Packard Bell
EasyNote GN45
Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Overview
This document contains step-by-step disassembly instructions for the Packard Bell EasyNote GN45. The
instructions are illustrated where necessary with images of the part that is being removed or
disassembled.
Packard Bell reserves the right to make changes to the EasyNote GN45 without notice.
Technician Notes
Only technicians authorized by Packard Bell B.V. should attempt to repair this equipment. All
troubleshooting and repair procedures are detailed to allow only subassembly/module level repair.
Because of the complexity of the individual boards and subassemblies, no one should attempt to make
repairs at the component level or to make modifications to any printed wiring board. Improper repairs can
create a safety hazard. Any indication of component replacement or printed wiring board modifications
may void any warranty or exchange allowances.
Disassembly Instructions
When disassembling the system unit, follow these general rules:
„
„
„
„
Turn off the power using the battery switch.
Disconnect the adapter.
Remove the SD or MMC card from the device.
Do not disassemble the system into parts that are smaller than those specified in the
instructions.
„
Label all removed connectors; note where the connector goes and in what position it was
installed.
Reassembly Instructions
Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws are
returned to their proper positions. Check that no tools or any loose parts have been left inside the casing.
Check that everything is properly installed and tightened.
Required Tools
All disassembly procedures can be performed using the following tools:
„
Small Phillips and flat blade screwdriver.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3
WARNING
Hazardous Voltage
Ensure that the notebook is disconnected
from its power source and from all
telecommunications links, networks, or
modem lines whenever the casing cover is
removed. Do not operate the notebook with
the cover removed.
There is hazardous voltage present inside the
notebook when it is connected to an AC supply, even
when the notebook’s power switch is off. Exposure to
hazardous voltage could cause personal injury. To
avoid risk of injury, contact an Authorized Service
Provider for proper (un)installation of optional
hardware devices.
AVERTISSEMENT
Assurez-vous que le système est
débranché de son alimentation ainsi que de
toutes les liaisons de télécommunication,
des réseaux, et des lignes de modem avant
d’enlever le capot. Ne pas utiliser le
système quand le capot est enlevé.
Avoid Electrostatic Discharge
Electrostatic electricity can easily damage circuit cards
and integrated circuits (ICs). To reduce risk of
damage, store them in protective packaging whenever
they are not installed in your system.
WARNUNG
Das System darf weder an eine
Stromquelle angeschlossen sein noch eine
Verbindung mit einer
Telekommunikationseinrichtung, einem
Netzwerk oder einer Modem-Leitung haben,
wenn die Gehäuseabdeckung entfernt wird.
Nehmen Sie das System nicht ohne die
Abdeckung in Betrieb.
Add-in cards can be extremely sensitive to ESD and
always require careful handling. After removing the
card from the notebook, place the card flat on a
grounded, static-free surface, component-side up. Use
a conductive foam pad if available, but not the card
wrapper. Do not slide the card over any surface.
Before you install or remove memory modules, video
memory, disk drives, circuit cards or other devices,
protect them from static electricity. To do so, make
sure your notebook’s power switch is OFF. Then,
unplug the notebook’s AC power cord. Before picking
up the device you (un)install, you should wear an anti-
static wrist wrap (available at electronic supply stores).
Be sure to connect the wrist wrap to an unpainted
metal portion of the notebook casing. As an
alternative, you can dissipate electrostatic build-up by
touching an unpainted metal portion of the notebook
casing with one hand. Then touch the device you are
(un)installing with the other hand, and maintain
continuous contact with it until it is (un)installed in the
notebook.
ADVERTENCIA
Asegúrese de que cada vez que se quite la
cubierta del portátil, el sistema haya sido
desconectado de la red de alimentación y
de todos lo enlaces de telecomunicaciones,
de red y de líneas de módem. No ponga en
funcionamiento el sistema mientras la
cubierta esté quitada.
WAARSCHUWING
Zorg er voor dat alle verbindingen van en
naar de notebook (stroom, modem,
netwerk, etc) verbroken worden voordat de
behuizing geopend wordt. Zet de notebook
nooit aan als de behuizing geopend is.
Power Supply Unit
AVVERTENZA
Under no circumstances should you attempt to
disassemble the power supply. The power supply
contains no user-serviceable parts. Inside the power
supply are hazardous voltages that can cause serious
personal injury. Always return a defective power
supply to your dealer.
Prima di rimuovere il coperchio del telaio,
assicurarsi che il sistema sia scollegato
dall’alimentazione, da tutti i collegamenti di
comunicazione, reti o linee di modem. Non
avviare il sistema senza aver prima messo
a posto il coperchio.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Battery
Perform the following steps to remove the battery:
1. Make sure the power is off.
2. Turn the unit upside down.
3. Unlock the left battery lock.
4. Push battery lock on right outward to the release the battery.
5. Slide the battery out of its place in the direction of the arrow.
Fig. 1 Removing the battery.
Hard Disk Drive
To remove the hard disk drive, first remove the battery (see Battery) and then perform the following steps:
1. Remove the screws on the hard disk drive cover and carefully open it.
Fig. 2 Removing the hard disk drive cover.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5
2. Pull out the hard disk drive using the plastic tab.
Fig. 3 Removing the hard disk drive.
3. Remove the two screws on both sides of the hard disk drive shield.
Fig. 4 Unscrewing the hard disk drive shield screws.
Optical Disk Drive
To remove the optical disk drive, first remove the battery (see Battery) and then perform the following
steps:
1. Release the screw securing the optical disk drive.
Fig. 5 Releasing the optical disk drive.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6
2. Remove the optical disk drive from the drive bay.
Fig. 6 Removing the optical drive.
Memory Module
To remove the memory module, first remove the battery (see Battery) and then perform the following
steps:
1. Release the screws retaining the memory module slot cover.
Fig. 7 Removing the memory slot cover.
2. Remove the memory module from the slot and put it aside.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Fig. 8 Removing the memory module.
WLAN Card
To remove the WLAN card, first remove the battery (see Battery) and then perform the following steps:
1. Release the screws retaining the memory module slot cover (see step 1 in Memory Module).
2. Disconnect the wireless antenna cables (red circles on Fig. 9).
Fig. 9 Removing the WLAN card.
3. Remove the two screws securing the WLAN card (yellow circles on Fig. 9).
4. Lift the card from the main board.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Keyboard
To remove the keyboard, first remove the battery (see Battery) and then perform the following steps:
1. Remove the indicated screws on the back of the notebook.
Fig. 10 Left keyboard back screw.
Fig. 11 Right keyboard back screw.
2. Use a small screwdriver to unlock the keyboard cover on both sides.
Fig. 12 Releasing the keyboard cover.
3. Remove both screws securing the keyboard.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Fig. 13 Releasing the keyboard.
4. Before removing the keyboard, disconnect the keyboard flat cable.
Fig. 14 Disconnecting the flat cable.
Top Cover
To remove the top cover, first remove the battery (see Battery), remove the hard disk drive (see Hard
Disk Drive), remove the optical disk drive (see Optical Disk Drive), remove the keyboard cover (see
Keyboard), Remove the Express Card (if needed), and then perform the following steps:
1. Turn the notebook upside down and remove all screws securing the bottom cover.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Fig. 15 Removing the bottom cover screws.
2. Remove the four screws securing the top cover to the motherboard.
Fig. 16 Releasing the top cover.
3. Separate the top cover from the casing.
LCD Module
To remove the LCD module, remove the keyboard top cover (see Keyboard) and then perform the
following steps:
1. Remove the four screws holding the LCD module
2. To disconnect the video cable, carefully pull the plastic part upward.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Fig. 17 Removing the LCD module.
LCD Panel
To remove the LCD panel, remove the keyboard cover (see Keyboard) and then perform the following
steps:
1. Remove the screw securing the LCD cover next to the hinge on each side.
Fig. 18 Removing the LCD cover screws.
2. Remove the LCD top cover.
Fig. 19 Removing the LCD cover.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
12
3. Disconnect the VGA cable.
Fig. 20 Disconnecting the VGA cable.
Main Board
To remove the main board, first remove the top cover (see Top Cover) and then perform the following
steps:
1. Remove the four screws securing the main board.
Fig. 21 Removing the main board screws.
2. Pull the main board towards the right side and upward to extract it from the casing.
CPU
To remove the CPU, first remove the main board (see Main Board) and then perform the following steps:
1. Remove the screws securing the heat sink.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Fig. 22 Removing the heat sink.
2. Remove the CPU.
Fig. 23 Removing the CPU.
Express Card Reader
To remove the Express Card reader, remove the top cover (see Top Cover) and then do the following:
1. Remove the two screws securing the Express Card reader.
Fig. 24 Express card reader slot.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Touchpad
To remove the touchpad, first remove the top cover (see Top Cover) and then perform the following
steps:
1. Remove the four screws securing the touchpad to the top cover.
Fig. 25 Removing the touchpad.
Speaker Assembly
To remove the speaker assembly, first remove the top cover (see Top Cover) and then perform the
following steps:
1. Remove the two screws holding the speaker assembly.
Fig. 26 Removing the speaker assembly.
Power Button / WiFi / ECO Card
To remove the power button / WiFi / ECO card, first remove the keyboard top cover (see Keyboard) and
then perform the following steps:
1. Remove the two screws holding the card.
2. Carefully disconnect the flat cable.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Fig. 27 Removing the power button/ WiFi / ECO card.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Notice
The information in this guide is subject to change without notice.
This guide contains information protected by copyright. No part of this guide may be photocopied or
reproduced in any form or by any means without prior written consent from Packard Bell B.V.
PACKARD BELL B.V. SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR
OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
Copyright © 2006 Packard Bell B.V. All rights reserved.
Packard Bell is a trademark of Packard Bell B.V.
The names of actual companies and products mentioned herein may be trademarks and/or registered
trademarks of their respective owners.
The software described in this guide is furnished under a license agreement or nondisclosure agreement.
The software may be used or copied only in accordance with the terms of the agreement.
EasyNote GN45 Disassembly Manual
Author: Olivier Raimbault & Juan M. Calviño
First Edition: July 2006
Version: 1.0
Packard Bell B.V.
Packard Bell EasyNote GN45 Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
|