Panasonic Smoke Alarm 1828 User Manual

Fire alarm systems  
External Fire Brigade  
Panel 1828  
Control (key required) and indicating panel for the fire brigade personnel, etc.  
Compact size  
The unit has the following push buttons:  
Ext. Fire Brigade Panel  
Alarms queued, used to scroll amongst  
the alarms.  
This unit (S/W V1.2) is primarily intended  
to be used by the fire brigade personnel, i.e.  
for pre-warning, co-incidence, fire and  
heavy smoke / heat alarm presentation.  
Point or zone alarm presentation and fire  
alarm reset are as in the c.i.e. it is connected  
to. You can scroll amongst two or more  
alarms in the system. All or selected alarms  
will be presented in a display (LCD, 2x40  
characters with back-light). An alarm text  
will be presented together with each alarm,  
if programmed in the c.i.e. Furthermore,  
>617 texts for selected alarms can be stored  
in the unit and will in such a case be shown,  
instead of the texts sent from the c.i.e. for  
these alarms. A built-in buzzer will sound  
like in the c.i.e. Any fault in the system will  
be presented as "General fault in system"  
and the buzzer will sound. The unit is  
power supplied via the c.i.e. or ext. power  
supply.  
Silence buzzer, used to silence the  
buzzer (it will re-sound for a new  
alarm.  
Silence alarm devices, used to silence  
the alarm devices (they will re-sound  
for a new alarm.  
Reset, used to reset the fire alarms.  
The designation texts on the front are in  
1828SE in Swedish but a neutral front for  
other languages is available (1828CC).  
Compact size  
The compact size enclosure is made of grey  
high impact ABS. Fitted with a supple-  
mentary "O" ring gasket, it will comply with  
IP61, in respect of dust and moisture. A key  
is required to get access to the push buttons  
and they are disabled until they are supposed  
to be used. A key is not required for the  
alarm presentation and to silence the buzzer.  
Two compression glands are attached. The  
unit shall be wall mounted.  
LEDs, push buttons etc.  
The unit has the following LEDs:  
Fire and Alarms queued, indicating  
pre-warning, co-incidence, fire and  
heavy smoke / heat alarm  
SW mode and address setting  
The display and the push buttons are used to  
set the SW mode and address, see the  
opposite side of this page.  
Operation, indicating that the unit is  
connected to  
a
c.i.e. and power  
supplied, i.e. it is in operation.  
Extinguishing, indicating activated  
output for Extinguishing equipment.  
Ventilation, indicating activated output  
for Ventilation equipment.  
Fire brigade tx, indicating activated  
output for Fire brigade tx (routing  
equipm.).  
Product application  
The 1828 unit is intended for indoor use and  
in dry premises. SW mode 1826/28 - 1587  
is intended to be used in the systems  
EBL512 and EBL128 SW mode 1826/28 –  
1582 in the systems EBL500 / 512 / 1000 /  
2000.  
Panasonic Electric Works Fire & Security Technology Europe AB  
Citadellsvägen 23, SE-211 18 Malmö, Sweden  
Tel: +46 (0)40 697 70 00 • Fax: +46 (0)40 697 70 99  
Download from Www.Somanuals.com. All Manuals Search And Download.  

MTX Audio Speaker 600WM User Manual
Napoleon Grills Gas Grill Gourmet Gas Grill User Manual
National Instruments Switch SCXI 1190 1191 User Manual
Navman GPS Receiver N60i User Manual
NETGEAR Modem GS116 User Manual
Niles Audio Home Theater System PRO15SW User Manual
Numark Industries Musical Instrument CD MIX 1 User Manual
Omega Vehicle Security Thermometer HH507 User Manual
Panasonic Blood Pressure Monitor EW3006 User Manual
Panasonic Electric Shaver ESLA93 User Manual