Operating Instructions
AC/Rechargeable Professional Hair Clipper
Model No. ER1511
Before operating this unit, please read these instructions completely and save
them for future use.
Download from Www.Somanuals.com. All Manuals Search And Download.
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
• Never tamper with moving parts.
• Avoid grabbing the clipper by the power cord, as it may become detached,
causing damage or injury.
• If the clipper is not working properly, have it inspected at an authorized
service center.
Specifications
Power source: See the name plate on the product.
(Automatic voltage conversion)
Motor voltage: ꢀ.4 V DC
Charging time: 1 hour
Parts identification
mm
6
0/0"
9
mm
0/0"
mm
3
0/0"
12mm
0/0"
mm
4
0/0"
15mm
0/0"
A Main body
1 Trimming height indicator
2 Dial (Height adjustment control)
3 Power switch [0·CHARGE/1]
4 Battery capacity lamp
F 9 mm comb attachment
G 1ꢀ mm comb attachment
H 15 mm comb attachment
I AC adaptor (RE9‑41)
; Power cord
Appliance plug
J Cleaning brush
K Oil
L Charging stand
Charging plug
Socket
M Comb attachment shelves
(×ꢀ)
5 Charge status (
) lamp
6 Appliance socket
B Blade
7 Mounting hook
8 Cleaning lever
9 Moving blade
Stationary blade
C 3 mm comb attachment
D 4 mm comb attachment
E 6 mm comb attachment
N Connectors (×ꢀ)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Charge
Charging the hair clipper
Connect the power cord to the
charging stand.
1
2
Slide the power switch to
“0·CHARGE”.
Plug in the AC adaptor into a
3
household outlet and place the
clipper on the charging stand.
• Charge status (
) lamp glows and charging starts.
• Charging is completed when Charge status (
1 hour later)
) lamp blinks. (Max.
• 1 full charge will provide approximately 70 minutes of continuous
operation.
Connecting the comb attachment shelf to the charging stand
Determine the connection position for the charging
stand and comb attachment shelf. Firmly insert the
connector into the slot at the bottom of the charging
stand.
• If the unit wobbles, then further push in the
connector since it has not been firmly inserted.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
About the LED display
After charging is
completed
10 minutes after
charging is completed
While charging
HIGH
MID
HIGH
MID
HIGH
MID
LOW
LOW
LOW
blinks once every ꢀ
seconds.
• “HIGH/MID/LOW” go
out.
glows.
• “HIGH”, “MID” or
“LOW” blinks.
blinks once every
second.
While using
“HIGH” blinks ‑ The battery capacity is enough.
“MID” blinks ‑ The battery capacity is approx.
60% or less.
“LOW” blinks ‑ The battery capacity is approx.
10% or less.
HIGH
MID
LOW
• Charge the clipper when “LOW” starts to blink.
Charging without the charging stand
1. Slide the power switch to “0·CHARGE”.
2. Plug in the AC adaptor into a household outlet.
3. Insert the appliance plug into the clipper.
AC operation
If you connect the AC adaptor to the clipper in the same way as for charging,
and turn on the power, you can use it even if the battery capacity is low.
• If the clipper does not operate, charge the clipper for approximately
1 minute.
• Be careful not to discharge the battery completely with the power left turned
on. It results in shortening the battery life.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Cut
Using the hair clipper
Turn the dial clockwise or counterclockwise to adjust the moving
blade back and forth to get the desired height. Adjustable in
5 stages from 0.8 mm to ꢀ.0 mm in 0.3 mm steps without
attachments.
The actual cut length may be longer than the set length.
Using the comb attachments
1. Select the trimming heights indicated on the insides
and sides of the attachments.
2 Set the dial to “0.8” and then mount the attachment to
the clipper as illustrated.
0.8
Removing the attachment from the clipper
Remove the attachment as illustrated.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Care
Blade maintenance
Removing and mounting the blade
Removing the blade
1. Hold the clipper with the switch facing
upward and push the blade with your
thumb while catching the blade in your
other hand.
• Be sure to turn off the power before you
remove the blade.
Mounting the blade
1. Set the dial to “2.0”.
2.0
2. Fit the mounting hook into the
blade mounting on the clipper
and push in until it clicks.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the blade
1. Brush off any
hairs from the
clipper and
from around
the blade.
2. Remove the
3. Brush the hairs out from
between the stationary
blade and the moving blade
while pressing down on the
cleaning lever to raise the
moving blade.
blade and brush
off the hairs
from the blade
edge.
Lubrication
1. Apply a few drops of the oil to the
space between the stationary blade
and moving blade.
• Apply the oil to the clipper before and
after each use.
2. Set the dial to “2.0” and then
remount the blade on the clipper.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the built‑in rechargeable batteries
1.Remove the blades 1 and four screws 2.
ꢀ.Remove the spring 3, the under cover 4, and the blade holder 5.
3.Remove the dial 6 and open the housing 7, and then take out two
batteries 8.
• Disconnect the clipper from a household outlet.
• Discharge the batteries completely before removing them.
• Be careful not to short‑circuit the batteries.
WARNING ‑ Do not attempt to replace the batteries for the purpose of
reusing the clipper. This could result in the risk of fire or electric shock.
Important notice regarding environmental protection
The built‑in rechargeable Nickel‑Metal Hydride batteries contain substances
that may be environmentally harmful. Please remove the batteries before
discarding your clipper.
For environmental protection and recycling materials
This clipper contains Nickel‑Metal Hydride batteries.
Please make sure that the batteries are disposed of at an officially assigned
location, if there is one in your country.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Panasonic Electric Works Co., Ltd.
Printed in Japan
ER971015111H Y0710‑0
Download from Www.Somanuals.com. All Manuals Search And Download.
F EN
|