Panasonic Laptop CF 35 User Manual

Personal Computer

OPERATING INSTRUCTIONS

CF-35 Series

Contents

Getting Started

Read Me First ................................................. 5

First-time Operation ........................................ 6

Operation

Starting Up/Shutting Down.............................. 9

Computing On the Road ............................... 12

Using the Battery Pack.................................. 15

Security Measures ........................................ 17

Infrared Data Communications ..................... 21

Add-ons/Peripherals...................................... 22

Usage, Carrying and Maintenance ............... 27

Troubleshooting

Computer Diagnosis ..................................... 28

Dealing with Problems .................................. 29

Reinstalling Software .................................... 32

CF-35 Quick Guide

(On-line manual on the hard disk)

Appendix

Windows 95 Setup Procedure....................... 35

Setup Utility ................................................... 36

Specifications ................................................ 38

LIMITED USE LICENSE AGREEMENT ...... 40

Index ............................................................ 43

Click

on the screen.

-Contents-

CF-35 Readme

Key Combinations

Indicators

Download from Www.Somanuals.com. All Manuals Search And Download.

For U.K.

Lithium Battery

FORYOUR SAFETY PLEASE READTHE FOLLOWING

TEXT CAREFULLY

Lithium Battery!

This computer contains a lithium battery to enable the date, time,

and other data to be stored in it.

Should only be exchanged by service personnel.

Warning! Risk of explosion from incorrect installation or mis-

application!

This appliance is supplied with a moulded three pin mains plug

for your safety and convenience.

A 3 amp fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the re-

placement fuse has a rating of 3 amps and that it is approved by

ASTA or BSI to BS 1362.

Litium batteri!

Denna dator innehåller ett lithium batteri som avänds för att

lagra datum, tid och annan data.

Bör endast bytas av servicepersonal. Explosionsfara vid felaktig

hantering.

Check for the ASTA mark

of the fuse.

or the BSI mark

on the body

If the plug contains a removable fuse cover you must ensure that

it is refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until a re-

placement cover is obtained.

A replacement fuse cover can be purchased from your local

Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR

THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE

SHOULD BE REMOVED AND THE PLUG CUT OFF AND

DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK

IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP

SOCKET.

For U.S.A.

Federal Communications Commission Radio

Frequency Interference Statement

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more

of the following measures:

If a new plug is to be fitted please observe the wiring code as

shown below.

If in any doubt please consult a qualified electrician.

Important

The wires in this mains lead are coloured in accordance with the

following code:

Blue:

Brown:

Neutral

Live

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the Panasonic Service Center or an experienced ra-

dio/TV technician for help.

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured Blue must be connected to the ter-

minal which is marked with the letter N or coloured BLACK.

The wire which is coloured Brown must be connected to the

terminal which is marked with the letter L or coloured RED.

Under no circumstances should either of these wires be connected to

the earth terminal of the three pin plug, marked with the letter E or the

Warning

To assure continued compliance, use only shielded interface

cables when connecting to a computer or peripheral. Also, any

changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this equipment.

Earth Symbol

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesired operation.

The mains plug on this equipment must be used to disconnect

the mains power.

Please ensure that a socket outlet is available near the equip-

ment and shall be easily accessible.

How to replace the fuse

Open the fuse compartment with a

screwdriver and replace the fuse.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warnings

This equipment is not designed for connection to an IT power

Precautions

system.

Usage

(An IT system is a system having no direct connections be-

tween live parts and Earth; the exposed-conducive-parts of the

electrical installation are earthed.

An IT system is not permitted where the computer is directly

connected to public supply systems in the U.K.)

Avoid Extreme Heat and Cold

Do not store or use the computer in locations

exposed to heat, direct sunlight, or extreme cold.

Avoid moving the computer between locations

with large temperature differences.

Operation: 5 ^oC to 35 ^oC (41 ^oF to 95 ^oF)

Storage: -20 ^oC to 60 ^oC (-4 ^oF to 140 ^oF)

Disconnect the mains plug from the supply socket when the

computer is not in use.

This equipment is produced to BS800/1983.

Avoid Direct Sunlight on the LCD Panel

The LCD panel should not be exposed to direct

sunlight or ultraviolet light.

Avoid Humidity Liquids and Dust

Do not store or use the computer in locations

exposed to high humidity, liquids (including rain)

or dust.

For Germany

Warnung bezüglich der LIthiumbatterie

(Sicherungsbatterie)

Lithiumbatterie!

Dieser Computer enthält eine Lithiumbatterie zur Sicherung von

Datum und Uhrzeit der eingebauten Uhr sowie anderer

Systemdaten im Speicher bei einer Unterbrechung der

Hauptstromversorgung. Diese Sicherungsbatterie darf nur von

Kundendienstpersonal ausgewechselt werden.

Prevent Shock

Avoid subjecting the computer to severe

vibrations or impact. Do not place the computer

inside a car trunk.

Avoid Radio Frequency Interference

Do not place the computer near a television or

radio receiver.

Warnung! Bei falschem Gebrauch besteht Explosionsgefahr!

Entsorgung gebrauchter Batterien nach Angaben des Herstellers.

Handling

Avoid Magnetic Fields

Keep the computer away from magnets.

For France

Avertissement concernant la pile au lithium

(pile de sauvegarde)

Pile au lithium!

Avoid Stacking

Do not place heavy objects on top of the

computer.

Le micro-ordinateur renferme une pile au lithium qui permet de

sauvegarder certaines données comme la date et l'heure

notamment. Elle ne devra être remplacée que par un technicien

qualifié.

Keep Small Objects Away

Do not insert paper clips or other small objects

into the computer.

Avertissement! Risque d'explosion en cas de non respect de cette

mise en garde!

Do Not Disassemble the Computer

Do not attempt to disassemble your computer.

Avoid Excessive Force to the LCD Panel

Do not apply excessive downward force on the

display when it is completely opened, especially

when plugs and/or cables are connected to the

rear of the computer.

Cables

Use of an interface cable longer than 3 m (9.84 feet) is not

recommended.

Download from Www.Somanuals.com. All Manuals Search And Download.

Read Me First

Saving Data on the Hard Disk

Do not expose your computer to shock.

Please use care when handling your computer, shock may

damage your hard disk or make your software applications

and data unusable.

Do not power down your computer while software ap-

plications are running or HDD indicator ( ) is on.

Properly shut Windows* down to avoid problems ([Start]-

[Shut Down]).

Disk Utilities not conforming to FAT32 should not be

used in the computer.

Running such programs may result in the incorrect dis-

play of hard disk drive (HDD) content or damage to data

on the HDD. For more information, please read the "CF-

35 Readme" in the "CF-35 series Quick Guide" (Click

Save all valuable data to floppy disks.

Backing up data to floppy disks will limit damage should

trouble occur to your computer or should you inadvertently

change or erase data.

Use the security function for all important data.

page 17 - Security Measures

Do not add the check mark

to [DMA] in [Start] -

[Settings] - [Control Panel] - [System] - [Device Man-

ager] - [Disk drives] - [GENERIC IDE DISK TYPE**]

- [Settings].

* This computer uses Microsoft^®Windows^®95 Operating System.

It may damage to data on the hard disk.

Saving Data on Floppy Disks

Do not power down your computer or press the floppy

disk drive eject button while the FDD indicator ( ) is

on.

Doing so may damage the data on the floppy disk and render

the disk useless.

Internet Explorer 4.0

Only CF-35PJJ8C M/CF-35PJJ8C E comes with

Internet Explorer 4.0 already installed.

Use care when handling floppy disks.

To protect the data on your floppy disks or to prevent a floppy

disk from becoming stuck in your computer, avoid the fol-

lowing:

• Sliding the shutter on the floppy disk manually.

• Exposing the disk to a magnetic field.

• Storing the disk in locations prone to high temperatures, low

pitched noise, dampness, or dust.

• Applying more than one label on the disk.

Confirm the contents of a floppy disk before formatting

it.

Confirm that no important data is on the disk, because all

data on the disk will be erased.

Internet Explorer 4.0 places a tremendous load on the sys-

tem in order to execute the wide variety of functions that it

provides. As a result, some unexpected faults may occur.

If any of these faults occurs, try using the software with

some Internet Explorer 4.0 functions turned off. (See Internet

Explorer Help for more details.)

It takes a long time to reboot or the computer locks

up.

Delete the check mark

nel Bar] in [Control Panel] - [Display] - [Web], then

press

for [Internet Explorer Chan-

The software cannot be upgraded (installed).

At the [Welcome - Microsoft Internet Explorer] which

Use the write-protect tab.

This is a must for preserving important data. This prevents

your data from being erased or overwritten.

appears at startup, delete the check mark

for [Show

this next time you log in] and restart the computer.

A system module error occurs.

Write-protectTab

Set [ (None)] for [Wallpaper] in [Control Panel] -

[Display] - [Background].

Performing the above steps does not solve the prob-

lem.

Write Disable

Write Enable

Uninstall Internet Explorer 4.0 with the following step.

Select [Microsoft Internet Explorer 4.0] in [Start] - [Set-

tings] - [Control Panel] - [Add/Remove Programs] - [In-

stall/Uninstall] and press [Add/Remove]. Follow the on-

screen instructions.

Computer Viruses

Users are advised to purchase the latest versions of vi-

rus protection software and use them regularly.

We recommend you run the software:

If a window with the message [Version Conflict] ap-

pears during the installation process (network card

• When booting your computer.

• After receiving data.

and application installation), select

We recommend that you check data received on floppy

disks or from external sources, such as data downloaded

from the Internet, e-mail, etc. (For compressed files, please

uncompress them before running a check).

Proper operation may not be possible if

lected.

is se-

Download from Www.Somanuals.com. All Manuals Search And Download.

First-time Operation

It’s now time to get started. Please read the steps below to help you learn what parts are in-

cluded, and to gain an understanding of some basic computer-related operations.

Confirm the inclusion of all parts

Make sure the parts shown in the figure have been supplied. If any of them is missing

or is not working properly, please consult your nearest Panasonic dealer.

CAUTION

Please prepare 8 2HD formatted floppy disks to create backup disks of the Panasonic

and the other utilities ( page 8; step 6). These backup disks are to be used when

reinstallation of the Panasonic and the other utilities becomes necessary.

AC Cord ................................. 1

AC Adapter ............................ 1

CF-AA1526

Operating Instructions ......... 1

Dummy FDD ..........................1

For use in place of your floppy drive

(

page 22)

TranXit ................................... 1

Windows 95 System Pack .... 1

(Microsoft Corporation)

First-step Guide

CD-ROM

Registration Card

Accessory Catalogue

CF-35PJJ8C M/CF-35PJJ8C E... 2 discs

For all other models .................. 1 disc

Download from Www.Somanuals.com. All Manuals Search And Download.

Connect your computer to a power outlet

CAUTION

Handling the AC adapter

Do not twist or pull the AC power cord forcefully. Doing so may damage the

connections.

Use only the specified AC adapter (factory control number: CF-AA1526) with

your computer. Using an AC adapter other than the one supplied might damage

the battery and/or the computer.

When the DC plug is not connected to the computer, disconnect the AC cord

from your AC wall outlet as well. If the cord is kept connected, a very low level

of power equivalent to approximately 1.1 watts^*will be consumed.

^*When the battery pack is not recharging or fully charged

Problems such as sudden voltage drops/surges may arise during periods of thun-

der and lightning. Since this could adversely affect your computer, the

uninterruptible power source (UPS) is highly recommended.

Please make sure that the ferrite core is always attached to the plug of the AC

adapter and in its proper position.

Clamps

The ferrite core can be removed

by unlatching the clamps with a

pair of mini-pliers, etc.

When reattaching the ferrite

core, match the end of the ferrite

core to the third groove from the

bottom of the plug (see diagram)

before closing it.

Read the LIMITED USE LICENCE AGREEMENT ( page 34)

To open the display, slide the latch located at the front and lift open the display. Before

removing the seal covering the power switch, please read the LIMITED USE LICENSE

AGREEMENT. Removal of this seal indicates agreement to the terms specified. After

you have agreed to the terms, you may turn your computer on.

CAUTION

Do not slide the power switch repeatedly.

After you have turned your computer off, you must wait ten seconds before you

can turn it back on.

Move the power switch

toward the rear direction

and hold one second un-

til the power indicator

Latch

(

) goes on before re-

leasing it.

Download from Www.Somanuals.com. All Manuals Search And Download.

First-time Operation

4 _{SetWindows up}

The [Windows 95 Setup] will run after the computer is turned on. Simply follow the on-

screen instructions.

NOTE

Please read the supplemental “Windows 95 Setup Procedure” for a more detailed

explanation ( page 35).

Moving the cursor ( ) or clicking buttons can be done through the touch pad

(

page 10).

If the display is dim or the sound quality is not right, you can adjust the brightness or

contrast (for DSTN display models only) and volume ( page 39).

CF-35PJJ8C M/CF-35PJJ8C Eonly

(For all other models, go to Step 6)

Close Internet Explorer 4.0

At the [Welcome - Microsoft Internet Explorer], select

close the screen.

at the upper right portion to

Double-click

(Panasonic Setup icon) on Windows

Inserting a floppy disk

(To create the backup disks and setup the factory-set)

Eight 2HD formatted floppy disks need to be prepared. Simply follow the on-screen in-

structions. The eight disks will contain the following (the check boxes are for you to

confirm copy of the disks).

Label-side up

Label on the top surface, and

inserting the shutter-side

headfirst.

Firstaid FD..................................................... 1 disk

PanasonicTools Disk ................................... 1 disk

TranXit Disk (1, 2).......................................... 2 disks

Drivers Disk (1, 2) .........................................2 disks

PhoenixCard Manager^TM95 Disk (1, 2) ........2 disks

Ejecting a floppy disk

CAUTION

Restarting the system may take some time.

Eject Button

Please store the backup disks in a safe place. They will enable you to return your

computer to factory default settings should any problems occur.

Do not remove the floppy disk while the FDD indicator ( ) is on, power down

your computer or use the suspend function (

page 10).

NOTE

About the CF-35 series Quick Guide

This is available as an on-line guide which includes information on the key input com-

mands, LED indicators and the “CF-35 Readme”. The “CF-35 Readme” also contains

detailed information.

For the Quick Guide, we recommend setting the Desktop area to "800 by 600 pixels" or

more, and the Color palette to "High Color (16 bits)" or more.

About Internet Explorer 4.0

Please select the item that you want to open from the menu on the [Welcome - Microsoft

Internet Explorer].

CF-35PJJ8C M/CF-35PJJ8C E only

This concludes the first-time use operation guidelines.

Download from Www.Somanuals.com. All Manuals Search And Download.

Starting Up/Shutting Down

Starting Up

Open up the display

Slide the latch as shown and lift open the display.

NOTE

Do not turn on the computer with the LCD panel closed if an external monitor is not

connected. The computer will not power on.

Latch

Turn your computer on

Move the power switch toward the rear direction and hold one second until the power

indicator ( ) goes on before releasing it.

CAUTION

Do not slide the power switch repeatedly.

After you have turned your computer off, you must wait ten seconds before you

can turn it back on.

If the computer does not turn on when the power is switched on, the temperature of

the CPU has exceeded its normal operating temperature. In this case, a function

designed to prevent it from overheating is triggered automatically and prevents the

computer from turning on. Should this happen, allow the computer to cool down

then switch the power on again.

If the computer still does not turn on, please consult your nearest Panasonic dealer.

is displayed,

you must first enter your User Password ( page 17).

Upon entering your

User Password and

pressing

If the correct password is input,

Over three incorrect attempts,

Will Start

Will Not Start*

(Power off)

* If you are starting from the suspend mode (

page 10), if

after three attempts the correct password is not input, or if no

password is entered for about a minute, the computer returns

to the suspend mode.

NOTE

If the display on the right appears,

the network password has been set.

To read and write data to other

computers, the correct password

must be entered.

When an application or file that was previously displayed ap-

pears on your screen,

this means the suspend or hibernation mode ( page 10) has been set.

Select your application

You are able to start working on your computer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Starting Up/Shutting Down

Using the Touch Pad

Use the touch pad to move the cursor on the display and perform normal computer operations. It

is not necessary to apply too much pressure on the work surface.

Moving the cursor

CAUTION

Leaving your finger on the touch pad for more than 15 seconds will put your computer in

the Calibration mode. In this mode, there are instances where even if you slide your

finger on the work surface, the cursor will not move. In such cases, you have to lift your

finger from the work surface and apply your finger to the work surface again.

When using drawing applications like Paint, please try to draw in the center of the

work surface. There are cases where lines drawn later appear to have been drawn

incorrectly.

Work Surface

Cursor

Double-clicking

Dragging

Clicking

While holding

down the button,

moving your fin-

ger on the work

surface

One tap

Two quick

taps

Two quick

taps

Two quick taps,but on

the second tap leav-

ing your finger down

(applying pressure)

and moving it on the

work surface. One tap

when your finger will

“drop”the object.

NOTE

To change the touch pad settings, select [Mouse] in [Start] - [Settings] - [Control

Panel]. Even if [Left-handed] is selected in the mouse settings, tapping the touch

pad will have the same effect as clicking the left button of the touch pad.

Shutting Down (power off your computer)

To shut down, save all data and select [Shut Down] from the

[Start] menu

NOTE

From the keyboard,

you may choose to press down on

then select [Shut Down].

2 _{Confirm shutdown}

Select [Shut down] (or [Shut down the computer?]), then press

Your computer will power off automatically.

(or

(In the OFF state, if you are not recharging your battery pack or if the pack is fully charged, your computer and

the AC adapter consume approximately 1.1W.)

(The display varies depending on the

models.)

Restarting your computer (without shutting down)

Select [Restart] (or [Restart the computer?]), then press

(or

NOTE

To quickly resume computer operation after shutting down,

the suspend and hibernation functions are available. ( below)

Starting Up Your Computer Quickly

If you want to immediately start up and continue an application after shutting down your com-

puter, you can do so by using the suspend or hibernation function.

Differences between suspend function and hibernation function

Function

Where data is saved to

Speed

Requires power supply

Suspend function

Hibernation function

Memory

Hard disk

Fast

Somewhat slow

Yes (if power is cut, all data is lost)

Power not required to maintain data

Download from Www.Somanuals.com. All Manuals Search And Download.

Shutting Down

Using the suspend function

NOTE

You can use the suspend function by selecting [Suspend]^*from [Start] menu.

[Suspend] is deleted from the [Start] menu by unchecking [Allow Windows to manage power use on

Suspend Mode

Power Switch

this computer.] in [Start] - [Settings] - [Control Panel] - [Power] or by unchecking [Show suspend

command on Start menu] in [Advanced].

Using the hibernation function

It is necessary to set the hibernation function using the Setup Utility.

Run the Setup Utility ( page 36)

Using

and

, select [Power Management] then press

Do not touch the

power switch while

your computer is en-

tering the hiberna-

tion mode.

Using

with

and

, then press

, select [Power Switch], set [Hibernation]

Close the Setup Utility ( page 36)

Hibernation Mode

CAUTION

Save all data before powering off your computer.

When restarting from or shutting down to the suspend or hibernation mode, do not

touch the touch pad (or move the mouse (serial or PS/2 type) if one is connected).

There are cases where these devices will fail to operate; you will have to restart

your computer using the keyboard ( page 10).

Do not power off during the following periods (you may corrupt your data or file):

• While the FDD indicator ( ), HDD indicator ( ) or CD-ROM indicator (

)

(CD-ROM drive is an optional part) is on.

• While playing/recording audio files.

• While communications software is being used.

Do not use the suspend or hibernation function when using an OS other than Win-

dows 95, the diagnostics program (DIAG35), or the Setup Utility, or when experi-

encing static electricity or noise.

If you hold down on the

to enter the suspend or hibernation

mode, after resuming operation, you must press the same key. For example, if you

hold down on the

do not press the

key while sliding the power switch, upon resuming, if you

key again, only capital letters will result from typing.

If your computer locks up, press the reset button. All data is lost when this button

is pressed.

In the suspend mode, power is consumed. If PC cards (e.g., modem card) are

inserted, more of that power is consumed. When all power has been consumed, all

data at shutdown is lost since it is retained in memory. We therefore recommend

plugging in the AC adapter when using the suspend function.

When the file in the external devices such as a CD-ROM drive, external hard disk,

or ATA cards is opened, the suspend or hibernation function may not work. In such

cases, close the file.

SCSI cards may not recover operation after entering the suspend or hibernation

mode. If this occurs, restart the computer.

Resuming Operation

Power Switch

is displayed upon sliding the power switch, your password has been set ( page 9).

CAUTION

When operation resumes, serial devices such as a mouse or modem, or your PC Cards

may not work. In such cases, you will need to restart your computer or reinitialize the

individual devices.

Download from Www.Somanuals.com. All Manuals Search And Download.

Computing On the Road

One of the main features of notebook-type computers is that you have the power of computing

away from your home or office. In the following, information is provided on how to maximize

use of the battery pack which is necessary for such computing.

Four Important Points

POINT 1

Be sure to charge your battery before and after use.

POINT 2

To get the maximum use of your battery, set the power

management mode.

POINT 3

Check to see that you have your AC adapter with you before

leaving your home or office.

Purchasing an extra battery (CF-VZS351) or the optional battery charger

(CF-VCB251A) is highly recommended.

POINT 4

Always watch your battery level!

Conserving Power

Things to Remember

Leave your computer off when it is not in use ( page 10)

Adjust the brightness (dark) with

(

page 39)

Before stepping away from your computer, press

put your computer in the standby mode

The standby mode helps you conserve power by cutting off power to the hard disk

drive’s motor and LCD. To resume, you may press any key.

In the power management mode, the setting of [Advanced] is

recommended ( page 13)

With the Setup Utility, you can set the [Advanced] mode. This mode allows you to

maximize power save regardless of whether you are using only the battery pack or the

AC adapter.

Setting the hibernation timeout ( page 13)

The hibernation function ( page 10) allows you to save power by automatically cut-

ting off power when the computer is idle or there is no access to individual devices for 4

or 16 minutes. If [Advanced] or [Standard (Battery/AC adapter)] is selected for [Power

Saving], the hibernation timeout function will go into effect for both the battery pack

and the AC adapter. If, however, [Standard (Battery)] or [OFF] is selected for [Power

Saving], it will go into effect only during operation by the battery. The standby timeout

function is automatically set when [Advanced] or [Standard] is set. Note that the standby

timeout precedes the hibernation timeout.

It should be noted that for some applications, the hibernation timeout will not work

properly.

NOTE

If you plan to use only the battery pack or set the power management, it is necessary to

check

[Allow Windows to manage power use on this computer] in [Start] - [Set-

tings] - [Control Panel] - [Power]. If no check is added, the hibernation timeout will

not occur.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Power Management

(How to set [Advanced] and the hibernation timeout)

Run the Setup Utility ( page 36)

Using

and

, select [Power Management] then press

, select [Power Saving] then set [Advanced]

Using

with

(To avoid setting the hibernation timeout, press

and proceed on to step 6.)

Using

and

, select [Power Switch] then set [Hiberna-

tion] with

Using

and

, select [HibernationTimeout], set either [4

min] or [16 min] with

then press

Close the Setup Utility ( page 36)

NOTE

If you would like to temporarily disable your power management settings, press

. When pressed again, or when the computer is restarted (including suspend or

hibernation function), the settings are enabled.

Power Management settings

Functions automatically

CPU Speed

Change Mode

Enable

HDD Motor

Timeout

1 min

Standby

Timeout

1 min

Power

Management

set

Advanced

Standard (Battery/AC adapter)

Standard (Battery)*

OFF

Enable

Disable

1 min

Never

2 min

Never

^*Enabled only when the battery itself is being used.

CPU Speed Change Mode

HDD Motor Timeout

Standby Timeout

In this mode, the CPU is automatically stopped when there

are no operations.

When the hard disk drive is not accessed for more than a

minute, power to the motor is shut off.

When the computer is idle or a device is not accessed for

one or two minutes, the computer enters the standby mode

(

page 12).

CAUTION

When you need a network environment.

Be sure to disable hibernation timeout settings in the Setup Utility .

After resuming operation from the hibernation mode, the network connection may be severed or the

computer will not work properly.

In communications when a device like a high-speed modem or ISDN terminal adapter

is connected to the serial port, etc.

There are times when high-speed communication is adversely affected if the power management

function is enable. Please confirm that

is displayed for a few seconds by pressing

disable the power management function. After you have finished using a communication device, you

can enable the power management function by pressing

Key operation and music playback

When the power saving function is running, the keyboard and mouse operations may feel sluggish.

Also, music may not play correctly when entering the standby mode during operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Computing On the Road

Battery Status

Use the Battery Indicator ( ) to Check on the Battery Status

Battery Indicator

Battery Status

Charging

Fully-charged

Orange*

Green*

Battery charge is low (the charge is less than approx. 9% capacity)

Battery pack or charger may not be working properly.

Check your connections. If the problem persists, consult your

nearest Panasonic dealer.

Red

Blinking red*

Unable to recharge due to violation of temperature limits

Blinking orange for 5

seconds after the AC

adapter is connected*

(

page 15)

* When the AC adapter is connected.

NOTE

When using the optional CD-ROM pack:

Recharging is temporarily stopped when the drive is being accessed. In this case,

the battery indicator goes off temporarily.

In addition, recharging is temporarily discontinued when the CD-ROM AutoPlay

function is enabled. For more information, please read the operating instructions

that are supplied with the CD-ROM pack.

Getting a detailed reading

NOTE

When the battery indicator remains red (or a 99% reading is displayed) for an

extended period of time, the actual remaining battery level and the displayed

level may differ. Should this occur, charge the battery until the indicator is green,

then completely discharge the battery.

When the battery pack is not in the computer,

is displayed.

When the Remaining Battery Charge Becomes Low

save your data and power off your computer

Perform the following:

Plug in the AC adapter, and fully charge your battery.

Use a spare battery if you have one.

If you have neither the AC adapter nor an extra battery, power the computer off.

If the hibernation function is set

Red indicator lights

Beep sounds**

Hibernation Mode

(at approx. 9% capacity)

(at approx. 4% capacity)

**When disabling the speakers with the Setup Utility (or pressing

disabled.

), the warning beep is also

If the hibernation function is not set

Computer

goes off

Red indicator lights

Beep sounds

(at approx. 4% capacity)

(at approx. 9% capacity)

(at approx. 0% capacity)

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Battery Pack

Precautions

Care should be exercised with regard to the following in order to avoid the possibility of

liquid leakage, overheating, or bursting.

• Do not throw the battery pack into a fire or expose it to heat.

• Do not place the battery pack together with articles such as necklaces or hairpins when

carrying or storing.

• Do not insert sharp objects into the battery pack, expose it to bumps or shocks, deform,

disassemble, or modify it.

• Do not short the positive (+) and negative (-) contacts.

• The battery pack is a rechargeable battery intended for use with the CF-35 series or the

specified charger (CF-VCB251A). Do not use it with a computer other than the one for

which it was designed.

• Do not charge, use or leave the battery pack for extended periods where it will be exposed

to direct sunlight, in a hot place (in an automobile on a sunny day, for example), or in a

cold place.

Do not touch the terminals on the battery pack. The battery pack may no longer function

properly if the contacts are dirty or damaged.

Do not expose the battery to water, or allow it to become wet.

Do not put the battery into a microwave oven or a pressurized chamber.

This computer prevents overcharging of the battery by recharging only when the remain-

ing power is less than approx. 95% of capacity.

If the battery should leak and some of the fluid get into your eyes, do not rub your eyes.

Immediately flush eyes with clear water and see a doctor for medical treatment as soon as

possible.

Should the battery emit an abnormal odor, become hot to the touch, become discolored,

change shape, or become in any way different from normal, remove it from the unit or

charger and discontinue use.

If the battery pack will not be used for a long period of time (a month or more), charge the

battery pack until the remaining battery become 30% to 40% and store it in a cool, dry

place.

NOTE

The battery pack may become warm during recharging or normal use. This is com-

pletely normal.

Recharging will not commence outside of the allowable temperature range (5 °C to 35

°C (41°F to 95 °F)). To allow the battery to charge, adjustments have to be made to the

temperature. Once the allowable range requirement is satisfied, charging begins auto-

matically. Note that the recharging time varies based on the usage conditions.

If the temperature is low, the operating time is shortened. Therefore, please use the

computer within the allowable temperature range.

Although the battery has not begun to run down, the battery indicator may light up red

or emit a beep. This indicates a significant rise in the temperature of the battery pack.

This is typically caused by the fact that the battery pack has been delivering a high level

of power because the computer has been used with the display at the brightest setting

and with the power-saving function off. In order to protect the battery pack from tem-

perature rises, the computer's processing speed is automatically reduced and the battery

temperature is brought down. It is also a good idea to connect the AC adapter, set the

power-saving function, and turn down the brightness of the display. When the tempera-

ture has dropped, the computer's regular processing speed will be restored.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Battery Pack

Replacing the Battery Pack

When the charge provided by your battery pack is supplied for only a short period of time, even

after fully charging according to the instructions, it may be time to replace your battery pack.

The battery pack is a consumable item and therefore will require replacement (CF-VZS351).

CAUTION

The charging terminal of the battery pack is used for charging

using the battery charger (CF-VCB251A), which is sold separately.

Never connect anything to the charging terminal other than the

exclusive adapter that is supplied with the battery charger.

Charging Terminal

Doing so could damage the device connected to the battery pack, the cable, and the

battery pack itself, as well as resulting in overheating or bursting.

Power off your computer ( page 10)

Do not shut down using the suspend mode.

CAUTION

In the suspend mode, do not remove/change the battery pack. Removing the pack

in the suspend mode will erase your data and may damage the computer.

Hook

Remove the battery pack cover

Open your display. After pressing the hook on the bottom of the computer, slide to

remove the cover.

Tape

Taking out the battery pack

Pull the tape on the battery pack and remove it from the computer.

Inserting a battery pack

Push the pack in until it is in place.

Reattach the battery pack cover

Slide the cover in until it snaps into place.

CAUTION

Make sure to properly remove and reattach the cover. Using

excessive force (e.g., trying to snap it back into place) may

cause the cover to break.

An improperly attached cover may allow your battery pack

to fall out while you are carrying your computer.

NOTE

Besides the AC adapter (CF-AA1526) an optional battery

charger (CF-VCB251A) is available. This device is convenient

in that it allows you to charge another battery pack while you

are using the computer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Security Measures

To prevent unauthorized access of your computer the various security measures are provided below.

Situation

Function to use

User Password

Reference

below

You do not want your computer to be used without permission

Same as above, but while you’re away temporarily

You want to prevent theft or damage to data by using a floppy disk

Coffee break Password

Prevent operation by using a floppy disk

Remove floppy disk drive

Supervisor Password

Use a security lock

page 18

page 19

page 22

page 19

page 39

You do not want your Supervisor Setup changed without permission

You want to prevent theft of your computer

When you do not want your computer to be used without permission

Set the User Password.

Without the password, access to your computer is impossible.

When the User Password is set

Upon entering your User Pass-

If the correct pass-

word and pressing

word is input,

Will Start

Over three incorrect

attempts,

Will Not Start*

(Power off)

* If you are starting from the suspend mode (

page 10), if after three

attempts the correct password is not input, or if no password is en-

tered for about a minute, the computer returns to the suspend mode.

Setting the user password (enabling, changing, disabling)

Run the Setup Utility ( page 36)

Using

and

, select [System Setup] then press

, select [User Password] then press

4 ^Using

To enable or change your password

Enter your password at the [Enter User Password], then press

CAUTION

Your password will not be displayed on the screen.

Please limit your password to seven characters. Note that there is no

distinction between upper and lower case letters.

White colored keys can be used. Note that space bar and function keys

cannot be used.

Do not input your password while holding down on the

Use only the upper horizontal row of numeric keys to input user pass-

words. The numeric keys combined with alphabet keys on the lower key-

board cannot be used.

Do not forget your password. If a password is forgotten you will be

unable to use your computer.

To disable your password

Using the

and

keys, select [Delete User Password] then press

. Go

to step 7.

Re-enter your password at the [Enter User Password Again]

(This is for confirmation purposes.)

Using

and

, select [Set User Password] then press

At the confirmation screen, press

Download from Www.Somanuals.com. All Manuals Search And Download.

Security Measures

Press

to end the password setting procedure

Close the Setup Utility ( page 36)

CAUTION

To prevent the changing of your password without permission

• When running the Setup Utility program, do not leave your computer even for a

short time.

• Set the User Password Protection option ( page 20).

You do not want your computer to be used without permission while away temporarily

You should set the “Coffee break Password” (Note that you must first set the User Password).

When you input your selected key combination, the computer locks (key input, use of the touch

pad and use of an external mouse are no longer possible).

When the coffee break password is set

When leaving your desk

(Example of a selected key combination)

Input the correct password used at startup

and press

Operation resumes

Operation does

not resume

The computer

is locked

When an incorrect password is inputted,

CAUTION

Do not leave your computer just after sensitive data had been shown on the screen.

It is impossible to lock your computer from an external device, such as a mouse

connected through the serial port.

During the coffee break,

is displayed on the screen. If the operations de-

indication may

scribed below are performed during the coffee break, the

disappear. In order to quit the coffee break and begin using the computer, input

your password.

If a different popup window is displayed by using the

key combination.

If the computer is returned from the standby mode.

If the serial mouse is moved.

Setting the Coffee break Password (enabling or disabling)

Set the User Password ( page 17 step 1 to 7), if it hasn’t already

To enable the Coffee break Password

Using

and

, select [Coffee break Password] then set [Enable] with

To disable the Coffee break Password

Using

and

, select [Coffee break Password] then set [Disable] with

Go to step 4.

Using

and

keys, select [Key Combination for Coffee

break] then set your combination of keys with

Press to end the password setting procedure

Close the Setup Utility ( page 36)

Download from Www.Somanuals.com. All Manuals Search And Download.

When you want to prevent theft of or damage to data by using a floppy disk

You may choose to protect the data on your computer from being accessed illegally or over-

written accidentally by using a floppy disk. You can also set your computer to be unbootable

from a floppy disk.

NOTE

To prevent the use of floppy disks altogether, you may also choose to remove the floppy

disk drive ( page 22).

Preventing the use of a floppy disk

This error message is displayed.

Even when one tries to access a

floppy disk,

Procedure

Run the Setup Utility ( page 36)

Using

and

, select [Supervisor Setup] then press

Using

and

, select [Boot Up Drive] then set either [HDD

FDD] or [CDD

CAUTION

FDD

HDD] with

When changing to [HDD

FDD] or [CDD

FDD

HDD] setting, to

continue read/write operation from a floppy disk and to use the hard disk drive or

CD-ROM to start, press

and go to step 5.

Using the

and

, select [Floppy Operation], set [Disable]

5 ^with

Close the Setup Utility ( page 36)

then press

When you do not want your Supervisor Setup changed without permission

Set the Supervisor Password. After it has been set, no changes can be made to the Supervisor

settings unless the password is entered.

When the supervisor password is set

In the Setup Utility ( page 36),

is displayed,

Input the correct supervisor password and press

Supervisor Setup

May be

Opened

Supervisor Setup

Can not be

Opened

When the supervisor password is incorrect or when the

user password is entered, (Or, even when the correct su-

pervisor password is entered. ( page 31))

(There are cases in which the Supervisor Setup does

not appear on the main screen ( page 36)).

NOTE

You may wish to protect the User Password ( page 20).

Download from Www.Somanuals.com. All Manuals Search And Download.

Security Measures

Setting the Supervisor Password

(enabling, changing, disabling)

Run the Setup Utility ( page 36)

Using

and

, select [Supervisor Setup] then press

Using

and

, select [Supervisor Password] then press

To enable or change your supervisor password

Enter your password at the [Enter Supervisor Password], then press

CAUTION

Your password will not be displayed on the screen.

Please limit your password to seven characters. Note that there is no dis-

tinction between upper and lower case letters.

White colored keys can be used. Note that space bar and function keys

cannot be used.

Do not input your password while holding down on the

Use only the upper horizontal row of numeric keys to input user pass-

words. The numeric keys combined with alphabet keys on the lower key-

board cannot be used.

Do not forget your password. If a password is forgotten you will be un-

able to use your computer.

To disable your supervisor password

Using

and

, select [Delete Supervisor Password] then press

. Go to

step 7.

Re-enter your password at the [Enter Supervisor Password

Again]

(This is for confirmation purposes.)

NOTE

When you do not want the User Password enabled, changed, or disabled

without permission,

use

and

to select [User Password Protection], then set [Enable] with

Using

and

, select [Set Supervisor Password] then press

At the confirmation screen, press

Press

to end the password setting procedure

Close the Setup Utility ( page 36)

Download from Www.Somanuals.com. All Manuals Search And Download.

Infrared Data Communications

Your computer is equipped with an infrared communications port enabling you to transfer

data without a cable.

Preparations for Infrared Data Communications

Set the address of your infrared communications port to enable.

Position your computer so that the port is face-to-face with the port of another

computer.

Be sure the computers are not in direct

contact with one another.

A port-to-port distance of 20 to 50 cm

(8 to 20 inches) is recommended.

Infrared Communication

Port

CAUTION

In the Setup Utility, select [IrDA] in the [Supervisor Setup] and set [Automatic (PnP)]

or [2F8]. Setting [OFF] will make infrared data communications impossible.

Problems with infrared data communications

An object is located between both ports.

There are other electronic devices nearby causing interference, such as, a television,

VCR, wireless headphone, etc.

Direct sunlight or white glowing light, such as fluorescent lighting; can cause inter-

ference with communications between the ports.

RunningTranXit^TM

TranXit comes preinstalled and allows you to perform infrared data communications such

as transfer data and update information between two computers. Note that both computers

need to have TranXit installed and running.

Running the program

Select [TranXit] from [Start] -

[Programs] - [TranXit].

NOTE

Online help is available on how to use

TranXit. Click [TranXit Quick Reference

Guide] in [Start] - [Programs] - [Panasonic].

(Reinstalling TranXit;

page 34)

Setting or changing the“Computer Name”

It is necessary to assign a different “Computer Name” to each computer; select [Com-

puter Name] in [Setup] to change the name.

CAUTION

In [Control Panel]-[Add New Hardware], if [Infrared] is added, TranXit can not be

used. For TranXit to be operable, [Infrared] must not be set.

Exit TranXit software before entering the suspend or hibernation mode. Start TranXit

again after the computer resumes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Add-ons/Peripherals

Devices capable of being used by your computer are listed in the table below.

Where to connect

Multimedia Pocket

PC Card Slots

Device(s)

Reference

below

CD-ROM drive (CF-VCD351)

PC Cards (Modem, LAN, SCSI, etc.)

Serial Devices (Mouse, Modem, etc.)

Extra Memory

Port Replicator (CF-VEB351)

External Display

page 23

page 39

page 24

page 25

page 39

Serial Port

RAM Module Slot

Expansion Bus Connector

Ext. Display Port

Parallel Port

Ext. Keyboard/Mouse Port

Headphone Jack

Microphone Jack

Printer

Keyboard, External Mouse [Type PS/2], etc.

Speaker/Headphone

Microphone

Using a CD-ROM Drive

You may use an optional CD-ROM pack (CF-VCD351) by removing your floppy disk drive

from the multimedia pocket. Should you decide to install the CD-ROM pack, it will function

as an internal CD-ROM drive. For more information, please read the manual that accompa-

nies the CD-ROM pack.

Installing/Removing the Unit

Power off your computer ( page 10)

Do not shut down using the suspend or hibernation mode.

CAUTION

Do not install or remove peripherals while your computer is in the suspend or

hibernation mode; abnormal operation may result.

^{MP Release Lever}2

Removing the unit

Turn your computer over, slide the MP release lever using thumb and remove the

unit.

CAUTION

Please handle the unit as shown (holding both sides).

Otherwise, the unit may be damaged.

Do not allow dust to enter the multimedia pocket.

Groove

Use of the dummy FDD is highly recommended

when the floppy disk drive is not installed. When

inserting the dummy FDD, first make sure the guide

and groove match and then push the guide part of

the dummy FDD in.

Guide

The lever will return to this position

(right-side).

Installing the unit

After the lever returns to its original position, continue pushing in the unit from

both edges until it is firmly set.

Turn your computer on

CAUTION

You may use the floppy disk drive as an external unit that is connected through the

parallel port, by using an optional FDD cable (CF-VCF351). Some precautions are

necessary, as described below, since problems may arise.

• Do not move the drive while accessing data on the floppy disk.

• Firmly hold both sides of the drive when removing a disk. Excessive force on top

should be avoided.

NOTE

Even after installing the CD-ROM Pack, [Removable Disk (A:)] is displayed in [My Com-

puter], but access is not possible. Select [Cancel].

Download from Www.Somanuals.com. All Manuals Search And Download.

Using PC Cards

Your computer has two PC Card slots. These slots conform to the PC Card Standard; there-

fore, communications and SCSI devices may be utilized. The slot allows you to use two Type

I or Type II cards (or one Type I and one Type II), or one Type III card.

Type I or II

Two cards can be used simultaneously.

Type III

One card can be used only in the bottom slot.

Bottom Slot

CAUTION

PC Card Slots

Please check the PC Cards’ specifications. Be sure the total operating current does

not exceed the specified limit. Damage may result otherwise.

Allowable Current (total for two slots) : 3.3 V: 400 mA, 5 V: 400 mA, 12 V: 120 mA

There are times when both a Type I card and a Type II card will not work at the same time.

SRAM and FLASH ROM (except for ATA interface) cards are not supported.

When using a CardBus type card, use only that card; do not insert any other PC Cards.

Only the bottom slot can support a Zoomed Video (ZV) card.

Installing/Removing the PC Card

Power off your computer ( page 10)

Do not shut down using the suspend or hibernation mode.

CAUTION

Do not install or remove peripherals while your computer is in the suspend or

hibernation mode; abnormal operation may result.

Before removing a PC Card, go to [Socket Status] (in [Start] - [Settings] - [Control

Panel] - [PC Card (PCMCIA)]), select the PC Card slot and press [Stop].

Button

Removing the PC Card (or the dummy card)

Pull the button out and then press it.

NOTE

Dummy cards are provided at the time of purchase. They provide protection

for the PC Card slots against such things as dust.

Installing the PC Card

Simply slide the PC Card in until it snaps into place.

Please refer to the manual for each card on how to install the card (insertion is

typically label-side up).

Turn your computer on

Label-side up

There are some PC Cards that require special or updated device driver be installed.

Follow the instructions on the screen and read any related manuals on how to install

these device drivers.

NOTE

You may need to install a driver from the Windows 95 CD-ROM (included) or a PC Card's floppy disk. Simply follow the

on-screen instructions and read the PC Card's operation manual on how to install the driver.

PhoenixCard Manager95:

Follow the installation procedure below only if you will be using the ZV card. Otherwise, do not perform the installa-

tion; abnormal operation may result.

1 Set [Sound Chip] to [Automatic (PnP)] in the Setup Utility.

2 Select [Start] - [Run] and type [c:\util\phoenix\disk1\setup.exe] press

, and then follow the on-screen in-

structions.

If PhoenixCard Manager95 has been reinstalled, follow the instructions in “Installing PhoenixCard Manager95" on

page 34.

After PhoenixCard Manager95 has been installed, make sure to power off the computer before installing or removing

the card. Also, do not use the suspend or hibernation functions if the card is installed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Add-ons/Peripherals

Adding Memory

CAUTION

RAM modules are extremely sensitive to static electricity. There are cases where static

electricity generated by the human body has adversely affected such modules. In addi-

tion, it is easy to damage the RAM modules or internal components of the computer.

Therefore, when installing or removing a RAM module, handle the module with extreme

care.

Installing/Removing the RAM Module

Power off your computer ( page 10)

RAM module specifications

144 pins, 60/70 ns, 3.3 V,

SO-DIMM, EDO

Do not shut down using the suspend or hibernation mode.

CAUTION

Do not install or remove peripherals while your computer is in the suspend or

hibernation mode; abnormal operation may result.

Remove the memory cover after removing the screw holding

it in place

Turn your computer over and use a screwdriver to remove the screw.

CAUTION

Do not touch the terminals or internal components, insert objects other than the

module, or allow foreign particles to enter. Doing so has been known to cause

damage, fire or electric shock.

Installing the RAM module

Slide the module in at an angle.

2 Snap the module into place by pushing it down.

RAM Module Slot

Removing the RAM module

Open the left and right hooks.

Gently remove the RAM module from the slot.

Hooks

Put the cover back into place, then fasten the screw

Turn your computer on

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting a Port Replicator

A port replicator is available as an option (CF-VEB351). This device eliminates the hassles of

having you connect/disconnect the various cables when carrying your computer around and

allows a variety of peripherals to be connected including a headphone or microphone, etc.

The port replicator connects to the expansion bus connector on the bottom of your computer.

When your computer is not connected to the port replicator, be sure that the expansion bus

connector on the bottom of the computer is covered.

For more detailed information, please refer to the operation manual for the port replicator.

Using an External Display

1 _{Power off your computer (}

page 10)

Do not shut down using the suspend or hibernation mode.

CAUTION

Do not install or remove peripherals while your computer is in the suspend or hiber-

nation mode; abnormal operation may result.

2 _{Connect the external display to your computer}

Ext. Display Port

NOTE

For more detailed information, please refer to the operation manual for the external

display.

Turn on the display, then turn on your computer

To display on both the LCD of your computer and the external

display

Run the Setup Utility ( page 36).

Using

and

, select [System Setup] then press

, select [Display], set [Simultaneous] with

then press

4 Close the Setup Utility ( page 36).

Select your external display

Set your external display for [Models] in [Start] - [Settings] - [Control Panel] -

[Display] - [Settings] - [Advanced Properties] - [Monitor] - [Change] - [Show all

devices], then press

Using a Printer

1 _{Power off your computer (}

page 10)

Do not shut down using the suspend or hibernation mode.

CAUTION

Do not install or remove peripherals while your computer is in the suspend or hiber-

nation mode; abnormal operation may result.

Connect the printer to your computer

NOTE

Parallel Port

Some printer cables may be difficult to connect, and may require removal of the rear

cover. Take care not to lose the cover.

Turn on the printer, then turn on your computer

Download from Www.Somanuals.com. All Manuals Search And Download.

Add-ons/Peripherals

Setting your printer

Go to [My Computer] - [Printers]. Find your printer’s icon, double-click on it, and click

[File] - [Set As Default]. If no icon is available, select [Add Printer] and install the

driver program.

NOTE

You may need to install a driver for your printer. Simply follow the on-screen instruc-

tions and refer to the operation manual for the printer on how to install the driver.

To change your hard disk, consult your nearest Panasonic Dealer or authorized Service Center

CAUTION

To Customers:

To change your hard disk, consult your nearest Panasonic dealer or authorized Ser-

vice Center.

Be sure to back up all important data before the change.

To Technicians (at a Panasonic dealer or authorized Service Center):

Be careful when replacing the hard disk. The hard disk is extremely sensitive to shock.

In addition, static electricity could later affect some internal components.

Installing/Removing the hard disk

(For technicians at Panasonic dealer or authorized Service Center)

Power off your computer ( page 10)

Do not shut down using the suspend or hibernation mode.

CAUTION

Do not install or remove peripherals while your computer is in the suspend or

hibernation mode; abnormal operation may result.

2 _{Loosen the screw, then take off the cover}

Turn your computer over. Then, loosen the screw with a screwdriver and with the

display slightly open, remove the cover.

Removing the hard disk

Pull the tape attached to the hard disk to disconnect the connector on the hard disk

from the connector on the computer. Next, remove the hard disk from the pocket.

Tape

Connector - computer

Installing the hard disk

Make sure the hard disk connector is located on the top side. Push the disk in so

that it connects firmly with the connector on the computer.

Connector - hard disk

Put the cover back into place, then fasten the screw

With the display slightly open, reattach the cover.

CAUTION

Set the hard disk tape as shown so that it does not get in

the way when replacing the cover.

Download from Www.Somanuals.com. All Manuals Search And Download.

Usage, Carrying and Maintenance

Usage Environment

Environment

Places not to use your computer

Place the computer on a flat stable surface.

Such areas may result in damage to the computer.

Areas exposed to direct sunlight

In use:

Temperature: 5 °C to 35 °C

(41 °F to 95 °F)

Areas with electronic equipment

Humidity:

30% to 80% RH

These areas may interfere with your

display or cause your computer to

produce strange sounds.

(No condensation)

Not in use: Temperature: -20 °C to 60 °C

(-4 °F to 140 °F)

Areas with extremely high/low temperatures

Humidity:

30% to 90% RH

(No condensation)

Do not leave things near the computer that are sensi-

tive to heat. During operation, the computer can be-

come quite hot.

Carrying

It is a good idea to make backup copies on floppy disks and carry them with you.

Do not leave a floppy disk in the drive while transporting your computer.

Do not carry your computer when it is ON.

Remove all cables before transporting your computer. Having the optional Port Replicator

(

page 25) is very convenient.

We recommend preparing a fully charged battery (and optional charger, if possible).

When transporting spare batteries inside a package, briefcase, etc., it is recommended that

the batteries be stored in a plastic bag.

Do not carry the computer while the display is open, or carry it by gripping the display.

Do not put anything (e.g., a piece of paper) between the display and keyboard.

Do not drop or hit your computer against solid objects.

If you have occasion to ship your computer, make absolutely sure that it is packed with

adequate protection.

When flying

Always carry your computer with you. Never check it with luggage.

Maintenance

Do not use a dry/wet (with water) cloth to wipe

the display. We recommend cleaning the display

with a soft cloth applied with isopropyl alcohol or

ethyl alcohol. Please do not use other types of

chemicals.

Do not use solutions such as benzene or thinner.

A soft, dry cloth is recommended.

When oil accumulates on the surface of the touch

pad, use a damp cloth with dish washing liquid to

wipe the surface, or a compact cassette head

cleaner to remove the oil. The cursor may not

move well when the surface is not clean.

Download from Www.Somanuals.com. All Manuals Search And Download.

Computer Diagnosis

List of Error Codes

If a problem occurs with your hardware, [POST Start up Error(s)] is displayed along with the

error code(s), follow the on-screen instructions.

Setup: Setup Utility ( page 36) is started. Run [Load Default Settings (PnP)].

Next the Setup Utility must be run again to input the appropriate operating environ-

ment settings.

Exit:

Ignore the error message(s), and restart the computer.

Code

Description

062

101

102

106

114

151

161

162

163

173

201

Boot failure--default configuration used

System Board Failure

Adapter ROM Error

System Board Failure

Bad CMOS Battery

Configuration Change Has Occurred

Configuration Error

Date and Time Incorrect

Configuration Change Has Occurred

Memory Size Error

Keyboard Error

Default configuration in use

Interrupt controller failure

Timer 2 test failure

Diskette controller failure

Adapter ROM checksum error

Real-time clock failure

Dead battery

Configuration error

CMOS checksum error

Real-time clock is not updating

ROM configuration has changed

Memory size/data error

301

Keyboard failure

303

604

605

Keyboard Error

Keyboard controller failure

Diskette drive 0 failure

Diskette unlocked problem

Fixed disk 0 failure

Diskette Drive Error

Hard Disk Error

PCI Error

1780

1800

1801

1802

1803

1804

1805

1962

8601

No more IRQs available

No more room for optional ROM

No more I/O space available

No more memory (above 1 MB) available

No more memory (below 1 MB) available

Checksum error or 0 size optional ROM

An operating system could not be found

Pointing device failure

IPL Error

Pointing Device Error

I9990301 IPL Error

I9990305 IPL Error

Hard disk failure

An operating system could not be found

Using the Self-diagnosis Program

Follow the procedure below to check whether each part of your computer is operating properly.

To run the program, insert the Firstaid FD you created into the

floppy disk drive, then turn your computer on

When the display below is shown, select [1. Boot]

1. Boot

2. Restore HDD to factory default (For beginners)

3. Restore HDD to factory default (For advanced users)

At the MS-DOS prompt (A:\WINDOWS\COMMAND>), input the

following:

diag35

Follow the messages on the screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Dealing with Problems

When a problem occurs, please refer to this page. If you think it has to do with the software application you are using, please

read the related manual. If for some reason you still cannot figure out the problem, please consult your nearest Panasonic dealer.

Starting Up

The power indicator ( ) or

battery indicator ( ) is not

lit

Check the cable connection for the AC adapter (

Check to see if a fully charged battery is properly installed (

Pressing the reset button will solve the problem ( page 39).

page 7).

page 16).

Please input your password. If you have forgotten it, consult your nearest Panasonic dealer.

is displayed

If before you double-click

[c:\util\avapp\psetup.bat], and press

it disappears, select [Start]-[Run], input

. Follow the message on the screen.

is not displayed

(Once this icon is executed, it will

not be displayed later)

is not displayed

Select [Start]-[Run], input [c:\util\avapp\manual\seticon.bat], and press

page 28

[Post Start Up Error(s)] is

displayed

Run [Load Default Settings (PnP)] in the Setup Utility. This will restore the Setup Utility's

settings to their default values (except the password settings), then the Setup Utility must be run

once again for you to input the appropriate operating environment settings. (The processing

speed depends on the application software used, so this operation may not cause the processing

speed to increase.)

The pre-memory count,

Windows startup, or an

operation is extremely

slow

You can set the date and time through [Date/Time] in [Start] - [Settings] - [Control Panel].

Another way is with the DATE and TIME commands in MS-DOS.

The date and time are

incorrect

If you continue to experience problems, the internal battery maintaining the clock may

need to be replaced. Please consult your nearest Panasonic dealer.

Battery Indicator

The battery level is low. Connect the AC adapter or replace the battery pack with a fully

charged one. If you have neither the adapter nor an extra battery, save your data and

power off your computer.

The red battery indicator

lights or the beeps sound

while the computer is in use.

The temperature has risen due to a big load. Attach the AC adapter to take the load off the

pack.

The battery pack or recharging function may be defective. Quickly remove the battery

pack and disconnect the AC adapter, then connect them again.

If the problem persists, consult your nearest Panasonic dealer.

When the battery pack is fully charged, turn on your computer, unplug the AC adapter, and

then completely discharge the battery.

The red indicator blinks

The red indicator lights for

an extended period of time

Unable to charge because of an improper temperature range (

page 15).

After the AC adapter is

connected, the orange indi-

cator blinks five times

Download from Www.Somanuals.com. All Manuals Search And Download.

Dealing with Problems

Display

No display after powering

on;

............

The brightness can be adjusted with

Dark

Bright

For models with an DSTN display, you can adjust the contrast with

When purchasing the computer, the display setting has been preset for an external display. If

you connect the external display, the screen is displayed on the external display.

When there is no display to an external display,

• Check your cable connection for an external display.

• Confirm your display is on.

If your computer is connected to an external display and the internal LCD has been set to

"off", and the computer is placed in the hibernation or suspend mode, the internal LCD

will remain in the "off" mode if the external display is not connected when the computer

is restarted. In this case, re-connect the external display and reboot the computer.

Has the computer been set to the power-saving mode?

To resume operation of your computer, press any key.

To save power, your computer may have automatically entered the hibernation mode.

The power has not been cut,

but after a certain period of

time, there is no display

If an image is displayed for a prolonged period of time, an afterimage may appear. This is

not a malfunction. The afterimage will disappear when a different screen is displayed.

An afterimage appears

[Start]-[Settings]-[Control Panel]-[Mouse]-[Motion] and check [Show pointer trails].

The motion of a mouse

cursor is not smooth

Disk Operations

Has the floppy disk been correctly inserted?

Has the floppy disk been correctly formatted?

Cannot read/write to a

floppy disk

Your floppy disk drive may not have been properly set in the multimedia pocket.

Has the Setup Utility been used to set [Floppy Operation] to [Enable]?

Is the floppy disk write-protected?

Unable to write to a floppy

disk

Select [Format] in [My Computer] - [3 1/2 Floppy (A:)] - [File]. After confirming the disk

How to format a floppy disk

is unclear

volume and format type, click

Unable to read/write to the

hard disk

Your drive or file may not have been properly set.

Check to see if the hard disk is full.

Your hard disk content may be corrupted. Consult your nearest Panasonic dealer.

Character Input

Unable to input anything

but numerals

and

are on, the Numeric Key Pad is ON. To switch it OFF, press

Only capital letters are

being input

is on, the Caps Lock is ON. To switch it OFF, press

How to input European

characters (ß, à, ç) or

symbols is unclear

Select [Start] - [Run], input [c:\windows\charmap.exe] and press

Map will be displayed. Point to the desired font name and select it.

. The Character

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Utility

Enter the User Password or Supervisor Password. If you have forgotten it, consult your

nearest Panasonic dealer.

is displayed

[Supervisor Setup] is not

displayed in the menu

At the start of the program when

word.

is displayed, you have to enter the Supervisor Pass-

When both the User Password and Supervisor Password have been set, if you enter the User

Password, [Supervisor Setup] will not be displayed ( page 36).

If [Supervisor Setup] is not displayed even after entering the Supervisor Password, you have

to disable the User Password. Run the Setup Utility program again, and input the Supervisor

Password.

[User Password Protection] in [Supervisor Setup] may be enabled.

[User Password] cannot be

selected

You need to set the User Password.

[Coffee break Password]

or [Key Combination for

Coffee break] cannot be

selected

If the User Password has been set first, the Supervisor Password can not be the same as the

User Password. Another password needs to be entered.

[Supervisor Password]

cannot be set

Connecting Peripherals

Your peripheral does not

work (An error occurs while

installing the driver)

You need to use drivers conforming to Windows 95 Version 4.00.950B (OSR-2). Some

earlier drivers will no longer work.

For more information, please ask the manufacturer of the driver in question.

Unable to print

Check the computer-printer connection.

Make sure the printer is on.

Make sure the printer is in the online state.

Make sure paper is in the printer tray and there is no paper jam.

Has the Setup Utility been used to set [Parallel Port (Address)] to [Automatic (PnP)],

[378] or [3BC]?

The cursor does not move

from mouse operations

The Coffee break Password may be set.

Check your mouse connections, then reboot the computer from the keyboard.

From the keyboard, you may choose to press down on

then select [Shut Down].

Check the connection.

Confirm that the device driver for the serial port works. Please refer to the reference

manual for the device.

The device connected to the

serial port does not work

Confirm that two mouse devices are not connected, one through the ext. keyboard/mouse

port and the other through the serial port.

Try setting the [Touch Pad] to Disable in the Setup Utility.

Has the Setup Utility been used to set [Serial Port] to [Automatic (PnP)] or [3F8]?

Make sure the card is properly inserted.

A PC Card does not work

Confirm that the card conforms to the PC Card Standard.

A driver for Windows 95 may need to be installed.

Note that after a driver is installed, the computer must be rebooted.

Check that the proper port settings have been made.

Read the PC Card’s manual. Or, you may need to call the source of the PC Card.

page 24

You do not know the

available RAM module

Make sure the RAM module has been properly inserted.

The RAM module has not

been recognized

Check the address map by going to [View Resources] in [Start] - [Settings] - [Control Panel]

- [System] - [Device Manager] - [Computer] - [Properties].

The address map for IRQ,

I/O port address, etc. is

unclear

Download from Www.Somanuals.com. All Manuals Search And Download.

Reinstalling Software

Before Reinstallation

Preparation

You will need the CD-ROM included in the Windows 95 System Pack and the following 8 backup disks you made earlier.

• Firstaid FD (1 disk)

If for some reason, you

do not have these disks

or one of them is cor-

rupted, please consult

your nearest Panasonic

dealer.

• PanasonicTools Disk(1 disk)

• Drivers Disk 1/2 (2 disks)

•TranXit Disk (2 disks)

• PhoenixCard Manager Disk

(2 disks)

If you have not created these disks, a message will

appear at startup urging you to make backup cop-

ies. If there is no message, backup copies have al-

ready been created.

The CD-ROM pack (CF-VCD351) and FDD cable (CF-VCF351) are required for the following reinstallation procedure.

Mount the CD-ROM pack in the multimedia pocket and connect the FDD cable to the floppy disk drive. (Refer to the

operating instructions of the CD-ROM pack and FDD cable for details.)

Important

Save all important data. If reinstallation is carried out, all data existing prior to the installation will be lost. The reinstal-

lation will return the computer to factory condition.

Be sure to remove all PC Cards and disconnect all peripherals (except for the CD-ROM pack and FDD cable) before the

reinstallation procedure.

Be sure the AC adapter is connected until completing reinstallation.

Reinstalling

• Then, when the [Microsoft Windows 95 Startup Menu]

appears, for beginners, select [2. Restore HDD to fac-

tory default (For beginners)]. For advanced users, se-

lect [3. Restore HDD to factory default (For advanced

users)].

Windows 95 (HDD format)

Two options are available, one for beginners and the other

for advanced users.

For beginners:

Returning to factory default

condition.

• If the computer asks you to insert the Win95 Setup

CD-ROM, please set the Windows 95 CD-ROM that

comes with this computer. After inserting the Win-

dows 95 CD-ROM, Windows setup will start auto-

matically. (The whole process will take approximately

one hour).

For advanced users: Returning the primary MS-

DOS partition only to a condi-

tion similar to the factory de-

fault in cases where the hard

disk has been divided into mul-

tiple partitions.

CAUTION

NOTE

If the hard disk has been compressed, first remove the

disk compression.

With the exception of the instruction below, please

select all default values displayed by the Setup Wiz-

ard.

Be sure to add the check mark to [Sound, MIDI, or

Video Capture Card] at the [Analyzing Your Computer].

Have a blank disk on hand to create a "Windows 95

Startup Disk". Immediately after creating this disk,

enter the Firstaid FD into the floppy disk drive and

1 Insert the Firstaid FD, and turn the computer on, then

run the Setup Utility. ( page 36)

2 Select [Load Default Settings (PnP)], then press

At the confirmation message, press

3 Close the Setup Utility ( page 36); this screen should

press

. (Note: A system error will result if

appear.

the Firstaid FD is not inserted. If this occurs, insert

the Firstaid FD and press [Retry].

Microsoft Windows 95 Startup Menu

1. Boot

2. Restore HDD to factory default (For beginners)

3. Restore HDD to factory default (For advanced users)

5 At the [Finishing Setup], remove the floppy disk and press

. Windows will restart after all the settings have

automatically been made.

Enter a choice: 1

4 For beginners:

select [2. Restore HDD to fac-

tory default (For beginners)].

6 At the [Date/Time Properties], press

For advanced users: select [3. Restore HDD to fac-

7 At the [Add Printer Wizard], press

tory default (For advanced us-

ers)].

8 When the display appears indicating the establishment

of the system settings, press . The computer

At the confirmation message, press

the on-screen instructions.

. Simply follow

will reboot. (When the welcome screen appears, press

Download from Www.Somanuals.com. All Manuals Search And Download.

System setup

Sound Driver

21 In [Control Panel] - [System] - [Device Manager],

In [Start] - [Run], input [c:\install.bat] then press

Rebooting will be done automatically.

for each item in [Sound, Video and Game Con-

troller], press

to delete it, then press

10 In [Start] - [Programs] - [Windows Explorer], delete two

to confirm the deletion.

files named [install] on the C: drive.

• Select [PCMCIA socket] and if the [PCIC or

compatible PCMCIA controller] is displayed,

perform a similar delete operation.

Device Manager 1

11 In [Start] - [Settings] - [Control Panel] - [System] - [Device

Manager] - [View devices by connection], select [PCI bus] in

22 At the [System Properties], press

23 In [Start] - [Shut Down], select [Restart the com-

puter?] then press

24 At the [Update Device Driver Wizard of Unknown

[Plug and Play BIOS], press

, then press

• When the message appears to reboot your computer, press

. Rebooting will be done automatically.

• If the computer asks you to insert the Windows 95 CD-

ROM, please set the CD-ROM and press

• At the [New Hardware Found], [L:\WIN95] is displayed.

Rewrite this to [D:\WIN95].

Devices], press

25 Select

then press

, type [c:\util\drivers\sound],

• Then, when the [Version Conflict] appears, select

12 Press at the [Update Device Driver Wizard of Intel

82371AB PCI Bus Master IDE Controller] and

26 At the [Update Device Driver Wizard of

YAMAHA OPL3-SAx Sound System], press

then press

27 At the [Copying Files], type [c:\util\drivers\sound]

for the source then press

at the [Insert Disk].

•

If [Update Device Driver Wizard of Intel 82371AB PCI

Bus Master IE Controller] is not displayed, please go to

step13 after step 11.

28 In [Control Panel] - [Power] - [OPL3-SAx power

management], set [Non Power Save mode] then

Video driver

13 Press

press [Apply]. Then press

at the [Update Device Driver Wizard of Stan-

dard PCI Graphics Adapter (VGA)].

14 Select , input [c:\util\drivers\video], and

press . Then, press

15 At the [Insert Disk], select

Display

29 Set [High Color (16 bit)] for [Color palette] in

[Control Panel] - [Display] - [Settings]. Next, set

[Super VGA 1024 X 768] for [Models] in [Ad-

vanced Properties] - [Monitor] - [Change], then

16 At the [Copying Files], type [c:\util\drivers\video] and press

press

30 After pressing

, at the [Display Proper-

The display will ask you to restart Windows, press

(at times, the message may appear a few times)

ties] press

31 In [Start] - [Run], type [c:\util\updates\rmm2upd.exe]

then press

. Simply follow the on-screen

instructions.

Power Management

17 Delete the check mark for [When powered by AC power]

CD-ROM drive

and [When powered by batteries] in [Start] - [Settings] - [Con-

32 In [Control Panel] - [System] - [Device Manager]

- [CDROM] - [MATSHITA UJDCD8710] - [Set-

tings], delete the check mark for [Auto insert

notification], then set [L:] for [Reserved drive

trol Panel] - [Power] - [Disk Drives], then press

18 Set [Mobile or docking system] in [Control Panel] - [Sys-

tem] - [Performance] - [File System] - [Typical role of this

machine], and then press

letters] then press

33 At the [System Properties], press

When the message appears to reboot your com-

Device Manager 2

19 Add the check mark

for [Get IRQ table from PCIBIOS

puter, press

. Rebooting will be done

2.1 call] in [Device Manager] - [System devices] - [PCI bus]

automatically.

- [IRQ Steering], then press

20 At the [System Properties], press

. The display will

CAUTION

ask you to restart Windows. Remove the floppy disk and press

In [Control Panel]-[Add New Hardware], if [Infra-

red] is added, TranXit can not be used. For TranXit

to be operable, [Infrared] must not be set.

Download from Www.Somanuals.com. All Manuals Search And Download.

Reinstalling Software

NOTE

Installing Internet Explorer

Some Windows applications differ in use from their fac-

tory-set state. To add or delete items from the menu,

select [Add/Remove Programs] in [Start] - [Settings] -

[Control Panel].

Reinstalling Windows 95 causes an older version of Internet

Explorer to be installed.

To return the computer to the state it was in when you pur-

chased it, follow the steps below to install the newer version

Internet Explorer.

CF-35PJJ8C M/CF-35PJJ8C E

Installing TranXit

1 Insert the Internet Explorer CD-ROM included in the Win-

dows 95 System Pack into the drive and select [Start] -

[Settings] - [Control Panel] - [Add/Remove Programs].

If necessary, install TranXit with the following steps.

1 Insert TranXit Disk 1 into the drive and select [Start] -

[Settings] - [Control Panel] - [Add/Remove Programs].

2 Select [Install/Uninstall] - [Install] and press

3 Type [L:\setup.exe], press

, then follow the on-

screen instructions.

3 Type “a:\install”, press

, then follow the on-screen

instructions.

NOTE

For all other models

To return to factory condition:

1 Insert the Windows 95 CD-ROM included in the Win-

dows 95 System Pack into the drive and select [Start] -

[Settings] - [Control Panel] - [Add/Remove Programs].

Set [Infrared] for [Connection Type] in [Connection

Setup] and press [Setup Connection]. Next, set [COM2]

for [Port] and [Panasonic Notebook Computer] for

[Models] in [Infrared device]. Select default values

for all other settings.

2 Select [Install/Uninstall] - [Install] and press

3 Type [L:\other\ie302\msie302.exe], press

, then

follow the on-screen instructions.

When the message appears to reboot your computer, press

. Rebooting will be done automatically.

4 Select [Add/Remove Programs] - [Install/Uninstall] -

Installing PhoenixCard Manager95

[Install] and press

. Type

[c:\util\ie302\auth2all.exe], press

the on-screen instructions.

When the message appears to reboot your computer, press

, then follow

If necessary, install PhoenixCard Manager95 with the follow-

ing steps.

. Rebooting will be done automatically.

CAUTION

Follow the installation procedure below only if you will be

using the ZV card. Otherwise, do not perform the installa-

tion; abnormal operation may result.

NOTE

1 Insert PhoenixCard Manager95 Disk 1 into the drive and

select [Start] - [Settings] - [Control Panel] - [Add/Remove

Programs].

At the time of purchase, the [CF-35 series Quick Guide]

can be found under [Favorites] in the Internet Explorer

program. If reinstallation is carried out for your com-

puter, this file will no longer be available. You may re-

install this file with following steps if necessary.

1 Select [Internet Explorer].

2 Select [Install/Uninstall] - [Install] and press

3 Type [a:\setup], press

, then follow the on-screen

instructions.

2 At the [Address], type [file://c:\util\avapp\manual\

manual.htm].

3 Once the page is displayed, select [Favorites] - [Add

to favorites] and input the name. Then press

Download from Www.Somanuals.com. All Manuals Search And Download.

Windows 95 Setup Procedure

This procedure explains step 4 on page 8 in more detail.

Select settings for your region, then press

Select your keyboard layout, then press

(for U.S.A.: United States 101, for U.K.: British)

Enter your name and your company’s name, then press

The License Agreement will be displayed.

After reading the agreement, select [I accept the agreement]

or [I don't accept the agreement] then press

If the former is selected, the [Certificate of Authenticity] will appear. If the latter is

selected, the Windows setup will be aborted.

Input the Product Number written on the “Certificate of Au-

thenticity”located in the “Introducing Microsoft Windows 95

book”that comes with this computer. After doing so, press

Press

If the instruction to restart appears, press

Insert the correct time, date and time zone and click

You can also complete these settings at a later time.

If you want to complete the printer settings, press

Simply follow the on-screen instructions.

If not, press

You can also complete these settings at a later time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Utility

Running the Setup Utility

To run the Setup Utility, you

need to restart your computer.

Upon seeing

this message

press

Press F1 for Setup

NOTE

The Setup Utility will not be run if

is not pressed soon after the computer restarts.

In this case, you need to restart your computer again.

If is displayed, enter your password.

If both the [User Password] and [Supervisor Password] have been set, after entering the

User Password, [Supervisor Setup] will not be displayed on the main screen.

To display the [Supervisor Setup]:

1 Use

2 Restart the computer and press

3 When is displayed, enter the Supervisor Password.

+ Power Switch to turn your computer off.

when [Press F1 for Setup] is displayed.

For more details, on-line help is available; press

Setup Utility

•System Setup

•Power Management

•Supervisor Setup

Save Settings

Restore Settings

Load Default Settings (PnP)

Load Default Settings (Non-PnP)

Return to the state existing at the time of Setup Utility

startup, or to the settings saved with [Save Settings].

Set default settings.

• (PnP) denotes “for Windows 95”.

• (Non-PnP) denotes “for other than Windows 95”.

• When the Supervisor Password has been set, input of

the password is necessary.

Exit Setup

Program Completion

• Hibernation settings ( page 11)

• Power Management settings ( page 13)

• Security Settings ( page 17)

• Add-ons/Peripherals Settings ( page 22)

After you have completed all settings, you may

exit the Setup Utility program.

NOTE

Key Operations

To display the correspond-

: To move among the items.

: To move among the values of

each item.

ing “help” file.

: To make a selection.

: To display previous screen

(To exit the program at the

main screen).

: To return to the setting before a

change.

: To set the default values.

Closing the Program

Exit Setup

NOTE

Settings were changed.

Do you want to save them?

If the User Password has been set, the password

must be entered before Windows can start.

Yes, save and exit the Setup Utility.

No, exit the Setup Utility without saving.

No, return to the Setup Utility.

(The display may be different if no changes to the settings are made.)

Download from Www.Somanuals.com. All Manuals Search And Download.

System Setup

NumLk

[ON]

[Enable]

[External Monitor]

Touch Pad

Speakers

Display

Setting the User Password ( page 17)

(Unable to select when the User Password Protection has been set.)

• User Password

Coffee break Password

Key Combination for Coffee break

User Password

[Enable]

³[Alt+Ctrl+F9]

User Password Status

Disable

Enter your new User Password twice.

Enter User Password

Enter User Password Again

[

]

Set User Password

Delete User Password

Power Management

Power Saving

[Standard (Battery)]

Enable

1 min

2 min

CPU Speed Change Mode

HDD Motor Timeout

Standby Timeout

page 13

Power Switch

[Hibernation]

[4 min]

Sets the function of the power switch.

Able to set how long the interval will be until hibernation.

Hibernation Timeout

Supervisor Setup

Parallel Port (Address)

[Automatic (PnP)]

[Bidirectional]

[Automatic (PnP)]

[Enable]

Parallel Port Mode

Serial Port

Sound Chip

Sound Blaster Compatible I/O [Automatic (PnP)]

WSS CODEC I/O

Sound IRQ-A

Sound IRQ-B

Sound DMA

[Automatic (PnP)]

[Enable]

CF-35PJJ8C M/CF-35PJJ8C

Sound DMA-A

Sound DMA-B

[Automatic (PnP)]

IrDA

Floppy Operation

Boot Up Drive

[FDD

HDD]

• Supervisor Password

User Password Protection

[Disable]

Setting Supervisor Password ( page 20)

Supervisor Password

Supervisor Password Status

Disable

Enter your new Supervisor Password twice.

Enter Supervisor Password

Enter Supervisor Password Again

[

]

When no external display is connected, display will be through the LCD.

Can only be selected when the [User Password] has been set.

Set Supervisor Password

Delete Supervisor Password

Can only be selected when the [Coffee break Password] has been set.

Can only be selected when the [Power Switch] has been set [Hibernation].

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Main Specifications

Model No.

CPU

CF-35PJJ8CAM/CF-35PJJ8CAE

CF-35KJF4BAM/CF-35KJF4BAE

Pentium^®Processor with MMX^TMtechnology Pentium^®Processor with MMX^TMtechnology

200 MHz

150 MHz

Cache Memory (second cache memory) 32 KB (256 KB)

32 KB (256 KB)

16 MB (80 MB Max. )

1.1 MB

EDO Memory (Expandable to)

Video Memory

32 MB (96 MB Max. )

1.1 MB

LCD

Type

12.1" (TFT)

Displayed 640 X 480 dots 256/65536/262144 colors

Colors 800 X 600 dots 256/65536 colors

Hard Disk Drive (including about 110 MB 3GB*

256/65536/262144 colors

256/65536 colors

2GB*

used specifically by the system)

1GB = 10⁹bytes

Other Specifications

Keyboard

Floppy Disk Drive

Windows 95 keyboard (for U.S.A.: 87 keys, for U.K.: 88 keys)

720 KB/1.44 MB (two-mode)

PC Card Slots

Two Type I or Type II, or one Type III

Allowable current

3.3 V: 400 mA, 5 V: 400 mA,

Slots

(total for two slots)

12 V: 120 mA

RAM Module Slot

Multimedia Pocket

Parallel Port

144-pin, 3.3-V, SO-DIMM

One slot (floppy disk drive included)

Dsub 25-pin female

Ext. Display Port

Serial Port

Mini Dsub 15-pin female

Dsub 9-pin male

Microphone Jack

Miniature jack, 3.5 DIA

Input impedance 600 Ω, Input voltage range 0.01 Vp-p

Miniature jack, 3.5 DIA

Headphone Jack

Impedance 32 Ω, Output Power 3mW (Impedance 32 Ω) X 2

Infrared Communication Port Data transmission speed:

Interface

CF-35PJJ8C M/CF-35PJJ8C E: 4 Mbps

For all other models:

115.2 kbps

Ext. Keyboard/Mouse Port

Expansion Bus Connector

Stereo Speakers (built in)

Mini DIN 6-pin female

Dedicated 100-pin female

Speakers

Sound

16 bits, 44.1 kHz PCM/FM sound (Sound Blaster PRO Compatible)

Operating System

Utility Programs

Microsoft^®Windows^®95 (FAT32 File System)

Diagnostics program, TranXit program,

PhoenixCard Manager program

Lithium Ion 10.8 V, 3300 mAh

Software

Battery Pack

Operating Time

Charging Time

Approx. 2.5 - 5.0 hours*

Battery

Power On

Power Off

Approx. 4.5 hours*

Approx. 2.5 hours*

Clock Battery

Coin type lithium battery 3.0 V

Operating Time

100 -240 V AC, 50 / 60 Hz Output

Approx. 10 years

15.1 V DC, 2.6 A

AC Adapter

Input

Power Consumption

Approx. 35 W** (maximum when recharging in the OFF state)

Physical Dimensions(W X H X D) 297 mm X 37.5 mm X 230 mm (11.7" X 1.5" X 9.1")

Approx. 2.2 kg (Approx. 4.9 lbs) (With the floppy disk drive installed)

Weight

* Varies depending on the usage conditions.

** Approx. 1.1 W when the battery pack is fully charged (or not being charged) and the computer is OFF.

LED Indicators (located below the display; explanation is from the left side)

CF-35 series Quick Guide

Green

Lit when the corresponding modes have been set.

Lit during access of the corresponding devices.

(Caps Lock) (Num Lock) (Scroll Lock) (Key Pad)

(CD-ROM)

(FDD)

(HDD)

Battery Status

Green

Power On

Download from Www.Somanuals.com. All Manuals Search And Download.

Names and Functions of Parts

CF-35EJC4BAM/CF-35EJC4BAE CF-35EVC4BAM

Display

Pentium^®Processor 133 MHz

_Dark........

Bright

Brightness Adjustment

16 KB (256 KB)

16 MB (80 MB Max. )

1.1 MB

16 KB

16 MB (80 MB Max. )

1.1 MB

12.1" (DSTN)

256/65536/262144 colors

256/65536 colors

1.44GB*

Darker contrast

Lighter contrast

Contrast Adjustment

(for DSTN display models only)

12.1" (TFT)

256/65536/262144 colors

256/65536 colors

1.44GB*

LED Indicators

page 38

Speakers

Keyboard

To adjust the volume*, select the

on the task bar then [Volume Control].

* You may also use the function keys to per-

Ventilation Hole

These holes allow heat to exit.

CAUTION

form this operation (

Speakers on/off :

Do not block or place the computer

in a location that may prevent

proper ventilation.

(The beep sound comes out from the left speaker

(and headphone). The sound level cannot be

changed.)

Power Switch

PC Card Slots

Touch Pad

page 10

Security Lock

CardBus Compatible

(Confirmation with the dealer required beforehand.)

A Kensington cable can

be connected to prevent

theft of your computer.

page 23

Multimedia Pocket

page 22

Battery Pack

page 15

USB Port: No software is provided.

Infrared Communication Port

Ext. Keyboard/Mouse Port

page 21

In some circumstances, if a PS/2 exter-

nal mouse with a serial interface con-

version function is connected to the port,

it may not operate normally.

Serial Port

DC-IN Jack

Parallel Port

Reset Button

page 25

When resetting your computer, use

a dull pointed object like a ball point

pen. Do not use a pencil. Pencil lead

can break off inside the computer and

damage the computer's circuit.

Ext. Display Port

page 25

Headphone Jack

Use this connector to con-

nect headphones or ampli-

fier-equipped speakers. Au-

dio output from the internal

speaker is disabled when

headphones or outside

speakers are connected.

Microphone Jack

Expansion Bus Connector

page 25

CAUTION

If a problem occurs but your

computer does not lock, we rec-

ommend not resetting the ma-

chine. Pressing the reset but-

ton will cause you to lose data

if an application is open.

RAM module slot

page 24

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED USE LICENSE AGREEMENT

THE SOFTWARE PROGRAM(S) ("PROGRAMS") FURNISHEDWITH THIS PANASONIC^®PRODUCT ("PRODUCT")

ARE LICENSED ONLY TO THE END-USER ("YOU"), AND MAY BE USED BYYOU ONLY IN ACCORDANCE WITH

THE LICENSETERMS DESCRIBED BELOW.YOUR USE OFTHE PROGRAMS SHALL BE CONCLUSIVELY DEEMED

TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE.

Matsushita Electric Industrial Co., Ltd. ("MEI") has developed or otherwise obtained the Programs and hereby licenses

their use to you.You assume sole responsibility for the selection of the Product (including the associated Programs) to

achieve your intended results, and for the installation, use and results obtained therefrom.

LICENSE

MEI hereby grants you a personal, non-transferable and non-exclusive right and license to use the Programs in

accordance with the terms and conditions stated in this Agreement.You acknowledge that you are receiving

only a LIMITED LICENSE TO USE the Programs and related documentation and that you shall obtain no title,

ownership nor any other rights in or to the Programs and related documentation nor in or to the algorithms,

concepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of

which title, ownership and rights shall remain with MEI.

You may use the Programs only on the single Product which was accompanied by the Programs.

You and your employees and agents are required to protect the confidentiality of the Programs.You may not

distribute or otherwise make the Programs or related documentation available to any third party, by time-sharing

or otherwise, without the prior written consent of MEI.

You may not copy or reproduce, or permit to be copied or reproduced, the Programs or related documentation

for any purpose, except that you may make one (1) copy of the Programs for backup purposes only in support

of your use of the Programs on the single Product which was accompanied by the Programs. You shall not

modify, or attempt to modify, the Programs.

You may transfer the Programs and license them to another party only in connection with your transfer of the

single Product which was accompanied by the Programs to such other party. At the time of such a transfer, you

must also transfer all copies, whether in printed or machine readable form, of every Program, and the related

documentation, to the same party or destroy any such copies not so transferred.

You may not remove any copyright, trademark or other notice or product identification from the Programs and

you must reproduce and include any such notice or product identification on any copy of any Program.

YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE

THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART.

YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY COPY THEREOF, IN

WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.

IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO ANOTHER PARTY, EXCEPT AS PER-

MITTED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED.

TERM

This license is effective only for so long as you own or lease the Product, unless earlier terminated.You may terminate

this license at any time by destroying, at your expense, the Programs and related documentation together with all

copies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions

therefor set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein.Upon

any such termination, you agree to destroy, at your expense, the Programs and related documentation together with all

copies thereof in any form.

YOU ACKNOWLEDGE THATYOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND

BY ITSTERMS AND CONDITIONS.YOU FURTHER AGREETHAT IT IS THE COMPLETE AND EXCLUSIVE STATE-

MENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT,

ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MAT-

TER OF THIS AGREEMENT.

Download from Www.Somanuals.com. All Manuals Search And Download.

Beschränkte Benutzerlizenz-Vereinbarung

Das (die) mit diesem Panasonic^®-Produkt (im weiteren als "Produkt" bezeichnet) gelieferte(n) Programm(e) (im weiteren

als "Programme" bezeichnet) wird (werden) nur für den Gebrauch durch den Endnutzer (im weiteren als "der Käufer"

bezeichnet ) lizenziert und darf (dürfen) ausschließlich gemäß den unten aufgeführten Lizenzbedingungen benutzt

werden. Der Gebrauch der Programme durch den Käufer gilt als konkludente Zustimmung des Käufers zu den

Bestimmungen dieser Lizenz.

Die Programme wurden von Matsushita Electric Industrial Co., Ltd. (im weiteren als "MEI" bezeichnet) entwickelt oder

sie wurden auf andere Weise von MEI erworben, und MEI lizenziert die Programme hiermit für den Gebrauch des

Käufers. Der Käufer übernimmt die alleinige Verantwortung dafür, daß die Wahl des Produkts (einschließlich der

zugehörigen Programme) die beabsichtigten Zwecke erfüllt, sowie für die Installation, den Gebrauch und die damit

erzielten Ergebnisse.

Lizenz

Hiermit erteilt MEI dem Käufer das persönliche, nicht übertragbare und nicht ausschließliche Recht und die

Lizenz zur Nutzung der Programme gemäß den Bestimmungen und Bedingungen dieser Vereinbarung. Der

Käufer bestätigt, daß er lediglich eine BESCHRÄNKTE LIZENZ ZUM GEBRAUCH der Programme und der

dazugehörigen Dokumentation erhält und daß mit dieser Lizenz kein Rechtsanspruch, kein Besitzanspruch und

keine anderen Rechte verbunden sind, weder auf die Programme und die dazugehörige Dokumentation, noch

auf die Algorithmen, Konzepte, Ausführungen und ldeen, die von den Programmen und der dazugehörigen

Dokumentation dargestellt werden oder in diese aufgenommen sind, und daß alle Rechte bei MEI verbleiben.

Der Käufer darf die Programme nur mit genau dem Produkt verwenden, zu dessen Lieferumfang die Programme

gehören.

Der Käufer und seine Angestellten und Bevollmächtigten sind zum Schutz der Vertraulichkeit der Programme

verpflichtet. Der Käufer darf die Programme und die dazugehörige Dokumentation ohne vorherige schriftliche

Genehmigung von MEI nicht an Dritte weitergeben oder sie auf andereWeise, einschließlich vonTime-Sharing,

Dritten zugänglich machen.

Der Käufer darf die Programme und die dazugehörige Dokumentation zu keinerlei Zwecken kopieren oder

reproduzieren und darf auch nicht zulassen, daß sie von anderen kopiert oder reproduziert werden, au ßer daß

der Käufer eine (1) Kopie der Programme ausschließlich für Sicherungszwecke und nur zur Unterstützung der

Verwendung der Programme mit genau dem Produkt erstellen darf, zu dessen Lieferumfang die Programme

gehören. Der Käufer darf die Programme weder modifizieren noch solche Modifikationen versuchen.

Der Käufer darf die Programme und eine diesbezügliche Benutzerlizenz nur zusammen mit der Übergabe genau

des Produktes, zu dessen Lieferumfang die Programme gehören, an einen Dritten übergeben. Zur Zeitpunkt

einer solchen Übergabe ist der Käufer verpflichtet, sämtliche von ihm erstellten Kopien, sowohl in gedruckter, als

auch in Maschinensprache abgefaßter Form, jedes einzelnen Programms und der dazugehörigen Dokumentation

an die gleiche Person zu übergeben und alle nicht übergebenen Kopien zu zerstören.

Der Käufer darf kein Copyright,Warenzeichen oder keine andere Bekanntmachung oder Produktkennzeichnung

von den Programmen entfernen und muß jede solche Bekanntmachung oder Produktkennzeichnung auf jeder

Kopie eines der Programme reproduzieren.

Der Käufer darf die Programme und davon erstellten Kopien, weder insgesamt noch teilweise, nicht im Reversierverfahren

assemblieren, kompilieren oder auf mechanischem bzw. elektronischen Wege abtasten.Der Käufer darf die Programme

und deren erstellte Kopien, weder insgesamt noch teilweise benutzen, kopieren, modifizieren, verändern oder

weitergeben, es sei denn dies ist im Rahmen dieser Lizens gestattet.

Falls der Käufer eine Kopie eines der Programme, außer gemäß Absatz E, an Dritte weitergibt, wird diese Lizenz

automatisch außer Kraft gesetzt.

Laufzeit der Lizenz

Diese Lizenz ist nur so lange gültig, wie der Käufer das Produkt zu eigen hat oder im Leasing-Verfahren betreibt, falls

sie nicht vorher widerrufen wird. Der Käufer darf diese Lizenz zu einem beliebigen Zeitpunkt aufheben, indem er die

Programme und die dazugehörige Dokumentation zusammen mit allen davon in jeglicher Form erstellten Kopien auf

eigene Kosten zerstört. Diese Lizenz wird außerdem mit sofortiger Wirkung aufgehoben, wenn eine der oben

aufgeführten Bedingungen eintritt oder der Käufer irgenwelche Bestimmungen oder Bedingungen dieser

Lizenzvereinbarung verletzt. Der Käufer verpflichtet sich, nach einer solchen Aufhebung der Lizenz die Programme

und die dazugehörige Dokumentation zusammen mit allen davon in jeglicher Form erstellten Kopien auf eigene Kosten

zu zerstören.

Der Käufer bestätigt, dieseVereinbarung gelesen und verstanden zu haben, und verpflichtet sich, ihre Bestimmungen

und Bedingungen einzuhalten. Der Käufer bestätigt weiterhin, daß es sich bei der vorliegenden Vereinbarung um

eine vollständige und ausschließliche Aufzeichnung der Vereinbarung zwischen dem Käufer und MEI handelt, die

alle Vorschläge oder früheren Vereinbarungen, in mündlicher oder schriftlicher Form, sowie jegliche Unterredungen

zwischen dem Käufer und MEI in Bezug auf die Gegenstände der vorliegenden Vereinbarung ablöst.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contrat de licence d'usage limité

Le(s) logiciel(s) (les "Logiciels") fournis avec ce produit Panasonic^®(le "Produit") sont exclusivement concédés en

licence à l'utilisateur ultime ("vous"), et ils ne peuvent être utilisés que conformément aux clauses contractuelles ci-

dessous. En utilisant les logiciels, vous vous engagez de manière définitive à respecter les termes, clauses et condi-

tions des présentes.

Matsushita Electric Industrial Co., Ltd.("MEI") a mis au point ou obtenu les Logiciels et vous en concède l'utilisation par

les présentes.Vous assumez l'entière responsabilité du choix de ce Produit (y compris des Logiciels associés) pour

obtenir les résultats escomptés, ainsi que de l'installation, de l'utilisation et des résultats obtenus.

Licence

MEI vous octroie par les présentes le droit et la licence personnels, non cessibles et non exclusifs d'utiliser les

Logiciels conformément aux termes, clauses et conditions de ce Contrat. Vous reconnaissez ne recevoir qu'un

droit limité d'utiliser les Logiciels et la documentation les accompagnant et vous vous engagez à n'obtenir aucun

droit de titre, propriété ni aucun autre droit vis-à-vis des Logiciels et de la documentation les accompagnant ni

vis-à-vis des algorithmes, concepts, dessins, configurations et idées représentés par ou incorporés dans les

Logiciels et la documentation les accompagnant, dont les titres, propriété et droits resteront tous à MEI.

Vous ne pouvez utiliser les Logiciels que sur le Produit unique qui est accompagné par les Logiciels.

Vous et vos employés ou agents êtes requis de protéger la confidentialité des Logiciels. Vous ne pouvez ni

distribuer ni mettre les Logiciels et la documentation les accompagnant à la disposition d'un tiers, par partage de

temps ou de quelque autre manière que ce soit, sans l'autorisation écrite préalable de MEI.

Vous ne pouvez ni copier ni reproduire ni permettre la copie ni la reproduction des Logiciels ni de la documen-

tation les accompagnant pour quelque fin que ce soit, à l'exception d'une (1) copie des Logiciels à des fins de

sauvegarde uniquement pour soutenir votre utilisation des Logiciels sur le Produit unique qui est accompagné

par les Logiciels.Vous ne pouvez ni modifier ni tenter de modifier les Logiciels.

Vous ne pouvez céder les Logiciels et en octroyer la licence à une autre partie qu'en rapport avec votre cession

du Produit unique qui est accompagné par les Logiciels à cette autre partie. Au moment de cette cession, vous

devez céder également toutes les copies, que ce soit sous forme imprimée ou lisible par la machine, de tous les

Logiciels ainsi que de la documentation les accompagnant, à la même partie ou détruire les copies non cédées.

Vous ne pouvez retirer aucune marque de droits d'auteur, marque ou autre ni aucune identification de produit

des Logiciels et vous devez reproduire et inclure toutes ces notices ou identifications de produit sur toutes les

copies des Logiciels.

Vous ne pouvez assembler en sens inverse, compiler en sens inverse ni retracer les Logiciels ni aucune de leurs

copies, de façon électronique ou mécanique, en tout ou en partie.

Vous ne pouvez utiliser, copier, modifier, altérer ni céder les Logiciels ni aucune de leurs copies, en tout ou en partie,

à l'exception de ce qui est expressément stipulé dans ce contrat.

Si vous cédez la possession de toute copie ou de tout Logiciel à une autre partie, à l'exception de ce qui est autorisé

au paragraphe E ci-dessus, votre licence est automatiquement résiliée.

Termes, clauses et conditions

Cette licence n'est effective que pour la durée de possession ou de crédit-bail du Produit, à moins d'une résiliation

antérieure.Vous pouvez résilier cette licence à tout moment en détruisant, à vos frais, les Logiciels et la documenta-

tion les accompagnant avec toutes leurs copies, sous quelque forme que ce soit.Cette licence sera également résiliée,

avec application immédiate, si les conditions de résiliation définies ailleurs dans ce contrat se sont réalisées ou si vous

ne respectez pas les termes, clauses et conditions qui y sont contenues. Au moment de la résiliation, vous acceptez

de détruire, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque

forme que ce soit.

Vous reconnaissez avoir lu ce contrat, en avoir compris toute la substance et avoir accepté de respecter ses termes,

clauses et conditions. Vous reconnaissez en outre qu'ils sont la description complète et exclusive du contrat conclu

entre nous, contrat qui remplace et annule toute proposition ou contrat précédent, écrit ou oral, et toute autre commu-

nication entre nous, relativement à l'objet du présent contrat.

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

AC adapter .................................................................. 6,7,38

AC cord .............................................................................. 6

LED indicators ............................................................. 38,39

Limited use license agreement .......................................... 40

Load default settings ......................................................... 36

Battery indicator .......................................................... 14,29

Battery pack ....................................................... 15,16,38,39

Battery status .................................................................... 14

Brightness adjustment ....................................................... 39

Microphone jack .......................................................... 38,39

Multimedia pocket .................................................. 22,38,39

Network password .............................................................. 9

CD-ROM drive ................................................................. 22

CF-35 series Quick Guide .................................................. 8

CPU .................................................................................. 38

CPU speed change mode .................................................. 13

Clicking ............................................................................ 10

Coffee break password ..................................................... 18

Computer Viruses ............................................................... 5

Conserving power ............................................................. 12

Contrast adjustment .......................................................... 39

Panasonic Setup icon .......................................................... 8

Parallel port ............................................................ 25,38,39

PC Card ............................................................................ 23

PC Card slots .......................................................... 23,38,39

Peripherals ................................................................... 22,31

Port replicator ................................................................... 25

Power indicator ................................................................ 7,9

Power switch ............................................................... 7,9,39

Printer ............................................................................... 25

DC-IN jack ....................................................................... 39

DIAG35 ............................................................................ 28

Display .................................................................... 25,30,39

Displayed colors ............................................................... 38

Double-clicking ................................................................ 10

Dragging ........................................................................... 10

Saving data ......................................................................... 5

Security lock ..................................................................... 39

Security measures ............................................................. 17

Self-diagnosis program ..................................................... 28

Serial port .................................................................... 38,39

Setup utility .................................................................. 31,36

Shutting down ...............................................................10,11

Speakers ....................................................................... 38,39

Standby mode ................................................................... 12

Standby timeout ................................................................ 13

Starting up...................................................................... 9,29

Supervisor password .................................................... 19,20

Supervisor setup ............................................................... 19

Suspend function ..........................................................10,11

Error codes ....................................................................... 28

Expansion bus connector ........................................ 25,38,39

Ext. display port ...................................................... 25,38,39

Ext. keyboard/mouse port ............................................ 38,39

External display ................................................................ 25

FDD cable ......................................................................... 22

Firstaid FD ................................................................ 8,28,32

Floppy disk ................................................................. 5,8,19

Floppy disk drive ......................................................... 22,38

Floppy operation............................................................... 19

Format ............................................................................... 30

RAM module .................................................................... 24

RAM module slot ................................................... 24,38,39

Reinstalling software ........................................................ 32

Reset button ...................................................................... 39

Restarting .......................................................................... 10

TranXit ...................................................................... 6,21,34

Hard disk drive (HDD) ............................................. 5,26,38

HDD motor timeout .......................................................... 13

Headphone jack ........................................................... 38,39

Hibernation function .....................................................10,11

Hibernation timeout .......................................................... 12

User password................................................................... 17

Ventilation hole ................................................................. 39

Volume .............................................................................. 39

I/O port address ................................................................ 31

Infrared communication port .................................. 21,38,39

Infrared data communications .......................................... 21

IRQ ................................................................................... 31

Windows 95 setup.......................................................... 8,35

Write-protect tab ................................................................. 5

LED indicators

.................................................... 38

............................................................................... 14,38

Keyboard ..................................................................... 38,39

^{.............................................................................. 7,9,38}43

Download from Www.Somanuals.com. All Manuals Search And Download.

As an ENERGY STAR Partner, Panasonic has determined that this product

meets the ENERGY STAR guidelines for energy efficiency.

Outline of the International ENERGY STAR Office Equipment Program

The international ENERGY STAR Office Equipment Program is an international program

that promotes energy saving through the use of computers and other office equipment.

The program backs the development and dissemination of products with functions that

effectively reduce energy consumption. It is an open system in which business proprietors

can participate voluntarily. The targeted products are office equipment such as computers,

displays, printers, facsimiles, and copiers. Their standards and logos are uniform among

participating nations.

FJ0597-2117

DFQX2535YA

Printed in Japan

Download from Www.Somanuals.com. All Manuals Search And Download.

Multi Tech Systems Network Card MVP120 User Manual
NEC Network Card NDA 24233 User Manual
Nikon Camcorder d2xmode1 User Manual
NordicTrack Home Gym NTBE01700 User Manual
Northern Industrial Tools Impact Driver 1981202 User Manual
Omnimount TV Mount OM10012 User Manual
Optoma Technology Projector ET700XE User Manual
Panasonic Automobile Parts DVOP001 User Manual
Panasonic Electric Shaver ES726 User Manual
Panasonic VCR AJ HD3700BPE User Manual