This product complies with the RoHS Directive (EU 2002/95/EC).
Zener Diodes
MAYS0750Y
Silicon epitaxial planar type
For ESD protection of high speed signal line
Unit: mm
+0.05
–0.03
0.60
+0.05
+0.05
–0.03
Features
0.12
0.80
–0.02
Maintain signal cobs with low insertion loss, distortion.
1
0.01 0.01
Absolute Maximum Ratings Ta = 25°C
Parameter
Symbol
Rating
150
Unit
mW
°C
2
0.30 0.05
+0
1
0
Total power dissipation *
PT
Tj
–0.05
5°
Junction temperature
Storage temperature
150
T
stg
–55 to +150
±8
°C
2
Electrostatic discharge *
ESD
kV
Note) 1: P = 150 mW achieved with a printed circuit board.
*
T
2: Test method: IEC61000-4-2
*
1: Anode
(C = 150 pF, R = 330 W, Contact discharge: 10 times)
2: Cathode
EIAJ: SC-79
SSMini2-F1 Package
Marking Symbol: CY
Electrical Characteristics Ta = 25°C±3°C
Parameter
Breakdown voltage *
Symbol
VBR
IR
Conditions
Min
Typ
Max
Unit
V
IR = 1 mA
VR = 5 V
6.0
7.5
Reverse current
2
mA
pF
Terminal capacitance
Ct
IR = 0 V, f = 1 MHz
0.8
Note) 1. Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7031 measuring methods for diodes.
2. : V guaranted 20 ms after current flow.
*
Z
Publication date: February 2007
SKE00031AED
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
– Any applications other than the standard applications intended.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
Electric Industrial Co., Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
|