Palsonic CRT Television 6125TS User Manual

OWNER'S MANUAL

61CM CORDLESS REMOTE COLOUR TELEVISION

MODEL: 6125TS

Type Tested

Electrical

Safety

AS/NZS 3250 Lic 4164

Standards Australia

APP No: N15959

PALSONIC CORPORATION PTY LTD

1 JOYNTON AVENUE

WATERLOO NSW 2017 AUSTRALIA

TEL: (02) 9313 7111

FAX: (02) 9313 7555

www.palsonic.com.au

PALSONIC CUSTOMER SERVICE

TELEPHONE

AUSTRALIA: 1300 657 888

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Features ........................................................................................................................

Important Safety Cautions ..........................................................................................

Identification of Controls ............................................................................................

Front view .................................................................................................................

Back view ..................................................................................................................

Remote control .........................................................................................................

Battery installation ...............................................................................................

Effective range of the remote ...............................................................................

Installation ....................................................................................................................

Connecting antenna ..................................................................................................

Connect to video and audio equipment ....................................................................

Operations ....................................................................................................................

Menu introduction .....................................................................................................

Turning on .................................................................................................................

Turning off .................................................................................................................

Presetting programs ..................................................................................................

Auto search ..........................................................................................................

Manual search .....................................................................................................

Fine Tuning ..........................................................................................................

Editing programs .......................................................................................................

Channel skipping .................................................................................................

Classifying Programs ...........................................................................................

Channel exchange/copy ......................................................................................

Setting Colour/Sound system ..............................................................................

Selecting channel/input signal ..................................................................................

Selecting channel ................................................................................................

Selecting external input signal .............................................................................

Adjusting the picture/sound ......................................................................................

Clock setting .............................................................................................................

Current time setting .............................................................................................

Off timer setting ...................................................................................................

On timer setting ...................................................................................................

Setting channel timer ...........................................................................................

System setting ..........................................................................................................

Background ..........................................................................................................

Colour/sound system ...........................................................................................

Other function introduction .......................................................................................

Troubleshooting Guide ...............................................................................................

Specifications ..............................................................................................................

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

USOC and Intellectualized I²C-bus control

Five picture modes

Two groups of Video/Audio input terminal

One S-VIDEO termial

One group of DVD (Y, Cr, Cb) input terminals

Audio/Video output terminals

Program exchange/Program copy

Game/Calendar

Child lock function

200 channels

Music TV function

Noise reduction

Image enhancing

Channel scanning

Programs classified

Screen protecting function

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Safety Cautions

When any unusual situation occurs, turn off the

power supply at once and remove the plug from the

wall outlet. Contact a qualified service department in

your local area.

Do not expose the TV set to rain or excessive

moisture. Avoid using the set in very warm or

damp places and never use it in a bathroom.

When cleaning dust off the picture tube disconnect

the power first. You can wipe lightly with a piece of

dry, clean and soft cloth.

Avoid exposing the set to direct sunlight and other

sources of heat to prevent damage to the cabinet

and components.

High voltage exists in this TV set. Do not remove the

cover.

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Safety Cautions

When any unusual situation occurs, turn off the

power supply at once and remove the plug from the

wall outlet. Contact a qualified service department in

your local area.

Do not expose the TV set to rain or excessive

moisture. Avoid using the set in very warm or

damp places and never use it in a bathroom.

When cleaning dust off the picture tube disconnect

the power first. You can wipe lightly with a piece of

dry, clean and soft cloth.

Avoid exposing the set to direct sunlight and other

sources of heat to prevent damage to the cabinet

and components.

High voltage exists in this TV set. Do not remove the

cover.

Download from Www.Somanuals.com. All Manuals Search And Download.

This TV set can operate on a power of ~240V, 50Hz. You must not use a power

supply of any other type.

Do not cover the ventilating hole in the cabinet

Keep a space of more than 10cm from the walls to the

TV set to ensure adequate ventilation.

If the power cord or the plug is damaged contact a

qualified service department for service.

When the TV set is to be left unattended for a long

period of time, turn off the power supply and remove

the plug from the wall outlet.

Don't try to push anything into the cabinet or place

any vessel with water on the TV set.

Don't overload wall outlets; extension cords, or

integral convenience receptacles as this can result

in a risk of fire or electric shock.

Auto degaussing:

When you remove the TV set to another place or when other electronic machines near the set are

working, the colour TV set will be magnetised. The colour of the TV will be abnormal and the colour

points appear on the screen. To avoid the bad effect, an auto degaussing circuit is designed. When

the TV set is magnetised you should cut off the power to the set for at least 30 minutes to assure the

auto degaussing circuit woks well.

Download from Www.Somanuals.com. All Manuals Search And Download.

Identification of Controls

Front view

AV/TV

VOL-

VOL+

CH-

CH+

1. Power Switch.

2. Remote Sensor.

3. Indicator.

4. AV/TV button: Video input select.

5. MENU button: To enter into menu operation.

6. VOL- button: volume down adjust; menu item adjust.

7. VOL+ button: volume up adjust; menu item adjust.

8. CH- button: channel down select; menu item select.

9. CH+ button: channel select; menu item select.

Download from Www.Somanuals.com. All Manuals Search And Download.

Back view

(2)

L/MONO

VIDEO

(1)

DVD

VIDEO

S-VIDEO

AUDIO

1. Antenna input

2. AV Output (VIDEO, AUDIO L, R)

3. AV1 input (VIDEO, AUDIO L, R)

4. AV output (VIDEO, AUDIO L, R)

5. S-VIDEO input

6. AV2 input (VIDEO, AUDIO L, R)

Download from Www.Somanuals.com. All Manuals Search And Download.

Identification of Controls

(continued)

Remote control

Power on/standby

Sound Mute

Direct Channel select

PRESET

SLEEP

To display PRESET menu

Sleep timer

Previous channel

TV/VIDEO Input select

Channel up/menu item select

To access MENU operation

On-screen display call

Volume up/menu item adjust

PIC

DSP

To display the PICTURE menu

Volume down/menu item adjust

VOL

Picture mode select

This button has no

function on this model

S-MODE

Channel down/menu item select

Sound system select

Select program type group

TYPE SELECT C-SYS

MUSIC GAME

S-SYS

Colour system select

Playing game

Select the program in a group

To enter into music TV mode

Download from Www.Somanuals.com. All Manuals Search And Download.

Battery Installation

Please install the batteries before using the remote control.

Install two "AA" batteries

Replace the battery cover.

Open the battery cover.

matching the +/- polarities

of the battery to the +/-

marks inside the battery

compartment.

Effective range of the remote control

Notes:

1. There should be no obstacle between the TV

and the transmitter.

2. Use the remote control within the effective range

as the above figure.

3. If the remote control does not work, please check

whether the batteries are exhausted or the

polarity is wrong.

4. When direct sunlight, and incandescent lamp,

fluorescent lamp or any other strong light shines

on the remote sensor of the TV, the remote

operation may be unstable.

6. When the remote control will not be used for a

long period of time or when the batteries are

worn out, remove the batteries.

6. Do not drop or dampen the remote control.

7. Do not disassemble the remote control.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Connecting antenna

Optimum reception of colour requires a good signal and will generally mean that an outdoor antenna

must be used. The exact type and position of the antenna will depend upon your particular area.

Notes:

Turn off the power first, when you connect an outdoor antenna to the antenna input

terminal. When installing an outside antenna system, extreme care should be taken

to keep from touching power lines or circuits as contact with them might be fatal. In

thunder and lighting weather, please disconnect the outdoor antenna to avoid

thunder/lightning strike.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting video and audio equipment

This TV set provides 2 groups of AV input terminals (including 1 group of DVD and

S-Video input terminals) for your convenient connection to VCR, DVD or other video

equipment to enjoy the high quality picture.

Please refer to the owner's manual of the equipment to be connected as well.

Connecting the rear AV input terminals.

To audio

outputs

Video equipment

without S-video

terminal

To video

output

To Y output

To Cr output

To Audio R output

To Audio L output

Yellow (video)

White (audio L)

R Red (audio R, CR)

Green (Y)

(1)

DVD

Blue (CB)

VIDEO

S-VIDEO

AUDIO

Video equipment

with S-video

terminal

To S-VIDEO

output

To audio outputs

Notes:

The S-VIDEO input terminal has priority over AV1 VIDEO terminal. The DVD terminal has priority

over S-VIDEO input terminal. If you want to use equipment connect to S-VIDEO terminal, please

disconnect any plug from DVD terminal. If you want to use equipment connect to AV1 VIDEO terminal,

please disconnect any plug from DVD and S-VIDEO terminal.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the side AV input terminals

(2)

VIDEO EQUIPMENT

L/MONO

VIDEO

To video output

To audio outputs

Signal

Connecting the AV output terminals

(1)

DVD

VCR

VIDEO

S-VIDEO

AUDIO

Audio Amplifier

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Menu Introduction

Press the MENU button repeatedly to select the screen display as below. In menu

operation, press CH+/- to select item, press VOL+/- to adjust selected item.

The SYSTEM1 menu

The PICTURE menu

BRIGHTNESS

CONTRAST

COLOR

SHARPNESS

TINT

COLOR SYS

SOUND SYS

BACKGROUND

PROGRAM

EXCHANGE

COPY

AUTO

007

---

SEL

ADJ

SEL

ADJ

The PRESET menu

(TV mode only)

The SYSTEM2 menu

PROGRAM

TYPE

008

IMAGE ENHANCE

CALENDAR

GAME

USER2

V-H

BAND

SKIP

OFF

FINE TUNE

MANUAL SEARCH

AUTO SEARCH

SEL

ADJ

SEL

ADJ

The CLOCK menu

TIME

--:--

---

OFF-TIME

ON-TIME

CH-TIME

PROGRAM

SEL

ADJ

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Turning On/Turning Off

Turning On

Press the MAIN POWER SWITCH to turn on the TV set.

If the TV set is in STANDBY mode. Press

the remote control, then the TV set is turned on.

, CH+/- or 0-9 buttons (one digit only) on

When the remote control is not at your hand, you can also press the CH+/- buttons on

the TV set to turn on the TV.

Note:

If there is no input signal to the TV when the TV is on, blue background will appear on

the screen (when the BACKGROUND is set to ON). After 10 minutes if there are still

no TV signals to the TV, it will access standby mode automatically.

Turning Off

1 ^{Press the MAIN POWER SWITCH on the TV set if you want to cut off the power}

completely.

If you want to turn off the TV set temporarily, press the button

control and the TV is in STANDBY mode.

on the remote

Notes:

There are three kinds of Auto-Power-off function:

1. When there is no input signal for 10 minutes.

2. Sleep-timer function.

3. Off-timer function.

In the AV mode, this Auto-Power-Off function does not work.

Last-Mode-Memory:

When you turn off the set, the last TV mode, picture/sound setting and preset

channels all are memorised, Therefore, next time you turn on the TV, the TV will

work in the previous setting mode.

If you directly pressed the main power switch on the TV set to turn it off, you can

press the main power switch to turn on the TV set.

If you press the main power switch to turn off the when in standby mode, you

must do as turning on-2 to turn on the TV.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Presetting programs

Firstly, use the Auto search function to preset all active channels in your area automatically.

Then arrange the preset channels with the manual search and program edit functions.

Auto Search

Press the MENU button to select PRESET menu.

Press CH+/- to select AUTO SEARCH.

PROGRAM

TYPE

008

USER2

V-H

BAND

Press VOL+/- and the TV set starts Auto channel preset. All

active channels will be preset and stored into the memory

automatically. After presetting, the TV will display the first channel.

SKIP

OFF

FINE TUNE

MANUAL SEARCH

AUTO SEARCH

SEL

ADJ

During the process of Auto channel preset, pressing the MENU

button will stop the process.

Note: Before you start Auto Search, we recommend you to

set a proper Sound system and Colour system according to

your local area.

Manual Search

If desired channel can not be preset by Auto search or if you

would like to preset channels to specific position numbers one

by one, use manual search function.

Access the PRESET menu, then select PROGRAM item by

CH+/- and set the desired channel number (from 0~199) by

VOL+/- or Digit buttons.

PROGRAM

TYPE

008

USER2

V-H

BAND

SKIP

OFF

FINE TUNE

MANUAL SEARCH

AUTO SEARCH

Press CH+/- to select MANUAL SEARCH item. Press VOL+

button, the set searches towards higher frequency. Press

VOL- button, the set searches towards lower frequency.

The search stops when a program is found and this program

will be stored in the specified position number.

SEL

ADJ

You can use band selection to quicken search process. Select

BAND item and press VOL+/- buttons. The band switches

among V-L, V-H and UHF. Then select MANUAL SEARCH

item and press VOL+/- buttons to start manual search.

PROGRAM

TYPE

008

USER2

V-H

BAND

SKIP

OFF

FINE TUNE

MANUAL SEARCH

AUTO SEARCH

Repeat the above steps if you want to store another program

in other position number.

SEL

ADJ

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Presetting programs (continued)

Fine Tuning

When picture and sound's effect of a channel is poor (for

example: one or two CATV channel's picture and sound

are not standard), you can correct them by making use of

Fine tuning.

PROGRAM

TYPE

008

USER2

V-H

BAND

SKIP

OFF

FINE TUNE

MANUAL SEARCH

AUTO SEARCH

Access the PRESET menu, then select PROGRAM item by

CH+/- and set the desired channel number (from 0~199) by

VOL+/- or Digit buttons.

SEL

ADJ

In the menu, select FINE TUNE item, then press and hold

VOL+/- buttons until the best picture and sound are obtained.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Editing programs

Channel skipping

After presetting the channels, you can skip unnecessary

position numbers so that only the channels you want are

selected.

PROGRAM

TYPE

008

USER2

V-H

Access the PRESET menu, then select PROGRAM item by

CH+/- and set the desired channel number (from 0~199) by

VOL+/- or Digit buttons.

BAND

SKIP

OFF

FINE TUNE

MANUAL SEARCH

AUTO SEARCH

SEL

ADJ

In the menu, please select SKIP item and press VOL+/-

buttons to select ON.

Now the selected channel will be skipped when you browse

channels by CH+/- buttons.

PROGRAM

TYPE

008

USER2

V-H

If the SKIP is set to ON, when you select the channel by Digit

buttons, the program number displayed on the screen is purple

and a " * " symbol can be seen.

BAND

SKIP

FINE TUNE

MANUAL SEARCH

AUTO SEARCH

SEL

ADJ

To restore a skipped channel, please select the skipped

channel number by digit buttons. Then enter into the PRESET

menu to select SKIP item and set it to OFF.

Classifying programs

You can classify the programs as six types: USER1, USER2,

NEWS, SPORTS, MOVIE, TELEPLAY. The function

can help you select program more rapidly.

PROGRAM

TYPE

008

USER2

V-H

BAND

SKIP

Access the PRESET menu, then select the program number.

Press CH+/- buttons to select TYPE item. Press VOL+/- buttons

to select the program type.

FINE TUNE

MANUAL SEARCH

AUTO SEARCH

SEL

ADJ

The program types are defined by yourself. The USER1 and

USER2 types can be used to store the programs that the user

often watches or is interested in.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Editing programs (continued)

Channel exchange/copy

After channel presetting, you can edit the programs by

using the channel exchange and channel copy functions.

COLOUR SYS

SOUND SYS

BACKGROUND

PROGRAM

EXCHANGE

COPY

AUTO

007

---

Press MENU button repeatedly to access the SYSTEM1 menu.

Select PROGRAM item and select a channel number A

by Digit buttons.

---

SEL

ADJ

Select EXCHANGE item and press Digit buttons to set

another channel number B that you would like to exchange

with the program number which is displayed in the

PROGRAM item. Then press VOL+/- buttons to confirm.

COLOUR SYS

SOUND SYS

BACKGROUND

PROGRAM

EXCHANGE

COPY

AUTO

007

008

---

SEL

ADJ

Now the programs of the two channels are exchanged.

COLOUR SYS

SOUND SYS

BACKGROUND

PROGRAM

EXCHANGE

COPY

AUTO

007

---

008

Select COPY item and press Digit buttons to select a

channel number C. Then press VOL+/- buttons to confirm.

Now the program in channel A will be copied to channel C.

SEL

ADJ

Setting colour/sound system

If the picture's colour or sound is abnormal, you can

adjust colour or sound system as follows.

Press C-SYS button repeatedly and the colour system will

be switched between AUTO, PAL, N3.58 and N4.43. You

can select a proper colour system.

AUTO

B/G

Press S-SYS button can select sound system. In this model,

the sound system is B/G and there is no need to adjust it.

When you press C-SYS or S-SYS button, the screen

displays as shown on the right.

You can also access the SYSTEM1 menu which is shown

on the right and adjust the COLOR SYS item and the

SOUND SYS item to set the colour system and the

sound system.

COLOUR SYS

SOUND SYS

BACKGROUND

PROGRAM

EXCHANGE

COPY

AUTO

007

---

SEL

ADJ

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Selecting Channel/input signal

Selecting channel

Use Digit buttons

To select one-digit channel

Press --/-- button to

display "-".

Press 0-9 direct

channel selector.

To select two-digit channel

Press --/-- button

repeatedly to

display "--".

Press 0-9 buttons.

Press 1-9 buttons.

To select three-digit channel

1- -

168

Press --/-- button

repeatedly to

display "1--"

Press 0-9 buttons.

Note: The maximum channel number is 199, the set does not act if the

channel number you input is out of the range of 0~199.

Use CH+/- buttons

Press CH+ button, the channel number increases;

Press CH- button, the channel number decreases.

3 _{Use previous channel}

button

Press

button to switch between the current channel and previous channel.

4 ^{Use TYPE and SELECT buttons}

Press TYPE button to select the program type group that you want to watch.

Press SELECT button repeatedly, and the program is switched among the type group.

Selecting the external Input Signal

Press AV button repeatedly, the screen displays input signal source

AV1 (S-VIDEO, DVD) or AV2. Select the input signal source you need.

2 _{To return to TV mode, you can press AV button or 0-9 buttons.}

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Adjusting the picture/sound

Adjusting the picture

Using the PP button:

You can press PP button to select the desired picture mode: MILD, STANDARD,

NATURE, CUSTOM, COLORFUL.

Picture quality

Mode

MILD

Soft and moody picture

Standard picture

STANDARD

NATURE

COLOURFUL

CUSTOM

NATURE

CUSTOM

COLORFUL

MILD

Normal picture

Bright and dynamic picture

The picture quality you set

STANDARD

Using the PICTURE menu:

Press MENU button or PIC button to access the PICTURE menu.

Press PIC button repeatedly or press CH+/- buttons to select item upwards or

downwards.

Press VOL+/- buttons to adjust selected item.

Item

CONTRAST

BRIGHT

COLOR

SHARPNESS

TINT

VOL-

weaker

darker

paler

softer

purplish

VOL+

stronger

lighter

deeper

sharper

greenish

Notes:

1 .The item TINT is for NTSC only.

2. The above parameters maybe different in different models.

Adjusting the sound

1 ^{Use VOL+/- buttons}

Press VOL+ button to increase the volume.

Press VOL- button to decrease the volume.

Use

Press

button

button to mute the sound completely and the screen displays

button again to restore and the VOLUME bar appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Clock Setting

Press MENU button repeatedly to access

the CLOCK menu.

Current time setting

Select TIME item.

TIME

14:03

--:--

---

Press VOL- button to set the hour (0~23).

Press VOL+ button to set the minute (0~59).

OFF-TIME

ON-TIME

CH-TIME

PROGRAME

Note: The ON-TIME and OFF-TIME can be set

SEL

ADJ

only after you finish setting the TIME item.

Off timer setting

Select OFF-TIME item.

Set the OFF time. Press VOL- to set the hour (0~23).

Press VOL+ to set the minute (0~59).

TIME

14:03

14:07

15:30

--:--

OFF-TIME

ON-TIME

CH-TIME

PROGRAM

The TV set in working mode goes to STANDBY mode

automatically when the OFF time elapses.

---

SEL

ADJ

On timer setting

Select ON-TIME item.

Set the ON time. Press VOL- to set the hour (0~23).

Press VOL+ to set the minute (0~59)

TIME

14:03

14:07

15:30

--:--

---

OFF-TIME

ON-TIME

CH-TIME

PROGRAM

In STANDBY mode, the TV set auto turns on when

your preset ON time elapses.

SEL

ADJ

Notes: Once the function of ON-TIME or OFF-TIME fulfil, you need to set the

ON-TIME or OFF-TIME again if you want to use this function next time

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Clock Setting

Setting channel timer

Select CH-TIME item.

Set the CH-TIME. Press VOL- to set hour (0-23) Press VOL+

to set minute (0~59).

TIME

14:02

14:07

15:30

16:21

---

OFF-TIME

ON-TIME

CH-TIME

PROGRAM

SEL

ADJ

Select PROGRAM item. Set the channel number by Digit or

VOL+/- buttons.

TIME

14:02

14:07

15:30

16:21

008

OFF-TIME

ON-TIME

CH-TIME

PROGRAM

SEL

ADJ

The TV set will switch to the preset channel when the CH-TIME

elapses.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

System Setting

Background Setting

With the background function ON, when no signal is being

received, a preset background and customer's logo will appear.

COLOR SYS

SOUND SYS

BACKGROUND

PROGRAM

EXCHANGE

COPY

AUTO

B/G

007

---

Access the SYSTEM1 menu. Press CH+/- buttons to select

BACKGROUND item.

---

SEL

ADJ

Press VOL+/- buttons to select ON or OFF.

Colour/sound system setting

COLOR SYS

SOUND SYS

BACKGROUND

PROGRAM

EXCHANGE

COPY

AUTO

B/G

007

---

Press C-SYS or S-SYS button on the remote control

repeatedly to set colour system or sound system.

---

You can also access the SYSTEM1 menu. Press CH+/- to

select COLOR SYS item or SOUND SYS item.

SEL

ADJ

Press VOL+/- buttons to select colour system or sound

system.

COLOR SYS

SOUND SYS

BACKGROUND

PROGRAM

EXCHANGE

COPY

AUTO

B/G

007

---

SEL

ADJ

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Other functions introduction

Game introduction

There is a built-in game (Box man) for you to play.

Press GAME button to access game interface.

Description of icons:

:the man you control.

:the box to push.

:the destination to push the box to.

:the wall.

STAGE: 1

STEP: 000

On the screen, press PP button select STAGE, then you can start game.

The player should control the man to push the box just push, not pull) to the destination within the

wall by using CH+, CH-, VOL+, VOL- buttons.

Press GAME button to exit game, if you want to play again then press GAME button again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Other function introduction

Image Enhance setting

With built-in image enhance circuit you can use the function to

improve the visibility of details near black.

Access the SYSTEM2 menu. Press CH+/- buttons to select

IMAGE ENHANCE item.

IMAGE ENHANCE

CALENDAR

GAME

Press VOL+/- buttons to select ON, the image enhance is

available.

SEL

ADJ

Noise Reduction setting

IMAGE ENHANCE

If the signal being received is weak and the picture is blurry,

active this function to improve the picture quality.

Access the SYSTEM2 menu. Press CH+/- buttons to select

NR item.

CALENDAR

GAME

SEL

ADJ

Press VOL+/- buttons to select ON.

Calendar

IMAGE ENHANCE

Access the SYSTEM2 menu. Press CH+/- buttons to select

CALENDAR item.

CALENDAR

GAME

Press VOL+/- buttons to access calendar interface.

SEL

ADJ

Press CH+/- buttons to change the year. Press VOL+/- buttons

to change the month.

The calendar is from 1990 to 2089.

10-2002

SU MO TU WE TH FR SA

15 16

22 23

29 30

13 14

20 21

27 28

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Other functions introduction

Setting music TV function

If you only want to listen to the music, you can press MUSIC

button and the screen displays MUSIC TV. Five seconds later, the

screen is blank while the sound is normal. Press any button on the

remote control to exit MUSIC mode.

MUSIC TV

Sleep timer

Press SLEEP button repeatedly to set sleep time from 15

minutes to 120 minutes.

When the sleep time elapses, the TV set goes to STANDBY

mode automatically.

If you want to cancel Sleep timer, press and hold SLEEP button

until the screen displays the icon

Child lock

Press and hold MUSIC button until the screen displays a lock

icon. Now the TV set is in Child lock state. The screen is blue

and most of the buttons are useless.

If you want to resume, press and hold MUSIC button again until

the lock icon disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

Before calling service personnel, please check the following chart for a possible

cause to the trouble you are experiencing.

Symptoms

Check the following items

Be sure the power cord is plugged in.

Power is not turned on.

Poor colour, poor tint.

Contrast, colour, tint are not correctly adjusted.

Possible interferences of automobiles, motorcycle,

trolley bus, neon lamps, etc.

Spots appear on the screen.

Possible interference of electronic interference

from another TV set, a computer, an electronics

game machine, a broadcast station, etc.

Stripes appear on the screen.

Double images or "ghosts".

Snowy picture.

This may be caused by reflections from nearby

mountains or buildings.

Check the antenna direction.

It is possible that the aerial "lead-in" is damaged or

comes off.

Check the antenna direction.

The batteries may be worn out.

The batteries may be installed with their polarity

reversed.

Remote controller does

not work.

Even if the picture or the sound is normal, changes

in room temperature sometimes makes the TV

cabinet expand or contract, making a noise. This

does not indicate a malfunction.

TV cabinet creaks.

When the set is switched on, do not shift or move

the set around. Sometimes it may develop an

unevenness in colour in some parts of the screen.

This can be eliminated by switching off the set with

the POWER switch and wait for 10 minutes before

switching on again.

Unevenness in colour in

some parts of the screen.

No picture and most of the

buttons are useless.

It is possible that the TV set is in child lock mode.

It is possible that the TV set is in music TV mode.

Black screen but the sound

is normal.

AV playback interference.

It is possible that both of the DVD and S-Video

terminals are connected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Power Supply:

Power Consumption:

Dimensions (mm):

Weight (kg):

AC 240V, 50Hz

140W

700(W) x 510(H) x 481(D)

CRT:

61cm

TV system & channel range

System

VHF

2-12

UHF

CATV

PAL-B/G

21-69

X~Z+2,S1~S41

System:

PAL, NTSC (AV)

2 x 4W

Sound output:

Accessories:

Remote controller X 1

Design and specifications are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

PALSONIC CORPORATION PTY LTD

1 JOYNTON AVENUE

WATERLOO NSW 2017 AUSTRALIA

TEL: (02) 9313 7111

FAX: (02) 9313 7555

www.palsonic.com.au

PALSONIC CUSTOMER SERVICE

TELEPHONE

AUSTRALIA: 1300 657 888

604-TS25533-01

Ver 1.0

Download from Www.Somanuals.com. All Manuals Search And Download.

Miller Electric Welder 500D User Manual
Multiquip Automobile Parts MQD2H User Manual
Napoleon Grills Gas Grill 450 User Manual
Navionics Network Router 87043_1 User Manual
NeumannBerlin Microphone KMS 140 User Manual
Nilfisk ALTO Vacuum Cleaner Sweeper PS 27 User Manual
Nissan Automobile 2009 Altima User Manual
Omega Computer Hardware OMB DAQBOARD 500 User Manual
Oregon Scientific Speaker IB368 User Manual
Panasonic Telephone KXTG6311 User Manual