT RX D–
Not Used
10/100BaseT RX D–
Not Used
Not Used
Not Used
99-16518
Pin #1/2 = Orange/White
Twisted Pair
Pin #3/6 = Blue/White
Twisted Pair
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional ReachDSL Modem Wall Placement
ReachDSL modem can also be mounted on a wall. To mount the modem, you will need:
❑ Two slotted-head #6 self-threading screws with plastic anchors
❑ Drill and 3/16" drill bit for the plastic anchors
❑ Screwdriver
A template with the dimensions for the two screws is provided. See ReachDSL Modem
Hardware Template on page 14.
Procedure
To mount the Hotwire 6310 ReachDSL v1 Modem:
1. Use a drill to install the plastic anchors.
2. Use a screwdriver to install the screws. Do not install the screws flush with the wall.
Leave enough clearance to hang the modem housing from the screws.
Wall
Fasteners
Hotwire
ReachDSL
Modem
01-17004
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications for Hotwire 6310 ReachDSL v1
Modem
Item
Specification*
Height x Width x Depth
Weight
1.46" x 5.72" x 4.33" (3.71 cm x 14.54 cm x 11.00 cm)
0.45 lb. (0.20 kg)
Power
Class 2 Transformer normal Input: 100 VAC (+10%), 50 Hz;
service input voltage range
120 VAC (+10%), 60 Hz; or
230 VAC (+10%), 50/60 Hz
Output: 5 VDC nominal, minimum 0.6A (SELV)
Approvals
FCC Part 15
CISPR 22
Class B digital device
Class B
Other Certifications
Refer to equipment’s label for approvals on product
Physical Environment
Operating temperature
Storage temperature
Relative humidity
32°F to 104°F (0°C to 40°C)
–22°F to 158°F (–30°C to 70°C)
5% to 95% (noncondensing)
Shock and vibration
Withstands normal shipping and handling
Heat Dissipation
2.35 watts at 5.0 VDC (nominal input voltage)
Interface Connectors
Line and Phone Interfaces
Ethernet Type II Frame
RJ11 or RJ14 6-pin
10BaseT 8-pin
* Technical Specifications subject to change without notification.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
!
Important Safety Instructions
1. Read and follow all warning notices and instructions marked on the product or
included in the manual.
2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable
operation of the product and to protect it from overheating, these slots and
openings must not be blocked or covered.
3. Do not allow anything to rest on the power cord and do not locate the product where
persons will walk on the power cord.
4. Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous high voltage points or other risks. Refer all servicing to
qualified service personnel.
5. General purpose cables are used with this product for connection to the network.
Special cables, which may be required by the regulatory inspection authority for the
installation site, are the responsibility of the customer. Use a UL Listed, CSA
certified, minimum No. 24 AWG line cord for connection to the Digital Subscriber
Line (DSL) network.
6. When installed in the final configuration, the product must comply with the
applicable Safety Standards and regulatory requirements of the country in which it
is installed. If necessary, consult with the appropriate regulatory agencies and
inspection authorities to ensure compliance.
7. A rare phenomenon can create a voltage potential between the earth grounds of
two or more buildings. If products installed in separate buildings are
interconnected, the voltage potential may cause a hazardous condition. Consult a
qualified electrical consultant to determine whether or not this phenomenon exists
and, if necessary, implement corrective action prior to interconnecting the products.
8. Input power to this product must be provided by one of the following: (1) a UL
Listed/CSA certified power source with a Class 2 or Limited Power Source (LPS)
output for use in North America, or (2) a certified transformer, with a Safety Extra
Low Voltage (SELV) output having a maximum of 240 VA available, for use in the
country of installation.
9. In addition, since the equipment is to be used with telecommunications circuits, take
the following precautions:
—
—
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
—
Never touch uninsulated telephone wires or terminals unless the telephone line
has been disconnected at the network interface.
—
—
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
—
Do not use the telephone to report a gas leak in the vicinity of the leak.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CE Marking
When the product is marked with the CE mark on the equipment label, this
demonstrates full compliance with the following European Directives:
Directive 73/23/EEC – Council Directive of 19 February 1973 on the harmonization
of the laws of the member states relating to electrical equipment designed for use
within states relating to electrical equipment designed for use within certain voltage
limits, as amended by Directive 93/68/EEC.
Directive 89/336/EEC – Council Directive of 3 May 1989 on the approximation of
the laws of the member states relating to Electro-Magnetic Compatibility (EMC), as
amended by Directive 93/68/EEC.
!
CANADA – EMI NOTICE:
This Class B digital apparatus meets all requirements of the Canadian
interference-causing equipment regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
réglement sur le matérial brouilleur du Canada.
Japan – Notices
This is a Class B product based on the standard of the Voluntary Control Council
for Interference from Information Technology Equipment (VCCI). If this is used
near a radio or television receiver in a domestic environment, it may cause radio
interference. Install and use the equipment according to the instruction manual.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2
and 15 of the Federal Communications Commission’s Rules. This compliance
information statement pertains to the following products:
Trade Name:
Hotwire
Model Number: 6310-A4-200
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
The name, address, and telephone number of the responsible party is given below:
Paradyne Corporation
8545 126th Avenue North
Largo, FL 33773-1502
Phone: (727) 530-2000
The authority to operate this equipment is conditioned by the requirement that no
modifications will be made to the equipment unless the changes or modifications are
expressly approved by Paradyne Corporation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Government Requirements
Certain governments require that instructions pertaining to connection to the telephone
network be included in the installation and operation manual. Specific instructions are
listed in the following sections.
United States – Notice to Users of the Telephone Network
1. This equipment complies with Part 68 of the FCC rules. On the equipment is a label
that contains, among other information, the FCC registration number and Ringer
Equivalence Number (REN) for this equipment. The label is located on the bottom
of your modem.
2. The Hotwire 6310 ReachDSL v1 Modem connects to the Public Switched
Telephone Network (PSTN) using the Universal Service Order Code (USOC)
RJ11C or RJ14C.
3. The REN is used to determine the quantity of devices which may be connected to
the telephone line. Excessive RENs on the telephone line may result in the devices
not ringing in response to an incoming call. In most, but not all areas, the sum of the
RENs should not exceed five (5.0). To be certain of the number of devices that may
be connected to the line, as determined by the total RENs, contact the telephone
company to determine the maximum RENs for the calling area.
4. If the modem causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required.
But if advance notice is not practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
5. The telephone company may make changes in its facilities, equipment, operations,
or procedures that could affect the operation of the equipment. If this happens, the
telephone company will provide advance notice in order for you to make the
necessary modifications in order to maintain uninterrupted service.
6. If you experience trouble with this equipment, please contact your sales or service
representative (as appropriate) for repair or warranty information. If the product
needs to be returned to the company service center for repair, contact them directly
for return instructions using one of the following methods:
—
—
Telephone: Call our automated system to receive current information via fax or
to speak with a company representative.
Within the U.S.A., call 1-800-870-2221
Outside the U.S.A., call 1-727-530-2340
If the trouble is causing harm to the telephone network, the telephone company
may request that you remove the equipment from the network until the problem is
resolved.
7. The user is not authorized to repair or modify the equipment.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
8. This equipment cannot be used on public coin service provided by the telephone
company. Connection to Party Line Service is subject to state tariffs. (Contact the
state public utility commission, public service commission or corporation
commission for information.)
9. An FCC compliant telephone cord with modular plugs may be provided with this
equipment. This equipment is designed to be connected to the telephone network
or premises wiring using a compatible modular jack which is Part 68 compliant.
Notice to Users of the Canadian Telephone Network
The Industry Canada label identifies certified equipment. This certification means that
the equipment meets telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment Technical
Requirements document(s). The Department does not guarantee the equipment will
operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The equipment
must also be installed using an acceptable method of connection. The customer should
be aware that compliance with the above conditions may not prevent degradation of
service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by
the supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request to
disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.
CAUTION:
Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as
appropriate.
The Ringer Equivalence Number (REN) assigned to each terminal device provides an
indication of the maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the Ringer Equivalence Numbers of all
the devices does not exceed 5.
If your equipment is in need of repair, refer to Warranty, Sales, Service, and Training
Information on page 21.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor directly for
any help needed. For additional information concerning warranty, sales, service, repair,
installation, documentation, training, distributor locations, or Paradyne worldwide office
locations, use one of the following methods:
Telephone: Call our automated system to receive current information by fax or to
speak with a company representative.
—
—
Within the U.S.A., call 1-800-870-2221
Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them to
Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or
in your correspondence. Please include your name and phone number if you are willing
to provide additional clarification.
Trademarks
Hotwire and MVL are registered trademarks of Paradyne Corporation. ReachDSL is a
trademark of Paradyne Corporation. All other products and services mentioned herein
are the trademarks, service marks, registered trademarks, or registered service marks
of their respective owners.
Patent Notification
Hotwire MVL products are protected by U.S. Patents: 4,669,090, 4,744,092, 5,291,521,
5,805,669, and 5,848,150. Other U.S. and foreign patents pending.
Copyright © 2001 Paradyne Corporation. Printed in U.S.A.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢁꢂꢃꢄꢅꢆꢇꢅꢈ"ꢃꢇꢅꢄꢄꢀ
*6310-A2-GN12-00*
Download from Www.Somanuals.com. All Manuals Search And Download.
|