835 HIP SLED SYSTEM
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
USER’S GUIDE
CLASS H
PART # 7339501
REV.B
1
Version: 835109
Revision: 12/09/02
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
Please note:
* Thank you for purchasing the ParaBody 835 Hip Sled System. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
Tools Required forAssembly
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OFTHE HEAD OFTHE BOLT.
BOLT LENGTH
BOLT LENGTH RULER:
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
3
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1’
2’
3’
4’
5’
1
2
3
4
5
6
7’
8’
9’
1 Square = 1’ X 1’
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY
1
DESCRIPTION
BASE
KEY
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
QTY
1
QTY
1
PART #
DESCRIPTION
4 X 14” NON-SKID STRIP
2” SQ. END CAP
PART #
LEA6270501
LEA6405201
LEA6416601
LEA7234801
LEA3114403
LEA3114502
LEA3114702
LEA3114401
LEA3114701
LEA6504909
LEA6506809
LEA7337609
LEA6507709
LEA6507809
LEA6667809
LEA6505910
LEA7337309
LEA7337409
LEA6504410
LEA7337710
LEA6506610
LEA6507010
LEA6521210
LEA6534310
LEA6667910
LEA6509221
LEA6666921
LEA6667321
LEA6500501
LEA6500601
LEA3103101
LEA3103104
LEA3116001
2
PLATFORM SLEEVE
PAD SUPPORT
RIGHT HANDLE
LEFT HANDLE
REAR UPRIGHT
CARRIAGE STOP BAR
LEFT RAIL
8
1
3
1
1
1-1/2” X 3/4” PARAGLIDE
2” SQ. COVER CAP
3/8” WASHER
4
2
1
5
24
8
1
6
1
3/8” LOCK WASHER
3/8” LOCK NUT
7
8
2
8
32
14
8
1
1/2” WASHER
9
RIGHT RAIL
1
1/2” LOCK NUT
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
FOOT PLATE
1
LEA3235501 1/2” LOW HEIGHT LOCK NUT
PLATFORM
2
1
LEA3235204
LEA3235208
LEA3235212
LEA3235218
LEA3235405
LEA3235311
LEA3235313
LEA3235316
LEA3235318
LEA3235320
LEA3110002
LEA6020601
LEA6466901
3/8 X 1” BOLT
3/8 X 2” BOLT
PLATFORMADJUSTMENT
WEIGHT SUPPORT
ADJ. WHEEL BRACKET
PAD STOP
4
1
8
1
3/8 X 3” BOLT
2
2
3/8 X 4-1/2” BOLT
1/2 X 1-1/4” BOLT
1/2 X 2-3/4” BOLT
1/2 X 3-1/4” BOLT
1/2 X 4” BOLT
2
1
CARRIAGE
2
1
SHOULDER PAD
SEAT PAD
6
2
2
1
BACK PAD
8
1
1/2 X 4-1/2” BOLT
1/2 X 5” BOLT
3” DIA. WHEEL
2” DIA. WHEEL
1-1/4 X 5” GRIP
1 X 5” GRIP
2
4
2
4
1-1/4” ROLL PIN
1/2” FLANGE BEARING
1/2” DIA. SPRING PIN
8
2
2
2
1-1/4” SQ. RUBBER BUMPER
2
Hardware bags:
Bag 1= LEA7078609
Bag 3= LEA7078809
Bag 2= LEA7078709
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DO NOT SECURELY TIGHTEN
AT THIS TIME
*
6
28
33
32
1/2 X 3-1/4”
1
41
3/8 X 3” 37
*
23
29
4
26
31
29
3/8 X 3” 37
*
5
FIGURE 1
STEP 1:
• SECURELY assemble the REAR UPRIGHT (6) to the BASE (1) as shown in FIGURE 1 using two 1/2 X 3-1/4” BOLTS (41), four
1/2” WASHERS (32), and two 1/2” LOCK NUTS (33).
• LOOSELY assemble the RIGHT (4) and LEFT HANDLES (5) to the BASE (1) on their respective sides using four 3/8 X 3” BOLTS (37),
eight 3/8”WASHERS (29), and four 3/8” LOCK NUTS (31) (DO NOTSECURELY TIGHTENATTHISTIME)
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
44 1/2 X 5”
1
46
11
33
46
44 1/2 X 5”
FIGURE 2
STEP 2:
• Insert four 1/2” FLANGE BEARINGS (46) into the BUSHINGS on the BASE (1), and four 1/2” FLANGE BEARINGS (46) into
the BUSHINGS on the PLATFORM (11) as shown in FIGURE 2.
• Assemble the PLATFORM (11) between the BUSHINGS on the BASE (1) as shown in FIGURE 2 using two 1/2 X 5” BOLTS (44)
and two 1/2” LOCK NUTS (33). (TIGHTEN THE CONNECTION ENOUGH TO REMOVE THE PLAY, YETALLOWING
THE PLATFORM TO ROTATE FREELY)
STEP 3:
12
• Attach four 1-1/2 X 3/4” PARAGLIDE STRIPS (27) to the end of
the PLATFORM ADJUSTMENT (12), and four 1-1/2 X 3/4”
PARAGLIDE STRIPS (27) to the end of the PLATFORM SLEEVE
as shown in FIGURE 3 using the following steps:
27
• Thoroughly clean all surfaces where the PARAGLIDE
STRIPS (27) are to be attached.
27
• Remove the PARAGLIDE STRIPS (27) from the paper
backing and firmly apply them to all shown surfaces.
47
• SECURELY Assemble one 1/2” DIA. SPRING PIN (47) to the
SPRING PIN HOUSING, on the PLATFORM SLEEVE (2) as
shown in FIGURE 3. (!!! IMPORTANT !!! TIGHTEN THE
2
NUT OF THE SPRING PIN SECURELY)
FIGURE 3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1/2 X 4” 42
11
12
47
1/2 X 4” 42
33
2
1
SECURELYTIGHTEN
HANDLES BOTH SIDES
33
FIGURE 4
STEP 4:
• Assemble the PLATFORM SLEEVE (2) to the BASE (1) as shown in FIGURE 4 using one 1/2 X 4” BOLT (42), and one 1/2”
LOCK NUT (33). (TIGHTEN THE CONNECTION ENOUGH TO REMOVE THE PLAY, YETALLOWING THE PLAT-
FORM SLEEVE TO ROTATE FREELY)
• Pull back the 1/2” DIA. SPRING PIN (47) on the PLATFORM SLEEVE (2) and insert the PLATFORM ADJUSTMENT (12) into
it. Slide the PLATFORM ADJUSTMENT (12) down to the first adjustment hole and release the SPRING PIN (47).
• Assemble the PLATFORM ADJUSTMENT (12) to the PLATFORM (11) as shown in FIGURE 4 using one 1/2 X 4” BOLT (42),
and one 1/2” LOCK NUT (33). (TIGHTEN THE CONNECTION ENOUGH TO REMOVE THE PLAY, YETALLOWING
THE PLATFORMADJUSTMENTTO ROTATE FREELY)
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43 1/2 X 4-1/2”
6
9
18
8
29
30
3/8 X 4-1/2” 38
1
FIGURE 5
STEP 5:
• LOOSELY assemble the LEFT (8) and RIGHT RAILS (9), along with the SEAT PAD (18) to the BASE (1) as shown in FIGURE 5
using two 3/8 X 4-1/2” BOLTS (38), two 3/8” LOCK WASHERS (30), and two 3/8” WASHERS (29). Temporarily assemble the
RAILS to the REAR UPRIGHT (6) using two 1/2 X 4-1/2” BOLTS (43) to aid in the assembly of this step.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
16
34 LOW
HEIGHT
25
32
26
20
32
1/2 X 4-1/2” 43
FIGURE 6
STEP 6:
• Insert four 2” SQ. END CAPS (26) into the each end of the CARRIAGE (16) as shown in FIGURE 6.
• SECURELY assemble four 3” DIA. WHEELS (20) to the sides of the CARRIAGE (16) as shown in FIGURE 6 using four 1/2 X
4-1/2” BOLTS (43), eight 1/2” WASHERS (32), and four 1/2” LOW HEIGHT LOCK NUTS (34).
• Attach one 4 X 14” NON SKID STRIP (25) to the CARRIAGE (16) as shown in FIGURE 6.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
31
LOW HEIGHT 34
29
21
32
3/8 X 2” 36
14
1/2 X 2-3/4” 40
BRACKETS
31
16
29
21
36 3/8 X 2”
FIGURE 7
STEP 7:
• SECURELY assemble two 2” DIA. WHEELS (21) to the BRACKETS on the left side of the CARRIAGE (16) as shown in
FIGURE 7 using two 3/8 X 2” BOLTS (36), four 3/8” WASHERS (29), and two 3/8” LOCK NUTS (31).
• Assemble the two ADJ. WHEEL BRACKETS (14) to the right side of the CARRIAGE (16) as shown in FIGURE 7 using two 1/2
X 2-3/4” BOLTS (40), two 1/2” WASHERS (32), and two 1/2” LOW HEIGHT LOCK NUTS (34). (NOTE: TIGHTEN BRACK-
ETS SECURELY TO THE CARRIAGE, THEN BACK NUT OFF 1/2 TURN TO ALLOW FOR ADJUSTMENT IN A
LATTER STEP).
• SECURELY assemble two 2” DIA. WHEELS (21) to the ADJ. WHEEL BRACKETS (14) on the right side of the CARRIAGE
(16) as shown in FIGURE 7 using two 3/8 X 2” BOLTS (36), four 3/8” WASHERS (29), and two 3/8” LOCK NUTS (31).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43 1/2 X 4-1/2”
16
9
SAFTEY
STOP
8
FIGURE 8
STEP 8:
• Remove the two temporary 1/2 X 4-1/2” BOLTS (43) from STEP 5.
• Swing the LEFT (8) and RIGHT (9) RAILS out enough to insert the CARRIAGE ASSEMBLY (16) in between them. Allow the
CARRIAGE (16) to rest on the SAFETY STOPS underneath the RAILS. See FIGURE 8.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43 1/2 X 4-1/2”
6
14
32
16
32
33
21
9
14
8
REVERSE VIEW
FOR ASSEMBLY
6
FIGURE 9
STEP 9:
• SECURELY reassemble the LEFT (8) and RIGHT (9) RAILS to the REAR UPRIGHT (6) as shown in FIGURE 9 using the two 1/2
X 4-1/2” BOLTS (43), four 1/2” WASHERS (32), and two 1/2” LOCK NUTS (33). (!!! IMPORTANT !!! BEFORE TIGHTENING
MOVE THE RAILS IN AS FAR AS POSSIBLE)
• SECURELY tighten the two 3/8 X 4-1/2” BOLTS (38) holding the SEAT PAD (18) from STEP 5. (!!! IMPORTANT !!! BEFORE
TIGHTENING MOVE THE RAILS INAS FARAS POSSIBLE)
• To adjust the side to side movement of the CARRIAGE (16), start by sliding the CARRIAGE (16) as far to the left as possible
inside the RAILS (8 & 9). Adjust the ADJ. WHEEL BRACKETS (14) out until the 2” DIA. WHEELS (21) contact the RIGHT
RAIL (9). SECURELY tighten bolt connection. See FIGURE 9 and REVERSE CARRIAGE VIEW.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
41 1/2 X 3-1/4”
33
13
32
43 1/2 X 4-1/2”
32
33
16
FIGURE 10
STEP 10:
• SECURELY assemble both WEIGHT SUPPORT (13) and PAD SUPPORTS 93)to the CARRIAGE (16) as shown in FIGURE 10 using
two 1/2 X 4-1/2” BOLTS (43), two 1/2 X 3-1/4” BOLTS (41), eight 1/2” WASHERS (32), and four 1/2” LOCK NUTS (33).
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
14
Download from Www.Somanuals.com. All Manuals Search And Download.
30
26
29
3/8 X 3” 37
17
SURFACETO BE EVEN
3
33
32
41 1/2 X 3-1/4”
FIGURE 11
STEP 11:
• SECURELY assemble the two PAD SUPPORTS (3) to the CARRIAGE (16) as shown in FIGURE 11 using two 1/2 X 3-1/4”
BOLTS (41), four 1/2” WASHERS (32), and two 1/2” LOCK NUTS (33).
• SECURELY assemble two SHOULDER PADS (17) to the PAD SUPPORTS (3) on the CARRIAGE (16) as shown in FIGURE 11 using
four 3/8 X 3” BOLTS (37), four 3/8” LOCK WASHERS (30), and four 3/8”WASHERS (29). (NOTE: THATHOLES IN PADS ARE
OFF-SETTOONESIDE)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
10
47
24
FIGURE 12
STEP 12:
• Attach two 1-1/4” SQ. RUBBER BUMPERS (24) to the ends of the ANGLES of the FOOT PLATE (10) as shown in FIGURE 12.
• SECURELY assemble one 1/2” DIA. SPRING PIN (47) to the SPRING PIN HOUSING on the FOOT PLATE (10) as shown in
FIGURE 12. (!!! IMPORTANT !!! TIGHTEN THE NUT OF THE SPRING PIN SECURELY)
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
16
Download from Www.Somanuals.com. All Manuals Search And Download.
32
10
34 LOW HEIGHT
39 1/2 X 1-1/4”
16
FIGURE 13
STEP 13:
• Assemble the FOOT PLATE (10) to the CARRIAGE (16) as shown in FIGURE 13, using two 1/2 X 1-1/4” BOLTS (39), two 1/2”
WASHERS (32), and two 1/2” LOW HEIGHT LOCK NUTS (34). (TIGHTEN THE CONNECTION COMPLETELY, THEN
BACK THE NUTS OFF 1/4 TURN)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BUSHING
45
8
9
7
SURE-LOC
BUSHING
22
FIGURE 14
STEP 14:
• To assemble the CARRIAGE STOP BAR (7) to the side of the LEFT RAIL (8), start by inserting the top of the BAR (7) into the
BUSHING at the top of the RAIL as far as possible, then lower the BAR (7) into the SURE-LOC BUSHING at the bottom of the
RAIL. (MAKE SURE THE STOP PEGS ARE VERTICAL), then insert one 1-1/4” ROLL PIN (45) into the hole at the top of
the BAR (7). (DO NOT LET THE ROLL PIN PROTRUDE BENEATH THE BAR) Repeat this step on the RIGHT RAIL (9).
• Slide two 1-1/4 X 5” GRIPS (22) over the HANDLES on the CARRIAGE STOP BARS (7) as shown in FIGURE 14.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
15
19
29
30
3/8 X 1” 35
FIGURE 15
STEP 15:
• SECURELY assemble the PAD STOP (15) to the BACK PAD (19) as shown in FIGURE 15 using two 3/8 X 1” BOLTS (35), two
3/8” LOCK WASHERS (30), and two 3/8” WASHERS (29).
MAKE SUREALLCONNECTIONSARE SECURELY TIGHTENED.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CARRIAGE
STOPS
16
7
BAR
HANDLES
11
SURE-LOC
BUSHING
35°,40°,45°
FIGURE 16
STEP 16:
• The PLATFORM (11) can adjust into three positions: 35, 40, and 45 degrees
• The HIP SLED was designed with the SURE-LOC SYSTEM for ultimate safety. To activate the CARRIAGE STOP BARS (7)from
either the LEG PRESS or HACK SQUAT position, begin by moving the CARRIAGE (16) up. Grasp the (HANDLES or BAR) on
the CARRIAGE STOP BARS (7) and (push or pull) up and rotate them out. Now the stops are out of the way to perform the
exercise.
• To stop the CARRIAGE (16) on one of the three carriage stops simply rotate the CARRIAGE STOP BARS (7) back up and allow
them to drop down into the SURE-LOC SYSTEM.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
20
Download from Www.Somanuals.com. All Manuals Search And Download.
19
7
10
11
PLATFORM
HANLDE
FIGURE 17
STEP 17:
• To perform LEG PRESSES, center the BACK PAD (19) down on top of the PLATFORM (11) and lock the PAD STOP (15) on the
back of the BACK PAD (19) behind the PLATFORM HANDLE then rotate the FOOT PLATE (10) on the CARRIAGE (16) up
until the SPRING PIN engages the hole
• To perform CALF RAISES, move the CARRIAGE (16) to the top carriage stop of the CARRIAGE STOP BAR (7). Place feet on
the HORIZONTALTUBE of the CARRIAGE (16). (WHERE THE NON-SKID STRIP IS LOCATED) (DO NOT ROTATE
THE CARRIAGE STOP BARS DOWN FOR THIS EXERCISE)
• To perform HACK SQUATS, make sure that the FOOT PLATE (10) of the CARRIAGE (16) is down. Position the BACK PAD
(19) between the SHOULDER PADS of the CARRIAGE (16). (MAKE SURE THAT THE PAD STOP IS RESTINGABOVE
THE CROSS TUBE ON THE CARRIAGE)
THIS CONCLUDES THE ASSEMBLY OF THE 835 HIP SLED SYSTEM.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Please note:
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your ParaBody customer service representative
at (800) 328-9714.
* Inspect equipment daily. Tighten all loose connections are replace worn parts immediately.
Failure to do so may result in serious injury
* PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT
YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION.
REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND
MAIL BACK.
MODEL #________________________
SERIAL #_________________________
DATE OF PURCHASE: _____________
DEALERS NAME: _________________
DEALERS PHONE #_______________
SERIALNUMBER LOCATIONS
Thank you for purchasing the ParaBody 835 Hip Sled System.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY.
1. LIMITED WARRANTY ON FRAMEAND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired
or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
2. LIMITED WARRANTY ON PARTS. If the following parts are defective in material or workmanship, ParaBody will supply replacement parts:
all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad
shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger, spring
and knob. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in material or workmanship,
ParaBody will repair or replace them, at its option. Terms: Three (3) years.
4. CONDITIONS AND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized
ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of
ParaBody will void this Limited Warranty.
5. REPLACEMENT AND REPAIR EXPENSES. ParaBody will provide only replacement parts or repair under this warranty. The Owner is
responsible for all other costs. Such costs may include, but are not limited to: a. labor charges for service, removal, repair or reinstallation
of the ParaBody product or any component part; b. shipping, delivery, handling and administrative charges for returning parts to ParaBody;
and c. all necessary or incidental costs related to installation of the replacement parts.
6. SHIPPING. If shipping by the Owners is deemed necessary (in sole discretion of ParaBody), parts should be shipped in their original carton
or equivalent packaging, fully insured with shipping charges prepaid. ParaBody will not assume any responsibility for any loss or damage
incurred in shipping.
7. CLAIM PROCEDURES. If service on your ParaBody product is required during the warranty period, please contact our Customer Service
Department at 1-800-328-9714 for instructions regarding returning or replacing parts. Please have available the following information: (i) the
dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly
drawing included with your assembly instruction); (iv) a description of the nature of the problem.
8. OWNER’S RIGHT. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary depending on local law.
9. LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law, shall have no greater
duration than the warranty period set forth above. There are no warranties which extend beyond the description in this Limited Warranty.
Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you.
10. DISCLAIMER. No other express warranty has been made or will be made on behalf of ParaBody with respect to any ParaBody product or
the operation, repair or replacement of any ParaBody product. ParaBody shall not be responsible for injury, loss of use of the ParaBody
product, inconvenience, loss or damage to personal property, whether direct or indirect, and incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
NOTES:
23
Download from Www.Somanuals.com. All Manuals Search And Download.
LIFE FITNESS
14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A.
Tel: 763.323.4500 Fax: 763.323.4797
800.328.9714 (Toll-free within the U.S. and Canada)
INTERNATIONALOFFICES
Life FitnessAtlantic BV
Life Fitness (UK) Ltd.
QueenAdelaide
Ely, Cambs CB7 4UB
United Kingdom
Phone CSS: (01353) 665507
Fax CSS: (01353) 666719
Atlantic Headquarters
Bijdorpplein 25-31
2992 LB Barendrecht
The Netherlands
Phone: (180) 646 666
Fax: (180) 646 703
Life Fitness EUROPE GmbH
Siemensstrasse 3
Life Fitness Benelux N.V.
Bijdorpplein 25-31
85716 Unterschleissheim
Germany
2992 LB Barendrecht
The Netherlands
Phone: (089) 31 77 51-0
Fax: (089) 31 77 51 99
Phone: 31 (180) 64 66 69
Fax: 31 (180) 64 66 99
Life Fitness Japan
8/F, Nippon Brunswick Building
5-27-7 Sendagaya
Shibuya-Ku, Tokyo 151-0051
Japan
Phone: 81 (3) 3359-4309
Fax: 81 (3) 3359-4307
Life Fitness Italia S.R.L.
Via Elvas 92
39042 Bressanone
Italy
Phone: 39 (472) 835-470
Fax: 39 (472) 833-150
Life Fitness Do Brazil
Al. Rio Negro, 433-Predio 2-Sala 2
3º andar (Confab)
Aplhaville-Barueri-Sao Paulo
CEP: 06454-904
Life FitnessAsia Pacific Limited
Room 2610, Miramar Tower
132 Nathan Road, Tsimshatsui
Kowloon, Hong Kong
Phone: (852) 2891-6677
Fax: (852) 2575-6001
Brazil
Phone: 55 (11)7295-2217
Fax: 55 (11) 7295-2218
24
Download from Www.Somanuals.com. All Manuals Search And Download.
|