441101 440 LEG PRESS ADAPTER KIT
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
ASSEMBLY INSTRUCTIONS
Part # 7039101
REV. B
1
Revision: 07/19/01
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY PART #
DESCRIPTION
FRONT LEG
QTY
KEY PART #
DESCRIPTION
3/8” WASHER
QTY
1
2
3
4
5
6
7
8
9
6686608
6693902
6694002
6694208
3116201
6405201
6467001
3108102
6140701
1
1
1
1
2
1
2
1
2
10 3102501
11 3102802
12 3102801
13 3102924
14 3102904
15 3102918
16 7032303
17 6694401
4
5
2
3
2
2
1
1
PULLEY BRACKET
CABLE SWIVEL
BASE CONNECTION
3-1/2” PULLEY
3/8” LOCKNUT
1/2” LOCKNUT
3/8 X 1-3/4” BOLT
3/8 X 3” BOLT
2” SQ. END CAP
COVER CAP
1/2 X 3-1/4” BOLT
110-3/4” CABLE ASSY
82-1/2” CABLE ASSY
QUICK DISCONNECT LINK
GLIDE 1 X 1”
NOTE: The LEG PRESS ATTACHTMENT (100101) must be assembled before connecting it to the
PARABODY 440 HOME GYM
STEP 1
• Slide two COVER CAPS (7) over the FRONT LEG (1)
as shown in FIGURE 1
7
1
FIGURE 1
STEP 2
• Slide one 2” SQ. END CAP (6) into the BASE CONNECTION (4)
as shown in FIGURE 2.
4
6
FIGURE 2
9
STEP 3
• Attach two 1 X 1” GLIDES (9) to the top of PULLEY BRACKET
(2) as shown in FIGURE 3.
2
FIGURE 3
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1/2 X 3-1/4” 15
1
4
12
FIGURE 4
STEP 4
•
Securely fasten the FRONT LEG (1) and the BASE CONNECTION (4) to the 440 HOME GYM using two 1/2 X 3-1/4” BOLTS
(15) and two 1/2” LOCKNUTS (12). See FIGURE 4.
FIGURE 5
STEP 5
• Remove one existing 3-1/2” PULLEY and two SPACERS
from theADJUSTMENT TUBE on the 100 LEG PRESS
OPTION by unfastening the 3/8 X 4-1/2” BOLT holding
the pulley on. See FIGURE 5. (Note: Save 3-1/2”
PULLEY, it will be used in later steps.)
3-1/2” PULLEY
SPACER
2” WHEEL
3/8 X 4-1/2”
BOLT
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6
• Attach CABLE SWIVEL (3) to the
ADJUSTMENT TUBE on the 100 LEG
PRESS using the existing previously removed
3/8 X 4-1/2” BOLTS, WASHERS, 2”
WHEELS AND NUT. (Note: Securely
tighten, then back off 1/4 turn to allow the
CABLE SWIVEL & WHEELS to rotate
freely.) See FIGURE 6.
2” WHEEL
NUT
3
2” WHEEL
3/8 X 4-1/2” BOLT
FIGURE 6
10
3/8 X 3” 14
11
10
1
FIGURE 7
STEP 7
•
Securely fasten the 100 LEG PRESS to the FRONT LEG (1) using two 3/8 X 3” BOLTS (14), four 3/8” WASHERS (10), and two
3/8” LOCKNUTS (11) as shown in FIGURE 7.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 8
REMOVE CABLE
STEP 8
Remove the existing LAT CABLE using the following steps:
• Disconnect LAT BAR from TOP BOOM.
• Unscrew the threaded end of CABLE from the HEAD PLATE ASSEMBLY.
• Route the LAT CABLE around the PULLEY BLOCK as shown in FIGURE 8.
• Route the LAT CABLE around the TOP BOOM as shown in FIGURE 8.
• The pulleys in TOP BOOM may need to be temporarily removed to remove CABLE.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
6
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 9
IMPORTANT: Cable must run over the top of
bolts.
2
16
STEP 9
Install the NEW 110-3/4” CABLE ASSY (16) using the following steps:
• Route the CABLE (16) through the TOP BOOM as shown in FIGURE 9. The pulleys in TOP BOOM may need to be temporarily
removed to perform this step. (Note: Make sure the CABLE is running OVER the BOLTS connecting the FRONT UPRIGHT
to the TOP BOOM. These may also have to be removed to perform this step.)
•
Route the CABLE (16) around the PULLEY BLOCK as shown in FIGURE 9.
• Route the CABLE (16) back over one pulley in the TOP BOOM, down through the PULLEY BRACKET (2) and over the second
pulley in the TOP BOOM.
FIGURE 10
•
Screw the threaded end of CABLE (16) into the HEAD PLATE
ASSEMBLY.
STEP 10
Loop CABLE (16) around one 3-1/2” PULLEY (5) in the PULLEY
•
16
11
BRACKET (2) using one 3/8 X 1-3/4” BOLT (13) and one 3/8”
LOCKNUT (11) as shown in FIGURE 10.
5
2
3/8 X 1-3/4” 13
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 11
8
3
17
IMPORTANT:
Tighten QUICK DISCONNECT LINK
SECURELY.
STEP 11
•
Attach the hook end of 82-1/2” CABLE (17) to the CABLE SWIVEL (3) with one QUICK DISCONNECT LINK (8).
IMPORTANT: Tighten the QUICK DISCONNECT LINK (8) securely.
•
Route the 82-1/2” CABLE (17) under the WEIGHT STACK as shown in FIGURE 11.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
8
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 12
FIGURE 12
• Screw the threaded end of 82-1/2” CABLE (17) to the PULLEY
BRACKET (2) as shown in FIGURE 12.
2
17
11
4
17
1
5
3/8 X 1-3/4” 13
FIGURE 13
STEP 13
• Attach one 3-1/2” PULLEY (5) to the FRONT LEG (1) and one 3-1/2” PULLEY (5) to the BASE CONNECTION (4) using two 3/
8 X 1-3/4” BOLTS (13) and two 3/8” LOCKNUTS (11). (Note: Make sure CABLE (17) is running under PULLEYS.)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2
17
16
SPRING PIN ADJUSTMENT
FIGURE 14
STEP 14
•
•
The 100 LEG PRESS is equipped with a spring pin adjustment to accommodate different sized users and allow easy entry and exit
from the machine. To use, you must slightly push against the foot plates to take tension off the pin.
To set the correct amount of tension in the cables, adjust the 100 LEG PRESS into the last adjustment hole (so the LEG PRESS is
spread apart) and remove the WEIGHT STACK PIN. Thread the 110-3/4” CABLE (16) into the HEAD PLATE ASSEMBLY until
the PULLEY BRACKET (2) is held against the TOP BOOM and the cable is slightly pulling up on the HEAD PLATE. Tighten the
jan but securely. Next, thread the 82-1/2” CABLE (17) into the PULLEY BRACKET (2) until cable is tight , then tighten the jam
nut securely.
Thank you for purchasing the Parabody 441101 LEGPRESSADAPTER KIT. If unsure of proper use of
equipment, call your local Parabody distributor or call the Parabody customer service department at (800)
328-9714.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|