Operating Manual
Document Scanner
Model No.
KV-S1057C
KV-S1027C
KV-SL1066
KV-SL1056
KV-SL1055
KV-SL1036
KV-SL1035
These instructions contain information on operating the scanner. Before reading these instructions, please read
the Quick Installation Guide enclosed with this unit.
Keep all documentation in a safe place for future reference.
Current model availability depends on your country/area. Please contact your dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
High-speed Double Sided Scanning
•
This scanner can scan documents at high speed, regardless of the image type (monochrome / color).
Background Color Switch Function
•
Using the software, you can switch the background color of scanned images between white and black.
Double Feed Detection Function
•
This scanner contains an ultrasonic sensor for the detection of double feeding. Double feeding can be
detected even if you scan documents that contain paper of various thicknesses.
Double Feed Skip (DFS) Function
•
If scanning has been stopped because a double feed was detected, you can easily resume scanning by
pressing the Skip button. When you scan documents that include items that you do not want to be detected
as double feeding (for example, documents that have receipts attached, envelopes, etc.), the double feed
detection function can be enabled and still scan these documents.
Push Scan
•
This scanner has a push scan function for starting scanning without operation through a computer.
Scanning is started by selecting from settings that have been registered in advance with the cursor button,
and then pressing the scanner’s OK button*1 or Start/Stop button*2. This scanner also has a function that
starts scanning when you place documents on the feed tray (Touch Free Scanning).
*1
KV-S1057C and KV-S1027C
KV-SL1066, KV-SL1056, KV-SL1055, KV-SL1036 and KV-SL1035
*2
Card Scanning
•
A maximum of 3 cards can be loaded on the feed tray.
Mixed Batch Card Guide
•
A mixed batch card guide is available for scanning mixed media (cards and papers) at the same time.
Manual Feed Selector
•
Bound documents can be scanned by setting the manual feed selector to manual scanning (Manual).
Other Features
•
•
The paper feed path can be opened widely to easily remove jammed paper and perform maintenance.
This scanner has a counter function which indicates the approximate time for cleaning and replacement
of the rollers. The counters can be configured and checked in User Utility.
Operating Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Abbreviations
•
•
•
•
•
•
Windows® refers to the Microsoft® Windows® operating system (hereafter Windows).
Windows® XP refers to the Microsoft® Windows® XP operating system (hereafter Windows XP).
Windows Vista® refers to the Microsoft® Windows Vista® operating system (hereafter Windows Vista).
The explanations and screen shots in this manual are based on the Windows 7 operating system.
The screen shots used in this manual may differ from the screens displayed on your computer.
The illustrations in this manual are based on the KV-S1057C.
Trademarks
•
Microsoft, Windows, Windows Vista, and Internet Explorer are either registered trademarks or trademarks
of Microsoft Corporation in the United States and/or other countries.
•
•
ISIS is a registered trademark or trademark of EMC Corporation in the United States and/or other countries.
IBM is a trademark of International Business Machines Corporation, registered in many jurisdictions
worldwide.
•
•
Intel and Intel Core are trademarks of Intel Corporation in the U.S. and/or other countries.
Adobe and Adobe Reader are either registered trademarks or trademarks of Adobe Systems Incorporated
in the United States and/or other countries.
•
All other trademarks identified herein are the property of their respective owners.
4
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About the Documentation
The scanner documentation consists of 2 manuals: the Operating Manual (this manual), and the Quick
Installation Guide.
Operating Manual
This manual provides information about the operation of the unit.
(this manual)
The Quick Installation Guide explains about safety precautions and other
Quick Installation Guide important information, and outlines brief installation procedures of the unit and
software.
About the Software Help
Each software contains help files.
Software / Manual CD-ROM Contents
—
—
—
Device Driver
TWAIN
Drivers
ISIS
Panasonic proprietary application
for configuring advanced
scanning settings
Applications
Utilities
Image Capture Plus
—
—
User Utility
Scan Button Setting Tool
Operating Manual
This manual
Documents
Control sheet
Operating Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
System Requirements
®
Computer
CPU
IBM PC/AT or compatible machine with a CD-ROM drive
®
Intel Core™ i5 2.5 GHz or higher
Memory
Interface
4 GB or higher
USB 2.0 / USB 3.0
Note
•
•
For details about the system requirements, refer to [Read me first] in the Software / Manual CD-ROM.
The scanning speed differs depending on the host computer’s operating environment or the application
used.
•
•
Due to the slower speed of USB 1.1, it is recommended to use a USB 2.0 / USB 3.0 interface.
If you connect the unit to a USB hub, it is not guaranteed to work.
Optional Accessories
Part Name
Part Number
Notes
Roller exchange kit
•
•
Paper feed roller
Double feed prevention roller module
KV-SS061
Roller cleaning paper
KV-SS03
Carrier sheet
KV-SS076
Note
•
To purchase separately sold items, contact your dealer.
6
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents
Switching the Background Color of Scanned Images .................................................31
Clearing Paper Jams ..............................................................................48
Operating Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
8
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Before You Start
Installation
Precautions
Illegal Duplication
•
Do not place the unit in direct sunlight, in a cold
draft, or near heating apparatus.
•
Do not place the unit near apparatus which
generate electronic or magnetic noise.
Protect the unit from static electricity.
Do not move the unit immediately from a cold place
to a warm place. It may cause dew.
It is unlawful to make duplication of certain
documents.
Duplicating certain documents may be illegal in
your country/area.
Penalties of fines and/or imprisonment may be
imposed on those found guilty. The following are
examples of items that may be illegal to duplicate
in your country/area.
•
•
•
When the unit is not used over an extended period
of time, turn the unit off, and unplug the power cord.
The unit consumes approximately 0.5 W of
electricity even when the main unit is turned off.
Use only the power cord and the USB cable that are
provided with the unit.
•
•
•
•
•
•
Currency
Bank notes and checks
Bank and government bonds, and securities
Passports, licenses, official or private
documents, identification cards, and the like
Copyright materials, or trademarks without
the consent of the owner
Do not turn ON the unit’s power before installing the
software.
•
•
CD-ROM
•
Do not write or stick paper on the front and/or back
of CD-ROM.
Postage stamps, and other negotiable
instruments
•
Do not touch the data side of the CD-ROM. When
handling the CD-ROM, be careful not to leave
fingerprints or otherwise damage the CD-ROM.
Do not leave the CD-ROM where it is directly
exposed to sunlight or near a heater for extended
periods.
This list is not inclusive, and no liability is
assumed for either its completeness or accuracy.
In case of doubt, contact your legal counsel.
•
•
Notice
Do not throw or bend the CD-ROM.
Install your machine near a supervised area
to prevent illegal duplication from being
made.
Operating Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Roller Cleaning Paper
Security Notice
Using a pair of scissors, open the bag along the dotted The management of documents and scanned data is
line (A), and take out the roller cleaning paper. the responsibility of the user. In particular, pay attention
If the bag is left opened for a long period of time before to the following points.
using it, the alcohol will evaporate. Please use the roller
cleaning paper immediately after opening the bag.
•
Make sure you have the same number of pages for
important documents both before and after
scanning, and take care not to leave any pages in
the scanner.
•
•
Periodically back up important data.
When having your computer or hard disk serviced,
or when disposing of your computer or hard disk,
completely erase any stored image data.
1
Others
•
Make sure to remove paper clips and staples from
Notice
documents before scanning. Failing to do so can
damage the unit, document, or both.
Do not use thinner, benzine, or cleaners containing
abrasives or surfactants, for cleaning the outside of
scanner.
•
Keep the roller cleaning paper out of reach of
small children.
Do not store the roller cleaning paper in direct
sunlight or in a place with a temperature over
40 °C (104 °F).
•
•
•
•
Only use the roller cleaning paper to clean the
rollers.
For details about the roller cleaning paper, refer
to the Material Safety Data Sheet (MSDS).
Please ask your Panasonic sales company
about obtaining the Material Safety Data Sheet.
To purchase the roller cleaning paper
(KV-SS03), please contact your dealer, or call
our Supplies and Accessories department at
1-800-726-2797 (U.S.A. only).
•
KEEP AWAY FROM FIRE.
10
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Check the Accessories
Check that all accessories are included before installing the unit. In the event that an item is missing, please
contact your dealer.
Accessories
Name
Notes
USB cable
Software /
—
Drivers, Applications, Utilities, Documents
Manual CD-ROM
When the unit is shipped, this is stored in the
feed tray.
Mixed batch card guide
Quick Installation Guide
Power cord
—
Two power cords may be included. Use the
power cord appropriate for where you use the
unit.
Note
•
It is highly recommended to keep the original carton and all packing materials. They are necessary
when repacking.
Operating Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Location of Controls
L
o
c
a
t
Main Unit
i
o
n
o
f
Front
C
o
n
t
14
13
r
o
l
1
s
2
3
4
12
11
5
6
10
8
7
9
Document guides
Mixed batch card guide
Manual feed selector
Switches the scanning method between continuous scanning (Auto) and manual scanning (Manual).
Operation panel
Exit tray
Exit extension tray 1
Exit extension tray 2
Exit stopper
Exit guides
Fan exhaust vent
ADF door
ADF door release
Feed tray
Feed extension tray
12
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Location of Controls
Rear
1
2
4
5
3
Security slot
Use a commercially available security cable.
USB connector
USB cable
Connect the USB cable to the scanner and the other end of the USB cable to the computer.
Power cord
AC inlet
Operating Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Location of Controls
Operation Panel and LED Indicators
nKV-S1057C and KV-S1027C
1
2
3
4
5
6
7
8
nKV-SL1066, KV-SL1056, KV-SL1055, KV-SL1036 and KV-SL1035
1
2
3
4
5
6
9
A LED (Red)
Lights when an error occurs.
B LED (Green)
Shows the scanner’s status.
C Power button
Press the power button for more than one second to turn the unit off.
D Cursor button
E Skip button
If you press this button after a double feed is detected and scanning has been paused, the document
(or documents) detected as a double feed will be scanned, and then ejected from the scanner.
Scanning will continue after the document is scanned and ejected.
14
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Location of Controls
F Start/Stop button
•
If you set [Wait Key] for "Manual Feed Mode" in your application software, pushing this button
starts scanning. For details about "Manual Feed Mode", refer to the Image Capture Plus,
TWAIN, or ISIS help.
•
•
During scanning, pushing this button stops scanning.
If you press this button after a double feed is detected and scanning has been paused, the
document (or documents) detected as a double feed will be ejected from the scanner without
being scanned. Scanning will stop.
n KV-S1057C and KV-S1027C only
G LCD
H OK button
If you are using the scanner with Image Capture Plus, you can perform a push scan using the LCD.
Registered jobs are displayed on the LCD. Use the cursor button (D) to select a job. Also, error
codes and messages corresponding to the scanner status are displayed on the LCD.
n KV-SL1066, KV-SL1056, KV-SL1055, KV-SL1036 and KV-SL1035 only
I 7-segment LED
If you are using the scanner with Image Capture Plus, you can perform a push scan using the
7-segment LED. A registered job number is displayed on the 7-segment LED. Use the cursor button
(D) to select a job.
Operating Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Location of Controls
About LED
The status of the scanner is displayed by the LED (Red) (A) and the LED (Green) (B), as shown in the
table below:
A LED (Red)
B LED (Green)
Status
OFF
OFF
ON
Power OFF*1
OFF
Ready mode or Scanning
Sleep mode*2
OFF
Blinking (Slow, Long ON)
Blinking (Slow)
ON
ON
Warning
OFF
Error*3
OFF
Blinking (Fast)
Warming up
OFF
Blinking (Fast, 2 times consecutively)
Double Feed Skip mode
*1
*2
*3
If the power off feature in sleep mode is enabled, and if no operation is performed for a certain period of time, the scanner will be
turned off automatically. Press the power button of the scanner to turn it on. You can enable/disable the power off feature, and change
the time until the scanner turns off in User Utility.
If no operation is performed for 15 minutes or longer, the scanner will enter sleep mode automatically to conserve energy. Press any
button (except the power button) on the scanner’s operation panel to return to ready mode. The time until the scanner enters sleep
mode can be changed in User Utility.
16
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
I
n
s
t
Required Space Around the Scanner
a
l
In order to ensure proper operation, install the unit maintaining the proper distances from surrounding objects,
as shown in the following illustration.
l
a
t
i
o
n
400 mm
(16 in.)
238 mm
(9.4 in.)
272 mm
(10.7 in.)
750 mm
(30 in.)
300 mm
(11.8 in.)
500 mm
(20 in.)
Notice
•
Do not move the unit immediately from a cold place to a warm place. It may cause condensation, which
may damage the unit.
Operating Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installing the Software
Notice
•
Make sure to connect the unit to your computer after installing the software. Connecting the unit to your
computer and turning on the unit’s power before installing the software may influence the software
installation. If you connect the unit to your computer and turn on the unit’s power before installing the
software by mistake, install the software after disconnecting the unit from your computer.
Make sure to log on as an administrator to install the software.
•
The software on the enclosed Software / Manual CD-ROM can be installed on your computer.
You can select from the 2 installation methods below, depending on your needs.
a. Complete: Install all the drivers, applications, utilities and Operating Manual.
b. Custom: Install one of the software or Operating Manual.
Note
•
Normally, it is recommended to select [Complete].
1. Check that the unit has been turned off.
•
If the power is turned on, press and hold the power button for more than one second to turn the unit
off.
2. Insert the Software / Manual CD-ROM into the CD/DVD drive on your computer.
•
•
If you have a feature called "Autorun" activated, the installation process will start automatically.
The setup window will appear.
Note
•
•
If the AutoPlay dialog box is displayed, select [CDRun.exe].
If the setup window does not appear, double-click [CDRun.exe] in the Software / Manual CD-ROM.
3. Check the [Read me first] file.
4. Select the desired installation methods from "Software" on the left side of the screen.
•
18
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Note
•
If you select TWAIN or ISIS, Image Capture Plus will also be installed.
6. Follow the instructions on the screen and complete the installation.
Restart your computer if you are prompted to do so.
•
Operating Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installing the Unit
1. Remove all packing tape and cushioning.
2. Pull out the feed extension tray in the direction of the arrow shown in the illustration below.
3. Set the exit tray.
a. Raise the exit stopper.
20
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
b. Pull out the exit tray (A) and the exit extension trays (B, C).
1
2
3
Notice
•
Do not forcefully pull out the exit stopper, the exit tray, or the exit extension trays. Doing so
may damage them.
4. Plug in the power cord and connect the USB cable.
5. Press the power button to turn ON the unit’s power.
•
•
The LED (Green) will flash and then turn on.
If the hardware wizard appears, follow the on-screen instructions to complete installation.
Operating Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Viewing Operating Manual and Help Installed
If the manuals and software that were included on the Software / Manual CD-ROM have been installed on your
computer, you can use the following procedure to view the Operating Manual and the software’s help.
To view the Operating Manual
1. Select [All Programs] ® [Panasonic] ® [Scanner Manuals].
2. Select the manual.
•
The manual will open.
Note
•
In Windows 8, select the [Panasonic Document Scanner] section on the Apps screen.
To view the help
Note
•
We recommend that you view the help using Internet Explorer® 6.0 or later for Windows.
For Image Capture Plus
1. Select [All Programs] ® [Panasonic] ® [Image Capture Plus] ® [Image Capture Plus Help].
For User Utility or Scan Button Setting Tool
1. Select [All Programs] ® [Panasonic] ® [Scanner Tools].
2. Select that item’s help.
Note
•
In Windows 8, select the [Panasonic Document Scanner] section on the Apps screen.
For TWAIN or ISIS
1. Click the help button on any driver screen.
22
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
O
p
e
r
Preparing Documents
a
t
Notice
i
•
Make sure to remove paper clips and staples from documents before scanning. Failing to do so can
damage the unit, document, or both.
o
n
•
•
•
•
It is recommended to confirm that documents and cards are suitable for scanning (paper size,
thickness, type, etc.) before scanning them.
Before feeding, ensure that the document is not creased or folded. If the document is creased or folded,
a paper jam or damage to the document may occur.
When scanning important documents, confirm that the number of scanned images matches the number
of pages in the feed tray. Also, check the condition of the scanned documents.
Remove documents from the exit tray after they have been scanned.
Compatible Paper Types
Paper size:
Width
Length
The compatible paper sizes for this unit are as follows.
Width
48 – 216 mm (1.9 – 8.5 in.)
When feeding one sheet: 54 mm – unlimited (2.1 in. – unlimited)*1
When feeding multiple sheets: 54 – 356 mm (2.1 – 14 in.)
Length
*1
Using "Long Paper", you can scan long documents by splitting them into smaller parts. For details about "Long Paper", refer to the
Image Capture Plus, TWAIN, or ISIS help.
Paper thickness:
0.04 – 0.5 mm (1.6 – 19.7 mils)
Note: 1 mil = 0.001 in.
Paper weight:
20 – 413 g/m² (5 – 110 lb.)
Operating Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Paper capacity for the feed tray:
Number of
sheets
Paper length (L)
Combined thickness
Paper weight
64 g/m² (17 lb.)
130
100
100
80
High-quality woodfree paper
54 mm £ L £ 297 mm
(2.1 in. £ L £ 11.7 in.)
10 mm
(0.4 in.)
75 g/m² (20 lb.)
High-quality woodfree paper
80 g/m² (21 lb.)
High-quality woodfree paper
64 g/m² (17 lb.)
High-quality woodfree paper
297 mm < L £ 356 mm
(11.7 in. < L £ 14 in.)
8 mm
(0.31 in.)
75 g/m² (20 lb.)
High-quality woodfree paper
80
80 g/m² (21 lb.)
High-quality woodfree paper
80
Recommended paper types:
•
•
•
High-quality woodfree paper
Bond paper
•
•
•
Recycled paper
OCR paper
Newspaper
Bank checks
Note
•
•
High-quality woodfree paper is the recommended paper type.
Documents must also meet the following conditions:
Feeding direction
Less than
5 mm
Curl
(0.2 in.)
Feeding direction
Less than
5 mm
(0.2 in.)
Folding
24
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Compatible Card Types
The compatible card types for this unit are as follows.
ISO format card:
Size:
85.6 ´ 54 mm (3.4 ´ 2.1 in.)
Thickness:
0.76 mm (0.03 in.)
•
•
•
•
Embossed cards are also compatible. When scanning embossed cards, it is recommended to place them
in landscape orientation with the side to be scanned facing up.
A maximum of 3 cards can be loaded on the feed tray. When loading, ensure that the embossed portions
of cards do not stick together.
Use the landscape orientation when scanning an embossed card. If the scanning fails, place the card
upside down, and then try again.
time.
Operating Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Compatible Bound Documents (Manual Scanning Only)
Bound documents can be scanned by setting the manual feed selector to manual scanning (Manual). You can
use an optional carrier sheet (KV-SS076) to scan passports using manual scanning.
Passport size:
The passport sizes compatible with this unit are as follows.
Width:
140 mm (5.5 in.) or less
190 mm (7.5 in.) or less
2.6 mm (0.1 in.) or less
Length:
Thickness:
Scanning passports
1. Set the manual feed selector to manual scanning (Manual).
26
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
2. Put the passport in a carrier sheet.
•
Open the passport (A) to the page you want to scan, and then put the thinner part (the opened half
with less pages) in the carrier sheet (B) first, as shown in the illustration.
•
The corner of the thinner part of the passport should be inserted into the corner of the carrier sheet.
2
1
3. Place the carrier sheet (A) on the feed tray with the surface to be scanned facing down.
•
Adjust the document guides (B) to the size of the carrier sheet to be scanned.
1
2
Operating Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
4. Insert the carrier sheet (A) until it stops as shown in the illustration.
1
Note
•
When manual scanning (Manual) is selected, make sure to insert the documents until they come
into contact with the paper feed roller.
5. Start scanning.
Note
•
If the rollers are dirty, the scanned image will be stretched or distorted. In such cases, clean the
rollers.
•
If vertical streaks appear on the scanned image, clean the scanning glasses and the carrier sheet.
Vertical streaks that appear may be caused by scratches on the carrier sheet. If vertical streaks
appear after cleaning the scanning glasses and the carrier sheet, flip over the carrier sheet to the
other side, or replace the carrier sheet, and then scan the documents.
28
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Incompatible Documents
The following types of documents may not scan properly:
•
•
•
•
•
•
•
•
Torn or frayed documents
Curled, wrinkled or folded documents
Carbon paper
Perforated or punched paper
Non-rectangular or irregularly shaped paper
Coated paper
Bound or glued documents
Chemical paper such as carbonless copy paper
If papers like this are scanned, the rollers will need to be cleaned frequently and the lifetime of the rollers
may be shortened.
•
•
Paper with wood content
Photographs
Photographs may be scratched or damaged.
•
Extremely smooth, shiny paper, or paper that is highly textured
Notice
•
Paper with a glossy surface such as coated paper or photographs that are susceptible to damage such
as scratching.
•
Scanning the following kinds of documents may contaminate the inside of the scanner or adversely
influence the lifetime of the rollers. When scanning the following kinds of documents, clean the inside
of the scanner frequently.
–
–
Documents with toner or graphite (pencil) powder
Documents treated chemically or containing impurities
Do not scan the following types of paper:
•
•
•
•
•
•
•
Documents out of specified size, thickness, and weight
Thermal or photosensitive paper
Cloths or metallic sheets
Transparent or partially transparent documents such as OHP sheet, tracing paper, plastic film, etc.
Documents containing hard attachments such as metal or plastic (ex. clips or staples)
Document with wet ink or cinnabar seal ink
Damaged or notched documents or cards
Operating Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Notes about Documents for Scanning
•
Depending on the paper type, scanning results may be poor when you scan incompatible documents, or
even documents that should be compatible.
If scanned images are skewed, paper jams occur, or double feeding occurs, try scanning again after doing
the following:
–
–
–
Clean the inside of the scanner (page 51)
Reduce the number of sheets of paper loaded on the feed tray.
Change the orientation of documents placed in portrait orientation to landscape orientation, or vice
versa.
In the scan settings, set "Feeding Speed" to [Slow].*1
Scan the documents using manual scanning.
–
–
*1
For details about configuring the scan settings, refer to the Image Capture Plus, TWAIN, or ISIS help.
Notes about Double Feed Detection
This unit uses an ultrasonic sensor to detect double feeding (where two or more sheets of a document are fed
at the same time).
•
•
Double feeding cannot be detected with unsupported paper types.
Even with supported types of cards, scanning them in portrait orientation may result in the detection of a
double feed. In this case, try scanning them in landscape orientation, or disable the double feed detection.
Documents must be 70 mm (2.8 in.) or longer for double feed detection to function.
•
30
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Switching the Background Color of Scanned Images
Using the software, you can switch the background color of scanned images between white and black.
For details, refer to the Image Capture Plus, TWAIN, or ISIS help.
Operating Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continuous Scanning (Auto) and Manual Scanning
(Manual)
You can select either continuous scanning (Auto) or manual scanning (Manual) by using the manual feed
selector. Bound documents can be scanned by setting the manual feed selector to manual scanning (Manual).
Continuous scanning (Auto)
This setting is for feeding documents one page at a time automatically.
Manual scanning (Manual)
This setting is for feeding bound and other documents manually without separating them.
Notice
•
When scanning important documents or bound documents, feed them manually.
32
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Mixed Batch Card Guide
No adjustment to the document guide is required when using the mixed batch card guide. The mixed batch
card guide prevents a card from skewing when scanning paper documents and a card simultaneously.
Installing the mixed batch card guide
The mixed batch card guide is stored inside the feed tray. Install the mixed batch card guide as shown in the
following illustration.
1. Remove the feed tray (A) from the unit.
•
Remove the left side of the feed tray (B) first as shown in the illustration.
2
1
2. Pull out the mixed batch card guide (B) from the feed tray (A).
2
1
Operating Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
3. Attach the feed tray (A) to the unit.
1
4. Attach the mixed batch card guide (A) to the unit.
1
34
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Removing the mixed batch card guide
Remove the mixed batch card guide as shown in the following illustration.
1. Remove the mixed batch card guide (A) from the unit.
1
2. Remove the feed tray (A) from the unit.
•
Remove the left side of the feed tray (B) first as shown in the illustration.
2
1
Operating Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
3. Attach the mixed batch card guide (B) to the feed tray (A).
2
1
4. Attach the feed tray (A) to the unit.
1
36
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Using the Mixed Batch Card Guide
Set paper documents on the feed tray, and a card on the mixed batch card guide respectively.
•
•
The card set on the mixed batch card guide is fed after completing the paper document scanning.
The mixed batch card guide is suitable for the following card type.
ISO format card:
Size:
85.6 ´ 54 mm (3.4 ´ 2.1 in.)
Thickness:
0.76 mm (0.03 in.)
Embossed card is also available.
•
•
•
•
Set the card in landscape orientation.
A maximum of 3 cards can be set in the mixed batch card guide.
Ensure that the embossed portions of cards do not stick together.
If acceptable results cannot be obtained, try changing the scanning orientation or reversing the scan face
of the card, and then perform scanning again.
Note
•
•
When using the mixed batch card guide, the document guides cannot be adjusted to less than A5 size.
Make sure that the total height of the paper on the feed tray does not exceed 2 mm (0.08 in.). (This is
equivalent to about 20 sheets at 80 g/m² [21 lb.].)
Operating Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
2. Fan the documents.
Documents that have been stapled together or stacked together (as in a file folder) will need to be
•
separated.
Fan the stack of documents to separate all the edges.
Hold both ends and bend the documents as shown in the illustration.
To flatten the documents, hold firmly and pull them apart as shown in the illustration.
1
2
3
Repeat these steps as necessary.
3. Carefully align the documents.
•
The documents feed better when the leading edges are aligned slantwise as shown in the illustration.
1
2
Operating Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
4. Place the documents on the feed tray with the side to be scanned facing down.
•
•
Set the leading edge of documents as shown in the illustration (A).
Insert the documents slowly until they stop.
1
Note
•
The height of the documents should not exceed the limit mark (
Exceeding the limit mark may cause a paper jam or skewing.
) on the document guide.
5. Adjust the document guides (A) to the size of the documents to be scanned.
1
40
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
6. Hold the exit stopper and adjust the exit extension trays (A, B) to match the size of the scanned
documents.
3
1
2
Note
•
When the documents are curled or a paper jam occurs, fold up the exit guides (C) and then resume
scanning.
3
7. Open your scanning application and scan the documents.
•
•
For details about the application, refer to the help of each application.
You can also start up applications automatically to scan documents (push scan). For details about push
Operating Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Performing a push scan
The following push scan functions are available for each scanner as shown below:
KV-SL1066
KV-SL1056
KV-SL1055
KV-SL1036
KV-SL1035
KV-S1057C
KV-S1027C
Yes
Yes
No
Yes
No
Yes
Touch Free Scanning
Setting the application to start up
Set whether an application will automatically start up and select under which conditions it will start up in the
Scan Button Setting Tool.
1. Double click the ( ) icon in the notification area of the task bar to open the Scan Button Setting Tool.
•
In Windows 8, open the Scan Button Setting Tool on the Desktop screen.
2. Select Touch Free Scanning for the condition to automatically start up the application.
3. Select the application to start up.
Note
•
For details about the Scan Button Setting Tool, refer to the Scan Button Setting Tool help.
Setting the scanning conditions
Scanning conditions are set on the setting screen of each application. For details about the setting screen of
each application, refer to the manual or help for that application.
Note
•
Press and hold the OK button for more than 2 seconds to open the application setting screen.
(KV-S1057C and KV-S1027C only)
•
Press and hold the Start/Stop button for more than 2 seconds to open the application setting screen.
(KV-SL1066, KV-SL1056, KV-SL1055, KV-SL1036 and KV-SL1035 only)
Performing Touch Free Scanning
1. Place the documents on the feed tray.
•
Scanning will start.
42
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Push scan using the LCD
If you are using a KV-S1057C or KV-S1027C with Image Capture Plus, you can perform a push scan using
the LCD. Registered jobs are displayed on the LCD. Use the cursor button (A) to select a job.
Note
•
•
Register jobs in advance. For details about registering jobs, refer to the Image Capture Plus help.
The group name is displayed on the first line, and the job name is displayed on the second line of the
LCD.
1
2
1. Place the documents on the feed tray.
2. Use
or
of the cursor button (A) to select a group.
3. Use or of the cursor button (A) to select a job.
4. Press the OK button (B).
•
Scanning will start.
Operating Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Push scan using the 7-segment LED
If you are using a KV-SL1066, KV-SL1056, KV-SL1055, KV-SL1036 or KV-SL1035 with Image Capture Plus,
you can perform a push scan using the 7-segment LED. A registered job number is displayed on the 7-segment
LED. Use the cursor button (A) to select a job number.
Note
•
Register jobs in advance. For details about registering jobs, refer to the Image Capture Plus help.
1
2
1. Place the documents on the feed tray.
2. Use or of the cursor button (A) to select a job number.
3. Press the Start/Stop button (B).
•
Scanning will start.
44
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Checking events
Check the following if an application does not start up after being set.
1. Display the Scan properties screen.
•
•
•
If you are using Windows 8 / Windows 7:
[Control Panel] ® [View devices and printers], right-click the scanner icon, and display the [Scan
properties] screen.
If you are using Windows Vista:
[Control Panel] ® [Scanners and Cameras], select the scanner icon, and then click the Properties
button.
If you are using Windows XP:
[Control Panel] ® [Scanners and Cameras], right-click the scanner icon, and display the Properties
screen.
2. Click the [Events] tab.
3. Check that Scan Button Setting Tool is selected as the program to start for each event.
•
If an application other than Scan Button Setting Tool is selected, change the application to Scan Button
Setting Tool.
4. Click [OK].
5. Restart the computer.
Operating Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Using Control Sheets
Placing a control sheet in the middle of documents lets you change the scanning conditions for pages scanned
after the control sheet. Also, you can change the folder used to save the scan data of documents scanned
after the control sheet.
•
Print out control sheets from the included CD-ROM.
Documents
Control sheet
Code
Documents
Control sheet functions
Simplex, Duplex, Binary, 256 level gray, Color, Dynamic Threshold, Dither, Error diffusion, Separation
Sheet
•
•
For details about control sheets, refer to "Detect Control Sheet" in the Image Capture Plus, TWAIN, or
ISIS help.
For details about separation sheets, refer to "Detect Separation Sheet" in the Image Capture Plus,
TWAIN, or ISIS help.
46
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
About Printing Control Sheets
•
•
Print the control sheet at the specified size; do not enlarge or reduce the size.
When printing the control sheet, make sure that the pattern is 25 mm (1 in.) from the top of the page and
centered horizontally.
Center of the page
25 mm
(1 in.)
<Example A4 printout>
•
•
Use the control sheet that is the same size as the document you are scanning.
Be careful not to get the control sheet dirty. Do not fold or crease the control sheet. Scanning will not be
performed properly.
•
For details about control sheets, refer to "Detect Control Sheet" in the Image Capture Plus, TWAIN, or
ISIS help.
Printing control sheets
Note
•
•
In order to print control sheets, Adobe® Reader® must be installed on your computer.
Refer to the instruction manual for your printer for details about changing print settings.
1. Insert the included CD-ROM into the CD/DVD drive on your computer.
•
•
If you have a feature called "Autorun" activated, the installation process will start automatically.
The setup window will appear.
Note
•
•
If the AutoPlay dialog box is displayed, select [CDRun.exe].
If the setup window does not appear, double-click [CDRun.exe] in the Software / Manual CD-ROM.
2. Select [Control Sheet] from "Documents" on the right side of the screen.
3. Print the control sheets at the same size as your document.
Operating Manual
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
C
l
e
a
r
Clearing Paper Jams
i
Torn paper, thin paper or paper that is creased on the top edge may cause paper jams. If a paper jam occurs,
remove the jammed sheet according to the following procedure.
n
g
P
a
p
e
r
1. Remove all documents from the feed tray.
2. Press the ADF door release (A), and open the ADF door (B).
J
a
m
s
2
1
3. Remove the jammed document.
•
If the document is jammed in the feed tray area, pull it backwards as shown in the illustration.
48
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
•
If the document is jammed in the exit area, pull it forward as shown in the illustration.
4. Close the ADF door.
•
Push both sides of the ADF door down slowly until it clicks into place.
Notice
•
Close the ADF door after confirming that no documents remain inside the unit.
Operating Manual
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
C
a
r
e
a
n
d
M
a
i
Cleaning the Outside of the Scanner
Notice
•
•
Before moving the unit, be sure to unplug the power cord and USB cable.
Do not use commercially available cleaners, detergent, thinner, or benzine. (Doing so may cause
deformation, discoloration or damage.)
•
Clean the scanner at least once a month.
n
t
e
n
a
n
c
e
1. Clean the outside of the scanner with a soft, slightly damp cloth.
2. Remove dirt and dust from the fan exhaust vent (A) with a brush.
1
50
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
Cleaning the Inside of the Scanner
Note
•
Clean the inside of the scanner when approximately 6,000 sheets have been scanned. The time for
cleaning may differ depending on documents you scan. To maintain proper scanning, clean the scanner
parts frequently.
•
•
•
•
Clean the rollers if paper jamming or double feeding occurs frequently.
If double feed detection does not function properly, clean the double feed detectors.
Clean the scanning glasses when vertical streaks appear on the scanned images.
Be careful not to damage any parts of the unit.
1. Prepare the following cleaning supplies.
Soft and dry cloth
Used to clean the conveyor and scanning glasses.
Used to clean the double feed detectors and the starting
sensors.
Thin cotton swab
Used to clean the rollers. Use of the roller cleaning paper is
recommended. If you do not have the roller cleaning paper, use
a soft cloth with a small amount of isopropyl alcohol or water.
Do not use commercially available cleaners, detergent,
thinner, or benzine. (Doing so may cause deformation,
discoloration or damage.)
Roller cleaning paper (KV-SS03)
2. Press the ADF door release (A), and open the ADF door (B).
2
1
Operating Manual
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
3. Clean the conveyor, scanning glasses, double feed detectors, starting sensors and rollers.
•
Clean the parts in the following order: conveyor and scanning glasses, double feed detectors and
starting sensors, rollers.
•
For details about cleaning, refer to the following:
–
–
–
4. Close the ADF door.
•
After cleaning, push both sides of the ADF door down slowly until it clicks into place.
Notice
•
If roller cleaning notifications via the After Clean Roller Counter are enabled, reset the After Clean
Roller Counter in User Utility to 0.
For details, refer to the User Utility help.
52
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
Cleaning the Rollers
Use the roller cleaning paper (KV-SS03) (page 10) to wipe dirt off from the surfaces of all rollers.
Notice
•
Be careful not to damage any parts of the unit.
1. Open the double feed prevention roller cover (A).
1
2. Remove the double feed prevention roller.
•
While pushing the latch (A) to the right side as the direction indicated by the arrow, remove the double
feed prevention roller (B) in the direction of the arrow. Then, pull out the left shaft (when facing it) from
the notch in the roller mount.
2
1
Operating Manual
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
3. Use the roller cleaning paper to clean the surface of the double feed prevention roller.
•
Wipe the entire surface of both rollers.
4. Install the double feed prevention roller.
•
Align the shaft that is shaped as indicated by A with the notch in the roller mount (B), and then insert
the shaft in the notch. Push the shaft on the opposite side (C) until it clicks into place.
2
1
3
56
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
5. Close the double feed prevention roller cover (A) firmly.
1
Notice
•
Be sure to close the double feed prevention roller cover until it clicks into place.
6. Open the paper feed roller cover (A).
1
Operating Manual
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
7. Use the roller cleaning paper to clean the paper feed roller.
•
Wipe the rollers from one end to the other (in the direction of the arrow) all the way around them, as
shown in the illustration.
8. Close the paper feed roller cover firmly.
Make sure to close both sides of the paper feed roller cover until they click into place.
•
58
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
9. Use the roller cleaning paper to clean the surface of the conveyor rollers (A) and exit rollers (B).
•
Wipe the rollers from one end to the other (in the direction of the arrow) all the way around them, as
shown in the illustration.
•
Cleaning Mode can be used to help cleaning the conveyor rollers and the exit rollers. Cleaning Mode
can be set in User Utility. During Cleaning Mode, the conveyor rollers and the exit rollers rotate a small
amount every time the Start/Stop button on the scanner is pressed.
2
1
Note
•
•
Do not touch the rollers while they are rotating.
Use Cleaning Mode only for cleaning the conveyor rollers and exit rollers.
10. Use the roller cleaning paper to clean the surface of the free rollers (A).
•
Wipe the rollers from one end to the other (in the direction of the arrow) all the way around them, as
shown in the illustration. Use your finger to rotate the roller and wipe dirt off of the entire surface of the
roller.
1
Note
•
If misfeeding or double feeding occurs after cleaning or replacing the rollers, the rollers may not be
installed properly. Confirm the installation conditions again.
Operating Manual
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
Replacing the Rollers
As a rough guideline, we recommend to replace the paper feed roller and double feed prevention roller module
after scanning 250,000 sheets of paper. ("250,000 sheets" is based on scanning high-quality woodfree paper.
Depending on the type of paper and other factors, the actual lifetime for the rollers will differ.)
In User Utility, you can check the number of sheets that have been scanned.
1. Press the ADF door release (A), and open the ADF door (B).
2
1
2. Open the double feed prevention roller cover (A).
1
60
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
3. Remove the double feed prevention roller.
•
While pushing the latch (A) to the right side as the direction indicated by the arrow, remove the double
feed prevention roller (B) in the direction of the arrow. Then, pull out the left shaft (when facing it) from
the notch in the roller mount.
2
1
4. Take out the new double feed prevention roller module in the optional roller exchange kit.
5. Install the double feed prevention roller.
•
Align the shaft that is shaped as indicated by A with the notch in the roller mount (B), and then insert
the shaft in the notch. Push the shaft on the opposite side (C) until it clicks into place.
2
1
3
Operating Manual
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
6. Close the double feed prevention roller cover (A) firmly.
1
Notice
•
Be sure to close the double feed prevention roller cover until it clicks into place.
7. Open the paper feed roller cover (A).
1
62
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
8. Lift up the gear (A) on the left side of the paper feed roller, and then remove the paper feed roller.
1
9. Remove the rubber rollers from the paper feed roller shaft.
•
Push the tab (A) to remove the rubber roller (B) from the paper feed roller shaft. Remove the other
rubber roller (C) in the same way.
1
3
2
Operating Manual
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
10. Take out the new paper feed roller in the optional roller exchange kit.
11. Install the two new rubber rollers onto the paper feed roller shaft.
•
After confirming the tabs (A) of both rubber rollers are facing outwards, insert the rubber rollers onto
the paper feed roller shaft until they click into place.
1
1
Notice
•
Inserting a rubber roller with the tab facing inwards may damage the roller.
12. Install the paper feed roller with the new rubber rollers.
•
Insert the short side of the paper feed roller shaft (A) to the roller mount, and then insert the gear
(B) in the direction indicated by the arrow.
2
1
64
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
13. Close the paper feed roller cover (A) firmly.
1
Notice
•
•
Make sure to close both sides of the paper feed roller cover until they click into place.
After installing the paper feed roller, confirm that the paper feed roller can rotate in the feeding
direction.
14. Close the ADF door.
•
Push both sides of the ADF door down slowly until it clicks into place.
15. Reset the After Replace Roller Counter in User Utility to 0.
•
For details, refer to the User Utility help.
Note
•
If misfeeding or double feeding occurs after cleaning or replacing the rollers, the rollers may not be
installed properly. Confirm the installation conditions again.
Operating Manual
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
A
p
p
e
n
d
i
Troubleshooting
If a problem occurs while the scanner is being used, check the following items and check the scanner status
in User Utility. If the unit still malfunctions, turn it OFF, unplug the power cord and call for service.
x
Symptom
Possible Cause
Remedy
The LED (Green) does not
light when the unit’s power is The power cord is not plugged in.
turned ON.
Insert the power plug firmly.
The scanner is not connected to the
computer correctly.
Connect the USB cable correctly.
Uninstall the software from the
The computer does not
recognize the scanner.
The scanner is connected via USB
Do not connect via USB hub.
The scanner is not functioning hub.
correctly.
There is a problem with the USB
Make sure to use the included USB
cable.
cable.
The unit’s power was turned OFF
because no operation was performed
for a certain period of time.
Press the power button to turn ON the
unit’s power.
The scanner is connected over a USB
1.1 connection.
Scan speed is slow.
Connect over USB 2.0 / USB 3.0.
Load the document correctly.
The document is not loaded properly.
The document has been
loaded on the feed tray, but
the scanner does not start
scanning.
The sensor cannot detect the
document as the edge of the
document is curled.
66
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Symptom
Possible Cause
Remedy
The paper feed roller or double feed
prevention roller have become worn
down.
Replace the paper feed roller or
double feed prevention roller.
Clean the double feed detectors.
The double feed detectors are dirty.
Right and left sides of the document
to be scanned are not the same in
height, because of curling or folding.
load it again after reducing the number
of sheets.
Make a copy of the document on
paper of a compatible type and
thickness (page 23), and then scan
the copy.
The document is printed on an
unsupported type of paper or thick
paper.
Double feeding occurs
frequently.
Make a copy of the document on
paper of a compatible size (page 23),
and then scan the copy.
The length of the paper is too short.
Remove sheets until the sheets on the
Too many sheets are set on the feed
feed tray are under the limit mark on
tray.
the document guide.
The documents are not fed
one at a time, but in bunches. manual.
The scanning method is set to
Select automatic scanning using the
Either disable the double feed
detection function or set the cards in
landscape orientation.
A double feed is detected
when scanning cards.
The cards are set in portrait
orientation.
The document is wrinkled.
The rollers are dirty.
Smooth out the document.
Paper jams occur frequently.
Remove sheets until the sheets on the
Too many sheets are set on the feed
feed tray are under the limit mark on
tray.
the document guide.
Scanned documents have
been rolled up in the exit tray
area when using the exit
guides.
Scan the documents with the exit
The documents are curved or curled.
The document guides are not
adjusted to the size of the document Adjust the document guides properly
to be scanned, or the document to be to the size of the document to be
scanned is set slanted on the feed
tray.
Scanned image is skewed.
Right and left sides of the document
to be scanned are not the same in
height, because of curling or folding.
load it again after reducing the number
of sheets.
Operating Manual
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Symptom
Possible Cause
Remedy
The image for a scanned
document is blank.
The document to be scanned was
loaded upside down.
Load the document correctly.
Vertical streaks appear on the
scanned document.
Clean the scanning glasses.
The scanning glasses are dirty.
The scanning glasses are dirty.
The scanning density is
uneven.
Clean the scanning glasses.
The settings of the computer monitor
are wrong.
Adjust the computer monitor settings.
The color of the scanned
document is extremely
different from the original
document.
Depending on the documents
scanned, the color of documents may
not be scanned properly. For
example, the color of a highlighter pen
may be scanned lighter than it
appears.
Setting the value for Chroma higher in
the scanning conditions may solve
this problem.
Dark spots or noise appear on
the scanned documents.
Clean the scanning glasses.
The scanning glasses are dirty.
The scanning resolution settings,
combined with patterns within the
scanned image, may cause this
problem.
There is noise or wave
patterns (moire pattern) on
the scanned image.
Change the scanning resolution, and
perform scanning again.
If the length of documents are less
than about 148 mm (5.8 in.), feeding
speed control will be activated for
exiting documents; this is normal
behavior.
The sound made by paper
being ejected is higher than
usual when you scan short
documents.
—
If you still experience problems after following these suggestions, please contact our Technical Support
Department at 1-800-726-2797 for further assistance. (U.S.A. only)
68
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Error Messages (KV-S1057C and KV-S1027C only)
Error codes corresponding to the scanner status are displayed on the LCD.
Also, when the scanner is connected to a computer, simple messages are displayed on the LCD.
For details about the error codes and messages, check in User Utility.
Error Code
Cause
Remedy
The paper has jammed in the feed tray
area.
Open the ADF door, and remove the paper.
Clean the sensors.
U11
U12
The sensors are dirty.
The paper has jammed in the exit tray area. Open the ADF door, and remove the paper.
U16
The sensors are dirty.
Clean the sensors.
Open the ADF door, and remove all the
paper left inside.
Paper has been left in the scanner.
The sensors are dirty.
U18
U23
Clean the sensors.
Open the ADF door, and remove the
jammed paper.
A double-feed error has occurred.
The ADF door is open.
U30
Fxx
Close the ADF door.
Contact your dealer.
A system error has occurred.
Operating Manual
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Uninstalling the Software
If you want to remove the software that is installed on your computer, follow the procedure below to uninstall
them.
1. In [Control Panel], open [Uninstall a program].
•
In Windows XP, select [Add or Remove Programs].
2. Uninstall the following software programs.
Program Name
Publisher
Image Capture Plus
Panasonic System Networks Co., Ltd.
Panasonic System Networks Co., Ltd.
Panasonic System Networks Co., Ltd.
Panasonic System Networks Co., Ltd.
Panasonic System Networks Co., Ltd.
Panasonic System Networks Co., Ltd.
Scan Button Setting Tool
IDR Engine
Panasonic Scanner Manuals
Panasonic Document Scanner Device Driver
MCD
KV-S1057C KV-S1027C ISIS Driver
KV-SL1066/1056/1055/1036/1035 ISIS Driver
Panasonic System Networks Co., Ltd.
Panasonic System Networks Co., Ltd.
KV-S1057C KV-S1027C TWAIN Driver
KV-SL1066/1056/1055/1036/1035 TWAIN Driver
Panasonic Scanner User Utility
OCR Engine
Panasonic System Networks Co., Ltd.
Panasonic System Networks Co., Ltd.
3. Follow the instructions on the screen.
70
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Repacking Instructions
It is highly recommended that you keep the original carton and ALL packing materials. If you need to transport
or ship the scanner, please follow these instructions.
Note
•
•
•
Improper repacking of the scanner may result in a service charge to repair the scanner.
Please use the original carton and all of the original packing materials.
The scanner should be handled in the correct (horizontal) position.
Required Materials
•
•
Original scanner carton and packing materials
Shipping tape and scissors
1. Unplug the power cord and disconnect the USB cable.
2. Pack the scanner.
1
3
2
A Quick Installation Guide and Software / Manual CD-ROM
B USB cable
C Power cord
Operating Manual
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Specifications
Scanning
KV-S1057C
KV-SL1066
KV-S1027C
KV-SL1056
Item
KV-SL1055
KV-SL1036
KV-SL1035
Scanning face
Scanning method
Scanning size
Duplex
Color CIS (600 dpi)
216 mm (8.5 in.)
A4 / Letter
Simplex
65
45
40
35
30
Binary / color
pages/min.
pages/min.
pages/min.
pages/min.
pages/min.
(200 dpi, 300 dpi)
Scanning
speed*1
A4 / Letter
Duplex
130
90
80
70
60
Binary / color
(200 dpi, 300 dpi)
images/min.
images/min.
images/min.
images/min.
images/min.
100 – 600 dpi (1 dpi step)
1,200 dpi (Interpolated)
Scanning resolution
Optical: 300 dpi / 600 dpi (Automatic switch)
48 – 216 mm (1.9 – 8.5 in.)
Width
When feeding one sheet: 54 mm – unlimited (2.1 in. – unlimited)
When feeding multiple sheets: 54 – 356 mm (2.1 – 14 in.)
Length*3
0.04 – 0.5 mm (1.6 – 19.7 mils)
Note: 1 mil = 0.001 in.
Thickness
Weight
Paper*2
20 – 413 g/m² (5 – 110 lb.)
The height of all the documents on the tray should be less than 10 mm (0.4 in.).
130 sheets (64 g/m² [17 lb.] High-quality woodfree paper)
100 sheets (75 g/m² [20 lb.] High-quality woodfree paper)
100 sheets (80 g/m² [21 lb.] High-quality woodfree paper)
Feed capacity
Format
ISO format
Size
85.6 ´ 54 mm (3.4 ´ 2.1 in.)
0.76 mm (0.03 in.)
Card*4
Thickness
Feed capacity
3 cards on the feed tray or on the mixed batch card guide
250,000 sheets
Roller replacement*5
•
dpi: dots per inch
*1
The scanning speed differs depending on the host computer, the operating system, the application, the measuring method, the quantity of data in
the image, and the paper type. The scanning speed depends on a measuring method of Panasonic.
*2
*3
Using "Long Paper", you can scan long documents by splitting them into smaller parts. For details about "Long Paper", refer to the Image Capture
Plus, TWAIN, or ISIS help.
*4
*5
"Weight in pounds" of paper represents the weight of 500 (432 ´ 559 mm [17 ´ 22 in.]) sheets.
72
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
General
KV-S1057C
KV-SL1066
KV-S1027C
KV-SL1056
Item
KV-SL1055
KV-SL1036
KV-SL1035
External dimensions
(Width ´ Depth ´ Height)
300 ´ 272 ´ 238 mm (11.8 ´ 10.7 ´ 9.4 in.)
Weight
4 kg (8.8 lb.)
AC100 – 125 V, 50/60 Hz, 0.8 A
AC220 – 240 V, 50/60 Hz, 0.5 A
Power requirement*1
Scanning
40 W or less
8 W or less
35 W or less
8 W or less
35 W or less
8 W or less
35 W or less
8 W or less
35 W or less
8 W or less
Ready
Power
consumption
(For AC100 –
125 V models)
3.0 W or less (For KV-S1057C and KV-S1027C)
2.9 W or less (For KV-SL1066, KV-SL1056, KV-SL1055, KV-SL1036 and
KV-SL1035)
Sleep
Power OFF
Scanning
Ready
0.5 W or less
40 W or less
8 W or less
0.5 W or less
35 W or less
8 W or less
0.5 W or less
35 W or less
8 W or less
0.5 W or less
35 W or less
8 W or less
0.5 W or less
35 W or less
8 W or less
Power
consumption
(For AC220 –
240 V models)
3.0 W or less (For KV-S1057C and KV-S1027C)
2.9 W or less (For KV-SL1066, KV-SL1056, KV-SL1055, KV-SL1036 and
KV-SL1035)
Sleep
Power OFF
0.5 W or less
0.5 W or less
0.5 W or less
0.5 W or less
0.5 W or less
Temperature: 5 – 35 °C (41 – 95 °F)
Humidity: 20 – 80 % RH
Operating environment
Storage environment
Temperature: -10 – 50 °C (14 – 122 °F)
Humidity: 8 – 75 % RH
USB 3.0 (For KV-S1057C and KV-S1027C)
USB 2.0 (For KV-SL1066, KV-SL1056, KV-SL1055, KV-SL1036 and KV-SL1035)
Interface
*1
The power requirement differs depending on the country/area. Do not use a power source that does not meet the power source specifications
marked on the unit. The power source specifications of this unit are listed on the rating name plate.
Operating Manual
73
Download from Www.Somanuals.com. All Manuals Search And Download.
© Panasonic System Networks Co., Ltd. 2014
PNQX6995ZA DD0914HS0
Download from Www.Somanuals.com. All Manuals Search And Download.
|