Panasonic Smoke Alarm 1826 User Manual

Fire alarm systems  
External Fire Brigade  
Panel 1826  
Control and indicating panel for the fire brigade personnel  
Built-in printer (option)  
The unit has the following push buttons:  
Ext. Fire Brigade Panel  
This unit is intended to be used by the fire  
brigade personnel, i.e. for pre-warning, co-  
incidence, fire and heavy smoke / heat alarm  
Alarms queued, used to scroll amongst  
the alarms.  
Silence buzzer, used to silence the  
buzzer (it will re-sound for a new  
alarm.  
presentation.  
Point or zone alarm  
presentation and fire alarm reset are as in the  
c.i.e. it is connected to. You can scroll  
amongst two or more alarms in the system.  
All or selected alarms will be presented in  
the unit's display (LCD, 2x40 characters  
with back-light). An alarm text will be  
presented together with each alarm, if  
programmed in the c.i.e. Furthermore, >  
617 texts for selected alarms can be stored in  
the unit and will in such a case be shown,  
instead of the texts sent from the c.i.e. for  
these alarms. A built-in buzzer will sound  
like in the c.i.e. Any fault in the system will  
be presented as "General fault in system"  
and the buzzer will sound. The unit is  
power supplied via the c.i.e. or ext. power  
supply.  
Silence alarm devices, used to silence  
the alarm devices (they will re-sound  
for a new alarm.  
Reset, used to reset the fire alarms.  
, used for paper feed, when the unit is  
provided with a printer 1835 (option).  
The designation texts on the front are in  
1826SE in Swedish but a neutral front for  
other languages is available (1826CC).  
Ext. FBP 1826 & Printer 1835  
The ext. FBP 1826 consists of a grey metal  
cabinet with a door. A key is required to  
open the door, which has a Plexiglas in front  
of the FBP front, see photo. It has cable  
inlets on the top, bottom and back sides and  
is intended to be wall mounted. Two  
compression glands are attached.  
LEDs, push buttons etc.  
The unit has the following LEDs:  
A Printer 1835 can be mounted in the ext.  
FBP 1826. It will print all the alarms,  
including the alarm texts.  
Fire and Alarms queued, indicating  
pre-warning, co-incidence, fire and  
heavy smoke / heat alarm.  
SW mode and address setting  
The display and the push buttons are used to  
set the SW mode and address, see the  
opposite side of this page.  
Operation, indicating that the unit is  
connected to  
a
c.i.e. and power  
supplied, i.e. it is in operation.  
Extinguishing, indicating activated  
output for Extinguishing equipment.  
Ventilation, indicating activated output  
for Ventilation equipment.  
Fire brigade tx, indicating activated  
output for Fire brigade tx (routing  
equipment).  
Product application  
The 1826 unit is intended for indoor use and  
in dry premises. SW mode 1826/28 – 1587  
2nd Cab is intended to be used in the  
systems EBL512 and EBL128 and SW  
mode 1826/28 – 1582 2nd Cab in the  
systems EBL500 / 512 / 1000 / 2000.  
Panasonic Electric Works Fire & Security Technology Europe AB  
Citadellsvägen 23, SE-211 18 Malmö, Sweden  
Tel: +46 (0)40 697 70 00 • Fax: +46 (0)40 697 70 99  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Cooktop CS1012 User Manual
Mr Heater Gas Heater MH125KTR User Manual
MTD Lawn Mower 950 959 Series 960 969 Series E960 E969 Series User Manual
MTD Lawn Mower ZT 42 User Manual
Multiquip Lawn Mower J36S60 User Manual
Multiquip Welding System BLW 400SSW User Manual
Muratec All in One Printer F 525 User Manual
Oki Printer 62411601 User Manual
Oregon Scientific Weather Radio RAA501H User Manual
Parasound Stereo Amplifier 5250 V2 User Manual