Ò
PAL
Digital Video Camera Recorder
Model AG-
E
Before operating this product, please read the instructions carefully and save this
manual for future use.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
Operating precaution
“Unauthorized recording of copyrighted
television programmes, video tapes and other
materials may infringe the right of copyright
owners and be contrary to copyright laws.”
Operation near any appliance which generates
strong magnetic fields may give rise to noise in the
video and audio signals. If this should be the case,
deal with the situation by, for instance, moving the
source of the magnetic fields away from the unit
before operation.
$ DO NOT REMOVE PANEL COVER
CAUTION:
BY UNSCREWING.
To reduce the risk of electric shock, do not
remove cover. No user serviceable parts inside.
Refer servicing to qualified service personnel.
Danger of explosion or fire if battery is
mistreated.
O Replace only with same or specified type.
O Do not disassemble or dispose of in fire.
O Do not store in temperatures over 60°C.
O Use specified charger for rechargeable
batteries.
O Do not recharge the battery if it is not a
rechargeable type.
For Remote Controller
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD AND ANNOYING INTERFERENCE,
USE THE RECOMMENDED ACCESSORIES
ONLY.
O Replace battery with part No. CR2025 only.
O Do not recharge the battery.
CAUTION:
WARNING:
Do not install or place this unit in
a
TO REDUCE THE RISK OF FIRE OR SHOCK
bookcase, built-in cabinet or any other
confined space in order to maintain
adequate ventilation. Ensure that curtains
and any other materials do not obstruct the
ventilation to prevent risk of electric shock
or fire hazard due to overheating.
HAZARD,
DO
NOT
EXPOSE
THIS
EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, KEEP THIS EQUIPMENT AWAY
FROM ALL LIQUIDS-USE AND STORE ONLY
IN LOCATIONS WHICH ARE NOT EXPOSED
TO THE RISK OF DRIPPING OR SPLASHING
LIQUIDS, AND DO NOT PLACE ANY LIQUID
CONTAINERS ON TOP OF THE EQUIPMENT.
AC Adapter
OThe rating plate is on the underside of the AC
Adapter.
ODisconnect the AC mains plug from the AC
mains socket when not in use.
CAUTION:
The socket-outlet shall be installed near the
equipment and shall be easily accessible.
indicates safety information.
To remove the battery/
Attention/Attentie
O Batteries are used for the main power source,
memory back-up in the product and remote
controller.
At the end of their useful life, you should not throw
them away.
Verwijderen van de batterij
Main Power Battery
Batterij Voor Primaire Voeding
Instead, hand them in as small chemical waste.
O Voor de primaire voeding en het reservegeheugen
van
het
apparaat,
alsmede
voor
de
Battery eject button
Batterij verwijderknop
afstandsbediening, wordt gebruik gemaakt van een
batterij.
Wanneer de batterij uitgeput is, mag u deze niet
gewoon weggooien, maar dient u ze als klein
chemisch afval weg te doen.
1
2
3
3 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . .5
Precautions for use . . . . . . . . . . . . . . . . . . . .6
Storage tips . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Parts and their functions . . . . . . . . . . . . . . . .9
Remote control unit . . . . . . . . . . . . . . . . . . .19
Charging the battery . . . . . . . . . . . . . . . . . .20
Mounting the battery . . . . . . . . . . . . . . . . . .21
Supplying power from the AC adapter . . . .21
Cassette tapes . . . . . . . . . . . . . . . . . . . . . . .22
Adjusting the hand strap . . . . . . . . . . . . . . .23
Attaching the shoulder strap . . . . . . . . . . . .23
Mounting the lens hood . . . . . . . . . . . . . . . .23
Viewfinders . . . . . . . . . . . . . . . . . . . . . . . . . .24
Setting the calendar . . . . . . . . . . . . . . . . . . .27
Charging the internal battery . . . . . . . . . . .28
Setting the electronic shutter . . . . . . . . . . .29
Screen displays . . . . . . . . . . . . . . . . . . . . . .50
Camera mode and VCR mode . . . . . . . . . .50
VCR mode . . . . . . . . . . . . . . . . . . . . . . . . .55
Selecting the display . . . . . . . . . . . . . . . . . .56
Connecting external components . . . . . . . .57
Inputting to and outputting from analog
components . . . . . . . . . . . . . . . . . . . . . . . .57
Inputting to and outputting from digital
components . . . . . . . . . . . . . . . . . . . . . . . .58
Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Preparation and inspections . . . . . . . . . . . .59
Regular shooting . . . . . . . . . . . . . . . . . . . .59
REC check . . . . . . . . . . . . . . . . . . . . . . . . .59
Face-to-face shooting . . . . . . . . . . . . . . . . .60
Index recording . . . . . . . . . . . . . . . . . . . . . .60
Using the USER buttons . . . . . . . . . . . . . . .60
Intermittent recording . . . . . . . . . . . . . . . . .60
Backup recording . . . . . . . . . . . . . . . . . . . .61
Progressive shooting . . . . . . . . . . . . . . . . .62
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Normal playback . . . . . . . . . . . . . . . . . . . . .63
Tape blank search . . . . . . . . . . . . . . . . . . .63
Variable speed search . . . . . . . . . . . . . . . .63
Index search . . . . . . . . . . . . . . . . . . . . . . . .63
Condensation . . . . . . . . . . . . . . . . . . . . . . . .64
Video heads . . . . . . . . . . . . . . . . . . . . . . . . .64
Troubleshooting (Q&A) . . . . . . . . . . . . . . . .65
Power supply-related problems . . . . . . . . .65
Battery-related problems . . . . . . . . . . . . . .65
Problems during normal video recording . .65
Problems during various kinds of video
White balance and black balance . . . . . . . .31
Adjusting the white balance . . . . . . . . . . . .31
Adjusting the black balance . . . . . . . . . . . .32
ATW (Auto Tracking White) function . . . . .32
Setting the time data . . . . . . . . . . . . . . . . . .33
Setting the user’s bit . . . . . . . . . . . . . . . . . .33
Setting the time code . . . . . . . . . . . . . . . . .34
Scene files . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Changing the scene file settings . . . . . . . . .36
Setting menus . . . . . . . . . . . . . . . . . . . . . . . .38
Operation method . . . . . . . . . . . . . . . . . . . .38
Configuration of setting menus . . . . . . . . . .39
SCENE FILE screen . . . . . . . . . . . . . . . . . .40
CAMERA SETUP screen . . . . . . . . . . . . . .41
SW MODE screen . . . . . . . . . . . . . . . . . . .42
AUTO SW screen . . . . . . . . . . . . . . . . . . . .43
PLAYBACK FUNCTIONS screen . . . . . . . .43
RECORDING SETUP screen . . . . . . . . . . .44
AV IN/OUT SETUP screen . . . . . . . . . . . . .46
DISPLAY SETUP screen . . . . . . . . . . . . . .47
OTHER FUNCTIONS screen . . . . . . . . . . .48
recording . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Editing-related problems . . . . . . . . . . . . . . .66
Display-related problems . . . . . . . . . . . . . .66
Playback-related problems (video) . . . . . . .66
Playback-related problems (audio) . . . . . . .67
Other types of problems . . . . . . . . . . . . . . .67
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . .68
Specifications . . . . . . . . . . . . . . . . . . . . . . . .69
O “LEICA” is the registered trademark of Leica Microsystems.
O “DICOMAR” is the registered trademark of Leica Camera AG.
Other model names, company names, products names, etc. are the trademarks and registered
trademarks of the companies concerned.
4 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
OBattery (2)
OEye cup (VMG1458)
OMicrophone holder (VYC0870)
OScrews
OAC adapter (2)
6 mm in length (XSB4+6FZ) a2
12 mm in length (XSB4+12FZ) a2
OMicrophone holder adapter (VYC0890)
OAC cable
(U.K. only: K2CT3DA00001)
OShoulder strap (VFC3891)
OMini DV cassette tape (AY-DVM63MQ)
OFerrite Cores
(All areas except U.K.: K2CR2DA00005)
ODC cable (VEK8722)
Ferrite Cores for DV Interface Cable:
(J0KG00000013)
OWireless remote control unit (VFA0402)
When the DV Interface cable is to be
connected, attach one Ferrite Core to one
end of the cable and the other one to the
other end.
OBattery for remote control unit (CR2025)
2 :
Refer to the “OPTIONAL ACCESSORIES”
item (on page 70) for the model numbers of
the battery and AC adapter.
5 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions for use
Take care to prevent water from entering
inside the camera recorder when using it in
the rain or snow or at the seashore or in
other similar environments.
OFailure to heed this caution may cause the
camera recorder and/or cassette to
malfunction (possibly leading to irreparable
damage).
AC adapter and battery
OWhen the temperature of the battery unit has
risen to an extremely high level or dropped to
an extremely low level or when the battery is
not used for prolonged periods of time and has
become fully discharged, the “CHARGE” lamp
flashes several times, and charging
commences automatically.
OIf the “CHARGE” lamp continues to flash even
though the battery temperature is normal,
consult your dealer as a problem may have
developed within the battery or AC adapter.
OWhen the battery is warm, it takes longer than
usual for the battery to be charged.
OWhen the AC adapter is used near a radio, the
radio sound may be distorted. Use the
adapter at a distance of at least one meter
from the radio.
Keep the camera recorder away from
equipment (such as TV sets and TV game
machines) that generate magnetic fields.
OWhen the camera recorder is used on top of or
in the vicinity of a TV set, the radiation of
electromagnetic waves from the set may give
rise to interference in the picture and/or sound.
OThe strong magnetic fields generated by
speakers or large motors may ruin the tape
recordings or distort the images.
ONoise may be heard while the AC adapter is in
use; however, this is normal and not indicative
of any malfunctioning.
OThe
electromagnetic
waves
from
microcomputers may have an adverse effect
on the camera recorder or give rise to
distortion in the images and sound.
When carrying the camera recorder, take
care not to drop it.
OA strong impact may damage the camera
recorder body and render it incapable of
proper operation.
OWhen carrying the camera recorder, always
use the hand strap or shoulder strap and
handle the camera carefully.
OIf the camera recorder is adversely affected by
a component that generates magnetic fields to
such an extent that it can no longer operate
normally, turn off the power and remove the
battery or disconnect the AC adapter from the
power outlet, then re-install the battery or
reconnect the AC adapter to the outlet. After
this, switch the camera recorder’s power back
on.
Keep the camera recorder away from
insecticide sprays and volatile liquids.
OIf the camera recorder comes into contact with
insecticide sprays or volatile liquids, the
camera body may become deformed or the
surface coating may peel off.
OEnsure that the camera recorder does not
remain in close contact with rubber or plastic
products for prolonged periods of time.
Do not use the camera recorder near radio
transmitters or high-voltage equipment.
OIf the camera recorder is used near a radio
transmitter or high-voltage equipment, the
recorded pictures and/or sound may be
adversely affected.
When using the camera recorder on the
seashore or other similar environment, take
care to ensure that no sand or dust enter
inside the camera recorder.
OSand and dust may damage the camera
recorder and/or cassette. (Take particular
care when inserting and ejecting the cassette.)
After use, be absolutely sure to remove the
cassette and either remove the camera
recorder’s battery or disconnect its AC cable
from the power outlet.
OIf a cassette is left inside the camera recorder,
tape slack may develop and result in damage
to the tape.
OIf the battery is left inside the camera recorder
for a prolonged period, its voltage may drop to
such a low level that even after it has been
recharged, it may not be possible to re-use it.
6 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions for use
Battery characteristics
LCD
This camera recorder uses a rechargeable
lithium-ion battery which produces electrical
energy by means of an internal chemical
reaction. This reaction tends to be easily
affected by the ambient temperature and
humidity, and the period during which the
battery can be effectively used decreases as the
temperature becomes very high or low. The
battery charge will last for only 5 minutes if the
battery is used in an environment where the
temperature is extremely low.
OIf the same image or characters are left
displayed for a prolonged period on the LCD
monitor or viewfinder, the image may be
burned onto the screen. If this happens,
keep the power off for several hours to
restore the screen to its original condition.
OThe liquid crystal parts are fabricated using
high-precision technology. The screen has
effective pixels that cover more than 99.99%
of its area, but pixels may be missing or
remain permanently lit in less than 0.01% of
the area. This is neither indicative of
malfunctioning nor does it affect the images
in any way.
OIn locations where the temperature fluctuates
considerably, condensation may form on the
liquid crystal parts of LCD monitor. If this
happens, wipe off the moisture using a soft,
dry cloth.
OIf the temperature of the camera recorder
itself is very low, the LCD monitor may be
slightly darker than usual immediately after
the power has been turned on. Normal
brightness is restored after the internal
temperature has risen.
When the battery temperature rises to an
abnormally high level, the protection function is
activated, and it is not possible to use the
battery for a while.
Always remove the battery upon completion
of operation.
Never fail to remove the battery from the
camera recorder. (If it is left in the camera, a
small amount of current will be consumed even
when the camera recorder’s power is off.) If the
battery is left in the camera for a prolonged
period, it will become excessively discharged to
the extent that even after it has been recharged,
it may not be possible to re-use it.
Do not point the lens or viewfinder’s eye-
piece at the sun.
Disposing of the battery
ODispose of the battery when it has reached
the end of its service life.
Doing so may damage the internal parts.
ODo not dispose of the battery in a fire as it
may explode.
Protective caps for the connectors
Keep the protective caps in place over any
connectors which are not being used.
Protect the battery terminals.
Ensure that the battery terminals are free from
dust and foreign matter.
If the battery has been dropped, check that the
battery body and terminals have not been bent
out of shape.
Inserting a deformed battery into the camera
recorder or mounting it in the AC adapter may
result in damage to the camera recorder or AC
adapter.
7 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage tips
When storing the camera recorder, eject the
cassette from the camera recorder and remove
the battery.
Store all components in a location where the
humidity level is low and the temperature is
relatively stable.
Recommended temperature range:
15°C to 25°C
Recommended relative humidity:
40% to 60%
Cassette tapes
OBefore storing a cassette tape, rewind the
tape to its start. If a tape that has been
stopped at some interim point along its length
is stored for six months or more (this period
of time differs depending on the storage
conditions), tape slack will develop. Always
rewind the tape to its start before storing it.
OReturn cassette tapes to their original cases
before storing them. Dust, direct sunlight
(ultraviolet rays), humidity and other such
conditions may damage the tapes. Dust
contains particles of hard mineral substances,
and if dust should enter inside a cassette,
these particles may in turn be transferred to
the heads and other parts, possibly resulting
in their damage. Make a habit of always
returning the cassettes to their original cases.
OFast forward and rewind cassette tapes once
every six months. If tapes are kept wound up
for more than a year, they may become
warped or distorted due to the expansion and
contraction caused by changes in the
temperature and humidity. In addition, layers
of tape may stick together.
Camera recorder
OWrap the camera recorder in soft cloth to
keep out dust.
Battery
OThe battery’s service life is reduced if the
battery is stored in a location where the
temperature is extremely high or extremely
low.
OIf the battery is stored in a location exposed
to high concentrations of oily vapors and/or
dust, the terminals may corrode or other
problems may develop, possibly resulting in
malfunctioning.
ODo not bring metal objects (such as
necklaces or hairpins) into contact with
the battery terminals. The terminals may
short circuit and generate heat, and
touching them in this condition may cause
severe burns.
OStore the battery only when it is fully
discharged. It is recommended that the
battery be charged once a year when it is
being stored long-term and that it be placed
back in storage after it has been fully
discharged using the camera recorder.
ODo not place cassette tapes near matter or
equipment which emits strong magnetic
fields.
OExtremely fine magnetic particles are
contained in the coating of the tape surface,
and it is here that the signals are recorded.
Magnetic necklaces, toys and other such
items may have stronger magnetic fields than
suspected, which may erase recordings or
give rise to noise in the pictures and sound.
8 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
7 3
2
8
(Eye cup)
9
:
(Eye-piece)
=
<
;
56 1
4
1POWER switch
4Cassette holder
Move this switch while pressing the lock
release button.
5CAM REMOTE jack (2.5 mm mini jack)
The remote control unit is connected to this
jack to enable zooming and record start/stop
to be initiated by remote control.
PO
WER
O
N
OFF
6PHONES jack (3.5 mm stereo mini jack)
The headphones are connected to this jack to
monitor the sound.
Lock release button
2START/STOP button
7Remote control sensor (rear)
When this button is pressed in the camera
mode, shooting can be started or stopped.
Operation is switched between the camera
mode and VCR mode using the
CAMERA/VCR button >.
8Tally lamp (rear)
This lights or blinks depending on the status
of the camera recorder.
Lights: While shooting is in progress.
3EJECT switch
Blinks:
To open the cassette holder, slide this switch
in the direction of the arrow while pressing
the lock release button.
Do not operate the switch while recording is
in progress. The cassette holder will open
but recording will continue, so external light
and/or dust will adversely affect the tape.
O When a remote control operation has been received
(about 8 blinks per second)
O When shooting is commenced
(about 8 blinks per second)
O When the tape has come to the end
(about 4 blinks per second)
O When a problem has arisen in the tape transport
system (about 4 blinks per seconds)
O When there is little tape or battery charge remaining
(once a second)
O
Do not insert or eject the cassette tape
holding onto the cassette holder alone.
Insert or eject the tape with the camera
recorder placed on a flat and stable
surface or, alternatively, support the
camera recorder with both hands so that it
will be kept in a stable condition even if
the cassette holder is opened.
The settings for causing the tally lamp to flash
are performed using the REC LAMP item on
the setting menu OTHER FUNCTIONS
screen. (See page 48)
9Viewfinder
O
Close the cassette holder after
ensuring that the cassette mechanism
has completed the eject operation.
:Diopter adjustment dial
This is adjusted in such a way that the
viewfinder screen comes into sharp focus.
;Power socket
EJECT
<DC INPUT connector (7.9V)
Lock release button
=Battery eject button
9 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
White balance sensor
B
A
@ ? >
>CAMERA/VCR button and lamp
Each time this button is pressed, the
operation mode is switched between the
camera mode and VCR mode, and the lamp
of the selected mode lights.
OThis function may not operate properly if
there is an unrecorded blank near the tape
start or at a point along the tape.
OBefore proceeding with recording, check
the picture which has been searched.
Select the camera mode for shooting.
Select the VCR mode to check the tape
contents or input and record video signals
from an external source.
AGAIN switch
When the camera screen is too dark, change
the setting of this switch to boost the gain and
make the screen brighter. The M and H gain
values are set using the MID GAIN item and
HIGH GAIN item on the setting menu SW
MODE screen. (See page 42)
L : The switch is normally kept at this
position. (0 dB)
M : The gain of the camera video amplifier is
boosted. (Factory setting: 6 dB)
?Scene file dial
This is used to select the scene files. (See
page 35) Settings tailored to various shooting
conditions are stored in the positions of this
dial. During shooting, the necessary file can
be instantly loaded using the dial.
@EVF DTL/END SEARCH button
When this button is pressed inthe camera
mode, the outlines of the images in the
viewfinder and on the LCD monitor are
accentuated, and focusing is thereby facilitated.
“EVF DTL ON” will also be displayed on the
center of the screen for approximately 2
seconds. However, the images which are
recorded at this time will be the regular images
whose outlines are not accentuated.
H : The gain of the camera video amplifier is
further boosted. (Factory setting: 12 dB)
BWHITE BAL switch
This is used to set the white balance.
A or B:
The white balance value adjusted by the
AWB button C is stored in the memory.
PRST (preset):
Pressing the button once again will return the
unit to its original status. “EVF DTL OFF” will
also be displayed on the center of the screen
for approximately 2 seconds.
When this button is pressed in the VCR
mode, the unrecorded blanks on the video
tape are searched, and the still picture mode
is established about one second before an
unrecorded blank.
The part which was shot last can also be
searched using the END SEARCH item
setting on the setting menu PLAYBACK
FUNCTIONS screen. (See page 43)
OWhen one tape is replaced with another,
the part which was shot last cannot be
searched using this button.
Set the switch to this position in cases
where, for instance, there is no time to
adjust the white balance.
The 3200K and 5600K white balance
values are stored in the memory.
Press the AWB button to switch between
the two values.
OThe ATW (Auto Tracking White) function
can be allocated to the A, B or PRST
position using the ATW item on the setting
menu SW MODE screen. (See page 42)
OWhat kind of light source is being used
during shooting is determined by the white
balance sensor.
Do not block the front of the white balance
sensor with your hand or any other object
during shooting or the ATW function will
not operate properly.
OIf no signals have been recorded on the
tape, the tape stops at the tape end.
10 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
Zoom ring pin
EIRIS dial
This is used to adjust the lens iris.
When the IRIS button D is set to the manual
mode, this dial is used to adjust the lens iris.
Even in the auto mode, the lens iris can be
adjusted using this dial.
OThe direction in which the IRIS dial is
turned and iris control can be set using the
IRIS DIAL item on the setting menu SW
MODE screen. (See page 42)
H
I
F
G
D
E
C
FFOCUS switch
This is used to select the method of
controlling the focus.
A (AUTO):
Auto focus mode
M (MANUAL):
Manual focus mode
The focus ring H is controlled manually to
adjust the focus.
CAWB button
When this button is pressed while the WHITE
BAL switch B is set to the A or B position,
the white balance is automatically adjusted,
and the white balance value is stored in the
memory.
:
∞
If this button is then held down, the black
balance is adjusted.
After the focal length has been set to
infinity, the manual focus mode is
established. Even if the FOCUS switch is
When this button is pressed while the WHITE
BAL switch B is set to the PRST position, the
current white balance value is displayed.
When the AWB button is pressed again, the
3200K and 5600K white balance values are
selected alternately.
set to the
(MANUAL) position.
position, it will return to the M
∞
OEven when the manual focus mode is
established, the AUTO button J setting
takes priority if it is pressed.
OIf flicker occurs, the auto focus control may
not be exercised properly, so select a
shutter speed suited to the lighting. (See
page 29)
OWhile recording is in progress, the black
balance cannot be adjusted.
DIRIS button
OThe focus assist mode is established if the
auto focus mode is selected in the
progressive mode or slow shutter mode.
Focusing can be conducted more precisely
than in the manual focus mode, but it takes
slightly longer to exercise focus control
compared with the regular auto focus
mode.
Each time this button is pressed, the method
of adjusting the lens iris is switched between
the auto mode and manual mode.
<Note>
The maximum aperture of the lens iris of this
unit is F1.6 when the lens is at the full zoom
(W) position and F2.8 at the full TELE (T)
position.
The display shown for the F-number in the
viewfinder and/or LCD monitor is “OPEN”
when the lens is at the full zoom (W) position
and “F2.8” or “OPEN” when the lens is at the
full TELE (T) position.
GPUSH AUTO button
While this button is pressed with the FOCUS
switch set to the M (MANUAL) position, the
auto focus mode is established, and the focus
is adjusted.
HFocus ring
IZoom ring
If the zoom ring pin is not required, fit it into
the threaded hole under the handle so that it
will not be lost.
11 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
MAUDIO controls
N
J
O
These are used to adjust the recording level
of the audio signals which have been input to
the built-in microphone P and INPUT 1 and 2
connectors Y.
S
K
P
Adjust the recording level of the audio signals
using these controls, irrespective of the
setting selected for the MIC ALC item on the
RECORDING SETUP screen of the setting
menu (page 44).
It is recommended that the centre position
normally be selected for use.
OThey cannot be used to adjust the audio
signals which have been input to the
AUDIO IN/OUT CH1 and CH2 connectors
V.
Q
R
M
L
JAUTO button
When the AUTO button is pressed, the
operation mode which was set on the setting
menu AUTO SW screen is established, and
“ A ” appears in the upper part of the
viewfinder and LCD monitor.
NLight shoe
A video light, for instance, is attached to this
shoe.
On the setting menu AUTO SW screen, the
mode of the operation to be performed
automatically (auto iris, auto gain control,
auto tracking white or auto focus) when the
AUTO button is pressed is set.
OMicrophone shoe
The accessory microphone holder is attached
to this shoe so that a microphone (optional
accessory), etc. can be mounted. (See page
57)
(See page 43)
The setting is released when the button is
pressed again.
PMicrophone (built-in, stereo)
Do not apply a strong load from an external
source to this microphone as it may damage
the microphone.
KUSER1, USER2 and USER3 buttons
One of 11 functions can be allocated in turn
to each of the USER1, USER2 and USER3
buttons.
In accordance with the subject concerned,
the shooting conditions can be instantly
selected or fade effects can be added to the
images.
QTally lamp (front)
Refer to the details on the tally lamp (rear) 8.
RRemote control sensor (front)
SMENU button
For details, refer to the USER1 item, USER2
item and USER3 item (page 42) on the
setting menu SW MODE screen.
When this button is pressed, the menu mode
is established, and the setting menu screen is
displayed in the viewfinder and on the LCD
monitor.
When it is pressed again, the menu mode is
released.
LND FILTER switch
This is used to select the ND filter (for
adjusting the light quantity) to be used.
OFF: The ND filter is not used.
1/8 : The light quantity is reduced to about
one eighth.
1/64: The light quantity is reduced to about
one sixty-fourth.
12 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
[In the camera mode]
“5” :
T
When the lever is tilted in the “5”
direction in the shooting pause mode, the
tape is played back in the “5” direction
at 1a speed while the lever is tilted.
“6” :
When the lever is tilted in the “6”
direction in the shooting pause mode, the
tape is played back in the “6” direction
at 1a speed while the lever is tilted.
OThe scenes shot up until now can be
checked in the shooting pause mode.
U
V
Y
W Z
X
TOPERATION lever
US-VIDEO IN/OUT connector
This is the S-video input/output connector.
This lever is used to operate the VCR and
conduct the menu operations.
[In the VCR mode]
VAUDIO IN/OUT CH1 and CH2 connectors
(pin jacks)
“1” :
When the lever is tilted in the “1” direction
in the stop mode, the tape is played back.
When it is tilted in the same direction
during playback, the variable speed search
mode (see page 63) is established, and the
tape is played back at the 1a speed.
(Sound is not played back.)
“5” :
These are the input/output connectors for the
audio signals.
WVIDEO IN/OUT connector
(pin jack)
This is the input/output connector for the
video signals.
When the lever is tilted in the “5”
direction in the stop mode, the tape is fast
forwarded.
XDV connector
An IEEE1394 (4-pin) cable (optional
accessory) is connected here.
When it is tilted in the same direction
during playback, the tape is cued at 10a
speed.
Video signals, audio signals or time codes,
for instance, can be input and output digitally.
“6” :
YINPUT 1, 2 connectors (XLR, 3-pin)
External microphones or audio components
are connected here.
When the lever is tilted in the “6”
direction in the stop mode, the tape is
rewound.
When it is tilted in the same direction
during playback, the tape is reviewed at
10a speed.
ZINPUT 1/2 switch
This is used to switch the audio input signals
which are connected to the INPUT 1 and 2
connectors.
“$” :
When the lever is tilted in the “$” direction,
the tape is stopped.
“;” :
When the lever is pressed during playback,
the tape is set to the pause (temporary
stop) mode.
LINE:
The audio input signals from the audio
component serving as the line input are
selected; their input level is 0 dBu.
MIC:
The audio input signals from the external
microphone(s) are selected; their input
level is –50 dBu.
[In the menu mode]
“3” :
When the lever is tilted in the “3” direction,
the items displayed on the menu screen
are moved upward.
The input level can be changed to –60 dBu
using the MIC GAIN 1 and MIC GAIN 2
items on the setting menu RECORDING
SETUP screen. (See page 44)
“4” :
When the lever is tilted in the “4” direction,
the items displayed on the menu screen
are moved downward.
“;” :
Press the lever to change a setting.
13 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
a
_\
`
b
c
^
]
[
ZOOM
SERVO
MANU
[ZOOM switch
aAUDIO DUB button
This is used to select motor-driven zoom
operations or manual zoom operations.
SERVO:
For motor-driven zoom operations
(At this position, do not attempt to perform
manual zoom operations or malfunctioning
may result.)
When the pause status is established in the
VCR mode and this button is pressed, the
mode in which audio dubbing can be started
is established.
Press “ ” of the OPERATION lever T to
;
record the sound. To stop the recording, tilt
the OPERATION lever in the “ ” direction.
$
MANU:
For manual zoom operations
The audio input used for audio dubbing is set
using the A DUB INPUT item on the setting
menu AV IN/OUT SETUP screen. (See page
46)
\START/STOP button (on the handle)
When this button is pressed in the camera
mode, shooting start or stop is selected.
The camera mode and VCR mode are
switched using the CAMERA/VCR button >.
OBefore proceeding with the audio dubbing,
select “32K (12 bit)” as the AUDIO REC
item setting on the setting menu
RECORDING SETUP screen and then
start shooting. (See page 44)
]REC CHECK button
bVCR REC buttons
When this button is pressed in the shooting
pause mode, the picture and sound
immediately before shooting was stopped are
played back for several seconds, and the
shooting pause mode is established at the
original position on the tape.
When these two buttons are pressed at the
same time in the stop status of the VCR
mode, the video signals from the connected
component are recorded.
When they are pressed at the same time in
the playback pause status of the VCR mode,
the recording standby status is established.
^Zoom button
Each time “ ” of the OPERATION lever T is
;
When the ZOOM switch is at the SERVO
position, motor-driven zoom operations are
performed.
When this button is pressed lightly, zoom
operations are performed at a low speed;
when it is pressed with force, they are
performed at a high speed.
pressed, the status alternates between
recording and recording standby.
To stop recording, tilt the OPERATION lever
in the “ ” direction.
$
OBefore proceeding to record, check that the
video signals have been input.
cAUDIO MON/VAR buttons
These buttons are used to adjust the volume
at which the sound is to be output from the
internal speaker f or PHONES jack 6.
The playback direction and playback speed
are changed in the variable speed search
mode. (See page 63)
When these buttons are pressed in the pause
status, the tape is played back frame by
frame.
_Zoom button (on the handle)
`HANDLE ZOOM switch
This switch is used to select one of the three
speeds for the zoom operations conducted
using the zoom button _ on the handle.
The speed is set using the HANDLE ZOOM
item on the setting menu SW MODE screen.
(See page 42)
14 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
f
g
h
i
k m
j l
e
d
dOPEN button
iSPEED SEL button
Press the OPEN button in the direction of the
arrow to open the LCD monitor e.
When the LCD monitor is opened, the image
on the viewfinder switches to the LCD
monitor.
After pressing the SHUTTER button h or
when the slow shutter mode is established,
press this button to select the shutter speed.
(See page 29)
The image can be switched using the EVF
MODE item on the setting menu DISPLAY
SETUP screen. (See page 48)
jCH1 SELECT switch
This switch is used to select the input signals
which are to be recorded on the audio
channel 1 track.
OPEN
INT (L):
Audio signals of the left (L) channel of the
internal microphone
INPUT1:
Audio signals which are input to the INPUT
1 connector
INPUT2:
eLCD monitor
Audio signals which are input to the INPUT
2 connector
fInternal speaker
gRESET button
kCH2 SELECT switch
If the camera recorder cannot be operated
even though its power is on or some other
form of trouble has occurred, use a pointed
object to press the RESET button. This will
reset the system microcomputer.
Even after resetting has been initiated, the
entered setting menu values and memory
contents will not be erased.
This switch is used to select the input signals
which are to be recorded on the audio
channel 2 track.
INT (R):
Audio signals of the right (R) channel of the
internal microphone
INPUT2:
Audio signals which are input to the INPUT
2 connector
Refrain from pressing the RESET button
when the camera recorder is operating
properly.
lINPUT 1 switch (MIC POWER +48 V)
When this switch is set to ON, +48 V power
(power supply for the phantom mic) is
supplied to the INPUT 1 connector.
hSHUTTER button
Press this button to change the shutter
speed.
After pressing this button, press the SPEED
SEL button i to select the shutter speed.
(See page 29)
This button cannot be operated in the slow
shutter mode.
mINPUT 2 switch (MIC POWER +48 V)
When this switch is set to ON, +48 V power
(power supply for the phantom mic) is
supplied to the INPUT 2 connector.
15 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
p
q
s
o
n
r
nCOUNTER RESET button
pMODE CHK button
This button is used to reset the counter value
on the counter display and the memory
counter value to zero.
When this button is pressed, the current
camera status setting can be checked in the
viewfinder and on the LCD monitor.
It cannot reset the time code or user’s bit.
qZEBRA button
oCOUNTER button
When this button is pressed in camera mode,
a zebra pattern or marker appears in the
viewfinder and on the LCD monitor, enabling
the brightness of the subject to be checked.
Each time it is pressed, the display changes
as shown below.
This button is used to select what data is to
be displayed on the counter display which is
in the viewfinder and on the LCD monitor.
Each time it is pressed, the data to be
displayed changes.
COUNTER:
The counter value is displayed.
OFF
M COUNTER:
The counter value in the memory stop
mode is displayed.
TC : The time code is displayed.
UB : The user’s bit is displayed.
FR : The frame rate information (25P) when
shooting is to be performed in the
progressive mode is displayed.
Blank display :
ZEBRA 2
ZEBRA 1
Marker
The level of each zebra pattern can be set
using the ZEBRA DETECT 1 item and
ZEBRA DETECT 2 item on the setting menu
DISPLAY SETUP screen.
The zebra pattern which has been set is
displayed as a percentage for the prescribed
time (approx. 2 seconds).
Display of the marker can also be switched
ON/OFF with the MARKER item on this
screen. (See page 47)
No data is displayed.
Memory stop mode
The memory stop mode is established when the
Zebra pattern
Parts that may be whitened out due to overexposure
are displayed using a striped pattern.
display is switched to
COUNTER button.
M
COUNTER using the
1 Switch the display to M COUNTER, and press the
COUNTER RESET button n at any tape position to
reset the counter value.
2 Proceed with playback or shooting.
3 Establish the VCR mode using the CAMERA/VCR
button.
4 When the tape is now rewound or fast forwarded, it
stops travelling automatically near where the counter
value was reset.
O If the counter value is reset at the OUT point during
audio dubbing, audio dubbing can be stopped in the
memory stop mode.
rOIS button
This button is used to set camera shake
compensation to ON or OFF. When the
compensation is ON,
viewfinder and on the LCD monitor.
Select ON or OFF to suit the shooting
conditions.
appears in the
When shooting using a tripod, the OFF
setting is recommended.
sTripod mounting hole
16 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
Remote control unit
START/
STOP
DATE/ PHOTO
TIME SHOT
OSD
1
2
3
8
4
COUNTER RESET TITLE
MULTI/
ZOOM
5
7
6
P-IN-P
REC
A.DUB
C
B
/REW PLAY
FF/
STILL ADV PAUSE STILL ADV
INDEX STOP INDEX
SELECT
VAR.
PB.
ZOOM
SEARCH
STORE
MENU
SET
OFF/ON
P.B.DIGITAL
ITEM
5COUNTER button
The buttons listed below are for functions
which are not featured on the camera
recorder.
This button has the same function as the
COUNTER button on the camera recorder
body.
OPHOTO SHOT
OMULTI/P-IN-P
OSTORE
OTITLE
OSELECT
OOFF/ON
O N
6COUNTER RESET button
This button has the same function as the
COUNTER RESET button on the camera
recorder body.
OPB. ZOOM
1OSD button
When this button is pressed, the information
displayed in the viewfinder and on the LCD
monitor is added to the video signals, and it
can be displayed on a TV monitor as well.
When it is pressed again, the display on the
TV monitor is cleared.
7REC button
When this button is pressed together with the
PLAY button while operation is stopped in the
VCR mode, the video signals from the
connected component are recorded.
When it is pressed together with the PLAY
button during playback pause in the VCR
mode, the recording standby status is
established.
Each time the PAUSE (;) button is pressed,
the status is switched between recording and
recording standby.
To stop recording, press the STOP ($)
button.
2DATE/TIME button
When this button is pressed, the shooting
date (year/month/day) and/or time are
displayed in the viewfinder and on the LCD
monitor.
Each time it is pressed, the display is
switched in the sequence shown below.
No display
8A. DUB button
Time display
This button has the same function as the
AUDIO DUB button on the camera recorder
body.
Date display
Time and date display
3START/STOP button
This button has the same function as the
START/STOP button on the camera recorder
body.
4ZOOM/VOL buttons
During shooting, these buttons are used to
conduct motor-driven zoom operations.
The zoom speed is fixed at the medium
speed.
During tape playback, they are used to adjust
the volume at which the sound is to be output
from the internal speaker and PHONES jack.
17 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
START/
STOP
DATE/ PHOTO
TIME SHOT
OSD
COUNTER RESET TITLE
MULTI/
ZOOM
P-IN-P
REC
A.DUB
C
B
/REW PLAY
FF/
STILL ADV PAUSE STILL ADV
INDEX STOP INDEX
9
:
;
SELECT
VAR.
PB.
SEARCH
ZOOM
STORE
MENU
SET
OFF/ON
P.B.DIGITAL
ITEM
9VCR operation buttons
:VAR. SEARCH button
C/REW button (6)
When this button is pressed during playback,
the variable search mode is established, and
“1a” is displayed in the viewfinder and on the
LCD monitor. When the “V” or “B” button
among the SET buttons ; is pressed, the
playback speed is changed.
Each time the “V” or “B” button is pressed,
the playback speed is changed by one setting
in the following sequence: 1/5a (or 1/3a in
the LP mode), 1a, 2a, 5a, 10a and 20a.
Use the “V” button to change the speed in
the forward direction and the “B” button to
change it in the reverse direction.
This button has the same function as the
OPERATION lever on the camera recorder
body.
FF/B button (5)
This button has the same function as the
OPERATION lever on the camera recorder
body.
PLAY button (1)
When this button is pressed in the VCR
mode, the tape is played back.
When it pressed together with the REC
button, the video signals from the
connected component are recorded.
STILL ADV buttons (E, D)
;SET buttons
When either button is pressed during tape
playback, slow-motion playback results.
When it is pressed in the pause status,
frame advance playback results.
(E in the reverse direction, D in the
forward direction)
MENU button:
This button has the same function as the
MENU button on the camera recorder
body.
“V” button:
When this is pressed in the menu mode,
the items displayed on the menu screen
are moved upward.
When it is pressed in the search mode, the
speed is changed in the forward direction.
“B” button:
When this is pressed in the menu mode,
the items displayed on the menu screen
are moved downward.
When it is pressed in the search mode, the
speed is changed in the reverse direction.
“M” button:
INDEX buttons (:, 9)
When either button is pressed during tape
playback, the start of a recorded section is
searched.
(: in the reverse direction, 9 in the
forward direction)
PAUSE button (;)
This button has the same function as the
OPERATION lever on the camera recorder
body.
STOP button ($)
This button has the same function as the
OPERATION lever on the camera recorder
body.
Press this in the menu mode to change
settings.
18 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control unit
Installing the battery
Remote control unit settings
In order to prevent mistakes made in operations
performed using remote control when two
camera recorders are operated at the same
time, the operation buttons on the camera
recorder and accessory wireless remote control
unit can be set to work for “VCR1” applications
and for “VCR2” applications.
1 While pushing the knob in the direction of the
arrow, pull out the holder.
Setting method
OWireless remote control unit
2 Insert the battery with the “+” marking face
When the STOP ($) and STILL ADV (D)
buttons among the VCR operation buttons
are pressed at the same time, the operation
buttons on the remote control unit are set to
be used for VCR1.
up.
Similarly, when the STOP ($) and STILL ADV
(E) buttons among the VCR operation
buttons are pressed at the same time, the
operation buttons on the remote control unit
are set to be used for VCR2.
When the battery in the remote control unit
has been replaced, the operation buttons are
set to be used for VCR1.
3 Return the holder to its original position.
OCamera recorder body
Set VCR1 and VCR2 using the REMOTE
item on the setting menu OTHER
FUNCTIONS screen. (See page 48)
OWhen the battery (CR2025) has completely
run down, replace it with a new one. (The
battery life is about one year although it
depends on how often the remote control unit
is used.) If the remote control unit is
operated near the camera recorder’s remote
control sensor and the camera recorder fails
to operate, it means that the battery has run
down.
If the camera recorder body and remote control
unit settings are at variance, “REMOTE” in red
letters lights up and is displayed in the
viewfinder and on the LCD monitor.
OKeep batteries out of the reach of small
children.
START/
DATE/ PHOTO
TIME SHOT
STOP
OSD
COUNTER RESET TITLE
MULTI/
ZOOM
P-IN-P
REC
A.DUB
C
B
/REW PLAY
FF/
STILL ADV PAUSE STILL ADV
INDEX STOP INDEX
SELECT
VAR.
PB.
ZOOM
SEARCH
STORE
MENU
SET
OFF/ON
P.B.DIGITAL
VCR 2
VCR 1
ITEM
19 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Charging the battery
Fully charge the battery using the AC adapter
before use.
Charging and recording times of accessory
battery
It is recommended that a spare battery be kept
on hand just in case it is needed.
Charging time
Continuous recording time
Approx. 330 minutes
Approx. 330 (310) minutes
1 Place the battery flat along the
mark
O The table above gives the approximate durations. The
figure in parentheses is the duration when the LCD monitor
is used.
O The durations in the above table apply when the ambient
temperature is 20°C and the relative humidity is 60%.
Charging may take longer at other temperature and
humidity levels.
on the AC adapter, and slide it into
position.
OIf the DC cable is connected to the AC
adapter, disconnect it before proceeding.
The battery cannot be charged if this cable
is connected.
ODo not bring metal objects (such as
necklaces or hairpins) into contact with
the battery terminals. The terminals
may short circuit and generate heat, and
touching them in this condition may
cause severe burns.
OThe battery heats up during operation and
during charging, as does the camera
recorder body.
OIf recording and stop operations are
repeated more than is necessary, the
recording time will be less than the values
given in the above table.
Connect the AC cable to the power outlet.
2
OThe “POWER” lamp and “CHARGE” lamp
on the AC adapter light up, and charging
commences.
OStore the battery only when it is fully
discharged. It is recommended that the
battery be charged once a year when it is
being stored long-term and that it be placed
back in storage after it has been fully
discharged using the camera recorder.
OWhen the temperature of the battery unit
has risen to an extremely high level or
dropped to an extremely low level or when
the battery is not used for prolonged
periods of time has become fully
discharged, the “CHARGE” lamp flashes
several times, and charging commences
automatically.
OIf the “CHARGE” lamp fails to light when
the battery has been mounted, re-mount
the battery.
CHARGE
POWER
Upon completion of the charging, the
“CHARGE” lamp on the AC adapter goes
off.
3
OIf the “CHARGE” lamp continues to flash
even though the battery temperature is
normal, consult your dealer as a problem
may have developed within the battery or
AC adapter.
Slide the battery out of position and
remove it.
4
OWhen the battery is warm, it takes longer
than usual for the battery to be charged.
OWhen the AC adapter is used near a radio,
the radio sound may be distorted. Use the
adapter at a distance of at least one meter
from the radio.
ONoise may be heard while the AC adapter
is in use; however, this is normal and not
indicative of any malfunctioning.
OThe battery cannot be charged while
supplying power from the AC adapter to the
camera recorder.
20 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the battery
Raise the viewfinder.
Removing the battery
While pressing the battery eject button, slide
1
the battery upward to remove.
OSet the POWER switch to OFF, and check
that the CAMERA/VCR lamp has gone off
before removing the battery.
OSupport the battery with your hand to
ensure that it will not drop.
Battery eject button
Push the battery straight in, and slide it
downward until it clicks into position.
2
1
2
3
Return the viewfinder to its original
position.
3
Supplying power from the AC adapter
Raise the viewfinder.
1
1
Push the battery-type connector on the
DC cable straight in, and slide it
downward until it clicks into position.
2
Connect the DC cable to the AC adapter.
Connect the AC cable to the power outlet.
3
4
5
2
Return the viewfinder to its original
position.
4
3
Connect the AC adapter correctly as
shown in the figure.
OThe battery cannot be charged while
supplying power from the AC adapter to the
camera recorder.
21 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Cassette tapes
Inserting a cassette tape
OAlso, before removing the cassette tape,
check that the power supply is connected to
the camera recorder, then slide the EJECT
switch.
OIf the a cassette is not going to be inserted
immediately after one has been removed,
keep the cassette holder closed.
ODo not attempt this operation while
recording is in progress. The cassette
holder will open but recording will continue,
so external light and/or dust will adversely
affect the tape.
Do not insert or eject a cassette tape by
taking hold of the cassette holder alone.
Insert or eject the tape with the camera
recorder placed on a flat and stable surface
or, alternatively, support the camera recorder
with both hands so that it will be kept in a
stable condition even if the cassette holder is
opened.
Check that the power supply (battery or AC
adapter) is connected to the camera
recorder.
1
To prevent accidental erasure of recordings
Set the cassette tab to “SAVE” in order to
prevent what has been recorded on the tape
from being erased by mistake.
While pressing the lock release button, slide
the EJECT switch in the direction of the
arrow to open the cassette holder.
2
EJECT
REC
SAVE
Lock release button
$ Use of the following mini DV cassette tapes
is recommended for this camera recorder:
AY-DVM30 (30 minutes in the SP mode)
AY-DVM60 (60 minutes in the SP mode)
O Do not use 80-minute mini DV cassette
tapes.
Insert the cassette tape as shown in the
figure below.
3
$ Even when material is shot in the LP mode,
the picture quality will not deteriorate but
mosaic-type noise may occur or certain
restrictions may apply to some of the
functions.
In the following cases, mosaic-type noise
may occur and/or proper operation may not
be possible.
O When a tape which was shot by this
camera recorder in the LP mode is
played back in another digital video
component
O When a tape which was shot by another
digital video component in the LP mode
is played back in this camera recorder
O When a tape which was shot by this
camera recorder in the LP mode is
played back in a digital video component
which is not equipped with the LP mode
O When slow or frame advance playback is
performed
4 Push the part marked “
PUSH CLOSE
” to close
the cassette holder securely.
OOperations cannot be performed while the
cassette holder is open.
PUSH CLOSE
O When the camera search function is used
$ Audio dubbing is not possible in the LP
mode as the track width on the tape is
narrower than the head width.
22 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the hand strap
Adjust the hand strap to match the size of your
hand.
Open the cover, and adjust the strap length.
1
Return the cover to its original position.
OEnsure that the cover is closed securely
2
and tightly.
Attaching the shoulder strap
It is recommended that the shoulder strap be
attached to ensure that you do not drop the
camera recorder.
20 mm or
more
20 mm or
more
Mounting the lens hood
Removing the lens hood
OLoosen the fixing screw, and turn the lens
hood counterclockwise to remove.
Mark
Mounting the lens hood
Fixing screw
OPosition the lens hood so that its mark is
facing upward, and fit the hood onto the lens.
OTurn the lens hood clockwise, and secure it
using the fixing screw.
23 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewfinders
This camera recorder has two viewfinders: a
viewfinder that uses a small LCD, and a 3.5-
inch LCD monitor.
Use the one that better suits the application and
the shooting conditions concerned.
OThe brightness and colour tones may differ
between the images in the viewfinder and on
the LCD monitor and the images on a TV
monitor.
Select YES as the setting for the EVF SET
item on the setting menu DISPLAY SETUP
screen.
OFor details on the menu operations, refer
to page 38.
4
5
Select the EVF COLOUR LEVEL item, tilt
the OPERATION lever in the 3 or 4
direction, and adjust the colour level of the
screen. (If the remote control unit is used,
press the “M” button among the SET
buttons.)
Use the TV monitor when performing the final
check of the images.
Using the viewfinder
EVFSET
Set the POWER switch on the camera
recorder to ON, and check that an image
appears in the viewfinder.
1
EVFCOLOURLEVEL
?
?
?
?
[–]
––––[+]
EVFBRIGHTNESS
OKeep the LCD monitor closed.
?
?
?
?
[–]
––––[+]
EVFCONTRAST
?
?
?
?
[–]
––––[+]
Position the viewfinder where its screen
images can be seen most comfortably.
2
PUSHMENUTORETURN
OThe
viewfinder
can
be
raised
perpendicularly up to angle of about 90
degrees.
Select the EVF BRIGHTNESS item, and tilt
the OPERATION lever in the 3 or 4
direction to adjust the screen’s brightness.
(If the remote control unit is used, press the
“M” button among the SET buttons.)
6
7
Adjust the diopter adjustment dial in such a
way that the characters on the viewfinder
screen come into sharp focus.
3
EVFSET
Eye-piece
Diopter adjustment
dial
EVFCOLOURLEVEL
?
?
?
?
[–]
––––[+]
EVFBRIGHTNESS
?
?
?
?
[–]
––––[+]
EVFCONTRAST
?
?
?
?
[–]
––––[+]
PUSHMENUTORETURN
Select the EVF CONTRAST item, tilt the
OPERATION lever in the 3 or 4 direction,
and adjust the contrast of the screen. (If the
remote control unit is used, press the “M”
button among the SET buttons.)
EVFSET
EVFCOLOURLEVEL
Do not point the viewfinder’s eye-piece at
the sun.
This may damage the internal parts.
?
?
?
?
[–]
––––[+]
EVFBRIGHTNESS
?
?
?
?
[–]
––––[+]
EVFCONTRAST
?
?
?
?
[–]
––––[+]
PUSHMENUTORETURN
24 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewfinders
Using the LCD monitor
Press the MENU button three times to
release the menu mode.
8
Set the camera recorder’s POWER switch to
ON.
1
OThe setting for the EVF SET item can be
returned to the factory setting by pressing
the COUNTER RESET button when the
item concerned has been selected so that
it is possible to change the setting.
OWhen ON is selected as the setting for the
EVF MODE item on the setting menu
DISPLAY SETUP screen, images will
always appear in the viewfinder even when
the LCD monitor is opened.
Press the OPEN button in the direction of the
arrow 1 to open the LCD monitor.
2
OEither colour or monochrome can be
selected to display the images in the
viewfinder (EVF COLOUR item on the
setting menu DISPLAY SETUP screen).
The resolution is the same with either
setting.
1
2
OWhen the EVF DTL/END SEARCH button
is pressed, the outlines of the images in the
viewfinder are accentuated, and focusing is
thereby facilitated.
Position the LCD monitor where its screen
3
images can be seen most comfortably.
OThe LCD monitor can be rotated up to 180
degrees toward the lens and up to 90
degrees toward you.
Attaching the eye cup
Do not allow an unreasonable amount
of force to be applied to the LCD
monitor while it is open. Doing so may
cause the unit to malfunction.
To attach the eye cup, align the projections
on the eye cup holder and eye cup, and fit the
holder and eye cup together.
OTurning the eye cup after attaching it to its
holder may cause the holder to become
disengaged.
If the eye cup holder becomes disengaged,
refer to the procedure described in
“Viewfinder maintenance” (page 68) to
reattach it.
Eye cup holder
Eye cup
180°
90°
Select YES as the setting for the LCD SET
item on the setting menu DISPLAY SETUP
screen.
4
OFor details on the menu operations, refer
to page 38.
Projection
25 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewfinders
Select the LCD COLOUR LEVEL item, and
Press the MENU button three times to
release the menu mode.
5
8
tilt the OPERATION lever in the 3 or 4
direction to adjust the screen’s colour level.
(If the remote control unit is used, press the
“M” button among the SET buttons.)
OThe setting for the LCD SET item can be
returned to the factory setting by pressing
the COUNTER RESET button when the
item concerned has been selected so that
it is possible to change the setting.
OWhen closing the LCD monitor, ensure that
it is closed properly.
OWhen the LCD monitor has been turned
toward the lens (for face-to-face shooting),
both the viewfinder and LCD monitor light
up at the same time.
LCDSET
LCDCOLOURLEVEL
?
?
?
?
[–]
––––[+]
LCDBRIGHTNESS
?
?
?
?
[–]
––––[+]
LCDCONTRAST
?
?
?
?
[–]
––––[+]
PUSHMENUTORETURN
OWhen the EVF DTL/END SEARCH button
is pressed, the outlines of the images on
the LCD monitor are accentuated, and
focusing is thereby facilitated.
Select the LCD BRIGHTNESS item, and tilt
the OPERATION lever in the 3 or 4
direction to adjust the screen’s brightness.
(If the remote control unit is used, press the
“M” button among the SET buttons.)
6
LCDSET
LCDCOLOURLEVEL
?
?
?
?
[–]
––––[+]
LCDBRIGHTNESS
?
?
?
?
[–]
––––[+]
LCDCONTRAST
?
?
?
?
[–]
––––[+]
PUSHMENUTORETURN
Select the LCD CONTRAST item, tilt the
OPERATION lever in 3 or 4 directions, and
adjust the contrast of the screen. (If the
remote control unit is used, press the “M”
button among the SET buttons.)
7
LCDSET
LCDCOLOURLEVEL
?
?
?
?
[–]
––––[+]
LCDBRIGHTNESS
?
?
?
?
[–]
––––[+]
LCDCONTRAST
?
?
?
?
[–]
––––[+]
PUSHMENUTORETURN
26 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the calendar
Presented below is a sample setting where the
calendar is set to December 25, 2003 and the
time is set to 5:20 PM.
Tilt the OPERATION lever in the 3 or 4
direction and set MONTH to DEC.
(If the remote control unit is used, press the
5
“M” button among the SET buttons.)
Set the camera recorder’s POWER switch to
ON.
1
CLOCKSET
YEAR2003
DEC
MONTH
Select YES as the setting for the CLOCK
SET item on the setting menu OTHER
FUNCTIONS screen.
2
DAY 24
HOUR 13
MIN. 7
OFor details on the menu operations, refer
to page 38.
PUSHMENUTORETURN
CLOCKSET
2000
YEAR
In the same way, press “;” of the
OPERATION lever, and move the setting
item to DAY, HOUR and MIN.
(If the remote control unit is used, press the
“B” button among the SET buttons.)
MONTHAPR
DAY 24
HOUR 13
MIN. 7
6
7
PUSHMENUTORETURN
Similarly, tilt the OPERATION lever in the 3
or 4 direction and set 25 for DAY, 17 for
HOUR and 20 for MIN.
Tilt the OPERATION lever in the 3 or 4
direction and set YEAR to 2003.
3
(If the remote control unit is used, press the
(If the remote control unit is used, press the
“M” button among the SET buttons.)
“M” button among the SET buttons.)
CLOCKSET
CLOCKSET
YEAR2003
MONTHDEC
DAY 25
HOUR 17
2003
YEAR
MONTHAPR
DAY 24
HOUR 13
MIN. 7
20
MIN.
PUSHMENUTORETURN
PUSHMENUTORETURN
The 24-hour system is used to display the
hours.
The year can be set from 2000 to 2089.
Press the MENU button three times to
release the menu mode.
Press “ ” of the OPERATION lever, and
move the setting item to MONTH.
4
8
;
(If the remote control unit is used, press the
“B” button among the SET buttons.)
An error will develop in the time, so check
whether the correct time is displayed before
shooting.
CLOCKSET
YEAR2003
APR
MONTH
DAY 24
HOUR 13
MIN. 7
PUSHMENUTORETURN
27 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Charging the internal battery
The date and time are stored in the memory
using the internal battery. When the “
”
display appears in the viewfinder and on the
LCD monitor screens, it means that the internal
battery has run down.
Recharge it by following the steps below.
Upon completion of charging, reset the date and
time.
Connect the AC adapter to the camera
recorder.
1
1
2
4
3
Return the viewfinder to its original position.
2
Leave the camera recorder’s POWER switch
at the OFF position.
3
Keep the camera recorder like this for about
4 hours.
4
OThe internal battery is charged during this
time.
28 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the electronic shutter
Shutter speeds which can be set
Shutter speeds which can be selected using SPEED SEL button
Standard (OFF)
shutter speed
Progressive mode
SYNCHRO SCAN
Shutter speed settings
OFF (50i)
25P
1/50
1/50
1/50.2 --- 1/248.0
1/25.1 --- 1/248.0
1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000
1/25, 1/60, 1/120, 1/250, 1/500, 1/1000
Each time the SHUTTER button is pressed,
the standard (OFF) shutter speed and the
shutter speed selected by the SPEED SEL
button are selected alternately.
1
2
1/ 1 2 0
After pressing the SHUTTER button, press
the SPEED SEL button to select the shutter
speed.
Each time the SPEED SEL button is
pressed, the shutter speed changes by one
setting in the following sequence.
If a setting other than OFF has been selected for the OTHER
DISPLAY item on the setting menu DISPLAY SETUP screen,
the current shutter speed setting is displayed in the viewfinder
and on the LCD monitor. However, it is not displayed if the
standard (OFF) shutter speed has been set.
When the progressive mode is OFF (50i)
SYNCHRO
SCAN
1/60
1/120
1/250
The luminance level of artificial lighting—
particularly that of fluorescent lights and
mercury lamps—changes in synchronization
with the power line frequency. Especially in
areas with a power line frequency of 60 Hz, the
vertical sync frequency (approx. 50 Hz) of the
camera recorder and frequency of the lighting
(60 Hz) will interfere with each other, possibly
causing the white balance to change cyclically.
When shooting under artificial lighting or when
adjusting the white balance, set the shutter
speed as shown below.
1/2000
1/1000
1/500
In the progressive mode (25P)
SYNCHRO
1/25
1/60
1/120
SCAN
1/1000
1/500
1/250
OThe higher the shutter speed, the lower
the sensitivity of the camera.
OWhen the iris is controlled automatically, it
opens more and more and the depth of
focus becomes shallower and shallower
as the shutter speed increases.
Shutter speed
Progressive mode
OEven when the SHUTTER button is
pressed while the slow shutter mode (see
page 30) is established, “INVALID”
appears in the viewfinder and on the LCD
monitor, and it is not possible to switch to
the above shutter speed.
60 Hz
50 Hz
OFF (50i)
25P
1/60
1/60
OFF (1/50)
OFF (1/50)
First, release the slow shutter mode using
the USER button to which SLOWSHUT
was allocated, and then set to the above
shutter speed.
29 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the electronic shutter
Slow shutter mode
OEven if the USER button to which
SLOWSHUT has been allocated is
pressed while the shutter speed set using
the SPEED SEL button is being used (see
page 29), “INVALID” appears in the
viewfinder and on the LCD monitor, and it
is not possible to switch to the slow shutter
mode.
Allocate SLOWSHUT to the USER1, USER2
or USER3 item from the setting menu SW
MODE screen. (See page 42)
1
The slow shutter mode is established by
2
First, set to the standard (OFF) status
using the SHUTTER button, and then
establish the slow shutter mode.
pressing the USER button to which
SLOWSHUT has been allocated. Each time
the SPEED SEL button is pressed, the
shutter speed changes in the sequences
shown below.
When the progressive mode is OFF (50i)
1/3
1/6
1/12
1/25
SLOW 1/
3
When the progressive mode is established (25P)
1/3
1/6
1/12
When a setting other than OFF has been selected for the
OTHER DISPLAY item on the setting menu DISPLAY SETUP
screen, the currently set slow shutter speed is displayed in the
viewfinder and on the LCD monitor screen.
OWhen the slow shutter mode is
established, “PROCESSING...” appears in
the viewfinder and on the LCD monitor for
the prescribed period, and the various
settings for the slow shutter mode are
performed.
OWhen the USER button to which
SLOWSHUT has been allocated is
pressed again, the slow shutter mode is
released, and operation returns to the
mode immediately before the slow shutter
mode was established.
OWhen the power is turned off and turned
back on while the slow shutter mode is
established, the normal mode is
established.
OThe gain cannot be controlled in the slow
shutter mode. It is controlled at the fixed
value (0 dB).
Synchro scan
The shutter speed of synchro scan used when
shooting TV screens or computer monitor
screens is set using the SYNCHRO SCAN item
on the setting menu CAMERA SETUP screen.
(See page 41)
OWhen the shutter is adjusted to suit the
frequency of a TV screen or computer
monitor screen, the horizontal noise that
occurs when shooting TV screens is
minimized.
The setting for progressive mode can be
switched with the PROGRESSIVE item on
the SCENE FILE screen of the setting menu.
(See page 41)
OThe slow shutter mode settings cannot be
changed or released during recording.
30 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
White balance and black balance
If it has not been possible to adjust the white
Adjusting the white balance
The white balance must always be re-adjusted
when the lighting conditions have changed.
balance automatically, an error message
appears in the viewfinder and on the LCD
monitor screen.
OWhen the ATW (Auto Tracking White)
function is operating, the white balance
cannot be adjusted automatically.
The white balance adjustment values can be
stored in the memory at the A and B positions of
the WHITE BAL switch.
Use A or B, whichever better suits the shooting
conditions concerned.
The 3200K and 5600K white balance values
have been stored in the memory at the PRST
position of the WHITE BAL switch.
Message that appears when adjustment is not
possible
AWB Ach NG
When the AWB button is pressed while the
WHITE BAL switch is at the PRST position, the
current white balance value is displayed.
When the AWB button is pressed again, the
3200K and 5600K white balance values are
selected alternately.
Error
Countermeasure
message
LOW LIGHT
Increase the amount of light. Alternatively,
boost the gain.
Use 3200K or 5600K, whichever better suits the
shooting conditions concerned when, for
instance, there is no time to adjust the white
balance.
LEVEL OVER Reduce the amount of light. Alternatively,
lower the gain.
If one of the above error messages has
appeared,
implement
the
suggested
countermeasure, and then try adjusting the
white balance again.
Set the shutter speed.
1
If the error message persists even after
repeated attempts at adjustment, consult your
dealer.
Place a white pattern in a location subject to
2
the same conditions as the lighting source of
the subject, zoom in on it, and fill the whole
screen with white.
A white object (white cloth or white wall) near
the subject may be used instead of the white
pattern.
OEnsure that there are no high-luminance
spotlights on the screen.
The WHITE BAL switch can be set to the A
or B position and white balance values here
can be stored in the memory.
3
Set the switch to the position (A or B) where
the white balance adjustment value is to be
stored, and press the AWB button.
OIt takes a few seconds to complete the
adjustment.
(The following messages appear on the
screen.)
Message that appears while adjustment is
underway
AWB Ach ACTIVE
Message that appears upon completion of the
adjustment
AWB Ach OK
31 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
White balance and black balance
Adjusting the black balance
ATW (Auto Tracking White)
function
There is normally no need to re-adjust the black
balance. Adjustment is required only in the
following cases.
OWhen the camera recorder is to be used for
the first time
The ATW function can be allocated to the
WHITE BAL switch (A, B or PRST position)
using the ATW item on the setting menu SW
MODE screen. (See page 42)
OWhen the camera recorder is to be used after
it has not been used for an extended period
OWhen the camera recorder is to be used in a
situation where the ambient temperature will
vary significantly
OWhen the standard (OFF) shutter speed or
slow shutter mode has been selected
OWhen the progressive mode has been
switched to the standard (50i) mode or vice
versa
Similarly, the ATW function can be allocated to
the AUTO button using the ATW item on the
setting menu AUTO SW screen. (See page 43)
When material is shot using the ATW function, it
is recorded while the white balance is being
continually adjusted automatically.
OThe ATW function automatically identifies the
shooting environment and adjusts the white
balance optimally. In some environments, a
slight adjustment error may arise.
If an extremely accurate white balance
adjustment is required, adjust the white
balance by following the instructions on the
previous page.
The white balance is adjusted automatically by
pressing the AWB button.
If the button is then held down, the black
balance is adjusted.
OWhen the AWB button is pressed, the white
balance is adjusted first. Therefore, ensure
that the conditions under which the white
balance is adjusted are satisfied before
pressing the button.
OWhile recording is in progress, the black
balance cannot be adjusted.
Message that appears while adjustment is
underway
ABB ACTIVE
Message that appears upon completion of the
adjustment
ABB END
32 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the time data
Setting the user’s bit
The screen shown below appears. Set the
user’s bit using the OPERATION lever.
Tilt the OPERATION lever in the 3 or 4
direction, select the user’s bit characters,
press “;” of the OPERATION lever, and
move to the next digit.
OThe numbers 0 to 9 and letters A to F can
be used as the user’s bit characters.
OWhen the COUNTER RESET button is
pressed on the screen shown below, the
user’s bit is reset to zero.
5
By setting the user’s bit, memos (dates, times)
and other information consisting of up to 8 digits
in hexadecimal notation can be recorded on the
sub-code track. The user’s bit settings are
automatically stored in the memory and retained
even after the power has been turned off.
Set the camera recorder’s POWER switch to
1
ON.
UBPRESET
Select USER as the setting for the UB
2
MODE item on the setting menu
RECORDING SETUP screen.
OFor details on the menu operations, refer
to page 38.
0000000
0
+:PUSHPLAY
–:PUSHSTOP
SEL:PUSHSTILL
RECORDINGSETUP
:
TCG
H FREERUN
H PRESET
H ––––
PUSHMENUTORETURN
FIRSTRECTC
TCPRESET
UBMODE
USER TIME
H
Upon completion of the user’s bit setting,
press the MENU button. The screen shown
below appears. Tilt the OPERATION lever
in the 4 direction, select YES, and press
“;” of the OPERATION lever.
6
7
DATE TCG FRM.RATE
UBPRESET
H ––––
;
PUSHMENUTORETURN
Tilt the OPERATION lever in the 4 direction
and move to the UB PRESET item.
UBPRESET
3
4
PRESETOK?
RECORDINGSETUP
:
NO –––. PUSHSTILL
YES
TCG
H FREERUN
FIRSTRECTC
H PRESET
TCPRESET
UBMODE
H ––––
H USER
––––YES
H
UBPRESET
;
PUSHMENUTORETURN
Press the MENU button twice to release the
menu mode.
Press “;” of the OPERATION lever, and
move “1” to YES.
RECORDINGSETUP
:
TCG
H FREERUN
FIRSTRECTC
H PRESET
TCPRESET
UBMODE
H ––––
H USER
––––YES
H
UBPRESET
;
PUSHMENUTORETURN
33 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the time data
Setting the time code
Press “;” of the OPERATION lever, and
move “1” to YES.
4
5
The various settings related to the time code are
performed using the following items on the
setting menu RECORDING SETUP screen.
OTCG item
OFIRST REC TC item
OTC PRESET item
TCPRESET
:
TCG
H FREERUN
FIRSTRECTC
H PRESET
––––YES
H USER
H
TCPRESET
UBMODE
O1394 TC REGEN item (appears in the VCR
mode)
UBPRESET
H ––––
;
For further details, refer to page 45.
PUSHMENUTORETURN
OWhen ON has been selected as the setting
for the 1394 TC REGEN item in the VCR
mode, the settings of the items listed above
cannot be changed.
The screen shown below appears. Set the
time code value using the OPERATION
lever.
Tilt the OPERATION lever in the 3 or 4
direction, select the time code value, press
“;” of the OPERATION lever, and move to
the next digit.
OWhen the COUNTER RESET button is
pressed on the screen shown below, the
time code value is reset to zero.
How to select the TC PRESET item setting
When the time code at the start of the recording
is to be recorded using the value specified by
the user as its initial value, set the time code
value using the TC PRESET item.
Set the camera recorder’s POWER switch to
1
TCPRESET
ON.
0h00m00s00f
0
Select PRESET as the setting for the FIRST
2
REC TC item on the setting menu
RECORDING SETUP screen.
OFor details on the menu operations, refer
to page 38.
+:PUSHPLAY
–:PUSHSTOP
SEL:PUSHSTILL
TCPRESET
PUSHMENUTORETURN
:
TCG
H FREERUN
Upon completion of the time code value
setting, press the MENU button. The screen
shown below appears. Tilt the OPERATION
lever in the 4 direction, select YES, and
press “;” of the OPERATION lever.
6
7
REGEN
FIRSTRECTC
PRESET
H
TCPRESET
UBMODE
H ––––
H USER
UBPRESET
H ––––
;
PUSHMENUTORETURN
TCPRESET
Tilt the OPERATION lever in the 4 direction
and move to the TC PRESET item.
PRESETOK?
3
NO –––. PUSHSTILL
YES
TCPRESET
:
TCG
H FREERUN
FIRSTRECTC
H PRESET
––––YES
H USER
H
TCPRESET
UBMODE
Press the MENU button twice to release the
menu mode.
UBPRESET
H ––––
;
PUSHMENUTORETURN
34 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Scene files
The settings selected to suit various shooting
situations are stored in the positions of the
scene file dial. During shooting, the required file
can be read out in an instant using this dial.
F1: SCENE
File containing the settings suited to
standard shooting
F2: SCENE FLUO.
File containing the settings suited to
shooting where consideration is given to
the characteristics of fluorescent lights (for
shooting indoors, etc.)
The following files were stored as factory
settings prior to shipment.
OEven when a scene file has been changed
during recording, the progressive mode will
not be changed.
To change this mode, establish the recording
standby mode.
F3: SCENE SPARK
File containing the settings suited to
shooting for accentuating the subjects (for
shooting wedding receptions, etc.)
F4: SCENE B-STR
File containing the settings suited to
shooting with extended gradations for the
dark areas (for shooting scenes at dusk,
etc.)
F5: SCENE 25P
File containing the settings suited to
cinema-like shooting using the progressive
25P mode
(The V DETAIL FREQ item on the SCENE
FILE setting menu screen is set to THICK.)
F6: SCENE CINE
File containing the settings suited to
cinema-like shooting using the progressive
25P mode
(The V DETAIL FREQ item on the SCENE
FILE setting menu screen is set to THIN.)
35 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Scene files
Changing the scene file settings
The screen shown below appears. Set a
filename consisting of six characters using
the OPERATION lever.
OCharacters which can be set
) (space), letters A to Z, numbers 0 to 9,
6
Scene file settings can be changed.
In addition, scene files in which changes have
been made can be stored in the positions of the
scene file dial.
:, ;, <, =, >, ?, @, [, ¥, ], ^, _
NAMEEDIT
Set the camera recorder’s POWER switch to
ON.
1
SWPOSITIONF1
Turn the scene file dial, and select the scene
file in which changes are to be made.
2
+:PUSHPLAY
–:PUSHSTOP
SEL:PUSHSTILL
Change the item on the setting menu
SCENE FILE screen.
3
PUSHMENUTORETURN
OFor details on the menu operations, refer
to page 38.
Upon completion of the filename setting,
press the MENU button.
7
8
Tilt the OPERATION lever in the 4 direction
and move to the NAME EDIT item.
4
Tilt the OPERATION lever in the 4 direction
and move to the SAVE/INIT item.
SCENEF1:
:
SCENEF1:222222
VDETAILFREQ THIN
:
VDETAILFREQ THIN
PROGRESSIVE
H OFF
––––YES
H ––––
H
PROGRESSIVE
H OFF
NAMEEDIT
SAVE/INIT
NAMEEDIT
SAVE/INIT
H ––––
––––YES
H
PUSHMENUTORETURN
PUSHMENUTORETURN
Press “;” of the OPERATION lever, and
move “1” to YES.
5
Press “;” of the OPERATION lever, and
move “1” to YES.
9
SCENEF1:
:
SCENEF1:222222
VDETAILFREQ THIN
:
VDETAILFREQ THIN
PROGRESSIVE
H OFF
––––YES
H
PROGRESSIVE
H OFF
NAMEEDIT
SAVE/INIT
H ––––
NAMEEDIT
SAVE/INIT
H ––––
––––YES
H
PUSHMENUTORETURN
PUSHMENUTORETURN
36 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Scene files
The screen shown below appears. Press
“;” of the OPERATION lever, and move
“1” to YES.
To return the scene file settings to the factory
settings, select INITIAL in step 10, and then
perform the same steps 11 to 13.
10
FILEF1:222222
––––YES
H
SAVE
INITIAL
H ––––
PUSHMENUTORETURN
The screen shown below appears. Tilt the
OPERATION lever in the 4 direction,
select YES, and press “;” of the
OPERATION lever.
11
FILEF1:222222
SAVE?
.
––– PUSHSTILL
NO
YES
A beep sounds ten times in succession,
the following message appears, and the
scene file changes are completed.
12
13
SAVE
COMPLETED!
Press the MENU button three times to
release the menu mode.
If the menu mode is released without saving
the changes, the original scene file settings
will be restored when operation is switched to
the VCR mode or the power is turned off.
37 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
The camera recorder’s settings can be changed
to suit the scenes to be shot or what is to be
recorded using the setting menus.
Tilt the OPERATION lever in the 3 or 4
direction, and move the highlighted part to
the function which is to be set.
4
(If the remote control unit is used, press the
“V” or “B” button among the SET buttons.)
Operation method
Example:
In any operation mode except the shooting
mode or recording mode, press the MENU
button.
The menu mode is established, and the
function screen shown below appears in the
viewfinder and on the LCD monitor.
1
OTHERFUNCTIONS
REMOTE
HVCR1
DVCONTROL HOFF
DVCMDSEL HRECP
OFF FRONT
REAR BOTH
RECLAMP
[Camera mode]
H
BEEPSOUND HON
CAMERAMENU
;
PUSHMENUTORETURN
1.SCENEFILE
2.CAMERASETUP
3.SWMODE
Press “;” of the OPERATION lever, and
4.AUTOSW
5
5.RECORDINGSETUP
6.DISPLAYSETUP
7.OTHERFUNCTIONS
move “ ” to the setting which is to be
1
changed.
(If the remote control unit is used, press the
“M” button among the SET buttons.)
PUSHMENUTOEXIT
[VCR mode]
To change a numerical value, for example,
move “ ” to the position of the value to be
1
VCRFUNCTIONS
changed, tilt the OPERATION lever in the 3
1.PLAYBACKFUNCTIONS
2.RECORDINGSETUP
3.AVIN/OUTSETUP
4.DISPLAYSETUP
or 4 direction, and change the setting.
(If the remote control unit is used, press the
“V” or “B” button among the SET buttons.)
5.OTHERFUINCTIONS
Example:
OTHERFUNCTIONS
PUSHMENUTOEXIT
REMOTE
HVCR1
DVCONTROL HOFF
Tilt the OPERATION lever in the 3 or 4
direction, and move the highlighted part to
the function which is to be set.
(If the remote control unit is used, press the
“V” or “B” button among the SET buttons.)
2
DVCMDSEL HRECP
OFF FRONT
H
RECLAMP
REAR BOTH
BEEPSOUND HON
;
PUSHMENUTORETURN
Press “;” of the OPERATION lever, and
display the setting item.
(If the remote control unit is used, press the
“M” button among the SET buttons.)
3
6 To change another item, repeat steps 4 and
5.
To exit the settings, press the MENU button
to return to the function screen.
Example:
OTHERFUNCTIONS
7 To change another function, repeat steps 2
VCR1VCR2
to 5.
H
REMOTE
OFF
To exit the menu mode, press the MENU
button to return to the normal screen.
DVCONTROL HOFF
DVCMDSEL HRECP
RECLAMP
HBOTH
BEEPSOUND HON
;
PUSHMENUTORETURN
38 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
Configuration of setting menus
Menus in the camera mode
SCENE FILE
DETAIL LEVEL
V DETAIL LEVEL
DETAIL CORING
CHROMA LEVEL
CHROMA PHASE
COLOUR TEMP
MASTER PED
A. IRIS LEVEL
GAMMA
CAMERA SETUP
SYNCRO SCAN
ASPECT CONV
COLOUR BAR
SW MODE
MID GAIN
HIGH GAIN
ATW
HANDLE ZOOM
IRIS DIAL
USER1
KNEE
MATRIX
SKIN TONE DTL
V DETAIL FREQ
PROGRESSIVE
NAME EDIT
USER2
USER3
AUTO SW
A. IRIS
AGC
ATW
AF
SAVE/INIT
RECORDING SETUP
DISPLAY SETUP
REC SPEED
AUDIO REC
MIC ALC
MIC GAIN 1
MIC GAIN 2
TCG
FIRST REC TC
TC PRESET
UB MODE
ZEBRA DETECT 1
ZEBRA DETECT 2
MARKER
VIDEO OUT OSD
DATE/TIME
LEVEL METER
ZOOM•FOCUS
TAPE•BATTERY
OTHER DISPLAY
LCD BACKLIGHT
LCD SET
UB PRESET
INTERVAL REC
REC TIME
INTERVAL TIME
EVF SET
SELF SHOOT
EVF MODE
EVF COLOUR
OTHER FUNCTIONS
REMOTE
DV CONTROL
DV CMD SEL
REC LAMP
BEEP SOUND
CLOCK SET
TIME SHIFT
TAPE PROTECT
USER FILE
HOUR METER
Menus in the VCR mode
PLAYBACK FUNCTIONS
END SEARCH
32K(12bit)AUDIO
AUDIO OUT
RECORDING SETUP
AV IN/OUT SETUP
REC SPEED
AUDIO REC
1394 TC REGEN
TCG
A DUB INPUT
DV OUT
DISPLAY SETUP
DATE/TIME
FIRST REC TC
TC PRESET
1394 UB REGEN
UB MODE
LEVEL METER
TAPE•BATTERY
OTHER DISPLAY
VIDEO OUT OSD
CAMERA DATA
LCD BACKLIGHT
LCD SET
UB PRESET
EVF SET
EVF MODE
OTHER FUNCTIONS
REMOTE
CLOCK SET
TIME SHIFT
USER FILE
HOUR METER
39 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
SCENE FILE screen
Item/
(display mode)
Item/
(display mode)
Description of settings
Description of settings
DETAIL LEVEL
(Camera)
For adjusting the detail amount.
–7 --- 0 --- +7
GAMMA
(Camera)
For selecting the gamma curve.
LOW:
Using a gamma curve with a moderate
gradient for the low-luminance areas, the
images are given a calm, composed look.
A sharp touch is conveyed by the contrast.
NORM:
V DETAIL
(Camera)
For adjusting the strength of the outline
compensation in the vertical direction of the
images.
–7 --- 0 --- +7
DTL CORING
(Camera)
For adjusting the level at which the noise in
the detail signals is to be eliminated.
–7 --- 0 --- +7
When this is adjusted in the “–” direction,
clearer images are produced but the noise
increases slightly.
Standard images are produced.
HIGH:
Using a gamma curve with a sharp
gradient for the low-luminance areas, the
gradations of the dark areas are
extended to make them appear brighter.
A soft touch is conveyed by the contrast.
B.PRESS:
When it is adjusted in the “+” direction, the
noise decreases.
Images giving the sense of a sharper contrast
than at the LOW setting are produced.
CINE-LIKE:
CHROMA LEVEL For adjusting the chroma level.
(Camera)
–7 --- 0 --- +7
CHROMA
PHASE (Camera) –7 --- 0 --- +7
For finely adjusting the chroma phase.
The gamma curve which gives the
images a cinema-like finish is used.
Images with less noise than at the
CINE_LIKE_D setting are produced.
CINE-LIKE_D:
COLOUR TEMP
(Camera)
For finely adjusting the colour temperature
(for performing fine adjustments after the
white balance has been adjusted).
–7 --- 0 --- +7
The dynamic range is higher than at the
CINELIKE setting.
MASTER PED
(Camera)
For adjusting the black master pedestal
which serves as the video reference.
–15 --- 0 --- +15
CINE-LIKE_V:
This uses the gamma curve for finishing
the images into movie-like images where
priority is given to contrast.
A. IRIS LEVEL
(Camera)
For setting the auto iris target value.
–4 --- 0 --- +4
In order to make full use of the CINE-
LIKE gamma characteristics, it is
recommended that the lens iris be set
lower (by approx. 1/2) than the regular
video level.
KNEE
(Camera)
For setting the level (knee point) at which
the high-brightness video signals sensed by
the CCD are to be compressed in order to
minimize colour saturation in the highlights
of the image.
AUTO: The knee point is set automatically in
accordance with the signals sensed.
LOW: The knee point is set on the low side
(with compression starting from
around 80%).
MID: The knee point is set at an interim value
(with compression starting from around
90%).
HIGH: The knee point is set on the high side
(with compression starting from around
100%).
MATRIX
(Camera)
For selecting the matrix table and
expressing the colours during shooting.
NORM1:
Colors suited to shooting
outdoors or under light sources
using halogen lamps are
expressed.
NORM2:
FLUO:
More vivid colors are expressed
than with the NORM1 setting.
Colours suited to shooting
indoors under fluorescent light
sources are expressed.
CINE-LIKE: Colours suited to cinema-like
The underlining indicates the factory setting.
shooting are expressed.
40 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
SCENE FILE screen
CAMERA SETUP screen
Item/
(display mode)
Item/
(display mode)
Description of settings
Description of settings
SKIN TONE DTL For switching the skin tone detail ON or
SYNCRO SCAN
(Camera)
For adjusting the shutter speed of synchro
scan used when shooting TV screens, etc.
If the OPERATION lever is left tilted in the
3 or 4 direction, the speed at which the
setting changes is increased, and a beep is
heard.
(Camera)
OFF.
When ON is selected, the detail in the skin
tone areas is diminished and the graininess
of the skin is reduced.
OFF
ON
O Progressive mode OFF:
1/50.2 --- 1/248.0
O Progressive mode 25P:
1/25.1 --- 1/50.0 --- 1/248.0
V DETAIL FREQ For setting the detail in the vertical direction
(Camera)
when shooting in the progressive mode.
THIN
MID
:
:
The detail is made finer.
The detail is made somewhat coarser.
THICK : The detail is made coarser.
ASPECT CONV
(Camera)
For selecting the aspect ratio of the images
to be recorded.
NORM:
The images are recorded in the standard
4:3 mode.
O When “THIN” or “MID” has been selected
as the item’s setting and the images shot
in the progressive mode are played back
using
a
standard TV monitor (50i:
interlace), some flickering will occur on
the horizontal lines and on the diagonal
lines near the horizontal.
LETTER BOX:
The aspect ratio is set to the 16:9 mode,
and the images are recorded in this
mode. Black bands are recorded at the
top and bottom of the screen.
SQUEEZE:
The camera images are compressed
horizontally so that they will be displayed
optimally on a 16:9 monitor.
When playing back
a
tape in
a
progressive environment, this flickering
is reduced by selecting “THIN” or “MID”
as the item’s setting, which will also
enable images with a higher resolution
than that with the “THICK” setting to be
obtained.
<Note>
The images appearing in the viewfinder and
on the LCD monitor may be disrupted for a
moment when SQUEEZE is selected as the
item setting; this is normal and not
indicative of malfunctioning.
PROGRESSIVE
(Camera)
For setting shooting in the progressive
mode.
OFF:
Shooting is not performed in the
progressive mode.
25P:
COLOUR BAR
(Camera)
For setting the colour bar display to ON or
OFF.
Shooting is performed in the 25P mode
(25 frames/sec.).
OFF
ON
O Even when the colour bar display has
been set to ON, it will return to OFF
when operation is switched to the VCR
mode or the power is turned off.
NAME EDIT
(Camera)
For editing the name of the scene file
selected by the scene file dial.
SAVE/INIT
(Camera)
SAVE:
For saving the scene file settings after
changes have been made to them.
O If the menu mode is released without
saving the changes, the original scene
file settings will be restored when
operation is switched to the VCR mode
or the power is turned off.
INITIAL:
For returning the scene file settings
selected by the scene file dial to the factory
settings.
The underlining indicates the factory setting.
41 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
SW MODE screen
Item/
(display mode)
Item/
(display mode)
Description of settings
Description of settings
MID GAIN
(Camera)
For setting the gain value which is to be
allocated to the M position of the GAIN
switch.
USER1
(Camera)
For setting the operation of the function
allocated to the USER1 button.
COLOUR BAR:
The colour bar display is set to ON or OFF.
SPOTLIGHT:
The auto iris control for the spotlight is
set to ON or OFF.
BACKLIGHT:
The auto iris control for backlight
compensation is set to ON or OFF.
BLACKFADE:
When the button is held down, the whole
image is faded out into black. The sound
is also faded out at the same time.
WHITEFADE:
0 dB, 3 dB, 6 dB, 9 dB, 12 dB
HIGH GAIN
(Camera)
For setting the gain value which is to be
allocated to the H position of the GAIN
switch.
0 dB, 3 dB, 6 dB, 9 dB, 12 dB
ATW
(Camera)
For setting the ATW (Auto Tracking White)
function which is to be allocated to the
WHITE BAL switch.
OFF:
The ATW function is not activated.
However, if it has been set in the AUTO
button or USER button, it will follow the
operation of the button concerned.
Ach:
When the button is held down, the whole
image is faded out into white. The sound
is also faded out at the same time.
MODECHECK:
The ATW function is activated when the
WHITE BAL switch has been set to the A
position.
When the button is pressed, the camera
status currently set is displayed in the
viewfinder and on the LCD monitor
where it can be checked.
Bch:
ATW:
The ATW function is activated when the
WHITE BAL switch has been set to the B
position.
The operation of the ATW function is set
to ON or OFF.
ATWLOCK:
When the button is pressed, the white
balance value is fixed; when it is pressed
again, the operation of the ATW function
is performed.
PRE:
The ATW function is activated when the
WHITE BAL switch has been set to the
PRST position.
HANDLE ZOOM For setting the zoom speeds which are to
GAIN:18 dB:
When this button is pressed, the gain is
set to 18 dB.
O The picture may be temporarily
disturbed when the gain has been
switched to 18 dB or from 18 dB to
another value.
(Camera)
be allocated to the positions of the
HANDLE ZOOM switch.
L/OFF/H:
LOW/OFF/HIGH are set to the 1/2/3
positions. (At OFF, no zoom operations
are performed.)
INDEX:
L/M/H:
When the button is pressed during
shooting or recording, an index signal is
recorded on the tape. If it is pressed while
shooting or recording is temporarily
stopped, the index signal recording
LOW/MID/HIGH are set to the 1/2/3
positions.
IRIS DIAL
(Camera)
For setting the rotational direction of the
IRIS dial and iris control (in the MANUAL
IRIS mode).
standby mode is established.
When
shooting or recording is commenced from
this mode, the index signal will be recorded
on the tape. Recording index signals
enables index searches to be performed
during playback. (See page 62)
DOWN OPEN:
The iris opens when the IRIS dial is
turned downward.
UP OPEN:
The iris opens when the IRIS dial is
turned upward.
SLOWSHUT:
When the button is pressed, the slow
shutter mode is established. Each time
it is pressed, the mode is turned ON or
OFF alternatively.
USER2
(Camera)
For setting the operation of the function to
be allocated to the USER2 button.
The settings are the same as for the ones
for the USER1 items.
BACKLIGHT
USER3
(Camera)
For setting the operation of the function to
be allocated to the USER3 button.
The settings are the same as for the ones
for the USER1 items.
INDEX
The underlining indicates the factory setting.
42 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
AUTO SW screen
PLAYBACK FUNCTIONS screen
Item/
(display mode)
Item/
Description of settings
Description of settings
(display mode)
A. IRIS
(Camera)
ON:
END SEARCH
(VCR)
For setting what kind of operation is to be
performed when the EVF DTL/END
SEARCH button is pressed.
BLANK:
The unrecorded blanks on the video tape
are searched.
When the AUTO button is pressed, the
auto iris control operation is performed.
The IRIS button does not work at this
time.
OFF:
The auto iris control operation is not
performed even if the AUTO button is
pressed.
REC END:
The part which was shot last is
searched.
The iris control operation selected by the
IRIS button is performed.
<Notes>
O Even when the REC END setting is
selected, the part which was shot last
will not be searched when the tape is
switched.
O If nothing has been recorded on the
tape, operation will stop at the end of the
tape.
O END SEARCH may not operate properly
if there is an unrecorded blank near the
tape start or at a point along the tape.
AGC
(Camera)
For setting the auto gain control operation
when ON is selected as the A. IRIS item
setting.
6 dB:
Auto gain control up to 6 dB is performed
when the AUTO button is pressed.
12 dB:
Auto gain control up to 12 dB is
performed when the AUTO button is
pressed.
32K (12bit)
AUDIO
For setting the sound to be output as the
CH1 and CH2 signals when
a
tape
OFF:
(VCR)
recorded in the 32K (12-bit) audio mode is
played back.
Auto gain control is not performed even
if the AUTO button is pressed.
ST1:
ATW
ON:
The sound recorded during shooting is
selected.
CH1 signals = CH1 track
CH2 signals = CH2 track
ST2:
The sound recorded during audio
dubbing is selected.
CH1 signals = CH3 track
CH2 signals = CH4 track
MIX:
The sound recorded during shooting and
the sound recorded during audio
dubbing are mixed.
CH1 signals = CH1 + CH3 tracks
CH2 signals = CH2 + CH4 tracks
<Note>
If the sound has been recorded in the 48K
(16-bit) mode, there is no CH3 or CH4.
Therefore, the correlation between the
signals and tracks will always be as follows:
CH1 signals = CH1 track
CH2 signals = CH2 track
(Camera)
The ATW (auto tracking white balance)
function operation is set to ON or OFF
using the AUTO button.
At this time, the operation of this function
cannot be set to ON or OFF using the
WHITE BAL switch and USER button.
However, when ATWLOCK is allocated
to the USER button, the white balance
value can be fixed using the USER
button.
OFF:
The ATW function operation is not
performed even if the AUTO button is
pressed.
The ATW function operation selected by
the WHITE BAL switch is performed.
AF
(Camera)
ON:
When the AUTO button has been
pressed, the auto focus operation is
performed.
The FOCUS switch and PUSH AUTO
button do not work at this time.
OFF:
The auto focus operation is not
performed even if the AUTO button is
pressed.
The focus operation selected by the
FOCUS switch and PUSH AUTO button
is performed.
The underlining indicates the factory setting.
43 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
PLAYBACK FUNCTIONS screen
RECORDING SETUP screen
Item/
Item/
Description of settings
(display mode)
Description of settings
(display mode)
AUDIO OUT
(VCR)
For setting the audio signals to be output
from the AUDIO IN/OUT connectors (pin
jacks) when a tape is played back.
CH1•CH2:
CH1 connector = CH1 signals
CH2 connector = CH2 signals
CH1:
CH1 connector = CH1 signals
CH2 connector = CH1 signals
CH2:
CH1 connector = CH2 signals
CH2 connector = CH2 signals
REC SPEED
(Camera)
(VCR)
For selecting the recording time mode.
SP : SP (standard play) mode
LP : LP (long play) mode
AUDIO REC
(Camera)
(VCR)
For selecting the system for converting the
recording to PCM audio.
32K (12 bit)
48K (16 bit)
:
:
12-bit/32kHz
16-bit/48kHz
MIC ALC
(Camera)
For setting the mic level automatic control
function to ON or OFF.
OFF
ON
Audio distortion caused by excessively high
input level can be minimized by selecting
ON for this item.
O The recording level of the audio signals
must be adjusted using the AUDIO
controls, irrespective of this setting.
Inputs and audio tracks recorded
When audio dubbing
(12-bit mode)
Input
When shooting
MIC GAIN 1
(Camera)
For setting the input level of the external
microphone which is connected to the
INPUT 1 connector.
Internal
microphone L
CH1
CH2
CH3
CH4
-50 dB
-60 dB
Internal
microphone R
MIC GAIN 2
(Camera)
For setting the input level of the external
microphone which is connected to the
INPUT 2 connector.
INPUT 1 (XLR)
INPUT 2 (XLR)
CH1
CH3
CH2 (CH1)
CH4 (CH3)
-50 dB
-60 dB
AUDIO IN/OUT
CH1 (pin jack)
__
__
CH3
CH4
AUDIO IN/OUT
CH2 (pin jack)
The audio tracks on which signals are to be recorded during
shooting can be changed using the CH1 SELECT switch and
CH2 SELECT switch.
The audio tracks on which signals are to be recorded during
audio dubbing can be changed using the A DUB INPUT item
on the AV IN/OUT SETUP screen.
32K (12-bit) AUDIO item and AUDIO OUT item settings, and audio tracks
whose signals are output from the AUDIO IN/OUT connectors (pin jacks)
32K (12-bit) AUDIO
item setting
AUDIO OUT
item setting
AUDIO IN/OUT
CH1 output
AUDIO IN/OUT
CH2 output
Audio recording
mode
CH1•CH2
CH1
CH2
CH1
CH1
CH2
CH2
CH1
CH2
ST1
CH1•CH2
CH1
CH2
CH3
CH3
CH4
CH4
CH3
CH4
32K (12 bit)
48K (16 bit)
ST2
MIX
CH1+CH3
CH2+CH4
__
CH1•CH2
CH1
CH2
CH1
CH1
CH2
CH2
CH1
CH2
__
The underlining indicates the factory setting.
44 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
RECORDING SETUP screen
Item/
Item/
(display mode)
Description of settings
(display mode)
Description of settings
1394 TC REGEN For selecting the time code to be recorded
1394 UB REGEN For selecting the user’s bit to be recorded
(VCR)
when recording the signals of a component
connected to the DV connector.
OFF:
(VCR)
when recording the signals of the
component connected to the DV connector.
OFF:
The signals are recorded using the time
code which was set using the TC MODE
item, TCG item and FIRST REC TC
item.
The user’s bit selected for the UB MODE
item is used for the recording.
ON:
The user’s bit of the signals input to the
DV connector is used for the recording.
ON:
The signals are recorded using the time
code of the signals which have been
input to the DV connector.
O
When ON has been selected as this item’s
setting, this setting takes precedence over
the UB MODE item setting.
O When ON has been selected as this
item’s setting, this setting takes
precedence over the TC MODE item,
TCG item and FIRST REC TC item
settings.
O When no signals are supplied to the DV
connector, the TC MODE item, TCG item
and FIRST REC TC item settings are
followed.
O The user’s bit is not recorded if the
signals do not contain the user’s bit
information.
O When no signals are supplied to the DV
connector, the UB MODE item setting is
followed.
UB MODE
(Camera)
(VCR)
For setting what is to be recorded as the
user’s bit.
USER:
TCG
(Camera)
(VCR)
For setting the operation mode in which the
internal time code generator is to be run.
FREE RUN:
The user’s information is recorded.
TIME:
The time of the recording is recorded.
The internal time code generator is run
regardless of the operation mode.
REC RUN:
The internal time code generator is run
during recording.
22 22 22 00
Hours
Minutes
Seconds
DATE:
The date of the recording is recorded.
FIRST REC TC
(Camera)
(VCR)
For selecting the time code which is to be
recorded when recording is started.
REGEN:
Recording proceeds in such a way that
the time code continues on (is
regenerated) from the time code on the
tape.
22 22 22 22
Year
Month
Hours
Day
TCG:
The time code generator’s value is
recorded.
FRM. RATE:
PRESET:
The frame rate information for frame
conversion is recorded.
The time code is not regenerated from
the time code on the tape.
The time code is recorded using the
value set in the TC PRESET item
serving as the initial value.
However, the time code is forcibly
regenerated when shooting with frame-
to-frame continuity has been performed.
22 0F 22 22
Recording control
information
O Updated frame information
O REC START/STOP
information
TC PRESET
(Camera)
(VCR)
For setting the initial value of the time code
to be recorded.
This item’s setting is valid when PRESET
has been selected as the setting for the
FIRST REC TC item.
O When the progressive mode has been
set to 24P or 24P (ADV), set the frame
value to 0 or to a multiple of 5. If any
other value is set, the time code
recorded will shift.
Frame rate information
O Frame rate (50 or 25)
O I/P identification information
O Frame rate coefficient
User’s bit value verification
information
UB PRESET
(Camera)
(VCR)
For setting the user’s bit. However, USER
must be selected for the UB MODE item
setting.
The underlining indicates the factory setting.
45 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
RECORDING SETUP screen
AV IN/OUT SETUP screen
Item/
Item/
Description of settings
(display mode)
Description of settings
(display mode)
INTERVAL REC
(Camera)
For setting the intermittent recording mode.
OFF: Intermittent recording is not performed.
ON: When the START/STOP button is
pressed, intermittent recording is
A DUB INPUT
(VCR)
For selecting the sound which is to be
recorded when audio dubbing is performed.
MIC: The sound from the internal microphone
or the sound from the external
performed with the cycle set by the REC
TIME item and INTERVAL TIME item.
ONE-SHOT: The time lapse shooting mode is
established.
components connected to the INPUT 1
and 2 connectors is recorded. (The
sound is selected using the CH1 SELECT
switch and CH2 SELECT switch.)
When the START/STOP button is
pressed, recording is performed for the
number of seconds set by the REC TIME
item, after which the recording pause
mode is established.
When intermittent recording is set to ON or
ONE-SHOT, “I –” flashes on the left of the
VCR operation mode. When recording is
started, it stops flashing and lights.
O Even when intermittent recording is set to
ON or ONE-SHOT, the intermittent
recording mode returns to OFF when the
power is turned off.
A_IN: The sound of the audio component
connected to the AUDIO IN/OUT
connectors (pin jacks) is recorded.
<Note>
If audio dubbing is performed when the
sound has been recorded in the 16-bit
audio mode, the sound will be recorded
over the sound heard during shooting.
O
DV OUT
(VCR)
For setting the function, which converts the
analogue signals which have been input
into digital signals and outputs them from
the DV connector, to ON or OFF.
OFF
ON
REC TIME
(Camera)
For setting the recording duration for which
intermittent recording is to be performed.
0.5s
1.5s
:
:
0.5 sec.
1.5 sec.
1s
2s
:
:
1.0 sec.
2.0 sec.
INTERVAL TIME For setting the duration of the interval time
(Camera)
with which intermittent recording is to be
performed.
15s
1m
:
:
15 sec.
1 min.
30s
5m
:
:
30 sec.
5 min.
10m : 10 min.
The underlining indicates the factory setting.
46 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
DISPLAY SETUP screen
Item/
(display mode)
Item/
(display mode)
Description of settings
Description of settings
ZEBRA DETECT For setting the level of the zebra pattern
CAMERA DATA When ON is set, the camera information
1
leaning to the left and displayed in the
viewfinder and on the LCD monitor.
80%, 85%, 90%, 95%, 100%, 105%
(VCR)
(such as camera shake correction, iris
value and gain value) is displayed when the
tape is played back.
(Camera)
OFF
ON
ZEBRA DETECT For setting the level of the zebra pattern
2
leaning to the right and displayed in the
viewfinder and on the LCD monitor.
80%, 85%, 90%, 95%, 100%, 105%, OFF
<Note>
LCD
For adjusting the backlight of the LCD
monitor.
When HI is set, the monitor becomes
brighter than usual.
(Camera)
BACKLIGHT
(Camera)
(VCR)
When OFF has been set, the zebra pattern
is not displayed.
HI
NORMAL
LCD SET
(Camera)
(VCR)
For adjusting the display level of the LCD
monitor images.
LCD COLOUR LEVEL:
MARKER
(Camera)
For switching display of the marker
ON/OFF.
ON
OFF
The colour level of the LCD monitor’s
images is adjusted.
O When ON is set, the marker can be
displayed by pressing the ZEBRA
button.
LCD BRIGHTNESS:
The brightness of the LCD monitor’s
images is adjusted.
When the marker is displayed, the video
level of the image near the centre of the
screen is displayed as a percentage
value at the bottom left of the screen.
LCD CONTRAST:
The contrast of the LCD monitor’s
images is adjusted.
EVF SET
(Camera)
(VCR)
For adjusting the display level of the
viewfinder images.
EVF COLOUR LEVEL:
The colour level of the viewfinder’s
images is adjusted.
EVF BRIGHTNESS:
VIDEO OUT OSD When ON is set, the information displayed
(Camera)
(VCR)
in the viewfinder and on the LCD monitor is
output as the video output signal together
with the images.
ON
OFF
The brightness of the viewfinder’s
images is adjusted.
EVF CONTRAST:
The contrast of the viewfinder’s images
is adjusted.
DATE/TIME
(Camera)
(VCR)
For setting the date and/or time to be
displayed in the viewfinder, on the LCD
monitor and in the video output signals.
OFF:
The date and time are not displayed.
TIME:
The time is displayed.
DATE:
The date is displayed.
TIME&DATE:
Both the date and time are displayed.
O When
a
setting other than OFF is
selected, the date and/or time are
displayed in the video output signals
regardless of the setting selected for the
VIDEO OUT OSD item.
LEVEL METER
(Camera)
(VCR)
For setting the audio level meter display to
ON or OFF.
OFF
ON
ZOOM•FOCUS
(Camera)
For setting the zoom and focus value
displays to ON or OFF.
OFF
ON
TAPE•BATTERY
(Camera)
(VCR)
For setting the remaining tape amount and
remaining battery charge displays to ON or
OFF.
OFF
ON
OTHER
DISPLAY
(Camera)
(VCR)
For setting the amount of information to be
displayed in the viewfinder and on the LCD
monitor. (See page 56)
OFF, PARTIAL, ALL
The underlining indicates the factory setting.
47 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
DISPLAY SETUP screen
OTHER FUNCTIONS screen
Item/
(display mode)
Item/
Description of settings
Description of settings
(display mode)
SELF SHOOT
(Camera)
For selecting the LCD monitor’s mirror
function for face-to-face shooting. When
MIRROR is set, the image on the LCD
monitor is reversed at the left and right for
display during face-to-face shooting.
REMOTE
(Camera)
(VCR)
For setting the operations which are
performed using the accessory wireless
remote control unit. (See page 19 for the
remote control unit settings.)
VCR1: The operation performed by the
remote control unit which has been set
to be used for VCR1 are accepted.
VCR2: The operation performed by the
remote control unit which has been set
to be used for VCR2 are accepted.
OFF: Operations performed by the remote
control unit are not accepted.
NORMAL
MIRROR
EVF MODE
(Camera)
(VCR)
For selecting what is to be displayed in the
viewfinder and on the LCD monitor.
ON:
Images are shown at all times in the
viewfinder.
AUTO:
When the LCD monitor is opened, the
DV CONTROL
(Camera)
For setting the control method when
backup shooting is to be performed by
images no longer appear
viewfinder.
in the
connecting
a
component for backup
purposes to the DV connector.
OFF: The component for backup purposes
is not controlled.
EXT: The component for backup purposes
is controlled using the START/STOP
button on the camera recorder. The
images shot by the camera recorder are
recorded by the component for backup
purposes.
EVF COLOUR
(Camera)
For selecting colour or monochrome for the
viewfinder display.
ON:
Colour display
OFF
Monochrome display
However, the camera recorder does not
record the images.
BOTH: The images shot by the camera
recorder are recorded by both camera
recorder and the component for backup
purposes.
CHAIN: When the tape in the camera
recorder approaches the end during
shooting, recording is automatically
commenced by the component for
backup purposes, which has been set to
the recording standby mode.
DV CMD SEL
(Camera)
For setting the recording operation to be
performed by the component for backup
purposes when the START/STOP button
on the camera recorder has been pressed.
REC_P:
The mode is switched between recording
and recording pause.
STOP:
The mode is switched between recording
and stop.
<Note>
Select STOP as the item’s setting if the
component for backup purposes is not
equipped with a recording pause function.
REC LAMP
(Camera)
For setting the lighting of the tally lamps.
OFF: The tally lamps do not light.
FRONT: The front tally lamp (by the
microphone) lights.
REAR: The rear tally lamp (by the
viewfinder) lights.
BOTH: Both the front and rear tally lamps
light.
The underlining indicates the factory setting.
48 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menus
OTHER FUNCTIONS screen
Item/
Description of settings
(display mode)
BEEP SOUND
(Camera)
For setting the beep tone to ON or OFF.
OFF
ON
When ON is selected as the setting, the
beep tone is sounded at the times given
below.
O When the beep tone is sounded, the
audio signals from the output connectors
are muted, and the beep tone is output
instead.
[Beep tone sounds once]
OWhen the POWER switch has been set
to ON
OWhen shooting has commenced
[Beep tone sounds twice]
OWhen shooting has been temporarily
stopped
[Beep tone sounds 10 times]
OWhen the cassette tape has not been
inserted
OWhen the cassette tape is in the
recording pause mode
OWhen condensation has formed inside
the camera recorder
OWhen a problem has occurred in the
camera recorder
CLOCK SET
(Camera)
(VCR)
For setting the internal calendar of the
camera recorder.
TIME SHIFT
(Camera)
(VCR)
For adding the time which was set using
this item to the time of the internal calendar
(to compensate for time differences) for
display in the viewfinder and on the LCD
monitor. The clock time after the
compensation is also recorded on the tape.
+23h --- +1h, OFF, –1h --- –23h
(In 1-hour increments)
TAPE PROTECT When the camera recorder is left on
(Camera)
standby for about 5 minutes in the shooting
pause mode, it is automatically set to the
tape protection mode. Which tape
protection mode is to be established is
selected using this item.
POWEROFF: The camera recorder’s power is
set to the OFF mode.
STBY: The cylinder head is set to the stop
mode.
USER FILE
(Camera)
(VCR)
LOAD: The settings stored last in the user
file are loaded.
SAVE: The user file settings which have
been changed are saved.
INITIAL: The user file settings are restored
to the factory settings.
O When the LOAD or INITIAL operation
has been performed, set the POWER
switch on the camera recorder to OFF
and then to ON again in order to enable
the settings.
HOUR METER
(Camera)
(VCR)
For indicating the total rotational time of the
cylinder head (5-digit display in 1-hour
increments).
The underlining indicates the factory setting.
49 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen displays
Camera mode and VCR mode
1
Marker
A
T C 1 2 : 3 4 : 5 6 : 0 0 Z 7 8
I – P A U S E
U S E R - 1
DV
O
S P
4
2 5 P
S Q U
MF 2 5
2222222 MA C R O
2 2222
5
2
2222
22
2
2
P 3.2 K
222222 22 2222222 F 5 . 6
2
2
6
1 8
dB
7
S P O T
1/ 1 2 3 . 4
L OW L I G H T
ND 1/ 64
A U G 3 1 2 0 0 3 2 3 : 5 9 : 5 9
ND 1/ 64
I N D E X
ALC
4 8 KCH1
CH2
22m i n
3
1Counter display
4Recording time mode display (SP or LP)
Each time the COUNTER button is pressed,
the data is selected in the sequence given
5Squeeze recording display
below.
COUNTER:
Counter value
M COUNTER:
Counter value in the memory stop mode
TC:
Time code value
This appears when SQUEEZE has been
selected (see page 41) as the ASPECT
CONV item setting on the setting menu
CAMERA SETUP screen and squeeze
recording is being performed or when
squeeze recorded images are being played
back.
“TC2” is displayed when the time code
value could not be read out properly from
the tape.
UB:
User’s bit value
6Setting selection display
The selected setting appears here when a
switch has been selected or a button has
been pressed to select a setting.
“UB2” is displayed when the user’s bit
value could not be read out properly from
the tape.
7Auto iris control status display
STD : Standard auto iris control
SPOT : Auto iris control for spotlight
BACK : Auto iris control for backlight
compensation
FR:
Information on the frame rate used when
shooting
FR 50I : Standard (50i interlace) mode
(50 fields per sec.)
Detect area
FR 25P : 25P progressive mode
(25 frames per sec.)
2AWB/ABB operation status display
The operation statuses of the auto white
balance and auto black balance are displayed
here.
Marker
3AWB error display
LOW LIGHT:
This appears when the luminance is too
low during the auto white balance
adjustment.
50 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen displays
=
;
A I – P A U S E
T C 1 2 : 3 4 : 5 6 : 0 0
U S E R - 1
Z 7 8
DV
O
S P
>
2 5 P
S Q U
MF 2 5
<
8
@
A
22222222222222 MA C R O
2222222222
22222222222222222 F 5 . 6
P 3.2 K
?
B
1 8
dB
S P O T
1/ 1 2 3 . 4
L OW L I G H T
ND 1/ 64
A U G 3 1 2 0 0 3 2 3 : 5 9 : 5 9
ND 1/ 64
I N D E X
ALC
4 8 KCH1
CH2
22m i n
:
9
8Shutter speed display
:
The shutter speed is normally displayed here.
“SLOW” is displayed in the slow shutter
mode.
This flashes when the cassette tape has
not been inserted or when it has been set
to the recording inhibit mode.
:
This lights if a problem occurs in the
camera recorder when face-to-face
shooting is performed in the mirror mode.
:
When the ZEBRA button is pressed and the
marker is displayed (see page 17), the video
level of the image near the center of the
screen is displayed as a value from 0% to
90%.
:
When the level exceeds 90%, “90% ” is
This lights when the internal battery used
for the calendar has run down.
displayed.
9Audio level meter display
>Zoom position display
The zoom position from Z00 (max. wide
–34 dB
–12 dB
0 dB
angle) to Z99 (max. telephoto) appears here.
CH1
CH2
?AWB information display
The white balance information appears here.
:Audio sampling frequency display
;Scene filename display
@Focus control information display
The focus control information from 99 to 00
appears here.
<Progressive display
The information on the frame rate when
shooting in the progressive mode is displayed
here.
95 (focal length: infinity)
:
50 (focal length: approx. 1 meter)
Under 49 (macro range)
:
00 (focal length: approx. 2 cm)
ODepending on the zoom position, the focus
may not be within the macro range.
Similarly, depending on the zoom position,
the lower limit of the macro range may
differ.
=Warning information displays
REMOTE:
This flashes when the component for which
the wireless remote control unit is set is the
wrong one.
:
This lights when condensation has formed
inside the camera recorder.
:
AMacro control display
This flashes when the cylinder head is
dirty.
BIris display
The F-number appears here.
51 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen displays
A I – P A U S E
T C 1 2 : 3 4 : 5 6 : 0 0
U S E R - 1
Z 7 8
J
DV
O
S P
I
2 5 P
S Q U
MF 2 5
22222222222222 MA C R O
2222222222
22222222222222222 F 5 . 6
P 3.2 K
1 8
dB
C
D
S P O T
1/ 1 2 3 . 4
L OW L I G H T
ND 1/ 64
A U G 3 1 2 0 0 3 2 3 : 5 9 : 5 9
ND 1/ 64
I N D E X
F
ALC
4 8 KCH1
CH2
22m i n
H
G
E
CGain display
HRemaining tape display
The gain value setting of the video amplifier
appears here.
Nothing appears here while the remaining
tape is being calculated.
The remaining tape amount is not displayed
when intermittent recording or slow-motion
playback has been performed.
DND filter display
The selected ND filter appears here.
“ND – –” appears on the display when the ND
FILTER switch has shifted out of position (to
a position other than OFF, 1/8 or 1/64).
Check the ND FILTER switch position.
ICamera shake compensation
display
This appears when ON has been selected as
the camera shake compensation function
setting.
ERecommended ND filter display
Displayed here is the ND filter which is
recommended under the current shooting
conditions.
JBackup component status displays
The status of the backup component
connected to the DV connector appears here.
It does not appear when OFF has been
selected as the setting for the DV CONTROL
item on the setting menu OTHER
FUNCTIONS screen.
FDate and time display
Month:
JAN (January), FEB (February), MAR (March), APR
(April), MAY (May), JUN (June), JUL (July), AUG
(August), SEP (September), OCT (October), NOV
(November), DEC (December)
DVO : Recording
DV
;
: Recording standby
: Status in which the backup
component cannot be controlled
: Backup component not connected
Day of the month
Year:
2002 --- 2089
DV
DV – –: The
backup
component
is
connected, but the recording or
recording standby mode has not
been established.
Hours: (24-hour clock)
Minutes
Seconds
mmm dd yyyy hh:mm:ss
GRemaining battery charge display
As the remaining battery charge diminishes,
the display changes in the following
sequence:
5
5
5
5
.
When the battery has run down completely,
(and then ) flashes.
(When the AC adapter is used, a display
other than may appear: this is normal
and not indicative of malfunctioning.)
52 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen displays
O
L
K
A I – P A U S E
T C 1 2 : 3 4 : 5 6 : 0 0
U S E R - 1
Z 7 8
DV
O
S P
2 5 P
S Q U
MF 2 5
22222222222222 MA C R O
2222222222
22222222222222222 F 5 . 6
P 3.2 K
1 8
dB
S P O T
1/ 1 2 3 . 4
L OW L I G H T
ND 1/ 64
A U G 3 1 2 0 0 3 2 3 : 5 9 : 5 9
ND 1/ 64
I N D E X
N
ALC
M
4 8 KCH1
CH2
22m i n
KOperation mode displays
NIndex recording display
REC
O
: Recording
: Recording (during face-to-face
shooting)
This lights when an index signal is recorded
during recording by pressing the USER
button to which the INDEX function has
already been allocated.
PAUSE : Recording standby
O
;
: Recording standby (during face-
to-face shooting)
: Playback pause
It flashes when the INDEX button is pressed
before recording (index signal recording
standby status).
;
STNDBY : Standby (cylinder head rotation
stopped)
: Audio dubbing recording standby
: Audio dubbing
OAUTO button operation display
“ A ” appears when the AUTO button has
been pressed and the function which was set
on the setting menu AUTO SW screen has
been activated.
A. DUB
A. DUB
1
;
1
: Playback
5
?1
(
6
) : Fast forward/cue (rewind/review)
: Slow playback (reverse slow
playback)
(2?)
CHK
: Rec check
9
(:
) : Search (reverse search)
;1
(2;) : Frame advance playback
(reverse
frame
advance
playback)
BLANK : Blank search
REC END : Rec end search
/a (a /a ):
a
1
5
2
6
Variable speed search (reverse variable
speed search)
LIntermittent recording display
This appears when ON or ONE-SHOT has
been selected as the setting for the
INTERVAL REC item on the setting menu
RECORDING SETUP screen.
MMic level automatic control display
This appears when ON has been selected as
the setting for the MIC ALC item on the
setting menu RECORDING SETUP screen.
53 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen displays
A I – P A U S E
T C 1 2 : 3 4 : 5 6 : 0 0
U S E R - 1
Z 7 8
DV
O
S P
22222222222222
2 5 P
S Q U
MF 2 5
22222222222222 MA C R O
22
Q
P
22 2222222222
P 3.2 K
22222222222222222 F 5 . 6
2222222222222
L OW L I G H T
ND 1/ 64
1 8
ND 1/ 64
I N D E X
dB
S P O T
1/ 1 2 3 . 4
ALC
A U G 3 1 2 0 0 3 2 3 : 5 9 : 5 9
22m i n
4 8 KCH1
CH2
V O L UME
–
?
?
?
?
?
?
– –
+
R
WARNING
PWarning displays
This appears when a problem has occurred in
the camera system.
UNPLAYABLE TAPE
(OTHER FORMAT)
FOCUS LOCK
The tape cannot be played back since it
(problem with focus operation)
has the wrong format.
PSD NG
COPY INHIBITED
(problem
compensation control)
with
camera
shake
Since the input signals are copy-guarded,
they cannot be recorded properly.
UNABLE TO A. DUB
QUSER button information display
(LP RECORDED)
The functions allocated to the USER buttons
are displayed here while the mode check
button is held down.
Since the tape was recorded in the LP
mode, audio dubbing cannot be performed.
INCOMPATIBLE TAPE
Since the tape has different specifications
(it may be a data storage tape, for
instance), it cannot be used.
EXTERNAL
DV DISCONNECT
This appears when EXT has been selected
as the setting for the DV CONTROL item
on the setting menu OTHER FUNCTIONS
screen, and shooting has been performed
without an external component connected
to the DV connector.
RMonitor volume level meter display
The volume level meter for output from the
built-in speaker and PHONES jack is
displayed here when the AUDIO MON/VAR
button is pressed.
AUTO OFF
This appears when a problem has occurred in
the tape transport system.
When this display appears, the camera
recorder’s power is automatically turned off.
CYLINDER LOCK
LOADING LOCK
UNLOADING LOCK
T REEL LOCK (take-up reel lock)
S REEL LOCK (supply reel lock)
54 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen displays
VCR mode
1 7
S
1
S
T
T C 1 2 : 3 4 : 5 6 : 0 0
S P
S Q U
F 5 . 6
1 8 dB
U
V
22222222222222
2222222222
22222222222222222
22222222222222222
A U G 3 1 2 0 0 3 2 3 : 5 9 : 5 9
22m i n
4 8 KCH1
CH2
SSearch number display
The index number used to perform the index
search appears here. (S1 to S9)
TCamera shake compensation
display
When ON has been selected as the setting
for the CAMERA DATA item on the setting
menu DISPLAY SETUP screen,
is
displayed also during tape playback for the
camera data when images were shot in the
camera shake compensation mode.
UIris display
When ON has been selected as the setting
for the CAMERA DATA item on the setting
menu DISPLAY SETUP screen, the F-
number during shooting is displayed also
during tape playback as the camera data.
VGain display
When ON has been selected as the setting
for the CAMERA DATA item on the setting
menu DISPLAY SETUP screen, the gain
value during shooting is displayed also during
tape playback as the camera data.
55 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen displays
Selecting the display
The items listed below which appear in the viewfinder and on the LCD monitor are displayed by the
setting selected for the OTHER DISPLAY item (see page 47) of the setting menu DISPLAY SETUP
screen.
OTHER DISPLAY item setting
Display item
MODE CHK button
ALL
PARTIAL
==
OFF
1 Counter display
≤
≤
==
==
(Camera)
≤ (VCR)
k
4 Recording time mode display (SP or LP)
≤
k
5 Squeeze recording display
7 Auto iris control status display
8 Shutter speed display
≤
≤
≤
≤
≤
≤
k
≤
k
k
≤
≤
k
==
9 Audio level meter display
==
==
(Camera)
≤ (VCR)
k
: Audio sampling frequency display
≤
≤
k
k
; Scene filename display
< Progressive display
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
≤
k
k
==
k
==
> Zoom position display
==
≤
? AWB information display
@ Focus control information display
B Iris display
≤
==
≤
k
==
==
≤
k
k
k
C Gain display
≤
k
D ND filter display
≤
k
≤
E Recommended ND filter display
F Date and time display
≤
k
==
==
==
==
≤
==
==
==
≤
G Remaining battery charge display
H Remaining tape display
I Camera shake compensation display
M Mic level automatic control display
O AUTO button operation display
Q USER button information display
==
==
k
k
k
k
≤
k
≤
≤
k
k
≤
: Displayed
k : Not displayed
== : Displayed by another setting
56 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting external components
OBefore recording signals from an external
component, check that the video signals are
input.
Inputting to and outputting from
analog components
OWhen signals from an external component
are being recorded, do not stop the signal
output at the external component side or
disconnect any of the cables. It may not be
possible for the component to be recognized
when recording is resumed.
OIf video signals have been input to both the S-
VIDEO IN/OUT connector and VIDEO IN/OUT
connector, the signals of the S-VIDEO IN/OUT
connector take precedence.
OIt is not possible to record the audio signals if
video signals are not input to the S-VIDEO
IN/OUT connector or VIDEO IN/OUT
connector except when performing audio
dubbing.
OWhen images containing copy-guarded
signals (signals that protect copyrights) are
recorded using this unit, they will appear as
mosaic patterns when they are played back.
$ When an external component is to be
connected and its video and audio signals
are to be input to the camera recorder,
connect the camera recorder to the output
connectors on the external component.
$ Conversely, when an external component is
to be connected and the video and audio
signals of the camera recorder are to be
input to the component, connect the camera
recorder to the input connectors on the
external component.
$
When signals from an external component
are to be recorded, set the unit to the VCR
mode and operate the VCR REC button to
initiate recording.
O The functions provided for the input
connectors and the ones provided for the
output
connectors
are
switched
automatically.
VCR REC
CH 1 SELECT CH 2 SELECT
INT(L)
INPUT 1
INPUT 2
INT(R)
INPUT 2
INPUT 1
INPUT 2
$ When connecting an audio component, set
the INPUT1 switch or INPUT2 switch to the
LINE position.
The input level is 0 dBu; the recording level
is adjusted using the AUDIO controls.
$ When connecting an external microphone,
set the INPUT1 switch or INPUT2 switch to
the MIC position.
OSet the input level (–50 dBu and –60
dBu) using the MIC GAIN 1 and MIC
GAIN 2 items on the setting menu
RECORDING SETUP screen.
OWhen mounting an external microphone
on the microphone shoe of the camera
recorder, use the accessory microphone
holder and microphone holder adapter.
OTo supply the signals from an external
microphone to CH1 and CH2, connect the
external microphone to the INPUT2 jack,
and set both the CH1 SELECT and CH2
SELECT switches to the INPUT2 position.
(See page 15)
Microphone
holder
Microphone
holder adapter
12 mm
(XSB4+12FZ)
6 mm
(XSB4+6FZ)
57 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting external components
OBefore recording signals from an external
component, check that the video signals are
input.
Inputting to and outputting from
digital components
OWhen signals from an external component
are being recorded, do not stop the signal
output at the external component side or
disconnect any of the cables. It may not be
possible for the component to be recognized
when recording is resumed.
OWhen an IEEE 1394 cable has been
connected to the DV connector, do not apply
a strong load from outside. Doing so may
damage the connector.
OWhen signals are recorded using this unit,
audio signals will be recorded in the same
mode as the one which was set for the
playback tape regardless of the menu setting.
OWhen signals are recorded using this unit, the
bottom part of the images being monitored
(the images which are seen on an LCD
monitor, viewfinder or TV set) may be
distorted or they may shake vertically: this is
normal and not indicative of malfunctioning.
The images actually recorded are free of this
distortion and shaking.
$
A digital video component equipped with a
DV connector can be connected for
digitally recording and playing back video
and audio signals as well as time codes,
etc.
When signals from an external component
are to be recorded, set the unit to the VCR
mode and operate the VCR REC button to
initiate recording.
$
O The functions provided for the input
connectors and the ones provided for the
output
connectors
are
switched
automatically.
VCR REC
OWhen images containing copy-guarded
signals (signals that protect copyrights) are
recorded using this unit, they will appear as
mosaic patterns when they are played back.
OIt may not be possible to input or output
digital signals to or from some components
even if the component concerned is equipped
with a DV connector. For details, refer to the
operating instructions of the component to be
connected.
58 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Shooting
Preparation and inspections
Regular shooting
Set the camera recorder’s POWER switch to
ON, and switch between shooting and shooting
pause using the START/STOP button.
Before shooting, check that the camera recorder
is operating properly. Also check that the
equipment is set up in a way that is suited to the
shooting conditions.
When shooting from
START/STOP button on the handle can be used
to initiate shooting.
a
low angle, the
$ Batteries
START/STOP button
Have a fully charged battery ready. It is also
recommended that a spare battery be kept on
hand as well.
$ Cassette tapes
Check that the cassette tapes available can
be recorded on.
OCheck that they have not been set to the
accidental erasure prevention status.
OCheck that they do not contain valuable
video recordings.
OCheck that the cassette holder is closed
properly.
$ Viewfinder
Check that the diopter adjustment has been
performed for the viewfinder.
REC check
When the REC CHECK button is pressed in the
shooting pause mode, the picture and sound 2
seconds before the shooting was suspended
are played back, and the shooting pause mode
is then established again at the original position
on the tape.
OIf recording has not been performed for 1 or
more seconds, the rec check function cannot
be used.
$ Zoom, focus and iris
OCheck whether the motor-driven zoom
operations and manual zoom operations
can be performed.
OCheck whether the auto focus and manual
focus operations can be performed.
OCheck whether the auto iris and manual iris
operations can be performed.
OBear in mind that when a backup component
has been connected and used to record
backup images, the rec check images will be
recorded.
$ Time data
OCheck whether the calendar and time are
correct.
OCheck whether the time code and user’s bit
have been set correctly.
REC CHECK button
$ External components
OCheck whether the external components
connected are operating properly.
OCheck whether the external components
have been connected properly.
59 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Shooting
Face-to-face shooting
Index recording
When the LCD monitor is opened and rotated
180 degrees toward the lens, and the person
operating the camera recorder records images
of himself or herself, the impression of the shot
images may appear to be different from usual.
If MIRROR is selected as the setting for the
SELFSHOOT item on the setting menu
DISPLAY SETUP screen, a left-right reversed
image appears on the LCD monitor, and the
person operating the camera recorder can shoot
images of himself or herself that appear as if he
or she is looking at himself or herself in the
mirror.
(When the INDEX function has been allocated
to one of the USER buttons)
When the INDEX button is pressed during
shooting or recording, the index signal is
recorded on the tape.
When it is pressed while shooting or recording
is temporarily stopped, the index signal is set to
the recording standby status.
When the
shooting or recording is then resumed, the index
signal is recorded on the tape at that time.
Searches (index searches) can be performed
during playback once the index signals have
been recorded.
However, even when shooting images in the
mirror mode, the recorded images will be the
same as ones which have been shot regularly
as the images are not recorded as a mirror
reflection.
When shooting in the mirror mode, the
information which appears in the viewfinder and
on the LCD monitor is limited to the following
items:
Using the USER buttons
One of 11 functions can be allocated in turn to
each of the USER1, USER2 and USER3
buttons.
In accordance with the subject concerned, the
shooting conditions can be instantly selected or
fade effects can be added to the images.
For details, refer to the USER1 and USER2
items (page 42) on the setting menu SW MODE
screen.
O
O
: Shooting
;
: Shooting pause
: Remaining battery charge display
: Warning display
Intermittent recording
When
appears, return the LCD monitor to
There are two intermittent recording modes: the
mode in which images are shot at fixed
intervals, and the frame-by-frame shooting
mode.
its original position, and check the message
of the warning display.
1 Set the shooting mode for intermittent
recording using the INTERVAL REC item on
the setting menu RECORDING SETUP
screen. (See page 46)
2 Set the recording time using the REC TIME
item.
3 Set the standby time using the INTERVAL
TIME item.
4 When the START/STOP button is pressed,
recording starts in the shooting mode for
intermittent recording.
5 When the OPERATION lever is tilted in the
“$” direction, “I –” blinks, and intermittent
recording is set to the temporary stop status.
OWhile intermittent recording is in progress,
no other operations are accepted.
OWhile intermittent recording is in progress,
the remaining tape amount is not
displayed.
Even when the intermittent recording mode has
been set, it will be returned to OFF when the
power is turned off.
60 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Shooting
Backup recording
Bear in mind the following points when
performing backup recording.
OThe menu item settings remain stored in
the memory even after the power has been
The camera images of the camera recorder can
be recorded and their recording can be backed
up automatically on the external component
connected to the DV connector.
turned off.
Therefore, if the camera
OSet the external component control method
using the DV CONTROL item and DV CMD
SEL item on the setting menu OTHER
FUNCTIONS screen. (See page 48)
recorder is used while the settings for
backup recording are still in place, the
images may be overwritten on the tape in
the connected component.
Upon completion of the backup recording,
check the menu item settings before
operating the camera recorder.
OIf another model AG-DVX100A is to be
used as the external component which will
perform the backup recording, select OFF
as the setting for the DV CONTROL item of
the external component, and set the
camera recorder to the VCR mode for use.
OWhen backup recording is to be performed,
operation may not proceed properly if two
or more external components are
connected.
OEnsure that the IEEE 1394 cable used for
the connection is not more than 4.5 meters
long.
OBefore proceeding with backup recording,
establish the status in which the DV signals
can be recorded by the external
component.
OWhen the tape in the camera recorder is
approaching the end during shooting while
backup recording is being performed with
“CHAIN” selected as the setting for the DV
CONTROL item (page 48), recording is
automatically started by the back-up
component which has been set to the
recording standby mode.
61 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Shooting
Progressive shooting
Bear in mind the following points when
shooting in any of the progressive modes.
OThe gain cannot be set to18 dB.
OWhen the progressive mode has been
selected, the sync signals of the images are
temporarily disturbed.
The progressive mode can be selected using
the PROGRESSIVE item (see page 42) of the
setting menu SCENE FILE screen.
25P mode:
Images are shot in the progressive mode at
25 frames per second.
The 25 frames per second images are
converted into 50-field interlace signals, and
the resulting video signals are output or
recorded.
OA shutter speed setting of 1/50 (OFF) is
recommended.
Shift-free, high-quality still pictures can be
obtained in this mode.
25 P
A B C D E F G H I J
AoAeBoBeCoCeDoDeEoEe Fo FeGoGeHoHe Io Ie Jo Je
50 i
62 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Normal playback
Variable speed search
Set the POWER switch to ON, and press the
CAMERA/VCR button to switch to the VCR
mode.
This function changes the playback speed to
locate scenes.
OWhen the OPERATION lever is tilted in the 1
direction during tape playback, the variable
search mode is established, “1a” appears in
the viewfinder and on the LCD monitor, and
the tape is played back at the 1a speed. No
sound is played back at this time.
Normal playback operations can be performed
using the OPERATION lever or accessory
wireless remote control unit.
OPERATION lever
OThe playback speed changes when the
AUDIO MON/VAR button is pressed. Each
time the button is pressed, the playback
speed changes by one setting in the following
sequence: 1/5a (or 1/3a in the LP mode),
1a, 2a, 5a, 10a and 20a.
OThe speed is varied in the forward direction
using the “+” button; conversely it is varied in
the reverse direction using the “–” button.
OWhen the remote control is used, pressing
the VAR.SEARCH button establishes the
variable speed search mode, and the
playback direction and playback speed are
changed using the “V” and “B” buttons
among the SET buttons.
3
MENU
1
6
;
5
∫
4
PUSH-SET
Tape protection mode
When the camera recorder remains in the
playback pause or recording pause mode for
more than 5 minutes, it is automatically set to
the stop mode in order to protect the tape.
However, if it remains in the playback pause
mode when the temperature is low, the stop
mode may be established sooner.
OTo return to normal playback, tilt the
OPERATION lever in the 1 direction.
Index search
This function is used to search the index signals
recorded on the tape. An index search can be
performed using the accessory wireless remote
control unit.
Tape blank search
ODuring tape playback, press the INDEX
button (9 or :) on the wireless remote
control unit.
“S1” appears in the viewfinder and on the
LCD monitor, and the search for the next
scene is started.
By pressing the EVF DTL/END SEARCH button
in the VCR mode, it is possible to search for
unrecorded parts on the tape or the part which
was shot last. For details, refer to the section
on the EVF DTL/END SEARCH button (page
10).
OTo stop the search at any time, press the
STOP ($) button.
EVF DTL/END SEARCH button
OEach time the INDEX button is pressed after
the search operation has commenced, “S2”
“S3” are displayed, and the second or any
subsequent scene can be searched. When a
scene is located, playback commences from
that part of the tape. (Any scene up to the
ninth in the reverse or forward direction from
the present position of the tape can be
specified.)
The index search function may not operate
smoothly if any of the intervals between one
index and the next are less than one minute.
63 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Condensation
How to tell when condensation has formed
inside and what to do about it
If, after the camera recorder’s power has been
3After two or three hours have elapsed,
turn on the power, and check whether the
condensation display has gone off.
Even if the condensation display has gone
off, wait another hour to be on the safe side
before attempting to operate the camera
recorder.
turned on, the
condensation display symbol
flashes, it means that condensation has formed
inside the camera recorder. If this happens, the
power will be automatically turned off after
several seconds.
Take the following action.
Bear in mind that condensation may be
forming before the condensation display
comes on.
1Remove the cassette.
No other functions will work. Depending on
the degree of condensation, it may not be
possible to eject the cassette, either. In this
case, wait two or three hours, and then try
ejecting the cassette.
OCondensation forms gradually so that the
condensation display may not appear for the
first 10 to 15 minutes after it has started to
form inside.
OIn very cold climates, condensation may
freeze and turn into frost. In this case, it will
take two or three hours for the frost to melt
and become condensation again.
2Wait two or three hours with the cassette
holder open.
The wait time differs depending on the
degree of condensation and the ambient
temperature.
Video heads
If the video heads are dirty, mosaic-type noise
may occur in some areas or the whole image
may turn blue when playing back a tape.
If the dirt accumulates, the recording capability
will deteriorate, and in the end it will not be
possible to record.
5If the images are not clear, repeat steps 1
to 4.
(Do not run the cleaning tape continuously
more than 4 times.)
ODo not rewind the cleaning tape at any
interim point. At the end of the tape, rewind
it, and use it again from the start.
OIf the heads are still dirty even after cleaning,
it may mean that the tape itself has
deteriorated so stop using it immediately.
OOveruse of the cleaning tape causes head
wear. If the heads are worn, clear pictures
will not be played back even immediately
after the heads have been cleaned.
Causes of dirty heads
OHigh concentrations of dust in the
atmosphere
OEnvironments which are very hot and very
humid
OTape damage
OProlonged operation
Using the cleaning cassette tape
1Insert the cleaning tape in the camera
recorder, and set the POWER switch to
ON.
OIf the cleanliness of the heads is not improved
by the cleaning tape, the camera recorder
must be cleaned and/or repaired by your local
dealer. Consult with your dealer.
2Press the CAMERA/VCR button, and
Regular inspections
check that the VCR lamp has lit.
In order to view clean and clear images, it is
recommended that the video heads and other
worn parts be replaced after they have been
used for about 1,000 hours. (This period will
vary significantly depending on the temperature,
humidity, dust and other conditions in the
operating environment.)
3Tilt the OPERATION lever in the
direction, and allow 10 seconds to pass
before tilting it in the $ direction.
1
(Do not rewind the tape at this point.)
4Remove the cleaning tape, proceed with a
test recording and playback using another
tape, and check the images.
64 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Q&A)
Power supply-related problems
Q1: No power.
A1: Has the battery or AC adapter been
Battery-related problems
Q1: The battery runs down quickly.
A1-1: Has the battery been adequately
charged? Charge it until the CHARGE
lamp of the AC adapter has gone off.
(See page 20)
connected correctly?
Check the
connections. (See page 21)
Q2: The power goes off on its own.
A2: The power will automatically go off if
shooting is temporarily stopped for more
than 5 minutes in order to prevent the
battery from running down and keep the
tape from wearing.
A1-2: Is the camera recorder being used in cold
place?
The battery is easily affected by the
ambient temperature. Its operating time is
reduced in cold locations.
A1-3: Has the battery reached the end of its
service life?
Check the setting selected for the TAPE
PROTECT item on the setting menu
OTHER FUNCTIONS screen. (See page
49)
The service life of the battery differs
depending on how it is used. If it works
only for a short time even after it has
adequately charged, it means that the
battery has reached the end of its service
life.
Q3: The power is turned on but it goes off
immediately.
A3-1: Has the battery run down?
If the remaining battery charge display
Q2: The battery cannot be charged.
A2: Is the DC cable connected to the AC
adapter? The battery cannot be charged
if this cable is connected.
flashes or the
display has
appeared, it means that the battery has
run down.
Recharge the battery or insert an
adequately charged battery. (See page
20)
Problems during normal video
recording
A3-2: Has condensation formed?
When the camera recorder has been
carried into a warm room from a cold
place, condensation may form inside. If
this happens, the power is automatically
turned off, and ejecting the cassette is the
only operation which can be performed.
Wait until the condensation has dried up.
(See page 64)
Q1: Recording is not possible even though
the cassette tape has been inserted
properly.
A1-1: Has the accidental erasure prevention
knob on the cassette tape been set to
“SAVE?” If it has, recording cannot be
performed. (See page 22)
A1-2: Has the cassette tape reached the end?
Replace it with a new one.
A1-3: Is the POWER switch at the ON position?
A1-4: Is the VCR lamp lit?
Shooting is not possible in the VCR mode.
A1-5: Is the cassette holder open?
If the cassette holder is open, it is not
possible to perform any VCR operations.
A1-6: Has condensation formed?
If condensation has formed, ejecting the
cassette tape is the only operation which
can be performed.
Wait until the
condensation dries up. (See page 64)
A1-7: If AUTO OFF/T REEL LOCK appears on
the display, the tape may have snapped.
Check the tape.
65 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Q&A)
Problems during various kinds of
Display-related problems
Q1: Something is wrong with the time code
display.
video recording
Q1: No automatic focusing
A1: When the reverse slow playback mode is
set, the count shown on the time code
display becomes inconsistent; however,
this is normal and not indicative of
malfunctioning.
A1-1: Has the manual focus mode been set?
The focus is adjusted automatically in the
auto focus mode. (See page 11)
A1-2: Is a scene which is hard to bring into
focus in the auto focus mode being shot?
Some scenes are hard to bring into focus
using auto focus. In cases like this, use
the manual focus mode instead for
focusing.
Q2: The remaining tape display does not
match the actual amount of tape
remaining.
A2-1: The remaining tape is not displayed
accurately with continuous shooting
sessions lasting less than 30 seconds.
A2-2: A display which is two to three minutes
less than the actual tape remaining time
sometimes appears.
Scenes hard to bring into focus
OShooting both distant and close-up
subjects
OShooting subjects through dirty window
panes
OShooting subjects in dark locations
OShooting while objects that glitter or
dazzle are around the subject
OShooting fast-moving subjects
OShooting subjects with minimal contrast
Playback-related problems
(video)
Q1: No playback, even when the play
button is pressed.
Editing-related problems
Q1: No audio dubbing.
A1-1: Has the accidental erasure prevention
knob on the cassette tape been set to
“SAVE?” If it has, recording cannot be
performed. (See page 22)
A1: Has the CAMERA/VCR button been
pressed and has the VCR lamp lit?
If the VCR lamp is not lit, playback-related
operations cannot be performed. (See
page 10)
A1-2: Has an attempt been made to edit parts
shot in the LP mode? Audio dubbing
cannot be performed as the track width on
the tape is narrower than the head width
in the LP mode.
Q2: Mosaic-type noise is generated during
cue and review.
A2: This is a phenomenon inherent to digital
video. It is not indicative of malfunctioning.
Q3: No playback images are seen even
though the camera recorder is
connected with the TV set correctly.
A3: Is the TV set’s input selector at “video
input?” Read through the operating
instructions of the TV set, and select the
video input connector to which the camera
recorder has been connected.
Q4: The playback images are not displayed
clearly.
A4: Are the camera recorder’s heads dirty?
If they are dirty, the playback images will
not be displayed clearly.
66 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Q&A)
Playback-related problems
Other types of problems
Q1: The cassette tape cannot be ejected.
A1: Is power being supplied?
(audio)
Q1: No playback sound is heard from the
camera recorder’s speaker.
Has the AC adapter been plugged in or
the battery inserted properly?
When the power is supplied, the cassette
can be ejected without setting the
POWER switch to ON.
A1: Has the camera recorder’s volume level
been set too low?
In the VCR mode, press the AUDIO
MON/VAR button “+” to increase the
volume. (See page 14)
Q2: Ejecting the cassette tape is the only
operation which can be performed.
A2-1: Has any condensation formed?
Q2: More than one recorded stream of
sound is heard.
A2: Has MIX been selected as the setting for
the 32K (12-bit) AUDIO item on the
setting menu PLAYBACK FUNCTIONS
screen? (See page 44)
If condensation forms, ejecting the
cassette tape is the only operation which
can be performed.
Wait until the
condensation dries up. (See page 64)
A2-2: When the cassette holder is closed
immediately after opening (by sliding the
EJECT switch), operations other than
eject may not be possible.
If audio dubbing editing is performed on a
tape recorded with 32K (12-bit) selected
as the setting for the AUDIO REC item on
the setting menu RECORDING SETUP
screen, the sound heard during the
recording and the sound recorded later
will be heard together. It is also possible
to listen to each stream of sound
separately. (See page 44
If this does happen, slide the EJECT
switch to open the cassette holder once
again, then close the holder after ensuring
that the cassette mechanism has
completed the eject operation.
Q3: The remote control unit does not work.
A3-1: Has the battery in the remote control unit
run down?
Q3: When audio dubbing is performed, the
original sound is erased.
A3: When audio dubbing is performed for a
part which was shot with 48K (16-bit)
selected as the setting for the AUDIO
REC item on the setting menu
RECORDING SETUP screen, the original
sound will be erased. Use the 32K (12-
bit) setting during shooting. (See page
44)
If the remote control unit fails to operate
even when it is operated near the remote
control sensor of the camera recorder, it
means that the button battery has run
down.
Replace it with a new one. (See page 19)
A3-2: Do the remote control settings match
properly?
If the [REMOTE] settings of the remote
control unit and camera recorder do not
match, the remote control unit will not
work even when it is operated. (See page
19)
Q4: A rattling sound is heard when the
camera recorder is tilted toward the
front or back.
A4: When the VCR mode is established or the
power switch is at OFF, a rattling sound
may be heard from the camera unit due to
its structure. This is not indicative of
malfunctioning.
67 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Do not use benzine or paint thinners to clean
the camera recorder.
Viewfinder maintenance
When dust has collected inside the viewfinder,
take off the eye cup holder, and remove the
dust.
OThe inside of the eye cup holder has a
special coating: for this reason, it must not be
wiped under any circumstances. When dust
has collected, use an air blower or similar
device to blow off the dust.
OPoint the viewfinder slightly upward, then
remove the eye cup holder by turning it
counterclockwise.
OTo attach the eye cup holder, turn it clockwise
with the index mark on the eye cup holder
face up.
OUse of benzine or paint thinners may cause
the camera recorder body to become
deformed or the surface coating to peel off.
OWhen cleaning or otherwise maintaining the
camera recorder, either remove its battery or
disconnect its AC cable from the power outlet.
OUse a soft, clean cloth to wipe the camera
recorder. To remove stubborn stains, dilute
some kitchen detergent, dip a cloth into the
solution and use it to wipe off the dirt, and then
remove any remaining moisture with a dry
cloth.
Index mark
Eye cup holder
OWhen the eye cup holder is to be removed,
it will be easier to turn it if it is removed with
the eye cup still mounted.
OBefore attaching the eye cup holder,
remove the eye cup to reveal the index
mark.
68 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Pick-up device
Interline transfer 1/3-inch CCD image senser
[GENERAL]
(a3)
Supply voltage:
Number of pixels
DC 7.2 V (Battery)
Total number of pixels: 470,000,
Number of effective pixels: 440,000
(pixel offset system)
Lens
Leica DICOMAR optical image stabilizer lens,
motorized/manual mode switching, 10a zoom
F1.6 (f = 4.5 to 45 mm)
(35 mm equivalent: 32.5 to 325 mm)
Optical system
DC 7.9 V (AC adapter)
Power consumption:
6.8 W (when viewfinder is used)
7.8 W (when LCD monitor is used)
9.2 W (max.)
indicates safety information.
Ambient operating temperature
0°C to +40°C
Prism system
ND filters
Ambient operating humidity
10% to 85% (no condensation)
Weight
1.69 kg (excluding battery and accessories)
Dimensions (WaHaD)
139a160a364 mm
Recording format
Digital video SD format
Tape format
Mini DV
Recorded video signals
625i (PAL)
In the progressive mode, the signals are
converted into the 625i system and recorded.
Shooting mode
1/8, 1/64
Gain
0, +3, +6, +9, +12, +18 dB (50i mode)
0, +3, +6, +9, +12 dB (progressive mode)
(Fixed at 0 dB in the slow shutter mode)
Shutter speeds
Preset
50i mode:
1/50 (OFF), 1/60, 1/120, 1/250, 1/500,
1/1000, 1/2000 sec.
25P mode:
1/25, 1/50 (OFF), 1/60, 1/120, 1/250,
1/500, 1/1000 sec.
Synchro scan
50i mode:
1/50.2 to 1/248.0 sec.
25P mode:
1/25.1 to 1/248.0 sec.
Slow shutter
50i (625i)
Progressive mode (25P)
Recorded audio signals
PCM digital recording
16 bits: 48 kHz/2 channels
12 bits: 32 kHz/4 channels
Recording tracks
Digital video, audio signals:
helical track
Time code:
helical track (sub-code area)
Tape speed
50i mode:
1/3, 1/6, 1/12, 1/25 sec.
25P mode:
1/3, 1/6, 1/12 sec.
Minimum subject illuminance
3 lux (F1.6, 18 dB gain, 50 % video output)
Lens hood
Large-sized lens hood with wide angle of
SP mode: 18.831 mm/sec.
LP mode: 12.568 mm/sec.
Recording time (when AY-DVM60 is used)
SP mode: 60 minutes
LP mode: 90 minutes
Tape used
6.35 mm wide metal tape
FF/REW time
Approx. 85 sec. (when AY-DVM60 is used)
view
Filter diameter
72 mm
LCD monitor
3.5-inch LCD colour monitor, 200,000 pixels
Viewfinder
0.44-inch LCD colour viewfinder, 180,000
pixels
Internal microphone
Stereo microphone
Internal speaker
20 mm diameter
69 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
[VIDEO]
[AC ADAPTER]
Sampling frequency
Y: 13.5 MHz, PB/PR: 6.75 MHz
Quantizing
Input:
100 – 240 V AC, 50/60 Hz, 20 W
Output:
Video camera: DC 7.9 V, 1.4 A (max.)
Charge: DC 8.4 V, 1.2 A
8 bits
Video compression system
DCT + variable length code
Error correction
indicates safety information.
Reed-Solomon product code
Weight
0.16 kg
Dimensions (WaHaD)
70a44.5a116 mm
[AUDIO]
Sampling frequency
48 kHz/32 kHz
Quantizing
16 bits/12 bits
[OPTIONAL ACCESSORIES]
Frequency response
20 Hz to 20 kHz
Wow & flutter
Wide conversion lens
AG-LW7208G
16:9 conversion lens
AG-LA7200G
Below measurable limits
XLR microphone
AG-MC100G
Hard carrying case
AG-HT100G
Soft carrying case
AG-SC100G
[CONNECTORS]
VIDEO IN/OUT (input/output automatically
switched)
Pin jack, analogue composite input/output,
1.0 V [p-p], 75 Ω
S-VIDEO IN/OUT (input/output automatically
switched)
S-connector, Y/C separate signal
input/output, Y: 1.0 V [p-p], C: 0.3 V [p-p],
75 Ω
Battery
CGR-D16S (1600 mAh)
CGP-D28S (2800 mAh)
CGA-D54S (5400 mAh: product equivalent to
battery supplied)
AC adapter kit
AUDIO IN/OUT (input/output automatically
switched)
Pin jacks a2 (CH1, CH2)
Input: 316 mV, high impedance
Output: 316 mV, 600 Ω
DV
AG-B15E (product equivalent to AC cable,
DC cable and AC adapter supplied)
Cleaning tape
AY-DVMCLC
4-pin, digital input/output, IEEE 1394
standard complied with
INPUT 1, INPUT 2
XLR (3 pins) a2 (CH1, CH2)
LINE/MIC switching, high impedance
LINE: 0 dBu
MIC : –50 dBu/–60 dBu (menu selection)
DC INPUT
7.9 V
PHONES
Stereo (3.5 mm diameter)
CAM REMOTE
Mini jack (2.5 mm diameter)
Weight and dimensions shown are approximate.
Specifications are subject to change without
notice.
70 (E)
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
Download from Www.Somanuals.com. All Manuals Search And Download.
Matsushita Electric Industrial Co., Ltd.
Printed in Japan
F0903T1103 @
Download from Www.Somanuals.com. All Manuals Search And Download.
E
|