Operating Instructions
Digital HD Video Cassette Recorder
P
Model No. AJ-
E
Before operating this product, please read the instructions carefully and save this manual for future use.
ENGLISH
F0606T1086 -F D
Printed in Japan
VQT0X83-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Read this first! (continued)
For AJ-HD1400P
FCC Note:
CAUTION
This equipment has been tested and found to comply
with the limits for a class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s en-
closure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral tri-
angle is intended to alert the user to the pres-
ence of important operating and maintenance
(service) instructions in the literature accom-
panying the appliance.
Warning:
To assure continued FCC emission limit compliance, the
user must use only shielded interface cables when
connecting to external units. Also, any unauthorized
changes or modifications to this equipment could void
the user’s authority to operate it.
Notice (U.S.A. only):
This product has a fluorescent lamp that
contains a small amount of mercury. It also
contains lead in some components. Disposal
of these materials may be regulated in your
CAUTION:
This apparatus can be operated at a voltage in
the range of 100 – 240 V AC.
Voltages other than 120 V are not intended for
U.S.A. and Canada.
community
due
to
environmental
considerations. For disposal or recycling
information, please contact your local
authorities, or the Electronics Industries
Alliance:
CAUTION:
Operation at a voltage other than 120 V AC may
require the use of a different AC plug. Please
contact either a local or foreign Panasonic
authorized service center for assistance in
selecting an alternate AC plug.
<http://www.eiae.org.>
indicates safety information.
<For USA-California Only>
This product contains a CR Coin Cell Lithium Battery whichcontains Perchlorate Material — special handling may apply.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Read this first! (continued)
For AJ-HD1400E
Caution for AC Mains Lead
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped with 2 types of AC mains cable. One is for continental Europe, etc. and the other one is only
for U.K.
Appropriate mains cable must be used in each local area, since the other type of mains cable is not suitable.
FOR CONTINENTAL EUROPE, ETC.
FOR U.K. ONLY
Not to be used in the U.K.
If the plug supplied is not suitable for your socket out-
let, it should be cut off and appropriate one fitted.
FOR U.K. ONLY
How to replace the fuse
1. Open the fuse compartment with a screwdriver.
This appliance is supplied with a moulded three pin mains
plug for your safety and convenience.
A 13 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 13 amps and that it is ap-
proved by ASTA or BSI to BS1362.
Check for the ASTA mark
body of the fuse.
or the BSI mark
on the
2. Replace the fuse.
If the plug contains a removable fuse cover you must en-
sure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your lo-
cal Panasonic Dealer.
Fuse
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR
THE SOCKET OUTLET IN YOUR HOME THEN THE
FUSE SHOULD BE REMOVED AND THE PLUG CUT
OFF AND DISPOSED OF SAFELY. THERE IS A DAN-
GER OF SEVERE ELECTRICAL SHOCK IF THE CUT
OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.
„ DO NOT REMOVE PANEL COVERS BY UNSCREWING THEM.
To reduce the risk of electric shock, do not remove the covers. No user serviceable parts inside.
Refer servicing to qualified service personnel.
indicates safety information.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Reference signals....................................16
Example of connections
Joystick and
Pause/Recording
Recording from a variable frame rate
Recording the HD SDI output signal
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This unit is a multi-format VTR capable of recording and
playing back HD signals (1080i/59.94 Hz, 1080i/50 Hz,
720P/59.94 Hz, 720P/50 Hz) in DVCPRO HD-LP format
using a small cassette tape 1/4 inch wide, HD (DVCPRO
HD/DVCPRO HD-LP*) and SD (DVCPRO50/DVCPRO)
recorded in DVCPRO format as well as conventional
consumer DV/DVCAM tapes.
A down-converter as a standard feature verifies all tapes
using analog composite signals and SD SDI output.
Similarly, each of the following output signals can be
obtained.
z 720/25p over 60p sources can be converted to 1080/25
PsF or 576i format output signals.
z 720/50p over 60p sources can be converted to 720/50p,
1080/50i or 576i format output signals.
The compact size and light weight of the unit enable it to be
carried around and mounted in a standard rack with ease.
You can perform the unit’s settings interactively with the on-
screen menus displayed on the TV monitor.
* DVCPRO HD-LP has the same format as the DVCPRO HD EX
described in the operation manual of our camera recorder.
Features
Compact size and light weight
Frame rate conversion
The unit has a width of 214 mm (8-7/16 inches), a height
of 132 mm (5-1/4 inches), and a depth of 442 mm (17-3/
8 inches) (Protruding portion is not included), and
weighs only 8.5 kg (18.74 lb).
When playing back a tape recorded at a frame rate of 24
fps using a variable frame rate camera, the tape’s
signals can be converted to the 1080/24 PsF format and
output by selecting a menu item setting.
Grips are also attached for easy carry.
When playing back a tape recorded at a frame rate of 25
fps, the tape’s signals can be converted to the 1080/25
PsF or 576i format and output. When playing back a
tape recorded at a frame rate of 50 fps, the tape signals
can be converted to the 1080/50i or 576i format and
output.
Efficient installation in a rack
The unit’s width is one-half of 19 inches and its height is
3U: this translates into greater saving of installation
space in a standard rack compared to conventional
models.
<Notes>
z Use tapes that are shot with a variable frame rate
camera.
z Do not use dubbed or edited tapes. The tape control
information may be lost, making it impossible to
convert the signals for playback.
DVCPRO HD cassette tapes used
The unit uses 1/4-inch wide cassette tapes.
<Note>
When recording HD signals, use DVCPRO HD
cassettes.
DVCPRO-compatible playback
In addition to DVCPRO HD-LP playback, the unit can
play back tapes recorded using the existing DVCPRO
HD, DVCPRO50 and DVCPRO formats.
It can also play back consumer DV tapes (SP) and
DVCAM tapes.
High image quality
The unit achieves a high image quality by recording
4:2:2 HD component signals with a recording rate (=100
Mbps) which is four times as high as that for existing
DVCPRO formats.
SD down-converter
1080i or 720p, NTSC or PAL selectable
By switching the settings provided for the video signal
input (1080i/59.94 Hz or 720p/59.94 Hz) on the setup
menu, the unit can record and playback each signal and
also playback NTSC SD material.
The unit comes with a built-in SD down-converter as a
standard feature to enable the output of SD SDI signals
and analog composite signals at the same time as HD
SDI output signals and for monitoring the signals on an
SD monitor.
The unit also supports the PAL mode. Playback of
1080i/50 Hz, record and playback of 720P/50 Hz or
playback of PAL SD materials is enabled by switching
the setting on the system menu.
Up-convert function
When an SD format tape is played back, it is possible to
output the signals in the HD SDI output and HD analog
component signals while at the same time outputting
them in SD format, since this unit includes the HD
converter as a standard feature.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Features (continued)
Cross-convert function
PF (Programmable Function) button
The unit comes with a built-in cross-converter to enable
1080i/59.94 Hz format signals to be converted into
720p/59.94 Hz format signals or, conversely, to enable
720p/59.94 Hz format signals to be converted into
1080i/59.94 Hz format signals.
The unit is equipped with three PF buttons. Selecting
the three most frequently used setup menus, the menu
settings can be changed with the buttons on the front
panel.
Cross-convert with 1080i/50 Hz and 720p/50 Hz is also
possible.
UMID information recording and playback
This unit supports the recording/playback of UMID
(Unique Material Identifier) information in the SMPTE
330M standard. UMID information can be confirmed
with the diagnostic menu.
HD analog component output
This feature enables HD signals to be monitored with
ease.
VTRs that do not support the recording/playback of
UMID information will not playback UMID information
correctly. In addition, when VTRs that do not support
recording/playback of UMID information are connected
to this unit, UMID information will not be recorded
correctly.
Gamma correction of cinema for film
This feature corrects the image from a variable frame
rate camera in cinema gamma mode for film to an image
with film quality.
AC/DC operation
The unit supports AC supply voltages ranging from
100V to 240V and DC12V power supply as well.
VANC data recording/playback
VANC data packets that added to the Y stream of HD
SDI can be recorded with the video signal. In addition,
VANC data packets can be played back with the Y
stream of HD SDI. This unit is capable of input and
output through the IEEE1394 standard interface.
Editing function
Using the 9-pin serial remote (RS-422A), assembly or
insertion is allowed.
(Only with 1080i/59.94 Hz, 720P/59.94 Hz, 1080i/50 Hz,
and 720P/50 Hz)
AUTO REC Feature
This unit can be connected to our camera recorder
using HD SDI signals. It is possible to remotely turn ON/
OFF the recording feature of this unit by using
overlapped commands.
Encoder remote controller function
Using the external encoder remote controller, each
setting for the video output signal can be adjusted.
Follow-on recording function
Using the REC button and PAUSE button together
activates the auto back function, enabling the next
image to follow on from the last image with no
disruptions in the continuity.
On-screen menu settings
Highly detailed and individualized function settings can
be performed on-screen.
Time code
The unit is equipped with a built-in time code generator/
time code reader (TCG/TCR). Since time code signals
can also be input from an external device, regeneration
to an external time code is possible.
Since the backup function using a backup battery is
incorporated in the TCG (time code generator), time
codes during free-run operations are retained even if the
power of the unit is turned off.
Joystick and variable speed playback
The unit is equipped with a joystick (stick controller) for
use of the search function during variable speed
playback.
In addition, the joystick allows convenient setting of the
onscreen menu/time code generator.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Features (continued)
Multi-functional interfaces
z Serial digital input/output
The unit’s HD component serial I/O interface enables
interfacing with HD component video signals and 8-
channel digital audio signals using a single BNC
connector. (SMPTE 292M/296M/299M)
The unit is also equipped with an SD downconverter as
a standard feature so that SD component serial signals
can be output as well.
(SMPTE 259M-C, 272M-A, ITU-R BT.656-4)
z Analog video output
Since the unit’s down-converter comes as a standard
feature, the analog composite signals can be monitored
on an SD monitor.
z 9-pin remote
The unit’s 9-pin remote control connector enables it to
be operated with an external remote controller.
z IEEE1394 digital input/output
Set to this position when controlling this unit with the AV/
C command of the 9-pin REMOTE, REMOTE of HD
SDI, IEEE1394.
<Playback formats and output formats>
Playback format
DVCPRO HD-LP,
DVCPRO HD
DVCPRO50
DVCPRO
Output format
DVCPRO HD,
DVCPRO50, DV
DVCPRO50, DV
DVCPRO, DV
DV
DV, DVCAM
In case of EE and REC modes:
z Select a value other than “1394” with the
INPUT SELECT button on the front
panel.
DVCPRO HD
<Note>
When any of the settings below is established, no
signals will be output from the IEEE1394 digital
interface.
z When “60/24” is selected as the menu item No.030
HD FREQUENCY setting
z When “23/24,” “25 (HD),” “25 (SD),” “50 (HD),” or “50
(SD)” is selected in menu item No. 025 SYSTEM
FREQ.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
MONITOR SEL button
Front panel (1)
This button is used to select the audio signals which are
to be output to the AUDIO MON L and R connectors.
Each time the button is pressed, the audio signals to be
output to the AUDIO MON L or R connector are
changed in the following sequence.
[CH1]
[CH2]
[CH3]
[CH4]
[CH1]
[CH1]
[CH2]
[CH2]
[CH3+CH4]
[CH3]
[CH3]
[CH4]
[CH4]
L :
R :
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
HD
[CUE]
[CUE]
[CH1+CH2]
[CH1+CH2]
ꢀ
ꢀ
[CH3+CH4]
Which signal is currently selected is displayed by the
lighting of the L or R lamp on the level meter display.
Select [CH5-8] on the menu No. 783 AUDIO CH SEL to
monitor CH5 to CH8.
REC
PB
CH1
CH2
CH1
CH2
REC/PB
CH1/5
CH2/6
CH3/7
CH4/8
PB
Headphone jack and volume control
POWER switch
EJECT button
When stereo headphones are connected to the headset
jack, you can monitor the audio signal through the
headphones during recording and playback.
The headphone volume for output and monitoring output
can be adjusted with the volume control knob. Whether
the monitoring volume is linked to the volume control
knob or not can be selected in menu No. 712 MONI
OUT. In independent operation, the monitor output is
fixed regardless of the position of the volume control
knob.
When this button is pressed, the tape is unloaded and
the cassette is ejected automatically a few seconds
later. When CTL display has been selected for the
counter display, the display is reset.
To enable or disable the EJECT button operation during
recording, use menu No. 115 EJECT SW INH.
Also, the output volume of the headphones is always
linked to the volume control knob.
CONTROL switch
This is selected to control the unit from an external
source using the REMOTE connector.
REMOTE: Set to this position when controlling the unit
with the AV/C command or the commands
overlapped on the HD SDI of the 9-pin
REMOTE, via IEEE1394.
LOCAL : Set to this position to control the unit using
the controls on the unit’s operation panel.
REC INHIBIT switch
This switch is used to enable or disable recording on the
cassette tape.
ON: Recording on the cassette tape is disabled
(inhibited). In this state, the REC INH lamp lights
on the display panel.
OFF: Recording on the cassette tape is enabled so
long as the accidental erasure prevention
mechanism on the cassette tape is set to enable
recording.
METER (FULL/FINE) selector button
This button is used to select the scale display for the
audio level meter.
FULL mode:
The standard scale (– to 0 dB) is selected.
FINE mode:
The scale in 0.5 dB increments is selected. The
position indicates the standard level of –20 dB
(For AJ-HD1400P) or –18 dB (For AJ-HD1400E).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions (continued)
RESET/PF2 button
When this button is pressed in the CTL mode, the
counter display is reset to [00:00:00:00].
Front panel (2)
When it is pressed in the TC/UB mode while holding
down the TC PRESET button
, the generator is reset.
TC PRESET/PF3 button
HD
This button is used to set the TC or UB values.
SEARCH
button
MENU/DIAG button
When the connector that is selected in menu No. 005
SUPER is used, When this button is pressed, the setup
menus are displayed on the TV monitor, and the setup
menu numbers are displayed on the unit’s display panel.
When it is pressed again, the setup menu settings are
exited, and the original status is restored.
REC
PB
CH1
CH2
CH1
CH2
REC/PB
CH1/5
CH2/6
CH3/7
CH4/8
PB
When the button is pressed while holding down the PF
button
, the VTR information is displayed. When it is
INPUT SELECT buttons
pressed again, the original display is restored. The VTR
information consists of the WARNING, HOURS METER,
UMID INFO and DIF STATUS 1, 2 information.
The SEARCH button
between these kinds of information.
These buttons are used to switch the video and audio
input signals. They can also be used to switch the video
input signals to the internal reference signal selected as
the menu item No.601 VIDEO INT SG setting.
is used to switch the displays
Descriptions of the warnings are displayed on the
WARNING screen. The deck’s serial number, poweron
time, drum rotation time, tape travel time, number of
loading times, number of power on/off times, etc. are
displayed on the HOURS METER screen. The UMID
(Unique Material Identifier) information is displayed on
the UMID INFO screen. The IEEE1394 digital interface
information is displayed on the DIF STATUS 1, 2 screen.
VIDEO:
Each time the VIDEO button is pressed, the input
video signal selection is switched in the order of
[HD SDI] > [1394] > [SG].
When SG has been selected, the signal is switched to
the internal reference signal selected as the menu item
No.601 VIDEO INT SG setting.
AUDIO:
TCG switch
Each time the AUDIO button is pressed, the input
audio signal selection is switched in the order of
[HD SDI] > [SG] > [ANALOG].
REGEN: The internal time code generator is
synchronized with the time code which the time
code reader has read from the tape.
The signal that is to be used for regeneration is
selected using menu No. 505 TCG REGEN.
PRESET: The time code generator can be preset (see
page 55) on the operation panel or by remote
control.
<Notes>
z It is possible to inhibit the input switch operations
(video and audio) of the INPUT SELECT buttons
using menu item No.190 V IN SEL INH and item
No.191 A IN SEL INH.
z The audio input signal cannot be switched to [1394]
independently. The audio signal can be switched to
[1394] only when the video signal is switched to
[1394] by interlocking.
EXT:
The external time code which is input from the
time code input connector or video signal SLTC,
SVITC or IEEE1394 digital input signal is used.
Which of the two is to be set is selected using
menu No. 507 EXT TC SEL.
Since the audio input signal at this time is fixed to
[1394], it cannot be switched to another input signal.
<Note>
PF button
When this button is pressed, buttons
function as the PF1, PF2 and PF3 buttons, respectively.
When it is pressed again before another button is
pressed, these modes are canceled.
When selecting “1394” with the INPUT VIDEO switch on
the front panel, the time code input to IEEE1394 digital
input/output connector is used.
-
to
SUPER switch
When this button is pressed together with the MENU/
ON: Outputs superimposed information, such as time
code, to the connector selected in menu No. 005
SUPER.
DIAG button
, the DIAG screen is displayed.
COUNTER/PF1 button
OFF: No superimposed information is output.
Each time this button is pressed, the counter display on
the display panel changes by one step in the following
sequence: CTL > TC > UB > REM.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions (continued)
Joystick
Front panel (3)
This is used for shuttle, slow and other variable-speed
playback. It is also used for the menu settings, etc.
The stick can be moved upward, downward, to the left or
to the right, and it can also be pressed to initiate
operations. (See “Joystick and Variable Speed
<Note>
When this unit is turnning on, do not use the stick.
Variable-speed playback and menu setting operation
become impossible.
HD
SEARCH button
REC
PB
CH1
CH2
CH1
CH2
When this button is pressed, the search mode is
established.
REC/PB
CH1/5
CH2/6
CH3/7
CH4/8
PB
PLAY button
When this button is pressed, playback starts.
When this button and the REC button are pressed
together, recording starts.
Audio level control knobs
These knobs are used to adjust the recording and
playback level of the PCM audio signals.
REC button
The audio level control selector switch
switches
When this button is pressed together with the PLAY
button, recording starts.
between the recording/playback level adjustment for
CH1/CH2 and the playback level adjustment for CH1 to
CH4.
When it is pressed during playback, a search, fast
forwarding or rewinding, the EE mode pictures and
audio signals can be monitored while it is held down.
When it is pressed in the stop mode, the EE mode
pictures and audio signals can be monitored. (When it is
pressed during playback, the servo will be disrupted.)
When the STOP button is pressed, the original pictures
and sound are restored.
<Notes>
z The level of the IEEE1394 digital input/output audio
signals cannot be adjusted.
z For the recording level, only the analog input can be
adjusted.
Audio level control selector switch
UNITY: At this position, the audio signals are recorded
or played back at a fixed level regardless of the
position of the audio level control knobs
REC/PB:The two switches on the left side of the audio
level control knobs control the recording
REW button
When this button is pressed, the tape is rewound. The
rewinding speed can be selected using menu No.102
FF. REW MAX.
.
FF button
level for the audio signal from analog input CH1/
CH2, and the two switches on the right side
control the playback level for the audio signal for
CH1/CH2.
When this button is pressed, the tape is fast forwarded.
The fast forwarding speed can be selected using menu
No.102 FF. REW MAX.
PB:
At this position, the audio signals for CH1 - CH4
or CH5 - CH8 are played back at the level which
has been adjusted by the audio level control
STOP button
When this button is pressed, the tape stops traveling,
and when “TAPE” has been selected for the menu item
No.140 OUTPUT setting, the still images can be
monitored.
knobs
.
<Note>
When selecting PB, the recording level is UNITY.
Selecting CH1 to CH4 makes the playback level of CH5
to CH8 UNITY while selecting CH5 to CH8 makes the
playback level of CH1 to CH4 UNITY.
Selecting between CH1 to CH4 and CH5 to CH8 can be
performed using menu No. 783 AUDIO CH SEL.
Even in the stop mode, the drum continues to rotate,
and the tape remains in close contact with the drum.
When the stop mode continues beyond a specific time
period, the unit is automatically set to the standby OFF
mode or STEP FWD mode in order to protect the tape.
(This is set using menu item No.400 to 403.)
Immediately after a cassette has been loaded in the
unit, the stop mode is established.
PAUSE button
When this button is pressed during recording, the
recording operation stops temporarily. Restart the
recording by pressing the button again.
When this button is pressed during playback, the screen
changes to a static display. Restart playback by pressing
the button again.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions (continued)
Display panel
!2"
!7" !8"
!10"
!17"
!3" !4" !5"!6"
!11"
!9"
HD
HD
50
SYSTEM DVCPRO
1080i
U
V I D E O
HDSDI
1394 SG
AU D I O
HDSDI
1394 SG
ANALOG
REMOTE
WIDE
COMP
GAMMA
dB
59.94 60
DVCPRO
720p
dB
dB
dB
4
3
2
1
dB
0
50/25PsF
DVCPRO
0
4
3
23.98 24
DV CAM
25
50
2
1
0
-1
-2
-3
-4
CH-15
V F R
HD SD
-12
-20
-12
-20
-12
-20
!16"
!14"
0
AUTO REC
DV CONTROL
EDIT REC INH S
-1
-2
-3
-4
!15"
CTL
TC
UB
26
L R
48
L R
CUE
L R
CH-37
L R
L R
REM
!1"
!12"
!13"
Level meter
COMP lamp
Displays CH1/CH2/CH3/CH4 of the PCM audio signal or
each level of CH5/CH6/CH7/CH8 and the CUE track.
During recording and when the EE mode is selected, it
shows the levels of the input audio signals; during
playback, it shows the levels of the output audio signals.
The audio level display is switched to CH1/CH2/CH3/
CH4 and CH5/CH6/CH7/CH8 by selecting menu No.
783 AUDIO CH SEL. (See page 52)
This lamp turns on when “DARK” is selected in menu
No. 693 COMP MODE.
SYSTEM FREQ display screen
Displays the selections of menu No. 25 SYSTEM FREQ.
VFR (Variable Frame Rate) lamp
This lamp lights when a tape (24/25/50PsF) from a
variable frame rate camera is played back after selecting
the frame rate converter and when conversion is
performed normally.
The audio level display is switched between the FULL
mode and FINE mode using the METER selector button
If the tape and selected frame rate conversion function
for play back do not match, the lamp flashes on and off.
Select the frame rate conversion function in menu No.
25 SYSTEM FREQ. (See page 37)
Reference level
(–20dB: AJ-HD1400P)
Reference level
(–18dB: AJ-HD1400E)
Format displays
The recording format and the format (DVCPRO HD
1080i/DVCPRO HD 720P/DVCPRO 50/DVCPRO/DV/
DVCAM) of the tape inserted in the unit are displayed
here.
FULL mode
FINE mode
FULL mode
FINE mode
INPUT SELECT display area
The characters corresponding to the selected input
signals light up in this area. With the exception of analog
audio signals, flashing appears in this area if the
selected input signals are not available.
REMOTE lamp
This lamp lights when the CONTROL switch has been
set to the REMOTE position.
VIDEO
Repeat lamp
This lights when the repeat play mode has been set.
HDSDI
:
HD serial digital video signals
IEEE1394 digital signals
Internal reference signal
1394:
SG:
U lamp
AUDIO
This lamp lights when UMID information is present on
the input signal in EE mode.
This lamp lights during tape playback when UMID
information has been recorded on the tape.
HDSDI
:
HD serial digital audio signals
IEEE1394 digital signals
Internal reference signal
1394:
SG:
ANALOG: Analog audio signals
WIDE lamp
This lamp turns on when “SQUEEZ” is selected in menu
No. 620 DOWNCON MODE and the down-conversion
output is set to wide screen, or when wide screen
information is recorded on tape when an SD tape is
played back.
GAMMA lamp
This lamp lights when GAMMA function is selected in
menu No.693 GAMMA SEL.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions (continued)
lamp
Backup battery warning lamp
This lamp lights when a cassette tape is inserted into
the VTR.
This lamp displays the voltage condition of the backup
battery for 5 seconds after turning on the power.
In the standby OFF mode, this lamp is flashing.
Steady light
:
The voltage is the specified voltage or
more
Counter display
The tape counter, time code, etc. are displayed here.
The type of value displayed is indicated by CTL, TC, UB
or REM.
Flashing : The backup battery is not installed
properly or the voltage of the backup
battery is less than the specified voltage.
This unit is equipped with a backup mechanism to count
down the time code generator while the power of the
unit is turned off. For details, refer to “Time code when
power is not supplied” (page 56).
The battery must be replaced periodically, since this unit
cannot count down and the numerical value of the time
code generator is reset if the backup battery voltage
drops below the specified value. However, it is not
necessary to replace the battery when it is not
necessary to drive the backup feature.
CTL: This area indicates the tape timer (control signal).
TC: This area indicates time code data.
UB: This area indicates user bit data.
REM: This area indicates the remaining tape time and
total tape duration in minutes.
Example: [30-46]
Remaining tape time: 30 minutes,
Total tape duration: 46 minutes
EDIT/EDIT REC/REC/REC INH lamps
EDIT: This lamp lights when the edit mode is selected.
(9-pin control)
EDIT REC:
<NOTE>
Refer replacement of backup battery to qualified
service personel.
This lamp lights when in the editing record status.
(9-pin control)
REC: This lights in the recording mode.
REC INH:
This lamp lights in the recording prohibited status
(when the front upper REC INHIBIT switch is
“ON” or when the tape was recorded in a format
other than DVCPRO HD-LP and was played back
while “ON” was selected in menu No. 118 SP
MODE INH, or the cassette is in the erase
protection status.)
Recording is not possible while this lamp is
lighted.
Whether the lamp is to light or flash when the
accidental erasure prevention tab on the cassette
tape has been set to the recording inhibit position
can be selected using menu item No.114 REC
INH LAMP.
Channel condition lamps
These lamps light to indicate the error rate status.
Green: This lights when the error rates for the video and
audio playback signals are both at acceptable
levels.
White: This lights when the error rate for the video or
audio playback level has increased.
The playback picture and sound remain
unaffected even while this lamp is lighted.
Red: This lights when the error rate for the video or
audio playback level has increased to the extent
that correction or interpolation was performed.
S (servo) lamp
This lights when both the drum servo and capstan servo
are locked.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions (continued)
Rear panel
TC
HD/SD REF IN
VIDEO OUT
Y
1
P
B
R
IN
HD/SDI
IN
P
OUT1
2
OUT
AUDIO OUT
CH1
(SUPER)
AUDIO IN
CH1
AUDIO
MON
OUT
L
CH2
PUSH
PUSH
CH2
OUT2
AC IN
DC OUT
12V 250mA
SD/SDI
R
R
PUSH
PUSH
E
M
O
R
T
FUSE 250V T2.5AH
F1
DVCPRO
/DV
ENCODER
REMOTE
L
R
SIGNAL
MONITOR
GND
DC IN
AC IN inlet
This is the AC power inlet.
Connect the accessory power cable here.
When both an AC power supply and DC power supply
have been connected, the AC power supply takes
priority.
If an external DC power supply is used, then check the
ratings of the external DC power supply so that they are
compatible with those of this unit. Check the pin
arrangements of the DC output terminal of the external DC
power supply and those of the DC IN socket of this unit so
that their polarities are correctly arranged.
If +12 V are supplied to the unit’s GND terminal by
mistake, this may cause fire or injury.
If the polarities of the DC IN connectors of other devices
are incorrect, and the other devices are connected to the
unit by mistake, fire or personal injury may result.
DC IN socket
This is the input connector for the DC 12V supply
voltage.
Use an external DC power supply rated at DC 12 V/7 A
(12 A peak or higher)
<Notes>
When the voltage has dropped to around 10.6V, the
unit’s power is automatically turned off. (When “TYPE-A”
or “TYPE-B” is not selected as the menu item No.180
BATTERY SEL setting)
Even when the supply voltage is restored later, the
power will not automatically come back on. The POWER
switch must be set to OFF and then back to ON several
seconds later.
z If an external DC power supply is used, then make
sure that the external DC power supply is first turned
ON, then this unit is turned ON. Improper operation
may result in a malfunction in the unit due to slow
startup of the output voltage of the external DC power
supply.
z If input exceeds 18 V by mistake, the protection
feature shuts down the power source at around 20 to
35 V. Change the voltage to the regular voltage, and
the unit is available. An AC source cannot be
connected to this terminal.
Pin No.
Signal
1
1
2
3
4
Ground
2
–
–
3
4
DC OUT socket
This is the DC 12V output socket.
+12 V
Power is supplied from here to the external remote
controller (AJ-A95: optional accessory).
The DC power cable is packed together with the AJ-
A95.
Pin No.
Signal
1
2
3
4
Ground
2
1
3
4
–
–
+12 V
Fuse holder
This holds the AC 250 V/2.5 A fuse (time lag type).
External DC adapter
<Note>
Use the fuse specified by Panasonic.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions (continued)
VIDEO OUT (1, 2, Y, PB, PR) connectors
REMOTE CONTROL connector
By changing the menu item No.615 V OUT SEL setting,
either analog composite signals or HD analog
component Y signals are output from the VIDEO OUT1
connector.
Analog composite signals with superimposed information
embedded can be output from the VIDEO OUT2 connector.
Whether superimposed information is to be embedded
in the signals is selected using menu item No.005
SUPER.
An external remote controller is connected here to
enable the unit to be operated using an external device.
<Notes>
z Set the LOCAL/REMOTE switch to REMOTE.
z The connector satisfies the RS-422A interface
standard.
Pin No.
Signal
1
2
3
4
5
6
7
8
9
Frame Ground
Transmit A
<Note>
1
5
6
9
When HD analog component output or HD SDI output
signals are output with the 60 Hz or 24 Hz system
frequency, the SD SDI signals will be output without the
sync signals (NO SYNC), and the analog composite
signals will be output in the black-and-white mode (burst
OFF).
Receive B
Receive Common
–
Transmit Common
Transmit B
Receive A
TC IN connector
This is used to record an external time code onto the
tape.
Frame Ground
Fan motor
This is provided to cool off the unit.
TC OUT connector
This is used to output the playback time code during
playback.
During recording, the time code generated by the
internal time code generator is output from this
connector.
Grips
This is the handle for carrying the unit.
ENCODER REMOTE connector
Connect a connector encoder remote controller when
externally adjusting each setting of the video output signal.
HD/SD REF VIDEO IN connector and OUT
connector
Pin No.
Signal
Input connector for the HD/SD reference video signal
and loop through output connector.
1
4
FRAME GROUND
REM(G)
<Notes>
REM RX (X)
7
8
z When inputting an HD reference signal to the
connector, input a tri-level sync signal with positive
and negative polarities. Also, supply signals matching
the input signals and tape format.
z When inputting an SD reference signal to the
connector, use a black burst signal which satisfy the
SMPTE170M or ITU624-4 standard.
REMOTE CONTROL PROTOCOL RECEIVE
REM TX (X)
REMOTE CONTROL PROTOCOL TRANSMIT
REM RX (Y)
14
15
REMOTE CONTROL PROTOCOL RECEIVE
REM TX (Y)
REMOTE CONTROL PROTOCOL TRANSMIT
z If no cable is connected to the REF VIDEO OUT
connector, the REF VIDEO IN connector will be 75 h
automatically. If the cable is connected, the 75 h
connection is cancelled.
HD SERIAL COMPONENT AUDIO VIDEO IN/
OUT connector
These are input-output connectors for the HD digital
component audio/video signal conforming to the
SMPTE 292M, 296M or 299M standard.
AUDIO IN connectors (CH1, CH2)
These are the input connectors for the analog audio
signals.
SD SERIAL COMPONENT AUDIO VIDEO OUT
connector
These are output connectors for the digital component
audio/video signal conforming to the SMPTE 259M-C,
272M-A standard.
They are output during DVCPRO50, DVCPRO, DV or
DVCAM interchangeable playback or when signals are
down-converted and output.
AUDIO OUT/MONITOR connector
(CH1, CH2, Lch, Rch)
These are the output connectors for the analog audio
signals.
It is possible to interlock Lch/Rch to the volume control
knob for headphones by adjusting menu No. 712 MONI
OUT appropriately.
<Note>
AUDIO MONITOR connectors
When in 23.98/24 Hz mode, SD SDI output, the system
phase of analog composite video output may change to
match the phase of HD SDI output when tape speed is
at the standard rate.
These are the audio monitor output connectors.These
connectors output the monitor selection channels.
It is possible to interlock these connectors to the volume
control knob for headphones by adjusting menu No. 712
MONI OUT appropriately.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions (continued)
IEEE1394 digital input/output connector
This unit is capable of input and output through a digital
interface conforming to the IEEE1394 standard. Use 6-
pin connectors. Does not support bus power.
Reference signals
During tape playback, the video output reference signals are as shown in the table below.
In the 59.94 Hz/60 Hz or 50 Hz mode
Input signals
REF_IN
Menu item No.031
HD_REF
1
INPUT
Input
AUTO
SD_REF
Internal SD
Internal SD
SD_REF_IN
SD_REF_IN
Internal SD
Internal SD
INPUT*
INPUT
HD_REF_IN
HD_REF_IN
SD_REF_IN
SD_REF_IN
INPUT
HD_REF_IN
HD_REF_IN
Internal HD
Internal HD
Internal HD
Internal HD
HD_REF_IN
SD_REF_IN
None
Not input
Input
Internal HD
INPUT
Not input
Input
Internal SD
INPUT
Not input
Internal HD
Internal HD
*1 If “1394” or “INT SG (internal standard signal)” is selected for the video input signal, the video output reference signal will always be
“Internal HD.”
<Notes>
z When “E-AUTO” is selected in menu No. 031 OUT REF, the unit operates as if “INPUT” is selected in edit mode or “AUTO”
is selected in modes other than the edit mode.
z When using the SD > HD up-converter and HD > HD cross-converter, input the HD tri-level sync signal that supports the
HD output format in order to initiate operation using HD_REF_IN.
In the 23.98 Hz/24 Hz mode
Input signals
REF_IN
HD_REF_IN
None
HD_REF_IN
Internal HD
In the 25 Hz (HD), 25 Hz (SD), 50 Hz (HD) or 50 Hz (SD) mode
Input signals
Menu item No.031
REF_IN
HD_REF_IN
SD_REF_IN
None
AUTO
HD_REF
SD_REF
Internal SD
SD_REF_IN
Internal SD
INPUT
HD_REF_IN
SD_REF_IN
Internal HD
HD_REF_IN
Internal HD
Internal HD
Internal HD
Internal HD
Internal HD
<Notes>
z In the 25 Hz (HD) or 50 Hz (HD) mode, black signals are output from the SD SDI output and analog composite output
connectors.
z In the 25 Hz (SD) or 50 Hz (SD) mode, black signals are output from the HD SDI output and analog component output
connectors.
z All the HD SDI output, SD SDI output, video output, analog component output, audio output and TC output signals are
output in phase with the REF input.
Internal HD:
With HD tape playback as the reference, operation uses a 74 MHz clock signal in the free-run mode.
Internal SD:
With SD tape playback as the reference, operation uses a 4fsc clock signal in the free-run mode.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference frequencies
During tape playback, the video output reference frequencies are as shown in the table below.
In the 59.94 Hz/60 Hz or 60 Hz mode
Input signals
Menu item No.031
REF_IN
INPUT
AUTO
HD_REF
SD_REF
INPUT
Complies with
HD REF IN
frequency
Complies with
INPUT
frequency
Complies with
HD REF IN
frequency
Input
Not input
Input
59.94Hz
HD_REF_IN
Complies with
HD REF IN
frequency
Complies with
menu item No.030
frequency
Complies with
HD REF IN
frequency
59.94Hz
59.94Hz
59.94Hz
59.94Hz
59.94Hz
Complies with
menu item No.030
frequency
Complies with
INPUT
frequency
59.94Hz
59.94Hz
SD_REF_IN
Complies with
menu item No.030
frequency
Complies with
menu item No.030
frequency
Not input
Input
Complies with
INPUT
frequency
Complies with
menu item No.030
frequency
Complies with
INPUT
frequency
None
Complies with
menu item No.030
frequency
Complies with
menu item No.030
frequency
Complies with
menu item No.030
frequency
Not input
<Notes>
z During SD tape playback, operation is not possible in the 60 Hz mode.
z When the HD SDI output signals are output at 60 Hz/24 Hz, the SD SDI signal is output in the NO SYNC status, and the
analog composite signals are output in black-and-white mode (burst OFF).
z All the HD SDI output, SD SDI output, analog composite output, analog component output, audio output and TC output
signals are output in phase with the REF input.
When “90H” is selected as the menu item No.26 HD SYS H ADV, the HD output is output with a phase 90H ahead of the SD
output.
When the SD REF signal is input, the REF input and SD output signals are inphase, and when the HD REF signal is input,
the REF input and HD output signalsare in-phase.
z The audio output and TC output signals are output in-phase with the HD output signals.
z With the 720p format, there is a phase difference of 120H.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Tapes
M cassette guide
HD
REC
PB
CH1
CH2
CH1
CH2
CH1/5
CH2/6
CH3/7
CH4/8
PB
M cassette size
L cassette size
Align the center of the cassette with the
center of the insertion slot, and press it in
gently.
The cassette tape will load automatically.
Consumer-use DV and DVCAM cassettes
(Standard DV and DVCAM cassettes, mini DV and
DVCAM cassettes)
z Use a cassette adapter (AJ-CS455P) when a mini DV or
DVCAM cassette is to be used.
Note that inserting a mini DV or DVCAM cassette without
the use of a cassette adapter will cause malfunctioning.
Also note that long-duration mini DV cassettes (80 minutes
in the standard mode and 120 minutes in the LP mode)
cannot be used.
z It is not possible to play back tapes which have been
recorded in the LP mode.
z When editing material recorded on a consumer-use DV or
DVCAM cassette, first record the material on a DVCPRO
tape or other tape used by VTRs for broadcast
applications.
<Notes on cassette insertion>
z Set the cassette level with the cassette slit and insert
straight.
z Do not put your hand in the cassette slit.
z Insert an M-cassette between the left/right M-cassette
guides.
z If the cassette slit is exposed to the strong direct rays of
the sun, a malfunction in the tape travel may occur.
M cassettes
Tapes capable of up to 33 minutes of recording or playback
(AJ-HP33EMG: for AJ-HD1400E)
L cassettes
Tapes capable of up to 64 minutes of recording or playback
(AJ-HP64ELG: for AJ-HD1400P and AJ-HD1400E)
z The maximum transport speed of a mini DV or DVCAM
cassette tape is 32k.
z The images may be subject to disturbance during the slow
motion playback of consumer-use DV and DVCAM
cassette tapes.
z From the perspective of protecting consumer-use DV and
DVCAM cassette tapes, minimize the number of times the
tapes are cued up at the same locations as much as
possible.
z When consumer-use DV and DVCAM cassette tapes are
used, the maximum time for STILL TIMER is set to 10
seconds.
It is recommended that tapes bearing the Panasonic
brand be used as the consumer-use DV tapes.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Example of connections with an editing controller
Recorder
AV monitor
Analog composite
signals
Audio monitor
signals
To REMOTE CONTROL
connector
AV monitor
Editing controller
AG-A850 etc.
Reference signal
generator
AV switcher
To REMOTE CONTROL
connector
To REMOTE CONTROL
connector
Reference signal
Source unit
Source unit
AV monitor
AV monitor
<Notes>
z When disconnecting the remote signals (9P) from one component and re-connecting them to another component,
check the settings,etc. of the editing controller.
z If the editing operation is executed via the 1394 connection, errors may occur in the editing.
z If the JOG/VAR operates at a half speed or less, errors may occur in the CTL count.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
IEEE1394 digital interface
Settings for this unit
Precautions for use
Confirm that menu No. 882 DIF IN CH and No. 883 DIF OUT
CH of this unit are set to “AUTO.”
z Connect the interface with another device on a 1:1 basis.
z If the E-92 warning (1394 INITIAL ERROR) is displayed,
either re-connect the connecting cable or turn the VTR’s
power off and back on.
Input-output of the digital input signal is enabled when “59/
60” is selected in menu No. 25 SYSTEM FREQ and
operated in 59.94 Hz. Input-output of the digital input signal
is enabled when “50i/25P” is selected in menu No. 25
SYSTEM FREQ as well.
z The AV signals may be disrupted when the power of the
connected devices is turned on or off and when the
interface cable is connected or disconnected.
z When the input signals are switched or the mode is
transferred, it may take a few seconds for the system to
stabilize. Proceed with the recording operation only after
the system has stabilized.
z The following situation applies when recording is to be
performed by selecting the IEEE1394 digital interface
input, and it applies with the signals which are output by
the IEEE1394 digital interface.
<Notes>
z The incoming signal is limited to the format selected in
menu No. 020 SYSTEM FORMAT.
z The output format is determined according to the list
shown below.
Playback format
DVCPRO HD-LP,
DVCPRO HD
DVCPRO50
DVCPRO
Output data format
DVCPRO HD,
DVCPRO50, DV*
DVCPRO50, DV*
DVCPRO, DV
DV
Š The audio level control knobs on the front panel do not
work. The settings in menu No. 680/681/695 are
ignored and the blanking will not be applied.
Š When playback signals other than regular 1a speed
playback signals have been input, no guarantees are
made for the pictures and sound which will be
recorded or for the EE-type pictures and sound.
z The following situation applies when the video input
selection has been set as the IEEE1394 digital interface.
Š The SDI signals, the analog video output signals and
time code output signals become irregular in the EE
mode. Do not use these signals for recording
purposes. (The teletext signals and other signals
superimposed onto the video output signals also
become irregular.)
DV, DVCAM
For EE mode or recording/editing
(Including scene-to-scene
continuity)
z Select a value other than "1394"
with the INPUT SELECT button
on the front panel.
DVCPRO HD*
* CH1/CH2 or CH3/CH4 can be selected as the output audio
channel.
With the following setting, the signal is not output from the
IEEE1394 digital interface.
z During SLOW/STILL playback, unprocessed video and
audio signals are output as the IEEE1394 digital interface
output. When these video and audio signals are monitored
using another device, they may differ from the video and
audio signals played back by this unit.
z When “23/24,” “25 (HD),” “25 (SD),” “50 (HD),” or “50 (SD)” is
selected in menu No. 025 SYTEM FREQ
z When the unit operates in 60 Hz/24 Hz
When the equipment for non-linear editing is connected to
this unit, do not start any other application program than
software for the non-linear edit. Non-linear editing
equipment may garble the output video picture.
Be absolutely sure not to defeat the following
safeguards when connecting the IEEE1394
cable.
(1) Ensure that the unit and all devices to be
connected are grounded (or connected to a
common ground).
If the equipment cannot be grounded, first turn off
the power of all the connected devices, and then
disconnect and re-connect the IEEE1394 cable.
(2) When connecting the unit to a device equipped
with a 4-pin connector, connect the unit’s
connector (6-pin type) first.
(3) When making a connection to a PC equipped
with a 6-pin connector, connect the 1394 cable
so that it mates properly with the 1394
connector. Bear in mind that if the plug is
inserted the wrong way round, the unit may be
damaged as a result.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
VANC data recording/playback
VANC data recording
1 Detects the VANC data packets that multiplex recorded
in the following range of the Y stream of HD SDI.
1080i: L9–L20, L571–L583
720P: L9–L25
<Note>
HANC data packets are not be detected.
2 Records VANC data packets up to the following volume
in the VAUX region of the DVCPRO HD format in the
order of the earlier line.
1080i: 5760 word/frame
720P: 2880 word/frame
<Note>
Data packets that exceed the capacity will not be
recorded or played back.
3
Records the video signal from the HD SDI simultaneously.
<Note>
Recording and playback of VANC data only are not
possible.
VANC data playback
1 If the VTR mode is one of the following, VANC data will
be multiplexed to the Y stream of the HD SDI and will be
played back with the video signal.
z Normal playback mode
z Simultaneous playback mode
z Edit playback mode
z EE mode
<Notes>
z If an operation mode other than the above, such as FF,
REW, JOG, VAR, the video signal will only be played
back by muting VANC data.
z Playback of VANC data only is not possible.
2 VANC data packets will be multiplexed to the same line
of the multiplex line.
<Notes>
z For format conversion playback, the video signal only
will be played back by muting VANC data.
z Metadata recorded on the tape will be output giving
UMID information first priority. When metadata is
output, set to a line other than the original multiplexed
line or select “BLANK.”
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Joystick and Variable Speed Playback
Joystick
4 When the joystick is inclined upward, the tape travels in
1-frame increments in the forward direction; when it is
inclined downward, it travels in 1-frame increments in the
reverse direction.
2
Slow playback is performed if the stick is held at the top
or bottom position.
HD
z If the SEARCH button is pressed while the joystick is
pressed to one side, the current speed is maintained
even if the joystick is released. Pressing the STOP,
PLAY, or other operation buttons cancels the fixed
speed operation.
REC
PB
CH1
CH2
CH1
CH2
REC/PB
CH1/5
CH2/6
CH3/7
CH4/8
<Notes>
PB
z Noise may occur in the video images and voices may be
distorted when tape is replayed at a speed other than the
standard speed (1a).
1
z The PCM audio signal is played back in the –0.9a to
+1.0a speed range, while the CUE signal is played back
at all other speeds. (See menu No. 746 MONI CH SEL
4
3
3
4
Variable Speed Playback
Variable playback speeds are possible by operating the
controller if the 9P remote controller is connected to the
REMOTE CONTROL connector.
1 Press the SEARCH button to activate the joystick.
When “STICK” has been selected as the menu item
No.100 SEARCH ENA setting, the joystick will be
activated without pressing the SEARCH button.
2 Press the joystick to switch between the SHTL mode and
SLOW mode.
3 When the joystick is inclined toward the right, the tape
can be played back in the forward direction at a variable
speed based on the angle that the stick is inclined. When
the stick is inclined toward the left, the tape is played
back in the reverse direction.
z SHTL mode:
The maximum speed which is established when the
joystick has been inclined at the maximum angle
corresponds to the speed which has been set by menu
item No.101 SHTL MAX.
z SLOW mode:
The speed ranges from –0.9a to +1.0a.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PF (Programmable Function)
Three setup menu items can be registered in the PF buttons, and these buttons can then be used to change the setup menu
settings by a simple operating procedure.
<Notes>
Performing operations using the PF
buttons
z The following menu items cannot be saved.
No. Menu item
No. Menu item
1 Open the setup menu by pressing the Menu button, and
move the cursor to the A00 MENU by tilting the joystick
down and then to the right.
05 ENCODER SEL
06 V LEVEL CTRL
12 SYS H (HD)
653 Y LEVEL (HD)
654 Pb LEVEL (HD)
655 Pr LEVEL (HD)
656 BK LEVEL (HD)
658 Y LEVEL (SD)
659 Pb LEVEL (SD)
660 Pr LEVEL (SD)
661 BK LEVEL (SD)
662 V LEVEL
14 SYS SC (SD)
15 VO SYS SC (SD)
16 SD SYS SC (SD)
18 SCH CORS (SD)
19 SCH FINE (SD)
20 AV PHASE
2 Move the cursor to the item with the PF number to be
registered (A04 to A06) by tilting the joystick up and
down.
SETUP-MENU MENU
<USER1>
A02 P.ON LOAD
NO.A04-
OFF
25 SYSTEM FERQ
663 C LEVEL
¢
A04 PF1 ASSIGN 012
A05 PF2 ASSIGN 513
A06 PF3 ASSIGN ---
END
HUE
26 HD SYS H ADV
181 TYPE A NEAR
182 TYPE A END
(AJ-HD1400P)
664
C PHASE
(AJ-HD1400E)
SETUP LVL
(AJ-HD1400P)
665
BK LVL
3 When the joystick is pressed, a list of items which can be
183 TYPE B NEAR
184 TYPE B END
(AJ-HD1400E)
set is displayed.
SETUP-MENU MENU
z As for the menu items registered in the PF button, when
the menu is not displayed due to change of settings in
menu No. 25 SYSTEM FREQ are changed, the registered
contents in the interlocked PF button will be in the “not
saved” state and cannot be displayed nor operated. Refer
<USER1>
NO.A04-
A04 PF1 ASSIGN 012
¢
--- NO ASSIGN
001 LOCAL ENA
002 LOCAL TIMER
003 REMAIN SEL
008 CHARA H-POS
009 REMAIN SEL
010 CHARA V-POS
The settings for the PF buttons are retained but will be
updated once save operations are executed again.
4 Press the joystick to select the item at the cursor
position; the display will then return to the regular menu.
Operation using the PF buttons
5 When the MENU button is pressed, a confirmation
screen is displayed.
1 When the PF button is pressed, the registered items are
displayed on the monitor screen which is output from the
VIDEO MON connector.
Press the PLAY button to finish registering the item in the
PF button.
2 Press the PF1, PF2 or PF3 button that corresponds to
the item whose setting is to be changed. Each time the
button is pressed, the setting is updated in sequence.
PF1:SYS FORMAT 50M
PF2:INT SG
CB75
PF3:---------- ---
3 When the PF button is pressed again, the regular display
is restored. If no operations are made, the display is also
restored automatically after five seconds elapse.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Pause/Recording (Recording with pauses)
1 Press the PAUSE button during playback of the cassette
4 Press the PAUSE button again to pause the recording.
When menu item No. 154 AUTO BACK is set to “REC-P”
or “ALL,” the tape is rewound for a few seconds from the
position where the PAUSE button is pressed, and then
paused.
tape.
2 Press the REC button to move to the REC PAUSE mode.
When menu item No. 154 AUTO BACK is set to “REC-P”
or “ALL,” the tape is rewound for a few seconds from the
position where the PAUSE button is pressed.
5 By repeating the operation in 3 and 4 above, it is possible
to record with pauses.
3 Press the PAUSE button to start recording.
The tape runs to the position where the PAUSE button is
pressed as mentioned in 1 above, and recording starts.
Cue up
When recording with pauses, the time codes of the starting point and the stopping point of the recording are automatically
backed up. However, the “CTL” is selected by using the COUNTER button, and the control signals are backed up.
With the following button operation, it is possible to cue up to the starting and stopping points of the recording.
STOP + REW
Press the REW button while the STOP button is pressed
to cue up to the starting point of the recording.
STOP + FF
<Notes>
z In the backup operation, only the time codes of the last
event recorded with pause are stored.
z Even if the recording is stopped by pressing the STOP
button, the stopping point of the recording is backed up.
z Cueing up from a portion where nothing is recorded
cannot be executed properly.
z If the FF/REW button is pressed during the cue up
operation, the unit moves to the ordinary search mode.
z When the power is turned off, backup data stored when
starting the recording and completing the recording will be
cleared.
Press the REW button while the STOP button is pressed
to cue up to the starting point of the recording.
<Note>
If the time code is not successive, it is impossible to cue up
to the starting point of the recording properly. Execute the
following settings.
z Menu item No. 154 AUTO BACK:
“REC-P” or “ALL”
z Menu item No. 503 TCG MODE:
“REGEN” or “AUTO”
1 Execute the recording with pauses.
2 Press the REW button while the STOP button is pressed.
The tape cues up to the starting point of the recording
with an accuracy of 1 frame.
3 Press the PLAY button to confirm the recording.
4 Press the FF button while the STOP button is pressed.
The tape cues up to the stopping point of the recording
and stops 5 to 10 frames before the stopping point.
5 Press the PAUSE button and then the REC button to
move to the REC PAUSE mode.
The tape cues up to the stopping point of the recording
and stops 5 to 10 frames before the stopping point.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat playback
Setting the BEGIN and END points
Setting the repeat playback mode
1 Press the MENU button.
1 Press the MENU button.
2 Select menu item No. 161 CTL (TC) BGN or No. 162
END, and tilt the joystick right/left while pressing the
SEARCH button.
2 Select menu item No.160 MEMORY MODE, and select
the repeat playback mode.
By operating the joystick, the user can choose whether
or not to set the BEGIN and END points. “--:--:--:--”
appears on the display when the points are not set. If
repeat playback is initiated in this state, the tape start will
serve as the BEGIN point, and the tape end will serve as
the END point.
Item setting
Description of operation
Normal operation
OFF
When the tape is fast forwarded or
rewound, it stops near the BEGIN
point.
M-STOP
REPT1
When the tape is played as far as the
END point, it is rewound to the BEGIN
point where it stops.
3 Press the joystick while the setting is displayed. The
When the tape is played as far as the
END point, it is rewound to the BEGIN
point and played, and this sequence of
operations is repeated.
changed digits flash on the display.
CONT
4 Select TC or CTL using the COUNTER button.
5 Incline the joystick to the left or right, and select the digits
to change (flashing).
3 Press the MENU button.
A confirmation screen now appears. The settings are
stored in the memory if the PLAY button is now pressed.
The frame digits cannot be selected. “00” is always
displayed for these digits.
When the joystick is now inclined upward or downward,
the value of the digits changes.
The counter display is reset to 00:00:00:00 when the
RESET button is pressed.
<Notes>
z The picture quality deteriorates when repeat playback is
initiated for the same tape over and over again. As a
general rule of thumb, replace the tape with a new one
after playing back the tape for about 100 times.
6 After the settings have been completed, press the
z The output images to be displayed while the tape is being
rewound to the BEGIN point in the repeat playback mode
can be set using menu item No.163 REPT MODE.
If “FREEZE” is selected as the REPT MODE setting and
the tape end has been set as the END point, the playback
image will not be frozen properly. Set the END point at a
place on the tape where images have been recorded.
z If the counter display mode (TC or CTL), which was
established when menu item No.161 CTL (TC) BGN and
No.162 END were set, is different from the counter display
mode (TC or CTL) in which repeat playback is to be
initiated, the repeat lamp flashes, and the repeat playback
operation cannot be performed.
joystick.
7 Press the MENU button.
<Note>
The settings for the BEGIN and END points are not stored in
user default. Even if the factory settings and/or the user
defaults are loaded, the settings for the BEGIN and END
points are not revised. For user defaults, refer to “Setup
z When consumer-use DV and DVCAM tapes are used, the
repeat playback mode is disabled.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording from a variable frame rate camera
Recording the HD SDI output signal from
a variable frame rate camera
Connect the HD SDI (720/30Pover 59.94P) output of the
variable frame rate camera to the HD SDI input connector of
this unit.
Field displacement
There is no discriminant information to differentiate between
the first field and the second field in the HD SDI signal of
720P. Accordingly, it is usually necessary to synchronize the
HD SDI signal transmission equipment to the recording
equipment with the reference signal from SD. If not
synchronized, there is a risk of generating displacement
(image frame fails to match the time code) with 1/2
probability described as follows.
1 Select “SLTC” in menu No. 032 REC REF.
Detect the frame information from the superimposed
time code in the HD SDI signal to prevent displacement
of the field.
Variable frame rate camera
2 Adjust the following settings to activate the two settings.
z Menu No. 25 SYSTEM FREQ: 59/60
z Menu No. 020 SYS FORMAT: 720p
z INPUT SELECT button on the front panel: HDSDI
3 Change the mode for this unit to REC PAUSE mode.
4 Press the PAUSE button while confirming the HD SDI
output image of the variable frame rate camera to start
recording.
The time code is recorded to maintain the continuity of
the recorded tape.
The superimposed user bits for the HD SDI signal is
recorded.
720/30P over 59.94P
<Note>
Through the settings in menu No. 032 REC REF, the time
code and the user bits recorded on the tape are as follows.
SLTC:
The time code is recorded to maintain the continuity of
the recorded tape.
The superimposed user bits for the HD SDI signal is
recorded.
The following settings are then invalid.
z TCG switch on the front panel
(REGEN/PRESET/EXT)
AJ-HD1400
z Menu No. 503 TCG_MODE
(SW/AUTO)
z Menu No. 505 TCG_REGEN
(TC&UB/TC/UB)
Video output of variable
frame rate camera
A
A
B
B
C
C
D
D
E
E
F
z Menu No. 507 TC_SOURCE
(EXT_L/SLTC/SVITC)
Time code output of
variable frame rate camera
00 01 02 03 04 05
NORMAL:
Time code and user bits are recorded according to the
following settings.
Record image of VTR
A
B
B
C
C
D
D
E
E
E
z TCG switch on the front panel
(REGEN/PRESET/EXT)
Record time code of VTR
00 01 02 03 04
z Menu No. 503 TCG_MODE
(SW/AUTO)
z Menu No. 505 TCG_REGEN
(TC&UB/TC/UB)
z Menu No. 507 TC_SOURCE
(EXT_L/SLTC/SVITC)
To prevent displacement of this field, select “SLTC” in menu
No. 032 REC REF when recording the HD SDI output signal
from a variable frame rate camera (720/30P over 59.94p)
with this unit.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (initial settings)
This unit’s main settings can be performed and checked using the on-screen menus which are displayed on the video monitor
connected to the unit.
It is also possible to set and confirm using the item number and the setting number or the item name, which are displayed on
the display part on the front panel.
Furthermore, a user setting memory in which to store three sets of settings is provided, enabling the desired settings to be
stored for future use.
5 Incline the joystick right and left while pressing the
SEARCH button at the changing position.
5
2, 3, 4
The set value on the settings screen and the set value in
the counter display flash; the value changes each time
the joystick is inclined right and left. When the set value
is displayed, return the joystick.
HD
In order to return the set value to the factory settings,
press the RESET button while pressing the SEARCH
button.
REC
PB
CH1
CH2
CH1
CH2
6 To change the other items, repeat the process 4, 5, and
6.
CH1/5
CH2/6
CH3/7
CH4/8
PB
7 Press the MENU button.
z When the set value is not changed, the display of the
menu screen disappears.
z When the set value is changed, a confirmation screen
will be displayed.
1, 7
Setting method using the on-screen
menus
z Press the PLAY button to save the changes of the set
value.
z Press the STOP button to cancel the change of the set
value.
1 Press the MENU button.
SETUP-MENU MAIN is displayed on the video monitor,
and the names of the main menu items are displayed in
the counter display.
SETUP-MENU SET OK?
YES<PLAY>/NO<STOP>
SETUP-MENU MAIN
NO.00
¢
00 SYSTEM
000 BASIC
100 OPERATION
200 INTERFACE
300 EDIT
400 TAPE PROTECT
500 TIME CODE
600 VIDEO
700 AUDIO
Returning to the factory settings
2 Incline the joystick up and down to select the main menu
item.
1 Press the MENU button.
A select screen for the major menu items is displayed on
the video monitor and the names of the major menu
items are displayed in the counter display.
The cursor (¢) for the main menu items on the select
screen moves up and down and the names of main
menu items are displayed on the counter display.
2 Press the RESET button.
3 Incline the joystick toward the right to move the cursor on
the settings screen to each item.
The unit is now set to the default setting mode, and the
default setting screen now appears on the video monitor.
The settings screen for each item is displayed on the
video monitor, and the item number in the counter
display will flash. When the FF button is pressed for
about 1.5 seconds, the item name will be displayed in the
counter display. When the FF button is pressed for about
1.5 seconds again, the display returns to the item
number.
SELECT MODE
¢
0 ESCAPE
1 LOAD
2 SAVE
3 PROTECT
In order to return to the SETUP-MENU MAIN screen,
incline the joystick toward the left.
4 Incline the joystick up and down to select the item to
change the setting.
The cursor (¢) on the select screen moves up and down,
and the item number flashes on the counter display.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (initial settings) (continued)
Setting the user defaults
3 Incline the joystick up and down to adjust the cursor in
the default settings screen to the “LOAD” position and
press the joystick. The mode for this unit changes to the
LOAD mode, the LOAD screen is displayed on the video
monitor, and the item name is displayed in the counter
display.
1 Press the MENU button.
A select screen for major menu items is displayed on the
video monitor, and the names are displayed in the
counter display.
desired settings.
SET-UP MENU
NO
<LOAD>
¢
FACTORY
USER1(ALL)
USER2(ALL)
USER3(ALL)
USER1(NOT SYSTEM)
USER2(NOT SYSTEM)
USER3(NOT SYSTEM)
3 Press the RESET button.
The mode for this unit will change to the default setting
mode, and the default setting screen will be displayed on
the video monitor.
SELECT MODE
4 Incline the joystick up and down to adjust the cursor in
the LOAD screen to the “FACTORY” position and press
the joystick.
¢
0 ESCAPE
1 LOAD
2 SAVE
3 PROTECT
z If this operation is made after moving the cursor to
“FACTORY,” values for all menus except the SYSTEM
menu will return to the factory settings.
z When the cursor is moved to “NO” and this operation is
performed, the display returns to the menu screen
without restoring the factory settings.
4 Incline the joystick up and down to adjust the cursor in
the default settings screen to the “SAVE” position and
press the joystick.
5 The confirmation screen is displayed on the video
monitor.
The mode for this unit changes to the SAVE mode, the
SAVE screen is displayed on the video monitor, and the
item name is displayed in the counter display.
z When the PLAY button is pressed, the unit returns to
the factory settings and the display of the menu screen
disappears.
z When the STOP button is pressed, the display returns
to the menu screen without changing the settings.
SET-UP MENU
NO
<SAVE>
¢
USER1(ALL)
USER2(ALL)
USER3(ALL)
SETUP-MENU <LOAD>
USER1(NOT SYSTEM)
USER2(NOT SYSTEM)
USER3(NOT SYSTEM)
FACTORY OK?
YES<PLAY>/NO<STOP>
5 Incline the joystick up and down to adjust the cursor on
the SAVE screen to the “USER ¢ (ALL)” position (¢
each value from 1 to 3.) and press the joystick.
z When storing a set value other than SYSTEM menu in
memory, move the cursor to “USER
¢
(NOT
SYSTEM)” (¢ each value from 1 to 3.) and press the
joystick.
z To cancel the operation, move the cursor to “NO” and
press the joystick.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (initial settings) (continued)
6 Confirmation screen for SAVE is displayed.
4 Incline the joystick up and down to adjust the cursor on
the LOAD screen to the “USER ¢ (ALL)” (¢ each value
from 1 to 3.) position and press the joystick.
z When the PLAY button is pressed, the set value is
stored and the display returns to the menu screen.
z When the STOP button is pressed, the display returns
to the menu screen without storing the set value.
z When loading a set value other than SYSTEM menu in
memory, move the cursor to “USER
¢
(NOT
SYSTEM)” (¢ each value from 1 to 3.) and press the
joystick.
z To cancel the operation, move the cursor to “NO” and
press the joystick.
SET-UP MENU
USER1(ALL) OK?
YES<PLAY>/NO<STOP>
<SAVE>
5 LOAD confirmation will be displayed.
z When the PLAY button is pressed, the set value is
loaded and the display of the menu screen disappears.
z When the STOP button is pressed, the display returns
to the menu screen without loading the set value.
7 When the MENU button is pressed, the display of the
menu screen disappears.
SET-UP MENU
USER1(ALL) OK?
YES<PLAY>/NO<STOP>
<LOAD>
User default loading method
1 Press the MENU button.
A select screen for the major menu items is displayed on
the video monitor, and the names are displayed in the
counter display.
2 Press the RESET button.
The unit is now set to the default setting mode, and the
default setting screen now appears on the video monitor.
SELECT MODE
¢
0 ESCAPE
1 LOAD
2 SAVE
3 PROTECT
3 Incline the joystick up and down to adjust the cursor on
the default settings screen to the LOAD position and
press the joystick.
The mode for this unit changes to the LOAD mode, the
LOAD screen is displayed on the video monitor, and the
item name is displayed in the counter display.
SET-UP MENU
NO
<LOAD>
¢
USER1(ALL)
USER2(ALL)
USER3(ALL)
USER1(NOT SYSTEM)
USER2(NOT SYSTEM)
USER3(NOT SYSTEM)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (initial settings) (continued)
Menu protection method
Menu protection release method
By switching to the menu protect mode, it is possible to
disable the setup menu even if the MENU button on the front
panel is pressed.
1 Press the MENU button when pressing the COUNTER
button on the front panel.
A select screen for the major menu items is displayed on
the video monitor, and the names are displayed in the
counter display.
1 Press the MENU button.
A select screen for the major menu items is displayed on
the video monitor, and the names are displayed in the
counter display.
2 Execute the procedures from 2 to 3 described in the
“Menu protection method.”
The unit will be set to the menu protect setting mode, and
the display for confirming menu protection will appear on
the video monitor.
2 Press the RESET button.
The unit will switch to the default setting mode, and the
default screen will be displayed on the video monitor.
MENU PROTECT OK?
SELECT MODE
YES<PLAY>/NO<STOP>
¢
0 ESCAPE
1 LOAD
2 SAVE
3 PROTECT
3 Press the STOP button.
3 Tilt the joystick up/down to move the cursor to the
“PROTECT” position on the default screen and then
press the joystick.
The menu is displayed.
4 Press the MENU button.
The unit enters the menu protect setting mode, and the
confirmation screen is displayed on the video monitor.
The menu disappears, and the menu protect mode is
released.
MENU PROTECT OK?
YES<PLAY>/NO<STOP>
4 Press the PLAY button.
The menu is displayed.
5 Press the MENU button.
The menu disappears and the unit will switch to the
menu protect mode.
z If the MENU button is pressed while the menu protect
mode is set, the message <MENU PROTECT> is
displayed on the video monitor and the menu is
displayed.
<Note>
To enable ordinary menu operation while the menu
protection mode is set, press the MENU button when
pressing the COUNTER button on the front panel.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup (initial settings) (continued)
System frequency switching
<Selection of the record and playback format and the synchronizing signal depends on the operation mode>
NO.25
SYSTEM
FERQ
Recordable format
Playback permissible format
Synchronized signal
1080/59.94i (HD_LP)
720/59.94p (HD_LP)
720/60.00p (HD_LP)
(Only the variable frame rate
signal can be recorded.)
1080/59.94i
1080/60i
720/59.94p
720/60.00p
HD_REF (59.94Hz, 60Hz)
SD_REF (59.94Hz)
59/60
According to the setting in menu
No. 031 OUT REF.
480/59.94i (50M, 25M, DV, DVCAM)
HD_REF (50Hz)
SD_REF (50Hz)
1080/50i
720/50p
576/50i (50M, 25M, DV, DVCAM)
576/25p over 50i (50M, 25M, DV)
1080/50i (HD_LP)
720/50p (HD_LP)
50i/25P
According to the setting in menu
No. 031 OUT REF.
1080/23.98p over 59.94i [2:3 mode]
1080/23.98p over 59.94i [2:3:3:2 advance mode]
720/23.98p over 59.94p
23/24
None
HD_REF (47.96Hz, 48Hz)
720/24p over 60.00p
480/23.98p over 59.94i [2:3 mode]
480/23.98p over 59.94i [2:3:3:2 advance mode]
HD_REF (50Hz)
SD_REF (50Hz)
25 (HD)
25 (SD)
50 (HD)
50 (SD)
None
None
None
None
720/25p over 60p
720/25p over 60p
720/50p over 60p
720/50p over 60p
According to the setting in menu
No. 031 OUT REF.
HD_REF (50Hz)
SD_REF (50Hz)
According to the setting in menu
No. 031 OUT REF.
HD_REF (50Hz)
SD_REF (50Hz)
According to the setting in menu
No. 031 OUT REF.
HD_REF (50Hz)
SD_REF (50Hz)
According to the setting in menu
No. 031 OUT REF.
Procedure for shifting the system frequency
To shift the system frequency execute the following operations.
1 Change the set value of menu item No. 25 SYSTEM
FREQ. For the method to change the set value, refer to
Once the set value is changed, the outer frame of the
display part of SYSTEM FREQ and the characters in
SYSTEM on the front display panel start flashing.
3 The confirmation screen is displayed to enable the
changed set value.
SETUP-MENU SET OK?
YES<PLAY>/NO<STOP>
S
ystem menu item
No.25
(SYSTEM FREQ) setting
has been changed.
SYSTEM
59.94 60
50/25PsF
23.98 24
25
50
HD SD
z To enable the change to set value, press the PLAY
button. Then the system resumes and starts again in
the selected mode.
z To disable the change to the set value, press the STOP
button. Any other changes in the set up menu items
are also disabled.
2 Press the MENU button.
<Note>
If the system is restarted when a cassette remains in the
unit, the cassette will automatically be ejected.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus
Menus which are displayed
The menus displayed differ depending on the setting selected for menu item No.25 SYSTEM FREQ.
Menu No.25 SYSTEM FREQ
NO.
05 ENCODER SEL
Item
59/60
23/24
50i/25P
25 (HD)
25 (SD)
50 (HD)
50 (SD)
06 V LEVEL CTRL
12 SYS H (HD)
14 SYS SC (SD)
15 VO SYS H (SD)
16 SD SYS H (SD)
18 SCH COAR (SD)
19 SCH FINE (SD)
20 AV PHASE
25 SYSTEM FREQ
26 HD SYS H ADV
001 LOCAL ENA
002 TAPE TIMER
003 REMAIN SEL
005 SUPER
No
No
No
No
No
No
No
No
No
No
No
006 DISPLAY SEL
007 CHARA H-POS
008 CHARA V-POS
009 CHARA TYPE
020 SYS FORMAT
022 PB FORMAT
023 FORMAT SEL
030 HD FREQUENCY
031 OUT REF
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
032 REC REF
100 SEARCH ENA
101 SHTL MAX
102 FF. REW MAX
104 REF ALARM
105 AUTO EE SEL
106 EJECT EE SEL
107 EE MODE SEL
108 PLAY DELAY
109 CAP. LOCK
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
110 AUTO REW
112 FRZ MODE SEL
114 REC INH LAMP
115 EJECT SW INH
118 SP MODE INH
119 CONFI REC
134 ARARM BEEP
140 OUTPUT
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
152 HUMID OPE
154 AUTO BACK
155 AUTO REC
No
No
No
No
No
No
No
No
No
No
160 MEMORY MODE
161 CTL BGN/TC BGN
162 END
163 REPT MODE
180 BATTERY SEL
181 TYPE-A NEAR
182 TYPE-A END
183 TYPE-B NEAR
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
Menu No.25 SYSTEM FREQ
NO.
184 TYPE-B END
Item
59/60
23/24
50i/25P
25 (HD)
25 (SD)
50 (HD)
50 (SD)
190 V IN SEL INH
191 A IN SEL INH
202 ID SEL
No
No
No
No
No
No
No
No
No
No
302 CONFI EDIT
303 AUD EDIT IN
304 AUD EDIT OUT
307 AFTER CUE-UP
320 EDIT RPLCE1
321 EDIT RPLCE2
322 EDIT RPLCE3
323 EDIT RPLCE4
324 EDIT RPLCEC
400 STILL TIMER
401 SRC PROTECT
402 DRUM STDBY
403 STOP PROTECT
500 VITC BLANK
501 VITC POS-1
502 VITC POS-2
503 TCG MODE
504 RUN MODE
505 TCG REGEN
506 REGEN MODE
507 EXT TC SEL
508 BINARY GP
509 PHASE CORR
510 TCG CF FLAG
511 DF MODE
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
512 TC OUT REF
513 VITC OUT
514 HD EMBD VITC
515 HD EMBD LTC
601 VIDEO INT SG
602 SDI IN MODE
603 V-MUTE SEL
604 FREEZE SEL
615 V OUT SEL
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
619 V_FILTER
No
No
No
620 DOWNCON MODE
621 UPCONV MODE
626 D/C ENH H
No
627 D/C ENH V
628 U/C ENH H
No
No
No
No
No
No
No
No
No
No
629 U/C ENH V
630 1080i>HD_OUT
632 720p>HD_OUT
636 SD>HD_OUT
650 STYLE
No
No
No
No
No
651 HUE STYLE (SD)
653 Y LVL (HD)
No
No
No
No
654 Pb LVL (HD)
655 Pr LVL (HD)
656 BK LVL (HD)
658 Y LVL (SD)
659 Pb LVL (SD)
660 Pr LVL (SD)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
Menu No.25 SYSTEM FREQ
NO.
661 BK LVL (SD)
Item
59/60
23/24
50i/25P
25 (HD)
25 (SD)
50 (HD)
50 (SD)
662 V LEVEL
663 C LEVEL
664 HUE
665 SETUP LVL
676 BLK CLIP
680 CC (F1) BLANK
681 CC (F2) BLANK
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
682 VO SETUP (HD) (For AJ-HD1400P)
683 VO SETUP (SD) (For AJ-HD1400P)
684 EDH (SD)
685 ESR MODE (SD)
686 CCR MODE (SD)
687 SDI INDEX 0
689 COMP MODE
690 UMID REC
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
691 UMID GEN
692 UMID POS
693 GAMMA SEL
695 BLANK LINE
701 CH1 IN LV
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
702 CH2 IN LV
706 CH1 OUT LV
707 CH2 OUT LV
710 MONIL OUT LV
711 MONIR OUT LV
712 MONI OUT
724 REC CH3/4
No
No
No
No
No
No
No
No
No
No
730 REC CUE
731 PB FADE
732 EMBEDDED AUD
746 MONI CH SEL
750 ANA CH1/2 SEL
759 DV PB ATT
No
No
No
No
No
No
No
No
No
No
760 REC PT MUTE
762 AUD RATE CON
765 CUE OUT SEL
781 IN IMP SEL
No
No
No
No
No
782 EMB CH SEL
783 AUDIO CH SEL
784 MONI SEL INH
880 DIF SPEED
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
882 DIF IN CH
883 DIF OUT CH
886 DIF CONFIG
890 DIF AUD OUT
891 DIF DV AUDIO
892 DIF SIG CMD
894 HD>DIF OUT
895 50M>DIF OUT
896 25M>DIF OUT
899 DIF SUPER
A02 P. O N L O A D
A04 PF1 ASSIGN
A05 PF2 ASSIGN
A06 PF3 ASSIGN
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
When “CMPST” has been selected as the menu item No.650
STYLE setting
Video output signal adjustments
The control matrix for the adjustments is shown in the table
below.
Setting
Adjustment item
This function is not available for IEEE1394 digital output.
662: V LEVEL
663: C LEVEL
664: HUE
When “CMPNT” has been selected as the menu item No.650
STYLE setting
05:
ENCODER SEL
665: SETUP LVL
Setting
Adjustment item
LOCAL
AJ-HD1400
653: Y LVL (HD) 658: Y LVL (SD)
654: Pb LVL (HD) 659: Pb LVL (SD)
655: Pr LVL (HD) 660: Pr LVL (SD)
656: BK LVL (HD) 661: BK LVL (SD)
05:
06:
External encoder
remote controller
/AJ-HD1400
ENCODER V LEVEL
BOTH
SEL
CTRL
HD
AJ-HD1400:
LOCAL
SD
AJ-HD1400
AJ-HD1400
Only adjustments of the setup menu items are
performed.
External encoder remote controller/AJ-HD1400:
Adjustments can be performed from both the external
encoder remote controller and setup menus.
BOTH
External encoder
remote controller/ AJ-HD1400
AJ-HD1400
HD
External encoder
BOTH
SD
AJ-HD1400
remote controller/
AJ-HD1400
<Notes>
z Use the MT-200/2000 (manufactured by Musashi and
recommended by Panasonic) as the external encoder
remote controller. However, its VIDEO PHASE, SYNC
PHASE and SC PHASE controls will not work.
During menu operations and operations using the PF
function, operations from the external encoder remote
controller cannot be accepted.
z Both the HD and SD can be controlled at the same time
regardless of the setting of the menu No.06 V LEVEL
CTRL.
External encoder External encoder
remote controller/ remote controller/
BOTH
AJ-HD1400
AJ-HD1400
AJ-HD1400:
Only adjustments of the setup menu items are
performed.
External encoder remote controller/AJ-HD1400:
Adjustments can be performed from both the external
encoder remote controller and setup menus.
<Notes>
z Use the AJ-ER50 as the external encoder remote
controller. However, its “VIDEO PHASE” and “SYNC
PHASE” controls will not work.
z During menu operations and operations using the PF
function, operations from the external encoder remote
controller cannot be accepted.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
SYSTEM
No./Item
Description of setting
No./Item
Description of setting
05
For setting whether to perform the various
adjustments for the video output signals using this
VTR or using an external encoder remote controller.
15
For adjusting the system phase of the analog
composite output signals (in 37 ns increments).
– :Phase advances.
ENCODER
SEL
VO SYS H
(SD)
0001
LOCAL
:
+ :Phase delays.
The various adjustments for the video output
signals are performed using this VTR.
0000
:
0858
:
1716
<Note>
–858
:
0
0002
BOTH :
The various adjustments for the video output
signals are performed using both this VTR and an
external encoder remote controller.
:
858
<Notes>
The setting range is –864 to 0 to 864 when 50i/25P,
25 (HD) or 25 (SD) is selected as the menu item
No.25 SYSTEM FREQ setting.
z If the signals are adjusted with the external
encoder remote controller, the adjusted values are
reflected in the setup menu. However, the adjusted
numerical values will not be stored unless about 1
minute has elapsed after completion of the
adjustment operation. If the unit is turned off after
executing the adjustments with the external
encoder remote controller, it is necessary to wait
about 1 minute before turning off the power.
z Settings in this menu are not effective for the
IEEE1394 digital output.
16
For adjusting the system phase of the SD SDI output
signals (in 37 ns increments).
– :Phase advances.
SD SYS H
(SD)
+ :Phase delays.
0000
:
0858
:
–858
:
0
:
1716
<Note>
858
The setting range is –864 to 0 to 864 when 50i/25P,
25 (HD) or 25 (SD) is selected as the menu item
No.25 SYSTEM FREQ setting.
06
V LEVEL
CTRL
For selecting what is to be controlled when the video
output level is to be adjusted by an external encoder
remote controller.
18
For adjusting the SCH (sub-carrier to horizontal)
phase of the analog composite output signals (4
positions in 90-degree increments).
The SC phase changes, and the H phase remains
unchanged.
0000
HD :
SCH
COAR
(SD)
The HD video output level can be adjusted.
0001
SD :
The SD video output level can be adjusted.
0002
BOTH :
0000
0001
0002
0003
0
90
180
270
Both the HD and SD video output levels can be
adjusted.
<Note>
When “CMPST” is selected in menu No. 650 STYLE,
the unit will be in the same state as when “BOTH” is
selected, regardless of the settings in this item.
19
For adjusting the SCH (sub-carrier to horizontal)
phase of the analog composite output signals
(variable range of over 45 degrees).
The SC phase changes, and the H phase remains
unchanged.
A range of 180 degrees is covered by using this
setting in combination with item No.18 SCH COAR
(SD).
SCH FINE
(SD)
12
SYS H
(HD)
For adjusting the system phase of the HD SDI output
signals. (in 13.5 ns increments).
– :Phase advances.
+ :Phase delays.
0000
:
–1100
:
0000
:
–32
:
1100
:
0
:
0032
:
0064
0
:
32
2200
1100
<Notes>
z When menu item No. 25 SYSTEM FREQ is set to
50i/25P, 25 (HD), 25(SD), 50 (HD) or 50 (SD), the
setting range is from –1320 - 0 - 1320.
z When menu item No. 25 SYSTEM FREQ is set to
23/24, the setting range is from –1375 - 0 - 1375.
20
AV
PHASE
For adjusting the phase of the AUDIO output signals
in relation to the video output signals (in 20.8 µs
increments).
– :Audio phase against image advance.
+ :Audio phase against image delay.
14
SYS SC
(SD)
For adjusting the system phase of the analog
composite output and SD SDI output signals (total
variable range of over 180 degrees).
– :Phase advances.
0000
:
0100
:
–100
:
0
:
+ :Phase delays.
0200
100
0000
–108
:
:
0
:
“_____” indicates the factory setting.
0108
:
0216
108
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
SYSTEM (continued)
BASIC
No./Item
Description of setting
No./Item
Description of setting
25
SYSTEM
FREQ
For selecting the system frequency.
For details, refer to “Procedure for shifting the system
001
LOCAL
ENA
For setting the operable buttons on the front panel
when the REMOTE/LOCAL switch is set to
“REMOTE.”
0000
59/60
:
0000
DIS :
The 59.94 Hz or 60 Hz system frequency is
selected.
None of the buttons can be operated.
0001
ST&EJ :
0001
50i/25P
:
Only the STOP and EJECT buttons can be
operated.
The 50 Hz or 25 PsF system frequency is selected.
At this setting, the 1080/25 PsF format signals can
be recorded and played back in the same way as
with the 1080/50i format.
0002
ENA1 :
All of the buttons with the exception of COUNTER
and RESET can be operated.
0002
23/24 :
0003
ENA2 :
The 23.98 Hz or 24 Hz system frequency is
selected.
All of the buttons can be operated.
002*1
TAPE TIMER
For setting how the time is to be displayed on the CTL
counter display.
0000
12-hour display
0001
0003
25(HD)
:
The 25 Hz system frequency is selected. However,
black signals are output from the SD SDI output
and analog composite connectors.
12h :
24h :
0004
25(SD) :
24-hour display
The 25 Hz system frequency is selected. However,
black signals are output from the HD SDI output
and analog component connectors.
003
REMAIN SEL
For setting the remaining time on the tape for the
respective connectors and the superimposed
indications of the total length of the tape.
0005
50(HD) :
0000
OFF :
The 50 Hz system frequency is selected. However,
black signals are output from the SD SDI output
and analog composite connectors.
No displays are superimposed.
0001
2L :
The remaining tape time is displayed on the
second line.
0006
50(SD) :
The 50 Hz system frequency is selected. However,
black signals are output from the HD SDI output
and analog component connectors.
0002
1L :
The remaining tape time is displayed on the first
line.
26*1
HD SYS H
ADV
For selecting the output whose HD output phase is to
be advanced by 90H in relation to the SD output.
0003
R/TTL :
The remaining tape time is displayed on the first
line and the total tape duration on the second line.
0000
0H
:
Both the HD and SD signals are output in phase
with the HD and SD REF output signals.
<Note>
The information will not be displayed when “2L” or “R/
TTL” is set and TIME is selected as the menu item
No.006 DISPLAY SEL setting.
0001
90H :
The HD signals are output at a phase advanced by
90H from the SD output signals.
005
SUPER
For setting the superimposing of the displays onto
various connectors.
When the SD REF signal is input, the REF input
and SD output are in-phase, and when the HD REF
signal is input, the REF input and HD output are
inphase.
0000
OFF :
The displays are superimposed onto none of the
output connectors.
<Notes>
0001
CMPST :
z The audio signals and TC signal are output in
phase with the HD output.
z With the 720p format, there is a phase difference of
120H between them.
The displays are superimposed onto the analog
composite output.
0002
CMPNT :
The displays are superimposed onto the HD
analog component output.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
0003
SDSDI :
The displays are superimposed onto SD SDI OUT.
0004
HDSDI :
The displays are superimposed onto HD SDI OUT.
0005
CPS&SD :
The displays are superimposed onto the analog
composite output and SD SDI OUT.
0006
CPN&HD :
The displays are superimposed onto the HD
analog component output and HD SDI OUT.
<Notes>
z The information will not be displayed when the
SUPER switch is OFF.
z 1394 output is according to Menu No. 899 DIF
SUPER.
z If the 23.98/24 Hz, 25 Hz (HD), or 50 Hz (HD)
mode is selected in menu No. 25 SYSTEM FREQ,
no super is displayed on the analog composite
output and the SD SDI output.
If the 25 Hz (SD) or 50 Hz (SD) mode is selected,
no super is displayed on the analog component
output and the HD SDI output.
“_____” indicates the factory setting.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
BASIC (continued)
No./Item
Description of setting
No./Item
Description of setting
006
DISPLAY
SEL
For setting what the information to be superimposed.
009
CHARA
TYPE
For setting the superimposed display and menu
display type.
0000
TIME :
Only the data is displayed.
(“Data” refers to the CTL, TC or UB value selected
by the COUNTER button.)
0000
WHITE
:
White characters are displayed on a black
background.
0001
T&STA :
0001
W/OUT :
The data and operation status are displayed.
White characters with black edges are displayed.
0002
T&S&M :
020*1
SYS FORMAT
For setting the format in which to record or play back
the signals including the HD REF signals.
The data, operation status and mode are
displayed.
0000
1080i
:
0003
T&RT :
1080i mode
The data and REC TIME are displayed.
0001
720p :
0004
T&YMD :
720p mode
The data and REC DATE (year/month/day) are
displayed.
022
PB FORMAT
For setting the format in which to play back the tape.
0000
MANUAL
:
0005
T&MDY :
The tape is played back in the format selected by
the menu item No.020 SYS FORMAT and No.023
FORMAT SEL setting.
The data and REC DATE (month/day/year) are
displayed.
0006
T&DMY :
0001
AUTO :
The data and REC DATE (day/month/year) are
displayed.
The tape is played back in the format selected by
the format in which the tape was recorded.
0007
T&UB :
The data and user bits are displayed. The time
code is displayed after the user bits when the
COUNTER button is set to UB.
023
FORMAT SEL
For selecting the format when “MANUAL” is selected
as the menu item No.022 PB FORMAT setting.
0000
HD_LP :
0008
T&CTL :
The DVCPRO HD-LP format is selected, and the
format follows the menu item No.020 SYS
FORMAT setting.
The data and CTL are displayed. The time code is
displayed after the CTL data when the COUNTER
button is set to CTL.
0001
HD_SP :
0009
T&T :
The DVCPRO HD format is selected, and the
format follows the menu item No.020 SYS
FORMAT setting.
The data and time code are displayed.
<Notes>
0002
422 :
z Depending on the format used, the following
displays appear for the modes.
The DVCPRO50 (422) format is selected.
0003
411 :
<Format>
DVCPRO HD-LP
DVCPRO HD
DVCPRO50
DVCPRO
DV
>
>
>
>
>
>
>
<Display>
DVCPRO_HD-LP
DVCPRO_HD
DVCPRO_50
DVCPRO
DV
DVCAM
The DVCPRO (411) format is selected.
0004
DV :
The DV format is selected.
0005
The DVCAM format is selected.
DVCAM :
DVCAM
z When T&S&M is selected as the item setting, an
error message is superimposed onto the display
when a warning or error occurs.
z REC TIME and REC DATE are displayed only
during DV or DVCAM playback. The operation
mode is displayed with the DVCPRO HD-LP,
DVCPRO HD, DVCPRO50 or DVCPRO format.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
<Note>
When the signal format to be output is set to other than
DVCPRO HD and an external device is connected to the DV
connector, the following settings are recommended.
z Menu No. 022 PB FORMAT:
MANUAL
z Menu No. 023 FORMAT SEL:
007
CHARA
H-POS
For setting the horizontal position at which the
superimposed characters are to be displayed.
0000
:
0
:
0006
:
0037
<Note>
6
:
37
Format of the tape that is inserted in the unit
Press the joystick and tilt up/down and right/left to set
the character position.
“_____” indicates the factory setting.
008
For setting the vertical position at which the
superimposed characters are to be displayed.
CHARA
V-POS
0000
:
0
:
0023
:
0032
<Note>
23
:
32
Press the joystick and tilt up/down and right/left to set
the character position.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
BASIC (continued)
Formats for playback
Depending on how the menu item No.020 SYS FORMAT,
No.022 PB FORMAT and No.023 FORMAL SEL settings are
combined, the formats of the tapes played back by the unit
differ as shown in the table below.
No./Item
Description of setting
For setting the field frequency.
030*1
HD
FREQUENCY
0000
59/23 :
The field frequency is set to 59.94/23.98 Hz.
0001
60/24 :
022.
PB FORMAT
020.
023.
Playback format
The field frequency is set to 60/24 Hz.
SYS FORMAT FORMAT SEL
<Note>
HD_LP
DVCPRO HD-LP (1080i)
DVCPRO HD (1080i)
DVCPRO50 (422)
DVCPRO (411)
DV
The field frequency which is set here takes effect only
when there is no input which supports the OUT REF
setting.
If there is an input which supports the setting, the
field frequency is consistent with the field frequency
of input.
HD_SP
50M
1080i
25M
DV
031*1
OUT REF
For selecting the video output reference.
DVCAM
HD_LP
HD_SP
DVCAM
MANUAL
0000
AUTO :
DVCPRO HD-LP (720p)
DVCPRO HD (720p)
DVCPRO50 (422)
DVCPRO (411)
DV
The REF signal (HD/SD) which is input to the REF
connector is automatically identified and serves as
the reference.
50M
720P
25M
If no signal is supplied to the REF connector, the
HD serial input signal serves as the reference.
If neither the REF input signal nor HD serial input
signal is supplied, the unit’s internal reference is
used.
DV
DVCAM
DVCAM
If AUTO is selected as the DVCPRO HD-LP
0001
INPUT :
menu item No.022 PB
FORMAT setting, the
format applying when the
format is not yet detected
(when the tape inserted)
follows the menu item
No.023 FORMAL SEL
setting.
(1080i/720p),
The input signal serves as the reference.
If this signal is not available, the unit’s internal
reference is used.
DVCPRO HD (1080i/
720p), DVCPRO50
(422), DVCPRO (411),
DVCPROP (420p), DC
or DVCAM format is
detected automatically.
0002
HD REF :
The HD REF input signal serves as the reference.
If this signal is not available, the unit’s internal
reference is used.
AUTO
0003
SD REF :
However, if “DV” or
The SD REF input signal serves as the reference.
If this signal is not available, the unit’s internal
reference is used.
“DVCAM” is selected,
operation proceeds as if
“HD_LP” is selected.
0004
E-AUTO :
When the editing mode is selected, the state is the
same as when set to “INPUT.”
When any mode other than the editing mode is
selected, the state is the same as when set to
“AUTO.”
<Notes>
z When the tape is ejected, the format follows the one
selected by menu item No.020 SYS FORMAT setting.
z DVCPRO P playback is not possible.
032*1
REC REF
Select the reference to synchronize the image frames
for recording.
0000
NORMAL
:
The video signal which is input is automatically
identified and serves as the reference.
0001
SLTC :
The time code which is input to the HD SDI IN
connector isidentified and serves as the reference.
<Note>
When the SLTC is selected, the following settings are
necessary to validate the settings for this item.
z Menu No. 25 SYSTEM FREQ: 59/60
z Menu No. 020 SYS FORMAT: 720p
z INPUT SELECT button on the front panel: HDSDI
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
“_____” indicates the factory setting.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
OPERATION
No./Item
Description of setting
No./Item
Description of setting
107*1
EE MODE
SEL
100
SEARCH
ENA
To set the transition method to search mode (stick
operation).
For setting the HD SDI and HD analog component
output signals in EE mode when HD SDI input is
selected.
0000
STICK :
Shift to the search mode when the SEARCH button
is pressed or when the stick is operated.
0000
NORMAL :
Signals delayed by the time taken by internal signal
processing are output.
0001
KEY :
Do not shift to the search mode unless the
SEARCH button is pressed.
0001
THRU :
Signal processing is not undertaken internally, and
the signals are output without delay at their original
timing.
101
SHTL MAX
For setting the maximum speed in the shuttle mode.
0000
X8.4 :
<Notes>
8.4k normal speed
z The superimposed information is not displayed
when THRU is used as the setting.
z When 1394 or SG is selected for the input signal in
edit mode, internal signal is selected forcibly
“NORMAL”.
0001
X16 :
16k normal speed
0002
X32 :
32k normal speed
<Note>
The maximum speed for the HD SP mode is
automatically limited to 25k normal speed.
108
PLAY DELAY
For setting the play rise time in frame increments.
0000
:
0
:
102
FF.REW MAX
For setting the maximum speed of fast forward or
rewind operations.
0015
15
109*1
CAP. LOCK
0000
X16 :
For selecting in how many field increments the
playback framing is to be locked.
16k normal speed
0001
X32 :
0000
0001
0002
2F
4F
8F
32k normal speed
0002
X50 :
50k normal speed
<Notes>
<Notes>
z “8F” can be selected only when “50i/25p” is
selected as the menu item No.25 SYSTEM FREQ
setting.
z In the HD LP or HD SP mode, 2F mode is selected
when recording and playing back, including editing,
regardless of the menu.
z The maximum speed for the HD SP mode is
automatically limited to 25k normal speed.
z The maximum speed for the DV and DVCAM
modes is automatically limited to 32k normal
speed.
104
REF ALARM
For setting whether a warning is to be displayed when
the REF VIDEO signal is not connected.
110
AUTO REW
For setting whether the tape is to be automatically
rewound to its beginning when the tape end is detected.
0000
OFF :
0000
OFF :
No warning is displayed.
The tape is not rewound.
0001
ON :
0001
ON :
A warning is displayed by the flashing STOP lamp.
The tape is rewound to its beginning.
105*1
AUTO EE
SEL
For setting the mode of the VTR, which becomes the
EE state when menu item No. 140 OUTPUT is set to
“EE.”
112
FRZ MODE
SEL
For setting the video output when the mode is
transferred from playback images to standby OFF
(half loading) mode or EJECT mode.
0000
S/F/R :
0000
DIS :
The mode changes to the EE state when this item
is set to STOP, FF, or REW.
The video output is muted.
0001
STBOFF :
0001
STOP :
When the standby OFF (half loading) mode is
established, the image played back at that moment
is frozen and output.
The mode changes to the EE state only when this
is set to STOP.
0002
SOF&EJ :
106
EJECT EE
SEL
For setting the output conditions of video images and
voice when ejecting the tape.
When in the STANDBY OFF mode and the EJECT
mode, the image played back at that moment is
frozen and output.
0000
EE :
Both the video and audio signals are always output
in the EE (electric modulation to electric playback)
mode regardless of the setting of the menu No.140
OUTPUT.
<Notes>
z The frozen status will be according to the settings
in menu No. 604 FREEZE SEL.
z In the EJECT mode, the frozen image will be
output only when setup No. 106 EJECT EE is the 1
(BLACK) or 2 (GRAY) setting.
0001
BLACK :
The output status differs according to the setting of
the menu No.140 OUTPUT.
EE:
The signals are output in the EE mode.
114
REC INH
LAMP
For setting the operation of the REC INHIBIT lamp when
the cassette is set to the erasure prevention status.
TAPE: BLACK is output for the video, and the
audio is muted.
0000
LIGHT :
0002
GRAY :
The lamp lights.
The output status differs according to the setting of
the menu No.140 OUTPUT.
0001
FLASH :
The lamp flashes.
<Note>
When the REC INHIBIT switch on the front panel is set
to ON, the REC INHIBIT lamp lights at all times
regardless of what setting is selected for this menu item.
EE:
The signals are output in the EE mode.
TAPE: GRAY is output for the video, and the audio
is muted.
<Note>
When “23/24” mode, “25 (HD/SD)” mode, or “50 (HD/
SD)” mode is selected in menu No. 25 SYSTEM
FREQ, BLACK is output if “EE” is selected.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
“_____” indicates the factory setting.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
OPERATION (continued)
No./Item
Description of setting
No./Item
Description of setting
115*1
EJECT SW
INH
For setting whether to restrict the operation of the
EJECT button on the front panel.
152
HUMID OPE
For setting the unit’s operation when condensation
has formed.
0000
REC :
0000
OFF :
Operation is inhibited while the unit is in the
recording mode.
The unit does not operate when condensation has
formed.
0001
OFF :
0001
ON :
The EJECT button can be operated in all operation
modes.
It operates even when condensation has formed
but no guarantees are made that the operation will
be trouble-free.
118*1
SP MODE
INH
For selecting whether to enable or disable recording
on a tape which has been recorded using a format
other than DVCPRO HD-LP.
<Note>
Since operating the unit when condensation has
formed may damage the tape or give rise to other
trouble, the “OFF” setting is recommended under
normal circumstances.
0000
OFF :
Recording onto the cassette tape is enabled.
0001
ON :
Recording onto the cassette tape is disabled.
154*1
AUTO BACK
For setting how the follow-on recording function is to
be used.
(For setting the AUTO BACK function operation which
rewinds the tape for several seconds in order to
ensure that the video images follow on one from
another with no disruptions.)
119*1
CONFI REC
For selecting whether or not to perform simultaneous
playback during normal recording (Other than the
frame-by-frame shooting).
0000
OFF :
The output for simultaneous playback during
normal recoding is switched in accordance with the
menu item No.140 OUTPUT.
0000
OFF :
The tape is not rewound automatically (no AUTO
BACK).
EE:
EE output
0001
REC-P :
TAPE: Simultaneous playback output
The tape is rewound (AUTO BACK) during REC
PAUSE, and it then stops in the recording standby
status. (When PAUSE is released, the tape runs
up, and recording starts.)
0001
ON :
Simultaneous playback during normal recoding is
performed at all times, regardless of the setting of
the menu item No.140 OUTPUT.
0002
ALL :
134
ALARM
BEEP
For selecting the alarm sound for condensation,
termination of the tape (remaining time of about 2
minutes) or running out of battery power.
In addition to the function of the 0001 REC-P
setting, the tape is rewound (AUTO BACK) during
REC PLAY, the tape immediately runs up, and
recording starts.
0000
OFF :
The alarm sound is not activated.
0001
ON :
The alarm sound is activated.
<Note>
If "ON" is selected in menu item No. 152 HUMID
OPE, the alarm sound for condensation is not
activated even if "ON" is selected.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
“_____” indicates the factory setting.
140*1
OUTPUT
For selecting the output signals.
0000
EE :
<In the STOP mode>:
The input signals selected by the setting of the
INPUT SELECT button are output.
<During recording or editing>:
The input signals selected by the setting of the
INPUT SELECT button are output:
0001
TAPE :
<In the STOP mode>
The signals played back from the tape are output.
<During recording or editing>:
The simultaneous playback signals are output.
<Note>
In order to select the output signals during recording
or editing, set menu item No.119 CONFI REC or
No.302 CONFI EDIT.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
OPERATION (continued)
No./Item
Description of setting
No./Item
Description of setting
155*1
AUTO REC
For setting whether the recording/stop is executed
automatically in conjunction with the Recording Mark
of the HD SDI input signals from our camera recorder
or not.
160
MEMORY
MODE
For setting the repeat playback mode.
0000
OFF :
No repeat playback (normal operation).
0001
M-STOP :
0000
OFF :
The tape stops near the BEGIN point when it is fast
forwarded or rewound.
Do not to execute the recording/stop automatically.
0001
TYPE1 :
0002
REPT1 :
To execute the recording/stop automatically in
conjunction with the Recording Mark in the LTC
information added to the HD SDI.
When the tape reaches the END point, it is
rewound to the BEGIN point, and stops.
0003
CONT :
0002
TYPE2 :
When the tape reaches the END point, it is
rewound to the BEGIN point, and plays back, and
this is done repeatedly.
To execute the recording/stop automatically in
conjunction with the Recording Mark in the SVITC
information added to the HD SDI.
161
CTL BGN
or
For setting the BEGIN point in the repeat playback
mode.
Either TC or CTL is set as the counter display mode
using the COUNTER button.
If no mode is set, – – : – – : – – : – – appears, and the
tape start serves as the BEGIN point.
<Notes>
z Set the LOCAL/REMOTE switch to the REMOTE
position.
z For the selection of TYPE 1 or TYPE 2, refer to
“Our camera recorder, Recording format, and
Recording Mark.”
z To select TYPE 1 or TYPE 2 to start recording
automatically, set this unit to the REC PAUSE
mode. It may not operate in any mode other than
the REC PAUSE mode. After accepting the auto
stop, this unit changes to the REC PAUSE mode.
z When this unit is recording in normal operation, the
AUTO REC function is not available.
TC BGN
162
END
For setting the END point in the repeat playback mode.
Either TC or CTL is set as the counter display mode
using the COUNTER button.
If no mode is set, – – : – – : – – : – – appears, and the
tape end serves as the END point.
163
REPT MODE
For setting what images are to be output while the
tape returns to the BEGIN point in the repeat
playback mode.
0000
FREEZE :
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
The tape returns to the BEGIN point with the image
played back at the END point still frozen.
0001
BLACK :
The tape returns to the BEGIN point while the
screen remains black.
Our camera recorder, Recording format, and Recording Mark
0002
MENU :
Recording
Mark TYPE
The tape returns to the BEGIN point following the
the settings in menu No. 140 OUTPUT.
<Note>
If the tape end is set as the END point when
“FREEZE” is selected, the playback image will not be
frozen properly.
Model
Recording format
Remarks
AJ-HDC27F, H
AJ-HDX400
720/¢¢p over 60p
TYPE1
ー
2
1080/59.94i
–*
Set the END point to a place within the range where
images are recorded.
2
1080/50i
–*
It is possible to
switch between
TYPE 1 and
TYPE 2. TYPE-1
and TYPE-2 are
the initial
settings for the
camera recorder.
If the unit is used
with the TYPE-1
settings, set the
UB MODE of the
camera to “FRM
RATE”. If it is
used with the
TYPE-2 settings,
set the VITC UB
MODE to “FRM
RATE.”
AJ-HDX400E
180
BATTERY
SEL
For setting the type of battery.
2
1080/25p over 50i
–*
0000
NiCd12 :
Settings for 1 pc. 12 V battery (NEAR: 11.2 V,
END: 10.6 V)
720/59.94p
TYPE1
TYPE1
TYPE1
0001
NiCd13 :
720/23.98p over 59.94p
720/29.97p over 59.94p
Settings for 1 pc. 13 V battery (NEAR: 12.0 V,
END: 10.6 V)
0002
NiCd14 :
2
1080/59.94i
–*
Settings for 1 pc. 14 V battery (NEAR: 13.6 V,
END: 10.6 V)
1080/23.98p over 59.94i
1080/29.97p over 59.94i
TYPE2
0003
S-LION :
AJ-HDX900
Settings for 1 pc. lithium-ion battery “BP-L90A”.
(NEAR: 11.7 V, END: 10.6 V)
2
–*
0004
I-LION :
2
1080/50i
–*
Settings for 1 pc. lithium-ion battery “ENDURA80”.
(NEAR: 12.9 V, END: 12.4 V)
2
1080/25p over 50i
720/50p
–*
0005
TYPE-A :
Setting for using the battery selected by the menu
item No.181 TYPE-A NEAR item and No.182
TYPE-A END item
TYPE1
TYPE1
720/25p over 50p
0006
TYPE-B :
Setting for using the battery selected by the menu
item No.183 TYPE-B NEAR item and No.184
TYPE-B END item
*2 In the initial settings, the Recording Mark is not
overlapped on the HD SDI signals.
“_____” indicates the factory setting.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
OPERATION (continued)
No./Item
Description of setting
No./Item
Description of setting
181*1
TYPE-A
NEAR
191*2
A IN SEL INH
For setting (in increments of 0.1 V) the voltage level at
which the counter flashes as warning for TYPE-A
battery (selected as the menu item No.180 BATTERY
SEL item).
Use when adjusting the settings for multiple batteries
or new type batteries.
Select the audio input switching mode with the INPUT
SELECT switch.
0000
OFF :
Select the audio input switching mode with the
INPUT SELECT switch.
0001
ON :
0000
:
10.6
:
Video input switching with the INPUT SELECT
switch is prohibited.
0023
:
0044
<Note>
12.9
:
15.0
0002
REC :
After this unit shifts to recording (except editing),
video input switching with the INPUT SELECT
switch is prohibited.
When this item has been set to a voltage level close
to 15.0 V, the counter display may flash even when an
AC power source is being used.
*1 Even if the RESET button is pressed while pressing the
SEARCH button, the value may not return to the factory
setting.
*2 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
182*1
TYPE-A END
For setting (in increments of 0.1 V) the voltage level at
which the TYPE-A battery (selected as the menu item
No.180 BATTERY SEL item) is to be automatically
turned off.
Use when adjusting the settings for multiple batteries
or new type batteries.
0000
:
10.6
:
0018
:
0034
12.4
:
14.0
INTERFACE
No./Item
Description of setting
183*1
TYPE-B
NEAR
For setting (in increments of 0.1 V) the voltage level at
which the counter flashes as warning for TYPE-B
battery (selected as the menu item No.180 BATTERY
SEL item).
Use when adjusting the settings for multiple batteries
or new type batteries.
202
ID SEL
For setting the ID information to be returned to the
controller.
0000
OTHER :
The ID information of the VTR other than DVCPRO
is set.
DVCPRO :
The DVCPRO ID information is set.
0000
:
10.6
:
0001
0023
:
0044
<Note>
12.9
:
15.0
0002
ORIG :
Set this only when the unit is connected to a
Panasonic controller (such as the AG-A850,
optional accessory).
When this item has been set to a voltage level close
to 15.0 V, the counter display may flash even when an
AC power source is being used.
<Note>
Select 1 (DVCPRO) or 2 (ORIG) if “23/24,” “25(HD),”
“25(SD),” “50(HD)” or “50(SD)” is selected as the
menu item No.25 SYSTEM FREQ setting.
184*1
TYPE-B END
For setting (in increments of 0.1 V) the voltage level at
which the TYPE-B battery (selected as the menu item
No.180 BATTERY SEL item) is to be automatically
turned off.
“_____” indicates the factory setting.
0000
:
10.6
:
0018
:
0034
12.4
:
14.0
190*2
V IN SEL INH
For selection of the video input switching mode with
the INPUT SELECT switch.
0000
OFF :
Video input switching with the INPUT SELECT
switch is enabled.
0001
ON :
Video input switching with the INPUT SELECT
switch is prohibited.
0002
REC :
After this unit shifts to recording (except editing),
video input switching with the INPUT SELECT
switch is prohibited.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
EDIT
No./Item
Description of setting
No./Item
Description of setting
302*1
CONFI EDIT
323*1
EDIT
RPLCE4
For selecting whether to perform simultaneous
playback during editing.
As with menu item No.320, the VTR’s CH4 edit
presets are set to ON or OFF following the analog
audio signals specified by the controller.
0000
OFF :
Simultaneous playback is not performed.
0000
N-DEF :
0001
ON :
Not set.
0001
Simultaneous playback is performed.
CH1 :
The analog CH1 edit presets are followed.
303*1
AUD EDIT IN
For selecting how to connect the digital audio edit IN
points.
0002
CH2 :
The analog CH2 edit presets are followed.
0000
CUT :
0003
CH1+2 :
Cut processing
The analog CH1 or CH2 edit presets are followed.
0001
FADE :
324*1
EDIT
RPLCEC
V-fade processing
As with menu item No.320, the VTR’s CUE edit
presets are set to ON or OFF following the analog
audio signals specified by the controller.
304*1
AUD EDIT
OUT
For selecting how to connect the digital audio edit
OUT points.
0000
N-DEF :
0000
CUT :
Not set.
0001
Cut processing
CH1 :
0001
FADE :
The analog CH1 edit presets are followed.
V-fade processing
0002
CH2 :
307*1
AFTER CUE-
UP
For selecting the VTR’s mode upon completion of the
cue-up operation.
The analog CH2 edit presets are followed.
0003
CH1+2 :
0000
STOP :
The analog CH1 or CH2 edit presets are followed.
The VTR is set to the STOP mode.
0001
STILL :
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
The VTR is set to the still picture (SHTL STILL)
mode.
0002
STILL2 :
The VTR is set to the still picture (VAR STILL)
mode.
“_____” indicates the factory setting.
320*1
EDIT
RPLCE1
For setting the allocation of the channels for the
analog audio presets of a controller when a controller
without a function to control the edit presets of the
digital audio signals is used to edit the digital audio
signals of the VTR.
The VTR’s CH1 edit presets are set to ON or OFF
following the analog audio signals specified by the
controller.
0000
N-DEF :
Not set.
0001
CH1 :
The analog CH1 edit presets are followed.
0002
CH2 :
The analog CH2 edit presets are followed.
0003
CH1+2 :
The analog CH1 or CH2 edit presets are followed.
321*1
EDIT
RPLCE2
As with menu item No.320, the VTR’s CH2 edit
presets are set to ON or OFF following the analog
audio signals specified by the controller.
0000
N-DEF :
Not set.
0001
CH1 :
The analog CH1 edit presets are followed.
0002
CH2 :
The analog CH2 edit presets are followed.
0003
CH1+2 :
The analog CH1 or CH2 edit presets are followed.
322*1
EDIT
RPLCE3
As with menu item No.320, the VTR’s CH3 edit
presets are set to ON or OFF following the analog
audio signals specified by the controller.
0000
N-DEF :
Not set.
0001
CH1 :
The analog CH1 edit presets are followed.
0002
CH2 :
The analog CH2 edit presets are followed.
0003
CH1+2 :
The analog CH1 or CH2 edit presets are followed.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
TAPE PROTECT
TIME CODE
No./Item
Description of setting
No./Item
Description of setting
500*1
VITC BLANK
400
STILL TIMER
For setting the time to be taken before the unit is set
in the tape protection mode when it is left standing in
the STOP or STILL status.
For setting whether to output the VITC signal at the
position which is set using menu items No.501 VITC
POS-1 and No.502 VITC POS-2.
(Units: S = seconds, min = minutes)
0000
BLANK :
0000
0001
0002
0003
0004
0005
0006
0007
0008
<Note>
0.5S
5S
The VITC signal is not output.
0001
The VITC signal is output.
<Note>
This setting takes effect only with the SD output
(analog composite output and SD SDI output).
THRU :
10S
20S
30S
40S
50S
1min
2min
501*1*2
VITC POS-1
For setting the position where the VITC signal is to be
inserted.
<525 mode>
0000
:
0006
:
0010
<625 mode>
0000
:
0004
:
0015
10L
:
16L
:
7L
:
11L
:
When a DV, DVCAM or an unused tape is used, or a
DVCPRO HD/DVCPRO50/DVCPRO tape is used in
the EE mode, any setting above 2 (10S) will result in
a setting time of 10 seconds.
20L
22L
401
SRC
PROTECT
For setting the operation to be performed in the tape
protection mode when the unit is left standing in the
STILL status (JOG/VAR/SHTL).
<Notes>
z The same line as the one selected by menu item
No.502 VITC POS-2 and No.692 UMID POS
cannot be selected.
z This setting takes effect only with the SD output
(analog composite output and SD SDI output).
0000
STEP :
STEP FWD
0001
HALF :
STANDBY OFF (HALF LOADING)
<Note>
When STEP FWD is selected, the unit is
automatically transferred to the standby OFF (half
loading) mode when the unit is left standing in the
STOP mode for a total of 30 minutes (or 1 minute for
DV or DVCAM tape).
502*1*2
VITC POS-2
For setting the position where the VITC signal is to be
inserted.
<525 mode>
0000
:
0008
:
<625 mode>
0000
:
0008
:
10L
:
18L
:
7L
:
13L
:
402
DRUM
STDBY
For setting the cylinder operation in the standby OFF
(half loading) mode.
0010
<Notes>
20L
0015
22L
0000
OFF
z The same line as the one selected by menu item
No.501 VITC POS-1 and No.692 UMID POS
cannot be selected.
z This setting takes effect only with the SD output
(analog composite output and SD SDI output).
The cylinder stops rotating.
0001
ON
The cylinder continues to rotate.
403
STOP
PROTECT
For setting the operation to be performed in the tape
protection mode when the unit is left standing in the
STOP status.
503*1
TCG MODE
For setting the synchronization of the internal time
code generator.
0000
STEP :
0000
SW :
STEP FWD
When the TCG switch on the front panel is set to
REGEN or PRESET, the selection is complied.
0001
HALF :
STANDBY OFF (HALF LOADING)
<Note>
0001
AUTO :
REGEN or PRE is automatically selected
depending on the operation mode.
When editing (including a chained shot):
REGEN is selected.
When STEP FWD is selected, the unit is
automatically transferred to the standby OFF (half
loading) mode when the unit is left standing in the
STOP mode for a total of 30 minutes (or 1 minute
for DV or DVCAM tape).
Other than the above: PRE is selected.
504*1
RUN MODE
For setting the operation mode in which the internal
time code generator runs.
0000
REC :
“_____” indicates the factory setting.
The generator runs only while recording is in
progress.
0001
FREE :
The generator runs while the power is on
regardless of the unit’s operation mode.
505*1
TCG REGEN
For setting the signal to be regenerated when the
TCG (time code generator) is in the regeneration
mode.
0000
TC&UB :
Both the time code and user bits are regenerated.
0001
TC :
Only the time code is regenerated.
0002
UB :
Only the user bits is regenerated.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
*2 Even if the RESET button is pressed while pressing the
SEARCH button, the value may not return to the factory
setting.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
TIME CODE (continued)
No./Item
Description of setting
No./Item
Description of setting
506*1
REGEN
MODE
511*1
DF MODE
For selecting the editing mode range when the VTR is
operating in the REGEN mode while performing
editing operations with “AUTO” selected as the menu
item No.503 TCG MODE setting.
For selecting whether to use the DF or NDF mode for
CTL and TCG.
0000
DF :
The drop frame (DF) mode is used.
0000
AS&IN :
0001
NDF :
Regeneration applies during assemble or insert
editing.
The non-drop frame (NDF) mode is used.
512*1
TC OUT REF
When the TCG switch of the front panel is set to EXT,
it switches the phase of time code output from the TC
OUT connector for external LTC input. (In EE mode
only)
0001
ASSEM :
Regeneration applies during assemble editing.
0002
INSRT :
Regeneration applies during insert editing.
0000
VOUT :
<Note>
Match the output image.
At the time of frame-by-frame shooting, the
operations are equivalent to assemble editing.
0001
TC_IN :
Match the external time code input.
507*1
EXT TC SEL
513
VITC OUT
For selecting how to output the VITC signal which is
superimposed onto the output video signal.
For selecting the time code to be used when an
external time code is used.
0000
EXT_L :
0000
SBC :
The LTC information of the TIME CODE IN
connector is used.
In the playback mode, the time code recorded in
the SBC area* is output.
A
0001
SLTC :
0001
VAUX :
The LTC information added to the serial signals
which are supplied to the HD SDI IN connector is
used.
In the playback mode, the time code recorded in
the VAUX area* is output.
B
<Notes>
0002
SVITC :
z The VITC information which is detected by the HD
serial input is automatically recorded in the VAUX
area when the images are recorded.
z When “23/24,” “25(HD),” “25(SD),” “50(HD)” or
“50(SD)” is selected as the menu item No.25
SYSTEM FREQ setting and VAUX is selected as
the VITC OUT setting, the time code which is
output may not be continuous.
The VITC information added to the serial signals
which are supplied to the HD SDI IN connector is
used.
<Note>
When selecting “1394” with the INPUT VIDEO switch
on the front panel, the time code input to IEEE1394
digital input/output connector is used.
The VITC information will not be superimposed onto
the video signal output when recording is performed
or the EE mode is established. The LTC information
and VITC information are not superimposed onto the
HD serial output signals.
514*1
HD EMBD
VITC
For selecting whether to superimpose the VITC
information onto the HD serial output.
0000
OFF :
The VITC information is not superimposed.
0001
ON :
508*1
BINARY GP
The VITC information is superimposed.
For setting the usage status for the user bits of the
time code generated by the TCG.
515*1
HD EMBD
LTC
For selecting whether to superimpose the LTC
information onto the HD serial output.
0000
000 :
No character set specified
0000
OFF :
0001
001 :
The LTC information is not superimposed.
8-bit character set complying with the ISO646 and
ISO2022 standards
0001
ON :
The LTC information is superimposed.
0002
Undefined
0003
Undefined
0004
Undefined
0005
Page/line
010 :
011 :
100 :
101 :
110 :
111 :
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
*A The SBC (Sub Code Data) area is an area that exists
separately from the video and audio area on the helical
track and contains the tape management information,
such as the time code, in compliance with the SMPTE/
EBU and the recording time. As with the ordinary LTC
(Linear Time Code), the time code can be read even
when rewinding/fast-forwarding and can be read out
when the tape stops.
0006
Undefined
0007
Undefined
509
PHASE
CORR
For setting whether to control the phase correction of
the LTC output during playback.
0000
OFF :
The phase correction is not controlled.
0001
ON :
*B The VAUX (Video Auxiliary Data) area is an area in the
video area on the helical track and contains information
related to the video data.
The phase correction is controlled.
510*1
For selecting whether to set the CF flag of the TCG to
ON.
TCG CF
FLAG
0000
OFF :
The CF flag is set to OFF.
0001
“_____” indicates the factory setting.
ON :
The CF flag is set to ON.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
VIDEO
No./Item
Description of setting
No./Item
Description of setting
601*1
VIDEO INT
SG
621*1
UPCONV
MODE
For selecting the type of internal standard signals.
For setting the image processing during up-
conversion.
0000
100%CB :
A 100% color bar signal is selected.
0000
FIT_V :
0001
75%CB :
Side panel mode
A 75% color bar signal is selected.
0001
FIT_H :
0002
SMPTE :
Top and bottom cut-off in vertical direction
An SMPTE color bar signal is selected.
0002
Stretch mode
FIT_HV :
0003
ARIB :
An ARIB color bar signal is selected.
626*1
D/C ENH H
For enhancing the horizontal outlines during down-
conversion.
0004
BLACK :
A black signal is selected.
0000
0dB
602*1
SDI IN MODE
For selecting how to process the serial input.
0001
+1dB
0000
DR_OFF :
627*1
D/C ENH V
For enhancing the vertical outlines during down-
conversion.
0000
The 8 higher bits whose two lower bits have been
rounded off are recorded.
0dB
+1dB
0001
DR_ON :
0001
The dynamically rounded 8 higher bit signal is
recorded.
For setting whether to mute the video output signal
when a blank part of the tape is detected during
playback.
628*1
U/C ENH H
For enhancing the horizontal outlines during up-
conversion.
0000
603
V-MUTE SEL
0dB
+1dB
0001
629*1
U/C ENH V
For enhancing the vertical outlines during up-
conversion.
0000
0000
N-MUTE :
The video output signal is not muted. (It is frozen.)
0dB
+1dB
0001
GRAY :
0001
The video output signal is muted and turned gray.
630*1
1080i
HD_OUT
For selecting the HD output signal format during
1080i tape playback or in the 1080i EE mode.
0000
0001
<Note>
0002
BLACK :
The video output signal is muted and turned black.
>
1080i
720p
0003
NOISE :
The video output signal is muted and turned into
noise.
This item’s setting cannot be changed while a tape is
being recorded or while the recording pause mode is
established.
604
FREEZE SEL
For selecting the freeze mode of the still pictures and
the slow play mode.
0000
FIELD :
632*1
Field freeze, field slow
For selecting the HD output signal format during 720p
tape playback or in the 720p EE mode.
0001
FRAME :
720p
>
Frame freeze, frame slow
<Note>
0000
0001
1080i
720p
HD_OUT
<Note>
For IEEE 1394 digital output, if format conversion is
not executed, the frames may freeze or slow down
regardless of the settings in this item.
This item’s setting cannot be changed while a tape is
being recorded or while the recording pause mode is
established.
615*1
V OUT SEL
For selecting what signals are to be output from the
VIDEO OUT1 output connector.
636*1
For selecting the HD output signal format during SD
tape (DVCPRO50, DVCPRO, DV or DVCAM)
playback.
0000
CMPNT :
SD
>
The HD component signals are output.
HD_OUT
0001
CMPST :
0000
1080i
Composite signals are output.
0001
720p
<Note>
650
STYLE
0000
CMPNT :
When the CMPST is selected, the Pb and Pr of the
analog HD component signals are muted.
Level adjustment mode for the component style
0001
CMPST :
619*1
V_FILTER
Level adjustment mode for the composite style
This is used to select the method to process the
images using the vertical filter during down-
conversion.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
0000
FIELD :
The images are processed by field basis.
0001
FRAME :
The images are processed by frame basis.
<Note>
“_____” indicates the factory setting.
When “FRAME” has been selected, the resolution is
improved, but the images may flicker.
620*1
DOWNCON
MODE
For setting the image processing during down-
conversion.
0000
FIT_V :
Side cut mode
0001
FIT_H :
Letter-box mode
0002
FIT_HV :
Squeeze mode
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
VIDEO (continued)
No./Item
Description of setting
No./Item
Description of setting
651*1
HUE STYLE
(SD)*DW
For setting the axis of revolution for the chroma phase
adjustment of the SD SDI output and analog
composite output.
660
Pr LVL
(SD)*DW
For adjusting the PR level of the SD SDI output and
analog composite output. (–
to 0 dB to +3 dB)
0000
:
0.0%
:
0000
Pb-Pr :
The axis rotates in a perfect circle on the SDI
(component style) vectorscope.
1000
:
1413
<Note>
100.0%
:
141.3%
0001
U-V :
The axis rotates in a perfect circle on the analog
(composite style) vectorscope.
This setting takes effect when “CMPNT” has been
selected as the menu item No.650 setting.
653
Y LVL
(HD)*UP
For adjusting the Y level of the HD SDI or HD analog
component output.
661
BK LVL
(SD)*DW
For adjusting the black level of the SD SDI output and
analog composite output.
(–
to 0 dB to +3 dB)
0000
:
0.0%
:
50
–10.0%
:
:
1000
:
1413
100.0%
:
141.3%
150
:
0.0%
:
250
+10.0%
<Note>
<Note>
This setting takes effect when “CMPNT” has been
selected as the menu item No.650 setting.
This setting takes effect when “CMPNT” has been
selected as the menu item No.650 setting.
654
Pb LVL
(HD)*UP
For adjusting the PB level of the HD SD or HD analog
componentI output.
662
V LEVEL
For adjusting the video level of the HD SDI, analog
component output, SD SDI output and analog
(–
to 0 dB to +3 dB)
composite output. (–
to 0 dB to +3 dB)
0000
:
0.0%
:
0000
:
0.0%
:
1000
:
1413
100.0%
:
141.3%
1000
:
2000
<Note>
100.0%
:
200.0%
<Note>
This setting takes effect when “CMPNT” has been
selected as the menu item No.650 setting.
This setting takes effect when “CMPST” has been
selected as the menu item No.650 setting.
655
Pr LVL
(HD)*UP
For adjusting the PB level of the HD SDI or HD
663
C LEVEL
For adjusting the chroma level of the HD SDI, analog
component output, SD SDI output and analog
analog component output. (–
to 0 dB to +3 dB)
0000
:
0.0%
:
composite output. (–
to 0 dB to +3 dB)
0000
0.0%
1000
:
1413
<Note>
100.0%
:
141.3%
:
:
1000
:
1413
<Note>
100.0%
:
141.3%
This setting takes effect when “CMPNT” has been
selected as the menu item No.650 setting.
This setting takes effect when “CMPST” has been
selected as the menu item No.650 setting.
656
BK LVL
(HD)*UP
For adjusting the black level of the HD SDI or HD
analog component output.
664
HUE
(AJ-HD1400P)
For adjusting the chroma phase of the HD SDI,
analog component output, SD SDI output and analog
composite output. (Approx. –30 o to +30 o)
0000
:
0062
:
50
–10.0%
:
:
0.0%
:
150
:
250
<Note>
–31.0
:
C PHASE
(AJ-HD1400E)
+10.0%
0.0
:
0124
<Notes>
31.0
This setting takes effect when “CMPNT” has been
selected as the menu item No.650 setting.
z This setting takes effect when “CMPST” has been
selected as the menu item No.650 setting.
z If 50 Hz mode or 25 Hz mode has been selected as
the system menu item No.25 SYSTEM FREQ
setting:
• The HD SDI output cannot be adjusted.
• The SD SDI output and VIDEO output can be
adjusted only when an SD format tape is being
played back or when cross-convert has been
658
Y LVL
(SD)*DW
For adjusting the Y level of the SD SDI output and
analog composite output. (–
to 0 dB to +3 dB)
0000
:
0.0%
:
1000
:
1413
<Note>
100.0%
:
141.3%
This setting takes effect when “CMPNT” has been
selected as the menu item No.650 setting.
selected
in
the
menu
item
No.630
1080i>HD_OUT and No.631 720p>HD_OUT.
659
For adjusting the PB level of the SD SDI output and
Pb LVL
(SD)*DW
analog composite output. (–
to 0 dB to +3 dB)
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
0000
:
0.0%
:
1000
:
100.0%
:
1413
<Note>
141.3%
*UP: With HD output (HD tape playback or up-converted
output)
This setting takes effect when “CMPNT” has been
selected as the menu item No.650 setting.
*DW: With SD output (SD tape playback or down-converted
output)
“_____” indicates the factory setting.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
VIDEO (continued)
No./Item
Description of setting
No./Item
Description of setting
686*1
CCR MODE
(SD)*DW
665
SETUP LVL
(AJ-HD1400P)
For adjusting the setup ( or black) level of the HD SDI,
analog component output, SD SDI output and analog
composite output. (–10 o to +10 o)
For selecting the cross color processing during
playback.
0000
OFF :
50
–10%
The cross color is output as is.
:
:
0.0%
:
0001
ON :
BK LVL
(AJ-HD1400E)
150
:
250
<Note>
The cross color can be reduced.
687*1
SDI INDEX
0*DW
For selecting whether to superimpose the VIDEO
INDEX signal on the SD SDI output signal.
+10.0%
0000
OFF :
This setting takes effect when “CMPST” has been
selected as the menu item No.650 setting.
The VIDEO INDEX signal is not superimposed on
the SD SDI output signal.
0001
ON :
676*1
BLK CLIP
For setting whether to clip what is below the pedestal
level for the Y (luminance) signal of composite output
and SD SDI output.
The VIDEO INDEX signal is superimposed on the
SD SDI output signal.
0000
OFF :
689*1
COMP MODE
This is used to select the method to process the
image compression during recording.
What is below the pedestal level is not clipped.
0001
ON :
0000
NORMAL :
What is below the pedestal level is clipped.
The images are recorded using the regular
compression processing.
680*1
For selecting ON or OFF for the closed caption signal
in the first field.
0001
DARK :
CC (F1)
BLANK*DW
The images are recorded while minimizing the
compressed image distortion which arises in the
dark areas below about 10 IRE (70 mV).
0000
Forced blanking
0001
No blanking
BLANK :
THRU :
<Notes>
z This setting is valid when recording in the 720p
mode.
z When “DARK” has been selected, the COMP lamp
lights.
681*1
CC (F2)
BLANK*DW
For selecting ON or OFF for the closed caption signal
in the second field.
0000
BLANK :
Forced blanking
690*1
UMID REC
0001
THRU :
This selects whether or not to record the UMID
information on the tape.
No blanking
0000
OFF :
682*1
VO SETUP
(HD)*UP
(AJ-HD1400P)
This selects the composite output signal in HD mode.
UMID information is not recorded on the tape.
0000
THRU :
0001
ON :
The signal is output with no setup added.
The UMID set in menu No. 691 UMID GEN is
recorded. If no Basic UMID is available in the input
signals, a Basic UMID of the unit, which is newly
generated, is recorded.
0001
ADD22L :
The signal is output from line 22 with a 7.5% setup
added.
0002
ADD21L :
<Note>
The signal is output from line 21 with a 7.5% setup
added.
UMID information cannot be rewritten in this unit.
691*1
UMID GEN
0003
ADD20L :
This selects a UMID that is recorded when menu No.
690 UMID REC is turned “ON”.
The signal is output from line 20 with a 7.5% setup
added.
0000
INT :
Newly created basic UMID information of this unit
is always recorded.
683*1
VO SETUP
(SD)*DW
(AJ-HD1400P)
This selects the composite output signal in SD mode.
0000
THRU :
0001
EXT :
The signal is output with no setup added.
The UMID information of the input signals is
recorded. If no UMID is available in the input
signals, a Basic UMID of the unit, which is newly
generated, is recorded.
0001
ADD22L :
The signal is output from line 22 with a 7.5% setup
added.
0002
ADD21L :
<Note>
The signal is output from line 21 with a 7.5% setup
added.
The source pack (of the UMID information) of the
input signal will be recorded on the tape, regardless
of this menu’s setting.
00023
ADD20L :
The signal is output from line 20 with a 7.5% setup
added.
684*1
EDH (SD)*DW
For setting whether to superimpose EDH onto the SD
SDI output.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
0000
OFF :
EDH is not superimposed.
0001
ON :
EDH is superimposed.
*UP: With HD output (HD tape playback or up-converted
685*1
ESR MODE
(SD)*DW
output)
For selecting the mode of the edge subcarrier
reduction (ESR) operation in the playback circuit.
*DW: With SD output (SD tape playback or down-converted
output)
0000
OFF :
ESR is forcibly turned off.
0001
AUTO :
“_____” indicates the factory setting.
ESR is automatically set to ON or OFF depending
on the unitÅfs operation.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
VIDEO (continued)
No./Item
Description of setting
No./Item
Description of setting
692*1
UMID POS
695*1
BLANK
LINE*DW
This sets the line on which the UMID information is to
be superimposed.
For selecting the blanking ON/OFF for a period of
vertical blanking on video signals of the SD output.
0000
BLANK
0000
BLANK :
0001
12L
:
All the lines are forcibly blanked.
:
0001
THRU :
0006
:
17L
:
None of the lines are blanked.
0002
MANU :
0008
<Notes>
19L
Blanking ON or OFF is selected on a line-byline
basis.
<Notes>
z The line selected for the menu item No. 501 VITC
POS-1 and No. 502 VITC POS-2 settings cannot
be selected for this item.
z The default settings are not restored even if the
RESET button is pressed while holding down the
SEARCH button.
z When setting “MANU,” if the STOP button is
pressed, the screen shifts to the sub screen and
the ON/OFF setting for each line can be adjusted.
Press the STOP button again to return to the main
screen.
z Metadata recorded on the tape will be output giving
UMID information first priority. When metadata is
output, set to a line other than the original
multiplexed line or select “BLANK.”
z Lines that are selected as being blanked in this
menu item are similarly blanked before being up-
converted when replaying the SD tape.
Sub screen (59/60 Hz mode)
693
GAMMA SEL
This selects gamma correction.
00
0000
BLANK :
0000
OFF :
Forced blanking
LINE 10&273
Gamma correction is not carried out.
0001
THRU :
0001
GAMMA1 :
:
No blanking
This corrects video images shot with the cine
gamma FilmREC mode of the Varicam to images
of film quality (equivalent to Telecine 5 of HD
Gamma Corrector in AJ-GBX27G).
12
LINE 22&285
Sub screen (50 Hz mode)
BLANK :
0002
GAMMA2 :
00
LINE
7&320
0000
0001
This corrects video images shot with the cine
gamma FilmREC mode of the Varicam to images
of film quality (equivalent to Telecine 6 of HD
Gamma Corrector in AJ-GBX27G).
Forced blanking
THRU :
No blanking
:
15
0003
GAMMA3 :
LINE 22&335
This converts video images shot with the cine
gamma FilmREC mode of the Varicam into the
Cineon curve appropriate for film recording.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
1023
768
*DW: With SD output (SD tape playback or down-converted
output)
512
TELECINE5
TELECINE6
Cineon
“_____” indicates the factory setting.
256
256
512
768 1023
<Notes>
z
Gamma correction is effective in the following conditions.
Š When the VTR operation mode is VV (TAPE) and
720p is displayed in the system format.
However, during cross convert from 720p > 1080i,
gamma correction is not effective for SD output.
z When “ON” is selected, the GAMMA lamp on the
front panel is on at all times.
When this unit is turned to OFF, this setting returns
to "OFF." The setting of user default returns to “OFF.”
z
z This item is not effective for 1394 output.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
AUDIO
No./Item
Description of setting
No./Item
Description of setting
701*1
CH1 IN LV
730*1
REC CUE
For setting the reference level of the analog audio
input (CH1).
For setting the input signal to be recorded on the CUE
track.
0000
0001
0002
0003
4dB
0dB
–20dB
–60dB
0001
CH1 :
Audio input CH1 signal
0002
CH2 :
Audio input CH2 signal
0003
CH3 :
702*1
CH2 IN LV
For setting the reference level of the analog audio
input (CH2).
Audio input CH3 signal
0004
Audio input CH4 signal
0005
Audio input CH5 signal
0006
Audio input CH6 signal
0007
CH4 :
0000
0001
0002
0003
4dB
0dB
–20dB
–60dB
CH5 :
CH6 :
706
CH1 OUT LV
For setting the reference level of the analog audio
output (CH1).
CH7 :
0000
0001
0002
4dB
0dB
–20dB
Audio input CH7 signal
0008
Audio input CH8signal
CH8 :
707
CH2 OUT LV
For setting the reference level of the analog audio
output (CH2).
0009
CH1+2 :
Audio input CH1 + CH2 mixed signal
0000
0001
0002
4dB
0dB
–20dB
0010
CH3+4 :
Audio input CH3 + CH4 mixed signal
0011
CH5+6 :
Audio input CH5 + CH6 mixed signal
710
MONIL OUT
LV
For setting the reference level of the analog audio
output (Lch).
0012
CH7+8 :
Audio input CH7 + CH8 mixed signal
0000
0001
0002
4dB
0dB
–20dB
0013
CH1~8 :
Audio input CH1 through CH8 mixed signal
<Notes>
711
MONIR OUT
LV
For setting the reference level of the analog audio
output (Rch).
z For analog input, this is interlocked to the settings
in menu No. 724 REC CH3/4.
z Audio signal is not recorded in the CUE track when
inputting 1394. (Mute)
0000
0001
0002
4dB
0dB
–20dB
731
PB FADE
For setting the processing for the audio edit points (IN
point, OUT point) and followon recording point during
playback.
712
MONI OUT
For selecting whether or not to enable the
headphone volume control knob for the volume of an
audio monitor output.
0000
AUTO :
0000
UNITY :
The processing follows the status established
during recording.
The signals are output at a fixed level.
0001
VAR :
0001
CUT :
The signal output is coupled with the headphones
volume control.
Cut processing is forcibly performed.
0002
FADE :
724*1
REC CH3/4
This selects the input signal to be recorded on the
audio CH3/4 track.
Fade processing is forcibly performed.
732
EMBEDDED
AUD
For setting whether to superimpose audio data onto
the HD SDI output and SD SDI output.
0000
CH1/2 :
Audio input CH1/2 signal.
0000
OFF :
0001
MUTE :
The audio data is not superimposed.
Mute
<Notes>
0001
ON :
The audio data is superimposed.
z This item is effective for analog input only.
z When selecting analog input, the same data as
CH1 to CH4 is recorded in CH5 to CH8.
746
MONI CH
SEL
For selecting the monitor output.
0000
MANU :
The signal selected by the MONITOR SELECT
button is output.
0001
AUTO :
The PCM audio signal is output when the speed
range is less than j1.0k to +1.0k; the CUE
AUDIO signal is output at all other speeds.
0002
PCM :
The PCM audio signal is output in the j32k to
i32k speed range.
<Note>
When the L/R selection is CUE with the MONITOR
SEL button on the front panel of this unit, CUE
AUDIO is output at all speeds, regardless of the
above menu.
During playback of DV/DVCAM tapes, the operation
uses a “MANU” setting regardless of the setting in
this item.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
“_____” indicates the factory setting.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
AUDIO (continued)
No./Item
Description of setting
No./Item
Description of setting
750
ANA CH1/2
SEL
For selecting the channel for the signal output to the
analog audio output terminal CH1/CH2.
782
EMBD CH
SEL
Set the channels to multiplex SD-SDI output.
0000
0001
CH1-4 :
CH5-8 :
0000
0001
0002
0003
CH1/2
CH3/4
CH5/6
CH7/8
<Note>
When tape other than DVCPRO HD (LP) is played,
CH1 to CH4 is always multiplexed.
759*1
DV PB ATT
For selecting the audio output level during DV format
playback.
783
AUDIO CH
SEL
For selecting channels that are adjusted with the
audio volume control on the front panel and displayed
on the audio level meter.
0000
OFF :
The audio output level is not attenuated.
0000
CH1-4 :
0001
ON :
Select CH1–CH4.
The audio output level is attenuated.
0001
CH5-8 :
Select CH5–CH8.
760*1
REC PT
MUTE
For selecting whether to mute the sound at the joins
in the recording during DV or DVCAM format
playback.
784
MONI SEL
INH
Select enabled/disabled for MONITOR SELECT
button operation on the front panel.
0000
OFF :
0000
OFF :
The sound is not muted.
Operation is enabled.
0001
ON :
0001
ON :
The sound is muted.
Operation is disabled.
0002
ON1 :
762
AUD RATE
CON
For setting whether the tape is to be played back
without passing the signals through the rate converter
(without activating the digital filter) in the digital audio
output unit.
Operation is disabled in the FULL display mode
while the operation is enabled only in the FINE
display mode.
0000
OFF :
The tape is played back without passing the signals
through the rate converter.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
0001
ON :
The signals are passed through the rate converter,
and the tape is played back.
<Note>
“_____” indicates the factory setting.
ON/OFF control is exercised for channels 1 through 8
at the same time. Separate settings cannot be
performed on a channel by channel basis.
765
CUE OUT
SEL
For setting whether to output the analog CUE signal
to CH1/2 for the analog audio output.
0000
OFF :
The analog CUE signal is not output.
The PCM audio signal is output when the speed
range is less than j1.0k to +1.0k; while the no
audio signal is output at any other speed.
0001
ON :
The analog CUE signal is output.
The PCM audio signal is output when the speed
range is less than j1.0k to +1.0k; while the
analog CUE signal is output at any other speed.
781*1
IN IMP SEL
For setting the analog audio input impedance.
0000
600 :
600h
0001
HIGH :
High impedance
<Note>
Regardless of this setting, the impedance is set to
3kh. when “–60 dB” is selected as the menu item
No.701 to 702 settings.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
DIF
No./Item
Description of setting
No./Item
Description of setting
880*1
DIF SPEED
892*1
DIF SIG CMD
For setting the transfer speed of the IEEE1394 digital
interface output.
For setting how to reply when signals requesting a
confirmation of the format is sent from an external
device connected by the IEEE1394 digital interface.
0000
S100 :
100 Mbps
0000
50M :
0001
S200 :
DVDPRO50 is forcibly returned.
200 Mbps
0001
25M :
0002
S400 :
DVDPRO is forcibly returned.
400 Mbps
<Note>
0002
DV :
DV is forcibly returned.
0003
AUTO :
When S100 has been selected as this item’s setting,
DVCPRO HD format signals cannot be input or
output.
The reply is the same format as the signal format
output from the IEEE1394 digital interface.
<Note>
882*1
DIF IN CH
For setting the input channel.
0000
:
When the unit is connected to a non-linear editing
system using 50M, 25M, and DV signal format, the
non-linear editing system may not operate properly. In
this case, set the value to reply with the format signal
supporting the connected signal format and start the
system.
0
:
63
0063
The input channel is fixed at the channel
corresponding to the number specified.
0064
AUTO :
894*1
HD
OUT
The input channel is not fixed at the channel
corresponding to the number specified. The input
channel is initialized to 63 when the power is
turned on.
For selecting channels that are adjusted with the
audio volume control on the front panel and displayed
on the audio level meter.
>
DIF
0000
HD :
DVCPRO HD
883*1
DIF OUT CH
For setting the output channel.
0001
50M :
0000
:
0
:
DVCPRO50
0002
DV :
0063
63
DV
The input channel is fixed at the channel
corresponding to the number specified.
895*1
For setting the format of the signals to be output from
the IEEE1394 digital interface when a 50M format
tape is played back.
0064
AUTO :
50M
OUT
>
DIF
The output channel is not fixed at the channel
corresponding to the number specified. The output
channel is initialized to 63 when the power is
turned on.
0000
50M :
DVCPRO50
0001
DV :
DV
<Note>
886*1
DIF CONFIG
Menu item for expansion purposes. Normally, use
DFLT as the setting.
When DV is selected as this item’s setting, the closed
caption signals and time code (VITC) signals in the
vertical blanking period are transmitted, but none of
the other signals in the vertical blanking period are
transmitted.
0000
0001
:
DFLT
1
:
255
0255
890*1
DIF AUD OUT
For setting the audio channels to which the signals
from the IEEE1394 digital interface are to be output in
the DV format when a DVCPRO HD tape or 50M
format tape is played back or when a DV tape in 4ch
mode is played by the audio signals and menu No.
891 DIF DV AUDIO is set to “LOCK48.”
896*1
For setting the format of the signals to be output from
the IEEE1394 digital interface when a 25M format
tape is played back.
0000
DVCPRO
0001
DV
25M
OUT
>
DIF
25M :
DV :
0000
CH1/2 :
CH1 and CH2
899*1
DIF SUPER
0001
CH3 and CH4
CH3/4 :
For setting whether the superimposed display is to be
output from the IEEE1394 digital interface when the
format is converted (from HD to 50M, from HD to DV,
from 50M to DV or from 25M to DV).
891*1
DIF DV
AUDIO
For setting forcible audio mode conversion when a DV
tape is played back and the audio signals are output
in the DV format.
0000
OFF :
The superimposed text is not displayed.
0000
THRU :
0001
ON :
Normal setting (the signals simply pass through).
The superimposed text is displayed.
0001
LOCK :
<Note>
Only TCR is displayed.
Forcible conversion to the LOCK mode (no
frequency conversion)
0002
LOCK48 :
Forcible conversion to 48kHz/2CH/LOCK.
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
“_____” indicates the factory setting.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup menus (continued)
MENU
No./Item
Description of setting
A02
P.ON LOAD
The unit starts with the selected user default loaded
when the power is turned on.
0000
OFF :
The unit starts with the previous set values.
0001
USER1 :
The unit starts with the selected user 1 loaded.
0002
USER2 :
The unit starts with the selected user 2 loaded.
0003
USER3 :
The unit starts with the selected user 3 loaded.
<Note>
Set value for SYSTEM menu is not loaded.
A04
PF1 ASSIGN
The setup menu item is stored to the PF1 button.
<Note>
Part of the items listed on the menu cannot be saved.
For details, refer to “PF (Programmable Function)”
A05
PF2 ASSIGN
The setup menu item is stored to the PF2 button.
<Note>
Part of the items listed on the menu cannot be saved.
For details, refer to “PF (Programmable Function)”
A06
PF3 ASSIGN
The setup menu item is stored to the PF3 button.
<Note>
Part of the items listed on the menu cannot be saved.
For details, refer to “PF (Programmable Function)”
“_____” indicates the factory setting.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Time code/user bits
Time code
Setting the external time code
The time code is used when the time code signal generated
by the time code generator (time code signal generator) is to
be recorded on the tape, its values are to be read by the time
code reader (time code signal reader), and the absolute
position of the tape is to be displayed in increments of hours,
minutes, seconds and frames.
The time code is written in the sub-code area (data area) of
the helical track. The VTR’s playback speed can be read
from the stop mode to slow-motion playback up to high-
speed play (approx. 50 a normal speed approx. 100 a when
using DVCPRO tape).
1 Set the VTR to stop mode.
2 Select “TC” using the COUNTER button.
3 Set the TCG switch to “EXT”. (External time code
selection)
4 The following settings can be selected with menu No.
507 EXT TC SEL.
EXT_L:
The time code values are indicated using the display and
superimpose functions.
The LTC signal input to the TIME CODE IN connector
(BNC) on the rear panel is recorded as time code.
SLTC:
The SLTC time code on the input video signal is
recorded.
SVITC:
TCR 00
ꢁ
:
07
:
04
:
24
ꢁ
ꢁ
ꢁ
Hours
Minutes Seconds
Frames
The SVITC time code on the input video signal is
recorded.
User bits
“User bits” refers to the 32-bit (8-digit) data frame among the
time code signals which has been released to users. It
enables operator numbers values to be recorded.
The alphanumeric characters which can be used for the user
bits are the figures 0 to 9 and the letters A to F.
<Note>
The LTC signal must be synchronized with the video
signal.
Reproducing the time code/user bits
Setting the internal time code
1 Set the VTR to stop mode.
1 Set the VTR to stop mode.
2 Select “TC” or “UB” using the COUNTER button.
2 Select “TC” using the COUNTER button.
3 Press the PLAY button.
Playback starts and the time code is shown on the
display.
3 Set the run mode for the time code generator using
menu No. 504 RUN MODE.
When the SUPER switch is set to ON, the time code
value is superimposed on the video signals from the
VIDEO MON connector.
REC:
The internal time code generator is advanced during
recording.
FREE:
When the power is on, the internal time code generator is
advanced regardless of the operation mode.
<Note>
When the time code signal cannot be read, the time code
is automatically interpolated by the CTL signal. The
display appears as shown below.
4 Set the TCG switch to REGEN mode.
T ¢ R 00 : 01 : 04 : 07 ¢
REGEN:
In this mode, the continuity of the original time code is
maintained.
A more detailed setting can be performed using menu
No. 505 TCG REGEN.
When the time
“
” : 1, 3 field
code signal cannot
be read, an asterix
(¢) is displayed.
“¢” : 2, 4 field
PRESET:
The colon between the seconds and
frames changes to a period during drop
frame mode.
In this mode, recording is commenced from the value
which was set by the TC PRESET button.
5
To preset the time code or user bit, take the following steps.
1. Set the TCG switch to “PRESET.”
2. Select “TC” or “UB” using the COUNTER button.
3. When the TC PRESET button is pressed, operation is
transferred to the setting mode, and the setting digits
start flashing on the counter display.
4. Operate the joystick, and set the preset value.
Left, right > for moving between digits;
Up, down > for changing the setting
zWhen the RESET button is pressed, the preset
value is reset to zero.
5. The preset value is set by pressing the TC PRESET
button.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Time code/user bits (continued)
Time code when power is not supplied
Even if the power is not supplied, the time code generator
operates for many hours (about 1 year) by using the backup
feature. And the accuracy when power is not supplied is
about 30 seconds a month.
<Notes>
z When the time code generator advances regardless of the
operation mode, the backup function is enabled.
Š When the TCG switch in the front panel is set to
“PRESET” and the menu No. 504 RUN MODE is set
to “FREE.”
Š When the TCG switch in the front panel is set to “EXT”
and the external time code input set in menu No. 507
EXT TC SEL is disconnected from the connector on
the rear panel.
z When the settings in menu No. 25 SYSTEM FERQ are
revised, the advanced data will be cleared.
Timecodes recorded by this product
Recorded timecode
Menu
No. 507 EXT TC SEL
Selected video
input signal
TCG switch
SBC area
Internal TCG value
VAUX area
Timecode on IEEE1394 digital
input (VAUX area)
1394
INT (REGEN/
PRESET)
---
(Refer to the following table.)
3
HD SDI
1394
SVITC on input video signal*
Timecode on IEEE1394 digital
input (SBC area)
Timecode on IEEE1394 digital
input (VAUX area)
EXT_L
Timecode from TIME CODE IN
3
HD SDI
SVITC on input video signal*
1
connector input*
Timecode on IEEE1394 digital
input (SBC area)
Timecode on IEEE1394 digital
input (VAUX area)
1394
EXT
SLTC
2
3
HD SDI
1394
SLTC on input video signal*
SVITC on input video signal*
Timecode on IEEE1394 digital
input (SBC area)
Timecode on IEEE1394 digital
input (VAUX area)
SVITC
2
3
HD SDI
SVITC on input video signal*
SVITC on input video signal*
*1 The internal TCG value is used when the signal cannot be detected from the TIME CODE IN connector input.
*2 The internal TCG value is used when the SLTC or SVITC cannot be detected on the input video signal.
*3 Nothing is recorded if the SVITC cannot be detected on the input video signal.
Menu
Recorded timecode
For assemble editing
For frame-by-frame
For continuous
recording
For insert editing
(Time code selection)
TCG switch
No.503
TCG MODE
No.505
TCG REGEN
No.506
REGEN MODE
5
shooting*
TC
UB
TC
UB
TC
UB
TC&UB
TC
REGEN
REGEN
REGEN
PRESET
REGEN
REGEN
PRESET
REGEN
REGEN
PRESET
REGEN
SW
---
UB
PRESET
PRESET
PRESET
PRESET
---
PRESET
AS&IN
ASSEM
INSRT
AS&IN
ASSEM
INSRT
AS&IN
ASSEM
INSRT
REGEN
REGEN
TC&UB
TC
PRESET
REGEN
PRESET
REGEN
REGEN
PRESET
REGEN/
AUTO
PRESET
PRESET
PRESET
REGEN
PRESET
4
PRESET*
REGEN
UB
REGEN
PRESET
PRESET
REGEN
*4 When menu No. 503 TCG MODE is set to AUTO, the REGEN and PRESET selection of the TCG switch is disabled.
*5 When menu No. 154 AUTO BACK is set to “OFF”, scene-to-scene continuity will be a normal recording.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Superimpose screen
The control signals, time code, etc. are displayed using
abbreviations.
Characters displayed
The background of characters superimposed on the display
can be changed using menu No. 009 CHARA TYPE.
TV monitor
TCR ¢¢ : ¢¢ : ¢¢ : ¢¢
TCR ¢¢ : ¢¢ : ¢¢ : ¢¢
TCR ¢¢ : ¢¢ : ¢¢ : ¢¢
TV monitor
TV monitor
Abbreviations:
Display position
CTL : Control signal count value
The position of the characters superimposed on the display
can be changed using menus No. 007 CHARA H-POS and
No. 008 CHARA V-POS.
TCR : Time code data recorded in the SBC area
TCR.: Time code data recorded in the VAUX area
UBR : User bit data recorded in the SBC area
UBR.: User bit data recorded in the VAUX area
TCG : Time code data of the time code generator
UBG : User bit data of the time code generator
<Notes>
TCR ¢¢ : ¢¢ : ¢¢ : ¢¢
TCR ¢¢ : ¢¢ : ¢¢ : ¢¢
z [T ¢ R], [T ¢ R.], [U ¢ R] or [U ¢ R.] is displayed when the
data has not been read correctly from the tape.
z When the 23.98/24 Hz, 25 Hz (HD/SD), or 50Hz (HD/SD)
mode is selected in menu No. 25 SYSTEM FREQ,
indications on the CTL and TCR will be “--:--:--:--”.
TV monitor
TV monitor
Operation mode
The VTR’s operation mode can also be displayed using
menu No. 006 DISPLAY SEL.
TCR ¢¢ : ¢¢ : ¢¢ : ¢¢
STOP
VTR operation mode
TV monitor
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Video head cleaning
For further details on how to actually clean the heads,
consult with your dealer.
This unit is equipped with an auto head cleaning function
which automatically reduces the amount of dirt on the video
heads. However, in order to maximize the unit’s reliability, it
is recommended that the video heads be cleaned as and
when appropriate.
Condensation
Condensation occurs due to the same principle involved
when droplets of water form on a window pane of a heated
room. It occurs when the unit or tape is moved between
places where the temperature or humidity varies greatly or
when, for instance:
When moving the unit to locations such as these, leave it
standing for about 10 minutes rather than switching on the
power immediately. If condensation occurs in the unit, “E-
20” will flash on the counter display and the cassette will be
automatically ejected.
z It is moved to a very humid place full of steam or a room
immediately after it has been heated up.
Leave the unit with the power on until “E-20” is cleared from
the display.
z It is suddenly moved from a cold location to a hot or humid
location.
Maintenance
Before starting any maintenance work, switch the power to
OFF and, holding the plug, unplug the cord from the socket.
Use a soft cloth to clean the outside of the unit.
For stubborn dirt or stains, wipe the unit with a cloth that has
been lightly dampened with well-diluted kitchen detergent
and wrung out thoroughly.
<Note>
Do not use alcohol, benzene, thinners or any other solvents
as they may affect the color of external parts or damage the
unit’s coating.
After wiping off the dirt with the damp cloth, finish it off with a
dry cloth.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Error messages
DIAG menu
This displays the VTR information.
2 3
The VTR information includes the warning information,
hours meter (usage time) information and UMID information.
The DIAG menu appears on the TV monitor when the
VIDEO OUT connector on the rear panel is connected to the
TV monitor.
Displaying the DIAG menu
REC
PB
CH1
CH2
CH1
CH2
1 Press the MENU button while holding down the PF
button.
CH1/5
CH2/6
CH3/7
CH4/8
PB
The DIAG menu screen appears on the TV monitor, and
a message appears on the counter display.
1
2 Press the SEARCH button.
When a warning occurs in this unit, the error number is
indicated on the counter display.
Each time this button is pressed, the display changes by
one step in the following sequence: “WARNING” >
“HOURS METER” > “UMID INFO” > “DIF STATUS1”
> “DIF STATUS2.”
Open the DIAG menu to display a description of the error on
the counter display or monitor TV.
When a operational malfunction has occurred in the unit, the
error number flashes on the counter display.
3 When the MENU button is pressed again, the original
display is restored.
Displaying the “HOURS METER” information
When the joystick is moved up or down, the cursor (¢) moves, and a description of the item where the cursor is located is
shown on the counter display.
NO.
Ser
H00
H01
Item
¢¢¢¢¢¢¢¢¢
OPERATION
DRUM RUN
Description
Displays the unit’s serial No.
Displays the time that the power has been supplied in one-hour units.
Displays the time that the drum has been rotating in one-hour units.
Displays the duration for which the tape has been running in the FF, REW, PLAY, SEARCH (JOG,
SLOW, SHTL) and REC modes (but not in the JOG, SLOW and SHTL STILL modes) in 1-hour
increments.
H02
TAPE RUN
H03
H04
H11
THREADING
F LOADING
DRUM RUNr
The number of times for threading (loading)/ unthreading (unloading) is displayed in single units.
Displays the number of times front loading has been performed in single units.
Displays the time that the drum has been rotating in one-hour units. (Can be reset)
Displays the duration for which the tape has been running in the FF, REW, PLAY, SEARCH (JOG,
SLOW, SHTL) and REC modes (but not in the JOG, SLOW and SHTL STILL modes) in 1-hour
increments. (This item can be reset.)
H12
H13
TAPE RUNr
The number of times for threading (loading)/ unthreading (unloading) is displayed in single units. (Can
be reset)
THREADINGr
H14
H30
F LOADINGr
POWER ON
Displays the number of times front loading has been performed in single units. (Can be reset)
The number of times the power has been turned on is displayed in single units.
<Notes>
z The resettable items in the “HOURS METER” information are reset by the dealer when maintenance work is performed.
z No operations can be performed using the SEARCH button or the joystick while the DIAG menu is displayed.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Error messages (continued)
If “T&S&M” is selected in the menu No. 008 DISPLAY SEL, a message appears in the modedisplay whenever a warning or
error occurs. When multiple events occur, the event with the highest priority is displayed.
Priority
High
Display
Error messages
Description
When an operational malfunction has occurred in the unit, the error number flashes and the
error message is indicated on the counter display.
(See error message table)
When SG has been selected as the input signal by the INPUT SELECT button, the “INT SG”
display will appear for the first two seconds at the start of operation (EE mode) when the REC
button is pressed.
INT SG
If there are no input signals--with the exception of the analog audio signals-- supplied to the
connectors selected by the INPUT SELECT button, the “NO INPUT” display will appear for the
first two seconds at the start of operation (EE mode) when the REC button is pressed.
NO INPUT
When a warning occurs in this unit, the error number and warning message are indicated on the
counter display. When multiple warnings occur, the warning with the highest priority is
displayed.
Warning messages
(See error message table)
Low
UMID information display
This is displayed when UMID information is present on the input signal in EE mode.
This lamp lights during tape playback when UMID information has been recorded on the tape. “NO-INFO” is displayed when
there is no UMID information.
Display
MATNO
Description
Material number
COPY
Instance number (No. of copies)
Country, organization, user
OWNR
Reception status from GPS satellites when recording spatial coordinates
(height above sea level, longitude and latitude):
HOLD: No reception from any satellite
POS
2D:
Reception possible, but number of satellites is insufficient. Height
above sea level will not be accurate.
Good reception
3D:
DATE
TIME
Date
UTC (Coordinated Universal Time) and time difference with UTC
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Error messages (continued)
Displaying the warning information
z A warning message appears when a warning has occurred. “NO WARNING” appears when a warning has not occurred.
z When more than one warning has occurred simultaneously, move the joystick up or down to check the description of each
warning.
Warning messages
Priority Monitor display
Description
Corrective action
VTR operation
If condensation is detected, the error number flashes and
the unit transfers to eject mode. The drum rotates after
the cassette is ejected to eliminate the condensation.
Once the unit is released from condensation status, the
error message display is cleared and the VTR is able to
be used.
High
E-20
(DEW)
Leave the power on and wait. EJECT
z If condensation is detected in the eject mode, the drum
starts rotating as soon as it is detected.
z If condensation is detected when the cassette has
been inserted, the drum rotation is stopped, and after
the tape is ejected, the drum starts rotating.
(When “SLTC” is selected in menu No. 032 REC REF)
Appear when a time code for a signal input into the HD
SDI IN connector is not stepping at the standard rate in
synchronizing the image frames to be recorded with the
time code.
E-95
(INVALID
EMBEDDED TC)
Check the time code
information of the input signal. continues.
Operation
If the cable connection is in
Signal input
loop status, reconnect to 1 to and output
through the
E-92
(1394 INITIAL
ERROR)
Display if the IEEE1394 digital interface connection status 1.
is irregular
If not using the loop
IEEE1394
connection, turn the POWER digital interface
switch OFF > ON.
is stopped.
This appears when the signals supplied from the
IEEE1394 digital interface are not DVCPRO/DV format
signals.
No recording o
perations are
possible.
E-04
(UNKNOWN SIG)
Check that the 1394 input has
been connected properly.
Operation
E-90
This appears when the initialization process fails during
communication via the IEEE1394 digital interface.
Check the input signal.
1
(NOT 1X 100M SIG)
continues.*
This appears when the compressed video signals
supplied from the IEEE1394 digital interface are irregular Check the 1394 input signals.It
E-16
(INVALID VIDEO
SIG)
Operation
signals.
is possible that playback
1
z This warning appears only during recording operations. signals of an unrecorded tape
continues.*
In such cases, no signals are recorded on the tape,
and only erasure of existing signals is performed.
are being input.
This appears when the audio signals supplied from the
IEEE1394 digital interface are irregular signals.
z This warning appears only during recording operations. than 1x playback signals are
In such cases, the signals are recorded with the audio being input from a VTR or
signals muted.
Check the 1394 input signals.It
is possible that signals other
E-17
(INVALID AUDIO
SIG)
Operation
continues.*
2
other device.
This appears when the time code information supplied
from the IEEE1394 digital interface is irregular
information.
z This warning appears only during recording operations.
In such cases, the internally generated time code is
recorded.
Check the time code of the
device which is supplying the
time code.
Operation
E-18
(INVALID TC SIG)
3
continues.*
This appears when the signals supplied to the IEEE1394
digital interface are at variance from the system format
which is set by this unit.
Operation
continues.*
E-14
(NO MATCH SIG)
Check the input signal.
1
This appears when the fan motor has shut down.
z The power automatically turns off if 5 minutes pass with
the fan stopped.
E-10
(FAN STOP)
Check the fan for foreign
matter.
Operation
continues.
This appears when a blank section lasting for more than
one second on the tape has been detected during
playback.
A blank section is identified as such when all the following
conditions are met:
z There are no output signals from any of the heads.
z The playback data cannot be read.
Check the tape. It is possible
that an unrecorded tape has
been loaded.
E-09
(NO RF)
Operation
continues.
z There is no CTL signal (DV/DVCAM tapes excluded).
*1 This error message always appears in the EE mode.
In such a case, black signals are recorded as the video signals, and the audio signals are muted.
*2: This error message always appears in the EE mode.
In such a case, the audio signals are muted.
*3: This error message always appears in the EE mode.
In such a case, the time code of the time code generator inside this unit is recorded as the time code signal.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Error messages (continued)
Warning messages (continued)
Priority Monitor display
Description
Corrective action
VTR operation
E-00
(SERVO NOT
LOCKED)
This appears when the servo is not locked for three or
more seconds during playback or recording.
Operation
continues.
Check the tape.
(In 23.98/24 Hz mode)
Display when the time code is recorded in DF mode. On
the drop point of the time code, the video output is
garbled and audio output is muted.
E-93
(INVALID TC
MODE)
Use the original tape recorded
with the variable frame rate
camera.
Operation
continues.
Operation of VTR continues.
When using this unit to playback a tape recorded from a
variable frame rate camera, it is necessary to record the
time code in NDF mode.
(In 23.98/24 Hz, 25 Hz, 50 Hz mode)
Appear when the relationship between the active frame
information and time code is not regular during playback.
The video output may not be regular (not smooth).
Operation of VTR continues.
The active frame information (top frame of the switched
frame image) is recorded on the tape from a variable
frame rate camera. To play it back with this unit, it is
necessary to detect the 0 frame of the time code at the
activation frame position.
E-94
(TC SEQUENCE
UNMATCH)
Use the original tape recorded
with the variable frame rate
camera.
Operation
continues.
This appears when an envelope level approximately one-
third of the normal level has been detected for more than Clean the video heads.
one second during playback or recording.
E-01
(LOW RF)
Operation
continues.
E-02
(HIGH ERROR
RATE)
This appears when the error rate has increased to the
extent that correction or interpolation was applied to
either the video or audio playback signals.
Operation
continues.
Clean the video heads.
Low
Error messages
VTR
operation
Monitor display
Description
Corrective action
The unit switches to eject mode and if the cassette fails to move up
within 6 seconds, this error number flashes on the display.
<Note>
If the cassette does not move down inside the machine even when 6
seconds have elapsed since the cassette was inserted, the VTR is
transferred to the eject mode.
E-29
FRONT LOAD
MOTOR
Set the POWER switch to OFF
and then to ON again.
STOP
If the unloading operation is not completed within 6 seconds, this
error number flashes on the display.
<Note>
When the loading operation is not completed within 6 seconds, the
VTR is transferred to the eject (unloading) mode.
E-31
Set the POWER switch to OFF
and then to ON again.
STOP
STOP
LOADING MOTOR
E-35
If there is no response from the servo microcomputer for 1 second Set the POWER switch to OFF
SERVO CONTROL
ERROR
or more, this error number flashes on the display.
and then to ON again.
E-37
SERVO COMM
ERROR
If 10 seconds or more elapses and the servo microcomputer has not
followed orders issued by the system control microcomputer, this
error number flashes on the display.
Set the POWER switch to OFF
and then to ON again.
STOP
STOP
STOP
This appears when the automatic reel and capstan rotation
adjustment, which is performed in the EJECT mode, has not been
carried out properly when the unit’s power was switched on.
E-38
Set the POWER switch to OFF
and then to ON again.
SERVO FG ERROR
E-51
FRONT LOAD
ERROR
If the take-up reel rotates without engaging for a specific period of
time during the start or end processing operation while loading is
underway (half position), this error number flashes on the display.
Set the POWER switch to OFF
and then to ON again.
If the take-up reel fails to take up the tape while the tape is traveling
in the state where the total amount of the tape has not yet been
detected after the cassette was inserted, this error number flashes and then to ON again.
on the display.
E-52
W-UP REEL NOT
ROTA
Set the POWER switch to OFF
STOP
STOP
If there is an abnormally large discrepancy between the amount of
tape taken up by the take-up reel and the amount of tape supplied
by the supply reel while the tape is traveling after the total amount of
the tape begins to be detected, this error number flashes on the
display.
E-53
WINDUP ERROR
Set the POWER switch to OFF
and then to ON again.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Error messages (continued)
Error messages (continued)
VTR
operation
Monitor display
Description
Corrective action
E-55
UNLOAD ERROR
If the tape has not been taken up during unloading, this error
number flashes on the display.
Set the POWER switch to OFF
and then to ON again.
STOP
E-57
S-FF/REW
TIMEOVER
If the start or end processing operation is not completed, this error Set the POWER switch to OFF
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
STOP
number flashes on the display.
and then to ON again.
E-59
DRUM ROTA TOO
SLOW
If the cylinder motor speed is abnormally low, this error number
flashes on the display.
Set the POWER switch to OFF
and then to ON again.
E-60
DRUM ROTA TOO
FAST
If the cylinder motor speed is abnormally high, this error number
flashes on the display.
Set the POWER switch to OFF
and then to ON again.
E-61
CAP ROTA TOO
SLOW
If the capstan motor speed is abnormally low, the error number
flashes on the display.
Set the POWER switch to OFF
and then to ON again.
E-64
If the supply reel motor speed is abnormally high, the error number Set the POWER switch to OFF
flashes on the display. and then to ON again.
S REEL ROTA TOO
FAST
E-67
If the take-up reel motor speed is abnormally high, the error number Set the POWER switch to OFF
flashes on the display. and then to ON again.
T REEL ROTA TOO
FAST
E-69
T REEL TORQUE
ERR
If excess torque being applied to the take-up reel motor is detected, Set the POWER switch to OFF
the error number flashes on the display.
and then to ON again.
E-70
S REEL TORQUE
ERR
If excess torque being applied to the supply reel motor is detected or
an abnormal current flowing to the current detection resistor is
detected, this error number flashes on the display.
Set the POWER switch to OFF
and then to ON again.
E-71
CAP TENSION
ERROR
If abnormal tension at the supply side is detected in the capstan
mode, the error number flashes on the display.
Set the POWER switch to OFF
and then to ON again.
E-72
REEL TENSION
ERROR
If abnormal tension at the supply side is detected in the reel mode, Set the POWER switch to OFF
the error number flashes on the display.
and then to ON again.
E-73
REEL DIR
UNMATCH
If the take-up reel motor has rotated in the reverse direction, this
error number flashes on the display.
Set the POWER switch to OFF
and then to ON again.
E-74
DRUM TORQUE
ERROR
If excess torque being applied to the cylinder motor is detected, this Set the POWER switch to OFF
error number flashes on the display.
and then to ON again.
If a problem has been encountered in communication between the
servo microcomputer and mechanism relay board, this error number
flashes on the display.
E-78
Set the POWER switch to OFF
and then to ON again.
STOP
STOP
M-IF COMM ERROR
Check the output voltage of the
equipment supplying DC
power.
E-bA
BATTERY
This appears when the input DC voltage has dropped below the
undercut voltage.
<Note>
Consult your dealer if the error message display persists even after the unit has been restarted.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Emergency eject
Procedure to ejecting the tape manually in an emergency
If the cassette tape fails to be ejected even when the EJECT button is pressed, it can be ejected as follows.
z Follow the steps below after making absolutely sure that the unit’s power has been turned off.
1 Remove the top panel.
3 Check that the posts have unloaded the tape and that the
tape is completely housed inside the cassette.
2 Use a Phillips-head screwdriver to push in the red plastic
gear (A) and turn it counterclockwise while keeping it
pushed in. The mechanism that winds up the tape is
activated by this, and it makes a latching sound. Ignore
the sound, and turn the gear through about 10
revolutions.
4 Once the tape has been completely returned inside the
cassette case, use the Phillips-head screwdriver to push
in the red plastic gear (B) in front of the front loading
motor’s worm gear and, while keeping it pushed in, turn it
clockwise to eject the cassette.
<Note>
<Note>
Turning the gear more than necessary will strain the
cassette, possibly resulting in tape damage.
When closing the cassette cover, take care not to catch
the tape.
Plastic gear
(A)
Plastic gear
(B)
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
[GENERAL]
[VIDEO]
_Digital video
Sampling frequency:
Power supply: AC 100-240 V , 50/60 Hz, 85 W
DC 12 V, 5.3 A, 64 W
Y:
PB/PR: 37.125 MHz
Quantizing:
74.25 MHz
indicates safety information.
8 bits
Ambient operating temperature:
5°C to 40°C (41°F to 104°F)
Storage temperature:
Video compression system:
DCT + variable length code
Video compression ratio:
1:6.7
–20°C to 60°C (–4°F to 140°F)
Ambient operating humidity:
10% to 80% (no condensation)
Dimensions (WkHkD):
214 mm k 132 mm k 442 mm
(8-7/16 inches k 5-1/4 inches k 17-3/8 inches)
(Protruding portion is not included)
Weight:
8.5 kg (18.74 lb)
Recording format:
DVCPRO HD-LP
Recording video signals:
1080i/59.94 Hz, 50 Hz,
Error correction:
Reed-Solomon product code
Video recording bit rate:
100 Mbps
_Video input connectors
HD serial digital input:
BNC k 1
(compliant with SMPTE 292M/296M/299M
standards)
Reference input:
Black burst/HD tri-level sync automatic switching
BNC k1 (loop-through k 1)
75 h termination automatic switching
720p/59.94 Hz, 50 Hz, 60 Hz (only Varicam)
switchable
Recording audio signal:
48 kHz, 16 bits, 8 channels
Recording tracks:
_Video output connectors
HD serial digital output:
Š Digital video/audio: Helical track
Š Time code: Helical track (sub code area)
Š Cue signal: 1 track
BNC k 2
(compliant with SMPTE 292M/296M/299M
standards)
Š Control (CTL) signal: 1 track
Playback formats:
(information superimposing ON/OFF)
SD serial digital output:
DVCPRO HD-LP, DVCPRO HD, DVCPRO50,
DVCPRO, DV-SP, DVCAM
Recording tape speed:
67.640 mm/sec (in 59.94 Hz mode)
67.708 mm/sec (in 50/60 Hz mode)
Recording time:
64 min (when using AJ-HP64ELG)
Tapes used:
Metal tapes
FF/REW time:
BNC k 1 (compliant with SMPTE 259M-C/
272M-A, ITU-R BT.656-4 standards)
(information superimposing ON/OFF)
Analog composite output:
BNC k 1
VIDEO 1, VIDEO 2
(information superimposing ON/OFF)
HD analog component output:
BNC k 3 (Y/PB/PR)
(information superimposing ON/OFF)
(VIDEO1 and HD analog component Y output
are switched.)
Approx. 90 sec (when using AJ-HP64ELG)
Editing accuracy:
0 frame
(when time code is used, in 50 Hz, 59.94 Hz or
60 Hz mode)
Tape timer accuracy:
2 frames (when continuous CTL signal is used)
(For slow replay at half speed or less, errors may
occur in the CTL count.)
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (continued)
_Video output adjustment ranges
z Component style
[AUDIO]
HD/SD SDI, HD analog componennt, composite
output Y gain:
_Digital audio
Sampling frequency:
48 kHz (synchronized with video)
Quantizing:
–
to +3 dB
HD/SD SDI, HD analog componennt, composite
output PB gain:
16 bits
–
to +3 dB
Frequency response:
20 Hz to 20 kHz 1 dB (at reference level)
Dynamic range:
More than 85 dB (1 kHz, emphasis OFF)
Distortion:
HD/SD SDI, HD analog componennt, composite
output PR gain:
–
to +3 dB
HD/SD SDI, HD analog componennt, composite
output Y black level:
Less than 0.1%
10%
(1 kHz, emphasis OFF, reference level)
Crosstalk:
z Composite style
HD/SD SDI, HD analog componennt, composite
output video gain:
Less than –80 dB (1 kHz, between 2 channels)
Wow & flutter:
Below measurable limits
Headroom:
–
to +6 dB
HD/SD SDI, HD analog componennt, composite
output chroma gain:
20 dB (For AJ-HD1400P)
18 dB (For AJ-HD1400E)
–
to +3 dB
HD/SD SDI, HD analog componennt, composite
output chroma phase:
_Audio input connectors
Analog input (CH1, CH2):
XLR k2, 600 h/high impedance switchable
+4/0/–20 dBu/–60 dBu switchable
HD serial digital input:
30°
HD/SD SDI, HD analog componennt, composite
output Y setup:
10%
z System phase
BNC k1
HD serial digital output system phase:
1080i: 0.5H (in 13.5 ns increments)
59.94/60 Hz: 1100 samples
Compliant with SMPTE 292M/296M/299M
standard
50 Hz:
1320 samples
_Audio output connectors
Analog output (CH1, CH2):
XLR k 2, low impedance
23.98/24 Hz: 1375 samples
720p: 0.5H (in 13.5ns increments)
59.94/60 Hz: 825 samples
+4/0/–20 dBu switchable
50 Hz:
990 samples
HD serial digital output:
Composite video output system phase:
BNC k 2 (compliant with SMPTE 292M/296M/
299M standard)
0.5H (in 37 ns increments)
59.94 Hz:
50 Hz:
Composite video output SC phase:
858 samples
864 samples
SD serial digital output:
BNC k 1 (compliant with SMPTE 259M-C/272M-
A/ITU-R BT.656-4 standards)
Monitor output (L, R):
180° or more
zXLR k 2, low impedance
+4/0/–20 dBu switchable
zPin jack k 2
Headphone output:
3.5-mm stereo mini jack k 1, 8 h, level variable
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (continued)
[OTHER CONNECTORS]
Time code input:
BNC k1, 0.5 to 8 Vp-p, 10 kh
Time code output:
BNC k1, low impedance, 2.0 0.5 Vp-p
(with 600 h load)
RS-422A input:
D-sub 9-pin
RS-422A interface
Encoder remote
D-sub 15-pin
DC power output:
4 pins k1, DC 12 V, 250 mA, for AJ-A95
1394 input/output connector:
Connector: 6-pin type
Transmission rate:
400 Mbps, 200 Mbps, 100 Mbps;selectable
Transmission data:
Compliant with IEEE1394-1995
Compliant with IEC 61883-Part1, Part2
Control command:
Compliant with AV/C command set
[Accessories]
Power supply cord k 1 (AJ-HD1400P)
Power supply cord k 2 (AJ-HD1400E)
Weight and dimensions shown are approximate.
Specifications are subject to change without notice.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on Disposal for Users of Waste Electrical & Electronic Equipment
(private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic products
should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where they will
be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your
local retailer upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on
human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority
for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY
UNIT COMPANY OF PANASONIC CORPORATION OF NORTH AMERICA
Executive Office:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7196
Southeast Region: (201) 348-7162
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Government Marketing Department:
One Panasonic Way 2E-10, Secaucus, NJ 07094 (201) 348-7587
Broadcast PARTS INFORMATION & ORDERING:
9:00 a.m. – 5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880
Emergency after hour parts orders (800) 334-4881
TECHNICAL SUPPORT:
Emergency 24 Hour Service (800) 222-0741
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010
Panasonic de Mexico S.A. de C.V.
Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127
Panasonic Puerto Rico Inc.
San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300
Professional & Broadcast IT Systems Business Unit Europe
Panasonic Marketing Europe GmbH
Hagenauer Str. 43, 65203 Wiesbaden-Biebrich Deutschland Tel: 49-611-235-481
P E
© 2006 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|