In-dash 7 Widescreen Color LCD Monitor
CY-VM7203W
Operating Instructions
Please read these instructions carefully before using this product and keep this manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
(continued)
Caution
Caution
Caution
3
4
Deeper installation method for fixing the mounting
spring is not available in some types of cars.
When bending the mounting tab of the mounting
collar with a screwdriver, be careful not to injure
your hands and fingers.
Ware gloves for safety. Make sure that wiring is
completed before installation.
To prevent damage to the unit, do not connect
the power connector until the whole wiring is
completed.
Observe the following cautions when using this
unit.
Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road
and traffic conditions while driving.
Do not insert or allow your hand or fingers to be
caught in the unit.
To prevent injury, do not get your hand or fingers
caught in moving parts. Especially watch out for
infants.
This unit is designed for use exclusively in
automobiles.
Do not operate the unit for a prolonged period with
the engine turned off.
Operating the audio system for a long period of time
with the engine turned off will drain the battery.
Do not expose the unit to direct sunlight or
excessive heat.
Otherwise these will raise the interior temperature
of the unit, and it may lead to smoke, fire, or other
damage to the unit.
Do not use the product where it will be exposed to
water, moisture, or dust.
Exposure of the unit to water, moisture, or dust may
lead to smoke, fire, or other damage to the unit. Make
especially sure that the unit does not get wet in car
washes or on rainy days.
Record your registered ID code and keep it in a
secure location. (Fill in the ID code memo. (page 9))
If you forget it, you will be unable to use the unit.
In case you forget the ID code, please consult your
nearest Panasonic Service Center.
Be sure to select OFF when your car has no ACC
position in the ignition switch. Failure to do this
could cause the battery to go dead.
Observe the following cautions when installing.
If your car is equipped with air bag and/or anti-
theft systems specific procedures may be required
for connection and disconnection of the battery to
install this product.
FAILURE TO FOLLOW THE PROCEDURE MAY
RESULT IN THE UNINTENDED DEPLOYMENT OF AIR
BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM
RESULTING IN DAMAGE TO THE VEHICLE AND
PERSONAL INJURY.
Observe the following cautions when handling
the batteries for the remote control unit.
Proper Use of the Batteries
Use only specified battery (CR2025).
Match the polarity of the battery with the () and ()
marks in the battery case.
Replace a dead battery as soon as possible.
Remove the battery from the remote control unit
when not using it for an extended period of time.
Insulate the battery (by placing them in a plastic bag
or covering them with vinyl tape) before disposal or
storage.
Do not disassemble, recharge, heat or short the
battery. Do not throw a battery into a fire or water.
Follow local regulations when disposing of a battery.
Improper use of a battery may cause overheating, an
explosion or ignition, resulting in injury or a fire.
Refer wiring and installation to qualified service
personnel.
Observe the following cautions of the wiring
diagram
To prevent damage to the unit, be sure to follow the
connection diagram.
Be sure to insulate any exposed wires to prevent short
circuiting with the car chassis. Bundle all cables,
and prevent cable terminals from touching any metal
parts.
Note that if your car has a driving computer or a
navigation computer, disconnecting the cable from
the battery may clear the memory.
Installation of this unit requires special skills and
experience. For maximum safety, have it installed by
your dealer. Panasonic is not liable for any problems
resulting from your own installation of the unit.
Follow the instructions to install and wire the
product.
Not following the instructions to properly install and
wire the product could cause an accident or fire.
Take care not to damage the leads.
When wiring, take care not to damage the leads.
Prevent them from getting caught in the vehicle
chassis, screws, and moving parts such as seat rails.
Do not scratch, pull, bend or twist the leads. Do not
run them near heat sources or place heavy objects on
them. If leads must be run over sharp metal edges,
protect the leads by winding them with vinyl tape or
similar protection.
Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate
tools to install the product. The use of parts other
than those supplied or designated may result in
internal damage to the unit. Faulty installation may
lead to an accident, a malfunction or fire.
Do not block the air vent or the cooling plate of the
unit.
In case of battery leakage
Thoroughly wipe the battery liquid off the battery case
and insert new battery.
If any part of your body or clothing comes into
contact with battery liquid, wash it with plenty of
water.
If battery liquid comes into contact with your eyes,
wash them with plenty of water and get immediate
medical attention.
Run the cords avoiding the spots where the
temperature can be extremely high.
Observe the following cautions of the display
Avoid physical shock on the display.
Do not place any object on the display unit, or subject
it to undue force.
Do not move the display forcibly.
The monitor movable range may be limited by a type
of car, a position where the display is mounted. etc.
Observe the following cautions of the aspect
ratio
If water drops or similar wet substances get inside
the monitor, it may cause a malfunction.
This is to remind you that compression or extension
of the screen using the aspect ratio (screen mode)
changing function of this product for commercial
purpose of profit making or viewing/listening by
the public could infringe on the rights of the author
protected by the copyright law.
Blocking these parts will cause the interior of the unit
to overhead and will result in fire or other damage.
Do not install the product where it is exposed to
strong vibrations or is unstable.
Avoid slanted or strongly curved surfaces for
installation. If the installation is not stable, the unit
may fall down while driving and this can lead to an
accident or injury.
If you expand normal picture (4 to 3) by using
“CINEMA”, “ZOOM” or “FULL” aspect to the full of the
screen, you might not see the periphery of the picture,
or you might see a distorted picture. Therefore, use
the “NORMAL” mode to see the original pictures as
the author intended it.
Installation Angle
The product should be installed in a horizontal
position with the front end up at a convenient angle,
but not more than 30.
The user should bear in mind that in some areas there
may be restrictions on how and where this unit must
be installed. Consult your dealer for further details.
CY-VM7203W
CY-VM7203W
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
(continued)
Notes on Use
Contents
English
2
Liquid Crystal Panel
Please follow the laws and regulations of your province or country for installation of the unit.
Storage temperature range: 20 °C to 80 °C
When the liquid crystal panel reaches high temperatures
or low temperatures, chemical changes occur within
the liquid crystal panel which may cause malfunctions.
Do not strongly impact the liquid crystal panel.
When the temperature is very cold or very hot, the
image may not appear clearly or may move slowly.
Also, movement of the image may seem to be out
of synchronization or the image quality is not a
malfunction or problem.
5
6
42
Connection of Side Brake Connecting Lead
This system is designated so that you
cannot see moving pictures while you are
driving.
Usage temperature range: 0 °C to 40 °C
There may be red spots, blue spots and green spots on
the panel surface. This is a characteristic of liquid crystal
panels and is not a problem. The liquid crystal panel is
built with very high precision technology and has at least
99.99 % effective image pixels. Be aware that on 0.01 %
of the panel there may be missing pixels or constantly
light pixels.
In order to protect the liquid crystal panel, keep it out
of direct sunlight while the unit is not in use.
Sudden changes in the temperature inside the car such
as those which occur immediately after the car’s air
conditioner or heater has been turned on may cause
over due to water vapor or it may cause condensation
(droplets of water) to form and, as a result, the panel
may not work properly. Do not use the unit while these
symptoms are in evidence but leave the unit standing
for about hour, and then resume or start use.
Park your car in a safe and pull the side brake (parking
brake) lever before watching the monitor.
If a rear monitor (option) is connected to this unit, you
can continually see the rear monitor image even if the
parking brake (side brake) has not been pulled on.
Warning
When you connect external devices to Video Input
Terminal (AV-IN/VIDEO 1-IN/VIDEO 2-IN), be sure to
connect the parking brake (side brake) connection
lead. (page 31)
Safety Information..................... 2
Notes On Use ........................... 7
Features................................. 8
System Connection Example......... 9
Preparation ............................ 10
Components ........................... 11
Name of Controls and Functions ... 12
General................................. 14
AV/VIDEO 1/VIDEO 2.................. 16
Car Navigation System............... 17
Aspect Ratio ........................... 17
Display Settings (SCREEN).......... 18
DIMMER, CONTRAST, BRIGHT,
COLOR, TINT........................................... 18
User Settings (USER) ................ 20
SPEAKER, NAVI INPUT,
CAMERA SETUP...................................... 20
DISPLAY UNIT ........................................ 22
ID-CODE, ACC SELECT............................ 24
Installation............................. 26
Electrical Connections ............... 32
Troubleshooting....................... 38
Maintenance........................... 40
Specifications ......................... 41
CY-VM7203W
CY-VM7203W
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Panasonic welcomes you to our constantly growing family of electronic products owners. We endeavor to give you the
advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and
assembled by people who are proud of the reputation their work has built for our company. We know this product will
bring you many hours of enjoyments, and after you discover the quality, value and reliability we have built into it, you too
will be proud to be a member of our family.
In Case You Forget the ID Code...
In case you forget the ID code, please consult your
nearest Panasonic Service Centre.
7
8
ID code memo
Copy the memo below, fill in the ID code, and keep it in a
secure location.
CY-VM7203W
In-dash 7 Widescreen Color LCD Monitor
Model No. CY-VM7203W
ID CODE
7-inch wide LCD (Liquid Crystal Display)
Delivers images of high quality and superb color
reproduction.
Built-in automatic dimmer
The brightness of the screen is automatically adjusted in
response to surrounding brightness.
Multi-standards (PAL, NTSC and SECAM)
Automatically switching to PAL, NTSC and SECAM allows
you to use a connected device without concern for its
video standard.
To enjoy the TV broadcast
Connect Panasonic TV tuner (CY-TUP133W/TUN133W,
option) and TV antenna.
3 video input terminals (2 video and 1 set
of AV), 1 set of AV output terminal and
Note:
It is not possible to check the video format just by
looking at the image on the screen.
RGB input connector
A DVD player/receiver, TV tuner or Rear View Camera
can be connected to the video input terminals, a second
monitor, can be connected to the video output terminals,
and a Panasonic Car Navigation System can be connected
to the RGB input connector.
The format cannot be checked from the OSD display
either, but that does not indicate a malfunction.
Check the disc format of the image displayed on
this monitor through menu operations on the device
connected to the monitor. For details, refer to the
instruction manual of the connected device.
System Connection Example
This unit can be combines with other components like shown below. For more details, refer to the operating instructions
for the connected devices.
ID Code
4-digit ID code for increased security.
Fully powered display positioning
Note:
mechanism
It is not possible to check the video format just by looking at the image on the screen.
The format cannot be checked from the OSD display either, but that does not indicate a malfunction.
Check the disc format of the image displayed on this monitor through menu operations on the device connected to the
monitor. For details, refer to the instruction manual of the connected device.
Market conditions regarding optional devices vary with countries and regions. Fur further information, consult your
dealer.
Fill in the ID code memo. (page 9)
Positioning of the display unit is fully power driven.
This includes extending the unit, raising it to upright
position, adjusting its vertical (tilt) angle.
CY-VM7203W
(Rear View Camera)
DVD player/receiver:
CQ-D5501W, option
TV tuner:
CY-TUP133W/CY-TUN133W, option
CY-VM7203W
CY-VM7203W
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Components
Item
Diagram
Qty
Remote Control Unit
Preparation Before Initial Use
Settings (Only by Remote
Control Unit)
1
Color LCD Monitor
9
10
Warning
Keep a battery away from children to avoid the
risk of accidents. If an infant ingests a battery,
please seek immediate medical attention.
Pull the insulation film out
from the backside of remote
control gently.
1
1
ACC selection ON/OFF
Remote Control Unit
(EUR7641050)
Execute “ACC SELECT” setting. (page 24)
ID Code
Caution
Execute “ID-CODE” setting. (page 24)
Lithium Battery for Remote
Control Unit
(Included in the remote
control)
Remove and dispose of an old battery immediately.
Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
Battery Replacement
Remove the battery holder with the remote control unit
placed on a flat surface.
Follow local regulations when disposing of a battery.
Improper use of a battery may cause overheating,
an explosion or ignition, resulting in injury or a fire.
<CR2025/1F>
1
1
1
Power Connector
(YAJ024C119CA)
Stick your thumbnail into the groove, and push
the holder in the direction of the arrow at the same
time.
Wiping Cloth
(YEFX9991793)
Tough pointed object
Pull it out in the direction
of the arrow using a
Screen
Execute “DIMMER”, “CONTRAST”, “BRIGHT”, “COLOR”
or “TINT” setting. (page 18)
Operating Instructions
(YFM284C544ZA)
tough pointed object.
Back side
Monitor
Execute “TILT” (tilt angle adjustment) setting. (page
22)
Installation Hardware (screws, cords, etc.) (page 27)
Execute “OPEN/CLOSE” (monitor setting when power
on) setting. (page 22)
Put a battery in the case with () side facing up.
Put the case back.
You may need to set the following depending on the
devices to be connected.
Note:
The number in parenthesis underneath each accessory
part name is the part number for maintenance and
service.
Accessories and their parts numbers are subject to
modification without prior notice due to improvements.
Car Navigation
Execute “NAVI INPUT” (Navigation Input Selection)
setting. (page 20)
Rear View Camera
Execute “CAMERA SETUP” (Rear View Camera Setup)
setting. (page 20)
Note:
Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
(Included in the remote control)
Battery Life: Approximately 6 months under normal use
(at room temperature)
CY-VM7203W
CY-VM7203W
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Controls and Functions
Display Unit (Display Raised)
Remote Control Unit
Aim the remote control at the remote control sensor of
the Display Unit and operate it. (previous page)
11
12
[ASP] (ASPECT)
[TILT]
Selects the aspect ratio. (page 17)
Adjusts the monitor position. (page 15)
Tilts the monitor temporarily. (page 15)
[MUTE]
Mutes the sound temporarily.
(page 14)
[OPEN] (CLOSE)
Opens/closes the monitor. (page 14)
[VOL ] [VOL ]
Adjusts the sound volume. (page 14)
[SRC/PWR] (Source/Power)
Switches on/off the power. (page 14)
Changes the source such as sound and
picture. (page 14)
[MENU]
Shows the menu screen. (page 18)
Closes the menu. (page 19)
7 inches Wide LCD
Display
[ENT] (ENTER)
Determines an operation or item.
(page 18)
[] []
Selects (vertically) or adjusts an
operation or item. (page 18)
[] []
Selects (horizontally) or adjusts an
operation or item. (page 15, 18)
Dimmer sensor
Built-in speaker
Note:
Menu-related operations (DISPLAY/USER settings) can
only be carried out from the remote control unit. They
are not possible from the buttons on the monitor. Other
operations can be performed from the unit.
[MUTE]
[NAVI] (Navigation)
Put navigation screen on the display.
(page 17)
Mutes the sound temporarily. (page 14)
[VOL ] [VOL ]
Adjusts the sound volume. (page 14)
Note:
[NAVI] button is the only for Car
Navigation System that connected to
this unit.
[SRC/PWR] (Source/Power)
Switches on/off the power. (page 14)
Changes the source such as sound and picture. (page 14)
Closes the menu. (page 19)
Display Unit (Display Closed)
Remote control sensor
CY-VM7203W
CY-VM7203W
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Display Position Adjustment
13
14
Tilt Angle Adjustment (TILT)
Adjustment is operated only be the remote control unit.
[TILT]
Press and hold [TILT] on the display unit for more
[MUTE]
[VOL ] [VOL ]
[SRC/PWR] (Source/Power)
[OPEN] (CLOSE)
than 2 seconds.
Press [] or [] to adjust.
The setup is the same as from MENU. (page 22)
Power
Warning
Do not touch the unit while the display is moving.
Inserting hands, fingers or foreign objects into the
unit can cause injuries and damage to the unit.
Keep babies and children away from the unit.
Turn your car’s ignition key to the ACC or ON position.
ON: Press [SRC/PWR] on the display unit.
Press [SRC] (PWR) on the remote control.
OFF: Press and hold [SRC/PWR] again for more than 1
seconds on the display unit.
5
1
Press and hold [SRC] (PWR) again for more than 1
seconds on the remote control.
[MUTE]
Notes:
Note:
[SRC] (PWR)
(Source/Power)
[VOL ] [VOL ]
Adjust the angle from “Display Unit Adjustment
(DISPLAY UNIT)” of “User Settings (USER)”. (page
22)
You cannot turn on the power via the remote control
when “OFF” is selected in “ACC SELECT”. (page 24)
Vertical angle (TILT) is saved in the memory, so when
the display unit is drawn out next, it is automatically set
at the angle and in the position adjusted before.
After adjusting its angle, also adjust the brightness as
well. (page 18)
Source (page 16)
Press [SRC/PWR] to change the source.
AV
The car model and installation condition may impose
some restrictions on the adjustment of the monitor’s
angle.
VIDEO 1
VIDEO 2
[]
[]
Display Open/Close
OPEN: Press [OPEN] (CLOSE).
Note:
Folding Down the Display
Temporarily
Select the same source (AV/VIDEO 1/VIDEO 2) as
the terminal that is connected to the optional external
device (AV-IN/VIDEO 1-IN/VIDEO 2-IN).
CLOSE: Press [OPEN] (CLOSE) again.
Tip the monitor forward temporarily to operate the
Note:
switches and other controls on the back of the monitor.
When the display unit is opened, “TILT” indicator lights.
If the unit stops halfway, press [OPEN] (CLOSE) again
and draw it all the way in.
Opening/closing the display can also be done when the
power is off (ACC ON).
Volume
[VOL ]: Increase
[VOL ]: Decrease
Setting Range: 0 to 30
Fold Down: Press [TILT] on the display unit.
Raise: Press [TILT] again on the display unit.
Note:
Note:
Even when the unit is power off, you can fold down the
display temporarily.
The sound level for each source is stored in memory.
The volume setting must be balanced with the
connected device. Adjust volume from the device side.
Use this unit at close to the default volume level, rather
than at maximum or minimum volume.
Caution
Avoid physical shock on the display.
Do not place any object on the display unit, or
subject it to undue force.
Do not move the display forcibly.
The monitor movable range may be limited by a type
of car, a position where the display is mounted. etc.
Mute
MUTE ON: Press [MUTE].
MUTE OFF: Press [MUTE] again.
CY-VM7203W
CY-VM7203W
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
AV/VIDEO 1/VIDEO 2
You can view the images and listen to the sounds form
the connected external devices (option) in the AV,
VIDEO 1 and VIDEO 2 source respectively.
Aspect Ratio
Default: NORMAL
Mode: 4 types
Car Navigation System
Preparation:
Warning
Specify the correct terminal that is connected to the car
navigation system in the “NAVI INPUT” operation on
the “User Settings (USER)”. (page 20)
15
16
When you connect external devices to Video Input
Terminal (AV-IN/VIDEO 1-IN/VIDEO 2-IN), be sure to
connect the side brake (parking brake) connection
lead. (page 31)
Press [ASP] (ASPECT) on the display unit to change the
aspect ratio as follows.
Preparation:
Connect an optional external device to the unit.
Press [NAVI] to change to the car navigation source.
Press [NAVI] again to cancel.
NORMAL
The conventional display image
has a 4 to 3 ratio of horizontal
to vertical.
In this case, a blank area
remains on the right and left
sides of the display.
Note:
AV/VIDEO 1/VIDEO 2
Press [SRC/PWR] to change the source.
Recommended example:
If the navigation source is ON, only the audio signal is
switched while the video signal remains as it is and the
image is shown on the “FULL” screen only.
The source can be changed even when the display unit
is in the retracted position.
AV-IN:
TV tuner
(CY-TUP133W/TUN133W,
option)
VIDEO 1-IN:
DVD player/receiver
(CQ-D5501W, option)
AV
VIDEO 1
FULL
The screen is extended
horizontally as a whole to the
aspect ratio of 16 to 9.
The extension ratio is the same
at any point of the screen.
VIDEO 2
Source display
RGB:
VIDEO 2-IN:
Rear View Camera
ZOOM
Car Navigation System
The screen is fully extended at
the normal aspect ratio of 4 to
3.
The top and bottom of the
screen are slightly cut.
[ASP] (ASPECT)
CINEMA
The display is only zoomed
vertically.
The top of the screen will be
cut off, but the bottom will not
be.
Panasonic TV Tuner (CY-TUP133W/
TUN133W, option)
Select AV source.
Connect a Panasonic TV tuner to AV-IN connectors.
(page 35)
Note:
DVD Player/Camcorder
When the Rear View Camera is in operation with the
transmission gear shift in the reverse position, the
image is shown on the “FULL” screen only.
In some cases, the picture looks different from the
original one due to your selection of aspect.
Recommended source: VIDEO 1
Select the same source (VIDEO 1 or VIDEO 2) as the
terminal that is connected to a DVD player or camcorder
(VIDEO 1-IN or VIDEO 2-IN).
[SRC/PWR] (Source)
[NAVI] (Navigation)
Rear View Camera
Caution
Recommended source: VIDEO 2
This is to remind you that compression or extension
of the screen using the aspect ratio (screen mode)
changing function of this product for commercial
purpose of profit making or viewing/listening by
the public could infringe on the rights of the author
protected by the copyright law.
Select the same source (VIDEO 1 or VIDEO 2) as the
terminal that is connected to a Rear View Camera
(VIDEO 1-IN or VIDEO 2-IN).
Execute “CAMERA SETUP” (Rear View Camera Setup)
setting. (page 20)
[SRC] (PWR)
(Source)
If you expand normal picture (4 to 3) by using
“CINEMA”, “ZOOM” or “FULL” aspect to the full
of the screen, you might not see the periphery of
the picture, or you might see a distorted picture.
Therefore, use the “NORMAL” mode to see the
original pictures as the author intended it.
Car Navigation System
Select the same source (VIDEO 1 or VIDEO 2) as the
terminal that is connected to a Car Navigation System
(VIDEO 1-IN or VIDEO 2-IN).
Execute “NAVI INPUT” (Navigation Input Selection)
setting. (page 20)
CY-VM7203W
CY-VM7203W
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Settings (SCREEN)
[SRC] (PWR)
(Source)
17
18
[MENU]
[ENT] (ENTER)
[] []
[] []
Menu display (SCREEN)
[SRC/PWR] (Source)
Note:
Menu
Submenu
Setting
Only English is displayed on SCREEN/USER
settings.
Menu-related operations (DISPLAY/USER
settings) can only be carried out from the remote
control unit. They are not possible from the
buttons on the monitor.
Press [MENU] to display
Press [] or [] to select the
Press [] or [] to adjust.
Note:
the menu.
item.
Press [ENT] (ENTER) to set (Dimmer setting only).
Press [SRC/PWR] to exit the menu.
Press [MENU] in the setting display to return to the
menu display (SCREEN).
Press [] or [] to select Press [ENT] (ENTER).
“SCREEN”.
: automatically adjusted according to
ambient light intensity.
AUTO
Dimmer (Adjust the
Brightness)
Select
1
2
3
4
DIMMER
Default: AUTO
Darker
Brighter
Setting range: AUTO, 1 to 4
[]: Increases the contrast between black and white.
Adjust the Image Contrast
Select
[]: Decreases the contrast between black and white.
Default: 0
CONTRAST
Setting range: 15 to 15
Select
[]: Lightens.
Adjust the Image
Brightness
Select
SCREEN
[]: Darkens.
BRIGHT
Default: 0
Setting range: 15 to 15
[]: Deepens the depth of color on the display.
Adjust the Image Color
Depth
Select
[]: Lightens the depth of color on the display.
COLOR
Default: 0
Setting range: 15 to 15
[]: Emphasizes green in the color image.
Note:
Adjust the Image Tone or
Tint
“TINT” is adjustable only when NTSC signal is shown
on the display.
Select
[]: Emphasizes red in the color image.
TINT
Default: 0
Setting range: 15 to 15
CY-VM7203W
CY-VM7203W
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
User Settings (USER)
[SRC] (PWR)
(Source)
19
20
[MENU]
[ENT] (ENTER)
[] []
[] []
Menu display (USER)
Menu
Submenu
Setting
[SRC/PWR] (Source)
Note:
Press [MENU] to display
Press [] or [] to select the
Press [] or [] to adjust.
Note:
Only English is displayed on SCREEN/USER
settings.
Menu-related operations (DISPLAY/USER
settings) can only be carried out from the remote
control unit. They are not possible from the
buttons on the monitor.
the menu.
item.
Press [ENT] (ENTER) to set.
Press [SRC/PWR] to exit the menu.
Press [MENU] in the setting display to return to the
menu display (USER).
Press [] or [] to select Press [ENT] (ENTER).
“USER”.
OFF: No sound of built-in speaker is output.
AUTO: Sound of the external device shown on the
display is output.
Built-in Speaker Output
Selection
Select
SPEAKER
NAVI: Sound of the car navigation system is output.
Default: AUTO
Setting range: OFF, AUTO, NAVI
RGB: Connected to the RGB input cord or a Car
Navigation System not connected.
AV: Connected to the AV-IN.
VIDEO 1: Connected to the VIDEO 1-IN.
VIDEO 2: Connected to the VIDEO 2-IN.
NAVI INPUT:
NAVI INPUT (Navigation
Input Selection)
sets the terminal to which a Car Navigation System is
connected.
Select
Default: RGB
Note:
Setting range: RGB, AV, VIDEO 1, VIDEO 2
NAVI INPUT
Set to “AV” when connecting to a non-Panasonic Car
Navigation System. (page 34)
Select
USER
Press [] or [] to select the item.
SCALE:
CAMERA SETUP (Rear
View Camera Setup)
Images through the Rear View Camera can be shown in
scale display mode.
CAMERA INPUT:
sets the terminal to which a Rear View Camera is
connected.
CAMERA INPUT (Rear View Camera input
selection):
OFF: scale display off.
ON: scale display on.
Select
Default: OFF
Setting range: OFF, AV, VIDEO 1, VIDEO 2
CAMERA SETUP
OFF: Unconnected.
AV: Connected to the AV-IN.
VIDEO 1: Connected to the VIDEO 1-IN.
VIDEO 2: Connected to the VIDEO 2-IN.
SCALE ADJUSTMENT:
SCALE (Rear View Camera scale):
Default: OFF
[] or []: adjust.
Setting range: OFF, ON
SCALE ADJUST (Scale adjustment):
(Page 22, 24)
CY-VM7203W
CY-VM7203W
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
User Settings (USER)
(continued)
[TILT]
[SRC] (PWR)
(Source)
21
22
[MENU]
[ENT] (ENTER)
[] []
[] []
Menu display (USER)
Menu
Submenu
Setting
[SRC/PWR] (Source)
Note:
Press [MENU] to display
Press [] or [] to select the
Press [] or [] to adjust.
Note:
Only English is displayed on SCREEN/USER
settings.
Menu-related operations (DISPLAY/USER
settings) can only be carried out from the remote
control unit. They are not possible from the
buttons on the monitor.
the menu.
item.
Press [ENT] (ENTER) to set.
Press [SRC/PWR] to exit the menu.
Press [MENU] in the setting display to return to the
menu display (USER).
Press [] or [] to select Press [ENT] (ENTER).
“USER”.
(Page 20)
TILT:
OPEN/CLOSE:
Display Unit Adjustment
5
1
1
2
3
4
5
TILT (Tilt angle adjustment):
Default: 5
AUTO: The monitor is opened automatically when
turning ON ACC.
MANUAL: The monitor is not opened automatically.
Setting range: 1 to 5
OPEN/CLOSE (Monitor setting when power
on):
Default: MANUAL
Select
Select
Note:
The monitor position setting menu can also be
displayed be pressing [TILT] on the display unit for
more than 2 seconds. (page 15)
DISPLAY UNIT
USER
Setting range: MANUAL, AUTO
The car model and installation condition may impose
some restrictions on the adjustment of the monitor’s
angle.
(Page 24)
CY-VM7203W
CY-VM7203W
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
User Settings (USER)
(continued)
[SRC] (PWR)
(Source)
23
24
[MENU]
[ENT] (ENTER)
[] []
[] []
Menu display (USER)
[SRC/PWR] (Source)
Note:
Menu
Submenu
Setting
Press [] or [] to adjust.
Press [ENT] (ENTER) to set.
See below to set the ID code.
Only English is displayed on SCREEN/USER
settings.
Menu-related operations (DISPLAY/USER
settings) can only be carried out from the remote
control unit. They are not possible from the
buttons on the monitor.
Press [MENU] to display
Press [] or [] to select the
Note:
the menu.
item.
Press [MENU] in the setting display to return to the
menu display (USER).
Press [] or [] to select Press [ENT] (ENTER).
“USER”.
Press [SRC/PWR] to exit the menu.
(Page 20, 22)
How to set your ID code (for the first time)
Press [], [], [] or [] to enter an 4 digit
code.
Press [ENT] (ENTER) to set.
Press [], [], [] or [] to enter an 4 digit code
again.
How to cancel the known ID code
ID Code Setting
Press [], [], [] or [] to enter the preset (old)
4 digit code. If the wrong ID code is entered, it is not
possible to cancel the ID code setting display.
Press and hold [ENT] (ENTER) to cancel the known
ID code.
Prior to operating this unit, it is advisable
to assign a 4-digit ID code for security.
Once the ID code has been set, the unit
cannot be operated if the main power supply
is disconnected then re-connected. It is
electrically locked so that a thief cannot use
the stolen unit unless that person knows the
code you have set.
“Complete!” is displayed. The ID code setting is
completed.
Note:
Should your unit ever require service, cancel your ID
code before sending for repair.
The inputted code is not displayed for your security.
How to change your ID code
Press [], [], [] or [] to enter the preset (old)
Select
The ID code operation must be performed only
by the person to whom the unit begins.
ID-CODE
4 digit code.
Press [], [], [] or [] to enter an new 4 digit
code.
Caution
Generally, it is not necessary to enter the ID
code each time when using the unit if it has
not been disconnected from the main power
supply (car battery).
Select
Press [ENT] (ENTER) to set.
Press [], [], [] or [] to enter an 4 digit code
Record your registered ID code and keep it in a
secure location. (Fill in the ID code memo. (page
9))
USER
again.
If you forget it, you will be unable to use the unit.
In case you forget the ID code, please consult your
nearest Panasonic Service Center.
Default: none
OFF: set to OFF if your car has no ACC position.
ON: set to ON if your car has ACC position.
ACC Selection ON/OFF
Default: ON
Caution
Be sure to select OFF when your car has no ACC
position in the ignition switch. Failure to do this
could cause the battery to go dead.
Note:
Select
You cannot turn on the power via the remote control
when “OFF” is selected in “ACC SELECT”.
ACC SELECT
CY-VM7203W
CY-VM7203W
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
No.
Item
Diagram Qty.
Installation Hardware
(For Installation)
Preparation
Dashboard Installation
Spacer
2
25
26
Installation Opening
Caution
No.
Item
Diagram Qty.
Double-Faced Adhesive Tape
1 set
This unit can be installed in any dashboard having an
opening as shown below. The dashboard should be 4.5
mm–6 mm thick in order to be able to support the unit.
Please follow the laws and regulations of your
province or country for installation of the unit.
When bending the mounting tab of the mounting
collar with a screwdriver, be careful not to injure
your hands and fingers.
Trim Plate
1
(ZZBISVD7001E)
(YFC054C087CA)
1
Mounting Collar
53 mm
Installation Hardware
(For Wiring)
We strongly recommended you to wear gloves for
installation work to protect yourself from injuries.
(YFX214C433CA)
2
182 mm
No.
Item
Diagram
Qty.
Mounting Spring
Disconnect the cable from the negative () battery
terminal (see caution below).
The unit should be installed in a horizontal position with
the front end up at a convenient angle, but not more
than 30.
Power Connector
1
(YFX054C077CA)
1
Installation Precautions
This unit should be installed by a professional installer.
In case of difficulty, please consult your nearest
authorized Panasonic Service Center.
Mounting Bolt (5 mm)
(YAJ024C119CA)
1
Tapping Screw
(5 mm16 mm)
1
1
Reverse Extension Cord
Clip Connector
This system is to be used only in a 12 V DC battery
system (car) with negative ground.
Follow the electrical connections carefully (page 32).
Failure to do so may result in damage to the unit.
Connect the power lead after all other connections are
made.
Be sure to connect the battery lead (yellow) to the
positive terminal () of the battery or fuse block (BAT)
terminal.
Insulate all exposed wires to prevent short circuiting.
Secure all loose wires after installing the unit.
Please carefully read the operating instructions of the
respective equipment before connecting it to this unit.
Hex. Nut (5 mm)
(WAVS05M6000T)
1
030
(ZZBISVD7001A)
1
Rear Support Strap
Caution
(YEAT034C012)
If your car is equipped with air bag and/or anti-
theft systems specific procedures may be required
for connection and disconnection of the battery to
install this product.
(YFG044C002ZA)
2
Note:
Round Head Screw
(5 mm6 mm)
The number in parenthesis underneath each accessory
part name is the part number for maintenance and
service.
Accessories and their parts numbers are subject to
modification without prior notice due to improvements.
Use the supplied screws for installation exclusively. In
case of losing any of them, please order the specific
screw.
Before attempting installation of this electronic
component contact your car dealer or
manufacturer to determine the required procedure
and strictly follow their instructions.
FAILURE TO FOLLOW THE PROCEDURE MAY
RESULT IN THE UNINTENDED DEPLOYMENT OF
AIR BAGS OR ACTIVATION OF THE ANTI-THEFT
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE
AND PERSONAL INJURY.
Flat-Head Screw
(5 mm6 mm)
4
4
Round Head Screw
(4 mm3 mm)
(ZZBISVD7001B)
Transportation Bracket Removal
Be sure to remove the transportation brackets before use
(installation). Use screws (5 mm6 mm) with washers for
installation.
Round Head Screw
(5 mm6 mm)
Be careful not to lose these screws.
Round Head Screw
(5 mm6 mm)
Transportation Bracket
Transportation Bracket
CY-VM7203W
CY-VM7203W
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
(continued)
Mounting the Unit
Method for Fixing the Mounting Spring
27
28
Two holes of the mounting spring allow you to select between two mounting types as shown below.
Installation Procedures (When Using Mounting Collar )
(A) Regular Installation Method
(B) Deeper Installation Method
Note:
Insert the Mounting Collar into the dashboard,
and bend the mounting tabs out with a
screwdriver.
The car model, installation conditions and combination
of the units used may impose some restrictions on
opening and closing the monitor as well as on the angle
and position to which the monitor can be adjusted.
IMPORTANT
Fastening the Mounting Collar
How much to bend the tabs will vary depending
on the car. Bend them with a screwdriver to
fasten the Mounting Collar securely in the
dashboard.
When this unit is installed in dashboard, ensure that there
is sufficient air flow around the unit to prevent damage
from overheating, do not block any ventilation holes on
the unit.
Less projecting
Flat-Head Screw
A few millimeters of console projecting
Dashboard
Flat-Head Screw
Mounting Collar
Tab
Flat-Head Screw
(5 mm6 mm)
Flat-Head Screw
Flat-Head Screw
Mounting Spring
Caution
Method (B) is not available in some types of cars.
Mounting Bolt
(5 mm)
Method for Fixing the Rear of the Unit
(a) Using the Rear Support Strap
(b) Using the Rubber Cushion
(Option)
Power Connector
Fire wall of car
Rear Support Bracket
(Provided on the Car)
Attach the Mounting Springs to the unit.
3 mm
Tapping screw
Establish the rear connection of the unit.
Mounting Bolt (5 mm)
After fixing Power Connector , fix the rear of the unit to
the car body by either method (a) or (b) shown at right.
Mounting Bolt (5 mm)
Insert the unit into Mounting Collar .
Secure the clamp plate of Mounting Collar to the hook
of Mounting Spring .
Hex. Nut
Insert Trim Plate .
Clamp plate
Rubber Cushion (option)
After installation, reconnect
Rear Support Strap
the negative () battery
terminal.
CY-VM7203W
CY-VM7203W
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
(continued)
Installation Procedures (When Using Mounting Collar )
Connecting the Parking Brake (Side Brake) Connection Lead
29
30
Use the brackets supplied with your car when mounting this unit. The bracket shape and mounting method vary with car
manufacturers, car types and manufacturing year. Please consult your nearest dealer or installer.
Caution
For safety, be sure to ask your nearest professional
Select mounting screws according to the hole positions and hole shape of the bracket.
installer to do this connection.
Round Head Screw (5 mm6 mm)
2 pieces
Recycle the Round Head Screws that fixed the transportation brackets for
two more positions.
Parking brake (side brake)
switch
Hand brake
Foot brake
Round Head Screw (4 mm3 mm)
When using these
mounting holes
4 pieces
Flat-Head Screw (5 mm6 mm)
4 pieces
The parking brake (side brake) switch position varies with the car
model. For details on the exact location of the parking brake (side brake)
switch in your car, contact your dealer.
Use the supplied Spacer if mounting hole of your car is shaped like below.
Round Head Screw (5 mm6 mm)
Spacer
Clip Connector
Mounting Hole
of a Bracket (in
section)
Battery
Car chassis
Parking Brake (Side Brake) Connection
Lead
(Bright green)
When the parking brake (side brake) lever
is engaged, the unit is grounded by the
chassis.
Bracket
Existing Bracket (R)
Brake light
Double-Faced
Adhesive Tape
Round Head Screw
Spacer
(5 mm6 mm)
Double-Faced Adhesive Tape
Existing Bracket (L) (Bracket originally attached to the car)
Attach a Clip Connector to the end of the parking
The Clip Connector is connected to the power
source side lead of the parking brake (side brake)
lever.
brake (side brake) connection lead.
To Remove the Unit
After removing the right and left clamp plates, pull
Push the right and left clamp plates outward, one at
Come up to this point.
the unit with both hands till it comes out.
a time, and pull the unit toward yourself.
Push here to
remove the
clamp plates.
Parking Brake (Side Brake)
Connection Lead
(Bright green)
Power source side lead
To remove Trim Plate , pull it from right side to left side.
CY-VM7203W
CY-VM7203W
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
Wiring Diagram
31
32
CY-VM7203W (Rear)
Caution
AV-IN
This unit is designed for use in a car having a 12 V
negative ground battery system.
To prevent damage to the unit, be sure to follow the
connection diagram.
Do not insert the power connector into the unit until
the wiring is completed.
Be sure to insulate any exposed wires to prevent
short circuiting with the car chassis. Bundle all
cables, and prevent cable terminals from touching
any metal parts.
R (Red)
Video
(Yellow)
VIDEO 1-IN
(Yellow)
L (White)
Note that if your car has a driving computer or a
navigation computer, disconnecting the cable from
the battery may clear the memory.
Run the cords avoiding the spots where the
temperature can be extremely high.
ACC Power Lead
(Red)
To ACC power, 12 V DC.
Power Connector
Battery Lead
(Yellow)
Note:
To the car battery, continuous 12 V DC.
Strip about 5 mm of the lead ends for connection.
Be sure to fully plug in the connectors. Secure them
with clamps and tapes.
All other installation methods require the use of
dedicated metal fittings. Consult with a qualified
servicing engineer or your dealer if other methods are
required.
Ground Lead
(Black)
To a clean, bare metallic part of the car chassis.
Remote-out Cord
(Black)
To the remote input terminal of the devices.
Parking Brake (Side Brake) Connection Lead
(Bright green)
Be sure to wire the parking brake (side brake) for safety and
preventing accidents.
L (White)
Preout Cord
To the audio input connector of the car audio
player/receiver (option)
R (Red)
Video output Cord
Video (Yellow)
To the video input connector of the Rear Monitor (option).
Video input 2 (VIDEO 2-IN) cord
(Yellow)
Reverse Lead
(Violet/white stripe)
When connecting the Rear View Camera, use the reverse
lead.
CY-VM7203W
CY-VM7203W
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
(continued)
Connecting with DVD Player/Receiver (CQ-D5501W)
Note:
Connecting with TV Tuner (CY-TUP133W/TUN133W)
Note:
33
34
Refer to the operating instructions for the connected
devices, in addition.
Refer to the operating instructions for the connected
devices, in addition.
Connect this unit to the TV tuner (CY-TUP133W/
TUN133W) with RCA cord (video, audio, remote).
Before turning off the car engine, first use the remote
control to turn off the power for the TV tuner (CY-
TUP133W/TUN133W) before turning off the power for
this monitor.
RCA Cord (option)
Video (Yellow)
VIDEO-OUT
AV-IN
TV OUT
REMOTE IN
CY-VM7203W
(Rear)
TV Tuner
CY-TUP133W/TUN133W
VIDEO 1-IN
(Yellow)
DVD player/receiver (CQ-D5501W,
option)
(option)
CY-VM7203W (Rear)
Video (Yellow)
RCA Cord (option)
Video (Yellow)
(Black)
R (Red)
L (White)
R (Red)
L (White)
RCA Cord (option)
Connecting with Car Navigation System
Note:
Refer to the operating instructions for the connected
devices, in addition.
Connecting with Rear Monitor
Set to “AV” when connecting to a non-Panasonic Car
Navigation System. (page 21)
Note:
Refer to the operating instructions for the connected
devices, in addition.
AV-IN
AV-IN
Video (Yellow)
CY-VM7203W
(Rear)
RCA Cord (option)
Video (Yellow)
RCA Cord (option)
CY-VM7203W (Rear)
R (Red)
L (White)
L (White)
R (Red)
Video (Yellow)
R (Red)
Video (Yellow)
R (Red)
Example:
Example:
Car Navigation System
Rear Monitor
Video (Yellow)
R (Red)
L (White)
Video (Yellow)
R (Red)
CY-VM7203W
CY-VM7203W
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
(continued)
Connecting with VCR or Camcorder
Note:
Connecting with Rear View Camera
Note:
35
36
Refer to the operating instructions for the connected
devices, in addition.
Refer to the operating instructions for the connected
devices, in addition.
Please observe what shapes the connectors of the
connecting devices are and where each of them is
connected to in order to establish a proper connection.
Rear View Camera
Control Unit
AV-IN
CY-VM7203W
(Rear)
Rear View Camera
Video (Yellow)
RCA Cord (option)
CY-VM7203W (Rear)
L (White)
L (White)
R (Red)
RCA Cord
(option)
Reverse Lead
(Violet/white stripe)
Video input 2 (VIDEO 2-IN) cord
Video (Yellow)
R (Red)
Connecting the Reverse Lead
If using an optional Rear View Camera, the reverse lead
must be connected.
Check the reverse lamp.
Example:
Connect the reverse lead (violet/white stripe) to the positive
() lead of the reverse lamp (the lamp with a clear lens that
lights when the transmission gear is shifted into the reverse
position).
VCR (option)
Camcorder (option)
Video (Yellow)
R (Red)
L (White)
Note:
Connect the reverse lead after cutting the terminal at the
end.
Use a Reverse Extension Cord if needed.
Take it out of the back of
the tail lamp mount.
Reverse lamp
Car chassis
Battery
Clip connector
Reverse Extension Cord
Transmission gear
(Violet/white stripe)
CY-VM7203W
CY-VM7203W
36
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Car Navigation, VCR, Camcorder, Rear View Camera, Rear Monitor
If You Suspect Something Wrong
Warning
37
38
Check and take steps as described below.
Do not use the unit in abnormal condition, for
example, without sound, or with smoke or foul
smell, which can cause ignition or electric shock.
Immediately stop using the unit and consult your
dealer.
The picture from a Car
Navigation System is not
displayed.
The connection of a Car Navigation System is not correct.
Connect it correctly.
If the described suggestions do not solve the problem, it is
recommended to take the unit to your nearest authorized
Panasonic Service Center. The product should be serviced
only by qualified personnel. Please refer checking and repair to
professionals.
Panasonic shall not be liable for any accidents arising out
of neglect of checking the unit or your own repair after your
checking.
Input setting of a Car Navigation System is not correct.
Correct the input setting.
Never try to repair the unit by yourself because it
is dangerous to do so.
The picture from a VCR
or Camcorder is not
displayed.
A VCR or a Camcorder is not connected correctly.
Connect a VCR or Camcorder correctly.
Never take measures especially those other than indicated by
italic letters in “Possible solution” described below because
those are too dangerous for users to handle themselves.
The picture from a Rear
View Camera is not
displayed.
Rear View Camera is not connected correctly.
Connect a Rear View Camera correctly.
Common
Input setting of a Rear View Camera is not correct.
Correct the input setting.
Problem
Possible cause Possible solution
No power to the unit.
The power cord (battery, power and ground) is connected in the wrong way.
Check the wiring.
Display Settings
The brightness of the
screen is not stable.
“AUTO” dimmer is selected.
Select one of the dimmer levels from among 1 to 4 to make the dimmer
adjustment become free from light intensity.
Fuse blows out.
Eliminate the cause of fuse blowout and replace the fuse with new one. Consult
your dealer.
The picture is dark.
The picture is whitish.
Something is wrong with
the picture. The picture
is light in color.
The screen is not adjusted properly.
Make every adjustment of the screen.
Sound is not generated.
MUTE is set to ON.
Set MUTE to OFF.
The speaker setting is set to “OFF”.
Set the speaker setting to “AUTO” or “NAVI”.
The display does not go
back into the unit.
The monitor stops on the way to the home position.
Press [OPEN] (CLOSE).
Noise.
There is an electromagnetic-wave generator such as a cellular phone near the unit or
its electrical lines.
Keep the electromagnetic-wave generator such as a cellular phone away from
the unit and the wiring of the unit. If noise cannot be eliminated due to the wiring
harness of the car, consult your dealer.
Red, blue, or green
spots appears.
This is a characteristic of liquid crystal panels and is not a problem.
The contact of the ground lead is poor.
Make sure that the ground lead is connected to an unpainted part of the chassis
securely.
Remote Control Unit
No response to pressing
buttons.
The battery is inserted in the wrong direction. A wrong battery is inserted.
Insert a correct battery in the correct direction.
Noise is made in step
Alternator noise comes from the car.
with engine revolutions.
Change the wiring position of the ground lead.
Mount a noise filter on the power supply.
The battery is weak.
Replace the battery with new one.
Some operations are not
executable.
Some operations are not executable in particular modes such as menu mode.
Read the operating instructions carefully and cancel the mode. If the unit is still
out of order, consult your dealer.
The aimimg direction of the remote control unit is wrong.
Aim the remote control unit at the sensor of the unit and press buttons.
The sensor is exposed to direct sunlight. (The remote control unit may not be operable
when the sensor is exposed to direct sunlight, In such a case, the system is not
faulty.)
The power of the unit
fails unintentionally.
The safety device works.
Consult your dealer, or your nearest Panasonic Service Center.
Block off sunlight to the sensor.
CY-VM7203W
CY-VM7203W
38
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
(Continued)
Specifications
Product Servicing
If the Unit Fails to Operate
General
Monitor
39
40
If the suggestions in the charts do not solve the problem,
we recommend that you take it to your nearest authorized
Panasonic Service Center. The product should be serviced
only by a qualified technician.
Reset switch
Power supply:
DC 12 V (11 V–16 V), test
Liquid crystal panel:
7 inches wide
Insert a hard, slender stick into the hole and push the
switch.
voltage 14.4 V,
negative ground
Less than 1.0 A
Screen dimensions (WHD):
14379163 mm
Number of pixels:
Current consumption:
Maximum power output
(For built-in speaker):
Video input signal:
336 960 pixels
(234 vertical
480 horizontal3)
Over 99.99 %
Transparent color filter
format
TFT (Thin Film Transistor)
active matrix format
Internal light (Built-in small
fluorescent lamp)
0.7 W
Replacing the Fuse
Composite video signal, 1.0
Vp-p (75 )
2 Vrms
Composite video signal, 1.0
Vp-p (75 )
17850165 mm
1.6 k
Valid pixel ratio:
Display method:
Use fuses of the same specified rating (3 A). Using
different substitutes or fuses with higher ratings, or
connecting the unit directly without a fuse, could cause
fire or damage to the unit.
Audio input sensitivity:
Video output signal:
Drive method:
Light source:
If the replacement fuse fails, contact your nearest
Panasonic Service Center for service.
Dimensions (WHD):
Weight:
IMPORTANT
Press the switch only when the unit fails to operate with
any buttons. (Stored settings and adjustments are not
cleared.) If the unit fails to return to normal condition, call
the nearest Panasonic Service Center and ask for repairs.
Note:
If the ID-CODE has been already set, you will be asked
to enter the ID-CODE right after the unit is restarted.
Note:
Specifications and design are subject to modification
without notice due to improvements.
Some figures and illustrations on this manual may be
different from your product.
Maintenance
Caution on Cleaning
Cleaning this Unit
When the unit is dirty, wipe the surface of the display
using the Wiping Cloth (supplied).
Cleaning without the supplied cloth
Moisten the soft cloth in dishwashing soap diluted
with water and wring well.
Alcohol
Pesticide
Wipe lightly. Go over the same surface with a dry
cloth.
Thinner
Wax
Benzine
Your product is designed and manufactured to ensure a
minimum of maintenance. Use a dry soft cloth for routine
exterior cleaning. Never use benzine, thinner or other
solvents.
Note:
Since there is the possibility of water drops getting
inside of the unit, do not directly apply cleanser to the
surface.
Do not scratch the screen with your nails or other hard
objects. The resulting scratches or marks will obscure
the images.
Caution
If water drops or similar wet substances get inside
the monitor, it may cause a malfunction.
CY-VM7203W
CY-VM7203W
40
41
Download from Www.Somanuals.com. All Manuals Search And Download.
|