Operating Instructions
High-Power Cassette Player/Receiver with Changer Control
CQ-RG131W
R
• Please read these instructions carefully before using this product and save this manual for future use.
•
Download from Www.Somanuals.com. All Manuals Search And Download.
................................................ 3
..................................... 22
..................................... 24
....................... 26
................................................ 34
................................................ 36
............................................ 37
................................................ 38
.................................................... 39
....................................................... 39
....................................................... 39
................... 28
..................................... 30
....................................................... 31
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
Power and Sound Controls
1
CQ-RG131W
Power
Turn the key in the ignition until the accessory indicator lights.
Press [PWR] to switch on the power.
Volume
●
Press [VOL ] or [VOL ] to increase or decrease volume.
j
i
Volume Level
0 to 39
●
Press [VOL ] or [VOL ] for more than 0.5 second to change
j
i
numeric levels on the display rapidly.
CQ-RG131W
Mute
●
Press [MUTE] mute the sound completely.
“MUTE” blinks while this operation.
●
●
Press [MUTE] again to cancel.
Press and holdCQ-RG131W
Tone Enhancement
●
Press and hold [MUTE] (LOUD) for more than 2 seconds to
enhance bass and treble tones when listening at low or medium
volume.
●
Press and hold [MUTE] (LOUD) for more than 2 seconds again
to deactivate when listening at higher volumes.
Note: This unit is equipped with an anti-volume-blast circuit which serves as an automatic
volume level adjuster so that you will not be deafened with sudden loud volume.
This system operates as follows. When [PWR] is switched on, the volume level is low. After that,
the volume level gradually returns to the level as the same as the one before turning off.
Anti-volume-blast circuit is not effective when volume level is lower than position 20 at the display.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
Changing Audio Modes
S
H
Press [SEL] to switch the audio modes as follows.
VOL
(Volume)
c
BAS
(Bass)
TRE
(Treble)
d
2
a
a
FAd
BAL
b
(Fader)
(Balance)
Bass and Treble
Press [SEL] to select the BASS/TREBLE mode. Press [VOL
]
j
or [VOL ] to increase or decrease the bass/treble response.
i
–12 to 0 (Center) to 12
–12 to 0 (Center) to 12
d
Balance
Press [SEL] to select the BALANCE mode. Press [VOL ] or
j
[VOL ] to shift the sound volume to the right or left speakers.
i
R or L
1 to 15
Balance Center
(R: Right, L: Left)
Fader
Press [SEL] to select the FADER mode. Press [VOL ] or
j
[VOL ] to shift the sound volume to the front or rear speakers.
i
F or R
1 to 15
Fader Center
(F: Front, R: Rear)
Note: When a control mode (BAS/TRE/BAL/FAd) is selected but no operation is made within 5
seconds (2 seconds at volume mode), the display will return to the normal operation (Radio,
Cassette, etc.) mode. In such a case, press [SEL] again to select the next control mode.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
Radio Basics
3
CQ-RG131W
Change to the tuner mode
ቢ
ባ
In case of Tape mode ..............................Eject a tape.
In case of CD Changer mode ..................Press [BAND].
CQ-W
Selecting a Band
CQ-RG1
Press [BAND] to select the band as follows.
FM1
FM2
FM3
AM
a
a
a
c
d
"ST" indicator lights if the station is broadcasting in stereo.
Manual Tuning
Press [TUNE ] or [TUNE ] to move to a higher or lower
j
i
CQ
frequency.
Hold and release
Seek Tuning
Press and hold [TUNE ] or [TUNE ] for more than 0.5 second,
j
i
CQ
then release. The radio automatically stops on the next station.
To reduce interference during
FM broadcasts (MONO)
Press [MONO] for monaural reception in case a lot of interference
is present in an FM stereo signal or to improve the listening quality
of weak FM broadcasts. To turn it off, press [MONO] again.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
Preset Station Setting
S
H
Up to 24 stations can be preset in the station memory as follows;
FM1 FM2 FM3 AM
4
6 stations 6 stations 6 stations 6 stations
Caution: For safety reasons, do not attempt to program while driving.
Manual Station Preset
CQ-RG
ቢ
ባ
Press [BAND] to select a desired band.
Use manual or seek tuning to find a station that you want to
program into memory.
ቤ
Press and hold one of the station selector buttons [1] through
[6] until the display blinks. The memory is now set for that
button on the band you have selected.
ቢ
Repeat the process to set other stations for the FM1 to AM
bands.
d
CQ
Preset Number
Note: You can change the memory setting by repeating the above
procedure.
ባ
d
Press and hold
Tuning in a Preset Station
31
Press any of the buttons [1] through [6] to tune in the station
ቢ
ቤ
preset by the above steps
to
.
ቤ
Press and hold
Auto Preset Memory
CQ-RG1
Select a band, and press and hold [BAND] (APM) for more than 2
seconds.
●
The 6 strongest available stations will be automatically set in
memory on preset buttons [1] through [6].
Once set, the preset stations are sequentially scanned for 5
●
seconds.
●
Press the appropriate preset button for the station you want to
31W
hear.
Note: The stations manually preset on the selected band will be
deleted.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
Cassette Tape Player Basics
5
CQ-RG131W
Loading a Cassette
Gently insert a cassette with the exposed tape side facing to the
CQ-RG131W
right until the mechanism captures it, and playback starts.
Program Indicator
(This indication “ ” rotates.)
Exposed Tape
Rewind and Fast Forward
When the program indicator “ ” lights, press [
] to rewind or
̆
̇̇
press [
̈̈
] to fast forward the tape.
When the program indicator “ ” lights, press [
] to fast forward
̄
̇̇
or press [
̈̈
] to rewind the tape.
“
̆
“
̄
” lights : Rewind
” lights : Fast Forword
To stop rewind or fast forward, gently press the button that is not in
use.
The tape will resume playing from that position.
“
̆
“
̄
” lights : Fast Forword
” lights : Rewind
Changing Sides
] at the same time to switch to the program
̈̈
Press [
on the other side of the tape.
] and [
̇̇
The display changes to indicate which program is playing.
Press Both at the
same time
Top Side Playing
Bottom Side Playing
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
Stopping and Ejecting the Tape
S
H
Once inserted into the unit, your tape will play continuously until
you eject it.
CQ-1W
6
If you press [ ] (EJECT), the unit ejects the tape and returns to
u
radio operation.
When you stop the car engine, the tape will stop but not be
ejected.
Notes:
●
You can not change to CD Changer mode or Radio mode while
tape is playing. If you want to change to CD Changer mode or
Radio mode, eject the tape.
Always remove the cassette when you stop using the cassette
●
player. This will prolong the life of your tape.
Notes on Cassette Tapes
Tape Slack:
Use a pencil or similar object to take up the slack
Pencil
as shown. If a loose tape is used, this may result
in the tape becoming tangled in the rotating
parts of the unit.
Do not touch
or pull out
the tape.
Cautions:
●
To maintain your cassette player in top condition, avoid using tapes that are longer than 90
minutes (C-90).
If you insert into the unit a cassette with a loose tape caused by forcing it into cassette with a
finger or the like, the cassette may not be properly reproduced. In such a case, eject the
cassette, make the tape tight, then insert it back into the deck.
●
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
CD Changer Basics
Note:
CD changer functions are applicable to units with optional CD changer unit.
(sold separately)
7
CQ-RG131W
To Changer mode
While a disc magazine is inserted in the CD changer, press
[CD·C].
Play starts from the first track.
Track Number
Play
Time
Disc Number
Note: The cassette, if loaded, should be removed. Otherwise,
the CD play will not start.
CQ-RG131W
Selecting a Disc
Press [1] ( DISC) or [2] (DISC ) to select discs in ascending
i
j
or descending order.
Selecting a Track
CQ
Press [TRACK
̈̈
] once to go to the next track. Press repeatedly
to step forward through all the tracks.
Press [TRACK ] once to play from the beginning of the current
̇̇
track. Press twice to play the previous track. Press repeatedly to
step backward through all the tracks.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
Hold and release
Searching a Track
S
H
CQ
Press and hold [TRACK
] or [TRACK
] for more than 0.5
̇̇
̈̈
second to activate fast forward or reverse through a track. Release
[TRACK ] or [TRACK ] to resume the normal CD play from
8
̈̈ ̇̇
that position.
31W
Repeating a Track
●
Press [4] (REPEAT) to repeat the current selection. “REPEAT”
indicator lights.
●
The current selection continues to repeat until you press [4]
(REPEAT) again.
Random Selection
●
Press [5] (RANDOM) to random selection of music is played
from all available CDs. “RANDOM” indicator lights.
●
To turn it off, press [5] (RANDOM) again.
31W
Scanning Tracks
●
Press [3] (SCAN). The track number blinks and the first 10
seconds of each track on the discs play in sequence.
To stop scanning and continue with the current track, press [3]
●
(SCAN) again.
31W
Press and hold
Scanning Discs
Press and hold [3] (SCAN) for more than 2 seconds. The 1st track
of all the discs in the magazine is played for 10 seconds each.
Also, Disc Number blinks at the same time. To stop the current
play of the disc scanning, press and hold [3] (SCAN) for more
than 2 seconds again.
● Error Display Messages
Displays when the compact disc
stops operating for some reason.
Please contact your nearest
authorized Panasonic Service
center.
Displays when the compact disc is
dirty or upside down. Selects the
next available compact disc.
Displays when compact disc is
scratched. Selects next available
compact disc.
Displays when there is no disc in
the magazine.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
Clock Basics
(The clock system is 12-hours.)
9
CQ-RG131W
Press and hold
Initial Time Setting
ቢ
ባ
Press [DISP]. “AdJ” is displayed.
Press and hold [DISP] again for more
than 2 seconds. “12” blinks indicating
the time setting mode is activated.
ቢ
ባ
ቤ
ብ
ቦ
To set hours, press [ ] or [ ].
j
i
d
Press [DISP] again for minute setting.
CQ
To set minutes, press [ ] or [ ].
j
i
Hold [ ] or [ ]to change numbers
j
i
rapidly.
ቤ
ቦ
ቧ
When you have set the time, press
[DISP].
d
ብ
ቧ
Resetting the Time
Press and hold
When you want to reset the time, press and hold [DISP] for more
than 2 seconds to activate the time setting mode. Then, repeat
ቤ
ቧ
step
to
above.
Selecting the Clock Display
Press [DISP] for clock display.
Press [DISP] once again, the current audio display mode
resumes.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
Installation Guide
Preparation
S
H
●
Before installation, check the radio operation with antenna and speakers.
Disconnect the cable from the negative (–) battery terminal (see caution below).
Unit should be installed in a horizontal position with the front end up at a convenient angle, but not
●
●
10
more than 30°.
Caution:
For installation to cars with trip or navigational computers, all electronic memory settings
previously registered in the computer will be lost when the battery terminal is disconnected. For
this type of car, battery could not be disconnected. Therefore, extra care should be taken to
prevent short circuitting.
In-dash Installation
53 mm
Installation Opening
In-dash installation can be done if the car’s
dashboard has an opening for this unit as shown in
Fig. 1. The car’s dashboard should have a
182 mm
thickness of 4.5 mm - 6 mm in order to make the
installation of the unit.
Fig. 1
Installation Precautions
This equipment, if possible, should be installed by a professional installer.
In case of difficulty, please consult your nearest authorized Panasonic Service Center.
1. This system is to be used only in a 12-volt, DC battery system (car) with negative ground.
2. Follow the electrical connection on page 18 carefully. Failure to do so may result in damage to the
unit.
3. Connect the power lead after other connections are made.
4. Be sure to connect the YELLOW lead to the positive terminal (+) of the battery or fuse block (BAT)
terminal.
5. Insulate all exposed wires to prevent short circuitting.
6. Secure all loose wires after installing the unit.
7. Please carefully read the operating and installation instructions of the respective equipment
before connecting it to this unit.
Supplied Hardwares
No.
Item
Diagram Qty
No.
Item
Diagram Qty
ቢ
ቦ
φ
Mounting Collar
1
Mounting Bolt (5 mm )
1
ባ
ቤ
ብ
φ
ቧ
ቨ
ቩ
Hex. Nut (5 mm )
1
1
1
Power Connector
1
1
1
Rear Support Strap
Tapping Screw
Dismounting Plate
Removable Face
Plate Case
φ
(5 mm x 16 mm)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
Installation Guide (continued)
Installation Procedures
S
H
Note: Disconnect the cable from the negative (–) battery terminal.
ቢ
1. Secure the Mounting Collar
.
11
ቢ
Insert Mounting Collar
into the
Mounting Tab
car’s dashboard, and bend mounting
tabs out with a screwdriver.
Dashboard
ቢ
Mounting Collar
Screwdriver
2. Secure the rear of the unit.
a) Check the electrical connection by referring to this operating instructions.
ቦ
b) Connect the Mounting Bolt
using a suitable wrench.
to the unit.
ቧ
c) Insert the Power Connector
ቧ
Power Connector
Unit
ቦ
Mounting Bolt
Unit
ቢ
d) Insert the unit into Mounting Collar
and push it in until “click” is heard.
e) Secure the rear of the unit to the car by either of the two recommended methods as follows.
ቤ
●
●
Using the Rear Support Strap
ቤ
Affix one end of the Rear Support Strap
Wall of Car, or some other metallic area.
to the rear of the unit, and the other end to the Fire
Using the Rubber Cushion (Option)
(If there is an existing Rear Support Bracket on the Fire Wall of Car.)
Cover Mounting Bolt on the rear of the unit with Rubber Cushion (Option), and mount it into
the existing Rear Support Bracket.
Rear Support Bracket
(existing on the car)
Fire Wall of Car
φ
3 mm
Rubber Cushion
(Option)
ብ
Tapping Screw
ባ
Hex. Nut
ቤ
Rear Support Strap
ቦ
Mounting Bolt
ቦ
Mounting Bolt
ቢ
Mounting Collar
ቢ
Mounting Collar
3. After installation reconnect the negative (–) battery terminal.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
To Remove the Unit
a) Remove the trim plate with a screwdriver as shown in the figure (Fig. 1).
12
Trim Plate
Screwdriver
PR
G
ᕡ
Fig. 1
ᕢ
ቨ
b) Pull out the unit while pushing the two lock levers using Dismounting Plate
(Fig 2, 3)
as follows.
c) Remove the unit pulling with both hands. (Fig 4).
Lock Lever
G
a
Fig. 2
ቨ
Dismounting Plate
Fig. 3
Fig. 4
a
Note: Do not lose the Dismounting Plate. It will be needed to remove the unit from the car’s
dashboard.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
Anti-Theft System
This unit is equipped with a removable face plate. By removing this face plate, the radio becomes
totally inoperable. The security indicator will blink.
13
To Remove the Removable Face Plate
a) Switch off the power.
b) Press the release button (
) (Fig. 5).
The removable face plate will be released.
Press
G
R
P
Fig. 5
c) Remove the removable face plate by pulling on
the right side of the unit. Place the removable
face plate in a supplied case.
Contacts
Main Unit
Fig. 6
Security Indicator
d) As shown in Fig.7, insert the removable face plate with the arrow pointing toward the removable
face plate case until you hear a “click”. Keep the removable face plate in the case. Then, you can
bring the plate safely.
ቩ
Removable Face Plate Case
Set two arrows together.
Fig. 7
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
To install the Removable Face Plate
a) Slide the left side of the removable face plate in place.
b) Press the right end of removable face plate until “click” is heard.
14
G
PR
PRG
Plastic Tab
Removable
Face Plate
Fig. 9
Fig. 8
Cutout
Cautions:
1. Before removing the removable face plate, make sure the power is off.
2. This removable face plate is not water-proof. Do not expose it to water or excessive moisture.
3. Do not remove the removable face plate while driving your car.
4. Do not place the removable face plate on the dashboard or nearby areas where the
temperature rises to high levels.
5. Do not touch the contacts on the removable face plate or on the main unit, since this may
result in poor electrical contacts.
6. If dirt or other foreign substances get on the contacts, wipe them with a clean, dry cloth.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
Electrical Connection
●
This unit can be connected to an optional CD changer (CX-DP88N). For details consult your
nearest Panasonic Service center.
●
For connection to a CD changer, refer to the operating instructions of the CD Changer (CX-
DP88N).
15
Cautions:
●
To prevent damage to the unit, be sure to follow the connection diagram below.
Remove the covering of the leads about 5 mm long from their end before connecting.
Do not insert the power connector into the unit until the wiring is completed.
Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle
●
●
●
all cables and keep cable terminals free from touching any metal parts.
CX-DP88N
(Option)
Extension Cord
(DIN/BATT/RCA/GND)
(Option)
Ground Lead
(To a clean, bare metallic
part of your car)
Fuse (3A)
(Yellow)
BATTERY
Battery Lead
CD Changer
Control Connector
DIN Cord
(L)
(White)
RCA Cord
(R)
(Red)
Preamp Out Connector
CQ-RG131W
L(White)
R(Red)
Power Connector
BATTERY LEAD (To Battery of Car)
Connect to the “BAT” terminal on the
fuse block of the car.
CD • Changer
Input. connector
Antenna
The power should be supplied continu-
ously to the yellow leads regardless of
the on/off position of the ignition key.
(Yellow)
Fuse(12 A)
POWER LEAD
(Red)
Connect to the “radio” power line of the
car or to the “IGN” or “ACC” terminal of
the fuse block.
Speaker Lead
Resistor (1 kΩ)
(Black)
(Blue)
GROUND LEAD
Connect to a well grounded metallic
part of your car.
(Gray w/Black Stripe)
(Violet w/Black Stripe)
(White w/Black
Stripe)
(White)
(Gray)
(Green)
MOTOR ANTENNA RELAY
CONTROL LEAD
(Green w/Black
Stripe)
(Violet)
(To Motor Antenna) (Max. 500 mA)
This lead is not intended for use with
switch actuated power antenna.
(–) (+)
(–) (+)
(–) (+)
(–) (+)
AMP·RELAY CONTROL POWER
LEAD
This lead is for connection to
Panasonic power amplifier.
(
)
Left
Speaker Speaker
(Front ) (Front )
Right
Left
Speaker
(Rear)
Right
Speaker
(Rear)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
Speaker Connections
Cautions:
1. Use ungrounded speakers only.
2. The speakers to be used with this unit should be able to handle more than 40 W of audio
power. If an optional amplifier is used, the speakers should be able to handle the maximum
output power of the amplifier. Use of speakers with small input ratings can cause damage to
the speakers.
16
3. The speaker impedance should be 4 - 8 ohms. If the impedance is too large or too small, it
affects the output and may cause damage to the speakers or this unit.
4. Do not use 3-wire type speaker system having a common earth lead. Never connect the
speaker cord to the body of the car. This unit uses the BTCL circuit, so each speaker should
be connected separately using parallel vinyl insulated cords.
5. The speaker cords and the power amplifier unit should be kept away (about 30 cm apart) from
the antenna and antenna extension cord.
6. Follow the connection diagram below carefully. Failure to do so may cause damage to both unit
and speakers.
●
Unit will be damaged if speakers (Front, Rear) are not connected properly.
(White)
+
_
+
_
+
_
+
_
+
_
+
_
L
L
L
(White
w/Black Stripe)
WRONG
WRONG
RIGHT
Chassis
Chassis
(Gray)
+
_
+
_
+
_
+
_
+
_
+
_
R
R
R
(Gray
w/Black Stripe)
●
Do not connect more than one speaker to one set of speaker leads.
(White)
+
_
+
_
+
_
+
_
+
_
L
L
(White
w/Black Stripe)
RIGHT
WRONG
(Gray)
+
_
+
_
+
_
+
_
+
_
R
R
(Gray
w/Black Stripe)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
Troubleshooting
●●Troubleshooting Tips
17
PROBLEM
POSSIBLE CAUSE
PROBABLE SOLUTION
Unit will not turn on.
Dead vehicle battery.
Ignition not on.
Charge vehicle battery.
Turn ignition to On or Accessory.
Bad power line connection.
Fuse burned out.
Check connections.
Replace fuse.
Radio has static.
Antenna not hooked up.
Hook up antenna.
Close to high power lines.
Move away from high power lines.
Radio memory buttons do Not holding buttons down Press and hold buttons for more
not work.
long enough.
than 2 seconds.
Tape sound quality is poor.
Heads are dirty.
Clean heads. (Ask
a
service
representative for advice.)
Use better quality tape.
Poor quality tape.
Tape will not change
programs.
Not pressing [
buttons at the same time.
] and [
] Press [
̈̈
] and [
same time.
] buttons at the
̇̇
̈̈
̇̇
CD Changer will not operate. Unit not properly connected. Check connections.
•
Unit not switched into CD Press [CD C].
Changer mode.
No CDs in the magazine.
Check disc magazine.
CD Changer will not play a Disc loaded upside down.
Reload disc properly.
specific disc.
Disc damaged.
Check disc for scratches, chips.
Disc not loaded in magazine. Check disc magazine.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
E
N
G
L
I
S
H
Fuse
Be sure to use a fuse of the specified rating (12 A) when replacing a blown fuse. Fuses with higher
capacity ratings, use of any substitute, or connection without a fuse may result in a fire hazard or
damage to the unit. If the replacement fuse fails, consult your nearest authorized Panasonic Service
Center.
18
Maintenance
To clean the exterior of this unit, use a soft cloth to wipe the surface. Do not use benzine, thinner or
any other type of solvents.
Specifications
General
Power Supply
Tone Controls
: DC 12 V (11 V - 16 V), Test Voltage 14.4 V, Negative Ground
: Bass; ±12 dB at 100 Hz
Treble; ±12 dB at 10 kHz
Current Consumption
Maximum Power Output
Power Output
Speaker Impedance
Dimensions (Main unit)
Weight (Main unit)
: Less than 2.5 A (Tape mode, 0.5 W 4-Speaker)
: 40 W x 4 (at 4 Ω)
: 20 W x 4 (DIN45 324, at 4 Ω)
: 4 Ω (4 - 8 Ω acceptable)
: 178(W) x 50(H) x 150(D) mm
: 1.6 k
g
FM Stereo Radio
Frequency Range
Usable Sensitivity
Stereo Separation
: 87.5 - 108 MHz
: 6 dB/µV (S/N 30 dB)
: 35 dB (at 1 kHz)
AM Radio
Frequency Range
Usable Sensitivity
: 531 - 1602 kHz
: 28 dB/µV (S/N 20 dB)
Cassette Player
Reproduction System
Tape Speed
FF/REW Time
Frequency Response
Wow and Flutter
Signal to Noise Ratio
: 4-track, 2-program stereo
: 4.76 cm/sec.
: Less than 200 sec. (C-60)
: 35 - 14000 Hz
: 0.12 % (WRMS)
: 52 dB
Note: Specifications and the design are subject to possible modification without notice due to
improvements.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
CQ-RG131W
1
[PWR]
●
●
[VOL
]
[VOL
]
i
j
0
39
]
i
[VOL
]
[VOL
j
CQ-RG131W
●
●
[MUTE]
MUTE
●
●
[MUTE]
CQ-RG131W
[MUTE](LOUD)
2
●
[MUTE](LOUD)
2
20
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
[SEL]
VOL
BAS
TRE
BAL
FAd
2
[SEL]
[VOL
[VOL
]
j
]
i
–12
0
12
–12
0
12
d
[SEL]
BALANCE
[VOL
]
j
[VOL
]
i
R
L
1
15
R:
, L:
●
[SEL]
FADER
[VOL
]
j
[VOL
]
i
F
R
1
15
F:
, R:
[
BAS/
TRE/
BAL/
FAd]
5
VOL
2
SEL
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
CQ-RG131W
3
ቢ
ባ
..................................
........................
CD
BAND
CQ-W
CQ-RG1
[BAND]
FM1
c
FM2
ST
FM3
AM
d
a
a
a
CQ
[TUNE
]
[TUNE
]
j
i
CQ
[TUNE
]
[TUNE
]
i
j
MONO
[MONO]
[MONO]
24
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
24
6
FM1
FM2
FM3
AM
6
6
6
4
CQ-RG
ቢ
[BAND] (
)
ባ
ቤ
[1] [6]
FM1 AM
ቢ
d
d
CQ
ባ
31
ቢ
ቤ
[1] [6]
ቤ
CQ-RG1
[BAND] APM
2
●
●
●
[1] [6]
6
5
31W
25
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
CQ-RG131W
5
CQ-RG131W
“̆”
[̇̇]
[̇̇ ]
[̈̈]
“̄”
[̈̈ ]
̆
̄
̄
̆
[̇̇ ] [̈̈ ]
26
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
CQ-1W
[
]
EJECT
u
●
●
CD
6
CD
●
●
90
(C-90).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
(
CQ-RG131W
7
[CD·C]
CQ-RG131W
[1] ( DISC) [2] (DISC
)
j
i
CQ
[TRACK̈̈ ]
[TRACK̇̇ ]
28
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
CQ
[TRACK̈̈] [TRACK̇̇]0.5
[TRACK̈̈ ]
[TRACK̇̇]
31W
●
●
[4] REPEAT
REPEAT
8
[4] REPEAT
●
●
[5] RANAOM
CD
[5] RANAOM
31W
●
●
[3] SCAN
10
[3] SCAN
31W
[3] SCAN
2
10
[3]
SCAN
2
●
CD
CD
Panasonic
29
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
12
CQ-RG131W
9
ቢ
ባ
AdJ
2
ቢ
ባ
12
d
d
ቤ
ብ
ቦ
[
[
]
]
[
[
]
]
j
i
CQ
j
i
ቤ
ቦ
[
]
[
]
i
j
ቧ
[DISP]
ብ
ቧ
[DISP]
2
ቤ
ቧ
[DISP]
[DISP]
30
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
●
●
●
−
( )
30
10
53 mm
1
182 mm
1
4.5 mm - 6 mm
Panasonic
(+)
1.
2.
3.
4.
5.
6.
7.
12
36
(BAT)
ቢ
ቦ
φ
1
1
1
1
(5 mm )
1
1
1
1
ባ
ቤ
ብ
φ
ቧ
ቨ
ቩ
(5 mm )
φ
(5 mm x 16 mm)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
(
)
(–)
ቢ
1.
2.
ቢ
ቢ
11
a)
b)
c)
ቦ
ቧ
ቧ
ቦ
ቢ
d)
e)
ቤ
●
●
ቤ
ቦ
φ
3 mm
ብ
ባ
ቤ
ቦ
ቦ
ቢ
ቢ
−
( )
3.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
a)
1
PR
G
ᕡ
1
12
ᕢ
ቨ
b)
c)
2, 3
4
G
a
2
3
ቨ
4
a
33
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
a)
b)
(
)
5
G
R
P
13
5
c)
6
d)
7
ቩ
7
34
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
a)
b)
G
PR
PRG
14
9
8
1.
2.
3.
4.
5.
6.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
●
●
(CX-DP88N)
(CX-DP88N)
Panasonic
●
●
●
5 mm
(
)
●
15
CX-DP88N
BATTERY
CQ-RG131W
(–) (+)
(–) (+)
(–) (+)
(–) (+)
(
)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
1.
2.
40 W
3.
4
8
4. BTCL
5.
6.
(
30 cm
16
●
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
●
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
37
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
●●
ON ACC
17
2
[̈̈] [̇̇]
[̈̈] [̇̇ ]
CD
CD
•
CD
CD
[CD C]
CD
CD
CD
CD
CD
CD
CD
CD
38
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
(12 A)
Panasonic
18
DC 12 V (11 V - 16 V
14.4 V
; 100 Hz
; 10 kHz
12 dB
12 dB
2.5 A (
0.5 W 4
)
40 W 4 (4
20 W 4 (4
)
DIN45 324 4
)
4
(4 - 8
178 (
1.6
)
50 (
)
150 ( ) mm
87.5 - 108 MHz
6 dB/ V (S/N 30 dB
35 dB (1 kHz
531 - 1602 kHz
28 dB/ V (S/N 20 dB)
4
2
4.76 cm/sec
200 (C-60)
35 - 14000 Hz (
/
)
0.12
(WRMS)
52 dB
39
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-RG131W
Matsushita Electric Industrial Co., Ltd.
Central P.O. Box 288, Osaka 542-8588, Japan
YFM284C346CC TAMACO0102-0 Printed in Taiwan
Download from Www.Somanuals.com. All Manuals Search And Download.
|