OWNER'S MANUAL
68CM CORDLESS REMOTE COLOUR TELEVISION
MODEL: 6825G
Type Tested
Electrical
Safety
AS/NZS 3250 Lic 4166
Standards Australia
APP No: N15899
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL:(02)9313 7111
FAX:(02)9313 7555
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA:1300 657 888
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Features
Hyperband
Intellectualized I2C bus control
256 preset channels
Full function remote control
AV input & output terminals, DVD input terminals
Intellectualized remote controller caller
Automatic channel preset
Clock/Game/Calendar
ON timer/OFF timer
Channel Exchange
Selectable picture and selectable sound
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Cautions
Safety Cautions
When any unusual situation occurs, turn off the
power supply at once and remove the plug from the
wall outlet. Contact a qualified service department in
your local area.
1
2
Do not expose the TV set to rain or excessive
moisture. Avoid using the set in very warm or
damp places and never use it in a bathroom.
3
When cleaning dust off the picture tube disconnect
the power first. You can wipe lightly with a piece of
dry, clean and soft cloth.
4
Avoid exposing the set to direct sunlight and other
sources of heat to prevent damage to the cabinet
and components.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
!
This TV set can operate on an AC power of 240V, 50HZ. You must not use a
power supply of any other type.
5
High voltage exists in this TV set. Do not remove the
cover
6
Do not cover the ventilating hole in the cabinet
Keep a space of more than 5cm from the walls to the
TV set to ensure adequate ventilation.
7
If the power cord or the plug is damaged contact a
qualified service department for service.
8
When the TV set is to be left unattended for a long
period of time, turn off the power supply and remove
the plug from the wall outlet.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification of Controls
Front
1. TV/VIDEO input select.
2. Volume up; menu item adjust.
3. Volume down; menu item adjust.
4. To enter menu operation.
5. Channel up; menu item select.
6. Channel down; menu item select.
7. To call remote controller.
8. AV3 inputs (VIDEO, AUDIO L/MONO, R)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Back
3
1
2
4
5
6
1. Antenna input.
2. DVD inputs (VIDEO: Y, CB , CR , AUDIO L/MONO, R).
3. AV 2 inputs (VIDEO, AUDIO L/MONO, R).
4. S-VIDEO input.
5. AV outputs (VIDEO, AUDIO L/MONO, R).
6. AV 1 inputs (VIDEO, AUDIO L/MONO, R).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification of Controls
(continued)
Remote Controller
The switch of the remote
controller caller
Power on/standby
Direct channel selector
TV/VIDEO input select
Previous channel
Colour and sound system select
To enter menu operation
Volume up/dowm select;
menu item adjust
Channel up/down select;
menu item select
Channel edit
Picture mode select
To enter game/Serve as confirm
button in GOBANG game
Game controller
To enter/exit game menu
To mute the sound
Program scanning
Sleep timer
Sound mode select
On-screen call
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective range of the Remote
Installing batteries
1
Open the battery cover.
2
Install two "AAA" batteries
matching the +/- polarities
of the battery to the +/-
marks inside the battery
compartment.
3
Replace the battery cover.
! Notes:
When there is an obstacle between the TV and the
transmitter, the transmitter may not operate.
When direct sunlight, and incandescent lamp,
fluorescent lamp or any other strong light shines on
the REMOTE SENSOR of the TV the remote
operation may be unstable.
!
Notes:
The battery life should be about one year under
normal use. Do not try to recharge batteries not
intended to be recharged.
Use only the size and type of batteries
specified. Do not mix different types of batteries
together or old batteries with fresh ones.
When the remote control will not be used for a
long period of time or when the batteries are
worn out, remove the batteries.
Do not throw the batteries into a fire. Dispose of
used batteries in the specified manner.
Do not drop, dampen or disassemble the
remote control.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL the unit in a room where direct light will not fall upon the screen.
Total darkness or a reflection on the picture screen may cause eyestrain.
Soft and indirect lighting is recommended for comfortable viewing.
Installation
Antenna installation
Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial
must be used. The exact type and position of the aerial will depend upon your particular area.
Notes:
!
It is recommended that the 75-ohm coaxial cable be used to eliminate interference
and noise which may occur due to radio wave conditions.
The aerial cable should not be bundled with the power cord and the like.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
This TV set provides 3 groups of AV input (including one group of DVD inputs) and 1 group of AV
out puts for your convenient connection to VTR, DVD or video camera to enjoy the high quality picture.
Please refer to the owner's manual of the equipment to be connected as well.
Using AV Inputs
!
Notes:
In AV1 inputs, the S-VIDEO terminal is prior to the VIDEO1 terminal. When both S-VIDEO and
video signals are input, the S-VIDEO signal is selected. To view a video sognal, disconnect the
S-VIDEO connection.
The AV2 inputs and the DVD inputs use the same audio terminals. When both DVD and video
signal are input, the DVD inputs are prior to VIDEO2 terminal and DVD signal is selected. To
view video signal, disconnect Y /CB /CR connection,
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
(continued)
Using DVD inputs
Using AV outputs
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning on/off
Turning on
Press the Power Switch on the
TV set.
The TV set is in STANDBY and the
1
Yellow indicator lights up.
2, 2
In STANDBY mode, press the button or 0-9 buttons
on the remote controller and the TV set is turned on.
2
3
In STANDBY mode, you can also press the
VOL
on.
, CH
or TV/AV button on the set to turn
Notes:
!
If there is no input signal, then a
blueback appears. After 15 minutes,
the set auto goes to STANDBY.
Turning off
Press the Power Switch on the TV set if you want to
1 cut off the power completely.
If you want to turn off the TV set temporarily,
press the button on the remote controller.
2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Select Input Signal
Watching AV program
To watch video program from AV input, PressTV/AV
button repeatedly until you see the appropriate input
indicator on the screen
1
Video1
Video2
Video3
10
!
Notes:
2
In AV1 inputs, the S-VIDEO terminal is prior to the VIDEO1
terminals. When both S-video and video signal are input, the S-
video signal is selected (the OSD is "S-VIDEO1"). To view a video
signal, disconnect the S-VIDEO connection.
The AV2 inputs and the DVD inputs use the same audio terminals.
When both DVD and video signal are input, the DVD inputs are
prior to VIDEO2 terminals and the DVD signal is selected (the OSD
is "DVD"). To view a video signal, diconnect Y/CB /CR connection.
4
1, 1
3
Switching from AV to TV
Press TV/TV button repeatedly until the TV program
appears.
1
2 Press digit buttons to switch back to TV mode.
Press CH+ or CH- button to switch back to TV mode.
3
button to switch back to TV mode.
4 Press
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuning in
To enter the SEARCH menu
Press MENU button.
1
2
Press VOL+ or VOL- button to
select SEARCH icon.
Press CH- button to disply
the Serach menu.
3
2, 2
Auto Search
Please enter the SEARCH menu first
Press CH+ or CH- button to
1 select AUTO MEMORY item.
1
1
Press VOL+ button to start
AUTO MEMORY.
2
2
2
All active channels will be preset and
stored into the memory automatically.
3
After presetting, the TV will stop at the
first channel program.
Notes:
!
During the process of AUTO MEMORY,
pressing the VOL- button will stop the
process and go to the first channel.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuning in
(continued)
Manual Search
Please enter the SEARCH menu first
Use MANUAL SEARCH function if desired
channels cannot be preset or if you would like to
preset channels to specific position numbers one
by one
Press CH+ or CH- button to select POSITION item.
1
Press VOL+ or VOL- buttons to select a channel
number (ranging from 000~255).
2
Press CH+ or CH- button to select SEARCH item.
3
Press VOL+ or VOL- button to start program search
manually.
4
Pressing VOL+, the set searches towards higher frequency;
Pressing VOL-, the set searches towaords lower frequency;
The search stops when a program is located and this program will be
stored in the specified position number.
1,3
1,3
2,4
2,4
!
Notes:
1.
You can use BAND selection to quicken search process if you know
which band your desired progam locates in. The band switches
amoung VHFL, VHFH and UHF.
2.
Repeat the above steps if you want to store another program in other
position numbers
To skip an unnecessary channel
Press CH+ or CH- button to select POSITION item.
1
Press VOL+ or VOL- button to select a channel
number, for example, channel 009.
2
3
4
Press CH+ or CH- button to select SKIP item.
Press VOL+ or VOL- button to
select ON.
Now channel 9 will be skipped when
you browse by CH+ or CH- button.
To restore a skipped channel, please select channel by step
1, 2 then repeat step 3 and 4 and set SKIP item to OFF.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Fine tuning
Please enter the SEARCH menu first
Fine tuning is not necessary under normal
conditions. However, in area of inferior
broadcast conditions where adjustment is
necessary for better picture and sound, use
Fine tuning.
Press CH+ or CH- button to select POSITION item.
1
Press VOL+ or VOL- buttons to select a channel number
you want to fine-tune (for example, channel 99).
2
Press CH+ or CH- button to select MFT item.
3
1,3
Press and hold VOL+ or VOL- button till the best
possible picture and sound are obtained.
4
2,4
Calling the on-screen display
You can call the on-screen display by pressing the DSP button on the
remote controlle. The first press of the DSP button display the current
state (if in TV mode, the current channel number will display) and the next
press display the clock time. Press this button again to cancel the OSD.
DSP
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel Selection
Using 0-9 direct channel selector
1
To select one-digit channel
There are 3 ways for you to select an one-digit channel number, for
example, channel 9 as follows.
After 2
seconds
Press "9"
button
9
9 - -
A
B
Press "0"
button
After 2
seconds
Press "9"
button
0 9 -
9
9
0 - -
Press "0"
button
Press "9"
button
Press "0"
button
0 0 -
C
0 - -
2
To select two-digit channel
There are 2 ways for you to select a two-digit channel number, for
example, channel 19 as follows
4
1, 1
3
Press "1"
button
After 2
seconds
Press "9"
button
1 9 -
19
A
B
1 - -
Press "0"
button
Press "9"
button
Press "1"
button
0 1 -
19
0 - -
To select three-digit channel
To select a three-digit channel number, for example, channel 199,
you just input the channel number on by one. Be sure that the
period of two-press channel should be within 2 seconds.
Press "1"
button
Press "9"
button
Press "9"
button
19 -
199
1 - -
Using CH+ or CH- button
Press CH+ button, the channel number increases;
Press CH- button, the channel number decreases.
2
3
Using previous channel
Press this button to switch between the current channel and previous
channel.
button
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Picture
Adjusting picture
Press MENU button.
1
2
Press VOL+ or VOL- button to
select PICTURE icon.
Press CH- button to disply
the PICTURE menu.
3
4
5
2, 2
Press CH+ or CH- button to select item.
Picture mode
Press VOL+ or VOL- button to adjust.
Picture mode
PERSONAL
Item
BRILLIANT STANDARD SOFTNESS
VOL -
VOL +
1
50
50
90
40
50
50
70
30
paler
deeper
Color
75
75
Brightness
darker
lighter
2,4
weaker
stronger
Contrast
100
50
2,5,3
6
Sharpness
softer
sharper
purplish
greenish
Tint
* Note: The item TINT is for NTSC only.
3
The adjusted setting are stored in the PERSONAL mode.
There are three preset picture modes and one user-set picture
mode. Press P.M button to select a picture mode according
to you favourites.
Press P.M button to select picture mode.
6
Setting blue background
Enter the PICTURE menu according to the above
1 steps 1-3.
Press CHL+ or CH- button to
select B.B item.
2
Press VOL+ or VOL- button to
select ON or OFF.
3
If the B.B item is set ON, the TV set will display a blue
background when there is no input signal.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Control
Adjusting volume
Use VOL+ or VOL- button.
1
Press VOL+ button, the volume increases;
Press VOL- button, the volume decreases.
Use MUTE button.
2
If you want to mute the sound, press
MUTE button on the remote.
To resume the sound, press this button
again.
!
Notes:
You can also resume the sound by pressing VOL+ or VOL- button.
1
Selecting sound mode
You can quickly select sound mode by
pressing S.M button.
2
NATURAL
THEATER
NEWS
S.M
MUSIC
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting WOOFER
Press MENU button.
1
Press VOL+ or VOL- buttons to
select SETTING icon.
2
Press CH- button to display
the SETTING menu.
3
4 Press CH+ or CH- button to select WOOFER item.
5 Press VOL+ or VOL- button to select ON or OFF.
Setting BALANCE
1
Enter the SETTING menu according to the above
steps 1-3.
4,2
1
2,5,3
Press CH+ or CH- button to
select BALANCE item.
2
3
Press VOL+ or VOL- button to
adjust.
3
Press VOL+ button, to decrease the left sound channel;
Press VOL- button, to decrease the right sound channel.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer Setting
To enter the TIMER menu
Press MENU button.
1
2
3
Press VOL+ or VOL- buttons to
select TIMER icon.
Press CH- button to display
the TIMER menu.
Setting CLOCK
Please enter the TIMER menu first.
Press CH+ or CH- button to select CLOCK item.
1
1
2,2
3
Press VOL+ or VOL- button to
set current time.
1
2
Setting sleep timer
You can quickly set the sleep timer by using the SLP button on the remote
controller. With every press of this button the sleep time changes as
follows;
SLP
120 Min.
110Min.
10 Min.
OFF
20 Min.
For example, you would like the TV to auto
turn off in 60 minutes, you can press the SLP
button repeatedly till the screen displays as
the right figure.
If you want to cancel the sleep timer, you can
press the SLP button repeatedly till "OFF"
displays on the screen.
SLEEP : 60MIN.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting OFF TIMER
Please enter the TIMER menu first.
Press CH+ or CH- button to select
OFF TIMER item.
1
2 Press VOL+ or VOL- button to select ONCE or EVERY.
Press CH- button.
3
4
Press VOL+ or VOL- button to set the OFF time, for
example 22:00.
The set auto turns off when the time is 22:00. If you set the OFF TIMER item
to ONCE, this function only effects once; If you set the OFF TIMER item to
EVERY, this function effects every day. To cancel this function, please set the
OFF TIMER to OFF.
1,3
1,3,5
!
Notes:
2,4
The Time can not be accessed until you set the Off Time to Once or Every.
2,4,6
Setting ON TIMER
Please enter the TIMER menu first.
Press CH+ or CH- button to select
ON TIMER item.
1
2 Press VOL+ or VOL- button to select ONCE or EVERY.
Press CH- button.
3
Press VOL+ or VOL- button to set the ON time, for example
18:00.
4
Press CH- button to selct POS item.
5
Press VOL+ or VOL- button to select a channel number, for
example, channel 10.
6
The set in STANDBY mode auto turns on and goes to channel 10 when the
time is 18:00. If you set the ON TIMER item to ONCE, this function effects only
once; If you set the ON TIMER item to EVERY, this function effect every day.
To cancel this function, set the ON TIMER to OFF.
!
Notes:
The Time can not be accessed until you set the ON TIMER to ONCE or EVERY.
When you are setting the time by VOL+/- button, if you press and release within
0.7 seconds, the time's increase or decrease step is 1 minute; if you press and hold
for more than 0.7 second, the time increase or decreas step is 10 minute.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setting
To enter the Setting menu
Press MENU button.
1
2
3
Press VOL+ or VOL- buttons to
select SETTING icon.
Press CH- button to display
the SETTING menu.
Selecting the OSD language
Please enter the SETTING menu first.
This TV set provides ENGLISH ans CHINESE (
) OSD language.
1 Press CH+ or CH- button to select LANGUAGE item.
2 Press VOL+ or VOL- button to select the OSD language.
1
1,3
2,2,4
3
Setting the colour and sound system
Please enter the SETTING menu first.
If the picture colour or sound is abnormal, maybe the colour and sonund
system setting is wrong. You can select a proper colour or sound system
as follows;
Press CH+ or CH- button to
1
select C.SYSTEM item.
Press VOL+ or VOL- button to
select a proper colour system.
2
3 Press CH+ or CH- button to select S.SYSTEM item.
Press VOL+ or VOL- button to select a proper sound
system.
4
Notes:
!
You can quickly set colour and sound system by
pressing the SYS button on the remote controller.
Please select item by CH+/- button and adjust by
VOL+/- button.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel Edit
This TV set enables you to edit the channel
programs.
Press EDIT button on the
remote controller.
1
2 Press CH+/- to select CHANNEL 1 item.
Press VOL+/- to select the first target channel.
3
Press CH+/- to select CHANNEL 2 item.
4
5 Press VOL+/- to select the second target channel.
Press CH+/- to select EXCHANGE item.
6
2,4,6
1
7 Press VOL+/- to exchange the two channel program.
3,5,7
To exchange more channels' programs, please repeat the above
steps.
Channel scanning
Press SCAN button on the remote
1
controller and the TV set begins program
scanning. All active channels will be
scanned on by one. After scanning, the
set stops at the orginal channel before
the program scanning begins. Press any
SCAN
button can stop the process of scanning
CHANNEL SCANNING
end the set stops at the current scanning
channel.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing BOX game
Please enter the OTHER menu first.
Press CH+ or CH- button to select
BOX item.
1
2 Press VOL+ or VOL- buttons to enter.
Button Introduction
Function
Button
Name
To transform the shape.
F1
To accelerate falling down.
To move the boxes.
F2
F3.
How to play?
1
Press any one of F1, F2 or F3 buttons to start the game.
1.
2.Press F1 to transform the shape; F2 to accelerate falling down; F3
to move the boxes.
2
3.When the boxes are placed fully in one row, this row will disappear
and the score increases 1 point. The score increases 3 points if two
rows of boxes disappear at the same time. Disappearing three
rows at the same time makes 7 points.
Game
control
buttons
4.
The right window indicates the nw=ext shape for your reference.
5.The game is over when the boxes are piled to the top of the window.
6.Pressing the GAME button can exit the game.
Playing GOBANG game
Please enter the OTHER menu first.
Press CH+ or CH- button to select
GOBANG item.
1
Press VOL+ or VOL- button to enter.
2
Button Introduction
: To move chessman
: To confirm your move
How to play?
In this game, you will play against the TV set. The part who firstly
connects a continuous five chessmen in horizontal, vertical or
diagonal direction wins the game.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
(continued)
Calendar setting
Please enter the OTHER menu first.
Calling
Switch
Press CH+ or CH- button to
1
select CALENDAR item.
Press VOL+ or VOL- buttons to
enter CALENDAR.
2
Pressing
month or date; Pressing
can adjust year, month or date.
or
button can select year,
or
button
Press any button except
to exit calendar.
,
,
or
1
Remote controller caller
This TV set provides RC (remote contrller)
calling function, which wil help you to find
the RC if you do not know where the RC is.
You just need to press the CALL button on
the set's side panel (the set should be in
STANDBY or working), the RC will play a
musical tone so that you can quickly get it.
When the set auto turns on through ON
TIMER function, the RC also plays a musical
tone to remind you. To active the above
functions, please turn the Calling Switch to
ON firstly (the Calling Switch is on the top
of the RC's left side).
2
Notes:
!
1. The RC will play a musical tone when you turn the Calling Switch to ON. If
you want to stop the music, please turn the Calling Switch to OFF and then
turn it ON quickly.
2. The RC consumes more power if the calling function is turned on, so we
recommend you to use high-capacity batteries. If you do not use the RC for
a long period of time, please turn off the calling function to avoid power
exhaustion.
3. If the Calling function is turned on and the RC is close to mobile phone
or other radiant equipment, the RC may be triggered and play the musical tone.
To stop the music, please follow step 1.
4. It is normal that some slight stripes appear on the screen when you
press CALL button on the set.
5. The top and middle position of the Calling Switch is ON and the bottom
position is OFF.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
To enter the OTHER menu
Press MENU button.
1
2
Press VOL+ or VOL- buttons to
select OTHER icon.
Press CH- button to display
the OTHER menu.
3
Notes:
!
1-9
digit
buttons
You can quickly access the OTHER menu by pressing GAME
button on the remote controller.
Playing HITTING game
Please enter the OTHER menu first.
1
Press CH+ or CH- button to select
HITTING item.
1
1
2,2
3
2 Press VOL+ or VOL- button to enter.
Function
Button
Name
Button Introduction
To start the game.
F1
To pause the game.
To exit the game.
F2
Game
control
buttons
How to play?
F3.
Press F1 button to start the game. The 1-9 digit buttons on the remote
controller match the 9 target boxes on the screen. Pressing any one of
these buttons can hit the relevant box, The score will be counted
according to the amount of the box hit within the stipulated time.
Playing SLOT game
Please enter the OTHER menu first.
Press CH+ or CH- button to select
SLOT item.
1
Press VOL+ or VOL- button to enter.
2
Function
Button
Name
Button
To start the game.
F1
Introduction
To pause the game or set rate.
To exit the game.
F2
F3.
How to play?
Before you start the game, you can set the rate by using F2. Press F1 button to start the game. Press F2 to
control the card (or set the rate). If you turn over 3 cards with the same value then you win the game, or you will
lose the game. If you want to exit the game, please press F2 to pause the game firstly before you press F3.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Before calling service personnel, please check the following chart for a possible cause to the trouble
you are experiencing.
Symptoms
Check the following items
Be sure the power cord is plugged in.
Contrast, colour, tint are not correctly adjusted
Power is not turned on
Poor colour, poor tint
Possible interferences of automobiles, motorcycle,
trolley bus, neon lamps, etc.
Spots appear on the screen
Possible interference of electronic interference
from another TV set, a computer, an electronics
game machine, a broadcast station, etc.
Stripes appear on the screen
Double images or "ghosts"
Snowy picture
This may be caused by reflections from nearby
mountains or buildings.
Check the antenna direction.
It is possible that the aerial "lead-in" is damaged or
comes off.
Check the antenna direction.
No Program menu page
and the maximum volume
is only 60.
Check whether the HOTEL mode is in LOCK status.
Even if the picture or the sound is normal, changes
in room temperature sometimes makes the TV
cabinet expand or contract, making a noise. This
does not indicate a malfunction.
TV cabinet creaks
The batteries may be worn out.
The batteries may be installed with their polarity
reversed.
Remote controller does
not work
When the set is switched on, do not shift or move
the set around. Sometimes it may develop an
unevenness in colour in some parts of the screen.
This can be eliminated by switching off the set with
the POWER switch and wait for 10 minutes before
switching on again.
Unevenness in colour in
some parts of the screen
The batteries power is insufficient, please replace
with high-capacity batteries.
Remote controller plays
music continually or
makes "Beep" sound
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power Supply:
Power Consumption:
Dimensions(mm):
Weight(kg):
AC 240V, 50Hz
140W
670(W) x 688(H) x 510(D)
43
CRT:
68cm
TV system & channel range
System
VHF
2-12
UHF
CATV
PAL-B/G
21-69
X~Z+2,S1~S41
Color System:
Sound output:
Accessories:
PAL-B/G NTSC playback
6W x 2
Remote controller X 1
!
Design and specifications are subject to change without notice.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL:(02)9313 7111
FAX:(02)9313 7555
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
604-K29183-01
Download from Www.Somanuals.com. All Manuals Search And Download.
|