Panasonic Video Eyeware Crystal Eyes Wear User Manual

User’s Manual  
StereoGraphics Corporation  
2171 East Francisco Blvd., San Rafael, CA 94901  
phone 800-783-2660 (within USA & Canada )  
415-459-4500 (all other areas)  
fax  
415-459-3020  
e-mail  
Installation & Setup  
Each pair of CrystalEyes eyewear includes two fresh batteries, which are installed at the factory. A compatible  
stereo computer grapics or video system must be available to check the operation of the eyewear. To activate  
the eyewear, unfold the temple pieces; to turn off the eyewear, fold the templepieces. When not in use, fold  
your CrystalEyes eyewear with the temples laying flat across the back of the lenses for convenient storage.  
Always fold the eyewear when not in use to maximize the battery life.  
Installing the StereoGraphics Emitter  
StereoGraphics CrystalEyes requires the use of an infrared emitter in order to synchronize the eyewear in  
conjunction with the left and right image sequence on screen. The I/R receiver (located in the center of the  
eyewear) must be in line of sight and in range of the emitter for successful operation of CrystalEyes. Please  
consult the documentation accompanying your emitter for installation and operation details.  
In all cases except for non-stereo-ready PCs, the system or graphics card manufacturer requires specific display  
settings to enable Stereo3D mode. Please consult the manual or vendor for your specific graphics subsystem to  
determine the proper settings for Stereo3D mode. For best results in using CrystalEyes with standard  
workstation displays, set the emitter slightly behind the top edge of the monitor, as shown in Figure 1. In  
addition:  
• For EPRO, ESGI and ELR emitters, make sure the emitter is switched  
to the ON position. Depending on the emitter range needed, switch  
the emitter to either the high or low setting.  
• The ENT emitter will switch on and off automatically whenever a sync  
signal is presented by the graphics card.  
• Users of the EPC-2 must switch the emitter from BYPASS to STEREO  
MODE and set the emitter range separately.  
Figure 1. Display and Emitter  
Prescription Glasses  
If you normally wear prescription eyeglasses, place CrystalEyes over them. The eyewear will fit  
comfortably over most prescription eyeglass frames.  
Controls  
Specifications  
On/Off: Eyewear operation is switched on and off  
Optics  
by unfolding and folding the eyewear temple pieces.  
Shutters:  
liquid crystal  
32% typical  
1000:1 typical  
Less than 0.2 milliseconds  
Less than 3 milliseconds  
80 to 160 fields per second  
Automatically selected  
Bright mode: Both lenses automatically switch to  
full transparency for up to 8 minutes when shielded  
from infrared signals. Restoring the infrared signal  
returns the eyewear to full operation.  
Transmittance:  
Dynamic Range:  
Close Time:  
Open Time:  
Field Rate:  
Bright Mode:  
Infrared Sensor  
Angle of View:  
Batteries  
Two 3 V lithium/manganese dioxide  
(NEDA 5004L), including:  
90 degrees horizontal  
140 degrees vertical  
Sanyo  
Seiko  
CR2032  
CR2032  
Eveready  
Maxell  
E-CR2032  
CR2032  
Technacell CR2032  
Panasonic CR2032  
Ray-O-Vac CR2032  
Weight  
Varta  
Duracell  
CR2032  
DL2032  
3.3 oz. (93 grams)  
Saft  
LM2032  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Freezer KFN 8452 SD User Manual
Miele Washer W 5922 User Manual
Multi Tech Systems Network Card MT56DSU S User Manual
Murphy Switch Annunciators and Magnetic Switches User Manual
Nikon Digital Camera 13304 User Manual
Nikon Video Games AW110 User Manual
Niles Audio Speaker MSA 10A User Manual
Niles Audio Stereo Amplifier TVA50 User Manual
Numark Industries DJ Equipment SM 3 User Manual
Oreck Air Cleaner AIR8 Series User Manual