TG5831_5832AL.book Page 1 Monday, March 14, 2005 4:28 PM
Operating Instructions
5.8 GHz Digital Cordless Answering System
Model No.
KX-TG5831AL
5.8 GHz Digital Cordless Answering System
with Dual Handsets
Model No.
KX-TG5832AL
Model shown is KX-TG5831AL.
This unit is compatible with Caller ID. To use this feature, you must
subscribe to the appropriate service offered by your service provider.
Charge the battery for 6 hours before initial use.
Please read these Operating Instructions before using the unit and save
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 3 Monday, March 14, 2005 4:28 PM
Table of Contents
Listening to messages . . . . . . . . . . . . . 43
Listening to messages using the base
unit . . . . . . . . . . . . . . . . . . . . . . . . . 43
Listening to messages using the
handset . . . . . . . . . . . . . . . . . . . . . . 44
Memory capacity . . . . . . . . . . . . . . . . . 45
Remote operation. . . . . . . . . . . . . . . . . 46
Using the answering system
remotely . . . . . . . . . . . . . . . . . . . . . 46
Answering system settings. . . . . . . . . . 47
Remote code . . . . . . . . . . . . . . . . . 47
Ring count . . . . . . . . . . . . . . . . . . . . 48
Caller’s recording time . . . . . . . . . . . 49
Message alert . . . . . . . . . . . . . . . . . 49
Useful Information
Wall mounting. . . . . . . . . . . . . . . . . . . . 50
Base unit . . . . . . . . . . . . . . . . . . . . . 50
Charger (KX-TG5832AL only) . . . . . 53
Belt clip. . . . . . . . . . . . . . . . . . . . . . . . . 54
Headset (optional) . . . . . . . . . . . . . . . . 54
Error messages . . . . . . . . . . . . . . . . . . 55
Troubleshooting . . . . . . . . . . . . . . . . . . 56
General use . . . . . . . . . . . . . . . . . . 56
Programmable settings . . . . . . . . . . 56
Making/answering calls, Intercom . . 57
Phonebook . . . . . . . . . . . . . . . . . . . 58
Caller ID . . . . . . . . . . . . . . . . . . . . . 58
Answering system . . . . . . . . . . . . . . 59
Battery charge . . . . . . . . . . . . . . . . 59
Power failure . . . . . . . . . . . . . . . . . . 60
Instructions to customer . . . . . . . . . . . . 61
Technical information . . . . . . . . . . . . . . 63
Base unit . . . . . . . . . . . . . . . . . . . . . 63
Handset . . . . . . . . . . . . . . . . . . . . . 63
Charger (KX-TG5832AL only) . . . . . 63
Index
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . 64
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 4 Monday, March 14, 2005 4:28 PM
Introduction
Thank you for purchasing a Panasonic cordless telephone.
We recommend keeping a record of the following information for future reference.
Serial No.
Date of purchase
(found on the bottom of the unit)
Name and address of dealer
Attach your purchase receipt here.
Your phone
KX-TG5831AL
KX-TG5832AL
L References in these operating instructions to the charger and to the other handset are
for KX-TG5832AL users only.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 5 Monday, March 14, 2005 4:28 PM
Introduction
Accessory information
Included accessories
Quantity
KX-TG5831AL KX-TG5832AL
No. Accessory items
1
2
3
4
5
6
7
8
AC adaptor for base unit
Telephone line cord
Telephone plug
Wall mounting adaptor
Battery
1
1
1
1
1
1
1
–
–
1
1
1
1
2
2
2
1
1
Handset cover
Belt clip
Charger
AC adaptor for charger
1
5
2
3
7
4
8
6
Additional/replacement accessories
Accessory items
Order number
Rechargeable nickel metal HHR-P104
hydride (Ni-MH) battery
Headset
KX-TCA88AL
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 6 Monday, March 14, 2005 4:28 PM
Introduction
Incorrect reassembly can cause
electric shock when the unit is
subsequently used.
Important safety
instructions
12. Unplug this unit from power outlets and
refer servicing to an authorised service
centre when the following conditions
occur:
When using this unit, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock, or
personal injury.
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on this unit.
3. Unplug this unit from power outlets
before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for
cleaning.
4. Do not use this unit near water, for
example near a bathtub, wash bowl,
kitchen sink, etc.
A. When the power cord is damaged
or frayed.
B. If liquid has been spilled into the
unit.
C. If the unit has been exposed to rain
or water.
D. If the unit does not work normally
by following the operating
instructions. Adjust only controls
covered by the operating
instructions. Improper adjustment
may require extensive work by an
authorised service centre.
5. Place the unit securely on a stable
surface. Serious damage and/or injury
may result if the unit falls.
E. If the unit has been dropped or
physically damaged.
6. Do not cover slots and openings on the
unit. They are provided for ventilation
and protection against overheating.
Never place the unit near radiators, or
in a place where proper ventilation is
not provided.
7. Use only the power source marked on
the unit. If you are not sure of the type
of power supplied to your home,
consult your dealer or local power
company.
F. If the unit exhibits a distinct change
in performance.
13. During thunderstorms, avoid using
telephones except cordless types.
There may be a remote risk of an
electric shock from lightning.
14. Do not use this unit to report a gas
leak, when in the vicinity of the leak.
SAVE THESE
INSTRUCTIONS
8. Do not place objects on the power
cord. Install the unit where no one can
step or trip on the cord.
9. Do not overload power outlets and
extension cords. This can result in the
risk of fire or electric shock.
10. Never push any objects through slots
in this unit. This may result in the risk of
fire or electric shock. Never spill any
liquid on the unit.
CAUTION:
Installation
L Never install telephone wiring during a
lightning storm.
L Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
L Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the
network interface.
11. To reduce the risk of electric shock, do
not disassemble this unit. Take the unit
to an authorised service centre when
service is required. Opening or
removing covers may expose you to
dangerous voltages or other risks.
L Use caution when installing or modifying
telephone lines.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 7 Monday, March 14, 2005 4:28 PM
Introduction
L Do not touch the plug with wet hands.
the unit in health care facilities if any
regulations posted in the area instruct
you not to do so. Hospitals or health care
facilities may be using equipment that
could be sensitive to external RF (radio
frequency) energy.
L The AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is installed near the unit and is
easily accessible.
Battery
To reduce the risk of fire or injury to
persons, read and follow these
instructions.
Notice
L Please ensure that a separate
telephone, not dependent on local
power, is available for emergency use.
L Use only the battery(ies) specified.
L Do not dispose of the battery(ies) in a
fire. They may explode. Check with local
waste management codes for special
disposal instructions.
L This equipment will be inoperable when
mains power fails.
L When a failure occurs which results in
the internal parts becoming accessible,
disconnect the power supply cord
immediately and return this unit to an
authorised service centre.
L Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and
may cause burns or injury to the eyes or
skin. The electrolyte may be toxic if
swallowed.
L To minimise the possibility of lightning
damage, when you know that a
thunderstorm is coming, we recommend
that you:
– Unplug the telephone line cord from
the phone jack.
L Exercise care when handling the
battery(ies). Do not allow conductive
materials such as rings, bracelets or
keys to touch the battery(ies), otherwise
a short circuit may cause the battery(ies)
and/or the conductive material to
overheat and cause burns.
– Unplug the power supply cord from
the AC power outlet.
L No “000” or other calls can be made
from this device during a mains power
failure.
L Charge the battery(ies) provided with or
identified for use with this product only in
accordance with the instructions and
limitations specified in this manual.
L The earcap on the handset is
magnetised and may retain metallic
objects.
WARNING:
L To prevent the risk of fire or electrical
shock, do not expose this product to rain
or any type of moisture.
L This equipment has been tested and
found to comply with AS/NZS 3548:
1995 limits for electromagnetic
interference. Any modifications to any
part of the system or to any peripherals
may void the EMC compliance of the
system or the peripherals.
Medical
L Consult the manufacturer of any
personal medical devices, such as
pacemakers or hearing aids, to
determine if they are adequately
shielded from external RF (radio
frequency) energy. (The unit operates in
the frequency range of 5.76 GHz to 5.84
GHz, and the power output level can
range from 0.25 to 0.5 watts.) Do not use
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 8 Monday, March 14, 2005 4:28 PM
Introduction
following places: Near obstacles such as
hills, tunnels, undergrounds, near metal
objects such as wire fences, etc.
For best performance
L Operating near 5.8 GHz electrical
appliances may cause interference.
Move away from the electrical
appliances.
Base unit location/noise
The base unit and handset use radio
waves to communicate with each other.
For maximum distance and noise-free
operation, we recommend the following:
Routine care
L Placing the unit away from electrical
appliances such as a TV, personal
computer or another cordless phone.
L Wipe the outer surface of the unit with a
soft cloth. Do not use benzine, thinner or
any abrasive powder.
L Placing the base unit in a HIGH and
CENTRAL location with no obstructions
such as walls.
L Raising the antennas vertically.
L If you use the handset near a microwave
oven which is being used, noise may be
heard. Move away from the microwave
oven and closer to the base unit.
L If you use the handset near another
cordless phone’s base unit, noise may
be heard. Move away from the other
cordless phone’s base unit and closer to
your base unit.
Environment
L Keep the unit away from electrical noise
generating devices, such as fluorescent
lamps and motors.
L The unit should be kept free from
excessive smoke, dust, high
temperature and vibration.
L The unit should not be exposed to direct
sunlight.
L Do not place heavy objects on top of the
unit.
L When you leave the unit unused for a
long period of time, unplug this unit from
power outlet.
L The unit should be kept away from heat
sources such as heaters, kitchen stoves,
etc. It should not be placed in rooms
where the temperature is less than 5 °C
or greater than 40 °C. Damp basements
should also be avoided.
L The maximum calling distance may be
shortened when the unit is used in the
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 9 Monday, March 14, 2005 4:28 PM
Preparation
Connections
Base unit
Fasten the AC adaptor cord.
Raise the antennas.
Hook
To power outlet (230–240 V AC, 50/60 Hz)
AC adaptor
To socket
Telephone line cord
Charger (KX-TG5832AL only)
To power outlet (230–240 V AC, 50/60 Hz)
AC adaptor
Note:
L Base unit: Use only the included Panasonic AC adaptor PQLV1AL.
L Charger: Use only the included Panasonic AC adaptor KX-TCA1AL.
L The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel
warm during use.)
L The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet.
Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the
adaptor may cause it to become disconnected.
L The unit will not work during a power failure. We recommend connecting a standard
telephone to the same telephone line or to the same telephone jack using a telephone
double adaptor.
L The unit is not designed to be used with rotary (pulse dialling) services.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 10 Monday, March 14, 2005 4:28 PM
Preparation
If you subscribe to an ADSL service
Battery installation
L Please attach a noise filter (contact your
ADSL provider) to the telephone line
between the base unit and the telephone
line jack in the event of the following:
– Noise is heard during conversations.
– Caller ID features (page 25) do not
function properly.
1 Insert the battery (1), and press it
down until it snaps into the
compartment (2).
2
1
To socket
2 Close the handset cover.
Telephone line cord
Noise filter
(For ADSL users)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 11 Monday, March 14, 2005 4:28 PM
Preparation
Battery strength
You can confirm the battery strength on the
handset display.
Battery charge
Place the handset on the base unit or
charger for 6 hours before initial use.
Battery icon
5
Battery strength
Fully charged
Medium
L The unit will beep once, the CHARGE
indicator will light, and “Charging” will
be displayed.
6
7
Low
L “Charge completed” is displayed
when the battery has been fully charged.
The CHARGE indicator will remain lit.
When flashing: needs
to be recharged.
8
Discharged
Base unit
Recharging the battery
Recharge the battery when:
– “Recharge battery” is displayed or
OR
7 flashes on the handset display.
– the handset beeps intermittently while it
is in use.
Note:
L Recharge the handset battery for more
than 15 minutes, or the display will
continue showing the indication.
L If the battery has been discharged, the
handset will display “Charge for 6h”
and 8 when you place the handset
on the base unit or charger.
CHARGE indicator
Charger (KX-TG5832AL only)
CHARGE
indicator
Note:
L To ensure the battery charges properly,
clean the charge contacts of the
handset, base unit, and charger with a
soft, dry cloth once a month. Clean more
often if the unit is subject to grease, dust,
or high humidity.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 12 Monday, March 14, 2005 4:28 PM
Preparation
Battery performance
Battery replacement
After your Panasonic battery is fully
charged, you can expect approximately
the following performance:
If battery performance diminishes, make
sure you have cleaned the charge
contacts and fully charged the battery. The
battery needs to be replaced if any of the
following are displayed after a few phone
calls even when you have fully charged the
battery.
Operation
Operating time
While in use
(talking)
Up to 5 hours
While not in use
Up to 11 days
Up to 3 hours
*1
(standby)
– “Recharge battery”
– 7 (flashing)
– “Charge for 6h”
– 8
While using the
Clarity Booster
feature (page 20)
*1 Handset is off the base unit or charger
but not in use.
L Use only the rechargeable Panasonic
battery noted on page 5.
Note:
1 Press the notch on the cover firmly and
slide it as indicated by the arrow.
L Battery power is consumed whenever
the handset is off the base unit or
charger, even when the handset is not in
use. The longer you leave the handset
off the base unit or charger, the shorter
you can actually talk on the handset.
Actual battery performance depends on
a combination of how often the handset
is in use and how often it is not in use.
L Once the battery is fully charged, you do
not have to charge it again until
“Recharge battery” is displayed or
7 flashes. This will maximise the
battery life.
2 Replace the old battery with a new one,
and close the cover (see page 10 for
battery installation).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 13 Monday, March 14, 2005 4:28 PM
Preparation
Controls and displays
Controls
Base unit
A
B
C
D
E
F
G H I
J
K
E
KX-TG5832AL KX-TG5831AL
L
M
N
O P Q R
A {LOCATOR/INTERCOM 1}
B {LOCATOR/INTERCOM 2}
C {LOCATOR/INTERCOM}
D CHARGE indicator
E Antenna
K {ERASE}
L Charge contacts
M MIC (Microphone)
N VOL. (Volume) {<} {>}
O {STOP}
F Speaker
P {MESSAGE}
MESSAGE indicator
G Display
Q {<} (Repeat)
H {ANSWER ON}
ANSWER ON indicator
R {>} (Skip)
I {GREETING REC} (Recording)
J {GREETING CHECK}
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 14 Monday, March 14, 2005 4:28 PM
Preparation
Handset
Charger (KX-TG5832AL only)
A
H
I
A
B
J
B
K
L
M
C
D
B
A Charge contacts
E
F
B CHARGE indicator
Using the navigator key
The handset navigator key can be used to
navigate through menus and to select
items shown on the display, by pressing
{^}, {V}, {<}, or {>}.
N
O
P
G
A Speaker
B Soft key
C Headset jack
D {C} (TALK)
E Navigator key
F {s} (SP-PHONE)
G {PAUSE} {REDIAL}
H Ringer indicator
Message indicator
I Receiver
J Display
K {MENU}
L {OFF}
M {MUTE} {CLEAR}
N {HOLD} {INTERCOM}
O Microphone
P Charge contacts
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 15 Monday, March 14, 2005 4:28 PM
Preparation
Soft keys
The handset features 2 soft keys. By
Display
pressing a soft key, you can select the
function displayed directly above it.
Base unit display items
Displayed
Meaning
item
L The functions displayed will vary
depending on how you are using the
unit.
E
Flashes when message
L When a function does not appear above
a soft key, the soft key has no function.
memory is full.
E
Flashes when the date and
time need to be set.
5
C
Base unit is on an intercom
call, or handset is using the
answering system.
Rcvd
calls
Phone
book
K
L
When flashing: base unit is
paging or is being paged.
B
C
Line is in use.
When flashing: a call is on
hold or the answering
system is answering a call.
When flashing rapidly: a
call is being received.
Soft key examples:
Display
Action
function
Rcvd
calls
Enters caller list
E
Greeting message
recording error
Conf
Establishes a conference
call
9@
Answering system is in
greeting only mode (caller
messages will not be
recorded).
*1
*1 KX-TG5832AL only
H1
Handsetnumber;displayed
when paging or being
Backlit display and handset keypad
The handset display and dialling buttons
will light for a few seconds after pressing
any of the handset’s controls or lifting the
handset off the base unit or charger. They
will also light when a call is being received.
paged. (example shown
*1
here: handset 1)
*1 KX-TG5832AL only
Handset display items
Displayed
Meaning
item
J
5
Voice enhancer is on.
Battery strength
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 16 Monday, March 14, 2005 4:28 PM
Preparation
7 Press {OFF}.
Setting the date and time
Note:
L If you make a mistake when entering the
date and time, press {<}, {>}, {V}, or
{^} to move the cursor, then make the
correction.
Set the date and time so that the unit will
announce the day and time each message
was recorded by the answering system
(page 41) when you play back messages.
L If a power failure occurs, E will flash to
indicate the date and time must be set
again.
1 Press {MENU}.
2 Scroll to “Date and time” by pressing
{V} or {^}, then press {>} or {Select}.
To confirm the date and time
Repeat steps 1 and 2. Press {OFF} when
finished.
Date and time
KBack dB SelectL
Time adjustment (Caller ID subscribers
only)
When calls are received, Caller ID will
automatically adjust the date and time
(including daylight saving time).
3 Enter the current day, month, and year
by selecting 2 digits for each.
Example: 15 June, 2005
Press {1}{5} {0}{6} {0}{5}.
Date:31.12.2005
Time:12:00 AM
L If you have not set the date and time
manually, Caller ID will not adjust the
date and time.
KAM/PM
SaveL
L You can turn this feature off (page 38).
4 Enter the current hour and minute (12-
hour clock format) by selecting 2 digits
for each.
Example: 9:30 PM
Press {0}{9} {3}{0}.
Date:15.06.2005
Time:12:00 AM
K
AM/PM
Save
L
L
5 Select “AM” or “PM” by pressing {AM/
PM}.
Date:15.06.2005
Time:09:30 AM
KAM/PM
Save
6 Press {Save}.
L When the date and time are set, E
disappears from the base unit
display.
L If the handset beeps 3 times, the date
and time were not set correctly. Enter
the correct digits.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 17 Monday, March 14, 2005 4:28 PM
Making/Answering Calls
4 When finished talking, press {OFF} or
place the handset on the base unit or
charger.
Making calls
Note:
L Talk alternately with the caller in a quiet
room.
L If the other party has difficulty hearing
you, press {V} to decrease the speaker
volume.
Soft keys
{OFF}
L While on a call, you can switch from the
receiver to the speakerphone by
pressing {s}. To switch back to the
receiver, press {C}.
{C}
{s}
Navigator key
{MUTE}
{CLEAR}
{HOLD}
To adjust the speaker volume
6 levels (high to low) are available.
While using the speaker, press {V} or {^}
repeatedly.
{PAUSE}
{REDIAL}
Microphone
1 Lift the handset and press {C}.
L “Talk” will be displayed.
To dial after confirming the entered
number
2 Dial the phone number.
1 Enter the phone number.
3 When finished talking, press {OFF} or
place the handset on the base unit or
charger.
Example:
3334444
KRecall
CallL
Note:
L To correct a digit, press {<} or {>} to
move the cursor, then press
{CLEAR}. Enter the correct number.
L “Line in use” is displayed when
someone is talking on the other handset
(KX-TG5832AL only) or another phone.
L If a pause is required when dialling,
press {PAUSE} where needed (page
20).
To adjust the receiver volume
3 levels (high/medium/low) are available.
While using the receiver, press {V} or {^}
repeatedly.
L To cancel, press {OFF}.
2 Press {C}, {s}, or {Call}.
To use the speakerphone
3 When finished talking, press {OFF} or
place the handset on the base unit or
charger.
1 Lift the handset and press {s}.
L “SP-phone” will be displayed.
To redial the last number dialled
1 Press {C} or {s}.
2 Dial the phone number.
3 When the other party answers, speak
into the microphone.
2 Press {REDIAL}.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 18 Monday, March 14, 2005 4:28 PM
Making/Answering Calls
To make a call using the redial list
The last 5 phone numbers dialled are
stored in the redial list.
Answering calls
When a call is being received, the ringer
indicator flashes rapidly.
1 Press {REDIAL}.
L The last number dialled will be
1 Lift the handset and press {C} or {s}.
displayed.
L You can also answer a call by
pressing any button except {V}, {^},
{<}, {>}, or {OFF}. (Any key talk
feature)
2 Press {V} or {^} repeatedly to display
the desired number.
L To delete the displayed number,
press {CLEAR}.
L To exit the list, press {OFF}.
2 When finished talking, press {OFF} or
place the handset on the base unit or
charger.
3 Press {C}, {s}, or {Call}.
Auto talk
This feature allows you to answer a call by
simply lifting the handset off the base unit
or charger. You do not need to press {C}.
To activate this feature, see page 35.
Temporary ringer off
While the handset is ringing for an outside
call, you can turn the ringer off temporarily
by pressing {OFF}. The handset will ring
the next time a call is received.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 19 Monday, March 14, 2005 4:28 PM
Making/Answering Calls
MUTE button
Useful features during a
call
You can mute your voice during a
conversation. While mute is turned on you
will be able to hear the other party, but the
other party will not be able to hear you.
To mute your voice, press {MUTE}.
HOLD button
This feature allows you to put an outside
call on hold.
Example:
Talk
00-00-30 <Mute>
KX-TG5831AL:
Press {HOLD} during an outside call.
L “Hold” will be displayed.
L To return to the call, press {C} or {s}.
L “<Mute>” will flash on the display.
L To return to the conversation, press
{MUTE}, {C}, or {s}.
Voice enhancer
KX-TG5832AL:
This feature can simulate a band signal
above the normal bandwidth limitations,
achieving a sound which is close to the
actual voice. You can turn this feature on
or off, depending on the circumstance.
1 Press {HOLD} during an outside call.
L To transfer the call to the other
handset, see page 31, step 2.
2 Press {HOLD} again.
1 Press {MENU} during an outside call.
L “Hold” will be displayed.
L To return to the call, press {C} or
{s}.
L The other handset user can take the
call by pressing {C} or {s}.
2 To turn this feature on or off, press {3}.
L You can also select “V.E. on” or
“V.E. off” by pressing {V} or {^}
then pressing {>}.
Note:
g3=V.E. on
L “Line on hold” will be displayed on
the other handset (KX-TG5832AL only).
L When turned on, “J” will be
displayed.
L If another phone is connected on the
same line (page 9), you can also take
the call by lifting its handset.
Note:
L If a call is kept on hold for more than 6
minutes, an alarm tone will start to
sound and the ringer indicator will flash
rapidly. After 4 additional minutes on
hold, the call will be disconnected.
L Once you turn voice enhancer on, it will
be activated for all outside calls until
turned off.
L You can also turn this feature on or off by
programming (page 35).
L Depending on the condition and quality
of your telephone line, this feature may
emphasise existing line noise. If it
becomes difficult to hear, turn this
feature off.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 20 Monday, March 14, 2005 4:28 PM
Making/Answering Calls
Clarity booster
PAUSE button (for PBX/long
This feature can improve sound clarity
when the handset is used in an area where
there may be interference. During an
outside call, this feature will be turned on
automatically when necessary. This
feature will turn off when you hang up or
put a call on hold. It will not turn off
automatically during a call. You can also
turn this feature on or off manually.
distance service users)
A pause is sometimes required when
making calls using a PBX or long distance
service.
For example, if you need to dial the line
access number “9” when making outside
calls with a PBX:
1 Press {9}.
1 Press {MENU} during an outside call.
2 Press {PAUSE}, then dial the phone
number.
2 Press {2} to select “Booster on” or
Example:
“Booster off”.
9P0555666777
L You can also select “Booster on” or
“Booster off” by pressing {V} or
{^} then pressing {>}.
K
Recall
CallL
3 Press {C}, {s}, or {Call}.
1=Phonebook
2=Booster on
g
Note:
L A 3.5 second pause is inserted each
time {PAUSE} is pressed. Press
repeatedly to insert longer pauses.
L While this feature is turned on,
“BOOST” will flash on the display.
Note:
Recall button
Pressing {Recall} allows you to use
special features of your host PBX such as
transferring an extension call, or accessing
optional telephone services such as Call
Waiting.
L If this feature is turned off manually
during a call, it will not be turned on
automatically during the same call.
L While this feature is turned on, battery
operating time will be shortened (page
12).
Example:
Talk
00-00-20
Recall
Call share (KX-TG5832AL only)
K
When the other handset is on an outside
call, this feature allows you to join that call.
To join a conversation, press {C} or {s}
when the other handset is on an outside
call.
Note:
L To change the recall time, see page 36.
L “Conference” will be displayed.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 21 Monday, March 14, 2005 4:28 PM
Phonebook
7 Press {Save}.
L To add other items, repeat from step
2.
Using the phonebook
The handset phonebook allows you to
make calls without having to dial manually.
You can add 50 names and phone
numbers to the handset phonebook and
search for phonebook entries by name.
8 Press {OFF}.
Note:
L Caller ID subscribers can use ringer ID
and light-up ID features (page 25).
Adding items to the phonebook
To store emergency numbers
Emergency numbers are numbers stored
in the phonebook that can be dialled using
the phonebook even when dial lock is
turned on (page 37).
1 Press {Phonebook}.
Rcvd
calls
Phone
book
K
L
To store a number as an emergency
number, add # at the beginning of the
name (see “Adding items to the
phonebook”).
2 Press {Add}.
L The display shows the number of
items in the phonebook.
Example:
Phonebook
7 items
SearchL
Character table
The dial keys can be used to enter
characters. To enter a character, press the
appropriate dial key, repeatedly if
necessary. To enter another character that
is located on the same dial key, first press
{>} to move the cursor to the next space.
K
Add
3 Enter the name (max. 16 characters).
See the character table for entry.
Enter name
|
Back
K
NextL
Key
{1}
{2}
{3}
{4}
{5}
{6}
{7}
{8}
{9}
{0}
{*}
{#}
Characters
& ’
(
)
,
–
.
/
1
4 Press {Next}.
a
d
g
j
b
c
f
A B C 2
D E F 3
5 Enter the phone number (max. 32
e
h
k
digits).
i
G H I
K L
4
5
L If a pause is required when dialling,
press {PAUSE} where needed (page
20).
l
J
m n
o
r
M N O 6
P Q R S 7
T U V 8
W X Y Z 9
Enter phone no.
p
t
q
u
s
v
y
w x
z
6 Press {Next}.
0
Space
L If you want to change the name and
number, press {Edit}, then repeat
from step 3.
;
#
Example:
Tom
0555654321
Edit
{CLEAR} To delete a character or
number
K
SaveL
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 22 Monday, March 14, 2005 4:28 PM
Phonebook
L If there is no item corresponding to
the letter you selected, the next item
will be displayed.
To edit/correct a mistake
Press {<} or {>} to move the cursor to the
character or number you wish to erase,
then press {CLEAR}. Enter the
3 Press {V} repeatedly to display the
appropriate character or number.
desired item.
L To exit the phonebook, press {OFF}.
L To dial the displayed number, press
{C} or {s}.
Note:
L Press and hold {CLEAR} to erase all
characters or numbers.
Editing items in the phonebook
Calling someone in the
phonebook
Phonebook items can be searched for
alphabetically by scrolling through the
phonebook items.
1 Press {Phonebook}, then press
{Search}.
2 Press {V} or {^} repeatedly to display
the desired item.
1 Press {Phonebook}.
3 Press {Edit}.
L For quick search, you can skip to step
3.
4 Edit the name if necessary. See the
character table on page 21 for
character entry.
2 Press {Search}.
0-9=Name search
dB=Scroll list
5 Press {Next}.
6 Edit the phone number if necessary.
3 Press {V} or {^} repeatedly to display
the desired item.
7 Press {Next}, then press {Save}.
L To exit the phonebook, press {OFF}.
4 Press {C} or {s}.
Note:
L To edit other items, repeat from step
2.
8 Press {OFF}.
L To view a phone number over 16 digits
long, follow steps 1 to 3, then press
{Edit} and {Next}. Press {OFF} when
finished.
Erasing items in the phonebook
1 Press {Phonebook}, then press
{Search}.
To search for a name by initial
2 Press {V} or {^} repeatedly to display
the desired item.
1 Press {Phonebook}, then press
3 Press {CLEAR}.
{Search}.
4 Press {Yes}.
2 Press the dialling button ({0} to {9},
{#}, or {*}) which corresponds to the
first letter you are searching for (see the
character table, page 21).
L To cancel erasing, press {No}.
L To erase other items, repeat from
step 2.
Example: “LISA”
Press {5} repeatedly to display any
name with the initial “L”.
5 Press {OFF}.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 23 Monday, March 14, 2005 4:28 PM
Phonebook
Chain dial feature
Copying phonebook
items (KX-TG5832AL
only)
This feature allows you to dial phone
numbers from the phonebook while you
are on a call.
Example: Using a long distance calling
card
You can copy one or all of the phonebook
items of one handset to the phonebook of
the other handset.
1 Dial from the phonebook:
18000123456 (Calling card access
number).
Important:
2 When prompted, dial from the
phonebook:
L Make sure the destination handset is not
in use.
1234 (Calling card PIN).
L Do not place your handset on the base
unit or charger until copying has
finished, otherwise copying will stop.
3 When prompted, dial from the
phonebook:
15550123456 (the person you want to
call).
L If an outside call is received during the
phonebook copy, copying will stop. You
will need to copy the item(s) later.
1 During an outside call, press
{MENU}.
L Ringer ID and light-up ID settings for
phonebook items are not copied (page
25).
2 Press {1} to select “Phonebook”.
3 Press {V} or {^} repeatedly to display
the desired item.
Copying an item
4 Press {Call}.
1 Press {MENU}.
L Repeat from step 1 to dial other
numbers.
2 Scroll to “Copy phonebook” by
pressing {V} or {^}, then press {>}.
Note:
3 Scroll to “Copy 1 item” by pressing
L When storing a calling card access
number and your PIN in the phonebook
as one phonebook item, press {PAUSE}
to add pauses after the number and PIN
as necessary (page 20).
{V} or {^}, then press {>}.
4 Press {V} or {^} repeatedly to display
the desired item.
L To search for the item by initial, see
page 22.
5 Press {Send}.
L When the item has been copied,
“Complete” will be displayed.
L The destination handset display will
show “Phonebook Receiving”,
then “Phonebook Received”.
L To copy another item, repeat from
step 4.
6 Press {OFF}.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 24 Monday, March 14, 2005 4:28 PM
Phonebook
Copying all items
1 Press {MENU}.
2 Scroll to “Copy phonebook” by
pressing {V} or {^}, then press {>}.
3 Scroll to “Copy all items” by
pressing {V} or {^}, then press {>}.
L When all items have been copied,
“Complete” will be displayed.
L The destination handset display will
show “Phonebook Receiving”,
then “Phonebook Received”.
4 Press {OFF}.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 25 Monday, March 14, 2005 4:28 PM
Caller ID Service
Call waiting and Caller ID
compatible
If you subscribe to Caller ID service, your
handset displays the 2nd caller’s
information while talking. After you hear a
call waiting tone, the caller’s phone
number will be displayed.
Using Caller ID service
This unit is Caller ID compatible. To use
Caller ID features, you must subscribe to
your telephone company’s Caller ID
service.
Caller ID features
You can answer the 2nd call, keeping the
1st call on hold.
Follow Telstra or your service provider
instructions using {Recall}.
When an outside call is being received, the
calling party’s phone number will be
displayed.
Phone numbers for the last 50 different
callers will be logged in the caller list,
allowing you to return missed calls. Caller
information is stored by the most recent
call to the oldest.
L If the phone number is stored in the
phonebook with its name, the caller’s
name will also be displayed.
L Please contact Telstra or your service
provider for details and availability in
your area.
L When Caller ID information is received
and it matches a phone number stored
in the phonebook:
For Caller ID Type II users
– The stored name will be displayed and
logged in the caller list. (Private name
display)
– The handset will use the ringer tone
and the ringer indicator colour you
assigned to the caller. (Ringer ID and
light-up ID)
When you receive a 2nd call during a
conversation, you will hear a signal tone
following the call waiting tone and the
conversation will be interrupted or
muted for a short period of time. This is
not fault of the product as these events are
normal.
L While listening to a message recorded
by the answering system, using the
handset, you can call back the caller
without having to dial the phone number
(page 45).
L The tones are generated by the
telephone company.
Ringer ID and light-up ID
This feature can help you identify who is
calling by using different ringers and ringer
indicator colours for different callers stored
in the phonebook. You can assign a
different ringer and indicator colour to each
phonebook item. When a call is received
from a caller stored in the phonebook, the
ringer and indicator colour are used after
Caller ID information is displayed.
L If the unit cannot receive caller
information, the following will be
displayed:
“Out of area”: The caller dialled from
an area which does not provide Caller ID
service.
“Private caller”: The caller
requested not to send caller information.
L If the unit is connected to a PBX system,
caller information may not be received
properly. Consult your PBX supplier.
L The ringer and indicator colour may be
changed after the 2nd ring.
L If the name display service is available in
your area, the display will show callers’
names. For further information, please
contact your telephone company.
Ringer ID
You can assign a different ringer tone to
each caller in the phonebook. If you select
“No Ringer ID”, the unit will use the
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 26 Monday, March 14, 2005 4:28 PM
Caller ID Service
ringer tone you set on page 34 when a call
is received from that caller. The default
setting is “No Ringer ID”.
Caller list
Caller information for the last 50 different
callers will be logged in the caller list. You
can use this list to return missed calls.
1 Press {Phonebook}, then press
{Search}.
L Caller information includes phone
numbers, the date and time of calls, and
the number of times the caller called.
2 Press {V} or {^} repeatedly to display
the desired item.
3 Press {Option}.
Missed calls
4 Press {1} to select “Ringer ID”.
If a call is not answered, the unit treats the
call as a missed call. The number of
missed calls is shown on the handset
display. This lets you know if you should
view the caller list to see who called while
you were out.
5 Press {V} or {^} repeatedly to select
the desired ringer tone.
L You can also select the ringer tone by
pressing {1} to {7}, or {0} (“No
Ringer ID”).
Example: Handset off the base unit or
charger
6 Press {Save}, then press {OFF}.
10 missed calls
Rcvd
calls
Light-up ID
Phone
book
K
L
You can assign a different ringer indicator
colour to each caller in the phonebook.
Select “Color1-Default” (Amber),
“Color2” (Green), “Color3” (Red), or
“Multicolor”.
Note:
L When the unit has new messages, “New
message” will be displayed in place of
“missed calls”.
1 Press {Phonebook}, then press
{Search}.
Viewing the caller list and
calling back
2 Press {V} or {^} repeatedly to display
the desired item.
1 Press {V} or {^} to enter the caller list.
3 Press {Option}.
2 Press {V} to search from the most
recent call, or press {^} to search from
the oldest call.
4 Press {2} to select “Light-up ID”.
5 Press {V} or {^} repeatedly to select
L To exit the caller list, press {OFF}.
3 Press {C} or {s}.
Note:
the desired ringer indicator colour.
L You can also select the colour by
pressing {1} to {4}.
6 Press {Save}, then press {OFF}.
L You can also press {Rcvd calls} to
enter the caller list.
L Calling back will not be possible if the
caller information does not include a
phone number.
L In some cases, you may have to edit the
number before dialling.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 27 Monday, March 14, 2005 4:28 PM
Caller ID Service
L If the caller’s name and phone number
Editing a caller’s phone number
before calling back
are stored in the phonebook, the caller’s
name and phone number are displayed
alternately.
You can edit a phone number in the caller
list.
Example:
JACK SMITH
3:10P 29JUN.
1 Press {V} or {^} to enter the caller list.
2 Press {V} or {^} repeatedly to display
0555333444
3:10P 29JUN.
the desired item.
3 Press {Edit}.
L If an arrow (→ ) is displayed after the
number, the whole phone number will
not be shown. Press {*} to see the
remaining numbers or to return to the
previous display. Each time you press
{*}, the display will change alternately.
4 Add or erase digits to the beginning of
the number as necessary.
L To add a digit, press the desired dial
key.
L To erase a digit, press {CLEAR} or
{#}.
Example:
222333344445555
3:10P 29JUN.
→
{*}
5 Press {C} or {s} to call back.
2223333444455556
666
Note:
L The edited phone number will not be
saved in the caller list.
L KX-TG5832AL only:
Each handset has its own caller list. If
you viewed the caller list or answered a
call on one handset, the same
information in the other handset will be
displayed as “missed calls”.
Storing caller information into
the phonebook
Items in the caller list can be stored into
each handset’s phonebook.
Displayed symbols
1 Press {V} or {^} to enter the caller list.
L If the same caller calls more than once, it
will be displayed with the number (“×2”
to “×9”). Only the date and time of the
most recent call will be stored.
2 Press {V} or {^} repeatedly to display
the desired item.
L To edit the number, press {Edit}, then
edit the number (see “Editing a
caller’s phone number before calling
back”, step 4).
L A Q is displayed next to items which
have already been viewed or answered
on this handset.
3 Press {Save}.
L “Enter name” will be displayed.
L If the caller has name information, the
name and phone number will be
saved. Skip to step 6.
4 Enter the name if necessary (see page
21, step 3).
5 Press {Next}, then press {Save}.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 28 Monday, March 14, 2005 4:28 PM
Caller ID Service
L To continue storing other items,
repeat from step 2.
Erasing caller information
6 Press {OFF}.
Erasing a selected item
Note:
1 Press {V} or {^} to enter the caller list.
L If the caller information does not include
a phone number, you cannot store it in
the phonebook.
2 Press {V} or {^} repeatedly to display
the desired item.
3 Press {CLEAR}.
L To erase other items, repeat from
step 2.
L To exit the caller list, press {OFF}.
Erasing all items
Make sure that you have no missed calls.
1 Press {V} or {^} to enter the caller list.
2 Press {All erase}.
L To cancel erasing, press {No}.
3 Press {Yes}.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 29 Monday, March 14, 2005 4:28 PM
Intercom Features
From the base unit to the handset
Intercom
1 Base unit:
Intercom calls can be made between a
handset and the base unit (and between 2
handsets, KX-TG5832AL only).
Press {LOCATOR/INTERCOM}.
L The handset will beep for 1 minute.
L To stop paging, press {LOCATOR/
INTERCOM}.
Note:
L If you have difficulty hearing the other
party while using the speaker, decrease
the speaker volume.
2 Handset:
Press {C}, {s}, or {INTERCOM} to
answer the page.
L If you receive a phone call while talking
on the intercom, you will hear 2 tones
(page 34). To answer the call, press
{OFF}, then press {C} or {s}.
3 Base unit:
When the paged party answers, speak
into the MIC.
L You cannot change the ringer tone for
intercom calls.
4 Base unit:
When finished talking, press
{LOCATOR/INTERCOM}.
For KX-TG5831AL users
Note:
L You can locate a misplaced handset by
paging it. (Handset locator)
From the handset to the base unit
1 Handset:
Press {INTERCOM}.
L The base unit will beep for 1 minute.
L To stop paging, press {OFF}.
2 Base unit:
Press {LOCATOR/INTERCOM} to
answer the page.
3 Handset:
When finished talking, press {OFF}.
Note:
L During an intercom call, the handset
user can switch to the speaker by
pressing {s}. To switch back to the
receiver, press {C}.
L To adjust the base unit’s speaker
volume, press {>} or {<} repeatedly. 8
levels (high to low) are available.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 30 Monday, March 14, 2005 4:28 PM
Intercom Features
From the base unit to a handset
For KX-TG5832AL users
Call the desired unit by selecting the
extension number, shown in the upper
right of each handset’s display. The base
unit’s extension number is 0.
1 Base unit:
Press {LOCATOR/INTERCOM 1} or
{LOCATOR/INTERCOM 2}.
L The handset will beep for 1 minute.
L To confirm the handset’s extension
number ([1]or [2]), place the handset
on the base unit or charger.
L To stop paging, press either
{LOCATOR/INTERCOM 1} or
{LOCATOR/INTERCOM 2}.
L The base unit will display the paging or
paged handset number (H1 or H2).
2 Handset:
Press {C}, {s}, or {INTERCOM} to
answer the page.
From the handset to the base unit
1 Handset:
3 Base unit:
Press {INTERCOM}, then press {0}.
When the paged party answers, speak
into the MIC.
L You can also select the base unit by
pressing {V} or {^} then pressing
{>}.
L The base unit will ring for 1 minute.
L To stop paging, press {OFF}.
4 Base unit:
When finished talking, press either
{LOCATOR/INTERCOM 1} or
{LOCATOR/INTERCOM 2}.
2 Base unit:
Note:
Press either {LOCATOR/INTERCOM
1} or {LOCATOR/INTERCOM 2} to
answer the page.
L You can locate a misplaced handset by
paging it. (Handset locator)
From one handset to the other handset
Example: When handset 1 calls handset 2.
3 Handset:
When finished talking, press {OFF} or
place the handset on the charger.
1 Handset 1:
Press {INTERCOM}, then press the
other handset number {2}.
Note:
L During an intercom call, the handset
user can switch to the speaker by
pressing {s}. To switch back to the
receiver, press {C}.
L You can also select the handset by
pressing {V} or {^} then pressing
{>}.
L The paged handset will beep for 1
minute.
L To adjust the base unit’s speaker
volume, press {>} or {<} repeatedly. 8
levels (high to low) are available.
L To stop paging, press {OFF}.
2 Handset 2:
Press {C}, {s}, or {INTERCOM} to
answer.
3 When finished talking, press {OFF} or
place the handset on the base unit or
charger.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 31 Monday, March 14, 2005 4:28 PM
Intercom Features
Transferring a call (KX-
TG5832AL only)
Conference calls (KX-
TG5832AL only)
Outside calls can be transferred from one
handset to the other.
A conference call allows 2 handsets to
speak together with an outside party.
1 During an outside call, press
1 During an outside call, press
{INTERCOM}.
{INTERCOM}.
L The call will be put on hold.
L The call will be put on hold.
2 To page the other handset, press
2 To page the other handset, press
{handset[1]} or {handset[2]}.
{handset[1]} or {handset[2]}.
3 Wait for the paged party to answer.
3 When the paged party answers, press
{Conf} on your handset to establish a
conference call.
L The paged handset user can answer
by pressing {C}, {s}, or
{INTERCOM}.
L “Conference” will be displayed.
L If there is no answer, press {C} or
{s} to return to the outside call.
L To leave the conference, press
{OFF}. The other 2 parties can
continue the conversation.
4 To complete the transfer, press {OFF}.
Note:
Transferring a call without speaking to
the paged party
L The outside call can be put on hold by
pressing {HOLD} during a conference
call. Communications between
extensions are not suspended. Only the
person who placed the call on hold can
resume the conference by pressing
{Conf}.
1 During an outside call, press
{INTERCOM}, then press
{handset[1]} or {handset[2]}.
2 Press {OFF}.
L The outside call rings at the other
handset.
Note:
L If the paged party does not answer the
call, press {C} or {s} to return to the
call. If not answered within 1 minute, the
call will ring at your handset again. If you
still do not answer the call within 4
minutes, the call will be disconnected.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 32 Monday, March 14, 2005 4:28 PM
Programmable Settings
Guide to handset programming
For your reference, a chart of all programmable functions is printed below. Details for each
item can be found on the corresponding pages. To programme, press {MENU}, press {V}
or {^} to scroll through the menu, and press {>} or {Select} when the desired menu item
or setting is displayed.
Important:
L Before programming, make sure the handset and base unit are not being used. The
handset must be operated near the base unit and while off the base unit or charger.
Main menu
Sub-menu 1
Sub-menu 2
Page
Message play
Ringer setting
–
Ringer volume
Ringer tone
Interrupt tone
–
–
page 44
page 33
page 34
page 34
page 16
page 35
page 37
page 23
page 24
page 48
page 49
page 47
page 49
page 35
page 37
page 35
page 36
page 38
page 57
page 36
page 36
page 37
–
–
–
*1
Date and time
–
Voice enhancer
–
–
*1
Dial lock
–
–
*2
Copy phonebook
Copy 1 item
Copy all items
Set answering
–
–
*1
Initial setting
Ring count
*1
Recording time
*1
Remote code
Message alert
LCD contrast
Key tone
–
–
–
–
–
–
Auto talk
Set area code
Time adjustment
Set tel line
*1
*1
Set dial mode
*1
Set recall time
*1
Set line mode
Registration
–
*1 If you programme these settings using one of the handsets, you will not need to
programme the same item using the other handset (KX-TG5832AL only).
*2 KX-TG5832AL only
Note:
L To exit programming, press {OFF} at any time.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 33 Monday, March 14, 2005 4:28 PM
Programmable Settings
L To go back to the previous menu, press
{<} or {Back}, or press {>} or {Select}
while “(Go back)” is displayed.
Ringer settings
Handset ringer volume
4 levels (high/medium/low/off) are
available. The default setting is HIGH.
1 Press {MENU}.
2 Scroll to “Ringer setting” by
pressing {V} or {^}, then press {>}.
Ringer setting
3 Scroll to “Ringer volume” by pressing
{V} or {^}, then press {>}.
Ringer volume
4 Press {V} or {^} repeatedly to select
the desired volume.
Ringer volume
Low |||||| High
KBack dB SaveL
L To turn the ringer off, press {V}
repeatedly until “Off ?” is displayed.
5 Press {Save}.
Note:
L When the ringer volume is set to off, the
handset will display “Ringer off”, and
will not ring for outside calls. The
handset will ring at the low level for
intercom calls.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 34 Monday, March 14, 2005 4:28 PM
Programmable Settings
Handset ringer tone
Handset interrupt tone
You can change the ringer tone heard
when an outside call is received. There are
3 tones and 4 melodies. The default
setting is “Tone 1”.
This tone lets you know when you receive
a call while you are on an intercom call
(page 29).
“2” (default): The tone will sound 2 times.
“On”: The tone will sound for as long as the
line rings.
1 Press {MENU}.
“Off”: Turns this feature off.
2 Scroll to “Ringer setting” by
pressing {V} or {^}, then press {>}.
1 Press {MENU}.
2 Scroll to “Ringer setting” by
Ringer setting
pressing {V} or {^}, then press {>}.
3 Scroll to “Ringer tone” by pressing
3 Scroll to “Interrupt tone” by
{V} or {^}, then press {>}.
pressing {V} or {^}, then press {>}.
4 Press {V} or {^} repeatedly to select
Ringer tone
the desired setting.
5 Press {Save}, then press {OFF}.
4 Press {V} or {^} repeatedly to select
the desired setting.
Ringer tone
1=Tone 1
KBack dB SaveL
L You can also select the ringer tone by
pressing {1} to {7}.
L If the ringer volume has been turned
off, the handset will not ring.
5 Press {Save}, then press {OFF}.
Note:
L If you select one of the melody ringer
patterns, the ringer will continue to
sound for several seconds if:
– the caller hangs up before you answer
the call.
– another person answers the call using
another phone connected on the
same line.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 35 Monday, March 14, 2005 4:28 PM
Programmable Settings
Call options
Display options
Auto talk
Handset LCD contrast
When this feature is turned on, you can
answer a call by lifting the handset off the
base unit or charger without pressing
{C}. The default setting is OFF.
You can adjust the handset display
contrast. There are 6 levels. The default
setting is level 3.
1 Press {MENU}.
1 Press {MENU}.
2 Scroll to “Initial setting” by
2 Scroll to “Initial setting” by
pressing {V} or {^}, then press {>}.
pressing {V} or {^}, then press {>}.
3 Scroll to “LCD contrast” by pressing
3 Scroll to “Auto talk” by pressing {V}
{V} or {^}, then press {>}.
or {^}, then press {>}.
4 Press {V} or {^} repeatedly to select
4 Press {V} or {^} repeatedly to select
the desired setting.
“On” or “Off”.
5 Press {Save}, then press {OFF}.
5 Press {Save}, then press {OFF}.
Note:
L If you subscribe to Caller ID service and
want to view the caller’s information on
the handset display after lifting up the
handset to answer a call, turn off this
feature.
Voice enhancer
You can turn the voice enhancer feature on
or off. The default setting is OFF.
1 Press {MENU}.
2 Scroll to “Voice enhancer” by
pressing {V} or {^}, then press {>}.
3 Press {V} or {^} repeatedly to select
“On” or “Off”.
4 Press {Save}, then press {OFF}.
L When turned on, “J” will be
displayed.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 36 Monday, March 14, 2005 4:28 PM
Programmable Settings
3 Scroll to “Set tel line” by pressing
{V} or {^}, then press {>}.
Telephone settings
4 Scroll to “Set line mode” by pressing
{V} or {^}, then press {>}.
Recall time
The recall time depends on your telephone
exchange or host PBX.
You can select: “90ms” (milliseconds),
“100ms” (default), “110ms”, “250ms”,
“300ms”, “400ms”, “600ms”, or “700ms”.
5 Press {V} or {^} repeatedly to select
the desired setting.
6 Press {Save}, then press {OFF}.
Storing your area code
1 Press {MENU}.
We recommend storing your area code
before using Caller ID (page 25). Calls
from the same area will be recorded in the
caller list without the area code. You do not
have to remove it before calling back the
caller or storing in the phonebook.
2 Scroll to “Initial setting” by
pressing {V} or {^}, then press {>}.
3 Scroll to “Set tel line” by pressing
{V} or {^}, then press {>}.
4 Scroll to “Set recall time” by
1 Press {MENU}.
pressing {V} or {^}, then press {>}.
2 Scroll to “Initial setting” by
5 Press {V} or {^} repeatedly to select
pressing {V} or {^}, then press {>}.
the desired setting.
3 Scroll to “Set area code” by pressing
6 Press {Save}, then press {OFF}.
{V} or {^}, then press {>}.
Note:
4 Enter your area code (max. 8 digits).
L You can access Telstra’s “EASY CALL”
service by having the recall time set at
100 ms, and then follow Telstra’s “EASY
CALL” instructions to operate this
service.
L To correct a digit, press {<} or {>} to
move the cursor, then press
{CLEAR}. Enter the correct number.
5 Press {Save}, then press {OFF}.
L If the unit is connected via a PBX, certain
PBX functions (call transferring, etc.)
may not work correctly. Consult your
PBX supplier for the correct setting.
To erase your area code
Press and hold {CLEAR} in step 4, press
{Save}, then press {OFF}.
Line mode
The line mode is preset to “B” and
generally should not be adjusted. If “Line
in use” on the handset is not displayed
properly, the line mode selection is
incorrect. Set line mode to “A”.
1 Press {MENU}.
2 Scroll to “Initial setting” by
pressing {V} or {^}, then press {>}.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 37 Monday, March 14, 2005 4:28 PM
Programmable Settings
To turn dial lock off
1 Press {MENU}.
Other options
Dial lock
This feature prohibits making outside calls.
2 Scroll to “Dial lock” by pressing {V}
or {^}, then press {>}.
The default setting is OFF.
3 Enter the same password that was
Important:
entered when dial lock was turned on.
L When dial lock is turned on, only
phone numbers stored in the
phonebook as emergency numbers
(numbers stored with a # at the
beginning of the name) can be dialled
using the phonebook (page 21). We
recommend storing emergency
numbers in the phonebook before
using this feature.
4 Press {Save}.
5 Press {Yes}.
L “Dial lock off” will be displayed.
6 Press {OFF}.
Note:
L If you forget the password, consult your
nearest Panasonic service centre.
L When dial lock is turned on, you cannot
store, edit, or erase items in the
phonebook.
Handset key tone
You can select whether or not key tones
are heard when keys are pressed.
Includes confirmation tones and error
tones. The default setting is ON.
To turn dial lock on
1 Press {MENU}.
2 Scroll to “Dial lock” by pressing {V}
1 Press {MENU}.
or {^}, then press {>}.
2 Scroll to “Initial setting” by
3 Enter a 4-digit password.
pressing {V} or {^}, then press {>}.
L This password is required when
turning dial lock off. We recommend
writing the password down.
3 Scroll to “Key tone” by pressing {V} or
{^}, then press {>}.
4 Press {Save}.
4 Press {V} or {^} repeatedly to select
“On” or “Off”.
5 Press {Yes}.
5 Press {Save}, then press {OFF}.
L “Dial lock on” will be displayed.
6 Press {OFF}.
Re-registering the handset
If “No link to base. Move closer
to base, try again.” is displayed
even when the handset is near the base
unit, you may need to re-register the
handset to the base unit.
Note:
L If dial lock is turned on, the handset
displays “Dial lock”. While there are
missed calls, “Dial lock” is not
displayed when the handset is off the
base unit or charger.
Important:
L Make sure the base unit is not being
used.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 38 Monday, March 14, 2005 4:28 PM
Programmable Settings
L Have the handset and base unit near
each other when re-registering the
Time adjustment (Caller ID
handset.
subscribers only)
L KX-TG5832AL only:
Confirm the extension number of the
handset which has lost the
communication by placing the handset
on the base unit or charger.
If you re-register the handset using the
other handset’s extension number [1]
or [2], the other handset will not
function.
Using this feature, the unit’s date and time
setting will be automatically adjusted when
caller information is received. To turn this
feature on, select “Caller ID[auto]”
(default). To turn off, select “Manual”.
1 Press {MENU}.
2 Scroll to “Initial setting” by
pressing {V} or {^}, then press {>}.
1 Handset:
3 Scroll to “Time adjustment” by
Press {MENU}.
pressing {V} or {^}, then press {>}.
2 Scroll to “Initial setting” by
4 Press {V} or {^} repeatedly to select
pressing {V} or {^}, then press {>}.
“Manual” or “Caller ID[auto]”.
3 Scroll to “Registration” by pressing
5 Press {Save}, then press {OFF}.
{V} or {^}, then press {>}.
Note:
4 KX-TG5831AL base unit:
Press and hold {LOCATOR/
INTERCOM} until the CHARGE
indicator flashes.
L To use this feature, set the date and time
manually first (page 16).
KX-TG5832AL base unit:
Press and hold the locator/intercom
button that corresponds to the handset
you want to re-register ({LOCATOR/
INTERCOM 1} or {LOCATOR/
INTERCOM 2}) until the registering
handset number (H1 or H2) is
displayed.
L After the CHARGE indicator starts
flashing, the rest of the procedure
must be completed within 1 minute.
5 Handset:
Press {OK}, then wait until the handset
beeps.
L Registration is complete.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 39 Monday, March 14, 2005 4:28 PM
Programmable Settings
Programming via direct commands
You can also programme most features using “direct commands”—special codes that take
you directly to the feature you wish to programme and allow you to select the desired
setting. There is no need to scroll through the unit’s menus.
Details of each feature can be found on the corresponding pages.
1 Press {MENU}.
2 Enter the desired feature code (shown below).
3 Enter the desired setting code (shown below).
L This step may vary depending on the feature being programmed.
4 Press {Save}.
5 Press {OFF} to exit programming mode.
Direct commands chart
Feature
Feature code
Setting code
Page
Ringer volume
{1} {1}
{1}: Low {2}: Medium
page 33
{3}: High {0}: Off
Ringer tone
{1} {2}
{1}–{3}: Tone pattern 1–3
page 34
{4}–{7}: Melody pattern 1–4
Interrupt tone
Message play
Date and time
Voice enhancer
Dial lock
{1} {3}
{2}
{1}: On {2}: 2 times {0}: Off
–
page 34
page 44
page 16
page 35
page 37
page 35
page 37
page 35
page 36
page 57
page 36
{4}
Go to step 3 on page 16.
{1}: On {0}: Off
Go to step 3 on page 37.
{1}–{6}: Level 1–6
{1}: On {0}: Off
{1}: On {0}: Off
Go to step 4 on page 36.
–
{5}
{6}
LCD contrast
Key tone
{0} {1}
{0} {2}
{0} {3}
{0} {4}
{0} {5} {1}
{0} {5} {2}
Auto talk
Set area code
Set dial mode
Set recall time
{1}: 700 ms {2}: 600 ms
{3}: 400 ms {4}: 300 ms
{5}: 250 ms {6}: 110 ms
{7}: 100 ms {8}: 90 ms
Set line mode
Ring count
{0} {5} {3}
{1}: A {2}: B
page 36
page 48
{0} {6} {1}
{2}–{7}: 2–7 rings
{0}: Toll saver
39
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 40 Monday, March 14, 2005 4:28 PM
Programmable Settings
Feature
Feature code
Setting code
Page
Recording time
{0} {6} {2}
{1}: 1 minute
page 49
{2}: 2 minutes
{3}: 3 minutes
{0}: Greeting only
Remote code
{0} {6} {3}
Go to step 5 on page 47.
page 47
page 38
Time adjustment
{0} {9}
{1}: Caller ID[auto]
{0}: Manual
Handset registration
Message alert
{0} {0}
{0} {#}
{#} {1}
Go to step 4 on page 37.
{1}: On {0}: Off
page 37
page 49
page 23
Copy phonebook
Go to step 4 on page 23.
*1
(1 item)
Copy phonebook
(all items)
{#} {2}
–
page 24
*1
*1 KX-TG5832AL only
Note:
L If you make a mistake or enter the wrong code, press {OFF} then start again by
pressing {MENU}.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 41 Monday, March 14, 2005 4:28 PM
Answering System Features
Answering system
Recording your greeting
message
The unit contains an answering system
which can answer and record calls for you
when you are unavailable to answer the
phone.
For details about memory capacity, see
page 45.
You can record your own greeting
message (max. 2 minutes) that will be
played when the answering system
answers a call. If you do not record a
greeting message, a pre-recorded
greeting message will be used.
Important:
Sample greeting message: “This is (your
name). We are unable to answer the
phone right now. Please leave a message
after the beep. Thank you.”
L Only 1 person can access the answering
system (listen to messages, record a
greeting message, etc.) at a time.
L When callers leave messages, the unit
records the day and time of each
message. Make sure the date and time
have been set (page 16).
{GREETING REC}
{GREETING CHECK}
L You can select the caller’s recording
time (page 49).
{STOP}
MIC
1 Press {GREETING REC}.
L The unit announces “To record
greeting, press record again.”
2 Within 10 seconds, press {GREETING
REC} again.
3 After the unit beeps, speak clearly
about 20 cm away from the MIC.
L The display will show the elapsed
recording time.
4 To stop recording, press {GREETING
REC} or {STOP}.
Note:
L If the greeting message is less than 1
second long, the unit beeps 6 times and
announces, “Your greeting was not
recorded. Record your greeting again.”
41
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 42 Monday, March 14, 2005 4:28 PM
Answering System Features
To play back the greeting message
Press {GREETING CHECK}.
Turning the answering
system on/off
Erasing your greeting message
Press {GREETING CHECK}, and then
press {ERASE} while your greeting
message is playing.
ANSWER ON
indicator
L If you do not re-record your greeting
message, the unit will use a pre-
recorded greeting message.
{ANSWER ON}
{<}, {>}
Pre-recorded greeting message
If you do not record a greeting message,
one of 2 pre-recorded messages will be
played when a call is received depending
on the caller’s recording time (page 49).
Press {ANSWER ON}.
L When the answering system is turned
on, the ANSWER ON indicator lights
and the unit announces “Answer set”
and the day and time.
– When the recording time is set to
“1min”, “2min”, or “3min”:
“Hello, we are not available now. Please
leave your name and phone number
after the beep. We will return your call.”
L When the answering system is turned
off, the ANSWER ON indicator turns off
and the unit announces “Answer off”.
– When the recording time is set to
“Greeting only”:
“Hello, we are not available now. Please
call again. Thank you for your call.”
To play back the pre-recorded greeting,
press {GREETING CHECK}.
Screening your calls
While a caller is leaving a message, you
can listen to the call through the base unit’s
speaker. To adjust the speaker volume,
press {>} or {<} repeatedly.
You can answer the call by pressing {C}
or {s}.
To turn off the call screening feature
Turn the base unit’s speaker volume off by
pressing {<} until “0” is displayed.
Note:
L If you adjust the speaker volume while
listening to messages or talking on the
intercom, the speaker volume for call
screening will be turned on again.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 43 Monday, March 14, 2005 4:28 PM
Answering System Features
Note:
L The display shows the message number
during playback.
Listening to messages
When new messages have been
recorded:
L During playback, the unit will announce
the day and time that each message
was recorded. (Voice time/day stamp)
– The MESSAGE indicator on the base
unit will flash.
L At the end of the last message, the unit
– The message indicator on the handset
will flash slowly if the message alert
feature is turned on (page 49).
announces “End of final message”.
To adjust the speaker volume
9 levels (high to off) are available. Press
{>} or {<} repeatedly while using the
answering system.
The base unit display will show the number
of messages (old and new) recorded by
the answering system.
Example: The total number of recorded
messages is 10.
Repeating a message
Press {<} while listening to the
message.
L If pressed within the first 5 seconds of a
message, the previous message will be
played.
Listening to messages using
the base unit
Skipping a message
Press {>} to play the next message.
Pausing message playback
Press {STOP}.
{ERASE}
{<}, {>}
L To resume playback, press
{MESSAGE}.
L To stop playback completely, press
MESSAGE
indicator
{STOP} again.
{MESSAGE}
{STOP}
Erasing a specific message
Press {ERASE} while listening to the
message you want to erase.
{<}, {>}
Press {MESSAGE}.
Erasing all messages
L The unit will announce the number of
new messages and will play back the
new messages.
1 Press {ERASE} while the base unit is
not being used.
L The unit will announce “To erase all
messages, press ERASE again.”
L When you have no new messages, the
unit will announce “No new messages.
All message playback”, and will play
back all messages.
2 Within 10 seconds, press {ERASE}
again.
L The unit will announce “No
messages”.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 44 Monday, March 14, 2005 4:28 PM
Answering System Features
Note:
L At the end of the last message, the unit
announces “End of final message”.
L Caller information for the erased
messages will remain in the caller list.
Voice guidance
If you do not press any buttons after the
last message is played back, the unit’s
voice guidance starts. Operate the
answering system by following the
guidance as necessary.
Listening to messages using
the handset
The unit will announce “Press 4 to play
back new messages. Press 5 to play back
all messages.”
L You can press buttons for other
playback options (see below) even if the
voice guidance has started.
{MENU}
{Select}
L If you do not press any button within 10
seconds after the voice guidance, the
handset returns to standby mode.
{OFF}
Answering system commands
You can also operate the answering
system by pressing dial keys.
To use the following commands, press
{MENU}, then press {Select} at
“Message play”.
When new messages have been
recorded, “New message” is displayed.
1 Press {MENU}.
Key
Command
2 Press {Select} at “Message play”.
{1} or {<} Repeat message (during
L The unit will announce the number of
new messages, and will play back the
new messages.
*1
playback)
{2} or {>} Skip message (during
playback)
L To switch to the receiver and to listen
to the messages with privacy, press
{C}. You can switch back to the
speaker by pressing {s}.
L When you have no new messages,
the unit will announce “No new
messages. All message playback”,
and will play back all messages.
{4}
{5}
{8}
{9}
{0}
Play new messages
Play all messages
Turn answering system on
*2
Stop playback
Turn answering system off
{CLEAR} Erase this message (during
or {*}{4} playback)
L After the last message is played
back, the unit’s voice guidance starts.
Follow the guidance as necessary.
{*}{5}
Erase all messages
*1 If pressed within the first 5 seconds of a
message, the previous message will be
played.
3 Press {OFF} when finished.
Note:
*2 To resume operation, press a command
key within 15 seconds, or the voice
guidance will start.
L Adjust the speaker or receiver volume
using {V} or {^}.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 45 Monday, March 14, 2005 4:28 PM
Answering System Features
Calling back (Caller ID subscribers
only)
Memory capacity
If Caller ID information was received for
the call, you can call the caller back while
listening to a message.
The total recording capacity (including
your greeting message and caller
messages) is about 15 minutes. A
maximum of 64 messages (including a
greeting message) can be recorded.
Press {Call} during playback.
Note:
L If message memory becomes full:
– “E” flashes on the base unit.
– the ANSWER ON indicator flashes
rapidly (if the answering system is
turned on).
L To edit the number before calling back,
press {Edit} and edit the number (page
27). Press {Call}, {C}, or {s}.
– the unit announces “Memory full”
when operating the answering
system.
To record additional messages, erase
unnecessary messages.
L If less than 3 minutes of recording time is
available, the unit will announce the
remaining recording time when
operating the answering system.
L Messages are retained even if a power
failure occurs. All messages are saved
until you erase them. (Flash memory
message backup)
L The total recording capacity may be
reduced by the calling party’s
background noise.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 46 Monday, March 14, 2005 4:28 PM
Answering System Features
Voice guidance
Remote operation
During remote operation, the unit’s voice
guidance will prompt you to press {1} to
perform a specific operation, or press {2}
to listen to more available operations.
Operations are presented by voice
guidance in the following order:
Using a touch tone phone, you can call
your phone number from outside and
access the unit to listen to messages. The
unit’s voice guidance will prompt you to
press certain dial keys to perform different
operations.
– Play back all messages
– Play back new messages
– Record a message
Important:
L In order to operate the answering
system remotely, you must first set a
remote code (page 47). This code must
be entered each time you operate the
answering system remotely.
– Erase all messages
Note:
L If you do not press any dial keys within
10 seconds after a voice guidance
prompt, the unit will announce, “Thank
you for your call” then disconnect your
call.
Using the answering system
remotely
L If less than 3 minutes of recording time is
available, the unit will announce the
remaining recording time after the last
message is played back.
1 Dial your phone number from a touch
tone phone.
L If the ring count is set to “Toll
saver” (page 48), the number of
rings you hear will indicate whether or
not you have new messages.
L If the unit announces “Memory full”,
erase unnecessary messages.
Remote commands
2 After the greeting message starts, enter
You can press dial keys to access certain
answering system functions without
waiting for the voice guidance to prompt
you.
your remote code.
L The unit will announce the number of
new messages, and will play back the
new messages.
Key
Remote command
3 After 3 seconds, the voice guidance will
start. Follow the voice guidance as
necessary.
{1}
Repeat message (during
*1
playback)
{2}
Skip message (during
playback)
4 When finished, hang up.
{4}
{5}
{9}
{0}
Play new messages
Play all messages
Note:
L When you press a key, press firmly.
L You can hang up at any time.
L You can ignore the voice guidance and
control the unit using remote
commands.
*2
Stop
Turn answering system off
{*}{4} Erase this message (during
playback)
{*}{5} Erase all messages
46
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 47 Monday, March 14, 2005 4:28 PM
Answering System Features
*1 If pushed within the first 5 seconds of a
message, the previous message will be
Answering system
settings
played.
*2 To resume operation, enter a remote
command within 15 seconds, or the
voice guidance will start.
Remote code
A remote code must be entered when
operating the answering system remotely.
This code prevents unauthorised parties
from listening to your messages remotely.
Store any 2-digit number (00–99). The
default setting is “11”.
Turning on the answering system
remotely
If the answering system is off, you can turn
it on remotely.
1 Dial your phone number.
1 Press {MENU}.
2 Let the phone ring 15 times.
L The unit will answer your call with the
2 Scroll to “Initial setting” by
greeting message.
pressing {V} or {^}, then press {>}.
L You can hang up, or if you call from a
touch tone phone, you can enter your
remote code and begin remote
operation (page 46).
3 Scroll to “Set answering” by pressing
{V} or {^}, then press {>}.
4 Scroll to “Remote code” by pressing
{V} or {^}, then press {>}.
Skipping the greeting message to leave
a message
You can leave a message just as any
outside caller can. Call your phone
number, then press {*} to skip the
greeting message and record your
message after the beep.
5 Select the desired remote code by
entering a 2-digit number (00–99).
6 Press {Save}, then press {OFF}.
Note:
L To confirm the remote code, repeat
steps 1 to 4. Press {OFF} when finished.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 48 Monday, March 14, 2005 4:28 PM
Answering System Features
This will allow the Voice Mail to receive
any messages.
Ring count
You can change the number of times the
phone rings before the unit answers calls.
You can select “2”, “3”, “4” (default), “5”,
“6”, “7”, or “Toll saver”.
“Toll saver”: The unit answers on the
2nd ring when new messages have been
recorded, and on the 4th ring when there
are no new messages. If you call your
phone from outside to listen to new
messages (page 46), you will know that
there are no messages when the phone
rings for the 3rd time. You can then hang
up without being charged for the call.
This unit does not have a visual indicator
to indicate if there are new messages in
your Voice Mail service. Your Service
Provider may use a “Stutter” dial tone to
indicate that you have Voice Mail left.
L To use the unit’s answering machine
rather than the Voice Mail service
provided by your Service Provider,
please consult your Service Provider to
have it removed or deactivated
permanently or temporarily.
Alternatively you can leave this service
connected and change the “Ring
count” to a shorter duration on your unit
so your unit’s answering machine can
pick up the call prior to the Voice Mail
provided by your Service Provider.
1 Press {MENU}.
2 Scroll to “Initial setting” by
pressing {V} or {^}, then press {>}.
Note:
3 Scroll to “Set answering” by pressing
{V} or {^}, then press {>}.
L Provider Voice Mail can capture
messages that can be missed while the
customer is on the Internet.
4 Scroll to “Ring count” by pressing {V}
or {^}, then press {>}.
5 Press {V} or {^} repeatedly to select
the desired setting.
L You can also select the ring count by
pressing {0} (“Toll saver”), or {2}
to {7}.
6 Press {Save}, then press {OFF}.
For Telstra Homeline service
subscribers
To receive Voice Mail and use answering
system properly, please note the following:
L “Voice Mail” is a service provided by
your Service Provider. You will need to
first subscribe or activate this service
through your Service Provider. Consult
your Service Provider on how to operate
this service and how you will be notified
that you have messages on your Voice
Mail.
To use this service you will be required
to leave your answering machine off on
your unit.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 49 Monday, March 14, 2005 4:28 PM
Answering System Features
Caller’s recording time
Message alert
You can change the maximum message
recording time allotted to each caller.
“1min”, “2min”, or “3min” (default): Caller
messages are limited to 1 minute to 3
minutes.
You can select whether or not the
message indicator on the handset will
flash when new messages have been
recorded (page 43). The default setting is
OFF.
“Greeting only”: The unit plays the
greeting message but does not record
caller messages.
1 Press {MENU}.
2 Scroll to “Initial setting” by
pressing {V} or {^}, then press {>}.
1 Press {MENU}.
3 Scroll to “Message alert” by pressing
2 Scroll to “Initial setting” by
{V} or {^}, then press {>}.
pressing {V} or {^}, then press {>}.
4 Press {V} or {^} repeatedly to select
3 Scroll to “Set answering” by pressing
“On” or “Off”.
{V} or {^}, then press {>}.
5 Press {Save}, then press {OFF}.
4 Scroll to “Recording time” by
pressing {V} or {^}, then press {>}.
Note:
L The message indicator will not flash for
new messages while the handset is in
use.
5 Press {V} or {^} repeatedly to select
the desired setting.
L You can also select the recording
time by pressing {1} to {3}, or {0}
(“Greeting only”).
L While message alert is on, battery
operating time will be shortened (page
12).
6 Press {Save}, then press {OFF}.
Note:
L If message memory becomes full, the
unit will automatically switch to the
“Greeting only” mode.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 50 Monday, March 14, 2005 4:28 PM
Useful Information
Wall mounting
Base unit
The base unit can be mounted on a wall.
1 Connect the AC adaptor.
Fasten the AC adaptor cord.
Hook
To power
outlet
2 Tuck the telephone line cord inside the wall mounting adaptor (1).
Connect the telephone line cord (2).
1
2
3 Insert the hooks on the wall mounting adaptor into the holes (A) and (B) on the base
unit.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 51 Monday, March 14, 2005 4:28 PM
Useful Information
4 Adjust the adaptor to hold the base unit, then push it in the direction of the arrow until
it clicks into place.
5 Drive the screws (not included) into the wall using the wall mount template (see below).
Connect the telephone line cord. Mount the unit, then slide it down.
L Raise the antennas.
Screws (not included)
83 mm
To telephone plug
connected to socket
Wall mount template for the base unit
83 mm
51
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 52 Monday, March 14, 2005 4:28 PM
Useful Information
To remove the wall mounting adaptor
While pushing down the release levers (1), remove the adaptor (2).
2
52
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 53 Monday, March 14, 2005 4:28 PM
Useful Information
Charger (KX-TG5832AL only)
The charger can be wall mounted, as shown below.
1 Connect the AC adaptor.
2 Drive the screws (not included) into the wall using the wall mount template (see below).
3 Mount the charger (1).
4 Slide it down (2) and to the right (3) until it is secure.
25.4 mm
1
2
3
Screws
To power
outlet
Wall mount template for the charger
25.4 mm
53
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 54 Monday, March 14, 2005 4:28 PM
Useful Information
Belt clip
Headset (optional)
You can hang the handset on your belt or
pocket using the included belt clip.
Connecting an optional headset to the
handset allows hands-free phone
conversations. Please use only a
Panasonic headset. See page 5 for
compatible headset and ordering
information.
To attach the belt clip
To connect an optional headset to the
handset
To remove the belt clip
While pressing the top of the clip (1), pull
the right edge in the direction of the arrow
(2).
Headset jack
2
1
Note:
L Only telecommunications compliance
labelled headsets should be plugged
into the headset jack on the handset.
L To switch to the speakerphone, press
{s}. To return to the headset, press
{C}.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 55 Monday, March 14, 2005 4:28 PM
Useful Information
Error messages
If the unit detects a problem, one of the following messages will be displayed on the
handset.
Display message
Cause & solution
*1
Busy
L The called handset is in use.
L The handset you tried to copy phonebook items to is in
*1
use.
*1
L The handset you are calling is too far from the base unit.
Error!!
L When you tried to register the handset, the handset and
the base unit could not link for some reason, such as
interference from electrical appliances. Move the handset
and the base unit away from the electrical appliances and
try again.
L The other handset tried to send phonebook items to you
but there was an error. Have the other handset user re-
*1
send the items to you (page 23).
L The entered password was wrong in programming dial
lock. Enter the correct password.
---Incomplete---
Phonebook full
L When the phonebook item(s) was(were) sent to another
handset, the handset’s phonebook memory was full and
copying stopped. Press {OFF} to exit. Erase items from
the other handset’s phonebook (page 22). When
phonebook memory is available, you can copy all
phonebook items (page 24) or individual items one by one
*1
(page 23).
No link to base.
Move closer to
base, try again.
L The handset has lost communication with the base unit.
Move closer to the base unit, and try again.
L Confirm that the base unit’s AC adaptor is plugged in.
L Raise the base unit antennas.
L The handset’s registration may have been cancelled. Re-
register the handset (page 37).
Phonebook full
No items stored
L There is no space to store new items in the phonebook.
Erase unnecessary items (page 22).
L Your phonebook or redial list is empty.
Please lift up
and try again.
L A handset button was pressed while the handset was on
the base unit or charger. Lift the handset and press the
button again.
System is busy.
Please try again
later.
L The handset has lost communication with the base unit.
Move closer to the base unit and try again.
*1
L More than one unit is in use. Try again later.
L Another user is listening to messages. Try again later.
Dial locked
L Dial lock is turned on. To turn it off, see page 37.
*1 KX-TG5832AL only
55
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 56 Monday, March 14, 2005 4:28 PM
Useful Information
Troubleshooting
General use
Problem
Cause & solution
The unit does not work.
L Make sure that the battery is installed correctly (page
10).
L Check the connections (page 9).
L Fully charge the battery (page 11).
L Clean the charge contacts and charge again (page 11).
L Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.
L Re-install the battery (page 10) and fully charge it.
The display shows “No
link to base. Move
closer to base, try
again.” and an alarm
tone sounds.
L The handset is too far from the base unit. Move closer
and try again.
L Plug in the base unit’s AC adaptor.
L Raise the base unit antennas.
L If the above remedies do not solve the problem, the
handset may have lost communication with the base
unit. Register the handset again (page 37).
I cannot hear a dial tone.
L Confirm that the telephone line cord is connected (page
9).
L Disconnect the unit from the telephone line and connect
a known working telephone. If the working telephone
operates properly, contact our service personnel to
have the unit repaired. If the working telephone does
not operate properly, contact your telephone company.
Programmable settings
Problem
Cause & solution
I cannot programme
items.
L Programming is not possible while the handset and
base unit are being used.
L Do not pause for over 1 minute while programming.
L Move closer to the base unit.
L While another user is listening to messages or the
answering system is answering a call, you cannot
programme. Try again later.
While programming, the
handset starts to ring.
L A call is being received. Answer the call and start again
from the beginning after hanging up.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 57 Monday, March 14, 2005 4:28 PM
Useful Information
Making/answering calls, Intercom
Problem
Cause & solution
Static is heard, sound
cuts in and out.
L Move the handset and the base unit away from other
electrical appliances.
Interference from other
electrical units.
L Move closer to the base unit.
L Raise the base unit antennas.
L Turn on the clarity booster feature (page 20).
L If your unit is connected to a telephone line with ADSL
service, we recommend connecting a noise filter
between the base unit and the telephone line jack.
Contact your ADSL provider for details.
The handset does not
ring.
L The ringer volume is turned off. Adjust it (page 33).
I cannot make a call.
L If the base unit (including answering system) or the
other handset is in use, you may not be able to make a
call. Try again later.
L While listening to messages using the handset, you
cannot make a call. Exit by pressing {OFF}.
L Dial lock is turned on. To turn it off, see page 37.
L If the above remedies do not solve the probrem, set the
dialling mode. Press {MENU} {0} {5} {1} {Save}
{OFF}.
L The unit is not designed to be used with rotary (pulse
dialling) services.
I cannot redial by
pressing {REDIAL}.
L If the last number dialled was more than 48 digits long,
the number will not be redialled correctly.
L If you press {REDIAL} after you have started dialling,
this button functions as the {PAUSE} button. To redial,
do not dial any numbers before pressing {REDIAL}.
L Dial lock is turned on. To turn it off, see page 37.
I cannot have a
conversation using the
headset.
L Make sure that an optional headset is connected
properly (page 54).
L If “SP-phone” is displayed on the handset, press {C}
to switch to the headset.
L Use only the Panasonic KX-TCA88AL headset.
I cannot page the
L The called handset is too far from the base unit.
handset or base unit.
L The called unit is in use. Try again later.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 58 Monday, March 14, 2005 4:28 PM
Useful Information
Phonebook
Problem
Cause & solution
I cannot store an item in
the phonebook.
L You cannot store an item in the phonebook while the
handset is in talk, speakerphone or intercom mode, or
while listening to messages.
L Do not pause for over 1 minute while storing.
L Dial lock is turned on. To turn it off, see page 37.
While storing an item in
the phonebook, the
L A call is being received. Answer the call and start again
from the beginning after hanging up.
handset starts to ring.
Copying stopped with an
item displayed.
L The destination handset may have lost communication
with the base unit, or the destination handset user may
have pressed {C} or {s}.
The displayed phonebook item was not copied to the
handset. Press {OFF}. Confirm that the destination
handset is in standby mode (i.e., not in use) and try
again.
The display exits the
phonebook while
searching.
L The handset automatically exits after 1 minute of
inactivity.
Caller ID
Problem
Cause & solution
The handset does not
display the caller’s phone
number.
L You have not subscribed to Caller ID service. Contact
your telephone company to subscribe.
L If your unit is connected to any additional telephone
equipment such as Caller ID box or wireless telephone
jack, disconnect the unit from the equipment and plug
the unit directly into the wall jack.
L If your unit is connected to a telephone line with ADSL
service, we recommend connecting a noise filter
between the base unit and the telephone line jack.
Contact your ADSL provider for details.
L Other telephone equipment may be interfering with this
unit. Disconnect the other equipment and try again.
L The caller requested not to send caller information
(page 25).
L If a call is being transferred to you, the caller information
will not be displayed.
The display exits the
L The handset automatically exits after 1 minute of
caller list while searching.
inactivity.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 59 Monday, March 14, 2005 4:28 PM
Useful Information
Answering system
Problem
Cause & solution
I cannot listen to
messages from a remote
location.
L A touch tone phone is required for remote operation.
L Press the remote code correctly and press each key
firmly (page 46).
L The answering system is off. Turn it on (page 47).
The other party
complains that they
cannot leave a voice
message.
L The recording time is set to “Greeting only”. Select
“1min”, “2min”, or “3min” (page 49).
L The memory is full. Erase unnecessary messages
(page 43).
“E” flashes and the
ANSWER ON indicator
flashes rapidly. No new
messages are recorded.
L Message memory is full. Erase unnecessary messages
(page 43).
I cannot operate the
answering system.
L Someone is operating the answering system.
L If someone is talking on a conference call, you cannot
operate the answering system. Try again later.
During message
L A call is being received. Answer the call and start again
playback, the unit rings
and cancels playback.
from the beginning after hanging up.
The message indicator
on the handset flashes
slowly.
L New messages have been recorded. Listen to the new
messages (page 43) or turn the message alert off (page
49).
When you play back
messages or turn on the
answering system, the
base unit and handset
announce the day and
time incorrectly.
L Set the date and time again (page 16).
Battery charge
Problem
Cause & solution
“Recharge battery” is
displayed, 7 flashes
or the handset beeps
intermittently.
L Fully charge the battery (page 11).
“Charge for 6h” and
8 are displayed and
the handset does not
work.
L The battery has been discharged. Fully charge the
battery (page 11).
59
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 60 Monday, March 14, 2005 4:28 PM
Useful Information
Problem
Cause & solution
I charged the battery fully,
but “Recharge
battery” is still
L Clean the charge contacts and charge again (page 11).
L The battery may need to be replaced (page 12). If you
install a new battery, fully charge it (page 11).
displayed and/or 7
continues to flash, or
“Charge for 6h” and
8 are displayed.
The CHARGE indicator
does not go out after the
battery has been
charged.
L This is normal.
The handset display is
blank.
L Confirm that the battery is properly installed.
L Fully charge the battery (page 11).
Power failure
Problem
Cause & solution
The unit will not function.
L This product is not designed to make calls in the event
of a power failure. We recommend connecting a
standard telephone to the same telephone line in the
event that emergency calls need to be made during a
power failure (page 9).
60
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 61 Monday, March 14, 2005 4:28 PM
Useful Information
Instructions to customer
Installation
Attached to this apparatus is an approval label. This label is evidence that it is a “Permitted
Attachment” which has been authorised to be connected to your telephone service.
Conditions relating to connection and operation of this Permitted Attachment are
contained in Telecommunications General By-Law 220 (5).
You are authorised to install this Permitted Attachment yourself by plugging it into the line
socket of any regular telephone. You may connect it in place of your existing telephone or
to any spare telephone socket installed in your premises.
To disconnect your existing telephone you must first remove its plug from the line socket.
You can then insert the plug of your Permitted Attachment into the socket and use your
equipment.
If the plug of your existing telephone cannot be readily removed, you will have to remove
the screw securing it. To do this proceed as follows:
1. Loosen screw “A” sufficiently to remove the socket cover. (See Fig. 1.)
2. Remove screw “B” and withdraw the plug. (See Fig. 2.)
3. Replace screw “B”. (See Fig. 3.) Ensure that it screws completely into the socket
recess. (If the screw is too long, increase the hole depth or replace the screw with one
5 mm shorter.)
4. Replace socket cover and tighten screw “A”. (See Fig. 4.)
SOCKET
PLUG
SCREW
“B”
SCREW “A”
Fig. 2
Fig. 1
TELEPHONE CORD
Connect to the PLUG
(
)
as shown in Fig. 1.
SCREW “A”
SCREW “B”
SOCKET
Fig. 4
Fig. 3
61
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 62 Monday, March 14, 2005 4:28 PM
Useful Information
If you are satisfied with the operation of your telephone service after plugging in your
Permitted Attachment, your installation is completed.
You will be unable to connect this Permitted Attachment if your telephone service consists
only of a wall phone or an old style telephone which is not connected by means of a
modern plug and socket. In such cases a new socket will need to be installed.
Should the Permitted Attachment not operate when plugged into a socket, it is either faulty
or unsuitable for operation with your telephone service. It should be returned to the store
where purchased or an Authorised Service Centre.
Service difficulties
If at any time a fault occurs on your telephone service, carry out the following checks
before you call for service:
L Disconnect the Permitted Attachment and try using the service with the normal
telephone.
L If the telephone service then operates satisfactorily, the fault is in your Permitted
Attachment. Leave the Permitted Attachment disconnected and report the fault to its
supplier or agent to arrange for repair.
L If when using the telephone the service is still faulty, report the fault to “Service
Difficulties and Faults” for attention.
You are required to keep this Permitted Attachment in good working order while it is
connected to your telephone service. Its construction or internal circuit must not be
modified in any way without permission.
WARNING:
This cordless telephone system does not incorporate provision for secrecy of
conversations. Appropriately tuned radio equipment and other cordless telephone
systems in close proximity may be used by a third party to monitor and possibly interrupt
conversations in progress when this system is on radio operation.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 63 Monday, March 14, 2005 4:28 PM
Useful Information
Charger (KX-TG5832AL only)
Technical information
Operating environment:
5 °C – 40 °C
Base unit
Dimensions:
Approx. height 71 mm x width 88 mm x
depth 100 mm
Operating environment:
5 °C – 40 °C
Frequency:
5.76 GHz – 5.84 GHz
Mass (Weight):
Approx. 110 g
Dimensions:
Approx. height 95 mm x width 174 mm x
depth 143 mm
Power consumption:
Standby: Approx. 1.5 W
Maximum: Approx. 3.5 W
Mass (Weight):
Approx. 320 g
Power supply:
AC adaptor (230–240 V AC, 50/60 Hz)
Power consumption:
Standby: Approx. 2.4 W
Maximum: Approx. 5.5 W
Note:
L Design and specifications are subject to
change without notice.
Power supply:
AC adaptor (230–240 V AC, 50/60 Hz)
L The illustrations in these instructions
may vary slightly from the actual
product.
Handset
Operating environment:
5 °C – 40 °C
Frequency:
5.76 GHz – 5.84 GHz
Dimensions:
Approx. height 173 mm x width 48 mm x
depth 33 mm
Mass (Weight):
Approx. 170 g
Power supply:
Ni-MH battery (3.6 V, 830 mAh)
Security codes:
1,000,000
63
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 64 Monday, March 14, 2005 4:28 PM
Index
G Greeting message: 41
H Handset locator: 29, 30
Headset, optional: 54
Hold: 19
Index
A Accessories: 5
Answering calls: 18
Answering system: 41
Area code: 36
I
Installation
AC adaptor: 9
Base unit: 9
Charger: 9
Auto talk: 18, 35
B Backlit display: 15
Backlit handset keypad: 15
Base unit location: 8
Battery
Telephone line cord: 9
Intercom
Call: 29
Paging: 29
Charge: 11
Interrupt tone: 34
Installation: 10
Performance: 12
Replacement: 12
Strength: 11
K Key tone: 37
L
LCD contrast: 35
Light-up ID: 26
Line mode: 36
Listening to messages
Base unit: 43
Handset: 44
Touch tone phone: 46
Belt clip: 54
C Caller ID service: 25
Caller list
Calling back: 26
Editing: 27
Erasing: 28
Storing: 27
Viewing: 26
Call screening: 42
Call share: 20
Call waiting Caller ID: 25
Call waiting tone: 25
Chain dial: 23
Clarity booster: 20
Conf (Conference): 31
Conference calls: 31
Controls: 13
M Making calls: 17
Memory capacity: 45
Message alert: 49
Microphone
Base unit: 29, 41
Handset: 17
Mute: 19
N Navigator key: 14
Noise: 8
P
Pause: 20
Phonebook
Adding: 21
Calling: 22
Copying: 23, 24
Editing: 22
Erasing: 22
Names: 21
Power failure: 9, 16, 60
Copy phonebook: 23, 24
D Date and time: 16
Dial lock: 37
Display
Base unit: 15
Handset: 15
R Recall button: 20
Recall time: 36
E
Emergency numbers: 21
Erasing all messages: 43, 44, 46
Erasing a message: 43, 44, 46
Error messages: 55
Recording time: 49
Redial: 17
Redial list: 18
Registration: 37
Remote code: 47
Remote operation: 46
Extension number: 30
F
Function menu
Direct commands: 39
Table: 32
64
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 65 Monday, March 14, 2005 4:28 PM
Index
Ring count: 48
Ringer
Tone: 34
Volume: 33
Ringer ID: 25
Ringer off: 18, 33
S
T
Safety instructions: 6
Soft keys: 15
SP-phone: 17
Technical information: 63
Time adjustment: 38
Toll saver: 48
Transferring a call: 31
Troubleshooting
Answering system: 59
Battery charge: 59
Caller ID: 58
General use: 56
Making/answering calls, Intercom:
57
Phonebook: 58
Power failure: 60
Programmable settings: 56
V
VE (voice enhancer): 19
Voice enhancer: 19, 35
Voice guidance: 44, 46
Volume control
Base unit: 43
Handset receiver: 17
Handset speaker: 17
W Wall mounting
Base unit: 50
Charger: 53
65
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 66 Monday, March 14, 2005 4:28 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 67 Monday, March 14, 2005 4:28 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TG5831_5832AL.book Page 68 Monday, March 14, 2005 4:28 PM
N52
Copyright:
This material is copyrighted by Panasonic Communications Co., Ltd., and may be
reproduced for internal use only. All other reproduction, in whole or in part, is prohibited
without the written consent of Panasonic Communications Co., Ltd.
© 2005 Panasonic Communications Co., Ltd. All Rights Reserved.
Sales Department:
Panasonic Australia Pty. Limited
Austlink Corporate Park, 1 Garigal Road, Belrose NSW 2085, Australia
Manufacturer:
Panasonic Communications Co., Ltd.
1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan
PQQX14658ZA DM0305PY0
Download from Www.Somanuals.com. All Manuals Search And Download.
|