Arbitrator-CP ver.1.9
Basic Operation
[For Officers]
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) Control Reference Guide
Front Camera (AG-CK10P)
Rear panel LED Control
Connector for VPU
Backlight compensation
to make it brighter
T(TELE) for Zoom In
W(WIDE) for Zoom Out
Auto Zoom
Camera Control
REC Start and STOP
*Keep pressing this button for
more than 2 seconds will stop recording.
SUN Shade
REC LED
Lights up in RED
while recording
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) Control Reference Guide
P2 Recorder - VPU (AG-CPD15P)
Key Lock
Locks and unlocks
P2 card
slot cover
the P2 Card slot cover
REC
LED
READY lamp
REC
button button
STOP
P2 card
slot 1, 2
Lights up when
recording is ready
BUSY lamp
Lights up or flashes
while a P2 card is accessed.
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) Control Reference Guide
Control Panel (AG-RCP30P)
1) Lock Lamp
Lock except “REC”, “Menu”,
“Control Panel ON/OFF”,
“Return” Button while lights on
Book
Mark
Auto
Zoom
LCD
Screen
2) Ready Lamp
3) Busy Lamp
Backlight
Compensation
Cursor Button
T: Zoom In
W: Zoom Out
Return
To go back to previous
menu or setting
Menu
REC/STOP
Lamp
Skip
(Back/Forward)
REC
Button
Live/Archive
Switching Button
STOP
Button
Control Panel
ON/OFF
Audio 2 Mute
Button/Lamp
Mute Audio 2 and lamp lights
on by pushing this button.
No recording while muting
(lights on)
IR Mode
(Auto/ON/OFF)
Camera
Select
(Camera1/2))
Volume
Control
Brightness
Control
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) Control Reference Guide
Control Panel (AG-RCP30P) - User Friendly Design
Admin/Archive
Control
Mode Buttons
Live Control
Mode Buttons
1. High Priority Buttons for Live Control Mode on the left side for easy access
High Priority Buttons REC, STOP, Zoom in/out, Bookmark Auto Zoom, Backlight compensation
2. The Same REC/STOP Button Size as that of VPU (P2 Recorder) for easy
recognition
3. Large Button Size and Space between buttons for Users
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) Control Reference Guide
Digital Wireless Microphone TX and RX (TDSS-900-PNA)
Transmitter (TX)
With Receiver (RX)
Transmitter (TX)
Beep Tone
Lavalier Mic
Input
Talk Button:
Press for REC
Built-in Mic
Mute Button
Mode Selection Button
Talk ON : Green LED
BATT : Red-In charging, Green-Fully charged
Regarding Mode and Indication of LED Buttons, there are 3 different versions of TX
as below serial numbers.
Version
Serial Number
Version 1.0
Version 1.5.2
Version 1.5.3
070601609 to 071103658
071103659 to 071104658
071104659 and above
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) Control Reference Guide
Version 1.0: Digital Wireless Microphone TX
Indication of LED BUTTON:
TDSS-900 TX Version 1.0
Serial No: 070601609 to 071103658
Low
Battery
Mode
Talk
REC
Out of
Range
Mute
Push
Push
Off
On
Mode button
Talk button
Mute button
BEEP
Blue
on
Blue
blink
Red Red
Red
on
blink fast off
blink
blink
blink
blink
Vibration
B+V
Blue
off
Blue
off
Red Red
Red
Red
Red
on
blink fast off
Blue
on
Blue
blink
Red Red
on
blink fast off
No
Indication
Blue
off
Blue
off
Red Red
on
blink fast off
1. Goes this mode as initial when Power on.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. After synchronized, the mode goes back to the last.
(1) Control Reference Guide
Version 1.5.2: Digital Wireless Microphone TX
Indication of LED BUTTON:
TDSS-900 TX Version 1.5.2
Serial No: 071103659 to 071104658
Mode
Talk
REC
Low
Battery
Out of range
Mute Button
Push
Push
OFF
ON
Mode button
Talk button
Mode 1
BEEP
Blue
Blue
ON
Blue
Blue LED OFF
Blue LED
OFF
OFF
Blink Fast
Blue OFF
Blink Slow
Beep ON
Mode 2
Vibration
Blue
OFF
Blue
OFF
Blue LED OFF
Vibr ON
Blue LED
OFF
OFF
Mode 3
B+V
Blue
OFF
Blue
ON
Blue
Blue LED OFF
B+V ON
Blue LED
OFF
Blink Fast
Blink Slow
Mode 4
No Indication
Blue
OFF
Blue
OFF
BLUE
OFF
BLUE
OFF
Blue LED OFF
1. Blink 2 time and then LED OFF: this mode as initial when Power on.
2. After synchronized, the mode goes back to the last.
3. When TX is Off and inserted to RX, there will be no synchronized.
4. RED LED is not available any mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) Control Reference Guide
Version 1.5.3: Digital Wireless Microphone TX
Indication of LED BUTTON:
TDSS-900 TX Version 1.5.3
Serial No: 071104659 and above
Low
Battery
Mode
Talk
REC
Out of
range
Mute
Push
Push
Off
On
Mode
button
Mode button
Talk button
Talk button
Mute button
Vibration Blue
on
Blue
blink
Red
on
Red
Red
off
Red/Blue Blink
(Mute/Talk button)
Blink
No
Vibration
Blue
off
Blue
off
Red
off
Red
off
Red
off
1. LED ON: this mode as initial when Power on
2. After synchronized, the mode goes back to the last.
3. When TX is Off and inserted to RX, there will be no synchronized.
Download from Www.Somanuals.com. All Manuals Search And Download.
(2-a) Control Panel Menu for Officer
[Camera] For users who do not use LPR (License Plate Recognition mode)
[Top Menu]
(“Init LPR Mode” in Admin set up is “Disable” as a factory default.)
*For LPR users, please go to ”Camera Menu for LPR” for details
Re-Auto Focusing
Adjust manual focus
Adjust image brightness
[Audio]
1. “IN CAR” for In car Mic (Mic in)
2. “WMIC” for 2nd Wireless Mic (Audio 2 in)
3. “LINKCAM” to change the Audio 1 or 2
by linking with the camera changes,
*Audio 1 for Wireless Mic 1 (Audio 1 in)
Check Audio
[Restore]
When appeared
in
[Archive]
Playback the recorded video
Control Panel OSD, execute
“Restore”
[Setup/Info]
On Screen Type for Control Panel
“Auto”, “SIMPLE”, “DETAILS” or “OFF”
Camera LED (Camera Tally Light),
for “ON” or “OFF”
Download from Www.Somanuals.com. All Manuals Search And Download.
(2-b) Camera Menu for LPR (License Plate Recognition)
In order to use LPR (License Plate Recognition) mode, the Administrator needs to set up
“Init LPR Mode” as “Enable” in Admin/Camera menu.
*If setting up “Init LPR Mode” as “Disable”, there will be no “LPR Mode”, “LPR/Patrol Shutter Speed”, “LPR/Patrol Zoom” on screen as shown
below. (Just “Auto Focus”, “Manual Focus” or “AE” can be selectable and changed in “Camera” menu.)
[Camera]
1) [LPR Mode] is set to “LPR”
[Top Menu] while recording is
being stopped in the live screen
2) [LPR Mode] is set to “PATROL”
“LPR” for LPR ON
“Patrol” for LPR OFF
Select “Auto”,
“1/500”, or “1/1000”
Select “Auto”, “1/100”
“1/500”, or “1/1000”
Set x1.0 to x22.0
LPR ON
LPR OFF
[Top Menu] while the live screen
is being recorded
[Camera]
1) [LPR Mode] is set to “LPR”
2) [LPR Mode] is set to “PATROL”
Download from Www.Somanuals.com. All Manuals Search And Download.
(3) Record the video (Live Mode)
Press REC button for (1) Control Panel, (2) Camera (Rear Panel), or (3) VPU (P2 Recorder)
*If the trigger is set, VPU will start recording automatically when the trigger is on.
<Camera>
<Control Panel>
<VPU-P2 Recorder>
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) Playback the recorded video (Archive Mode)
(a) Press “Live/Archive” button of Control Panel to playback the video.
(Playback starts from the location where playback was last made. Or if the recording was started or stopped
prior to pressing “Live/Archive” button, playback starts from the beginning of the file.)
Or
(b) Press “Menu” of Control Panel and go to “Archive”.
(b)
(a)
[Live mode]
[Archive mode]
Download from Www.Somanuals.com. All Manuals Search And Download.
(5) Camera Control
(a) Zoom
“W”: Zoom Out
“T”: Zoom In
(b) Auto Zoom
Press “Auto Zoom” button of Control Panel or Camera.
(c) IR Mode
Press “IR Mode” button switching to IR “Auto”, “On”, “Off”
Auto Zoom
W: Zoom Out
T: Zoom In
IR Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
(6) Officer Information
Register at the beginning of shift & delete at the end of shift
(A) Register the Officers information (At the beginning of shift)
(1) “Auto”:
(2) “Manual”:
Plug USB memory (saved the officer information) to VPU.
Plug USB memory to VPU and press “Load” button.
If 2 officers need to be loaded, plug 2 different USB memories to VPU.
Press “Select” button in “Officer” by Control Panel menu.
(3) “List”:
(B) Delete the Officer information (At the end of shift)
“Manual”, “List”: Press “Delete” button in “Officer” by Control Panel menu.
[Manual]
[Top Menu]
-while REC stopped-
Register
Officers
[List]
Delete
Officers
Download from Www.Somanuals.com. All Manuals Search And Download.
Arbitrator-CP ver.1.9
Basic Set up & Operation
[For Administrators]
Download from Www.Somanuals.com. All Manuals Search And Download.
Arbitrator-CP Basic Set up & Operation for Administrator
-Contents-
(1) -Before Use, Format 16GB P2 Card
-16GB P2 Card Format by Products / Combination with Windows version
(2) Control Panel Menu for Administrator
(3) REC/Play Set up by Administrator
(4) Camera Control - Auto Zoom / IR Set up by Administrator
(5) Control Panel Key Lock
(6) On Screen Type set up by Officer / OSD set up by Administrator
(6-a) Live Mode On Screen Type
(6-b) Archive Mode On Screen Type
(7) Trigger
(a) Set up by Administrator
(b) Stop recording by Trigger OFF
(8) Menu (VPU Setting) Copy
(9) Event Type for Bookmark
(a) Create an Event Type text and register it to VPU
(b) How to Add / Delete the Bookmark?
(10) Officer/Admin Information Set up
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) Before use, Format 16G P2 card
zFormatting 16G P2 card is mandatory at the first time usage.
zWhen modified (copy, delete, move etc) folders in P2 Card, please format the card.
(If you copy the folders/files from 5 slot P2 drive or PC PCMCIA to PC HDD, please format the card.)
zThe format of 16G P2 card is available by Control Panel, 5 slot P2 drive and PC PCMCIA slot.
zNote that 16GB P2 card limit the number of files that can be recorded per below chart.
# of
# of maximum recording files per day
recording days
With Bookmark
Without Bookmark
62 days
340 files
508 files
<How to format 16GB P2 card by Control Panel?>
•
•
•
Insert new 16GB P2 cards to P2 Recorder (VPU)
By Control Panel Menu, go to “Setup/Info”, “Admin (page 2/2)”, “File Management” and select “Format”
Press “Format” when “Format all P2 cards!!!” message is appeared.
Then, you will see “All cards are formatted” message when the format is completed.
[File Management]
[Setup/Info]
[Admin] Page 2/2
[Top Menu]
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) 16GB P2 Card Format by Products /
Combination with Windows version
Format by
How to format?
SI
By SI Menu, go to “Config”-”Operations”-”Format”.
(FE Application)
Control Panel
By Control Panel Menu, go to “Setup Info”-”Admin”-”File Management”-
”Format”
Before format, install the P2 driver (from “P2 ICV Filter w/ P2 Drivers” CD included in
Arbitrator kit) to PC. Then, select the removable disc drive in PC that inserted P2 card.
Right click on that drive and select “format”
PC PCMCIA slot
(Windows)
Before format, install the P2 driver (from “P2 ICV Filter w/ P2 Drivers” CD included in
Arbitrator kit) to PC. Then, select the removable disc drive in PC that inserted P2 card.
Right click on that drive and select “format”
5 slot P2 Drive
(AJ-PCD20P)
Before format, Install the P2 driver (from “P2 ICV Filter w/ P2 Drivers” CD included in
Arbitrator kit) to PC. Then, press “Format P2C” button on the unit
P2 Store
（AJ-PCS060G)
Vista
XP
2000
Server
2003
SP2
SP4 + Hot Fix*
PCMCIA slot (Card Bus) in PC
Y
Y
Y
Y
N
Y
N
N
5 slot P2 Drive (AJ-PCD20P)
through USB
5 slot P2 Drive (AJ-PCD20P)
though IEEE1394
Y
Y
Y
Y
N
Y
N
N
P2 Store (AJ-PCS060G)
through USB
Download from Www.Somanuals.com. All Manuals Search And Download.
*For the users who need Win2000 Hot Fix, please contact 1-800-LAPTOP5 (1-800-527-8675) to obtain it.
(2) Control Panel Menu for Administrator
[Setup/Info]
[Top Menu]
[Admin] Page 1/2
[Admin] Page 2/2
Record/Play mode settings
Date and Time settings
Export or Delete files
Format files
Officer Registration
Trigger (8GPIO) settings
On Screen Display settings
to appear on screen and
include in recording files
Camera settings
Management mode
For Officer Registration
(Auto, Manual, List)
Download from Www.Somanuals.com. All Manuals Search And Download.
(3) REC/Play Set up by Administrator
Power off time setting after shutting down the ignition
Initial camera setting, camera 1 or 2
Initial Audio 2 setting, INCAR or 2nd WMIC or LINK CAM
Start recording when VPU is turned on
Setting: Off Fixed
[Admin] Page 1/2
From Control Panel Top Menu
--”Setup info”—”Admin”
1 fps (frame per sec) recording
Recording mode: F-2Mbps (720x480, 30fps)
F-1Mbps (720x480, 10fps), Q-1Mbps (320x240, 30fps)
Q-512kbps (320x240, 30fps)
Recording will continue up to 1,2,5,10,15,20,30, 60, 90,
or Continue even if pressing STOP button
Set Pre Rec and Post Rec Time (0 to 90 seconds)
Set rule of file name, world time (WT) or local time (LT)
Select On Screen Display, “Simple”, “Details”, “Last”
or “Off”
Enable or disable output of recording status as GPIO9
Enable or disable output of recording Error status as GPIO9
Select the initial audio output upon power on.
(Off, 1, 2, Both, Last)
Select “Single” (normal playback, one file at a time) or
“Relay” (multiple files playback)
Playback jumps to the trigger or bookmark position,
whichever found earlier
Move to the beginning of a file during playback
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) Camera Control-Auto Zoom / IR Set up by Administrator
[Admin] Page 1/2
From Control Panel Top Menu
--”Setup info”—”Admin”
Adjust “Zoom Limit”, “x22” for optical
or “x220” for digital
1. Adjust “Auto Zoom Magnification”
selecting from “1,2,3,4,5,7,10,15, or 22”
2. Adjust “Auto Zoom” Time for zoom magnification
retention time from “3,5, or 8” seconds
*Factory Initial setting:
“Zoom Limit” = “x22”
“Auto Zoom Magnification” = “10”
“Auto Zoom Time” = “3” seconds.
Select “Auto”, “Off”, “On” or “Last”
When setting “Init IR Mode” as “Auto”,
select IR Level, “Low”, or “High”
and IR Time, “10, 30, 60 or 300”
Select “Auto”, “Preset”, or “Disable”.
“Auto”: Set to auto focus when zoom ratio is changed.
“Preset”: When the soom is 3x or below, the camera
is focused at about 15m (50ft).
“Disable”: Focus is locked at a distance of about 40m
(130ft) and auto focus is disabled.
Enable or disable LPR (License Plate Recognition)
Download from Www.Somanuals.com. All Manuals Search And Download.
(5) Control Panel Key Lock
All buttons except buttons in circle
“REC”
“Cursor Button” “Menu” “Return”
“Control Panel On/Off”,
“REC” on both VPU and Camera
will be locked.
Control Panel Key Lock Set up by Administrator and Officer
[Key Lock by Admin]
From Control Panel Top Menu
--”Setup info”—”Admin”
Select “Operation Key Lock”,
“On” or “Off”.
[Key Lock by Officer]
From Control Panel Top Menu
**When locked by Administrator,
--”Setup info”—”Officer”
the key cannot be unlocked
by Officer (from “Officer” Set up).
Download from Www.Somanuals.com. All Manuals Search And Download.
(6) On Screen Type set up by Officer
/ OSD set up by Administrator
[Top Menu]
[Setup/Info]
On Screen Type set up by Officer,
“AUTO”, “SIMPLE”, “DETAILS” or “OFF”
*1. See more details on “Live mode on screen type” and “Archive
mode on screen type”.
*2. On Screen Type will NOT be recorded in the recording file.
“Printable (A to Z)” of the
trigger will be recorded
in the recorded file when
turning on the trigger.
[Admin] Page 1/2
“Vehicle ID @ Area” will be recorded in the recorded file when
turning on “V-ID/Area”.
*1. Vehicle ID and Area need to be included in the Officer registration text file.
*2. The first 5 letters for Vehicle ID and the first 4 letters for Area will be
appeared on screen. For example, if Vehicle ID is “1234567” and Area is
“California”, it will be “12345@Cali” appeared on screen.
OSD (On Screen Display) for the date/time,
trigger and V-ID/Area set up by Administrator
will be included in the recorded file.
**If On Screen Type “DETAILS” is set up, this OSD will be hidden.
Download from Www.Somanuals.com. All Manuals Search And Download.
(6-a) Live Mode On Screen Type
[SIMPLE]
(1) Remaining P2 card recording time
(1)
(2) Mode indication ( Pause,
Record)
(2)
(3)
(4)
(3) Status Display
PON: Power On Recording “ON”
CARD FULL: No space on P2 card
CARD PROTECT: The write-protect switch of P2 card is set to protect
VUP CARD: Recording is not possible due to P2 card intended for
version upgrade
UNFORMATTED: P2 card is not formatted
REFORMAT: P2 card needs to be reformatted
ILLEGAL CARD: An unusable card is inserted in VPU
NO CARD: No P2 card is inserted in VPU
(5)
(6)
(7)
RUNDOWN: P2 card is closed to the end of its service life
(4) Remaining P2 Card capacity bar
[DETAILS]
(5) “Restore” appears only when there is a file that needs to be restored
(1)
(8)
(9)
(10)
(6) Mark Position
Bookmark position
(2)
(3)
(4)
(7)
VPU set up Status
C1: Camera 1 selected
IR: Camera IR mode is “ON”
C2: Camera 2 selected
IRA: Camera IR mode is “OFF”
BL: Camera backlight is “ON” TAL: Camera lamp is “ON”
LOCK: Control Panel Key Lock is “ON”
(8) Speed (MPH/KPH): OWN-own vehicle speed, TGT-target vehicle speed
*Target vehicle speed depends on the type of radar gun that is connected
(11)
(12)
(5)
(6)
(7)
(9) Location information (latitude)
(10) Location information (longitude)
(11) Date/Time
*If setting on screen type “AUTO” and (1), (2) or (3)
is changed, “SIMPLE” on screen type will be
appeared on screen for 3 to 5 seconds.
(12) Trigger input status: GPIO 1 to 8 are displayed in order from the left.
Download from Www.Somanuals.com. All Manuals Search And Download.
The letters assigned by “Printable” appear when the “Detection” occurs
(6-b) Archive Mode On Screen Type
[SIMPLE]
(1)
(3)
(2)
(1) Playback filename (Local time at start of recording)
(2) Mode indication ( Playback, Pause, FF
(4)
RW
Slow)
(3) Playback Speed and Status Display
<Playback Speed> x1/10, x1/2, x4, x20, x200
<Status Display>
READ ERROR: An error occurred while reading
META ERROR: No associated meta information file exists.
PLAY ERROR: A decoder malfunction occurred
(5)
(6)
(7)
(4) Playback location
(5) “Restore” appears only when there is a file that needs to be restored
[DETAILS]
(6) Mark Position
Bookmark position
Trigger position
File beginning
(8)
(9)
(1)
(7) Sound output setting: A1-Audio 1 A2-Audio 2
(2)
(3)
(4)
(10)
(8) Speed (MPH/KPH): OWN-own vehicle speed, TGT-target vehicle speed
*Target vehicle speed depends on the type of radar gun that is connected
(9) Location information (latitude)
(10) Location information (longitude)
(11) Date/Time
(11)
(12)
(5)
(6)
(7)
(12) Trigger input status: GPIO 1 to 8 are displayed in order from the left.
The letters assigned by “Printable” appear only when the “Detection” occurs.
*If setting on screen type “AUTO” and (2) or (3)
is changed, “SIMPLE” on screen type will be
Download from Www.Somanuals.com. All Manuals Search And Download.
appeared on screen for 3 to 5 seconds.
(7) Trigger
(a) Set up by Administrator
(1) Go to “Trigger” in “Admin” menu by Control Panel.
(2) Select “Action” which you need when detecting the trigger signal (Trigger 1 to 8).
Select the Detection from the followings and
choice of detection depends on “Action”:
Trigger On or Off setting
1. In “REC”, “CAM1REC”, “CAM2REC” at Action,
Select the detection from “H”, “Level H”, “L”, “Level L”, “B”.
2. In “CAM1”, “CAM2”, “CAM1LED”, “AUTOZOOM”, “STOP”,
Select the detection from “H”, “L”, “B”.
Select “Action” from the followings
for the detection of trigger signals
“REC”
3. In “None”, select the detection from “H”, “L”,
“SPEED” (Trigger 8 only)
“STOP”
“AUTOZOOM”
“CAM1”
“CAM2”
“CAM1REC”
“CAM2REC”
“CAM1LED”: Change ON/OFF of
REC lamp on the Front Camera
(AG-CK10P)
Assign the characters to be used in the OSD display.
*When SPEED is selected at the trigger, “Printable”
becomes ”-” and cannot be modified. No OSD is displayed.
“NONE”: No operation
Download from Www.Somanuals.com. All Manuals Search And Download.
(7) Trigger
(b) Stop recording by Trigger OFF
[Admin]
From Control Panel Top Menu
--”Setup info”—”Admin”
REC Continue
Timer Setting
Select either of
“Continue” or “1-90”
Trigger
Setting
Select either of “Level H”, “Level L”
to stop recording by Trigger OFF
Stop Recording
by Trigger OFF
Detection
REC Continue Time
(Timer Setting)
Stop Recording Priority
(Level Signal Setting)
Yes
Yes
No
1) “STOP” button is pressed.
2) Trigger OFF
(Level H or Level L)
(“Continue”)
ex. Level H
Yes
1) “STOP” button is pressed.
2) Trigger OFF
(“1 – 90”)
3) “REC Continue Time”
STOP REC STOP
No
No
No
“STOP” button is pressed.
(H, L, No, or B)
(“Continue”)
Yes
1) “STOP” button is pressed.
2) “REC Continue Time”
(“1 – 90”)
[Remark] 1. If setting up more than 2 triggers as Level Signal, start recording when the 1st trigger is turned on and
stop recording when all triggers set up as Level Signal are turned off.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Minimum recording time is 1 minute when setting up the trigger as Level Signal.
(8) Menu (VPU settings) Copy
[Step 1] Get a setting configuration file from the VPU which settings need to
be copied to other VPUs.
(1) Plug an USB memory* to the VPU which settings need to be copied to other VPUs.
(2) Go to “Operations” in “Admin” menu by Control Panel and select “Menu Copy”.
(3) Press “Copy” button if you agree to copy menu settings to the USB memory.
*This action creates a setting configuration file in the USB memory. Please use the USB memory to get the setting
configuration file because even if inserting a P2 card instead to the VPU, it cannot be created in the P2 card.
[Step 2] Copy the settings to the 2nd VPU.
(1) Plug the USB memory stored a setting configuration file at [Step 1] to the 2nd VPU.
(2) Leaving the P2 card slot cover open, press and hold the REC button on the 2nd VPU
(2)
until the “Ready” or “Busy” lamp starts to flash (about 10 seconds or more).
Keep pressing
REC button
(3) “Ready” light will flash and “Busy” lamp will light. Press the “Stop”
button on VPU when the “Rec” light starts flashing.
(4) After pressing “Stop” button, the 2nd VPU will reboot and can see
the same menu setting as the VPU of [Step 1].
Download from Www.Somanuals.com. All Manuals Search And Download.
(9) Event Type for Bookmark
(a) Create an Event Type text and register it to VPU
[STEP 1: Create the Event Type text file (“evtype.txt”) and save it to the USB memory.]
Create the event
type text file
“evtype.txt”
under “WIDKEY”
Create “WIDKEY”
under root directory
by PC.
Plug an USB
memory to PC
<Event Type text file example>
EvType1=Criminal Arrest
EvType2=Traffic Stop
EvType3=DUI
●
●
●
Up to 99 letters
for each type,
Max 10 event type
in the “evtype.txt”
USB Memory
EvType10=Drinking Check
[STEP 2: Register the Event Type for the Bookmark to VPU.]
(a) Plug the USB memory stored the event type file “evtype.txt” to VPU.
(b) Go to “Registration” in “Admin” menu by Control Panel and select “Load Event Type”.
Plug the USB
memory stored
“evtype.txt”
to VPU
REMARK: How to delete the Event Type?
Create the Blank Event Type text file (saved as “evtype.text”) and save it to the USB memory as STEP 1.
Then, please follow the same procedure as like STEP 2 to load the Blank Event Type text file.
Download from Www.Somanuals.com. All Manuals Search And Download.
(9) Event Type for Bookmark
(b) How to Add / Delete the Bookmark?
LIVE mode
(during recording)
ARCHIVE mode
(during playback)
Event Type
Loaded to VPU
YES
NO
YES
Press “Bookmark” button.
NO
Add the
bookmark
Press “Bookmark” button.
will appear on screen.
Press “Bookmark” button.
will appear.
will appear and select the event type.
Delete the
bookmark
N/A
Press “Bookmark” button while
appears.
Press “Bookmark” button
while
appears.
will appear and select the
to delete the bookmark.
“DEL”
<How to Add the Bookmark?>
<How to Delete the Bookmark?>
In case the event types are loaded,
(1) Press the Bookmark button while the Event type pop up appears.
(2) Select “DEL” in the Event Type pop up by “◄ ►” button.
In case the event types are loaded
(1) Press the bookmark button at Archive mode*.
(2) Event type pop up will appear and select an event type
by “◄ ►” button.
(3) Press the “Bookmark”, “Return” or “Menu” button to confirm the entry.
(3) Press the “Bookmark”, “Return” or “Menu” button
to confirm the entry.
(1)
(2)
(1)
(2)
In case no event types are loaded,
Press the “Bookmark” button when a bookmark icon
appears at Archive mode during playback, pause or slow playback.
In case no event types are loaded
(1) Press the “Bookmark” button at Live or Archive mode.
*Event type will appear on screen only at Archive mode.
(2) A Bookmark icon
will appear on screen.
At live mode, the bookmark icon
by pressing “Bookmark” button
appears on screen
Download from Www.Somanuals.com. All Manuals Search And Download.
(10) Officer/Admin Information Set up
-Contents-
1. Admin Set up (1) Creating Text Files and Saving in USB memory
2. Admin Set up (2) Text Files for Officer/Admin
3. Admin Set up (3) How to register Officer/Admin information?
4. Admin Set up (4) How to log in “Admin” menu?
5. Admin Set up (5) How to delete Admin/Officer information?
6. Officer Set up (1) How to register Officers info at the beginning of shift?
7. Officer Set up (2) How to delete Officers info at the end of shift?
Download from Www.Somanuals.com. All Manuals Search And Download.
-Officer/Admin Information Set up by Control Panel-
Admin Set up (1) Creating Text Files and Saving in USB memory
Create the following text files under
Plug USB
USB
Memory
“WIDKEY” directory:
memory
to PC
(1) Officer Data File
(2) Officer Registration File
(3) Administrator Registration File
(4) Event Type File
(see “Event Type for Bookmark”)
Create “WIDKEY”
under root directory
By PC
(1) Officer Data File:
“wid*****.txt “
(Up to 8 characters
for file name,
1 text file per officer,
Max 2 text files)
(3) Administrator
Registration File
“wadmin.txt”
（Max. 10 Administrators)
(2) Officer Registration File “wofficer.txt”
（Max. 500 Officers)
**Necessary only when using “Officer List” mode
(4) Event Type File “evtype.txt” For Bookmark
(See “Event Type for Bookmark)
(Up to 99 characters for each type,
Max 10 event types in the “evtype.txt”)
Download from Www.Somanuals.com. All Manuals Search And Download.
-Officer/Admin Information Set up by Control Panel-
Admin Set up (2) Text Files for Officer/Admin
(1) Officer Data File: “wid*****.txt “
(2) Officer Registration File:
(3) Administrator Registration
*Within 8 characters for file name,
1 text file per officer, Max 2 text files
“wofficer.txt”
File: “wadmin.txt”
*Max 500 officers in 1 text file
*Necessary only when using “Officer List” mode
*Shift time, shift, area and source will NOT be
registered.
*Max 10 Administrator in 1 text file
Ex. File “widtest1.txt”
# Sponge Bob
# James Bond
FirstName=James
Middle Name=
LastName=Bond
ID=ICV007
FirstName=Sponge
MiddleName=
LastName=Bob
ID=ICV12345
Password=Pana1
SDate=2007-09-13
STime=9:00
# Ichiro Suzuki
FirstName=Ichiro
MiddleName=
LastName=Suzuki
ID=ICV51
Password=007
Border=----------------------
# Jimmy Harris
Border=------------------------------------
Edate=2007-09-13
ETime=17:00
# David Ortiz
FirstName=David
MiddleName=
LastName=Ortiz
ID=ICV34
Shift=DUI
Area=District1
Source=54321
FirstName=Jimmy
Middle Name=
LastName=Harris
ID=ICV010
Ex. File “widtest2.txt”
# Patrick Star
Password=010
Border=------------------------------------
Border=----------------------
# Mike Cowen
# Derek Jeter
FirstName=Derek
LastName=Jeter
ID=ICV2
FirstName=Patrick
MiddleName=
LastName=Star
ID=ICV54321
Password=Pana2
SDate=2007-09-14
STime=08:15
Edate=2007-09-14
ETime=18:00
FirstName=Mike
Middle Name=
LastName=Cowen
ID=ICV020
Border=------------------------------------
Password=020
# Joe Mauer
FirstName=Joe
LastName=Mauer
ID=ICV7
Shift=Traffic
Area=District2
Source=10000
Download from Www.Somanuals.com. All Manuals Search And Download.
-Officer/Admin Information Set up by Control Panel-
Admin Set up (3) How to register Officer/Admin information
(A) Before registering the Officers, Administrator needs to set “Management Mode” in “Admin ” menu
such as “Auto”, “Manual” or “List” for Officer registration mode. (See “Officer Set up (1)”)
[Admin]
[Setup/Info]
[Top Menu]
[Management Mode]
(A)
(B)
Select “Auto”, “Manual” or “List”
(See “Officer Set up (1)”
[Registration]
(B) How to register Officer/Admin
Information to VPU by Control Panel?
1. Plug USB memory saved Officer
Registration File (“wofficer.txt”)
“Setup/Admin”
and Admin Registration File**
(wadmin.txt) to VPU
2. Go to “Registration” in “Admin” menu
Load Admin:
Load Officer:
Load Max 500 Officers from a USB memory
saved “Officer Registration File” to VPU
Load Max 10 Administrators from a USB
memory saved “Administrator Registration
File” to VPU
List Officer:
View Max 500 Officer name and ID that
had already registered in VPU.
List Admin:
View Max 10 Administrator name & ID that
had already registered in VPU
**Necessary only when using “Officer List”
mode
Download from Www.Somanuals.com. All Manuals Search And Download.
-Officer/Admin Information Set up by Control Panel-
Admin Set up (4) How to Log in “Admin” menu?
How to Log in “Setup/Admin” menu by administrator?
(1) Create Officer Data File (wid*****.txt) that is the same Admin information registered in VPU
(2) Save the Officer Data File to USB memory and plug it to VPU to log in “Setup/Admin” menu
NOTE1: If many officer data files are existing in USB memory, VPU will detect the first one in ascending order.
NOTE2: If wrong USB memory plug to VPU, the error message will appear.
“wadmin.txt”
“widtest3.txt”
registered in VPU
(same info as “wadmin.txt”)
# James Bond
# James Bond
[Admin]
FirstName=James
FirstName=James
Middle Name=
Middle Name=
LastName=Bond
LastName=Bond
ID=ICV007
ID=ICV007
Password=007
Password=007
SDate=2007-10-01
STime=9:00
Edate=2007-10-01
ETime=17:00
Right USB memory
Plug to VPU
[Top Menu]
[Setup/Info]
(different info from
“wadmin.txt”)
[Error Message]
Wrong USB memory
Plug to VPU
# Sean Connery
FirstName=Sean
Middle Name=
LastName=Connery
ID=ICV777
Password=1234
SDate=2007-10-01
STime=9:00
Edate=2007-10-01
Download from Www.Somanuals.com. All Manuals Search And Download.
ETime=17:00
-Officer/Admin Information Set up by Control Panel-
Admin Set up (5) How to delete Admin/Officer information?
How to delete Admin information when Admin information had registered in VPU?
(1) Log in “Admin” menu followed by Admin Set up (4)
(2) Create a blank Admin Registration File (wadmin.txt) and save it to USB memory. Then, plug USB
memory to VPU and select “Load Admin” in Admin menu (see Admin Set up (4))
Blank Admin
Registration File:
“wadmin.txt”
# James Bond
FirstName=James
Middle Name=
LastName=Bond
ID=ICV007
#
FirstName=
Middle Name=
LastName=
ID=
Password=007
Password=
Plug into VPU for delete
Blank Officer
Data File:
“wofficer.txt”
#
FirstName=
Middle Name=
LastName=
ID=
How to delete Officer information when Admin information had registered in VPU?
(1) Log in “Admin” menu followed by Admin Set up (4)
(2) Create a blank Officer Data File (wofficer.txt) and save it to USB memory. Then, plug USB
memory to VPU and select “Load Officer” in Admin menu (see Admin Set up (4))
Download from Www.Somanuals.com. All Manuals Search And Download.
-Officer/Admin Information Set up by Control Panel-
Officer Set up (1) How to register Officers info at the beginning of shift?
How to register the Officers information at the beginning of the shift?
(1) Plug USB memory saved the Officer information as the file “wid*****.txt”
(2) Go to “Officer” by Control Panel menu and Officer Data will be registered according to the
“Management Mode” set up by Administrator
NOTE1: ”Management Mode” in “Admin” menu needs to be set as “Auto”, “Manual” or “List” by Administrator
(See “Admin Set up (2)”)
NOTE2: “Auto” will be loaded the first 2 files in ascending order if there exists some files in USB memory.
“Manual” will be loaded the first file only in ascending order. If there are 2 officers to load, it’s necessary to have 2 USB
memories.
Officer Info Registration according to “Management Mode”
[Auto]
[Manual]
[Top Menu]
[Setup/Info]
“MANUAL” mode is to be used
when Officer 1 and 2 data needs to
be loaded by 2 different USB
memories
“AUTO” mode is to loads the
max 2 Officer Data Files from
a USB memory automatically
[List]
“LIST” mode is to list and select
the officer data that had already
Download from Www.Somanuals.com. All Manuals Search And Download.
registered in VPU.
-Officer/Admin Information Set up by Control Panel-
Officer Set up (2) How to delete Officers info at the end of shift?
How to delete Officers information at the end of the shift?
(1) Go to “Officer” by Control Panel menu. If either “Manual” or “List” in “Management Mode”
is set by Administrator, delete it at “Officer”
(2) Please overwrite the next one or two officers by USB memory saved Officer Data File
(wid*****.txt) when “Auto” in “Management Mode” is set since it is impossible to delete
“Officer”.
Officer Info Delete according to “Management Mode”
[Manual]
[List]
[Top Menu]
(1)
[Setup/Info]
Due to No delete for Officer Info at “Auto” in “Management Mode”,
please overwrite the next Officers information by Officer Data File
(2)
“wid*****.txt”
[Auto]
# James Bond
FirstName=James
Middle Name=
LastName=Bond
ID=ICV007
Password=007
SDate=2007-10-01
STime=9:00
Edate=2007-10-01
ETime=17:00
Shift=Traffic
Plug in
Area=District 5
Source=5555
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX: Officer/Admin Information Text File Comparison
-Data of text files for Officer/Admin-
Officer Data File
“wid*****.txt”
Officer Registration File
“wofficer.txt”
Administrator Registration
File: “wadmin.txt”
1) Up to 8 characters
for file name
1) Max 500 officers in 1 text file 1) Max 10 Administrator
Remark/Limitation
2) Necessary only when using
“Officer List” mode
in 1 text file
2) 1 text file per officer,
Max 2 text files
2) Shift time, shift, area and
source will NOT be registered
3) Shift time, shift, area and
source will NOT be registered.
Data to loaded
to VPU
Max
Characters
First Name
Middle Name
Last Name
ID
50
1
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
50
50
12
10
5
Password
SDate
STime
EDate
10
5
ETime
Shift
10
10
50
Area
Source
Download from Www.Somanuals.com. All Manuals Search And Download.
Y: Data that can be loaded to VPU
N: Data that can NOT be loaded to VPU
|