Operating Instructions
<Operations and Settings>
Remote Operation Panel
Model No.ꢀ AK-HRP200G
z How the operating instructions are organized
• Basics:
This manual describes how to connect the unit to the required equipment and set it up.
Before installing the unit, be sure to read the <Basics> manual to ensure that you know how to install
it correctly.
• Operations and Settings (this manual)
Operations and Settings describe how to operate and set up the unit.
Before operating this product, please read the instructions carefully and save this manual for future use.
ENGLISH
VQT4S52A (E)
M1012KT0 -PS
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
„„Overview
„„File.types.handled.by.the.unit
This unit is a remote operation panel for controlling a studio
handy camera (AK-HC3800) and a camera controller unit like the
AK-HCU200.
Scene file
Scene files are mainly used by video
engineers (VE) to create the required image
characteristics.
Use a dedicated optical fiber cable to connect a studio handy camera
to a camera controller unit and use a dedicated ROP cable (optional
accessory) to connect this unit to the camera controller unit.
Reference file
User file
The term reference file is a generic term for
user files and factory files.
A user file is system setting data (reference
file) composed of scene files and operation
data. The user can record user files.
„„Memory.Cards
Memory cards used with the unit should conform to SD or SDHC
standards.
Be sure to use the unit to format memory cards.
Memory cards with the following capacity can be used with the unit.
SDXC memory cards are not supported.
Factory file
Lens file
A file that contains camera settings that were
stored at the factory.
Data for correcting specific lens
characteristics that are used by video
engineers (VE).
ROP configuration file
ROP specific setting data.
SD memory cards: 8 MB to 2 GB
SDHC memory cards: 4 GB to 32 GB
For the latest information not described in the Operating Instructions,
refer to the following website.
Observe the following points when using and storing this unit.
• Avoid high temperature and humidity.
• Avoid water droplets.
• Avoid static electricity.
„„Upgrade.software
You can obtain upgrade software from Service and Support on the
following website.
For the upgrade procedure, refer to the instructions included with the
download file.
„„Software.for.peripheral.equipment
Software upgrades will also become necessary for the peripheral
equipment that is connected to this unit (cameras or CCUs).
For details, consult your supplier.
„„Disclaimer.of.warranty
IN NO EVENT SHALL Panasonic Corporation BE LIABLE TO ANY
PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR
REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE
CASES, INCLUDING BUT NOT LIMITED TO BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION,
DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR
EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY
INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE
USER;
(3) UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION
OF THE PRODUCT BY THE USER;
(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES
ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE
INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE,
OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM
COMBINED BY THE DEVICES OF THIRD PARTY;
(6) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE;
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup.mode
Setup.mode
Setup mode allows the user to make a variety of unit settings, and save and load scene files and user files.
Normal operation is unavailable during setup mode operation. ROP menu (REMOTE OPERATION MENU) operation is not available either.
„„Setup.mode.functions
Setup mode allows you to do any of the following.
Item
Adjustable.range
Set camera number
Display
1
2
Sets a camera number.
Save scene file to/load scene file from memory card
Save user file to/load user file from memory card
Save lens file to/load lens file from memory card
Saves the currently used scene file to a memory card. It also allows you to load a
scene file stored on a memory card.
3
4
5
Saves the currently used user file to a memory card. It also allows you to load a
user file stored on a memory card.
Saves the currently used lens file to a memory card. It also allows you to load a
lens file stored on a memory card.
Save ROP configuration file to/load ROP configuration
file from memory card
Save a configuration file for the unit to a memory card. It also allows you to load a
configuration file for the unit stored on a memory card.
6
Format memory card
Formats a memory card
7
Select/set flare and pedestal
Set buzzer (beep/call tone)
Selects the flare and pedestal control function
Enables or disables the buzzer or call tone.
Sets the brightness of the panel LED and 7-segment display.
8
9
Set display brightness (LED/7-segment display)
10
11
12
13
14
15
16
17
18
19
For future use.
Initialize settings
Initializes unit settings.
Confirm version
Displays the version of the software used by the unit.
Saves unit data to a memory card.
Upgrades the software used by the unit.
Save unit data to memory card
Upgrade software
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup.mode. (continued)
„„Opening.setup.mode
„„Exiting.setup.mode
Setup mode differs from normal operating modes. Use the steps below
To exit setup mode, hold down <EXIT> for two seconds. The unit returns
to open setup mode.
to normal operating mode.
UP
ND
CC
SHT
SYNC
CAMERA
10-19
1..When.a.camera.and.CCU.are.connected,.select.IRIS.(to.
M.GAIN
M.PED
light.the.<IRIS>.display.on.the.panel).
If the IRIS display is not lit, press the selected <DISPLAY SELECT>
button to select IRIS.
DATA
SET
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
UP
ND
CC
SHT
SYNC
CAMERA
10-19
DOWN
SET UP
M.GAIN
M.PED
SELECT
SHIFT
+
UP+DOWN
DATA
SET
SAVE/LOAD
EXIT
EXECUTE
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
DOWN
SET UP
„„Basic.operations
SELECT
The buttons indicated in the figure below are available in setup mode.
No other buttons are available. All other LEDs stay off. (Except the
alarm display)
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
EXECUTE
1
2
3
4
IRIS display
Use the steps below to open setup mode when the power is on, but a
camera or CCU is not connected.
UP
ND
CC
SHT
SYNC
CAMERA
10-19
M.GAIN
M.PED
2..Simultaneously.hold.down.DATA.SET.<DATA.SET>.
<UP>,.<DOWN>.and.<SHIFT>.for.approximately.two.
DATA
SET
seconds.
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
This opens setup mode and Menu No. 1 (camera number setting) is
displayed.
DOWN
SET UP
SELECT
SCENE/USER FILE
SHIFT
+
UP+DOWN
SHIFT
SCENE 1
USER 1
SCENE 2
SCENE 3
SCENE 4
STORE
SAVE/LOAD
EXIT
EXECUTE
USER 2
USER 3
7
8
6
5
UP
ND
CC
SHT
SYNC
CAMERA
1..Selects.set.values
2..Indicates.selected.submenu
M.GAIN
M.PED
10-19
DATA
SET
3..Indicates.set.values.and.selected.values
4..Indicates.menu.numbers
No.
IRIS
DOWN
SET UP
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
SELECT
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
EXECUTE
5..Selects.a.menu.number..Each.press.of.the.button.
increments.menu.numbers.
1→2→3→...→19→1→2→...
6..Confirms.a.setting
7..Selects.a.submenu..Each.press.of.the.button.opens.a.
different.submenu.
8..To.exit.setup.mode,.hold.down.<EXIT>.for.two.seconds..
The.unit.returns.to.normal.operating.mode.
UP
ND
CC
SHT
SYNC
CAMERA
10-19
M.GAIN
M.PED
DATA
SET
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
DOWN
SET UP
SELECT
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
EXECUTE
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup.mode. (continued)
„„Setup.mode.menu.configuration
Setup mode is comprised of the menus and submenus listed in the table below.
Default.
value
Menu
Submenu
Set.value/Selected.operation
UP
ND
CC
SHT
SYNC
CAMERA
10-19
UP
UP
ND
CC
SHT
SYNC
CAMERA
10-19
ND
CC
SHT
SYNC
CAMERA
10-19
M.GAIN
M.PED
M.GAIN
M.PED
M.GAIN
M.PED
DATA
SET
DATA
SET
DATA
SET
No.
No.
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
DOWN
SET UP
DOWN
SET UP
DOWN
SET UP
SELECT
SELECT
SELECT
SHIFT
+
UP+DOWN
SHIFT
+
UP+DOWN
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
EXECUTE
SAVE/LOAD
EXIT
EXECUTE
SAVE/LOAD
EXIT
EXECUTE
Press <SELECT>to select a menu number.
Press <SAVE/LOAD> to select a submenu.
Use <UP> or <DOWN> to select a set value or
an operation.
Use <EXECUTE> to confirm an entry.
No.
Menu.item
Light.
Settings.and.operations
7-segment.display.(display.and.selection)
indication
1
1
2
Set camera number
-
-
Camera number (1 to 19)
Scene files (1 to 4)
Scene files (1 to 4)
User files (1 to 3)
User files (1 to 3)
Lens files (1 to 32)
Lens files (1 to 32)
-
1
1
1
1
1
1
1
-
*
Save scene file to/load scene file
from memory card
ND
CC
ND
CC
ND
CC
ND
CC
Save to memory card
Load from memory card
Save to memory card
Load from memory card
Save to memory card
Load from memory card
Save to memory card
Load from memory card
3
4
5
Save user file to/load user file
from memory card
Save lens file to/load lens file
from memory card
Save ROP configuration file to/
load ROP configuration file from
memory card
-
-
1
6
7
8
9
Format memory card
-
-
-
-
-
*
1
*
Select/set flare and pedestal
-
FLARE/PED (FL/PE)
FL
1
Set buzzer (beep/Call)
-
-
Enable/disable buzzer (on/off)
3 levels (bright/intermediate/low)
3 levels (bright/intermediate/low)
on
*
Set display brightness (LED/7-
segment display)
ND
CC
LED
Bright
Bright
7-segment display
10
11
12
13
14
15
16
17
For future use.
Initialize settings
Confirm version
-
ND
CC
SHT
-
-
-
-
-
-
-
-
-
Display version No (first digits)
Displays the first 3 digits
Version No (middle digits)
Displays the middle 2 digits
Version No (last digits)
Displays the last 3 digits
18
19
Save unit data to memory card
Upgrade software
-
-
-
-
-
1
These functions are controlled by Save ROP configuration file to/load ROP configuration file from memory card
These functions are initialized when you perform settings initialization.
*
„„Files.stored.on.a.memory.card
In setup mode, the following files are saved to or loaded from a memory card by the unit. The fixed file names assigned by the unit must not be changed
on a computer. If the file names are changed, they can no longer be processed by the unit.
Files.stored.on.a.memory.card
Scene file
Filename
SCENE1.BIN to SCENE4.BIN
USER1.BIN to USER3.BIN
LENS01.BIN to LENS32.BIN
ROP_OPE.BIN
User file
Lens file
ROP configuration file
Unit data file
ROP_INFO.BIN
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup.Mode.Operations
<Note>
2..Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
Menu numbers 10 to 15 are for future use.
ND
CC
SHT
SYNC
1..Set.camera.number
M.GAIN
M.PED
1..Open.setup.mode.and.check.that.menu.number.[1].is.
displayed..If.a.menu.number.other.than.[1].appears,.
press.<SELECT>.to.select.menu.number.[1].
Press to select the camera number
IRIS
To save a file to file no. 2 on the memory card
UP
ND
CC
SHT
SYNC
CAMERA
10-19
M.GAIN
M.PED
3..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
DATA
SET
• Do not remove a memory card that is being accessed.
ND
CC
SHT
SYNC
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
M.GAIN
M.PED
DOWN
SET UP
SELECT
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
EXECUTE
IRIS
Press to exit setup mode
(hold down)
Press to select the
menu number
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
Press to confirm the camera number
• [E02] is displayed if the save operation to the memory card fails.
(→page 13)
2..Press.<UP>.or.<DOWN>.to.select.a.camera.number.and.
press.<EXECUTE>.to.confirm.the.selection.
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a scene file with the same name as the one
you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>.(→page 13)
ND
CC
SHT
SYNC
M.GAIN
M.PED
IRIS
To select camera number 2
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
• Camera numbers become available after exiting setup mode.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
2-2.Load.scene.file.from.memory.card
Scene file data loaded from the memory card is returned to the
operating status. (It is not returned to scene files 1 to 4. To return the
data to scene files 1 to 4, exit setup mode and store the data in one of
scene files 1 to 4. For details, refer to <Basics>, the instruction manual.)
2..Save.scene.file.to/load.scene.file.from.memory.card
Current operating status data is saved as a scene file to the memory
card.
1..Press.<SAVE/LOAD>.to.select.[CC].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
Press.<SELECT>to.select.menu.number.[2].
Select file number,
ND
CC
SHT
SYNC
Save file indication
Load file indication
Select y (Select)/
n (Cancel)
M.GAIN
M.PED
UP
ND
CC
SHT
SYNC
CAMERA
10-19
M.GAIN
M.PED
IRIS
DATA
SET
2..Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
DOWN
SET UP
SELECT
ND
CC
SHT
SYNC
SHIFT
+
UP+DOWN
M.GAIN
M.PED
SAVE/LOAD
EXIT
EXECUTE
Press to save/load
Press to confirm
Press to exit setup mode
(hold down)
Press to select the
menu number
IRIS
To load file no. 2 from the memory card
2-1.Save.scene.file.to.memory.card
3..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
1..Press.<SAVE/LOAD>.to.select.[ND].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
• Do not remove a memory card that is being accessed.
[CC] (load).
ND
CC
SHT
SYNC
ND
CC
SHT
SYNC
M.GAIN
M.PED
M.GAIN
M.PED
IRIS
IRIS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup.Mode.Operations. (continued)
• To cancel loading, select [n] and press <EXECUTE>.
• The file is loaded from the memory card and [Fin] appears when
loading ends.
• [E02] is displayed if the load operation from the memory card fails.
(→page 13)
• [E01] is displayed when a user file with the same name as the one
you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>.(→page 13)
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
3-2.Load.user.file.from.memory.card
User file data loaded from the memory card is returned to the operating
status. (It is not returned to user files 1 to 3. To return the data to user
files 1 to 3, exit setup mode and store the data in one of user files 1 to 3.
For details, refer to <Operations>, the instruction manual.)
3.Saving.user.files.to/loading.user.files.from.memory.card
Press.<SELECT>to.select.menu.number.[3].
Select file number,
Select y (Select)/
n (Cancel)
1..Press.<SAVE/LOAD>.to.select.[CC].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
Save file indication
Load file indication
ND
CC
SHT
SYNC
UP
ND
CC
SHT
SYNC
CAMERA
10-19
M.GAIN
M.PED
M.GAIN
M.PED
DATA
SET
No.
IRIS
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
DOWN
SET UP
SELECT
2..Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
EXECUTE
ND
CC
SHT
SYNC
Press to save/load
Press to confirm
M.GAIN
M.PED
Press to exit setup mode
(hold down)
Press to select the
menu number
IRIS
3-1.Save.user.file.to.memory.card
To load file no. 2 from the memory card
Current operating status data is saved as a user file to the memory card.
1..Press.<SAVE/LOAD>.to.select.[ND].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
3..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Do not remove a memory card that is being accessed.
ND
CC
SHT
SYNC
ND
CC
SHT
SYNC
M.GAIN
M.PED
M.GAIN
M.PED
IRIS
IRIS
2..Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
• To cancel loading, select [n] and press <EXECUTE>.
• The file is loaded from the memory card and [Fin] appears when
loading ends.
• [E02] is displayed if the load operation from the memory card fails.
(→page 13)
ND
CC
SHT
SYNC
M.GAIN
M.PED
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
IRIS
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
To save a file to file no. 2 on the memory card
3..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Do not remove a memory card that is being accessed.
ND
CC
SHT
SYNC
M.GAIN
M.PED
IRIS
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
• [E02] is displayed if the save operation to the memory card fails.
(→page 13)
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup.Mode.Operations. (continued)
4-2.Load.lens.file.from.memory.card
4.Save.lens.file.to/load.lens.file.from.memory.card
1..Press.<SAVE/LOAD>.to.select.[CC].
• Each press of <SAVE/LOAD> toggles it between [ND] (Save) and
[CC] (Load).
Press.<SELECT>to.select.menu.number.[4].
Select file number,
Save file indication
Load file indication
Select y (Select)/
n (Cancel)
ND
CC
SHT
SYNC
M.GAIN
M.PED
UP
ND
CC
SHT
SYNC
CAMERA
10-19
M.GAIN
M.PED
DATA
SET
IRIS
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
2..Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
DOWN
SET UP
SELECT
SHIFT
+
UP+DOWN
ND
CC
SHT
SYNC
SAVE/LOAD
EXIT
EXECUTE
M.GAIN
M.PED
Press to save/load
Press to confirm
Press to exit setup mode
(hold down)
Press to select the
menu number
IRIS
To load file no. 2 from the memory card
4-1.Save.lens.file.to.memory.card
1..Press.<SAVE/LOAD>.to.select.[ND].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
3..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
[CC] (load).
• Do not remove a memory card that is being accessed.
ND
CC
SHT
SYNC
ND
CC
SHT
SYNC
M.GAIN
M.PED
M.GAIN
M.PED
IRIS
IRIS
2..Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
• To cancel loading, select [n] and press <EXECUTE>.
• The file is loaded from the memory card and [Fin] appears when
loading ends.
• [E02] is displayed if the load operation from the memory card fails.
(→page 13)
ND
CC
SHT
SYNC
M.GAIN
M.PED
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
• [E04] is displayed when the lens file is off.
IRIS
• To exit setup mode, hold down <EXIT> for about 2 seconds.
To save a file to file no. 2 on the memory card
• To make other settings, press <SELECT> to select a menu number.
3..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
5.Save.ROP.configuration.file.to/load.ROP.
configuration.file.from.memory.card
• Do not remove a memory card that is being accessed.
ND
CC
SHT
SYNC
Press.<SELECT>to.select.menu.number.[5].
M.GAIN
M.PED
Save file indication
Load file indication
Select y (Select)/
n (Cancel)
UP
ND
CC
SHT
SYNC
CAMERA
10-19
IRIS
M.GAIN
M.PED
DATA
SET
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
DOWN
SET UP
• [E02] is displayed if the save operation to the memory card fails.
(→page 13)
SELECT
SHIFT
+
UP+DOWN
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a lens file with the same name as the one
you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>.(→page 13)
SAVE/LOAD
EXIT
EXECUTE
Press to save/load
Press to confirm
Press to exit setup mode
(hold down)
Press to select the
menu number
• [E04] is displayed when the lens file is off.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup.Mode.Operations. (continued)
5-1.Save.ROP.configuration.file.to.memory.card
6.Format.memory.card
1..Press.<SAVE/LOAD>.to.select.[ND].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
1..Press.<SELECT>to.select.menu.number.[6].
Select y (Format)/n (Cancel)
ND
CC
SHT
SYNC
UP
ND
CC
SHT
SYNC
CAMERA
10-19
M.GAIN
M.PED
M.GAIN
M.PED
DATA
SET
IRIS
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
DOWN
SET UP
SELECT
2..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Do not remove a memory card that is being accessed.
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
EXECUTE
ND
CC
SHT
SYNC
Press to confirm
M.GAIN
M.PED
Press to exit setup mode
(hold down)
Press to select the
menu number
IRIS
2..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Card formatting starts.
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
• Do not remove a memory card that is being accessed.
ND
CC
SHT
SYNC
• [E02] is displayed if the save operation to the memory card fails.
(→page 13)
M.GAIN
M.PED
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when an ROP configuration file with the same
name as the one you are attempting to save already exists on the
memory card.
IRIS
• To cancel formatting, select [n] and press <EXECUTE>.
• When the formatting ends, [Fin] appears.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>.(→page 13)
• For details on Save/Load data, refer to page 6.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
7.Select/set.flare.and.pedestal
5-2.Load.ROP.configuration.file.from.memory.card
Press.<SELECT>to.select.menu.number.[7].
Select FL (Flare)/PE (Pedestal)
1..Press.<SAVE/LOAD>.to.select.[CC].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
UP
ND
CC
SHT
SYNC
CAMERA
10-19
ND
CC
SHT
SYNC
M.GAIN
M.PED
M.GAIN
M.PED
DATA
SET
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
IRIS
DOWN
SET UP
SELECT
SHIFT
+
UP+DOWN
2..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
SAVE/LOAD
EXIT
EXECUTE
<EXECUTE>.to.confirm.the.selection.
Press to confirm
• The file is loaded from the memory card and [Fin] appears when
loading ends. A few seconds later, the unit is restarted.
• Do not remove a memory card that is being accessed.
Press to exit setup mode
(hold down)
Press to select the
menu number
ND
CC
SHT
SYNC
M.GAIN
M.PED
7-1.Set.flare
Press.<UP>.or.<DOWN>.to.select.[FL].and.press.
<EXECUTE>.to.confirm.the.selection.
IRIS
ND
CC
SHT
SYNC
M.GAIN
M.PED
• To cancel loading, select [n] and press <EXECUTE>.
• [E02] is displayed if the load operation from the memory card fails.
(→page 13)
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
IRIS
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup.Mode.Operations. (continued)
7-2.Set.pedestal
9-1.Set.LED.brightness
Press.<UP>.or.<DOWN>.to.select.[PE].and.press.
1..Press.<SAVE/LOAD>.to.select.[ND].and.press.
<EXECUTE>.to.confirm.the.selection.
<EXECUTE>.to.confirm.the.selection.
• Each press of <SAVE/LOAD> toggles between [ND] (LED display
ND
CC
SHT
SYNC
M.GAIN
M.PED
brightness) and [CC] (7-segment display brightness).
ND
CC
SHT
SYNC
M.GAIN
M.PED
IRIS
IRIS
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
2..Press.<UP>.or.<DOWN>.to.select.LED.display.brightness.
and.press.<EXECUTE>.to.confirm.the.selection.
8..Set.buzzer.(beep/call.tone)
ND
CC
SHT
SYNC
1..Press.<SELECT>to.select.menu.number.[8].
M.GAIN
M.PED
Select on/off
UP
ND
CC
SHT
SYNC
CAMERA
10-19
IRIS
M.GAIN
M.PED
DATA
SET
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
DOWN
SET UP
9-2.Set.7-segment.display.brightness
SELECT
SHIFT
+
UP+DOWN
1..Press.<SAVE/LOAD>.to.select.[CC].and.press.
<EXECUTE>.to.confirm.the.selection.
SAVE/LOAD
EXIT
EXECUTE
• Each press of <SAVE/LOAD> toggles between [ND] (LED display
Press to confirm
brightness) and [CC] (7-segment display brightness).
ND
CC
SHT
SYNC
Press to exit setup mode
(hold down)
Press to select the
menu number
M.GAIN
M.PED
2..Press.<UP>.or.<DOWN>.to.select.[on].and.press.
<EXECUTE>.to.confirm.the.selection.
IRIS
ND
CC
SHT
SYNC
M.GAIN
M.PED
2..Press.<UP>.or.<DOWN>.to.select.7-segment.display.
brightness.and.press.<EXECUTE>.to.confirm.the.
selection.
ND
CC
SHT
SYNC
IRIS
M.GAIN
M.PED
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
IRIS
9.Display.brightness.setting.(LED/7-segment.display)
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
Press.<SELECT>to.select.menu.number.[9].
LED display brightness
Adjust brightness
7-segment display brightness
Menu.numbers.10.to.15.are.for.future.use.
UP
ND
CC
SHT
SYNC
CAMERA
10-19
M.GAIN
M.PED
16.Initialize.settings
DATA
SET
<Note>
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
When settings are initialized, the unit is automatically restarted.For
details on what settings are initialized, refer to page 6
DOWN
SET UP
SELECT
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
EXECUTE
1..Press.<SELECT>to.select.menu.number.[16].
Select y (Initialize)/n (Cancel)
LED/7-segment display switch
Press to confirm
UP
ND
CC
SHT
SYNC
CAMERA
10-19
Press to exit setup mode
(hold down)
Press to select the
menu number
M.GAIN
M.PED
DATA
SET
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
DOWN
SET UP
SELECT
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
EXECUTE
Press to confirm
Press to exit setup mode
(hold down)
Press to select the
menu number
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup.Mode.Operations. (continued)
• [E02] is displayed if the save operation to the memory card fails.
(→page 13)
2..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• After confirmation, unit settings are initialized and it is automatically
restarted.
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a unit data file with the same name as the
one you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>. (→page 13)
ND
CC
SHT
SYNC
M.GAIN
M.PED
IRIS
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
• To cancel initializing, select [n] and press <EXECUTE>.
19.Software.upgrade
17.Confirm.version
For details on software upgrades, refer to "Software upgrades"(→page
3).
Press.<SELECT>to.select.menu.number.[17].
• The version information is displayed.
• Press <SAVE/LOAD> to show the 8-digit version number split up in 3,
2 and 3 digits.
1..Press.<SELECT>to.select.menu.number.[19].
Select y (Upgrade)
Display digit indication (first 3 digits)
Display digit indication (middle 2 digit)
Display digit indication (last 3 digits)
UP
ND
CC
SHT
SYNC
CAMERA
10-19
M.GAIN
M.PED
DATA
SET
UP
ND
CC
SHT
SYNC
CAMERA
10-19
M.GAIN
M.PED
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
DATA
SET
DOWN
SET UP
SELECT
SHIFT
+
UP+DOWN
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
SAVE/LOAD
EXIT
EXECUTE
DOWN
SET UP
SELECT
SHIFT
+
UP+DOWN
Press to confirm
SAVE/LOAD
EXIT
EXECUTE
Press to exit setup mode
(hold down)
Press to select the
menu number
Press to switch display
digits
Press to select the menu number
2..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
Press to exit setup mode (hold down)
• Upgrading starts.
ND
CC
SHT
SYNC
• To exit setup mode, hold down <EXIT> for about 2 seconds.
M.GAIN
M.PED
• To make other settings, press <SELECT> to select a menu number.
18.Save.unit.data.to.memory.card
IRIS
This functions are used by the manufacturer during maintenance.
1..Press.<SELECT>to.select.menu.number.[18].
• When the upgrade ends, [Fin] appears.
Select y (Save)/n (Cancel)
<Note>
UP
ND
CC
SHT
SYNC
CAMERA
10-19
If the upgrade fails for some reason, <SHIFT> may start to flash after
the restart. If this happens, perform the upgrade process again.
M.GAIN
M.PED
DATA
SET
No.
IRIS
DISPLAY SELECT
ND/CC M.GAIN/M.PED SHUTTER
DOWN
SET UP
SELECT
SHIFT
+
UP+DOWN
SAVE/LOAD
EXIT
EXECUTE
Press to confirm
Press to exit setup mode
(hold down)
Press to select the
menu number
2..Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
ND
CC
SHT
SYNC
M.GAIN
M.PED
IRIS
• The file is saved to the memory card and [Fin] appears when saving
ends.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup.Mode.Operations. (continued)
Error.messages.in.setup.mode
Error.No.
Error.data
E01
E02
A file with the same name already exists. Select [y]
to overwrite.
An error occurred on the memory card.
• Check if a file with the same name already exists.
• Check if the memory card is write protected.
• Check if there is any free space left on the P2 card.
E03
E04
A memory card has not been inserted.
• A communication error occurred. Check the
connected equipment.
• The lens file is off.
E05
An error occurred. Start over from the beginning.
„„When.a.file.with.the.same.name.exists.on.the.memory.
card
[E01] is displayed when a file with the same name as the one you are
attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and press
<EXECUTE>.
„„When.E02.to.E05.are.displayed
Press <EXECUTE> to close the error message. Then perform the
operation again.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ROP.menu.operations
ROP.menus.that.can.be.operated.on.the.unit
Operating.ROP.menus
The unit can access the picture monitor on a CCU to control the ROP
menu (REMOTE OPERATION MENU).
„„Basic.menu.operations
1..Hold.down.<CHARA/MENU>.for.2.seconds.
The [REMOTE OPERATION MENU] appears. (The cursor appears at
the beginning of the first line.)
„„Opening.menus.and.menu.configuration
Hold down <CHARA/MENU> for about 2 seconds to
open [REMOTE OPERATION MENU]. To close
Cursor
CHARA
[REMOTE OPERATION MENU], hold down
→
＊ ＲＥＭＯＴＥ ＯＰＥＲＡＴＩＯＮ ＭＥＮＵ ＊
<CHARA/MENU> for about 2 seconds.
MENU
ＳＨＡＤＩＮＧ（ＷＨＩＴＥ ）
ＰＥＤＥＳＴＡＬ／ＦＬＡＲＥ／ＧＡＩＮ
ＧＡＭＭＡ／ＢＬＡＣＫ ＧＡＭＭＡ
ＣＩＮＥＭＡ ＧＡＭＭＡ
ＫＮＥＥ／ＷＨＩＴＥ ＣＬＩＰ
ＭＡＴＲＩＸ
CHARA
MENU
SELECT
ＨＤ ＤＴＬ／ＳＫＩＮ ＤＴＬ
ＳＤ ＤＥＴＡＩＬ
ＳＹＳＴＥＭ
Use <SELECT> to select the menu.
SELECT
REMOTE OPERATION MENU
SHADING(WHITE)
PEDESTAL/FLARE/GAIN
GAMMA/BLACK GAMMA
CINEMA GAMMA
KNEE/WHITE CLIP
MATRIX
ＦＵＮＣＴＩＯＮ
ＬＥＮＳ ＦＩＬＥ／ＥＤＩＴ
2..Turn.<SELECT>.one.click.clockwise.to.move.the.cursor..
Cursor
＊ ＲＥＭＯＴＥ ＯＰＥＲＡＴＩＯＮ ＭＥＮＵ ＊
→
ＳＨＡＤＩＮＧ（ＷＨＩＴＥ ）
ＰＥＤＥＳＴＡＬ／ＦＬＡＲＥ／ＧＡＩＮ
ＧＡＭＭＡ／ＢＬＡＣＫ ＧＡＭＭＡ
ＣＩＮＥＭＡ ＧＡＭＭＡ
ＫＮＥＥ／ＷＨＩＴＥ ＣＬＩＰ
ＭＡＴＲＩＸ
CHARA
MENU
HD DTL/SKIN DTL
SD DETAIL
ＨＤ ＤＴＬ／ＳＫＩＮ ＤＴＬ
ＳＤ ＤＥＴＡＩＬ
ＳＹＳＴＥＭ
ＦＵＮＣＴＩＯＮ
ＬＥＮＳ ＦＩＬＥ／ＥＤＩＴ
SELECT
SYSTEM
FUNCTION
LENS FILE/EDIT
3..Press.<SELECT>to.select.a.menu.
The [SHADING(WHITE)] menu appears.
Menus cannot be displayed when any of the following messages appear
on the picture monitor.
In this state (when the cursor is in the menu title), press <SELECT> to
return to the next higher menu ([ROP MENU]).
• WARNING message
• AUTO message
• STATUS message
If any of these messages appear, you can hold down <CHARA/MENU>
to delete them and resume operation.
→
＊＊ ＳＨＡＤＩＮＧ（ ＷＨＩＴＥ ） ＊＊
ＷＨＩＴＥ ＳＨＡＤＩＮＧ ＳＷＩＴＣＨ
CHARA
MENU
ＯＮ
ＨＳＡＷ ＨＰＲＡ ＶＳＡＷ ＶＰＡＲＡ
０ ０ ０ ０
０ ０ ０ ０
０ ０ ０ ０
Ｒ
Ｇ
Ｂ
When camera power <HEAD POWER> is Off, only [SYSTEM] can be
selected.
SELECT
4..Turn.<SELECT>.to.move.the.cursor.to.a.setting.and.
press.<SELECT>.
The selected setting flashes allowing you to change the set value.
Flashing
＊＊ ＳＨＡＤＩＮＧ（ ＷＨＩＴＥ ） ＊＊
CHARA
→
ＷＨＩＴＥ ＳＨＡＤＩＮＧ ＳＷＩＴＣＨ
ＯＮ
ＨＳＡＷ ＨＰＲＡ ＶＳＡＷ ＶＰＡＲＡ
０ ０ ０ ０
０ ０ ０ ０
０ ０ ０ ０
MENU
Ｒ
Ｇ
Ｂ
SELECT
<Note>
Turn <SELECT> quickly to change the hundreds place of a set value.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ROP.menu.operations. (continued)
„„Operating.other.menus
When a menu has more than one setting on a line, press <SELECT>
(to confirm) and the cursor [] appears.
Turn <SELECT> right or left to move the cursor to the input area.
Cursor movement
＊＊ ＳＨＡＤＩＮＧ（ ＷＨＩＴＥ ） ＊＊
ＷＨＩＴＥ ＳＨＡＤＩＮＧ ＳＷＩＴＣＨ
ＨＳＡＷ ＨＰＲＡ ＶＳＡＷ ＶＰＡＲＡ
０ ０ ０ ０
ＯＮ
↓
Ｇ
Ｂ
Ｒ
↓
↓
↓
↓
０ ０ ０ ０
０ ０ ０ ０
In a character entry menu, the [] cursor will also appear.
Cursor movement
＊＊ＬＥＮＳ ＦＩＬＥ/ ＥＤＩＴ( １/ ２ ） ＊＊
ＭＯＤＥ
ＬＯＡＤ
ＦＩＬＥ ＮＯ
↓↓↓↓↓↓↓↓
↓ＦＩＬＥ ＮＡＭＥ
ＥＸＥＣＵＴＥ
ＮＯ？
When the cursor is at the beginning of a menu, press <SELECT> to
confirm to turn the cursor into [] to continue selecting menu items.
＊＊ ＳＨＡＤＩＮＧ（ ＷＨＩＴＥ ） ＊＊
ＷＨＩＴＥ ＳＨＡＤＩＮＧ ＳＷＩＴＣＨ
ＯＮ
ＨＳＡＷ ＨＰＲＡ ＶＳＡＷ ＶＰＡＲＡ
０ ０ ０ ０
０ ０ ０ ０
０ ０ ０ ０
↓
Ｇ
Ｂ
Ｒ
＊＊ ＳＨＡＤＩＮＧ（ ＷＨＩＴＥ ） ＊＊
ＷＨＩＴＥ ＳＨＡＤＩＮＧ ＳＷＩＴＣＨ
ＯＮ
ＨＳＡＷ ＨＰＲＡ ＶＳＡＷ ＶＰＡＲＡ
０ ０ ０ ０
０ ０ ０ ０
０ ０ ０ ０
→
Ｒ
Ｇ
Ｂ
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ROP.menu.setting
The following describes [ROP MENU] settings.
PEDESTAL/FLARE/GAIN
SHADING(WHITE)
→
＊＊ ＰＥＤＥＳＴＡＬ／ＦＬＡＲＥ／ＧＡＩＮ ＊＊
ＦＬＡＲＥ ＳＷＩＴＣＨ
ＯＮ
→
＊＊ ＳＨＡＤＩＮＧ（ ＷＨＩＴＥ ） ＊＊
ＷＨＩＴＥ ＳＨＡＤＩＮＧ ＳＷＩＴＣＨ
Ｒ
Ｇ
Ｂ
０
０
０
ＯＮ
ＰＥＤＥＳＴＡＬ
ＦＬＡＲＥ
ＧＡＩＮ
０
０
０
０
０
ＨＳＡＷ ＨＰＡＲＡ ＶＳＡＷ ＶＰＡＲＡ
０ ０ ０ ０
０ ０ ０ ０
０ ０ ０ ０
Ｒ
Ｇ
Ｂ
ＭＡＳＴＥＲ ＰＥＤＥＳＴＡＬ
０
(
indicates factory default settings.)
Item
Display
Function
(
indicates factory default settings.)
.Function
FLARE.SWITCH
OFF Set to On to adjust flare
ON correction amount.
Item
Display
Flare correction controls the
increase in pedestal level in
proportion to light intensity.
WHITE.SHADING.
SWITCH
OFF Enables/disables white shading.
ON
MASTER.
PEDESTAL
-99 Indicates set master pedestal
H.SAW.R
H.SAW.G
H.SAW.B
H.PARA.R
H.PARA.G
H.PARA.B
V.SAW.R
V.SAW.G
V.SAW.B
V.PARA.R
V.PARA.G
V.PARA.B
-100 Performs sawtooth wave
׀ 0
value. (Settings cannot be
made.)
׀ 0
׀ correction of white screen
images in the horizontal
direction.
׀ 99
100
PEDESTAL.R
-800 Amount by which the level is
-100 Performs parabola correction
׀ 0
׀ increased or decreased relative
to the G pedestal to adjust the
black balance. When the auto
׀ 0
of white screen images in the
horizontal direction.
׀ 800 black balance is achieved, 0 is
100
set as the adjustment value.
PEDESTAL.G
PEDESTAL.B
-800 Adjusts the amount of G
-100 Performs sawtooth wave
׀ 0
pedestal offset from master
pedestal.
׀ 0
correction of white screen
images in the vertical direction.
׀ ׀ 800
100
-800 Amount by which the level is
-100 Performs parabola correction
׀ 0
׀ increased or decreased relative
to the G pedestal to adjust the
black balance. When the auto
׀ 0
of white screen images in the
vertical direction.
׀ 800 black balance is achieved, 0 is
100
set as the adjustment value.
FLARE.R
FLARE.G
FLARE.B
GAIN.R
-100 Adjusts the amount of R FLARE
׀ 0
correction.
׀ 100
-100 Adjusts the amount of G FLARE
׀ 0
correction
׀ 100
-100 Adjusts the amount of B FLARE
׀ 0
correction
׀ 100
-800 Adjusts the white balance.
׀ 0
׀ Amount by which the R gain has
to be increased or decreased
relative to the G gain level.
800 When the auto white balance
is achieved, 0 is set as the
adjustment value.
GAIN.B
-800 Adjusts the white balance.
׀ 0
׀ Amount by which the B gain has
to be increased or decreased
relative to the G gain level.
800 When auto white balance
is achieved, 0 is set as the
adjustment value.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ROP.menu.setting. (continued)
GAMMA/BLACK.GAMMA
Item
Display
Function
DRS.SWITCH
OFF Turn on for automatic contrast
ON adjustment.
→
＊＊ ＧＡＭＭＡ／ＢＬＡＣＫ ＧＡＭＭＡ ＊＊
This adaptive-type gamma
correction adjusts the gamma
correction to the optimal setting.
ＧＡＭＭＡ ＳＷＩＴＣＨ
ＧＡＭＭＡ
ＯＮ
Ｂ
０
Ｒ
Ｍ
０ ０．４５０
EFFECT.DEPTH
1
׀ 5
Turn on for contrast adjustment.
Higher numbers mean greater
effect.
ＢＬＡＣＫ ＧＡＭＭＡ ＳＷＩＴＣＨ
Ｒ
ＯＦＦ
Ｂ
Ｍ
PRE-
4.0 Turn on to adjust the rising slope
ＢＬＡＣＫ ＧＡＭＭＡ
０
０
０
CORRECTION
4.5 in low-light areas.
ＤＲＳ ＳＷＩＴＣＨ
ＥＦＥＣＴ ＤＥＰＴＨ
ＰＲＥ－ＣＯＲＲＥＣＴＩＯＮ
ＯＦＦ
５
４．５
5.0.
CINEMA.GAMMA
<Note>
(
indicates factory default settings.)
• The settings in this menu are not available when the [CINEMA
GAMMA SWITCH] is set to [OFF].
Item
GAMMA.SWITCH
Display
Function
OFF Turn on to correct the gamma.
ON Gamma provides the signal
level of the TV video signal
→
＊＊ ＣＩＮＥＭＡ ＧＡＭＭＡ ＊＊
ＣＩＮＥＭＡ ＧＡＭＭＡ ＳＷＩＴＣＨ
ＣＩＮＥＭＡ ＴＹＰＥ
ＣＩＮＥＭＡ ＧＡＭＭＡ ＳＥＬ
ＢＬＡＣＫ ＳＴＲＥＴＣＨ ＬＥＶＥＬ
ＤＹＮＡＭＩＣ ＬＥＶＥＬ
ＯＦＦ
ＶＩＤＥＯ
ＶＩＤＥＯ ＲＥＣ
with characteristics that are the
reverse of those for video signal
input and light intensity level.
＿
０
２００％
GAMMA.R
zVIDEO REC
Adjusts R gamma correction
-75 relative to M gamma.
|
0
ＫＮＥＥ ＰＯＩＮＴ
ＫＮＥＥ ＳＬＯＰＥ
３０
１５０％
|
75
zFILMLIKE1 to 3
-60
|
60
(
indicates factory default settings.)
GAMMA.M
GAMMA.B
0.300 Adjusts the master gamma.
׀ 0.450
׀ Item
Display
Function
CINEMA.GAMMA.
SWITCH
OFF Enables or disables cinema
ON gamma mode.
0.750
CINEMA.TYPE
VIDEO Switches between cinema
FILM gamma characteristics for video
and those for film
zVIDEO REC
Adjusts B gamma correction
-75 relative to M gamma.
|
0
|
75
CINEMA.GAMMA. zWhen [CINEMA Sets cinema gamma
SEL
TYPE] is set to
[VIDEO]
characteristics for video.
VIDEO_REC
FILMLIKE1
FILMLIKE2
zFILMLIKE1 to 3
-60
|
60
FILMLIKE3
zWhen [CINEMA
TYPE] is set to
[FILM]
BLACK.GAMMA.
SWITCH
OFF Turn this switch on to correct the
ON black gamma.
It changes the amplification rate
FILM_REC.(fixed)
.
of the video signal in low light
intensity areas.
BLACK.
STRETCH.
LEVEL
0
׀ This function is available only
when the [CINEMA GAMMA
BLACK.GAMMA.
R
-20.(black. Corrects the black gamma
compression) curve R.
30. SWITCH] is set to [ON] and
[CINEMA TYPE] is set to [FILM].
׀ 0
׀ DYNAMIC.
LEVEL
200%/300%/ Sets the dynamic range
400%/500%. This function is available only
when [CINEMA TYPE] is set to
[FILM].
20.(black.
expansion)
1
KNEE.POINT
30 Sets the master knee point.
*
BLACK.GAMMA.
M
-32.(black. Corrects the black gamma.
compression)
׀ Turn the Select dial clockwise to
90 increase the knee point value.
׀ 0
׀ (The numbers decrease.)
1
*
KNEE.SLOPE
150%/200%/ Sets the master knee slope.
250%/300%/
350%/400%/
32.(black.
expansion)
450%/500%/
550%/600%.
BLACK.GAMMA.
B
-20.(black. Corrects the black gamma
compression) curve B.
׀ 0
׀ 1
When the Knee OFF button <KNEE OFF> is On or when [KNEE
SWITCH] is set to [OFF] in the [KNEE/WHITE CLIP] menu, settings
cannot be changed.
*
20.(black.
expansion)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ROP.menu.setting. (continued)
KNEE/WHITE.CLIP
MATRIX.(1/2)
<Note>
→
＊＊ ＭＡＴＲＩＸ（ １／２ ） ＊＊
ＰＲＥＳＥＴ
• Some settings in this menu are not available when the [CINEMA
GAMMA SWITCH] is set to [ON].
ＮＯＲＭＡＬ
ＯＦＦ
ＭＡＴＲＩＸ ＳＷＩＴＣＨ
→
＊＊ ＫＮＥＥ／ＷＨＩＴＥ ＣＬＩＰ ＊＊
ＫＮＥＥ ＳＷＩＴＣＨ
ＭＥＭＯＲＹ
Ｒ－Ｇ
Ａ
０
０
０
０
０
０
ＯＮ
Ｂ
０
０
Ｒ
Ｍ
Ｒ－Ｂ
Ｇ－Ｒ
Ｇ－Ｂ
Ｂ－Ｒ
Ｂ－Ｇ
ＰＯＩＮＴ
ＳＬＯＰＥ
０ ９５．０％
０
１３０％
ＷＨＩＴＥ ＣＬＩＰ ＳＷＩＴＣＨ
Ｒ
ＯＮ
Ｂ
Ｍ
ＣＬＩＰ
０
１０９％
０
ＨＩ ＣＯＬＯＲ
ＯＦＦ
(
indicates factory default settings.)
Item
Display
Function
PRESET
NORMAL Switches matrix presets.
EBU
NTSC
(
indicates factory default settings.)
Item
Display
Function
MATRIX.SWITCH
MEMORY
OFF Enables or disables saturation
ON and color phase correction.
KNEE.SWITCH
OFF/ON Turn on to adjust the knee slope
and knee point.
OFF Select matrix memory to adjust.
A
B
POINT.R
-20 Sets the R knee point.
׀ 0
׀ .R-G
R-B
G-R
G-B
B-R
B-G
-63 Adjusts the saturation and color
׀ 0
׀ 63
phase of R and G components
in matrix memory.
20.
POINT.M
POINT.B
SLOPE.R
SLOPE.M
SLOPE.B
80.0% Sets the master knee point.
׀ 95.0%
׀ -63 Adjusts the saturation and color
׀ 0
׀ 63
phase of R and B components in
matrix memory.
110.0%.
-20 Sets the B knee point.
׀ 0
׀ -63 Adjusts the saturation and color
׀ 0
׀ 63
phase of G and R components
in matrix memory.
20.
-31 Sets the R knee slope.
׀ 0
׀ -63 Adjusts the saturation and color
׀ 0
׀ 63
phase of G and B components in
matrix memory.
31.
0
׀ Sets the master knee slope.
130
׀ 199
-63 Adjusts the saturation and color
׀ 0
׀ 63
phase of B and R components in
matrix memory.
-31 Sets the B knee slope.
׀ 0
׀ -63 Adjusts the saturation and color
׀ 0
׀ 63
phase of B and G components in
matrix memory.
31.
WHITE.CLIP.
SWITCH
OFF Enables or disables the white
ON clip function.
CLIP.R
-15 Sets the R white clip function.
׀ 0
׀ 15
CLIP.M
CLIP.B
80% Sets the master white clip
׀ function.
109%
-15 Sets the B white clip function.
׀ 0
׀ 15
HI.COLOR
OFF Turn on to improve the color
ON reproducibility in the high-
brightness areas.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ROP.menu.setting. (continued)
MATRIX.(2/2)
HD.DTL/SKIN.DTL.(1/2)
→
＊＊ ＭＡＴＲＩＸ（ ２／２ ） ＊＊
→＊＊ ＨＤ ＤＴＬ／ＳＫＩＮ ＤＴＬ（ １／２ ） ＊＊
１２ＡＸＩＳ ＭＥＭＯＲＹ
ＳＡＴ ＰＨＡＳＥ
Ａ
ＤＥＴＡＩＬ ＳＷＩＴＣＨ
Ｖ ＤＥＴＡＩＬ
Ｈ ＤＥＴＡＩＬ
ＯＮ
２０
２０
１０
１７．３
８％
ＳＡＴ ＰＨＡＳＥ
＿
Ｇ
０
０
０
０
０
０
０
０
０
０
０
０
Ｇ
Ｃｙ
Ｂ
０
０
０
０
０
０
０
０
０
０
０
０
＿
Ｃｙ
Ｂ
Ｃｙ
ＣＲＩＳＰ
＿
Ｂ
Ｍｇ
ＰＥＡＫ ＦＲＥＱＵＥＮＣＹ
ＬＥＶＥＬ ＤＥＰＥＮＤＥＮＴ
ＤＡＲＫ ＤＥＴＡＩＬ
ＳＯＵＲＣＥ
ＣＬＩＰ
ＫＮＥＥ ＤＥＴＡＩＬ
ＧＡＩＮ
＿
Ｍｇ
Ｒ
Ｍｇ
Ｒ
＿
Ｒ
Ｙｅ
０
＿
Ｙｅ
Ｙｅ
Ｇ
（Ｒ＋Ｇ）／２
（ － ） ０
０
（ ＋ ） ０
（ ＋ ） ０
（ － ） ０
(
indicates factory default settings.)
(
indicates factory default settings.)
Item
12AXIS.
Display
Function
Item
Display
Function
OFF Select 12 AXIS memory to
DETAIL.SWITCH
OFF Enables or disables the HD
MEMORY
A
B
adjust.
ON DETAIL effect.
V.DETAIL
0
׀ Adjusts the level of vertical
detail.
G.SAT
-63 Adjusts the saturation of color
׀ 0
׀ components in 12 AXIS matrix
memory.
• Not available when [12 AXIS
MEMORY] is set to [OFF].
20
׀ 63
G_Cy.SAT
Cy.SAT
Cy_B.SAT
B.SAT
63
H.DETAIL
CRISP
0
׀ 20
׀ Adjusts the level of horizontal
detail.
B_Mg.SAT
Mg.SAT
63
Mg_R.SAT
R.SAT
0
׀ Sets the maximum amplitude of
the very faint noise components
10 that are removed from detail
R_Ye.SAT
Ye.SAT
׀ components.
63
Ye_G.SAT
G.PHASE
PEAK.
FREQUENCY
12.4/12.5/ Selects the contour correction
12.7/12.9/ frequency band (boost frequency
13.0/13.3/ or peak frequency). It changes
13.6/13.9/ the contour width.
14.2/14.6/
-63 Adjusts the color phase of color
׀ 0
components in 12 AXIS matrix
memory.
G_Cy.PHASE
Cy.PHASE
׀ 63
• Not available when [12 AXIS
MEMORY] is set to [OFF].
Cy_B.PHASE
B.PHASE
15.0/15.5/
16.1/16.7/
17.3/18.0/
18.6/18.8/
19.0/19.2/
19.5/19.9/
B_Mg.PHASE
Mg.PHASE
Mg_R.PHASE
R.PHASE
20.3/20.9/
21.5/22.4/
23.6/25.4/
28.6/37.1
R_Ye.PHASE
Ye.PHASE
Ye_G.PHASE
LEVEL.
0% Lowers the detail in dark areas.
DEPENDENT
׀ 8%
׀ It adjusts the level.
30%
DARK.DETAIL
SOURCE
0
׀ 7
Boosts the detail in dark areas.
(R+G)/2 Selects the source signals for
(G+B)/2 creating the detail components.
(2G+R+B)/4
(3G+R)/4
R
G
+CLIP
0
׀ Limits the length of the
overshoot areas of the detail
63 edge components.
-CLIP
0
׀ Limits the length of the
undershoot areas of the detail
63 edge components.
KNEE.DETAIL
0
׀ Enhances knee detail.
39
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ROP.menu.setting. (continued)
Item
Display
Function
Item
Display
Function
+GAIN
-31 Changes the detail gain level in
MEM.A.WIDTH
0
׀ Expands the width of skin tone
areas in memory bank A in a
׀ 0
+ (up) direction
255 range from 0 to 255.
׀ 31
MEM.A.SATU
MEM.B.CRISP
0
׀ Changes the saturation of skin
tone areas in memory bank A in
-GAIN
-31 Changes the detail gain level in -
׀ 0
׀ 31
255 a range of 0 to 255.
(down) direction
-63 Removes very faint noise
׀ 0
components from detail
components in skin tone areas
in memory bank B.
׀ 63
MEM.B.PHASE
0
׀ Changes the color phase of skin
tone areas in memory bank B in
HD.DTL/SKIN.DTL.(2/2)
359 a range of 0 to 359 on a vector
→
＊＊ ＨＤ ＤＴＬ／ＳＫＩＮ ＤＴＬ（ ２／２ ） ＊＊
display.
MEM.B.WIDTH
MEM.B.SATU
ZEBRA.SWITCH
0
׀ Expands the width of skin tone
areas in memory bank B in a
ＳＫＩＮ ＤＥＴＡＩＬ ＳＷＩＴＣＨ ＯＦＦ
ＣＵＲＳＯＲ
ＯＮ／ＯＦＦ
ＯＦＦ
Ｈ
９６０
Ｖ
２７０
ＮＯ�
Ａ
255 range from 0 to 255.
0
׀ Changes the saturation of skin
tone areas in memory bank B in
ＳＫＩＮ ＧＥＴ
ＭＥＭＯＲＹ ＳＥＬＥＣＴ
ＣＲＩＳＰ
ＰＨＡＳＥ
ＷＩＤＴＨ ＳＡＴＵ
255 a range from 0 to 255.
Ａ
Ｂ
０
０
０
０
０
０
０
０
OFF Adds a zebra pattern to the
A
B
Y signals of the PM output to
make areas subject to skin tone
ＺＥＢＲＡ ＳＷＩＴＣＨ
ＥＦＦＥＣＴ ＭＥＭＯＲＹ
ＯＦＦ
Ａ＋Ｂ
A+B detail effects easily visible.
EFFECT.
MEMORY
A
B
Selects the memory bank to
which skin tone detail effects will
A+B be added.
(
indicates factory default settings.)
Item
Display
Function
SD.DETAIL
SKIN.DETAIL.
SWITCH
OFF Enables or disables control of
ON skin tone detail in HDTV video
output.
→
＊＊ ＳＤ ＤＥＴＡＩＬ ＊＊
CURSOR
OFF Enables or disables the position
ON cursor that obtains the saturation
and color phase information for
controlling skin tone detail.
ＤＥＴＡＩＬ ＳＷＩＴＣＨ
Ｖ ＤＥＴＡＩＬ
Ｈ ＤＥＴＡＩＬ
ＣＲＩＳＰ
ＯＮ
３
５
０
ＰＥＡＫ１
ＰＥＡＫ２
ＬＥＶＥＬ ＤＥＰＥＮＤＥＮＴ
ＤＡＲＫ ＤＥＴＡＩＬ
３．１７Ｍ
ＯＦＦ
５％
POS.H
1
Sets horizontal cursor position.
׀ 960
׀ １
1920
POS.V
1
׀ Sets vertical cursor position.
270
.540
(
indicates factory default settings.)
SKIN.GET
NO? Automatically obtains the
EXECUTE saturation and color phase
CANCEL information from the cursor
position.
Item
Display
Function
DETAIL.SWITCH
ON Enables or disables changes in
OFF contour enhancement (hard/soft)
level of SDTV video output.
NO?:
V.DETAIL
H.DETAIL
0
׀ 3
׀ 63
Adjusts the amount of vertical
detail.
Cancels operation.
EXECUTE:
Automatically obtains
saturation and color phase
information from the cursor
position.
0
׀ Adjusts the amount of horizontal
detail.
CANCEL:
Discards the saturation and
color phase information
obtained from the cursor
position.
5
׀ 63
CRISP
PEAK1
0
׀ Sets the maximum amplitude of
the very faint noise components
MEMORY.
SELECT
A
B
Changes memory locations
for saving the skin tone detail
settings (CRISP, PHASE,
WIDTH and SATURATION).
63 that are removed from detail
components.
1.89M/2.18M/ Selects one of the two contour
2.56M/3.17M/ correction frequency bands
4.0M/5.28M/ (boost frequency or peak
6.75M frequency). Changes the contour
width.
MEM.A.CRISP
MEM.A.PHASE
-63 Removes very faint noise
׀ 0
׀ components from detail
components in skin tone areas
in memory bank A.
63
PEAK2
OFF/1.89M/ Selects one of the two contour
2.18M/2.56M/ correction frequency bands
3.17M/4.00M/ (boost frequency or peak
.5.28M/6.75M frequency). Changes the contour
width.
0
׀ Changes the color phase of skin
tone areas in memory bank A
359 in a range from 0 to 359 on a
vector display.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ROP.menu.setting. (continued)
Item
LEVEL.
DEPENDENT
Display
Function
Item
Display
Function
0
Lowers the detail in dark areas.
It adjusts the level.
HD.COLOR.BAR
FULL Select the color bar signals to be
BARS-1 output from the HD/SD SDI OUT
ARIB connectors and VBS connector
BARS-2 when “BAR” has been selected
BARS-3 on the operation panel of the
BARS-4 ROP.
BARS-5 When they are output in VBS
BARS-6 or SD format, color bars in HD
format are output in the mode
specified with
׀ 5.%
׀ 30.%
DARK.DETAIL
0
׀ 1
׀ 5
DOWNCONVERT MODE.
FULL:
75 % full field color bar
BARS-1:
SYSTEM.(1/2)
Color bar based on the
SMPTE standard
→
＊＊ ＳＹＳＴＥＭ （ １／２ ） ＊＊
ARIB:
ＲＥＴＵＲＮ１
ＲＥＴＵＲＮ２
ＲＥＴＵＲＮ３
ＲＥＴＵＲＮ４
ＲＥＴＵＲＮ・ＤＥＬＡＹ
ＤＯＷＮ ＣＯＮＶＥＲＴ ＭＯＤＥ
ＵＰ ＣＯＮＶＥＲＴ ＭＯＤＥ
ＨＤ ＣＯＬＯＲ ＢＡＲ
ＰＡＴＨＯ
ＨＤ ＳＤＩ１
ＨＤ ＳＤＩ２
ＨＤ ＳＤＩ１
ＨＤ ＳＤＩ２
ＮＯＲＭＡＬ
ＳＣ
ARIB multi-format color bar
BARS-2:
Color bar based on the EIAJ
standard
BARS-3:
Split field color bar
ＳＣ
ＡＲＩＢ
ＯＦＦ
ＰＭ
BARS-4:
75 % full field color bar placed
in an area with a 4:3 aspect
ratio.
ＳＤＩ３－４ ＯＵＴ
(Displayed 40 % gray outside
the area.)
BARS-5:
Color bar based on the
SMPTE standard that is
placed in an area with a 4:3
aspect ratio.
(Displayed 40 % gray outside
the area.)
(
indicates factory default settings.)
Item
Display
Function
RETURN1
HD.SDI1 Sets the input allocations of
HD.SDI2 return signal 1.
VBS
BARS-6:
RETURN2
RETURN3
RETURN4
HD.SDI1 Sets the input allocations of
HD.SDI2 return signal 2.
VBS
Color bar based on the EIAJ
standard that is placed in an
area with a 4:3 aspect ratio.
(Displayed 40 % gray outside
the area.)
HD.SDI1 Sets the input allocations of
HD.SDI2 return signal 3.
VBS
PATHO
OFF Select ON/OFF for the
ON pathological signals.
HD.SDI1 Sets the input allocations of
HD.SDI2 return signal 4.
VBS
SDI3-4.OUT
NORMAL Selects the signals output from
PM the 3rd and 4th HD/SD SDI
signal output connectors on a
CCU.
RETURN.·.
DELAY
NORMAL Selects whether a RET display
SHORT video will be delayed by 1 F
(NORMAL) or by the shortest
possible period (SHORT).
DOWN.
CONVERT.
MODE
SC Selects the down-conversion
SQ system for video output from SD
LB SDI and VBS.
UP.CONVERT.
MODE
SC Selects the up-conversion
SQ system for videos used as SD
LB SDI and VBS return videos.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ROP.menu.setting. (continued)
SYSTEM.(2/2)
Item
Display
Function
MIC1.AMP
-20dB Makes fine adjustments of the
׀ MIC1 gain.
→
＊＊ ＳＹＳＴＥＭ （ ２／２ ） ＊＊
0
׀ (in.1.dB.increments)
ＨＤ Ｈ ＰＨＡＳＥ
ＳＤ Ｈ ＰＨＡＳＥ
ＳＤ－ＨＤ Ｖ
０
０
０Ｈ
20dB
MIC2.GAIN
MIC2.AMP
20dB Makes coarse adjustments of
40dB MIC2 gain.
60dB
-20dB Makes fine adjustments of MIC2
ＧＡＩＮ
ＡＭＰ
׀ gain.
ＭＩＣ１
ＭＩＣ２
６０dB
６０dB
０dB
０dB
0
׀ (in.1.dB.increments)
20dB
FUNCTION
(
indicates factory default settings.)
Item
Display
Function
→
＊＊ ＦＵＮＣＴＩＯＮ ＊＊
HD.H.PHASE
-1099 Adjusts the horizontal phase of
ＡＬＣ ＬＥＢＥＬ
ＡＬＣ ＳＰＥＥＤ
ＡＬＣ ＷＩＮＤＯＷ
ＡＬＣ ＰＥＡＫ
５０
１５
１
׀ 0
׀ HD SDI video for the genlock
reference phase.
６０
1099.(59.94.Hz)
ＡＬＣ ＲＡＮＧＥ
ＮＯＲＭＡＬ
-1319
ＡＳＵ ＳＥＴＵＰ
ＡＳＵ ＲＥＦ ＦＩＬＥ
ＡＳＵ ＭＡＳＴＥＲ ＰＥＤ ＳＥＴ
ＡＳＵ ＦＩＬＴＥＲ
ＯＵＴ ＦＵＬＬ
ＦＡＣＴＯＲＹ
׀ 0
׀ ２．０％
ＲＥＦ
1319.(50Hz)
ＴＡＬＬＹ ＧＵＡＲＤ
ＯＦＦ
SD.H.PHASE
-857 Adjusts SD horizontal sync
׀ phase.
0
׀ (
indicates factory default settings.)
857.(59.94Hz)
Item
Display
Function
ALC.LEVEL
0
׀ 50
׀ Adjusts the auto iris level of the
lens iris.
-863
׀ 0
׀ 100
863.(50Hz)
ALC.SPEED
1
׀ Sets the feedback speed of the
auto iris.
SD-HD.V
0H Set the vertical phase of the
ADVANCE HDTV output in relation to the
0H_SD_DLAY. SDTV output.
0H:
15 Feedback speed drops as the
׀ 25
numbers increase.
Sets the vertical phase to the
same phase.
ADVANCE:
When the field frequency is
59.94 Hz, the phase advance
is 90H.
When the field frequency is 50
Hz, the phase advance is 75H.
0H_SD_DLAY:
ALC.WINDOW
ALC.PEAK
1
׀ 4
Sets the image detection area
window for the auto iris.
0
׀ Sets the ratio between the
average and peak values of auto
60 iris image detection.
׀ 100
The SDTV signals are delayed
and set in-phase with the
HDTV signals.
ALC.RANGE
NORMAL Sets the correction range for
3/4 adjustments of the iris level
2/4 using the IRIS knob to move the
1/4 iris lever <IRIS ( )> in auto
iris mode.
• When the setting of this item
is set to “0H” or “ADVANCE”
while the field frequency is
50 Hz, images in SD format
are delayed by 1 frame + 75
lines only when letterbox is
selected for DOWNCONVERT
MODE.
ASU.SETUP
OUT.FULL Selects the auto setup mode
OUT.EASY setting.
ASU.REF.FILE
FACTORY Selects the file to be referenced
USER1 when auto setup has been
USER2 started.
For the relationship with the
sync phase, refer to Operating
Instructions <Operations and
Settings> of AK-HCU200.
USER3
ASU.MASTER.
PED.SET
0.0% Sets the position where the
׀ master pedestal is to be
2.0% converged when auto setup is
׀ started.
ADVANCE:
. 59.94Hz→90H
. 50Hz→75H
7.5%
MIC1.GAIN
20dB Performs coarse adjustment of
40dB MIC1 gain.
60dB
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ROP.menu.setting. (continued)
Item
Display
Function
LENS.FILE/EDIT.(2/2)
ASU.FILTER
REF Sets the operation of the ND
CURRENT filter when auto setup is started.
→
＊＊ ＬＥＮＳ ＦＩＬＥ／ＥＤＩＴ（ ２／２ ） ＊＊
REF:
ＥＸＴＥＮＤＥＲ
ＦＩＬＥ
Ｘ１．０
The filter stored in the
reference file is used when
operation starts.
CURRENT:
Auto setup starts at the filter
position made prior to startup.
Ｒ
Ｇ
Ｂ
ＦＬＡＲＥ
ＧＡＩＮ
ＨＳＡＷ
－
－
－
－
－
ＨＰＡＲＡ
ＶＳＡＷ
ＶＰＡＲＡ
Ｒ
Ｇ
Ｂ
－
－
－
－
－
－
－
－
－
－
－
－
TALLY.GUARD
OFF At the ON setting, this function
ON disables automatic ASU, AWB,
ABB operation while the tally
is ON.
ＳＴＯＲＥ？
ＣＡＮＣＥＬ？
－
－
(
indicates factory default settings.)
LENS.FILE/EDIT.(1/2)
Item
Display
Function
→
＊＊ ＬＥＮＳ ＦＩＬＥ／ＥＤＩＴ（ １／２ ） ＊＊
EXTENDER
x.1.0 Sets the current magnification of
x.2.0 the lens extender.
ＭＯＤＥ
ＦＩＬＥ ＮＯ
ＬＯＡＤ
ＯＦＦ
FILE
Displays the number and name
of currently loaded lens files.
ＦＩＬＥ ＮＡＭＥ
ＥＸＥＣＵＴＥ
FLARE.R
-100 Sets lens R flare.
׀ 0
ＮＯ？
׀ 100
FLARE.G
FLARE.B
GAIN.R
-100 Sets lens G flare.
׀ 0
׀ 100
(
indicates factory default settings.)
-100 Sets lens B flare.
׀ 0
׀ Item
Display
Function
MODE
LOAD Saves current lens files in the
STORE camera (STORE) or loads
(LOAD) lens files stored in the
camera.
100
-100 Sets lens R gain.
׀ 0
׀ FILE.NO.
zWhen [LOAD]
is selected as
[MODE]
Selects the lens file number.
100
OFF
GAIN.B
-100 Sets lens B gain.
1
׀ ׀ 0
׀ 32
zWhen [STORE]
is selected as
[MODE]
100
R.HSAW
R.HPARA
R.VSAW
R.VPARA
G.HSAW
G.HPARA
G.VSAW
G.VPARA
B.HSAW
B.HPARA
B.VSAW
B.VPARA
STORE?
-100 Sets lens white shading.
1
׀ ׀ 0
׀ . 32
100
FILE.NAME
Up.to.8. Use to enter the file name.
characters • It is disabled when [LOAD] is
selected in [MODE].
Allowable.characters
0.-.9,.A.-.Z,.a.-.z,..
_.(under.bar),..(space)
EXECUTE
YES? Executes processes selected in
NO? MODE.
YES? Saves R/G/B gain, R/G/B flare
NO? and white shading settings to
the displayed file.
CANCEL?
YES? Discards R/G/B gain, R/G/B
NO? flare and white shading settings
and restores the original lens
files.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
C
Camera number ......................................................................................7
CINEMA-GAMMA ................................................................................ 17
Confirm version ................................................................................... 12
E
Error display ........................................................................................ 13
F
Format (memory card) ......................................................................... 10
FUNCTION .......................................................................................... 22
G
GAMMA/BLACK GAMMA .................................................................... 17
H
HD DTL/SKIN DTL ........................................................................ 19, 20
I
Initialize ................................................................................................ 11
K
KNEE/WHITE CLIP ............................................................................. 18
L
Lens file ..................................................................................................9
Load ...............................................................................................9
Save ...............................................................................................9
LENS FILE/EDIT ................................................................................. 23
M
MATRIX ......................................................................................... 18, 19
P
PEDESTAL/FLARE/GAIN ................................................................... 16
R
ROP configuration file .............................................................................9
Load ............................................................................................ 10
Save ............................................................................................ 10
ROP menu
Operation ..................................................................................... 14
Setting ......................................................................................... 16
S
Save unit data ...................................................................................... 12
Scene file ................................................................................................7
Load ...............................................................................................7
Save ...............................................................................................7
SD DETAIL .......................................................................................... 20
Set 7-segment display brightness ...................................................... 11
Set buzzer ........................................................................................... 11
Set display brightness ......................................................................... 11
Set flare ............................................................................................... 10
Set LED display brightness ................................................................ 11
Set pedestal ......................................................................................... 11
Setup mode ............................................................................................4
SHADING(WHITE) .............................................................................. 16
SYSTEM ........................................................................................ 21, 22
U
Upgrade .............................................................................................. 12
User file ..................................................................................................8
Load ...............................................................................................8
Save ...............................................................................................8
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
25
Download from Www.Somanuals.com. All Manuals Search And Download.
プロフェッショナルAVビジネスユニット
〒 571-8503 大阪府門真市松葉町 2 番 15 号
(06) 6901－1161
☎
©Panasonic Corporation 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
|