360101 375 LEG PRESS ADAPTER KIT
ASSEMBLY INSTRUCTION
Part # 6837701
1
Revision: 07/06/99
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY PART #
DESCRIPTION
FRONTLEG
QTY
KEY PART #
DESCRIPTION
3/8” LOCKNUT
3/8 X 2” BOLT
QTY
1
2
3
4
5
6
7
8
6838003
6693902
6838103
3116201
6405201
6467001
6832701
3102501
1
1
1
2
1
2
1
6
9
3102802
3102933
3102910
3102937
6837801
6837901
3102502
3102801
3
3
2
2
1
1
2
2
PULLEYBRACKET
BASE CONNECTION
3-1/2”PULLEY
10
11
12
13
14
15
16
1/2 X 3” BOLT
1/2 X 4-1/2” BOLT
PRIMARYCABLE
LEGPRESSCABLE
1/2” WASHER
2” SQ. END CAP
2” SQ. COVER CAP
2” SQ. RUBBER BUMPER
3/8” WASHER
1/2” LOCK NUT
NOTE: The LEGPRESSATTACHMENT (832101) must be assembled before connecting it to the
PARABODY375 HOME GYM
STEP 1
• Slide two 2” SQ. COVER CAPS (6) over the FRONT LEG
(1) as shown in FIGURE 1.
6
1
FIGURE 1
STEP 2
•
Slide one 2” SQ. END CAP (5) into the BASE CONNECTION (3) as
shown in FIGURE 2.
3
5
7
FIGURE 2
STEP 3
• Attach one 2” SQ. RUBBER BUMPER (7) to the top of the PULLEY
BRACKET (2) as shown in FIGURE 3.
2
FIGURE 3
3
Download from Www.Somanuals.com. All Manuals Search And Download.
STACK GUARD
1/2”
NUT
BASE
1/2” WASHER
1/2 X 4” BOLT
FIGURE 4
STEP 4
•
Remove two 1/2 X 4” BOLTS, two 1/2” WASHERS, and two 1/2” LOCK NUTS from the BASE and STACK GUARD as shown in
FIGURE 4. (NOTE: Discard the 1/2 X 4” BOLT.)
1/2”
NUT
BASE
3
1
STACK GUARD
12 1/2 X 4-1/2”
FIGURE 5
STEP 5
Securely fasten the FRONT LEG (1) and the BASE CONNECTION (3) to the BASE and STACK GUARD using two 1/2 X 4-1/2”
BOLTS (12) and two previously removed 1/2” LOCKNUTS. See FIGURE 5.
•
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE CABLE
FIGURE 6
STEP 6
Remove the existing CABLE (part #68331) using the following steps:
• Disconnect LAT BAR from TOP BOOM.
• Unscrew the threaded end of CABLE from the HEAD PLATE ASSEMBLY.
• Route the CABLE around the FLOATING PULLEY as shown in FIGURE 6.
• Route the CABLE through the TOP BOOM as shown in FIGURE 6.
• The pulleys in TOP BOOM may need to be temporarily removed to remove CABLE.
• (NOTE: Discard CABLE part #68331)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 7
IMPORTANT: Cable must run
in all the pulley grooves.
2
13
STEP 7
Install the NEW PRIMARYCABLE (13) using the following steps:
• Route the CABLE (13) through the TOP BOOM as shown in FIGURE 7. The pulleys in TOP BOOM may need to be temporarily removed
to perform this step. (Note: Make sure the CABLE is running in all the pulley grooves.)
•
•
Route the CABLE (13) around the FLOATING PULLEY BRACKET as shown in FIGURE 7.
Route the CABLE (13) back over one pulley in the GUIDE ROD SUPPORT, down through the PULLEY BRACKET (2) and over the
second pulley in the GUIDE ROD SUPPORT.
•
Screw the threaded end of CABLE (13) into the HEAD PLATEASSEMBLY.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 8
9
4
8
2
10 3/8 X 2”
STEP 8
•
Loop CABLE (13) around one 3-1/2” PULLEY(4) in the PULLEYBRACKET (2) and SECURELYassemble using one 3/8 X 2”
BOLT (10), and two 3/8” WASHERS (8) and one 3/8” LOCK NUT (9) as shown in FIGURE 8.
FIGURE 9
STEP 9
Remove one existing 3-1/2” PULLEY,two WASHERS,
•
two 2” WHEELS and two SPACERS from the
ADJUSTMENT TUBE on the 832 LEG PRESS OPTION
by unfastening the 3/8 X 4-1/2” BOLT holding the
pulley on. See FIGURE 9. (NOTE: The pulley will be
used in STEP 12.)
3-1/2”PULLEY
SPACER
2”WHEEL
3/8 X 4-1/2”
BOLT
7
Download from Www.Somanuals.com. All Manuals Search And Download.
14
NUT
SPACER
WASHER
DO NOT
OVERTIGHTEN!
2”WHEEL
3/8 X 4-1/2” BOLT
FIGURE 10
STEP 10
• Assemble the LEG PRESS CABLE (14) to the ADJUSTMENT TUBE on the 832 using the existing previously removed 3/8 X 4-1/2”
BOLTS, SPACERS, WASHERS, 2”WHEELSAND NUT. (Note: Do not overtighten! Tighten only until nut is completely on bolt.) See
FIGURE10.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
8
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1/2 X 3” 11
15
1
16
FIGURE 11
STEP11
•
Securely fasten the 832 LEG PRESS to the FRONTLEG (1) using two 1/2 X 3” BOLTS (11), two 1/2” WASHERS (15), and two 1/2” LOCK
NUTS (16) as shown in FIGURE 11.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
9
4
3
14
1
8
10 3/8 X 2”
FIGURE 12
STEP 12
•
Attach one 3-1/2” PULLEY (4) to the FRONT LEG (1) and one 3-1/2” PULLEY (4) to the BASE CONNECTION (3) using two 3/8 X
2” BOLTS (10), four 3/8” WASHERS (8) and two 3/8” LOCKNUTS (9). (Note: Make sure CABLE (14) is running under
PULLEYS.)
FIGURE 13
STEP 13
Screw the threaded end of LEG PRESS CABLE (14) to the
PULLEY BRACKET (2) as shown in FIGURE 13.
•
2
14
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2
14
ADJUST!
ADJUST!
13
ADJUST!
SPRING PIN ADJUSTMENT
FIGURE 14
STEP 14
• The 832 LEG PRESS is equipped with a spring pin adjustment to accommodate different sized users and allow easy entry and exit from
the machine. To use, you must slightly push against the foot plates to take tension off the pin.
•
To set the correct amount of tension in the cables, adjust the 832 LEG PRESS into the last adjustment hole (so the LEG PRESS is spread
apart) and remove the WEIGHT STACK PIN. Thread the PRIMARY CABLE (13) into the HEAD PLATE ASSEMBLY until both
PULLEY BRACKETS (2) are held against the TOP BOOM and the cable is slightly pulling up on the HEAD PLATE. Tighten the jam
but securely. Next, thread the LEG PRESS CABLE (14) into the PULLEY BRACKET (2) until cable is tight , then tighten the jam nut
securely.
•
If further adjustment is needed, lossen and adjust the pulley attached to the slotted tab on the BENCH FRAME. (NOTE: It is natural
for the LEG PRESS CABLE to slacken when seat is adjusted inward.)
Thank you for purchasing the Parabody 360101 Leg Press Adapter Kit. If unsure of proper use of equipment,
call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|