832102 LEG PRESS
ASSEMBLY INSTRUCTIONS
Part # 6763901
Rev.A
1
Version: 832102
Revision: 06/27/01
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY PART #
DESCRIPTION
BASE FRAME
SEATFRAME
REAR TUBE
QTY
1
KEY PART #
DESCRIPTION
3/8” LOCK WASHER
3/8” LOCK NUT
QTY
1
2
3
4
5
6
7
8
9
6574503
6573603
6655701
6575403
6573903
6476403
6575102
6597402
6574001
18 3102601
19 3102802
4
2
1
2
2
2
2
2
1
2
2
2
8
4
4
1
1
1
20 3102807 3/8” LOW HEIGHT LOCK NUT
21 3102801 1/2” LOCK NUT
22 3102804 1/2” LOW HEIGHT LOCK NUT
FOOT PLATE
1
LEVER TUBE
HANDLE
2
1
23 3102941
24 3102922
25 3102904
26 3102935
27 3102918
28 3202107
29 6122703
30 6020601
31 3104901
32 3106803
33 6412001
3/8 X 1-1/2” BOLT
3/8 X 2-3/4” BOLT
3/8 X 3” BOLT
ADJUSTMENT TUBE
SEATPAD
1
2
3/4 X 8-1/4” SHAFT
1 X 8” GRIP
2
3/8 X 4-1/2” BOLT
1/2 X 3-1/4” BOLT
1/2 X 6-1/2” BOLT
3/8 ID X 3/8” SPACER
1/2” FLANGE BEARING
3/4” FLANGE BEARING
5/16” SET SCREW
3/8” SPRING PIN
10 3103102
11 3116201
2
3-1/2” PULLEY
1
12 6177001 2-1/2 X 5-1/2” NON-SKID STRIP
8
13 6405201
14 6416601
15 6467001
16 6500601
17 3102501
2” SQ. END CAP
PARAGLIDE (QTY. 8)
2” SQ. COVER CAP
2” WHEEL
14
1
2
2
3/8” FLATWASHER
8
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1
13
19
3
17
3/8 X 3” 25
15
FIGURE 1
STEP 1:
• Attach two 2” SQ. COVER CAPS (15) onto the ends of the REAR TUBE (3) as shown in FIGURE 1.
• Insert four 2” SQ. ENDCAPS (13) into the ends of the BASE FRAME (1) as shown in FIGURE 1.
• SECURELY assemble the REAR TUBE (3) to the BASE FRAME (1) using two 3/8 X 3” BOLTS (25), four 3/8” FLAT WASHERS
(17), and two 3/8” LOCK NUTS (19). See FIGURE 1.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
4
Download from Www.Somanuals.com. All Manuals Search And Download.
14
2
33
13
FIGURE 2
STEP 2:
• Insert two 2” SQ. ENDCAPS (13) into the ends of the SEAT FRAME (2) as shown in FIGURE 2.
• SECURELY assemble one 3/8” SPRING PIN (33) to the spring pin barrel on the SEAT FRAME (2) as shown in FIGURE 2.
• Attach four PARAGLIDE STRIPS (14) to the inside of the SEAT FRAME (2) using the following steps:
•
•
Thoroughly clean all surfaces where the PARAGLIDE STRIPS (14) are to be attached.
Remove the PARAGLIDE STRIPS (14) from the paper backing and firmly apply them to all shown surfaces.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3/8” LOW HEIGHT 20
11
29
7
17
16
3/8 X 4-1/2” 26
14
FIGURE 3
STEP 3:
• SECURELY assemble one 3-1/2” PULLEY (11), two 2” WHEELS (16), two 3/8” FLAT WASHERS (17), and two 3/8 ID X 3/8”
SPACERS (29) to the ADJUSTMENT TUBE (7) using one 3/8 X 4-1/2” BOLT (26) and one LOW HEIGHT LOCK NUT (20)
as shown in FIGURE 3.
• Attach four PARAGLIDE STRIPS (14) to the outside of the ADJUSTMENT TUBE (7) using the following steps:
•
•
Thoroughly clean all surfaces where the PARAGLIDE STRIPS (14) are to be attached.
Remove the PARAGLIDE STRIPS (14) from the paper backing and firmly apply them to all shown surfaces.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
SPRING PIN
2
FIGURE 4
STEP 4:
• CAREFULLEY slide the ADJUSTMENT TUBE (7) over into the SEAT FRAME (2) and engage the SPRING PIN into one of
the adjustment holes. See FIGURE 4.
STEP 5:
• Insert two 3/4” FLANGE BEARINGS (31)
into each of the two LEVER TUBES (5) as
shown in FIGURE 5.
31
31
5
5
FIGURE 5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5/16” SET SCREW 32
5
9
17
1
FIGURE 6
STEP 6:
• Insert four 2” SQ. END CAPS (13) into the ends of two LEVER TUBES (5) as shown in FIGURE 6.
• SECURELY assemble the LEVER TUBES (5) to the BASE FRAME (1) using two 3/4” SHAFTS (9) and SECURE in place
using four 5/16” SET SCREWS (32). See FIGURE 6.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4
30
13
5
1
FIGURE 7
STEP 7:
• Insert four 2” SQ. END CAPS (13) into the ends of FOOT PLATE (4) as shown in FIGURE 7.
• Insert eight 1/2” FLANGE BEARING (30) into the LEVER TUBES (5) as shown in FIGURE 7.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1/2” LOW HEIGHT 22
4
12
28 1/2 X 6-1/2”
5
FIGURE 8
STEP 8:
• SECURELY assemble the FOOT PLATE (4) to the LEVER TUBES (5) using two 1/2 X 6-1/2” BOLTS (28) and two 1/2” LOW
HEIGHT LOCK NUTS (22) as shown in FIGURE 8.
• CAREFULLY attach eight NON-SKID STRIPS (12) to the FOOT PLATE (4) as shown in FIGURE 8.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5
21
2
27 1/2 X 3-1/4”
FIGURE 9
STEP 9:
• SECURELY assemble the SEAT FRAME (2) to the LEVER TUBES (5) using two 1/2 X 3-1/4” BOLTS (27) and two 1/2” LOCK
NUTS (21) as shown in FIGURE 9.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
8
6
2
17
18
3/8 X 1-1/2” 23
FIGURE 10
STEP 10:
• SECURELY assemble the SEAT PAD (8) to the HANDLE (6) and the SEAT FRAME (2) using two 3/8 X 1-1/2” BOLTS (23),
two 3/8” LOCK WASHERS (18), and two 3/8” FLAT WASHERS (17). See FIGURE 10.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
12
Download from Www.Somanuals.com. All Manuals Search And Download.
10
8
2
18
24 3/8 X 2-3/4”
FIGURE 11
STEP 11:
• SECURELY assemble the SEAT PAD (8) to the SEAT FRAME (2) using two 3/8 X 2-3/4” BOLTS (24) and two 3/8” LOCK
WASHERS (18) as shown in FIGURE 11.
• Slide two 1 X 8” GRIPS (10) over each HANDLE (6) as shown in FIGURE 11.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 12
STEP 12:
•
•
To adjust the SEAT, sit in the LEG PRESS, gently press against the FOOT PLATE and pull back on the SPRING PIN.
Refer to the LEG PRESS ADAPTOR assembly instructions to attach the 832102 LEG PRESS to the home gym.
Thank you for purchasing the Parabody 832102 LEG PRESS. If unsure of proper use of equipment, call
your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|