Panasonic Stereo System PV D4743 User Manual

DVD/VCR DECK

Operating Instructions

Model No. PV-D4743/PV-D4743S

Connections and Initial Setup Procedures are on pages 12 to 17.

MULTI FORMAT PLAYBACK

Ability to play back may depend on recording conditions.

As an ENERGY STAR^®Partner, Matsushita Electric Corporation

of America has determined that this product or product model

meets the ENERGY STAR^®guidelines for energy efficiency.

Please read these instructions carefully before attempting to connect, operate or adjust this

product. Please save this manual.

Spanish Quick Use Guide is included.

(Guía para rápida consulta en español está incluida.)

LSQT0674B

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Precautions/Mesures de sécurité

WARNING: To prevent fire or shock hazard, do not expose this

equipment to rain or moisture.

CAUTION: To prevent electric shock, match wide blade of plug to

wide slot, fully insert.

Avertissement: Afin de prévenir tout risque d’incendie ou de chocs

électriques, ne pas exposer cet appareil à la pluie ou

à une humidité excessive.

Attention: Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de la

prise et pousser jusqu’au fond.

This symbol warns the user that uninsulated voltage

within the unit may have sufficient magnitude to cause

electric shock.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Therefore, it is dangerous to make any kind of contact

with any inside part of this unit.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

This symbol alerts the user that important literature

concerning the operation and maintenance of this unit

has been included. Therefore, it should be read

carefully in order to avoid any problems.

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

CAUTION:

LASER RADIATION

WHEN OPEN DO NOT

UNIT IS A CLASS I LASER PRODUCT.

HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD

CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.

BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

STARE INTO BEAM.

ATTENTION:

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE

YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER

OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

RAYONNEMENT

LASER EN CAS

D’OUVERTURE.

NE PAS REGARDER

DANS LE FAISCEAU.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL.

(Inside of product)

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when operated in a residential

environment. If this equipment does cause interference to radio or television reception, which can be

determined by turning the equipment off and on, use the equipment in another location and/or utilize

an electrical outlet different from that used by the receiver.

If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the

booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting to

other devices.) Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

FCC Warning: Any unauthorized changes or modifications to this equipment would void the user’s

authority to operate.

Region Management Information:

This DECK is designed and manufactured to respond to the

Region Management Information that is recorded on a DVD

disc. If the Region number described on the DVD disc does

not correspond to the Region number of this DECK, this

DECK cannot play this disc.

Example:

ALL

GThe Region number for this DECK is “1”.

GThe Player will play DVD-Video marked with labels

containing “1” or “ALL”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before Using

Disc formats supported by this DECK

Congratulations

DECK can play back discs bearing any of the following

on your purchase of one of the most

[Discs Played 8cm (3") or 12cm (5")]

marks:

sophisticated and reliable products on the

market today. Used properly, it will bring you

years of enjoyment. Please fill in the

Logo

Disc type

DVD (DVD-Video)

information below. The serial number is on the

tag located on the back of your DECK.

DVD-R (DVD-Video formatted

discs [finalized])

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.

Video CD

CD (CD-DA)

CD-R/CD-RW (CD-DA,Video CD

formatted discs [finalized])

WMA, MP3, JPEG

• Serial No.

Discs which cannot be played

Accessories

• DVD with Region No. other than “1” or “ALL”

• DVD of PAL system, DVD-Audio, DVD-RAM, DVD-ROM,

DVD-RW, DVD+RW, CD-ROM, CDV, CD-G, CVD, SVCD,

SACD, Divx Video Disc and Photo-CD

Remote Control

LSSQ0374 (PV-D4743)

LSSQ0375 (PV-D4743S)

Notes

• Do not use irregularly shaped discs (e.g. heart-

shaped), as these can damage the unit.

• It may not be possible to play CD-R, CD-RW and

DVD-R in all cases due to the type of disc or

condition of the recording.

Batteries 2 “AA”

Disc Handling

Handling precautions

RF Coaxial Cable

LSJA0372

• Sticking a label on the disc may impair DVD-R

playback.

• Do not attach sticker to discs. (Do not use discs

with exposed adhesive from tape or left over

peeled-off stickers.)

• Only hold disc by edges as shown below.

Fingerprints, dirt and scratches can cause skipping

and distortion.

• Do not write on label side of disc.

• Never use record cleaning sprays, benzine, thinner,

static electricity prevention liquids, or any other

solvent.

To order accessories, call toll free

1-800-332-5368.

Loading the Batteries

Disc tray

Disc

1) Open cover.

• Do not try to close disc tray when disc

is not properly placed.

To clean disc surface

2) Insert batteries as

marked.

With a soft, damp (water only) cloth,

gently wipe from the center hole to the

outer edge as shown below. (Wiping in a

circular pattern will scratch the surface.)

If disc is brought from a cold to a

warm environment, moisture may

form on the disc

3) Close cover.

Wipe away moisture with a soft, dry, lint-free cloth

before using disc. (See above.)

Improper disc storage

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese

batteries.

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

DVD / VCR

Important Safeguards and Precautions ............................ 2, 3

Before Using ............................................................................4

DECK & Cassette Information ........................................... 6 , 7

Location of Controls ....................................................... 8 ~ 10

Displays (On Screen Displays and Multi Function Display) .................... 11

Connections .................................................................. 12 ~ 15

Initial Setup for Basic Connections (Ready to Play) .......... 16, 17

VCR

Reset Language, Channels, Clock, VCR’s Output Channel ... 18, 19

Playback/ Record on a Tape........................................... 20, 21

DVD

Basic DVD Operation ...................................................... 22, 23

Timer Recording.............................................................. 24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System .................... 26, 27

Multi-Brand Control Feature ........................................... 28, 29

Tape Operation (Search System) ....................................... 30 ~ 32

Special VCR Features ..................................................... 33, 34

Copying Your Tapes (Dubbing) ......................................................... 35

Disc Operation ............................................................... 36 ~ 40

DVD Operation using On-Screen Displays ................. 41 ~ 42

MP3/WMA/JPEG Playback Operation .......................... 43 ~ 45

DVD Lock Feature ................................................................. 46

Settings for DVD Operation .......................................... 47 ~ 49

Language Code List.............................................................. 50

DVD / VCR

Warning and Instruction Displays........................................ 51

Before Requesting Service............................................. 52, 53

Limited Warranty ............................................................. 54, 55

Customer Services Directory ...............................................55

Spanish (Español) Quick Use Guide............................ 56 ~ 61

Index................................................................................. 62, 63

Download from Www.Somanuals.com. All Manuals Search And Download.

DECK & Cassette Information

Head Cleaning

Prevent Accidental Tape Erasure

Playing older or damaged tapes may eventually

cause video heads to become clogged.

Break off the tab to

prevent recording.

Video Head Clog Sensor

During playback, this

Record Tab

Screw driver

screen appears if

EO HEADS

EED CLE NG

NSERT HEAD

NG CASSETT

OR REFER MANUAL

MAY

clogging is detected.

To remove screen,

press PLAY on the

remote or DECK.

PLEASE

CLE

Torecordagain

END

PLAY

• Use “dry” type head cleaning cassette

only. (Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully.

Excessive use of tape can shorten head life.

Cover the hole

with cellophane tape.

• If head clog symptoms persist, contact your

nearest servicenter by visiting our Web Site

(see p. 55).

Record/ Playback Time

Only use tapes with the

mark in this DECK.

Type of Video Cassette

Tape Speed

Setting

T60

T120

T160

2 Hours

1 Hour

2 Hours

40 Minutes

(Standard Play)

5 Hours

2 Hours 4 Hours

3 Hours 6 Hours

(Long Play)

20 Minutes

SLP

8 Hours

(SuperLongPlay)

Cleaning DECK

Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes

on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be

marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since

the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive,

antistatic cleaner and polisher.

Features for a Quality Picture (VCR)

Digital Auto Picture

Automatically controls the video output signal for less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for optimum picture quality.

Manual Tracking Control

(to reduce picture noise)

Use during Playback and Slow Motion mode to reduce picture noise.

Press CH (TRACKING)

on the remote control or on DECK until the picture clears up.

To return to Auto Tracking, press POWER off, then on again a few seconds later.

V-Lock Control (to reduce picture jitter)

In Still mode, CH (TRACKING) operate as a V-Lock control.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Power Source:

Power Consumption:

120 V AC, 60 Hz

Power On: Approx. 32 watts, Power Off: Approx. 4 watts

Video Signal:

EIA Standard NTSC color

Video Recording System: 4 rotary heads helical scanning system

Audio Track:

1 track (Normal), 2 channel (Hi-Fi Audio Sound)

Tuner:

Broadcast Channels:

CABLE Channels:

VHF 2 ~ 13, UHF 14 ~ 69

Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)

Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Input/Output Terminal:

Input Terminal:

Output Terminal:

Audio/Video Line Input/Output, RF Input/Output

Audio/Video Line Input (Front)

S-Video Output (DVD only), Component Video Output (DVD only)

Audio Output 2 (L), (R)

Operating Temperature:

Operating Humidity:

Weight:

5 °C ~ 40 °C (41 °F ~ 104 °F)

10 % ~ 75 %

4.9 kg (10.8 lbs).

430 (W) x 95.5 (H) x 344 (D) mm

16-15/16” (W) x 3-12/16” (H) x 13-9/16” (D) inch

Dimensions:

Discs Played

(1) DVD-Video Disc

5” (12 cm) single-sided single-layer

5” (12 cm) single-sided double-layer

5” (12 cm) double-sided double-layer (one layer per side)

3” (8 cm) single-sided single-layer

3” (8 cm) single-sided double-layer

3” (8 cm) double-sided double-layer (one layer per side)

5” (12 cm) disc

(2) Compact Disc

(CD-DA, Video CD)

3” (8 cm) disc

(CD-R/CD-RW, MP3, WMA, JPEG)

Digital Audio Output:

Pickup:

Digital Optical Connector

Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)

Laser power: CLASS II

Note: • Designs and specifications are subject to change without notice.

Definition of Terms (DVD)

Angle:

Some DVD discs feature scenes simultaneously shot from different angles.

The ANGLE button can be used to view the scene from different angles.

(ANGLE Indicator lights on DECK when a scene recorded at different

angles is detected.)

Chapter Number:Titles are subdivided into numbered sections. You can quickly search for

a favorite scene using these numbers.

DVD:

A high-density optical disc on which high-quality pictures and sound have

been digitally recorded. DVD incorporates new video compression

technology (MPEG II) and high-density recording technology which allow

entire movies to be recorded with incredible playback quality.

Playback Control:With Video CD (version 2.0), scenes or information may be selected for

viewing or listening from an interactive menu that appears on the TV screen.

Subtitles:

Time Number:

Written dialogue which appears at the bottom of the screen.

The elapsed play time from the start of a disc or title. Use to quickly find

scenes. (May not work with some discs.)

Title Number:

For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.

Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks

to be quickly located.

CD containing picture and sound with same quality level as video tape.

This DECK also supports Video CDs with playback control (version 2.0).

Video CD:

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093,

licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by method claims of

certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and

other rights owners. Use of this copyright protection technology must be authorized by Macrovision

Corporation, and is intended for home and other limited viewing uses only unless otherwise

authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Download from Www.Somanuals.com. All Manuals Search And Download.

Location of Controls

Bold:

VCR Function

Remote Control

Italic:

DVD Function

Bold Italic: VCR and DVD Functions

Normal:

Others

EJECT

INPUT

p. 35

OPEN

pp. 20, 22

TV mode

POWER

p. 28

CHANNEL

TRACKING V-LOCK

pp. 6, 21

NUMBER keys

VOLUME

p. 28

ACTION

ADD/DELETE

CLEAR

pp. 18, 47

pp. 19, 39, 46

SET

p. 38

VCR mode

SELECT

p. 28

STOP

DVD mode

pp. 20, 22

p. 28

FAST FORWARD

PLAY

SLOW+

pp. 20, 22

pp. 20, 23

SKIP

p. 23

REWIND

SLOW-

pp. 20, 23

TITLE

PAUSE

/STILL

p. 38

pp. 20, 23

ZOOM

COMMERCIAL SKIP

ZERO

p. 37

pp. 31, 32

SUB TITLE

p. 36

Virtual Surround Sound

ANGLE

ENTER

p. 37

pp. 23, 28

AUDIO (SAP / Hi-Fi)

TAPE POSITION

pp. 27, 36

VOLUME ADJUST

p. 34, 40

COUNTER RESET

p. 32

RETURN

VCR/TV

p. 21

pp. 22, 30

RECORD

p. 21

DISPLAY

p. 11, 41

PROGRAM

p. 24

SPEED

p. 21

EJECT button: When this button is pressed in VCR mode, the tape is ejected.

This button is inoperative if pressed during recording.

If pressed in DVD mode, the disc tray opens or closes.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

If the disc cannot be removed...

Front View of DECK

First, unplug DECK. Then, prepare a rigid

wire (e.g. an extended paper clip) and,

applying moderate force, insert it straight

into the hole at the base of the tray.

The tray will eject a little. Now, pull the tray

all the way out and remove the disc.

Bold:

Italic:

VCR Function

DVD Function

Bold Italic: VCR and DVD Functions

Normal: Others

STOP/EJECT

p. 20

FAST FORWARD/SEARCH

p. 20

PLAY

p. 20

Over 2 inches

Disc Tray

Over 2 inches

REWIND/SEARCH

p. 20

Cassette

Compartment

OPEN/CLOSE

p. 22

POWER

Audio/Video

Input Connector 2

(LINE 2) p. 35

PROGRESSIVE

p. 10

Multi Function

Display

CHANNEL

p. 11

PAUSE

p. 23

TRACKING/V-LOCK

pp. 6, 21

Remote

Sensor

SKIP

REC

p. 21

SKIP

p. 23

PLAY

p. 22

STOP

p. 22

Reset All Memory Functions

Use when moving DECK to new location, or if a mistake was made in the Initial

Setup section (return to Factory Setting).

• Make sure a tape is not inserted in the DECK.

Turn DECK Power on.

Press and hold both VCR PLAY

and CHANNEL

on the DECK for

more than 5 seconds.

• The power shuts off.

Do “Doing Initial Setup (Ready to

Play)” on page 16.

1 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Location of Controls (continued)

Bold:

VCR Function

Italic: DVD Function

Rear View of DECK

Bold Italic: VCR and DVD Functions

AC Power Plug

VHF/UHF Antenna Output Terminal

p.12

• While plugged into an AC outlet,

this DECK consumes 4 W of

electrical power in off mode.

VHF/UHF Antenna Input Terminal

p. 12

Component Video Output

Connector (Y, P^B, PR) (DVD Only)

p. 13

VideoOutput

Connector

p. 12

VideoInput

Connector

p. 35

•

S-Video Out

Audio Input

Connector (L/R)

p. 35

Optical Digital Audio

Output Connector

(DVD Only)

Audio Output 2

Connector (L/R)

p. 13

Connector

(DVD Only)

pp. 10, 13

p. 15

Audio Output 1

Connector (L/R)

p. 12

The following table shows the status of the output jacks when in VCR or DVD mode.

Video Output

Component

S-VIDEO OUT

N/A

Audio Out 1

Audio Out 2

Video Output

VCR

YES

N/A

YES

DVD

• PROG functions on the remote are not available when using Component Video Output

and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press

PROG.

Note

To enjoy PROGRESSIVE SCAN video

(1). Connect Component Video Output to the component video input terminals of a television.

(See p. 13.)

(2). When the PROGRESSIVE button is pressed, the ON lamp lights up (see p. 9) and the

PROGRESSIVE SCAN signal is output from the Component Video Output Connector.

Note

• The PROGRESSIVE button can be operated when the DECK is in DVD function mode.

• The screen may shift off-center when using progressive output. Please adjust the screen

position if this occurs. (Refer to your TV manual.)

• The DECK outputs video signals (not PROGRESSIVE SCAN) from the “VIDEO OUT” and “S-

VIDEO OUT” terminals when the ON lamp is lit.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Displays (On Screen & Multi Function)

On Screen Displays (VCR)

Function & Channel Displays

Blank Tape/ No Video Signal

Indications

When a function button

is pressed, e.g. PLAY,

CH 08

Whenever a blank section of a tape

comes up in Play mode, or when the

selected channel has no broadcast

signal with Weak Signal Display

Feature (p. 33) set to OFF, the TV

screen will turn solid blue.

or you change

channels, a 5-second

display appears.

Current Time

Channel

Function Status

VCR Status & Clock Displays

To display or remove

overlay at right,

CH 02

REC

12:00AM

0: 25

Counter

Rec Time Remaining

(OTR mode only,

see p. 21.)

TEREO

➛ press DISPLAY.

SAP

MONO

Tape Speed

(See p. 6.)

Broadcast Audio

Being Received

(See p. 26.)

Multi Function Display

DVD mode Indicator

Lights up when

VCR mode Indicator

Lights up when

DECK is DVD mode.

DECK is VCR mode.

DISC Indicator

Lights up when a disc

is inserted.

Tape Indicator

Lights up when a tape

DVD

VCR

is inserted.

REC

Hi - Fi

ANGLE

VCR REC Indicator

Lights up during

recording.

Hi-Fi Indicator

Lights up when Hi-Fi audio

is monitored in Play mode.

TIMER

ANGLE Indicator

Lights up when a scene

recorded at different

angles is detected.

AM/PM

Indicator

Timer Indicator

Lights up when DECK is set

for Timer Recording, or when

One Touch Recording (OTR)

is used. Flashes when Timer

Recording is set, but a tape

has not been inserted into

DECK and when a power

interruption occurs during

Timer Programming.

See p. 37. (DVD only).

Clock/ Status/ Channel/ Speed Display

Displays the current time. Briefly displays DECK

status when a function button is pressed. Briefly

displays the channel number, or “L1” or “L2” when

a channel or line input is selected. Briefly displays

the recording speed when SPEED is pressed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Basic Connections

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

• Connect DECK and TV with an RF Coaxial Cable

(supplied) or an AV Cable

(not supplied) as shown in the figure below.

I Cable Box DECK TV

I DECK TV

I DSS Receiver DECK TV

Antenna or Cable

DSS

Receiver

CableBox

OUT

1 Disconnect antenna or cable from TV

and connect to DECK.

2 Connect DECK to TV with RF Coaxial Cable.

DVD/VCR DECK

RF COAXIAL CABLE

IN FROM ANT.

IN1

OUT

VIDEO

AUDIO

VHF/

UHF

VHF/UHF

AUDIO IN VIDEO

OUT TO TV

AV CABLE (not supplied)

WARNING

When using “Nut type” RF coaxial cables, tighten with

fingers only. Overtightening may damage terminals.

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the

NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper

grounding and, in particular, specifies that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as practical.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Other Connections

YouCan

YouCannot

I With a Cable Box (DECK Cable Box TV)

• view any

(including

scrambled)

channel.

• record

scrambled

channels.

DVD/VCR DECK

ANT or CATV

IN FROM ANT.

IN1

OUT

IN OUT

Cable Box

IN OUT

• use Remote

AUDIO

VHF/

UHF

VHF/UHF

OUT TOTV

Control to select

channels without

using Multi-brand

control feature.

VIDEO

I Connect With Two Cable Boxes

YouCan

YouCannot

DVD/VCR DECK

ANT

• record and view

both scrambled

andunscrambled

channels if

additional

equipment is

added.

This connection

requires: two

converter boxes,

an A/B switch,

and a 2-way

splitter.

• view a channel

other than the

one selected

for any type of

recording.

IN FROM ANT.

IN1

OUT

Cable Box

CATV

IN OUT

VHF/UHF

OUTTOTV

• do a Timer

IN OUT

recording of a

channel unless

you select it on

the Cable Box.

2-Way Splitter

A/B Switch

AUDIO

Cable Box

OUT1

OUT2

VIDEO

VHF/

UHF

IN OUT

IN 1 IN 2

Connections For DVD Only (enjoying higher picture quality)

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT

or S-VIDEO mode).

If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to

S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV,

Notes

and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only

from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT

Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

• TV must have capability to accept and display a progressive scan signal to use

PROGRESSIVE mode. Consult your TV operating instructions.

From DECK’s

DVD/VCR DECK

A/V OUTPUT

COMPONENT

VIDEOOUT

DVD OUTPUT

AUDIOOUT2

AUDIO

VIDEO

P ^B

P R

S-VIDEO OUT

S-VIDEO

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections (continued)

Audio Connections

ReadyChecklist

Turn down the volume, then turn DECK, as well as other equipment to be connected,

off before proceeding with connection.

Do not block ventilation holes of any of the equipment and arrange them so that air can

circulate freely.

Read through the instructions before connecting other equipment.

Ensure that you observe the color coding when connecting audio and video cables.

I Connecting Amplifier (2ch stereo system) [Analog connection]

Speaker

Amplifier

DVD/VCR DECK

AUDIO IN

AUDIO OUT2

Enjoying digital audio output from the digital audio output connector

Notes on audio output from the optical digital audio output connector

Disc

DVD

Optical digital audio output from connector

Sound recording format

Dolby Digital bitstream (1-5.1 ch)

Dolby Digital

or PCM (48 kHz sampling/16 bit only)*¹

Linear PCM

(48/96 kHz 16/20/24bit)

Linear PCM (2ch)

(48 kHz sampling/16 bit only)*²

Bitstream or PCM (48 kHz sampling/16 bit only)*¹

DTS

Video CD

MPEG 1

Linear PCM

PCM (44.1 kHz sampling)

Linear PCM (44.1 kHz sampling)

MP3

Linear PCM (It depends on the MP3 file)

Linear PCM (It depends on the WMA file)

WMA

*1 The type of audio output from the connector can be selected by the Settings for DVD

Operation. (See p. 48.)

*2 Sound having 96 kHz sampling is converted into 48 kHz sampling when it is output

from the DECK’s optical digital audio output connector.

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories

Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel)

sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit,

DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from

the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from

titles with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic

Surround Sound Decoders please contact your local dealer.

Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942, 5,956,674,

5,974,380, 5,978,762 and other world-wide patents issued and pending. “DTS” is a registered

rights reserved.

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

I Connecting Amplifier (5.1 ch Surround system) [Digital connection]

DECK Dolby Digital Decoder Amplifier Speaker

DECK DTS (digital theater systems) Decoder Amplifier Speaker

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream

or DTS bitstream is output from the DECK OPTICAL digital audio output connector.

When DECK is connected to a Dolby Digital decoder or DTS decoder, you can

enjoy theater-quality audio in your home. [An optical digital audio cable (optional)

is required when an optional Dolby Digital decoder or DTS decoder is used.]

Notes on connecting an optical

digital audio cable (optional)

• Firmly connect the cable to the

connector.

Surround

Speaker

Surround

Speaker

[5.1ch Surround system]

Center

Speaker

DVD/VCR DECK

(Rear)

Decoder with

Dolby Digital /DTS

processing (optional)

Front

Speaker

Front

Speaker

To Optical

Amplifier

Digital Audio

Input Connector

Subwoofer

OpticalDigital

Audio Cable

(optional)

Caution for optical digital audio output connector:

• When connecting an amplifier (with an Optical Digital Input Connector) which does not

contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital”

and “PCM” at “dts” of the Settings for DVD Operation “AUDIO OUTPUT” (see p. 48).

Otherwise, any attempt to play DVDs may cause such a high level of noise that it may

be harmful to your ears and damage your speakers.

• When a Dolby Digital/DTS decoder is connected, please select “Bitstream” at “dts” or

“Dolby Digital” of the Settings for DVD Operation “AUDIO OUTPUT”.

If “PCM” is selected, there will be stereo sound. (See p. 48).

• Video CDs and CDs can be played as usual.

Note:

• Some DTS decoders which do not support DVD-DTS interface may not work properly with

DECK.

Download from Www.Somanuals.com. All Manuals Search And Download.

Initial Setup for Basic Connections (Ready to Play)

Before doing Initial Setup

Turn TV on.

See connections

RF Coaxial Cable Connection and

AV Cable Connection on p. 12.

2 _{<RF Coaxial Cable Connection>}

Set TV to channel 3.

Set TV to VIDEO.

[DECK ➛ TV]

• Go to “Doing Initial Setup (Ready to Play).” (See below.)

[Cable Box ➛ DECK ➛ TV], [DSS ➛ DECK ➛ TV]

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel

in your time zone.

• If you use a DSS Receiver, it must be turned off.

Doing Initial Setup (Ready to Play)

Press VCR on remote for VCR mode.

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel

and clock set starts.

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to

channel 3, try switching it to channel 4.

• To change VCR’s output channel, please refer to “VCR’s Output Channel” on p. 19.

Plugging the AC Power Plug into

an AC outlet

Notes

CH AUTO SET PROCEEDING

• Function buttons are inoperative during Initial Setup.

CANCEL : STOP

• To remove a cassette during Auto Set, press EJECT on

the remote or STOP/EJECT twice on the DECK.

In this case, settings must be made manually. (See p. 18.)

• Depending on conditions, Auto Clock Set may take longer

than 30 minutes. If so, press STOP to stop setup and

perform settings manually. (See p. 18.)

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

Continued on next page...

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Settings are made automatically.

When setup is done, this screen appears.

EJECT

2003 SUN

20P

SETT

AUTO CLOCK SET

PLETED

CH 10

COM

If “AUTO CLOCK SET IS INCOMPLETE”

appears, manually set clock. See below.

ACTION

SELECT

AUTO CLOCK SET IS

NCOMPLETE

PLEASE SET CLOCK BY

SET

PRESSING ACT ON KEY

VCR

Manual Clock Set

If Auto Clock Set was incomplete.

Press ACTION* on remote to display

CLOCK screen.

SET

CLOCK

----------------^D--^S-^T-^:O-^N--

LEC

ONTH

SELE

SET

ACT

EXIT

Press

to select the month and SET to

STOP

set. In the same manner, select and set the

date, year, time, and DST (Daylight Saving

Time).

SET

CLOCK

2003 SUN

ST:

----------------^D----^O--^N-

SET CO

: SET

ACT

BACK :

ART

Press ACTION to start clock and exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Reset Language, Channels, Clock,

• PROGRAM functions are not available

Press ACTION*

to display MENU.

SET UP VCR

when using COMPONENT Video Output

and S-VIDEO OUT. Please set TV to

either RF INPUT or VIDEO INPUT, and

then press PROGRAM.

SET CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT :

EXIT

SET:SET

: ACTION

Language

Channels

Clock

1) Press

to select

1) Press

to select

1) Press

to select

“SET UP CHANNEL,”

language item.

“SET CLOCK,” and

and press SET.

press SET.

SET UP VCR

SET CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT :

EXIT : ACTION

SET:SET

SELECT :

SET : SET

SELECT :

SET : SET

EXIT

: ACTION

EXIT

: ACTION

2) Press

to select

2) Press SET repeatedly to

change language item as

shown below.

2) Press

to select

“MANUAL,” and press SET.

(For Auto Clock Set, select

“AUTO CLOCK SET.”)

“ANTENNA,” then

press SET to set your

antenna system

PREPARAR VCR

FIJAR RELOJ

FIJAR CANAL

LANGUE/LANGUAGE:ESPAÑOL

CANAL DE SALIDA : 3

(“TV” or “CABLE.”)

SET

CLOCK

SET UP CH

ANNEL

ANTENN CABLE

AUT

SET

JUS

SET

NUAL

SIGNAL DISPLAY : OFF

ELEGIR :

SALIR

FIJAR : SET

: ACTION

SELE

SET SET

EXIT

ACT

SELE

SET SET

EXIT

ACT

For Spanish

(“TIME ZONE ADJUST”

appears only when auto

clock is set.)

3) Press

to select

REGLAGE MAGNETOSCOPE

REGLAGE HORLOGE

REGLAGE CANAL

“AUTO SET,” then

LANGUAGE/IDIOMA:FRANÇAIS

CA SORTIE : 3

press SET.

SET

CLOCK

• If you use a Cable Box,

set it to the PBS channel

in your time zone.

2003 SUN 12

SEL.

REGLER:SET

ST:

----------------^D----^O--^N-

QUITTER : ACTION

SELECT

HOUR

For French

SELE

SET

ACT

BACK :

EXIT

SET UP VCR

SET CLOCK

3) Press

and to

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

CH AUTO SET PROCEEDING

CANCEL : STOP

select, then set the date,

time, and DST (Daylight

Saving Time).

SELECT :

EXIT : ACTION

SET:SET

• After Channel Auto Set

is finished, Auto Clock

Set will be performed.

4) Press ACTION to start

Clock and exit this

mode.

For English

3) Press ACTION to exit.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

VCR’s Output Channel

*Important: If a remote control button does not work

when pressed, press the VCR button

POWER

on the remote and try the button again.

NUMBER

keys

ADD/DLT

SELECT

Time Zone Adjust

VCR’s Output

Channel

(Only when Auto Clock is set.)

1) Press

to select

“VCR’S OUTPUT CH.,”

and press SET.

1) Press

to select

“SET CLOCK,” and

SET

press SET.

SET UP VCR

VCR

SET CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

ACTION

SELECT :

SET : SET

SELECT :

SET : SET

EXIT

: ACTION

EXIT

: ACTION

2) Press SET.

2) Press

to select

“TIME ZONE ADJUST,”

Add or Delete a Channel

I F YOU PRESS ACT

KEY, VCR’ S UTPUT CH

ITCHES CH

To add channel:

Select channel with NUMBER keys

and press ADD/DLT.

SET

AUT

LOC

SET

ANUAL

JUS

HANNEL 08 ADDED

3) Press ACTION.

SELE

SET SET

EXIT

ACT

To delete channel:

Select channel with CH

NUMBER keys and press ADD/DLT.

PLEASE TUNE

YOUR TV TO

and press SET to

subtract or add hour(s)

as necessary.

CHANNEL 08 DE

TED

After 3 seconds

3) Press ACTION twice.

• “TIME ZONE ADJUST”

returns to “0” if clock is

set manually.

SET UP VCR

SET CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:4

DST (Daylight Saving Time)

SELECT :

EXIT : ACTION

SET : SET

DECK auto adjusts clock for DST.

(p. 17.)

• To Make Corrections,

repeat steps 1) ~ 3).

Spring (First Sunday in April)

DST:ON ➛ Sets clock ahead one hour.

Autumn (Last Sunday in October)

DST:ON ➛ Turns clock back one hour.

• If your area does not observe

Daylight Saving Time, select

DST:OFF.

• Keep these time changes in mind

when programming DECK for

timer recordings.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback/ Record on a Tape

EJECT

Ready Checklist

All connections are made (pp. 12 ~ 15).

TV and DECK are plugged in.

TV is on and tuned to CH 3, 4, or VIDEO.

Remote is in VCR mode. (Press VCR.)

Playback a Tape

Insert a tape.

1 _{• DECK power comes on. If Auto VCR/TV (see}

VCR

p.32) is set to “OFF,” press VCR/TV on the

remote to be VCR mode.

DVD

PLAY

STOP

Press PLAY* to play a tape.

REW/

SLOW-

PAUSE/

STILL

FF/

SLOW+

• If tape has no rec. tab (p. 6), auto play begins.

Special Features During Play

Forward/Reverse Scene Search

➛ Press FF/SLOW+ or REW/SLOW-.

➛ Press PLAY to release.

After search has begun, each additional press of

FF or REW changes speed as shown below.

VCR/TV

REC

SPEED

[SLP] : Approx. 21X ↔ Approx. 9X

[LP] : Approx. 9X ↔ Approx. 7X

[SP] : Approx. 7X ↔ Approx. 3X

If at 21X, 9X, or 7X speed the picture is

interrupted, change speed to 9X, 7X, or 3X.

Notes

• These features work best in SP or SLP mode.

• The sound will be muted.

• To reduce picture noise, see “Manual Tracking

Control” on p. 6.

• After DECK is in Still or Slow mode for 3 minutes,

it will switch to Stop mode automatically to

protect the tape and the video head.

Notes

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary

depending on current tape position.

Still (Freeze) Picture

➛ Press PAUSE/STILL.

➛ Press PLAY to release.

Frame by Frame Picture

➛ Press PAUSE/STILL in Still mode.

➛ Press PLAY to release.

Playback using DECK buttons

2_{Press PLAY.}1_{Insert a tape.}

Slow Motion Picture

➛ Press FF/SLOW+ (increase speed) or

REW/SLOW- (decrease speed) in Still

mode.

➛ Press PLAY to release.

Press STOP to stop a tape.

Multi Function Display

Press REW/SLOW- or FF/SLOW+ in Stop

mode to rewind or fast forward a tape.

Press STOP/EJECT to stop

and/ or eject a tape.

Press EJECT on remote, or STOP/EJECT

on DECK to eject a tape.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Record on aTape

This video recorder, equipped with HQ

(High Quality) system, is compatible

with existing VHS equipment. Only use

Insert a tape with a record tab (p. 6).

• DECK power comes on. If Auto VCR/TV (see p.32)

is set to “OFF,” press VCR/TV on the remote to be

VCR mode.

tapes with the

mark. Only tapes

tested and inspected for use in 2, 4, 6,

and 8 hour machines are

recommended.

Press CH

, or NUMBER keys

to select the channel.

• For “LINE” input, see p. 35.

• If channel is over 100, press 100 key then press

the remaining 2 digits.

Note

Remove loose or peeling

labels from tapes to prevent

tape jam.

Press SPEED

to select the record speed (p. 6).

SP = Standard Play

SLP = Super Long Play

• Speed appears on-screen and on Multi Function Display.

LP = Long Play

Press REC

to start recording.

(The VCR REC indicator lights up on Multi Function

Display),

• To edit out unwanted scenes, press PAUSE/STILL

to pause, and again to resume recording.

• You cannot view another channel during recording.

Press STOP

to stop recording.

One Touch Recording (recording in progress),

Normal Rec

4:00 3:00

0:30

2:00

1:00

1:30

➛

Press REC repeatedly to set the recording length

(30 min. ~ 4 hours).

• DECK shuts off after the preset record length.

Record one station, watch another,

➛

press VCR/TV on the remote

(change to TV mode),

Record using DECK buttons

➛

select channels at TV (recording continues).

Select Channels at DECK (In STOP or

Insert a tape.

Press REC

to start

Recording.

REC. PAUSE mode),

➛

press VCR/TV on the remote

(change to TV mode),

➛

select channels at DECK.

Play a disc while recording a tape.

➛

insert a disc during recording,

press DVD, and then press PLAY.

Multi Function Display

Notes

Select

Channel.

• It is not possible to record from DVD/ Video

CD/ CD to VHS tape using DECK.

• Watching one channel and recording another

is not possible when using Cable Box or

DSS Receiver.

Press STOP/EJECT to stop.

• After 5 minutes in Pause mode, DECK stops to

protect a tape and video heads.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic DVD Operation

Press POWER* on the remote or DECK.

Ready Checklist

All connections are made. (pp. 12 ~ 15)

DECK is plugged in.

If DECK is connected to an audio amplifier,

turn the stereo system’s power on.

Press DVD to select DVD mode.

• If a disc is already inserted, go to step 4.

(Depending on the disc, playback may

start automatically.)

Press OPEN/CLOSE,

OPEN/

3 _{and then place a disc into the disc tray.}

POWER

SELECT

• Hold disc by its edges

only (p. 4) with printed

side up and use guides to

place into tray.

NUMBER

keys

Use

3”(8 cm)

5” (12 cm) disc.

Press PLAY to start playing.

DVD

4 _{Disc tray closes automatically.}

• You may also close tray by

pressing OPEN/CLOSE.

• Data reading time differs with

each disc.

SET

PLAY

SKIP

STOP

READING

REW/

SKIP

TITLE

SLOW-

TITLE MENU

FF/

SLOW+

If an interactive DVD*¹or

a Video CD with playback

control*²is used and TITLE

MENU appears, go to step 5.

VSS

Dogs Castles

Birds

PAUSE/

STILL

Lovers

RETURN

Press

TITLE MENU

NUMBER keys (see

below) to select title,

and press SET or

Dogs Castles

Operation using DECK buttons

3, 7 Press

Birds

Lovers

Dogs

PLAY to start playing.

• “Pressing SET or PLAY”

is not necessary when

using NUMBER keys.

of the world

OPEN/CLOSE.

1_Press

POWER

4 _{Press PLAY.}

Using NUMBER keys starts playing automatically.

The number of available titles varies with each disc.

3Insert a disc.

1 digit number

2 digit number

3 digit number

1 ••• 1

12 ••• 10 1 2

123 •••100 1 2 3

<Input

Example>

Press SKIP

menu screen.

| or |

to go to next or previous

• SKIP function not available with all discs.

Please refer to disc jacket for operation information.

6 _{Press STOP.}

To return to menu (play stops)

Press TITLE, MENU, or RETURN. (DVD)

Press RETURN. (Video CD)

*¹Interactive DVD...

May include multiple camera angles,

stories, etc.

*²Video CD with playback control...

Particular scenes or information can be

interactively selected from a menu that

appears on the screen.

Press STOP to stop playing.

Press OPEN/CLOSE to eject the disc.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

I Forward/Reverse Scene Search

V.S.S. (VirtualSurroundSound)

Press FF/SLOW+ or REW/SLOW-

Enjoy a surround-like effect if you are

using two front speakers only. The effect

is broadened and sound seems to come

from virtual speakers on either side if the

disc has surround signals recorded on it.

during play.

Press PLAY to release.

• Starting forward/reverse search during play

started from menu on Video CDs may recall menu.

• Search speed, slow at first, increases with each

additional press of the button up to 5 levels.

Press VSS in DVD mode.

• The Surround sound effects can be

changed by pressing VSS repeatedly as

shown by the figure below.

I Forward/Reverse Chapter/Track Skip

Press SKIP

| or |

SKIP during play.

VSS1

Each press skips a chapter (DVD) or

track (Video CD/CD).

VSS OFF

VSS2

VSS OFF (default)

VSS3

• Pressing |

SKIP once midway through a

Note

chapter/track returns to the start of that

chapter/track. Each additional press skips

back one chapter/track.

• Surround sound effects is available in DVD

mode only.

• Turn off the surround effects on the other

equipment.

• V.S.S. will not work, or will have less effect,

with some discs.

• Turn V.S.S. off if it causes distortion.

• Sound will only come from the two front

speakers if V.S.S. is on.

• Pressing SKIP

| or |

during play started

from menu on Video CDs may recall menu.

Current playback position

Chapter/Track Chapter/Track Chapter/Track Chapter/Track

Reverse Skip

Forward Skip

Resume Function

IStill Picture or Pause

Press PAUSE/STILL during play.

DECK memorizes the point where STOP is

pressed (STOP

is displayed on screen).

Press PLAY to resume play from this point.

Pressing STOP again or opening the tray

cancels RESUME, however, RESUME is not

canceled when power is turned off and on.

• RESUME works only with discs for which

elapsed play time is displayed during play.

Press PLAY to release.

• DVD/Video CD : DECK will enter still picture mode.

• CD : DECK will enter pause mode.

I Frame by Frame Picture

(DVD/Video CD)

Press PAUSE/STILL in still mode.

Press PLAY to release.

• Each press advances picture one frame.

• Hold button down for consecutive frame advance.

• Whether pictures are advanced by “FRAME” or

“FIELD” is selected automatically. (See p. 49)

Enjoy Video CDs featuring

playback control without using

menus (Video CDs only)

1. Do steps 1-4 (previous page).

When menu appears, press STOP.

2. Press NUMBER keys to select desired

track (play begins).

ISlow Motion Picture (DVD/Video CD)

Press FF/SLOW+ or REW/SLOW-

in still mode.

•

Check disc for track numbers.

Press “1” to start at beginning of disc.

Press PLAY to release.

To Resume Menu use,

• Slow motion speed, slow at first, is increased

with each additional press of the button up to

5 levels.

Press STOP and press PLAY, then the

menu will be displayed.

Now, go to step 5 (previous page).

• Reverse slow motion is not available for Video CDs.

Notes

• Please read the disc jacket for operation

information.

Auto-Power Off Function

Power turns off after DECK has been in

Stop mode (DVD) for about 5 minutes.

• If a single sided disc is placed in upside

down, “THIS TYPE OF DISC CANNOT BE

PLAYED. PLEASE INSERT A DIFFERENT

DISC” is displayed.

• Remove disc and press DECK POWER off

when not in use.

• When

appears on the screen while a button

is being operated, it means that the

corresponding operation is prohibited by DECK

or the disc.

• Disc continues to rotate with menu displayed

even after play is done.

Press STOP to clear menu display when

finished with menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Timer Recording

Ready Checklist

All connections are made (pp. 12 ~ 15).

TV and DECK are plugged in.

Clock set correctly. (p. 18)

Tape has rec.tab. (p. 6)

Remote is in VCR mode. (Press VCR.)

POWER

Sufficient tape remaining for recording time.

Press PROG*

to display Program.

1) To set record DATE,

press to select:

DATE

START

13 SUN

--:-- --:-- --

ADD/DLT

SELECT

-^O-^D-^A-^Y-----------------^S-^L-^P-

1~31= one time, or

DAILY= MON~ FRI, or

WEEKLY= same time

each week and

START

ATE

SELE

SET

T :

SET

PROG

END

SET

VCR

press SET.

Example

Today

• See selection order left.

2) To set remaining items,

press

DAILY

WEEKLY

(SUN)

SELECT

Selection Order

to select and

press SET

WEEKLY

(MON)

to set START/ STOP times,

CH (channel) or LINE

input (p. 35), and tape

speed (SP, LP, SLP).

WEEKLY

(SAT)

PROG

Press PROG

to end programming.

VCR REC Indicator

To Enter More Programs,

press

DT STA

CH SPD

13 10

VCR mode Indicator

-- --

-- -- --

to select and

Multi Function Display

press SET

SELECT 1-8

NTER

EXIT

ADD/DLT

to set an unused program

number, and then repeat

step 2.

: SET

PROG

VCR

REC

Hi - Fi

TIMER

Press PROG

to exit.

TIMER Indicator

• The “Timer” Indicator lights up on DECK.

• You can do Timer Recording with the power on or off.

• “TIMER REC WILL START SOON” appears on-screen for 2 minutes

before Timer Recording starts. If DECK is in DVD mode, no message

appears, but the VCR REC Indicator, the VCR mode indicator and

“REC” will flash on Multi function Display.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Review, Replace or Clear Program Contents:

(Recording is not in progress)

Press PROG

To cancel a Timer

to display Program List.

Recording in progress...

Hold down STOP in VCR mode for

a few seconds to cancel the Timer

Recording.

(The “TIMER” Indicator goes out

on Multi Function Display.)

Press

DT STA

CH SPD

08 SP

02 SP

10 SP

L1 LP

to select number and

press SET

to display.

ANC

ADD/DLT

SELECT 1-8 :

ENTER : SET

EXIT

: PROG

• Any future daily or weekly recording

will be performed as programmed.

To Replace program...

DATE

TART

TOP

Repeat Step 2 (p. 24)

to set new programs.

SUN

00A 12

00A 08

--^O--^D------------------------------------

START

DATE

SELE

SET

CT :

SET

PROG

BACK :

END

To Clear program...

DT STA

CH SPD

Press ADD/DLT.

-- --

-- -- -- -- --

02 SP

10 SP

L1 LP

ADD/DLT

SELECT 1-8 :

ENTER : SET

EXIT

: PROG

Press PROG

to end the programming.

Notes

• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to

the Cable Box input channel and Cable Box must be manually set to the desired

channel. Cable Box power must be left on.

• 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER

REC” appears and Timer Indicator flashes.

Be sure a cassette with record tab is loaded and DECK is in Stop mode.

• If a power interruption occurs while programming the timer, the timer program(s) may be

canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION”

appears on-screen, please re-enter the timer programs.

• If the start time for Timer Recording comes up during recording and playing back,

Timer Recording will not be performed.

Important notes when using DSS Receiver

• When recording programs via DSS Receiver, DSS Receiver must be left on.

• When recording programs via an antenna or cable, DSS Receiver must be turned off.

Download from Www.Somanuals.com. All Manuals Search And Download.

MTS Broadcast/ VHS Hi-Fi Stereo System

Connection

Make the Audio/Video Connection as shown on pp. 12 ~ 15.

• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.

Receivable Broadcast Types

The following are possible audio broadcast types and on-

screen displays.

The signal being received is indicated with an “ ” mark

while the selected audio mode is indicated with an arrow.

To display the broadcast signal being received,

➛ press DISPLAY*.

MTS Stereo and SAP broadcast

CH 02

STOP

12:00

STEREO

SAP

Multi-channel Television Sound

Stereo (main language) and

Secondary Audio Program (sub

language) broadcasts are being

received simultaneously.

ONO

Select STEREO or SAP audio mode.

AUDIO

(SAP/Hi-Fi)

MTS Stereo broadcast

CH 02

STOP

DISPLAY

STEREO

SAP

Multi-channel Television Sound

Stereo broadcast. Select STEREO

audio mode.

• If stereo broadcast is weak and

display flickers, select MONO audio

mode for possible better results.

MONO

SAP broadcast

CH 02

STOP

STEREO

SAP

Secondary Audio Program (sub

language) broadcast. Select SAP

audio mode for the sub language.

ONO

Equipped with

^®-TV

Noise Reduction for

true MTS reproduction.

^®-TV Noise

Reduction is required

for good stereo

MONO broadcast

CH 02

STOP

12:00AM

separation and audio

STEREO

SAP

Normal monaural sound broadcast.

fidelity.

is a

ONO

registered trademark,

and is licensed by

Technology Licensing.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Audio Mode for Recording

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

(Display disappears after 5 seconds.)

Press AUDIO (SAP/Hi-Fi) repeatedly

to select desired mode.

STEREO

SAP

MONO

• Refer to “Receivable Broadcast Types” on p. 26.

• Arrow indicates selection.

Make a recording.

See p. 21.

Audio Mode for Playback

Start playback.

See p. 20.

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

Press AUDIO (SAP/Hi-Fi) repeatedly

to select desired mode.

IFI : L

IFI

ORMAL

• Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo

recordings in stereo sound.

Select “NORMAL” for monaural sound.

• Display disappears after 5 seconds.

• Arrow indicates

selection.

Notes

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard

stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to

a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.

• Hi-Fi and normal audio playback volume level may differ.

Download from Www.Somanuals.com. All Manuals Search And Download.

Multi-Brand Control Feature

Multi-Brand Control Setup

The Remote Control can be set to control some TV functions.

POWER

Find your TV Brand Code Number on the

following page.

Set up for TV control,

➛ hold down TV button,

➛ enter code with NUMBER keys.

• If code number is 100 or greater,

➛ e.g., press 1 - 0 - 2 for 102.

NUMBER

keys

Confirm code entry,

➛ press POWER to turn selected unit on or off.

• See table below for controllable functions in each mode.

DVD

Notes

VCR

• Repeat setup after remote battery replacement.

• Remote will not control every TV made by the

manufacturer listed. If you get no response, your particular

unit cannot be controlled. There are NO additional codes

for the products listed. If your product is not listed, then the

remote is not compatible with that product.

ENTER

Using Multi-Brand Control

After remote is set up, you can select VCR, DVD, or TV for the

desired function.

Press VCR, DVD, or TV on the remote.

(Table below shows available remote buttons for each mode.)

Unit

DVD/VCR

Mode

DVD/VCR

All

VOL

+/-

POWER, INPUT,

NUMBER keys, ENTER,

CH , VOL

EJECT/OPEN/CLOSE *,

DISPLAY, PLAY, STOP,

FF/SLOW+, REW/SLOW-,

VCR/TV, PAUSE/STILL, SKIP,

AUDIO, CM/ZERO,

+/-

TAPE POSITION,

COUNTER RESET, SPEED,

REC

* Bold: VCR Function

Bold Italic: VCR and DVD Functions

Normal: TV

Italic: DVD Function

Notes

• Not all functions listed may be controllable.

• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys

for channel selection.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

TV Brand Code Numbers

Panasonic ....................... 01, 02

Quasar ............................ 01, 02

RCA ....................................... 03

GE ......................................... 03

Zenith .................................... 04

Magnavox .............................. 05

JVC ........................................ 11

Hitachi ................................... 12

Mitsubishi ........................ 07, 13

Samsung ............................... 14

Gold Star ................... 15, 16, 17

Sylvania ................................ 05

Sharp ............................... 06, 07

Sony ...................................... 08

Toshiba ................................. 09

Sanyo .................................... 10

Fisher .................................... 10

Important Notes

• Some manufacturers use several codes for one brand. If the first code entered fails, try the

next one listed.

• Some TV brands require you to turn on the power manually.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tape Operation

Search System

For each recording, an invisible index mark is placed on the tape. A program index and

information are also included for timer recordings. These marks are used to access or

scan recordings.

Program End Search

Index Search

Locates end point of recording for continuity.

Press SEARCH*

to display SEARCH

in Stop or Play

mode, and then

press NUMBER

keys

to select recording

number.

• To calculate

number, see below.

INDEX SEARCH

ENTER INDEX NUMBER :1

USING 9 KEYS

Press SEARCH twice

to display SEARCH in Stop or Play

FORWARD SEARCH :FF

REVERSE SEARCH :REW

NEXT :SEARCH

mode.

EXIT :STOP

Press FF/SLOW+

PROGRAM END SEARCH

on the remote to

start PROGRAM

END SEARCH.

SEARCH START : FF

Press FF/SLOW+

or REW/SLOW- on

the remote to start

search.

EXIT :SEARCH

• To cancel, press

PLAY or STOP.

Examples of Program End Search.

Fig.1

INDEX SEARCH

Play begins at

search end.

To search forward

or back 1 index,

press FF/SLOW+ or

REW/SLOW- on the

remote while

Program 1

Program 2 or BLANK

the current tape position

Press SEARCH button

FORWARD SEARCH : FF

REVERSE SEARCH : REW

EndPoint

Fig.2

screen left is

displayed (10 sec.).

Program 1

BLANK

Program

the current tape position

Press SEARCH button

• To cancel, press

PLAY or STOP.

End Point

Fig.3

To Calculate Index Number

the current tape position

Press SEARCH button

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

Program 1

BLANK

Program

If search exceeds

a few seconds in

BLANK area.

EndPoint

Example 2:

Uponlocatingendpoint,

To go to rec. 6 from rec. 2, enter 4 and press FF.

➛ search continues 7 sec. past end point,

➛ tape rewinds to 10 sec. before end point,

➛ tape plays to end point and stops.

NOTE: indicates start points of each recording.

Note

• If Index Search is started very close to an

index mark, that index mark may not be

counted in the search.

• If Program End Search is started very close to

an index mark, that mark may be skipped over.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Auto Operation Functions

Auto Play

Insert a tape ➛ Power comes on,

➛ Play starts if there is no record tab

(see p. 6).

Auto Rewind

Play

Fast Forward

➛ Tape end ➛ Rewind

Play Auto Eject

(Repeat Play must be off)

Play ➛ Tape end ➛ Rewind

➛ Tape ejects if set some programs.

NUMBER

keys

STOP

PLAY

Commercial Skip

REW/SLOW-

FF/SLOW+

CM/ZERO

VCR fast forwards (skips) over 1~3 minutes

of recorded tape.

Press CM/ZERO in Play mode.

• The skip time can be changed by

pressing CM/ZERO repeatedly as

shown by the figure below.

PLAY

1st Press

2nd Press

3rd Press

1 min Skip

2 min Skip

3 min Skip

• No indication appears on-screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tape Operation (continued)

Repeat Play

VCR/TV Selector Feature

Set to playback a recording over and over.

The VCR/TV selection can be set to

auto or manual.

Press ACTION*

to display MENU.

Press ACTION

to display MENU.

SET UP VCR

SET CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

Press

to select “SET UP VCR,” and

Press

to select

“SET UP

VCR,” and

SET UP VCR

SET CLOCK

press SET.

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

SELECT :

EXIT : ACTION

SET : SET

VCR’S OUTPUT CH:3

SELECT :

SET : SET

EXIT

: ACTION

press SET.

Press

SET UP

REPEAT PLAY

RE OTE ARN

AUT

SHU

OFF

to select “REPEAT PLAY,”

and press SET

OFF

AUT

VCR/TV

OFF

Press

SET UP

REPEAT PLAY

RE OTE ARN

SHU

VCR/TV

OFF

to set “ON” or “OFF.”

to select

AUT

OFF

SELE

SET: SET

AUTO

END

ACT

“AUTO VCR/

TV,” and

press SET

to set “ON”

or “OFF.”

• Play repeats at tape end or if unrecorded portion

over 30 sec. is detected.

SELECT

SET: SET

END

ACT

Press ACTION twice

to return to normal screen.

• OFF(Manual):You select “VCR” or

“TV” mode using the

VCR/TV button on the

remote.

Note

• For repeat play in DVD mode, see page 42.

• ON(Auto):

“VCR” mode is

automatically set when

VCR is turned on, or in

Play mode.

Zero Search

To quickly return to a specified tape location.

Press DISPLAY during play

Press ACTION

to return to normal screen.

1_{to display Counter.}

PLAY

12:00AM

Press COUNTER RESET

at desired position to reset

to “0:00:00”.

Note

• For more on VCR/TV selection, see

“Record one station, watch another”

and “Select channels at DECK”

sections (see p. 21).

Continue to record, playback etc.

Press STOP.

REW

12:30

CH 02

Press CM/ZERO in Stop mode

to start Zero Search.

STOP

12:31

CH 02

• DECK will go into FF or REW mode and stop

at the last point the Counter was set to 0:00:00.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

*Important: If a remote control button does not work

when pressed, press the VCR button

Special VCR Features

on the remote and try the button again.

Weak Signal Display Feature

When “ON,” picture is displayed regardless of signal

strength.

Press ACTION

1 _{to display MENU.}

Press

ACTION

SELECT

SET UP VCR

SET CLOCK

to select “SET UP

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

CHANNEL,” and

press SET.

SELECT :

EXIT : ACTION

SET : SET

SET

SET UP CH

ANNEL

Press

ANTENN ABLE

STOP

AUT

SET

to select “WEAK SIGNAL

DISPLAY,” and

press SET

WEA

SIGNAL DISPLAY:OFF

CM/ZERO

SELE

EXIT

SET: SET

ACT

to set “ON” or “OFF.”

COUNTER

RESET

• ON: Picture is displayed regardless of signal

condition, and may not always be clearly visible.

DISPLAY

OFF: Screen turns solid blue when signal is weak or

non-existent.

• Selecting ON has no effect on connected equipment

VCR Lock Feature

with blue back feature.

When set to ON, all operations

except for timer record and tape

eject are prohibited. Useful for

households with small children.

Press ACTION twice

to return to normal screen.

To turn on, hold down REC on

DECK in Stop mode with no

tape inserted for 7 seconds.

(Please ignore “NO CASSETTE”

warning.)

Auto Shut-Off Feature

The power shuts off at a preset time.

Press ACTION

1 _{to display MENU.}

Press

SET UP VCR

SET CLOCK

SET UP CHANNEL

to select “SET UP VCR,” and

LOCK

ACTIVATED

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

press SET.

SELECT :

EXIT : ACTION

SET : SET

To turn off, repeat above.

SET UP

REPEAT PLAY

RE OTE ARN

SHU OFF

VCR/TV

Press

to select “AUTO SHUT-OFF.”

Press SET repeatedly to

change shutoff time as

AUT

T-

OFF

AUT

SELECT

SET SET

EXIT

ACT

shown below.

• VCR Lock cancels in 24 hours if

clock is set.

2 Hours

4 Hours

OFF

6 Hours

Press ACTION twice

4 _{to return to normal screen.}

REC

Note

• The shut-off countdown will not function during Play or

Record.

Download from Www.Somanuals.com. All Manuals Search And Download.

Special VCR Features (continued)

*Important: If a remote control button does not work

Remote Warning Feature

If Multi-brand feature is used (p. 28), and this feature is

set to on, a warning appears whenever an invalid key

is pressed in TV mode.

when pressed, press the VCR button

on the remote and try the button again.

INPUT

Press ACTION*

to display MENU.

SET UP VCR

SET CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

Press

to select “SET UP VCR,”

and

ACTION

SELECT

press SET.

SELECT :

EXIT : ACTION

SET : SET

Press

SET UP

VCR

SET

REPEAT PLAY

RE OTE ARN

SHU OFF

VCR/TV

to select

STOP

AUT

T-

OFF

“REMOTE WARNING,” and

press SET

to set “ON” or “OFF.”

AUT

PAUSE/

STILL

SELE

EXIT

SET: SET

ACT

• If “OFF,” remote warning will not appear

when invalid key is pressed.

TapePosition

REC

Press ACTION twice

to return to normal screen.

Tape Position and Tape Status Feature

To find out the present tape position and amount of tape remaining.

Tape position is displayed for VHS-C type Cassettes, tapes

under 30 minute long, and some other tapes, but the

position is not correct.

Press TAPE POS.

to detect current tape position.

• “DETECTING TAPE POSITION” is displayed

DETECTING TAPE POSITION

only when a cassette is first inserted, and it

takes several seconds for correct tape

position to appear.

• The present tape position indication and

amount of tape remaining (according to

tape speed) is displayed.

R 120 MIN.

• Tape remaining time display may not be

precise.

BEG

END

Press TAPE POS.

to return to normal screen.

Note

This function cannot display exact amount of tape remaining for

tapes 30 minutes or less, or for tapes over 120 minutes in length.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

CopyingYour Tapes (Dubbing)

Connection

VCR/ Camcorder (Hi-Fi)

DVD/VCR DECK

Front of DECK

IN FROM ANT.

VIDEO IN 2

L-AUDIO IN2-R

IN1

OUT

VIDEO

AUDIO

VIDEO

VHF/

UHF

VHF/UHF

OUTTOTV

(Audio/Video In Terminals

on the front of DECK are

available)

AUDIO

Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK.

To monitor the dubbing, also connect TV as shown.

Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R”

AUDIO IN terminals on DECK.

In place of Playing VCR, you can use other equipment, such as a Camcorder.

Simply connect the unit’s Audio/Video outputs to DECK.

Playing (Source) VCR

Recording (Editing) DECK

Insert a pre-recorded tape.

Insert a blank tape with record tab.

Press INPUT to set DECK Input mode to

LINE for Video Input.

(See “Selecting the Input Mode” below.)

Press REC, then PAUSE/STILL

immediately to enter REC/PAUSE

mode.

Press PLAY, then PAUSE/STILL

immediately to enter PLAY/PAUSE

mode.

The operation of steps 4 and 5 must be done on the

playing and recording VCRs at the same time.

Press PLAY to start dubbing.

Press PAUSE/STILL to start dubbing.

Playing VCR starts playback.

DECK starts recording.

Press STOP to stop dubbing.

Selecting the Input Mode

To Monitor Dubbing on TV

1 Turn TV on and tune to the Recording

Method 1: Press INPUT repeatedly.

VCR channel (CH 3 or CH 4).

Channel Number ↔ LINE1 ↔ LINE2

Method 2: Press CH

2 If Auto VCR/TV (see p.32) is set to

“OFF,” press VCR/TV on the remote to

be VCR mode.

Display will change as below.

Press

(CABLE)

125

(TV)

LINE2

LINE1

• “L1” or “L2” lights up on Multi Function Display

(about 4 seconds) when LINE1 or LINE2 is selected.

• Dubbing tapes protected with Copy

Guard will result in poor quality

Note

• LINE1: For rear audio/video connection.

recordings.

LINE2: For front audio/video connection.

Caution:• Unauthorized exchanging and/or copying of copyrighted recordings may be

• Please note that some tapes cannot be dubbed on DECK. Also, it is not

possible to dub DVD/ Video CD/ CD to VHS tapes using DECK.

Download from Www.Somanuals.com. All Manuals Search And Download.

Disc Operation

Subtitle Language (DVD only)

You can select a different subtitle language (if offered) than

the one set at the Settings for DVD Operation.

(See p. 47.)

Ready Checklist

Please read “Basic DVD Operation”

on p. 22.

[Subtitle language]

[Audio sound track language]

Press SUB TITLE*

in Play mode to display

the subtitle selection

on-screen.

• Display disappears after

5 seconds.

• When no subtitles are offered,

“-” will be displayed instead of

the language number.

ENG

FRA

DEU

ITA

English

French

German

Italian

ESP

NLD

SVE

NOR

DAN

POR

RUS

JPN

Spanish

Dutch

Press

Swedish

Norwegian

Danish

to select a language.

Press

to select “ON” or “OFF.”

Te amo

Portuguese

Russian

Japanese

Subtitle language being played back (see chart, right).

Notes

CHI

Chinese

Korean

Malay

• If after several presses of the button the language does not

change, language selection is not offered on the disc.

• When disc is removed, subtitles revert to initial setting

language. If the initial language is not recorded on the disc,

the disc’s priority language will appear.

KOR

MAL

VIE

Vietnamese

Thai

THA

Other

Audio Soundtrack Language (DVD only)

∗

You can change the audio soundtrack language, selected

at the Settings for DVD Operation, to a different language

if available. (See p. 47.)

• Change the No. by pressing

and press SET.

[Audio attribute 1 type, sampling

frequency, bit No. of the disc (see

p. 48.)]

(This operation works only with discs on which multiple

audio soundtrack languages are recorded.)

Press AUDIO

AUDIO: 1 ENG

Dolby Digital 3/2.1ch

16bit

in Play mode to display the

96 kHz

LPCM

20bit Linear PCM disc

24bit

Hello

audio selection on-screen.

48 kHz

• Display disappears after

Dolby Digital

DTS

1ch - 5.1ch

Dolby Digital disc

DTS disc

5 seconds.

SELECT

END

Audio attribute 1 type, sampling

frequency, bit No. of the disc or

number of speaker channel.

:AUDIO

Notes

• If, after several presses of the

AUDIO button the language does not

change, language selection is not

offered on the disc.

• When disc is removed, language

reverts to initial setting. If this

AUDIO: 3 ESP

Dolby Digital 3/2.1ch

Press

to select desired language.

Hola

SELECT

END

:AUDIO

language is not recorded on the disc,

the language recorded will be heard.

Audio soundtrack language being played back (see chart,

above right).

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

When

appears on the screen while

Multiple Angle Viewing (DVD only)

a button is being operated, it means

that the corresponding operation is

prohibited by DECK or the disc.

DVDs may contain scenes shot from multiple camera

angles allowing the same scene to be viewed at different

angles. You can view these angles, if available, using the

ANGLE button.

Press ANGLE

in Play mode to display the

angle selection on-screen.

• Display disappears after

5 seconds.

ANGLE Indicator

SELECT

Notes

Press

to select the desired

angle.

• The ANGLE Indicator lights up on

DECK when a scene recorded at

different angles is detected.

• The angle number can be set

beforehand so that the angle is

switched whenever the ANGLE

Indicator lights up.

SELECT

Number of angle being played back.

Vocal Selection for Karaoke Discs (DVD/Video CD)

Press AUDIO in Play mode

1 _{to display the audio screen.}

Press

(or

)

to select as shown below,

and

press (or ) to set.

(DVD only)

SELECT

SET

SELECT

END

:AUDIO

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF

• Video CD

ZOOM

SUB TITLE

Picture Zoom (DVD only)

You can enlarge specific portions of a picture and

select the zoom ratio using the ZOOM button during

DVD playback.

ANGLE

AUDIO

Press ZOOM repeatedly to change display

as follows.

Notes

• You can enlarge the center portion of the image

to one of 2 magnifications.

• The subtitle cannot be enlarged nor

can it’s position be changed.

• The picture zoom feature does not

work with a Video CD.

• During picture zoom, “ZOOM1” or

“ZOOM2” appears on-screen for 5

second.

• Zooming, on some discs, may result

in poor picture quality, or may not

operate at all.

I Use the

and

buttons to move the position

up, down, left and right.

Download from Www.Somanuals.com. All Manuals Search And Download.

Disc Operation (continued)

Title Menu (DVD only)

Some DVDs have more than one title, e.g. movies.

If the disc offers a title menu, you can select the desired

title number. (Operation may vary according to the disc.)

Press TITLE*

TITLE MENU

in Play mode

Dogs Castles

Birds

to display the title screen.

Lovers

Press

TITLE MENU

NUMBER keys

Dogs Castles

to select a title, and

press SET or PLAY

to start playing.

NUMBER

keys

CLEAR

Birds

Lovers

• “Pressing SET or PLAY” is

not necessary when using

NUMBER keys.

Birds

ACTION

SELECT

of the world

SET

PLAY

STOP

DVD Menu (DVD only)

TITLE

DVDs may offer a special menu. This menu may include

guides to unique contents, audio/subtitle languages, etc.

Although contents and operation may vary, the following

steps show basic steps for using the menu.

Press MENU

in Play mode to display

DVD MENU.

DVD MENU

1 . SUBTITLE

2 . AUDIO

3 . ANGLE

Press

DVD MENU

1 . SUBTITLE

2 . AUDIO

NUMBER keys

to select an item, and

press SET or PLAY

to perform.

3 . ANGLE

• “Pressing SET or PLAY” is

not necessary when using

NUMBER keys.

Repeat step 2 if there is

more than one menu.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Program Play (Video CD/CD only)

You can program specific tracks and order of play.

Press ACTION

Ready Checklist

DECK is in DVD mode, press DVD.

Video CD or CD is inserted.

Program Repeat Play

(Video CD/CD only)

to display DVD MAIN MENU.

DVD MAIN MENU

Press

DISC LANGUAGES

Do operation steps 1 through 5

to select

AUDIO OUTPUT

ST I LL MODE

TV MODE

P A R E N T A L L O C K

PLAY MODE

: AUTO

1 _{at left on this page.}

: 4 : 3 L e t t e r b o x

“PLAY MODE,” and

press SET

to display.

L E V E L

Press DISPLAY to display Disc

SELECT

SET

Information screen.

: SET

END

: ACTION

(Disc Information Screen)

TRACK

PBC

VIDEO CD

01 : 35 : 12

: OFF

PLAY MODE

Press

to select

PROGRAM PLAY

RANDOM PLAY

“PROGRAM PLAY,”

and

SELECT

SET

press SET to display.

SET

: SET

NEXT : DISPLAY

: SET

END

: ACTION

Press DISPLAY to display

DECK Information screen.

PROGRAM PLAY

Press

DISC

PROGRAM

11 16

12 17

13 18

14 19

to select a track

number (Track

numbers on disc are

displayed.), and

press SET.

Press SET to enter Select mode.

Cursor move to “OFF.”

10 15 20

CLEAR LAST

CLEAR ALL

SELECT

SET

END

(DECK Information Screen)

START

: SET

: ACTION

• Repeat step 4 to select another track.

• The selected track is added on the right side.

PROGRAM PLAY

Press

SET

: SET

END : DISPLAY

DISC

PROGRAM

11 16

to select “START,” and

press SET to start play

of programs in the

12 17

13 18

14 19

Press

to select “DISC.”

10 15 20

(DECK Information Screen)

CLEAR LAST

CLEAR ALL

START

SELECT

SET

sequence selected.

PLAY

REPEAT : DISC

PROGRAM PLAY

: SET

END

: ACTION

• To cancel, press STOP

during play, then press

CLEAR.

SELECT:

SET

: SET

END : DISPLAY

Notes

Press SET to set mode.

• Up to 15 tracks can be programmed.

• “ ” or “ ” (depending on disc) indicates additional

PROGRAM PLAY screen.

Cursor move to “REPEAT.”

To cancel, select “REPEAT :

OFF” in step 5, then press SET.

Press

• To clear the last program one by one

Press to move to “CLEAR LAST” and

for next or previous screen.

press SET. (Pressing CLEAR on remote control

also clears last program.)

• To clear all programs

Press

to move to “CLEAR ALL” and press

SET. (Programs are also cleared when the power

is turned off or the disc is removed.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Disc Operation (continued)

Random Play (Video CD/CD only)

Ready Checklist

DECK is in DVD mode, press DVD.

Tracks are played in a random order.

*Important:

Press ACTION*

If a remote control button does not

work when pressed, press the

DVD button on the remote and try

the button again.

to display DVD MAIN MENU.

DVD MAIN MENU

Press

DISC LANGUAGES

to select “PLAY MODE,”

AUDIO OUTPUT

ST I LL MODE

TV MODE

: AUTO

: 4 : 3 L e t t e r b o x

and

press SET

to display.

P A R E N T A L L O C K

PLAY MODE

L E V E L

SELECT

SET

: SET

END

: ACTION

CLEAR

PLAY MODE

Press

to select

ACTION

PROGRAM PLAY

RANDOM PLAY

“RANDOM PLAY,” and

press SET

SELECT

SET

SELECT

SET

END

to begin random play.

: SET

: ACTION

• To cancel, press STOP

during play, then press

CLEAR.

STOP

VOLUME

ADJUST

Setting the VOLUME ADJUST

Some DVD are recorded in lower average volume level.

For these DVD, this DECK can be set so that the

average volume is increased.

Press VOL.ADJ repeatedly to change “ON” ↔ “OFF.”

• “ON” or “OFF” lights up on Multi Function Display (about 3 seconds) when

press VOL.ADJ.

VOLUME ADJUST “OFF”

VOLUME ADJUST “ON”

Some DVD

[Volume level is low]

Volume level is increased

when played back.

Volume is the original level.

• “ON” is set ..... When a DVD is played back, the average volume is increased.

• “OFF” is set .... The volume level recorded on the disc is played back just as it is.

Notes

• When audio equipment is connected, setting the Sound Output level to “OFF” is recommended.

• If the sound becomes abnormal while playing a disc, set the Sound Output level to “OFF.”

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Operation using On-Screen Displays

When DISPLAY is pressed, On-Screen Displays show

Ready Checklist

DECK is in DVD mode, press DVD.

disc information (title/chapter/track number, elapsed

playing time) and DECK information (repeat play, play

mode).

Press DISPLAY in Play or Stop mode

to display “On-Screen Displays.”

• Each press of DISPLAY changes the on-screen

display as follows. (Refer to p. 42.)

NUMBER

keys

Selected disc information

➡

CLEAR

Selected DECK information

Normal Screen

SELECT

SET

Note

DISPLAY button does not function while DVD

TITLE MENU is displayed.

Press

to select an item, and

press SET.

(or

)

Press

or NUMBER keys

to select the setting, and

press SET.

DISPLAY

T I TLE

DVD

• When numbers are

displayed (e.g. title

number), NUMBER keys

are also available.

CHAPTER : 11

00 : 12 : 34

T I TLE

CHAPTER : 24

DVD

00 : 12 : 34

• If the number entered is

not on the disc, the entry

will have no effect.

Re-enter the correct

number.

SELECT:

SET

: SET

NEXT : DISPLAY

SELECT:

SET

: SET

NEXT : DISPLAY

• For more details, refer to

the disc operation

information.

TRACK : 12

PBC : OFF

VIDEO CD

00 : 12 : 34

TRACK : 17

PBC : OFF

VIDEO CD

00 : 12 : 34

To return to normal

screen,

press CLEAR or

DISPLAY repeatedly.

Notes

• When DISPLAY button is

pressed during playback of a

Video CD with Playback control,

NUMBER keys are not available

on the displayed screen. In this

case, press DISPLAY again to

remove the displayed screen.

SET

: SET

NEXT : DISPLAY

SET

: SET

NEXT : DISPLAY

• When

appears on the screen

while a button is being operated,

it means that the corresponding

operation is prohibited by DECK

or the disc.

Download from Www.Somanuals.com. All Manuals Search And Download.

DVDOperationusingOn-ScreenDisplays(continued)

Detailed Descriptions of each On-Screen Display

I Disc information screen (for DVD)

T I TLE

DVD

1. TITLE No.

CHAPTER : 12

01 : 12 : 55

• Select “TITLE”, and press SET*.

• Change the No. by pressing

2. CHAPTER No.

or NUMBER keys, and press SET.

• Select “CHAPTER”, and press SET.

SELECT:

SET

: SET

NEXT : DISPLAY

• Change the No. by pressing

or NUMBER keys, and press SET.

3. Disc currently being played

4. Elapsed playing time

T I TLE

DVD

01 : -- : --

CHAPTER : 12

The screen may be changed by selecting the elapsed time.

• Select the elapsed playing time (“xx:xx:xx”), and press SET.

• Change the elapsed time by pressing NUMBER keys.

Hours ➛ Minutes ➛ Seconds are entered in order.

If the time entered is not on the disc, the entry will have no effect.

Re-enter the correct time.

ENTER : 0

SET : SET

NEXT : DISPLAY

If SET is pressed while

making entries, unit

returns to the condition

before entries were made.

e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.

Hour Minutes Seconds

• This function does not work with some discs.

I Disc information screen (for Video CD/ CD)

A. TRACK No.

TRACK

PBC

VIDEO CD

01 : 35 : 12

: OFF

• Select “TRACK”, and press SET.

• Change the No. by pressing

B. Playback control ON/OFF

or NUMBER keys, and press SET.

[Video CD with playback control only]

ON Video CD menu play is displayed.

OFF Video CD menu play is not displayed.

C. Disc currently being played

Video CD CD

SET

: SET

NEXT : DISPLAY

D. Elapsed playing time

• Track No. and the elapsed playing time are not displayed during play started from menu of

Note

Video CDs with playback control.

• When

appears on the screen while a button is being operated, it means that the

corresponding operation is prohibited by DECK or the disc.

I DECK information screen (for DECK)

a. Repeat Play

PLAY

REPEAT : CHAPTER

• Select “REPEAT”, and press SET.

• Change the desired mode during play by pressing

, and press SET.

DVD

REPEAT CHAPTER REPEAT TITLE REPEAT OFF

REPEAT DISC REPEAT OFF

Video CD/CD REPEAT TRACK

b. Play mode [Video CD/ CD only] (See p. 39 or 40.)

PLAY

REPEAT : DISC

RANDOM PLAY

PROGRAM PLAY program play

RANDOM PLAY

----

random play

normal play

For your reference

•

CHAPTER/TITLE REPEAT PLAY (DVD)

•

TRACK/DISC REPEAT PLAY (Video CD/CD)

CURRENT PLAYBACK POSITION

TITLE

chapter

track

chapter chapter

TRACK REPEAT

DISC REPEAT

NORMAL PLAY

CHAPTER REPEAT

TITLE REPEAT

NORMAL PLAY

Note

• For repeat play in VCR mode, see p. 32.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

MP3/WMA/JPEG Playback Operation

This unit can play MP3/WMA/JPEG format CD-R or

MP3/WMA Playback

CD-RW recorded for personal use on a PC, etc.

Some discs may not play due to the condition of the

Do steps 1~3 on left.

recording.

Press

to select an MP3/WMA file ( / ).

Press POWER on the remote or DECK.

(During STOP mode)

Press OPEN/CLOSE,

then place an MP3/WMA/JPEG disc into

the disc tray.

Press OPEN/CLOSE to close.

• MP3/WMA/JPEG menu is displayed.

• Playback starts automatically

(except JPEG files).

Press SET or PLAY to start playback.

I Forward/Reverse Search

Press FF/SLOW+ or REW/SLOW- during play.

Press PLAY to release.

• Search speed, slow at first, increases with each

additional press of the button up to 5 levels.

I Forward/Reverse Track Skip

• CD directory is displayed.

Press SKIP

| or |

SKIP during play.

Function

Each press skips a track.

PLAY

Counter

Parent

folder

Status

• If pressed within first 3 seconds of playback,

skips to the previous track. If over 3 seconds,

ROOT

. .

END

DD CUB I C

CTURNE

_WALTZ

TECHNO

POPS

Folder area

(Current folder

appears green.)

returns to top of track. (|

SKIP only.)

AZZ

• Put DECK in Stop mode before performing

File area

(Selected file/

folder is

folder/file selection (see step 4.)

PLAY MODE : NORMAL

I Pause

highlighted.

Titles are

displayed

up to 11

characters.)

Press PAUSE during play.

PLAY MODE

:WMA file

Press PLAY to release.

:MP3 file

:Folder

Press STOP to stop play.

:Parent folder

Press OPEN/CLOSE to eject the disc.

The MP3/WMA/JPEG MENU is closed

automatically.

:JPEG file

(Diagram left shows CD directory

structure as displayed in example

OSD above.)

ROOT

• Copyright protected files and files

Note

containing errors cannot be played

back. The DECK skips to the next file.

END

DD_CUB I C

CTURNE

_WALTZ

Notes

I Select PLAY MODE [MP3/WMA Playback]

• Only File (not Folder) area

operation is possible.

• Files are displayed in the

following order:

(During STOP mode)

TECHNO

POPS

1) Press

to move cursor to

PLAY MODE.

2) Press

to select the desired PLAY

(!...0,1....9,A,B......Z).

AZZ

MODE (see below).

• Select file (During STOP mode)

1)Press to select an MP3/WMA file (

➡ MP3/WMA Playback (see right)

2)Press to select a JPEG file ( ).

➡ JPEG Playback (see p.44)

3)Press SKIP | (next) or |

(previous) to skip a file/folder page (7files)

in the File area.

• Select folder (During STOP mode)

[PLAY MODE]

NORMAL:

All MP3/WMA files are selected and

played back one time only.

SINGLE REPEAT:

The selected MP3/WMA file is played

back repeatedly.

FOLDER REPEAT:

The MP3/WMA files contained in the

selected folder are played back

repeatedly. However, folders below the

selected folder are not played back.

SKIP

1)Press

to select a folder ( ).

2)Press SET to display files/folders contained

in the folder.

• Select parent folder (During STOP mode)

DISC REPEAT:

All MP3/WMA files are played back

repeatedly.

1)Press

to select a folder ( ).

2)Press SET to make changes to the previous

directory display.

Important:

if a remote control button does not work

when pressed, press the DVD button on

Press ACTION to return the DVD MAIN

5 _{MENU. (➛ Press ACTION again to return}

the remote and try the button again.

Download from Www.Somanuals.com. All Manuals Search And Download.

the MP3/WMA/JPEG MENU.)

MP3/WMA/JPEGPlaybackOperation(continued)

I Select PLAY MODE [JPEG Slide-show]

JPEG Playback

(During STOP mode) (See p.43)

1) Press

to move cursor to

You can play back JPEG images.

PLAY MODE.

Displayable Image Size: 32x32~7680x7680 pixels

2) Press

MODE (see below).

to select the desired PLAY

• Some JPEG format may not be played

back.

Note

[PLAY MODE]

NORMAL:

Do steps 1~3 on page 43.

All JPEG files are selected and

played back one time only.

SINGLE REPEAT:

The selected JPEG file is played back

repeatedly.

FOLDER REPEAT:

The JPEG files contained in the

selected folder are played back

repeatedly. However, folders below the

selected folder are not played back.

Press

to select an JPEG file ( ).

Press SET or PLAY.

Selected JPEG file is displayed.

[JPEG Playback Screen]

DISC REPEAT:

All JPEG files are played back

repeatedly.

I Returned on the MP3/WMA/JPEG MENU

➡ Press STOP. (See p.43)

I Next/Previous Search

➡ Press SKIP

| or |

SKIP.

I Start Slide-show ➡ Press FF/SLOW+ or

REW/SLOW-. (below)

I Enlarging an image ➡ Press ZOOM. (P.45)

I Rotating an image ➡ Press ANGLE. (P.45)

Press STOP to return the MP3/WMA/

JPEG MENU.

JPEG Slide-show

(During JPEG Playback.)

Operation can be done when files are in

order, such as in the diagram below.

JPEG files are displayed automatically

(about every 3 seconds) as a slide-show.

Press FF/SLOW+ or REW/SLOW-.

ROOT

REW/SLOW-

01 PIC

FF/SLOW+

Image changes every 3 seconds.

AAA

DDD

TTT

UUU

VVV

WWW

I Cancel slide show

➡ Press STOP to return the MP3/WMA/

JPEG MENU. (See p.43)

I Still picture

➡ Press STILL (only SLIDE).

➡ Press PLAY to release.

REW/SLOW-

ZZZ

FF/SLOW+

I Forward/Reverse File Skip

➡ Press SKIP

| or |

SKIP.

Each press skips a file.

Press ACTION to return the DVD MAIN

MENU.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

JPEG Zoom

(During JPEG Playback.)

You can enlarge specific portions of a JPEG picture

and select the zoom ratio using the ZOOM button

on the remote during JPEG Playback screen.

Set Zoom size.

Press ZOOM repeatedly to change display as

follows.

➡ Press STOP to return the MP3/WMA/JPEG MENU.

• You can enlarge the center portion of the image to

one of 2 magnifications.

• Operation can be done during Rotation (below).

X 1.0 (ORIGINAL)

X 1.5 (ZOOM 1)

X 2.0 (ZOOM 2)

ACTION

STOP

1st press

2nd press

SELECT

SET

PLAY

SKIP

ZOOM

ANGLE

3rd press

REW/

SLOW-

I Use the

and

buttons to move the

position up, down, left and right.

(Position cannot be changed on X1.0

ORIGINAL images.)

FF/

SLOW+

STILL

JPEG Rotation

(During JPEG Playback.)

You can rotate a JPEG picture using the ANGLE

button on the remote during JPEG Playback

screen. (The JPEG picture will be rotated 90 °

clockwise.)

Setrotation.

Press ANGLE repeatedly to change display

as below.

➡ Press STOP to return the MP3/WMA/JPEG MENU.

• Operation can be done during Zoom (above).

• The vertical/horizontal ratio of rotated JPEG

images may vary when they are displayed.

1st press

2nd press

3rd press

4th press

MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and

Thomson multimedia.

Windows Media, and the Windows logo are trademarks, or registered

trademarks of Microsoft Corporation in the United States and/or other countries.

WMA is a compression format developed by Microsoft Corporation. It achieves

the same sound quality as MP3 with a file size that is smaller than that of MP3.

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD Lock Feature^{*Important: If a remote control button does not work when}

pressed, press the DVD button on the remote

and try the button again.

You can prevent playback of DVDs of a specific

Ready Checklist

DECK is in DVD mode, press DVD.

rating level which may be unsuitable for children.

• Some DVDs are encoded with a rating level. If the disc

rating is higher (stricter) than the one you preset,

playback will be prohibited.

DVD Lock (DVD only)

A 4-digit code must be entered to view a blocked

program or change rating settings.

Caution

Discs not encoded with rating

level will play even if the jacket

states it is for mature

audiences. For these discs, the

DVD Lock Ratings will not work.

Press ACTION*

to display DVD MAIN MENU.

DVD MAIN MENU

Press

DISC LANGUAGES

AUDIO OUTPUT

ST I LL MODE

TV MODE

to select “PARENTAL LOCK,”

: AUTO

: 4 : 3 L e t t e r b o x

and

PARENTAL LOCK : LEVEL 8

YOUR SELECTION EXCEEDS THE

PLAYER

RATING LIMIT.

DO YOU WANT TO CHANGE THE

LIMIT?

press SET to display.

SELECT

SET

: SET

: ACTION

YES

END

SELECT:

SET

: SET

END : DISPLAY

1) Press NUMBER keys

ENTER

CODE

After DVD Lock is set and a

blocked DVD is played, this

message will appear.

The message may differ

depending on the disc.

to enter your secret code.

----

2) Enter same secret code

again for confirmation.

3) Press SET to display.

ENTER

END

0-9

ACT

• Step 2) not necessary when

changing rating or secret

code.

• Take care that you are not

observed entering the

secret code.

To Make Corrections

Press repeatedly to

move the cursor.

Press NUMBER keys to

make the correction.

To continue viewing a blocked

program for now,

Press

to select “YES” and

SET. Then, enter your 4 digit

secret code (see step 3 left).

When “NO” is selected, blocked

programs cannot be viewed.

Press

to select rating level, and

press SET

to select “LOCKED” or

“UNLOCKED.”

PROGRAM RATING EXCEEDED

LEVEL 0 : LOCK ALL, Playback of all DVDs, CDs, Video

CDs, MP3, WMA and JPEG is prohibited.

(Use to prohibit play of mature theme DVDs not

encoded with rating level.)

LEVEL 1 : mature theme DVDs

LEVEL 2 : DVDs expressly for children can be played back.

LEVEL 3 to 7 : DVDs for general audiences/children can be

played back. (DVDs with mature content

are prohibited.)

LEVEL 8 : NO LIMIT: (Factory preset)

All DVDs can be played back.

Change your secret code

• You will need your current code.

Do step 1 ~ 2 left.

Enter current secret code.

Press CLEAR to clear the code.

Do step 4 to enter new code.

Note

• DO NOT forget your secret code.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings for DVD Operation

Once initial settings are done, they

Press ACTION

remain in memory (even after power off)

until changed. This means DECK will

operate under the same conditions

(especially DVDs) each time.

to display DVD MAIN MENU.

DVD MAIN MENU

Press

to select an item, and

press SET.

DISC LANGUAGES

AUDIO OUTPUT

ST I LL MODE

TV MODE

AUTO

: 4 : 3 L e t t e r b o x

L E V E L

Ready Checklist

P A R E N T A L L O C K

DECK is in DVD mode, press DVD.

SELECT

SET

END

: SET

: ACTION

DISC LANGUAGES (See below)

All languages offered on the disc can be set.

If the language not offered is set, the original disc

language will be selected.

NUMBER

keys

CLEAR

AUDIO OUTPUT (See p. 48.)

You can set the audio output that comes from the

digital audio output terminal.

ACTION

SELECT

STILL MODE (See p. 49.)

To select “FIELD” (Field still) or “FRAME” (Frame

still) to prevent jitter or make small text or fine

patterns clearly visible in a still picture. When

“AUTO” is set “FIELD” or “FRAME” is selected

automatically.

SET

TV MODE (See p. 49.)

To select whether the video material for a wide-

screen will be played back in the Pan & Scan style,

Letterbox style or 16 : 9 style.

“AUDIO” selections

(Factory preset: English)

To select the audio soundtrack language.

English/Spanish/French/Japanese

Original: Original disc language

OTHER ✱✱✱✱: Other language selection*¹

Disc Languages (DVD only)

“SUBTITLE” selections

(Factory preset: AUTO)

To select and set the language of the audio

soundtrack, subtitles, or title/DVD menus for all discs

to be played.

To select the subtitle language.

AUTO: Same language selected

for “AUDIO”

• If language set for “AUDIO” is used in

playback, subtitles will not appear.

• If another language is used during

playback, the subtitles will appear

in the language selected at “AUDIO”

setup.

DVD MAIN MENU

Press

DISC LANGUAGES

to select

AUDIO OUTPUT

ST I LL MODE

TV MODE

AUTO

: 4 : 3 L e t t e r b o x

L E V E L

“DISC LANGUAGES,”

and

press SET

to display screen.

P A R E N T A L L O C K

SELECT

SET

: SET

: ACTION

END

English/Spanish/French/Japanese

OTHER ✱✱✱✱: Other language selection*¹

“MENUS” selections

DISC LANGUAGES

: E n g l i s h

(factory preset: English)

Press

AUDIO

To select the language used in title

menus or DVD menus.

English/Spanish/French/Japanese

OTHER ✱✱✱✱: Other language selection*¹

SUBT I TLE : AUTO

to select an item, and

press SET repeatedly

for desired language.

(Please refer right.)

MENUS

: E n g l i s h

SELECT

SET

: SET

END

: ACTION

To enter OTHER ✱✱✱✱ code

number,

Press NUMBER keys (Please refer to

language codes on p. 50).

Press ACTION to redisplay DVD MAIN

MENU and go to step 2 to setup another

item.

To make corrections, press

repeatedly to delete language code

number, and correct.

Or, press ACTION twice to exit.

*¹If the selected language is not offered,

the original disc language is selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings for DVD Operation (continued)

Audio Output

Select the digital output to be output from the optical

digital audio output connector of DECK.

Ready Checklist

DECK is in DVD mode, press DVD.

Press ACTION*

Recommended setting

Type of amplifier

to be connected

to display DVD MAIN MENU.

Dolby

Digital

LPCM

(DVD)

DTS

DVD MAIN MENU

Press

to select

“AUDIO OUTPUT,”

and

press SET

to display screen.

No amplifier is connected

DISC LANGUAGES

AUDIO OUTPUT

AV amplifier (with digital

audio input connector)

withoutDolbyDigital/DTS

decoder

ST I LL MODE

TV MODE

: AUTO

: 4 : 3 L e t t e r b o x

PCM*¹

PCM

P A R E N T A L L O C K

L E V E L

PCM

SELECT

SET

END

: SET

: ACTION

AVamplifierincluding

Dolby Digital decoder

Bitstream

PCM

AV amplifier including

Dolby Digital/DTS decoder

AUDIO OUTPUT

Press

to select an item,

and

press SET

repeatedly for

output. (See below.)

Bitstream

LPCM(DVD)

: OFF

D o l b y D i g i t a l : B i t s t r e a m

d t s

DRC

: B i t s t r e a m

: OFF

• Make settings according to amplifier

connected to optical audio output as shown

in above table.

SELECT

SET

END

: SET

: ACTION

*1 When connecting an amplifier (with an

optical digital input connector) which does

not contain the Dolby Digital or DTS

decoder, be sure to select “PCM”.

If “Bitstream” is selected, starting DVD play

may cause such a high level of noise as to

be harmful to your ears and damage the

speakers.

I “LPCM (DVD)” selections

OFF: Linear PCM of less than 48 kHz/16 bit is

output. When playing DVDs recorded in linear

PCM of over 48 kHz/20 bit, no digital audio is

output. (Factory preset)

PCM: When playing DVDs recorded in linear PCM of

48 kHz/20 bit/24 bit or more, digital audio

converted to 44.1 kHz/16 bit or 48 kHz/16 bit is

output.

*2 When a DTS decoder is connected, please

select “Bitstream” in “dts”.

(Digital output of PCM audio is restricted to

48 kHz/16 bit or below for copyright protection.)

I “Dolby Digital”selections

Bitstream: Dolby Digital bitstream (1ch-5.1ch) is

output. (Factory preset)

PCM: When you have connected a amplifier that

doesn’t have a built-in Dolby Digital decoder.

I “dts” selections

Bitstream: DTS bitstream is output. (Factory preset)

PCM: When you have connected a amplifier that

doesn’t have a built-in DTS decoder.

“DRC (Dynamic Range Compression)”

selections

OFF: Normal audio range is selected. (Factory preset)

ON: For dynamic sound even at low volume, this

is useful for late-night listening. [Dolby Digital

DVDs only].

Press ACTION to redisplay DVD MAIN

MENU and go to step 2 to setup another

item.

Or, press ACTION twice to exit.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Still Mode

Set to reduce jitter in a displayed still picture or a motion

picture.

Press ACTION

to display DVD MAIN MENU.

DVD MAIN MENU

Press

to select “STILL MODE,”

and

press SET repeatedly

for mode. (See below.)

DISC LANGUAGES

AUDIO OUTPUT

ST I LL MODE

TV MODE

: AUTO

: 4 : 3 L e t t e r b o x

P A R E N T A L L O C K

L E V E L

ACTION

SELECT

SET

END

: SET

: ACTION

AUTO: “FIELD” (Field still) or “FRAME” (Frame still) is

automatically selected during the still mode.

(Factory preset)

SET

FIELD: “FIELD” (Field still) is always selected.

This setting will reduce jitter when compared

with “AUTO” on some discs.

FRAME:“FRAME” (Frame still) is always selected.

Some texts and fine patterns will be seen clearly

when compared with “AUTO” on some discs.

Press ACTION

3 _{to exit this mode.}

TV Mode

Set the screen display style for wide-screen video

material playback.

Press ACTION

to display DVD MAIN MENU.

DVD MAIN MENU

Press

Example

DISC LANGUAGES

to select “TV MODE,”

and press SET

repeatedly for mode.

(See below.)

AUDIO OUTPUT

ST I LL MODE

TV MODE

: AUTO

• Pan & Scan (Factory preset)

: 4 : 3 L e t t e r b o x

P A R E N T A L L O C K

L E V E L

SELECT

SET

END

: SET

: ACTION

4:3 Pan & Scan (Factory preset) :

Wide-screen video data is played in Pan & Scan

style (left and right of screen is trimmed.)

• Video data not formatted in Pan & Scan will play

in letterbox style.

4:3 Letterbox :

• Letterbox

Wide-screen video data is played in Letterbox

style (top and bottom of screen has black margin).

16:9 :

Set “16:9” when using Wide-screen TV.

Press ACTION

to exit this mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Language Code List

Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or

“MENUS” (see p. 47).

Code Language

6565 Afar

Code Language

7079 Faroese

7082 French

7089 Frisian

7165 Irish

Code Language

7678 Lingala

Code Language

8375 Slovak

6566 Abkhazian

6570 Afrikaans

6577 Ameharic

6582 Arabic

7679 Laothian

7684 Lithuanian

8376 Slovenian

8377 Samoan

7686 Latvian, Lettish 8378 Shona

7168 Scots Gaelic

7176 Galician

7178 Guarani

7185 Gujarati

7265 Hausa

7771 Malagasy

7773 Maori

8379 Somali

8381 Albanian

8382 Serbian

8385 Sundanese

8386 Swedish

8387 Swahili

8465 Tamil

6583 Assamese

6588 Aymara

6590 Azerbaijani

6665 Bashkir

6669 Byelorussian

6671 Bulgarian

6672 Bihari

7775 Macedonian

7776 Malayalam

7778 Mongolian

7779 Moldavian

7782 Marathi

7783 Malay

7273 Hindi

7282 Croatian

7285 Hungarian

8469 Telugu

8471 Tajik

6678 Bengali;Bangla 7289 Armenian

7784 Maltese

7789 Burmese

7865 Nauru

6679 Tibetan

6682 Breton

6765 Catalan

6779 Corsican

6783 Czech

6789 Welsh

6865 Danish

6869 German

6890 Bhutani

6976 Greek

7365 Interlingua

7378 Indonesian

7383 Icelandic

7384 Italian

8472 Thai

8473 Tigrinya

8475 Turkmen

8476 Tagalog

8479 Tonga

8482 Turkish

8484 Tatar

7869 Nepali

7876 Dutch

7387 Hebrew

7465 Japanese

7473 Yiddish

7487 Javanese

7565 Georgian

7575 Kazakh

7576 Greenlandic

7577 Cambodian

7578 Kannada

7579 Korean

7583 Kashmiri

7585 Kurdish

7589 Kirghiz

7879 Norwegian

7982 Oriya

8065 Panjabi

8076 Polish

8487 Twi

8083 Pashto, Pushto 8575 Ukrainian

8084 Portuguese

8582 Urdu

6978 English

6979 Esperanto

6983 Spanish

6984 Estonian

6985 Basque

7065 Persian

7073 Finnish

7074 Fiji

8185 Quechua

8590 Uzbek

8277 Rhaeto-Romance 8673 Vietnamese

8279 Romanian

8285 Russian

8365 Sanskrit

8368 Sindhi

8679 Volapük

8779 Wolof

8872 Xhosa

8979 Yoruba

8372 Serbo-Croatian 9072 Chinese

8373 Singhalese 9085 Zulu

7665 Latin

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Instruction Displays

These displays will alert you to a missed operation or provide further instructions.

Page

OSD

Caution

PLEASE SET CLOCK BY

PRESSING ACTION KEY

If you attempt to set or review a Timer

Recording and the Clock is not set...

If DECK is not in Stop mode or a cassette with

record tab is not inserted 2 minutes before a

Timer Recording is about to begin...

PLEASE PREPARE FOR TIMER

REC

If you press REC on the remote control or

DECK, and a cassette is inserted with no record

tab...

CHECK CASSETTE

RECORD TAB

If you press PLAY, FF, REW, or REC on the

remote control or DECK without a cassette

inserted...

NO CASSETTE

TO CANCEL TIMER REC

HOLD DOWN STOP KEY

FOR APPROX 3 SEC

If you press STOP or POWER

during a Timer Recording...

(visible in VCR mode only)

If head cleaning becomes necessary while

playing back a tape...

VIDEO HEADS MAY NEED

CLEANING PLEASE INSERT

HEAD CLEANING CASSETTE

OR REFER TO MANUAL

END

: PLAY

If you press a function button other than STOP/

EJECT or POWER while DECK is

in VCR Lock mode...

VCR LOCK ACTIVATED

REMOTE CONTROL IS SET

TO TV MODE

USE VCR : VCR KEY

USE DVD : DVD KEY

If you press an invalid key on the remote while

in TV mode...

PLEASE CHECK THE DISC,

AND FOR STAINS OR

SCRATCHES ON DISC

If you press PLAY, and DECK reads data from a

stained or scratched disc in DVD mode.

Playback of a disc with different region number was

attempted. Only discs marked region “1”, “ALL”, or

those that include “1” are playable on this DECK.

THIS DISC MAY NOT BE PLAYED

IN YOUR REGION

THIS TYPE OF DISC CANNOT BE

PLAYED. PLEASE INSERT A

DIFFERENT DISC

An unusable disc is inserted in the DECK.

This file format cannot be played.

CANNOT PLAY THIS FILE

THIS FILE IS PROTECTED

(Appears during MP3/WMA/JPEG file playback)

This file is copyright protected and cannot be

played back. (Playback is prohibited.)

IT IS PROHIBITED TO COPY

DVD/VIDEO CD/CD TO VHS

If you press REC in DVD mode...

Download from Www.Somanuals.com. All Manuals Search And Download.

Before Requesting Service

Check the following points if you are having trouble with your DECK.

Power

No power…

Correction

• Completely insert Power Plug into an AC outlet.

• Set POWER button to on.

• Make sure power source is active.

• Auto power-off (shutoff) occurs after about 5 min.

in DVD mode with no operation, or if there is no

broadcast signal in TV or Playback mode.

Turn the power back on. (pp. 23, 33)

Power turns itself off...

Correction

Recording & Playback

TV program cannot be recorded...

• Check connections between DECK, external

antenna, and TV.

• Check channel selections.

• Make sure your antenna system (CABLE or TV) is

correctly set. (Channels [p. 18])

• Make sure cassette record tab is intact. (p. 6)

• Confirm that clock is set to current time and date.

• Make sure Cable/DSS box (if used) is left on and

tuned to channel to be recorded.

Timer recording cannot be

performed…

• Set recording start/stop times correctly. (p. 24)

• Timer recording may not be performed or continued

if a power interruption occurs before or during a

Timer Recording, even after power is restored.

• Select channel 3 or 4 on TV to match VCR output

channel (3 or 4) (p. 16) or select LINE.

• Set VCR/TV selector to “VCR.”

There is no playback picture, or the

playback picture is noisy or contains

streaks...

• Adjust TRACKING control in either direction. (p. 6)

• Try Head Cleaning. (p. 6)

• Set TV’s Vertical Hold Control to MANUAL, then

adjust.

During special effects playback,

picture may contain some vertical

jitter when using a TV with an

Automatic Vertical Hold Control...

• Make sure DECK power is on.

• Check Remote batteries.

DECK cannot be controlled...

• Make sure VCR LOCK is set to off. (p. 33)

• Make sure Remote is in proper mode. (p. 28)

• Make sure Timer Recording is not in progress.

Remote Control

Correction

DECK cannot be remote controlled...

• Make sure DECK power is on.

• Make sure Remote is in VCR mode.

• Aim Remote Control directly at remote sensor on DECK. (p.9)

• Avoid any object blocking signal path.

• Check Remote batteries. (p. 4)

• Exposing DECK remote sensor to direct fluorescent

or outdoor light may cause signal interference.

• PROG functions are not available in COMPONENT

Video Output and S-VIDEO OUT. Set TV to either RF

IN or VIDEO IN. (p. 10)

PROG buttons do not respond...

• Check Remote batteries. (p. 4)

• Press VCR or DVD button for DVD/VCR mode. (p. 28)

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Check the following points if you are having trouble with your DECK.

DVD/ Video CD/ CD

Correction

Play fails to start even when PLAY is

pressed...

• This DECK cannot play discs other than DVDs,

Video CDs and CDs.

• The disc may be dirty and require cleaning.

Play starts but then stops immediately... • Be sure disc is installed with label side up.

Picture is distorted during rapid

advance or rapid reverse...

• The picture will be somewhat distorted at times:

this is normal.

No Forward/Reverse Scene Search

play...

• Some discs may have sections which prohibit

Forward/Reverse Scene Search. (p. 23)

Play does not start even when title is

selected...

• Confirm the “DVD LOCK” setting. (p. 46)

Audio soundtrack and/or subtitle

language is not the one selected at

the initial settings...

• If the audio soundtrack and/or subtitle language

selected at DVD initial settings does not exist

on the disc, it will not be accessible.

No subtitles...

• Subtitles appear only when available on disc.

• “OFF” is selected at the changing subtitle

language. Select “ON” at the “Subtitle Languages”

section (p. 36) to display the subtitles.

Alternative audio soundtrack

(or subtitle) language cannot be

selected...

• Alternative language cannot be selected with discs

which do not contain more than one language.

• For some discs, alternative language cannot be

selected with the AUDIO or SUB TITLE button.

Try selecting it from the DVD MAIN MENU if available.

Angle cannot be changed...

• This function is dependent on software availability.

Even if disc has multiple angles, they may be

recorded for specific scenes only (ANGLE

indicator on DECK lights up). (p. 37)

Correction

Miscellaneous

Programs cannot be viewed on TV...

• Make sure TV is set to output of DECK.

• Check connections between DECK,

external antenna, and TV.

• Set VCR/TV selector to “TV.” (p. 21)

• Make sure proper signal source is selected.

• Insert the cassette with window side up; record

tab facing you.

Video cassette cannot be inserted...

Video cassette ejects when

• Make sure cassette record tab is intact. (p. 6)

a recording is started or the power is

turned off for timer recording...

In Stop mode, the motor (CYLINDER)

continues to rotate...

• To enable Quick play mechanism, the cylinder will

rotate for about 3 minutes. This reduces response

time from Stop to Play mode.

The disc cannot be removed..

• First, unplug DECK. Then, prepare a rigid wire

(e.g. an extended paper clip) and, applying

moderate force, insert it straight into the hole at the

base of the tray. The tray will eject a little. Now, pull

the tray all the way out and remove the disc. (p. 9)

If you cannot resolve the problem, please call the Customer Call Center for product

assistance at 1-800-211-PANA (7262).

To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).

or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Limited Warranty

PANASONIC CONSUMER ELECTRONICS COMPANY,

DIVISION OF MATSUSHITA ELECTRIC

CORPORATION OF AMERICA

PANASONIC SALES COMPANY, DIVISION OF MATSUSHITA

ELECTRIC OF PUERTO RICO, INC.,

AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park,

Carolina, Puerto Rico 00985

One Panasonic Way Secaucus, New Jersey 07094

Panasonic/Quasar Video Products

Limited Warranty

Limited Warranty Coverage

If your product does not work properly because of a defect in materials or workmanship, Panasonic

Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)

will, for the length of the period indicated on the chart below, which starts with the date of original purchase

(“warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it

with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.

Product

Parts

Labor

Contact Number

Service

One (1) Year (except

CCD Image Sensor)

CCD Image Sensor - 6

(Six) Months

Ninety (90) Days

1-800-211-PANA(7262)

Carry-In or Mail-In

Camcorder

Ninety (90) Days

DVD/VCR Deck,

A/V Mixer

One (1) Year

Ninety (90) Days

1-800-211-PANA(7262)

Carry-In or Mail-In

One (1) Year (except

CRT)

CRT - Two (2) Years

Carry-In: 21” CRT

and Smaller

In-Home or Carry-In:

22” CRT and Larger

TV/VCR, TV/DVD,

TV/DVD/VCR

Combination

Ninety (90) Days

One (1) Year (except

CRT)

CRT - Two (2) Years

TV/HDR

Combination

1-888-843-9788

In-Home or Carry-In

Carry-In or Mail-In

Rechargeable

Batteries

(in exchange for

defective item)

Ten (10) Days

Not Applicable

1-800-211-PANA(7262)

Tape

(in exchange for

defective item)

Five (5) Days

Carry-In or Mail-In

Not Applicable

1-800-211-PANA(7262)

Memory Cards

(in exchange for

defective item)

Ninety (90) Days

During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period,

there will be no charge for parts. You must carry-in or mail-in your product or arrange for in-home service,

as applicable, during the warranty period.

If non-rechargeable batteries are included, they are not warranted. This warranty only applies to products

purchased and serviced in the United States or Puerto Rico. This warranty is extended only to the original

purchaser of a new product which was not sold “as is”. A purchase receipt or other proof of the original

purchase date is required for warranty service.

Carry-In, Mail-in or In-Home Service

For Carry-In, Mail-In or In-Home Service (as applicable) in the United States call toll free contact number

listed above or visit Panasonic Web Site: http://www.panasonic.com

For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.

In-Home service, if applicable, requires clear, complete and easy access to the product by the authorized

servicer and does not include removal or re-installation of an installed product. It is possible that certain

in-home repairs will not be completed in-home, but will require that the product, or parts of the product, be

removed for shop diagnosis and/or repair and then returned.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

Limited Warranty Limits And Exclusions

This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT

COVER normal wear and tear or cosmetic damage, nor does it cover markings or retained images on

the picture tube resulting from viewing fixed images (including, among other things, letterbox pictures

on standard 4:3 screen TV’s, or non-expanded standard 4:3 pictures on wide screen TV’s, or

onscreen data in a stationary and fixed location). The warranty ALSO DOES NOT COVER damages

which occurred in shipment, or failures which are caused by products not supplied by the warrantor,

or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication,

alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper

maintenance, power line surge, lightning damage, modification, or commercial use (such as in a hotel,

office, restaurant, or other business), rental use of the product, service by anyone other than a

Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY

COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY

BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having

someone remove or re-install an installed unit if applicable, or travel to and from the servicer, loss of

media or images, data or other memory or recorded content. The items listed are not exclusive, but

are for illustration only.)

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF

MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or

limitations on how long an implied warranty lasts, so the exclusions may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which vary from

state to state. If a problem with this product develops during or after the warranty period, you may

contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the

warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.

PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE

APPLICABLE) WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR

RESPONSIBILITY.

Customer Services Directory

For Product Information, Operating Assistance, Literature Request, Dealer Locations,

and all Customer Service inquiries please contact:

1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 9 am-7 pm, EST.

or send e-mail : [email protected]

For hearing or speech impaired TTY users, TTY : 1-877-833-8855

Web Site: http://www.panasonic.com

You can purchase parts, accessories or locate your

nearest servicenter by visiting our Web Site.

Accessory Purchases:

1-800-332-5368 (Customer Orders Only)

For hearing or speech impaired TTY users, TTY : 1-866-605-1277

Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032

(6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST)

(Visa, MasterCard, Discover Card, American Express, Check)

Service in Puerto Rico

Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Phone (787)750-4300 Fax (787)768-2910

As of August 2002

Download from Www.Somanuals.com. All Manuals Search And Download.

Spanish Quick Use Guide/ Guía para rápida consulta

CONEXIONES/CONFIGURACION INICIAL (READYTO PLAY)

Para ajustar el idioma, canal y

Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA.

El DVD/VCR iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA.

CONEXIONES

DVD/VCR

Terminal IN FROM ANT.

Televisor

Para Ant/Cable ➛ DVD/VCR ➛ TV

Entrada (IN) desde

ANT./CABLE

Conecte el cable de la antena al terminal IN

FROM ANT del DVD/VCR.

Conecte el terminal OUT TO TV del DVD/VCR

Terminal

OUT TO TV

a la entrada de la antena VHF/UHF del TV con

el cable RF incluido.

VHF/UHF

Para Sistema Digital de Satelite (DSS)/ Convertidor de cable ➛ DVD/VCR ➛ TV

Terminal

Conecte la salida de convertidor de cable

al terminal IN FROM ANT.

Televisor

IN FROM ANT. Estuche convertidor

de TV por cable

DVD/VCR

Conecte el terminal OUT TO TV del DVD/VCR

a la entrada de la antena VHF/UHF del TV con

el cable RF incluido.

Entrada (IN) desde

ANT./CABLE

Terminal

2 _{OUT TO TV}

CONFIGURACION INICIAL

VHF/UHF

Las fijaciones se realizan automáticamente.

Cuando termina las fijaciones, aparecerá la

siguiente pantalla.

Encienda el TV y cambie al canal 3.

Enchufe el cable de CA.

El DVD/VCR se encenderá e iniciará las

fijaciones de los canales y del reloj.

2003 SUN

20P

SETT

AUTO CLOCK SET

PLETED

CH 10

•

Si no aparece la pantalla de abajo, compruebe

la conexión del DVD/VCR-TV y si el canal del

TV está a 3, intennte cambiando al canal 4.

Para cambiar el canal de salida del DVD/VCR,

consulte las instrucciones de “Canal de salida

del VCR” (informaciones en inglés página 19).

COM

Si aparece en la pantalla “AUTO CLOCK SET IS

INCOMPLETE (FIJACION AUTOMATICA DEL

RELOJ ES INCOMPLETO)”, Ajuste el reloj

como se describe a continuación.

Enchufe el cable de CA.

AUTO CLOCK SET IS

NCOMPLETE

Al inicio, el idioma de la

CH AUTO SET PROCEEDING

pantalla está fijado a

CANCEL : STOP

PLEASE SET CLOCK BY

PRESSING ACT ON KEY

inglés.

Para cambiar el idioma,

AJUSTE MANUAL DEL RELOJ

Si la fijación ha sido incompleta.

AUTO CLOCK SET

seleccione la pantalla

PROCEEDING

MENU (informaciones en

Presione la tecla ACTION en el control remoto

para visualizar la pantalla del menú SET

inglés página 18).

CANCEL : STOP

CLOCK.

Si está usanndo un convertidor de TV por cable y

en su area hay un canal de Public Broadcast

Station (PBS), ajuste su convertidor al canal PBS

de su area. Si está usando un receptor DSS, este

debe estar apagado.

SET

CLOCK

----------------^D--^S-^T-^:O-^N--

SEL

ONTH

SELE

SET

EXIT

SET

ACT

Nota

Presione

para seleccionar el mes y SET

• Los botones de funciones no funcionan durante

la configuración inicial.

para ajustar. De la misma forma, seleccione y

ajuste la fecha, año, hora y DST (hora de

verano).

• Para retirar un cassette durante el ajuste

automático, presione EJECT en el control remoto

o STOP dos veces en el aparato. En este caso,

los ajustes de los canales y la hora se deben

hacer manualmente. Para los ajustes seleccione

la pantalla MENU (informaciones en inglés

página 18).

• Dependiendo de las condiciones, el ajuste

automático puede durar más de 30 minutos.

En ese caso, presione STOP para detener el

ajuste automático y realice los ajustes

manualmente en la pantalla MENU.

SET

CLOCK

2003 SUN

ST:

----------------^D----^O--^N-

SET CO

MPLETED

Presione dos veces la tecla ACTION para

poner el RELOJ en marcha y salir.

PRECAUCIÓN

Al usar cables coaxiales RF del tipo “tuerca”,

apriételos solamente con los dedos. Un apriete

excesivo puede dañar los terminales.

, p

se1-

l :-2

-8

-P(7

(

)

-m

l t

suemrperropdruodcutsc@tsp@apnaansaosnoinci.cc.ocomm

Download from Www.Somanuals.com. All Manuals Search And Download.

Operaciones básicas para la reproducción

Programación fácil para la

grabación con temporizador

Inserte un cassette,

• La alimentación del DECK se activa.

En la Pantalla de Visualización Multi

Función se ilumina “VCR”.

Presione PROG

para visualizar la pantalla de Programacion.

Presione PLAY para reproducir el cassette.

• Si el cassette no tiene la lengüeta de

prevención de grabación (página 6), se

inicia la reproducción automáticamente.

1) Para ajustar la FECHA de

INICIO PARADA

FECHA

SAB

--:-- --:-- --

grabación, presione

para seleccionar:

SLP

HOY

ELEGIR FECHA DE INICIO

1-31 = una vez, o

ELEGIR

FIJAR

DIARIO = a la misma hora

de lunes a viernes, o

SEMANA = a la misma

hora cada semana y

presione SET para ajustar.

SET

Detalles especiales durante la grabación

TERMINAR:PROG

Presione FF/SLOW+ o REW/SLOW- para

búsqueda de escenas hacia delante/ hacia

atrás. Presione PLAY para liberar. Durante

la búsqueda, cada vez que presione FF/

SLOW+ o REW/SLOW- se cambia la

velocidad como sigue:

Orden para elegir

Ejemplo

Fecha de hoy

Orden para elegir

DIARIO

[SLP] aprox. 21X ↔ aprox. 9X

SEMANAL

SAB

SEMANAL

LUN

SEMANAL

DOM

(

)

[LP]

[SP]

aprox. 9X ↔ aprox. 7X

aprox. 7X ↔ aprox. 3X

(

)

(

)

2) Para ajustar los ítems que quedan,

presione para seleccionar y presione

SET para ajustar los tiempos de INICIO/

PARADA, CANAL, o entrada de LINEA (pág.

35), y velocidad del cassette (SP, LP, SLP).

Presione PROG para finalizar PROGRAM.

Si la imágen se interrumpe con la velocidad de

21x, 9x o 7x, cambie la velocidad a 9x, 7x o 3x.

Presione PAUSE/STILL para imagen Fija

(Congelada).

Presione PLAY para liberar.

Presione PAUSE/STILL en el modo de

imagen fija para imágenes cuadro a cuadro.

Presione PLAY para liberar.

FE INIC

PARADA CA VEL

Presione

2 : 00

-- -- --

02 SLP

-- --

para seleccionar un número

que no está usando para

ingresar mas programas y

Presione FF/SLOW+ o REW/SLOW- en el

modo de imagen fija para cambiar la

velocidad de las imágenes a cámara lenta.

ELAR

DD/DLT

ELEGIR 1- 8

ENTRAR : SET

SALIR PROG

presione SET

para ajustar.

Presione STOP para detener el cassette.

Presione REW/SLOW- o FF/SLOW+ en el

modo de parada para rebobinado/avance

rápido del cassette.

Luego repita el paso 2.

Presione nuevamente

PROG para salir.

Presione EJECT en el control remoto,

o STOP/EJECT en el DECK para expulsar

el cassette.

Operaciones básicas para la grabación

Inserte el cassette con lengüeta de

protección de grabación (página 6).

Presione CH

, o las teclas de números

para seleccionar el canal.

Presione SPEED para seleccionar la

velocidad de grabación (página 6)

Grabación de un toque

Presione REC repetidamente para ajustar la

hora de grabación (30 min - 4 horas).

• SP = Reproducción estándar,

• LP = Larga duración,

• La videograbadora termina la grabación

a una hora programada.

• SLP = Superlarga duración.

4 ^{Presione REC para comenzar a grabar.}

• Para eliminar escenas indeseadas, presione

PAUSE/STILL para hacer una pausa, y al

presionar nuevamente continua la grabación.

• No podrá ver otro canal durante la

grabación.

Grabación normal

4:00 3:00

0:30

2:00

1:00

1:30

5 ^{Presione STOP para detener la grabación.}

Download from Www.Somanuals.com. All Manuals Search And Download.

Spanish Quick Use Guide/ Guía para rápida consulta

Operaciones básicas del DVD

Presione POWER en el control remoto o el

1 _aparato.

Presione DVD para seleccionar el modo DVD.

OPEN/

1) Presione OPEN/CLOSE.

3 _{2) Ponga un disco en la bandeja de disco.}

POWER

SELECT

• Sujete el disco sin tocar ninguna de sus

superficies, póngalo con el lado donde esté

impreso el título hacia arriba, alinéelo con las

guías y póngalo en su posición apropiada.

Disco de 3”(8 cm) / Disco de 5” (12 cm)

NUMBER

keys

Presione PLAY para iniciar la reproducción.

La bandeja del disco se cierra

automáticamente.

• Si está usando un DVD interactivo (Interactive

DVD) o un Vídeo CD con contol de

reproducción (playback control) y aparece un

menú de títulos (TITLE MENU) en la pantalla,

siga al paso 5.

DVD

SET

PLAY

SKIP

STOP

Presione

o las teclas numéricas para

seleccionar el artículo deseado.

REW/

SLOW-

SKIP

Presione SET o PLAY para la reproducción.

Si usa las teclas numéricas, la

reproducción comienza automáticamente.

FF/

SLOW+

Presione STOP para parar la reproducción.

PAUSE/

STILL

Presione OPEN/CLOSE para expulsar el disco.

IPara buscar una escena particular

Búsqueda hacia adelante

Presione FF/SLOW+ en el modo de reproducción.

Búsqueda hacia atrás

Presione REW/SLOW- en el modo de reproducción.

(Para liberar, presione PLAY)

IPara saltar un capítulo o una pista

Salto hacia adelante

Presione SKIP

l en el modo de reproducción.

Un capítulo (DVD) o una pista (Vídeo CD/CD)

se salta cada ves que se oprime la tecla.

Salto hacia atrás

Presione l

SKIP en el modo de reproducción.

IPara ver una imagen fija

Presione PAUSE/STILL durante la reproducción.

(Para liberar, presione PLAY)

IPara ver imágenes cuadro a cuadro

(DVD/Vídeo CD)

Presione PAUSE/STILL en el modo de imagen fija.

La imagen avanza un cuadro cada vez que

presiona la tecla. (Para volver a la

reproducción normal, presione PLAY.)

IPara ver en cámara lenta (DVD/Vídeo CD)

Presione FF/SLOW+ o REW/SLOW- en el modo

de imagen fija.

(Para liberar, presione PLAY)

, p

se1-

l :-2

-8

-P(7

(

)

-m

l t

suemrperropdruodcutsc@tsp@apnaansaosnoinci.cc.ocomm

Download from Www.Somanuals.com. All Manuals Search And Download.

Funcionnamiento del DVD utilizando

visualizaciones en pantalla

Cuando se presiona DISPLAY, la visualización en

pantalla muestra la información del disco (título / capítulo

/ número de lista, tiempo transcurrido de reproducción,

audio / idioma del subtítulo, y ángulo) e información

(repetir la reproducción, modo reproducción, Karaoke

vocal encendido / apagado, etc.).

Presione DISPLAY en el modo reproducción

1 _{o parada para visualizar las visualizaciones en}

pantalla.

• Cada vez que se presione DISPLAY, la

visualización en pantalla cambia como se

muestra a continuación.

Información seleccionada del disco

Información seleccionada del DECK

Pantalla normal

ADD/DLT

SELECT

SET

Presione

) para seleccionar el ítem

2 _deseado.

Presione SET para ajustar.

Presione

para seleccionar el ajuste

3 _deseado.

Presione SET para ajustar.

Para volver a la pantalla normal,

Presione repetidamente CLEAR o DISPLAY.

DISPLAY

T I TULO

DVD

00 : 12 : 34

T I TULO

DVD

00 : 12 : 34

CAPITULO: 11

CAPITULO: 24

ELEGIR :

FIJAR : SET SIGUIENTE: DISPLAY

PISTA

PBC

VIDEO CD

00 : 12 : 34

PISTA

PBC

VIDEO CD

00 : 12 : 34

INACTIVO

FIJAR : SET SIGUIENTE: DISPLAY

Download from Www.Somanuals.com. All Manuals Search And Download.

Spanish Quick Use Guide/ Guía para rápida consulta

Utilización de un menú de títulos

[DVD solamente]

Utilización de un menú de DVD

[DVD solamente]

Algunos discos con películas, vienen con dos o más

títulos. Por ejemplo, si el disco tiene un menú de

títulos grabados, el botón TITLE podrá utilizarse

para seleccionar el título de la película.

Algunos discos DVD ofrecen un menú especial.

Este menú incluye guías para contenidos únicos,

audio, subtitulos, idiomas, etc. Aunque los

contenidos y las operaciones se cambian, los

siguientes son unos pasos básicos para el uso del

menú.

Presione TITLE durante la reproducción.

Ahora se visualiza una lista de los títulos del

disco.

Presione MENU durante la reproducción.

El menú de DVD introducido en el disco se

visualiza ahora.

Presione

o las

TITLE MENU

teclas de números para

seleccionar el título

deseado.

Dogs Castles

Presione

o las

DVD MENU

Birds

^LoveD^rsogs

teclas de números para

seleccionar el ítem deseado.

Presione SET para elegir.

1 . SUBTITLE

2 . AUDIO

Presione SET para elegir.

of the world

3 . ANGLE

Ampliación de la imagen [DVD solamente]

Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar la

relación de zoom usando el botón ZOOM.

Presione ZOOM repetidamente para cambiar el

tamaño de la imagen como se indica a continuación:

2da

I Use los botones

para desplazar

la posición hacia arriba, hacia abajo, hacia la

izquierda o hacia la derecha.

3da

Funcionamiento de la ejecución de MP3/WMA/JPEG

I Ejecución MP3/WMA/JPEG (Durante el modo STOP)

Presione para seleccionar un archivo MP3/WMA

) o un archivo JPEG ( ), y presione SET o

Puede utilizar esta unidad para reproducir audio de

formato MP3/WMA/JPEG, grabado para uso personal

con una computadora, etc., en un CD-ROM o CD-RW.

La ejecución no podrá realizarse en algunos casos,

debido a las condiciones de la grabación.

(

PLAY.

• MP3/WMA

Búsqueda hacia adelante/hacia atrás

➡PresioneFF/SLOW+oREW/SLOW- durantelaejecución.

Salto de pista hacia adelante/hacia atrás

Presione POWER en el control remoto o DECK.

➡Presione SKIP

| o |

SKIP durante la ejecución.

Presione OPEN/CLOSE y a continuacion

2 _{coloque un disco MP3/WMA/JPEG en la bandeja}

• JPEG

Búsqueda siguiente/anterior

de discos.

➡Presione SKIP

| o |

SKIP.

Presione OPEN/CLOSE para cerrarla.

Inicie la muestra-diapositiva

➡Presione FF/SLOW+ o REW/SLOW-.

Ampliar una imagen ➡ Presione ZOOM.

Girar una imagen ➡ Presione ANGLE.

Presione STOP para detener la operacion descrita arriba.

I Seleccione MODO DE REPRODUCCION

(Durante el modo STOP)

Se visualizará el MENU MP3/WMA/JPEG y la

ejecución se iniciará automáticamente. (Se

visualizará el directorio del CD.)

Estado de la

REPROD

Contador

Presione

para mover el cursor a MODO DE

para seleccionar el

función

Carpeta

ROOT

. .

REPRODUCCION, y Presione

MODO DE REPRODUCCIÓN deseado.

[MODO DE REPRODUCCIÓN]

NORMAL: Todos los archivos se reproducen sólo una vez

REPETICION DE UNA MUSIC:

El archivo seleccionado se reproduce repetidamente.

REPETICION DE UN ARCHIVO:

END

DD CUB I C

CTURNE

_WALTZ

principal

TECHNO

POPS

AZZ

Area de las

carpetas

(La carpeta

visualizada

actualmente se

volverá verde)

Area de

archivos

(El archivo/ la

carpeta se

visualiza con

un cursor.)

MODE DE REPRODUCCION:

NORMAL

Los archivos que se encuentran en la carpeta

seleccionada se reproducen repetidamente.

REPETICION DEL DISCO:

MODO DE REPRODUCCIÓN

:Archivo MP3

:Carpeta

:Archivo WMA

:Archivo JPEG

Todos los archivos se reproducen repetidamente.

Presione ACTION para regresar al DVD MENU

:Carpeta principal

5 _PRINCIPAL.

, p

se1-

l :-2

-8

-P(7

(

)

-m

l t

suemrperropdruodcutsc@tsp@apnaansaosnoinci.cc.ocomm

Download from Www.Somanuals.com. All Manuals Search And Download.

Fijaciones iniciales

Selección de IDIOMAS DEL

DISCO [DVD solamente]

Presione DVD para seleccionar el modo DVD.

Seleccione “AUDIO”

Presione ACTION en el modo de parada para

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonesa :

Original : Se seleccionará el idioma

original de cada disco.

visualizar MENU.

Presione

para seleccionar el artículo deseado.

Presione SET.

IDIOMAS DEL DISCO

OTRO ✱✱✱✱ : Se puede seleccionar el otro

Todos los idiomas ofrecidos en el disco pueden ser

ajustados. Si el idioma ajustado no es ofrecido en el

disco, se seleccionará el idioma original del disco.

SALIDA DE AUDIO

idioma.

Seleccione“SUBTITULO”

AUTO : Se seleccionará el mismo que fue

seleccionado en la preparación de

“AUDIO”. (Fijación de fábrica)

Puede usted ajustar la salida audio procedente del

terminal de salida audio digital.

DETENER RASTREO

• Si el idioma seleccionado en la preparación

de “AUDIO” se utiliza durante la

Para seleccionar “CAMPO” o “CUADRO fijo” para

prevenir inestabilidad o para permitir ver textos

pequeños o patrones finos claramente en el modo de

imagen fija.

reproducción, los subtítulos no aparecerán.

• Si se utiliza otro idioma durante la

reproducción, los subtítulos aparecerán en el

idioma seleccionado en la preparación de

“AUDIO”

Inglés / Español / Francés / Japonesa :

OTRO ✱✱✱✱ : Se puede seleccionar el otro

idioma.

Seleccione “MENU”

(Fijación de fábrica : inglés)

TV PREFERENCIA

Para seleccionar cuando el material del vídeo es para

pantalla ancha y se quiere reproducir en el estilo Pan&Scan,

en el estilo Letterbox o en el estilo 16 : 9 en la pantalla.

Presione

para seleccionar el artículo deseado.

4 _{Presione SET.}

5 _{continuar el ajuste.}

Volver a visualizar el menú de DVD para

Inglés / Español / Francés / Japonesa :

OTRO ✱✱✱✱ : Se puede seleccionar el otro

idioma.

Presione ACTION y pase al paso 3 para ajustar otro

ajuste o, para salir, presione ACTION tres veces.

Cambio del idioma de subtítulos

[DVD solamente]

Visión desde otro ángulo

[DVD solamente]

EI idioma de los subtítulos seleccionado al hacer las

fijaciones iniciales se puede cambiar por otro idioma

diferente, si éste se encuentra disponible.

Algunos discos DVD tienen escenas que han sido

filmadas simultáneamente desde un número de ángulos

diferentes. Con estos discos, la misma escena podrá

verse desde cada uno de estos ángulos diferentes

utilizando el botón ANGLE.

Presione SUBTITLE durante

la reproducción.

ANGULO: 1

Presione ANGLE durante la

Cuando no haya subtítulos

reproducción para visualizar

grabados, se visualizará “-” en

ELEGIR

ACTIVO / INACTIVO

TERMINAR

la selección del ángulo.

lugar del número de idioma.

: SUB TITLE

Presione

para

ELEGIR

^{seleccionar el idioma deseado.}2

ANGULO: 2

Presione

para

Presione

para

seleccionar el ángulo

seleccionar “ACTIVO” o

ELEGIR

ACTIVO / INACTIVO

TERMINAR

deseado.

: SUB TITLE

“INACTIVO.”

ELEGIR

Selección de vocal para los

discos de Karaoke [DVD/Vídeo CD]

Cambio del idioma de la pista

de sonido [DVD solamente]

EI idioma de la pista de sonido seleccionado al hacer

las fijaciones iniciales se puede cambiar por otro

idioma diferente, si éste se encuentra disponible.

Presione AUDIO

Presione AUDIO durante la reproducción

1 _{para visualizar la pantalla AUDIO.}

Presione

para seleccionar el ajuste

deseado.

)

durante la reproducción

para visualizar

SONIDO en la pantalla.

Presione

ajustar. (DVD solamente)

(o ) para

ELEGIR

TERMINAR : AUDIO

ELEGIR

TERMINAR : AUDIO

Presione

para

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF

seleccionar idioma.

• Video CD

ELEGIR

Download from Www.Somanuals.com. All _TM_ERMa_INn_ARuals Search And Download.

: AUDIO

Index

DECK & VCR

A ACTION button ................................. 8, 18

Accessories ............................................ 4

ADD/DELETE button

(Add or Delete a Channel) .................. 8, 19

Audio Broadcast types

(Stereo/SAP/Mono) ............................ 26

Audio Mode (Playback, Recording) .... 27

Auto Operation Functions .................... 31

Auto Shut-Off ........................................ 33

R REC button (Record on a Tape) ..... 8, 21

Record Tab ............................................ 6

Remote Sensor ...................................... 9

Remote Warning .................................. 34

Repeat Play ......................................... 32

Reset All Memory Functions ................. 9

REWIND/SEARCH button ............... 8, 20

S SAP/Hi-Fi ............................................. 27

B Batteries ................................................. 4

(Index and Program End Search) ..... 30

SLOW+/SLOW button

C Channel (“SET UP CHANNEL”) .......... 18

Channel Up/Down,

(Slow Motion Picture) ........................ 8, 20

Spanish Quick Use Guide ........... 56 ~ 61

Specifications......................................... 7

SPEED button .................................. 8, 21

Still (Freeze) Picture ............................ 20

STOP button..................................... 8, 20

Tracking/V-Lock Button ......................6, 8

Clock (“SET CLOCK”).......................... 18

Commercial Skip ................................. 31

Connections................................. 12 ~ 15

Copy Your Tapes (Dubbing) ............... 35

COUNTER RESET button ............... 8, 32

Customer Services Directory............... 55

T Tape Position, Tape Status ................. 34

Timer Recording .................................. 24

Trouble Shooting ........................... 52, 53

TV mode button................................ 8, 28

D DISPLAY button ............................... 8, 11

DST (Daylight Saving Time) ................ 19

V VCR Lock ............................................. 33

VCR mode button ............................ 8, 28

VCR/TV button ................................. 8, 21

VCR/TV Selector Function .................. 32

E EJECT button ................................... 8, 20

ENTER button

(For tuning TV Channel) ................ 8, 28

F FAST FORWARD/SEARCH button .. 8, 20

H Head Cleaning ...................................... 6

VOLUME +/ button (TV Volume) ... 8, 28

WWarning and Instruction Displays ....... 51

Weak Signal Display ........................... 33

I Index Search ........................................ 30

Indicator (Multi Function Display) ....... 11

Initial Setup (Ready to Play) ......... 16, 17

INPUT button ................................... 8, 35

Z ZERO SEARCH button .................... 8, 32

L Limited Warranty ........................... 54, 55

Location of Controls

(Remote, DECK) .......................... 8 ~ 10

MMulti-Brand Control ....................... 28, 29

OOn-Screen Displays (VCR) .................. 11

One Touch Recording ......................... 21

P PAUSE/STILL button (Still Picture) .. 8, 20

PLAY button (Playback a Tape) ...... 8, 20

POWER button ....................................... 8

PROG button (PROGRAM).............. 8, 24

Program Clear, Review, Replace ....... 25

Program End Search ........................... 30

Q Quality Picture ........................................ 6

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

DVD

A ACTION button ................................. 8, 47 S SEARCH button

ANGLE button

(Multiple Angle Viewing) ......... 8, 37, 45

AUDIO button

(Forward/Reverse Scene Search) .. 8, 23

SKIP l or l button

(Forward/Reverse Chapter/Track) .. 8, 23

(Audio Soundtrack Language) ....... 8, 36

Audio Output

(For Selecting Audio Output) ............. 48

Auto Power Off Function ...................... 23

Slide-show ........................................... 44

SLOW+/SLOW button

(Slow Motion Picture)....................... 8, 23

STILL button

(Still Picture or Pause) ................... 8, 23

Still Mode

C CLEAR button ............................ 8, 39, 46

Component Video Output .............. 10, 13

(For selecting “FIELD” or “FRAME”)...... 49

STOP button..................................... 8, 22

SUB TITLE button

(For selecting Subtitle Language) .. 8, 36

S-Video Out.................................... 10, 13

D Disc Languages ................................... 47

DISPLAY button

(“On-Screen Display”).................... 8, 41

DTS ...................................................... 14

DVD Menu ........................................... 38

DVD mode button ............................ 8, 28 T TITLE button (Title Menu) ................ 8, 38

DVD Lock Ratings ............................... 46

TV Mode

(For selecting the screen display style) ...... 49

F Frame by Frame Picture ...................... 23

Forwards/Reverse Chapter/Track ....... 23 V Video CD ............................................. 23

Forwards/Reverse Scene Search ....... 23

J JPEG ............................................ 43 ~ 45

K Karaoke

VOLUME ADJUST ........................... 8, 40

V.S.S. (Virtual Surround Sound) ..... 8, 23

WWMA ..................................................... 43

(Vocal Selection for Karaoke Discs) .... 37 Z ZOOM button (Picture Zoom)..... 8, 37, 45

L Language Code List ............................ 50

MMENU button

(To display DVD Menu) ................. 8, 38

MP3 ...................................................... 43

Multiple Angle Viewing........................ 37

OOPEN/CLOSE button....................... 8, 22

Optical Digital Audio Output .......... 10, 15

P PLAY button (Play a Disc) ............... 8, 22

Program Play (For Video CD/ CD) ...... 39

PROGRESSIVE button .......................... 9

Progressive Scan................................. 10

R Random Play (For Video CD/ CD) ...... 40

Repeat Play ......................................... 42

Resume Function................................. 23

RETURN button ............................... 8, 22

Rotation................................................ 45

Download from Www.Somanuals.com. All Manuals Search And Download.

Panasonic Consumer Electronics Company,

Division of Matsushita Electric Corporation of America

One Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company (“PSC”),

Division of Matsushita Electric of Puerto Rico, Inc.

Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina,

Printed in Indonesia

LSQT0674B

Puerto Rico 00985

S0103-1033

Download from Www.Somanuals.com. All Manuals Search And Download.

Miele Microwave Oven DA249 4 Alu User Manual
Nextar Digital Photo Frame N3 506 User Manual
Nilfisk ALTO Vacuum Cleaner CR 1500 Diesel User Manual
Norcold Refrigerator N61X User Manual
One for All Universal Remote URC 7562 User Manual
Oregon Scientific Watch RA126 User Manual
Oster Blender 14 CUP FOOD PROCESSOR WITH 5 CUP WORK BOWL User Manual
Oster Blender 109478 User Manual
Panasonic Conference Phone KX TS401W User Manual
Pass Labs Speaker SR 1 User Manual