Outlaw Audio Stereo Amplifier 200 M Block User Manual

Model 200 M-Block

Power Ampliﬁer

Owner’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Owner’s Manual

Unpacking

Table of Contents

Model 200 M-Block

Power Ampliﬁer

Welcome to the Outlaw Family! With your purchase of a Model 200 M-Block

Ampliﬁer you have become part of a unique, worldwide community of audio-

philes and home theater enthusiasts. With one or more Model 200 ampliﬁers

you have the option to add power and ﬂexibility to your system for a wide range

of applications, such as; adding rear surround channels to a new 7.1 system,

powering passive subwoofers, enabling bi-amp speaker conﬁgurations, power-

ing multi-zone/multi-room speakers and much more.

Model 200 M-Block Power Ampliﬁer

Features

Unpacking

Front Panel and Rear Panel

Installation and Conﬁguration

Power Control Connections

Speaker Wire Connections

Model 200 Connection Diagram

Audio Signal Connections

AC Power Connection

The Model 200 is compact, yet powerful, delivering 200 watts at eight ohms

(20Hz–20KHz, >0.05%THD). Thanks to a unique circuit design and a heavy-

duty power supply with a horizontally oriented torroidal transformer, the Model

200 operates without a fan despite the deep power reserves.

Operation

Care and Maintenance

Cleaning

Since the Model 200 will often be used in multiple unit systems, a variety of

power control options are provided. In addition to a standard power on/off

switch, the Model 200 may be operated from the external trigger control of

compatible products such as the Outlaw Model 950. Both in and out trigger

jacks are provided so that the control signal may be cascaded. For systems where

an external trigger is not available, the Model 200’s music sense circuitry is

available for automatic turn-on whenever an audio signal is present.

Troubleshooting Guide

Protection Circuitry

Fuse Replacement

Outlaw Service Information

Troubleshooting

In order to fully enjoy the performance of your ampliﬁer, please take a few

minutes to read this owner’s manual. It contains important information that

will help you to make certain that the ampliﬁer is properly conﬁgured for

operation with the rest of the equipment in your system.

A Few Words About Hum and Noise

Potential Ground Loops in a Complex A/V System

10 Speciﬁcations

Once again, welcome to the Outlaw family!

11 The Outlaw Audio 30-Day Satisfaction Guarantee

11 Outlaw Audio Limited Warranty

Features



High-power M-Block ampliﬁer



Unique dual-topology circuit design



Music Sense circuitry and low voltage trigger connection for automatic

turn-on



Five-way binding posts accommodate large gauge speaker cable



Fan-free convection cooling



Efﬁcient power supply with torroidal transformer



Removable IEC power cord

Unpacking

The carton and packing materials used in shipping your new ampliﬁer were

specially designed to cushion it from the shocks and vibration of shipping. We

strongly suggest that you save the carton and packing materials to use if you

move, or if the unit ever needs to be shipped back to us for any reason.

duplicated or reproduced by any means, whether physical, electronic or otherwise without

prior written consent from Outlaw Audio.

To minimize the size of the carton in storage, you may wish to ﬂatten it by

carefully opening the top and bottom ﬂaps and folding the carton ﬂat. Other

cardboard inserts may be stored in the same manner. Packing materials that

cannot be collapsed should be saved along with the carton in a plastic bag.

Speciﬁcations are those in effect at the time of printing. Outlaw Audio reserves the right to

change speciﬁcations or designs at any time without notice or liability to modify or upgrade

units previously sold.

Model 200 M-Block Power Ampliﬁer

Download from Www.Somanuals.com. All Manuals Search And Download.

Owner’s Manual

Front and Rear Panel

Front Panel and Rear Panel

��

�

��

Jack of an additional Model 200. Note, however, that connecting more than

two Model 200s to a single source controller may overload the system and

is not recommended. If you wish to automatically turn on more than two

Model 200 units, we recommend the use of either the music sense circuitry

or an externally powered relay controller. Contact Outlaw Audio Customer

Service for more information on using the Model 200 in multiple unit

systems to avoid damage to your processor, receiver or controller.

The front panel LED indicator has three modes:

Amber: Indicates that the Model 200 is connected to an AC power source and

the rear-panel Main Power switch is turned on. When the indicator is amber,

the unit is in the Standby mode and is ready to turn on when a control signal

is received at the trigger jack or from the music sense circuitry.

Green: Indicates that the Model 200 is on and operational.

Red: Indicates that the Model 200 is in the Protect mode. If the LED is red,

you should turn the unit off and then check for the source of the condi-

tion that caused the overload. This may be a shorted speaker lead or other

similar condition. In the event of repeated appearance of the red LED you

may have a chronic system failure with either the Model 200 or another

component in your system. In this case disconnect the Model 200 from AC

power and the rest of your system and consult Outlaw Audio’s Customer

Service Department for assistance.

Trigger Mode Switch

This three-position switch determines the method by which the Model 200

will be placed in the active, or ON, position:



When the switch is in the far right position, under the word “ON,” the

unit will be turned on when the Main Power Switch is turned on.



When the switch is in the middle position, under the word “MUSIC,”

the unit will automatically turn on when an audio signal is present at

the Input Jacks. The unit will automatically turn off when the signal

is no longer present.

Input jack

Connect this jack to the output of the source used to feed the Model 200.

Note that if the Trigger Mode switch is turned to Music, the Model 200 will

turn on whenever an audio source is present at this jack.



When the switch is in the far left position, under the “12V” indication,

the unit will automatically turn on when a 6-volt to 35-volt signal is

applied to the Trigger Input Jack. The unit will turn off shortly after

that signal is removed.

Trigger Input Jack

Connect this jack to the trigger output jack of a compatible product such

as an Outlaw Audio Processor or Receiver that is capable of providing a

6-volt to 35-volt control signal at turn-on. When the Trigger Mode switch

is set to the 12 Volt position, the Model 200 will turn on when the control

signal is present.

Speaker Output Jacks

These jacks provide the ampliﬁed power signal for connection to your

speaker.

Input Voltage Switch

This switch selects the power AC input voltage for the Model 200, depending

on the AC power system used in your area.

Trigger Output Jack

When more than one Model 200 is used in an system, this jack may be

used to pass the low voltage control signal through to the Trigger Input

Outlaw Audio

Download from Www.Somanuals.com. All Manuals Search And Download.

Owner’s Manual

Speaker Wire Connections

IMPORTANT NOTE: Do not make any change to this switch setting unless

the ac power cord is removed from the unit so that the ampliﬁer is totally

disconnected from any ac power source.

Model 200. Connect the other end to a matching jack on the device that

will be provide a 6 to 35 volt signal when the unit is to be turned on.

3. If the source controller does not have a trigger jack, you may use the

music sense option to automatically turn on the Model 200, however, you

may also use the trigger switch if the source controller has a switched AC

Accessory outlet. If that is the conﬁguration you wish to use, purchase a

small AC to DC power converter, as typically used to replace the batteries

in portable electronics devices. Select a model that is capable of delivering

6 to 35 volts DC, and make certain that one of the “tips” provided with

the unit is a 3.5mm mini-plug. Plug the transformer end of the converter

into the switched AC output on the source product, and connect the 3.5mm

AC Power Switch

Turn this switch to the ON position to operate the Model 200.

Fuse

This fuse is used to protect the power supply only and is NOT part of the

speaker protection circuitry. If you suspect that the fuse has blown, ﬁrst

disconnect the Model 200 from the AC power source by removing the power

cord, and then connect the condition that lead to the blown fuse.

IMPORTANT NOTE: The replacement fuse should have the proper rating

for the voltage setting in use and must be of the correct type. Consult the

data printed on the ampliﬁer’s rear panel for fuse information.

mini-plug to the Trigger Jack

4. Press the Power Switch in so that it is engaged, and note that the Standby

Indicator will light for the channel pairs selected for trigger control

operation.

If the fuse blows repeatedly, discontinue use of the product and contact

Outlaw Audio Customer Service for further assistance.

When the source control unit providing the power is turned on, the Model 200

will automatically turn on. When the source unit is turned off, the Model 200

will return to the standby mode.

AC Power Cord Receptacle

Connect the AC power cord supplied with the unit to this receptacle, and

connect the power cord plug to an AC outlet.

Remote Turn-On Using Music Sense

To conﬁgure the Model 200 so that it will automatically turn on when the

ampliﬁer is receiving an audio signal, follow these steps:

IMPORTANT NOTE: A replacement power cord must be equal to the cord

supplied with the unit.

Installation and Conﬁguration



Connect the audio input as normal to the Input Jack

SAFETY NOTE: When making connections between any source compo-

nents such as AV Receiver, surround processors or multi-room controllers

and the Model 200, or when making any connections to speakers, be

certain that both the source device and the Model 200 are turned off. To

ensure that there will be no unwanted signal transients that can dam-

age equipment or speakers, it is always best to unplug all equipment

before making any connections. Modern electronic products often have

a “standby” mode that may be activated even though they product may

appear to be tuned off.



Turn the Trigger Mode Switch so that it is in the center position under

the word “Music.”

Make sure the AC Power Switch is turned on. Note that the front panel

LED will turn amber indicating that the unit is in the Standby mode,

awaiting a signal that will activate the operational mode.

In this conﬁguration, the Model 200 will automatically turn on whenever it

is receiving an audio input signal. The unit will return to the standby mode a

few minutes after the audio signal stops.

Power Control Connections

Speaker Wire Connections

The Model 200 features a built-in remote turn on system that will automatically

turn on the ampliﬁer in one of two ways. Depending on your speciﬁc applica-

tion, the unit may also be turned on manually using the Rear Panel AC Power

Switch, or automatically via sensing of either an input source or a low voltage

trigger signal. For manual operation, no special installation is required. For

automatic turn-on, follow the instructions below for the chosen method.

It is always best to connect the ampliﬁer to your speakers using high quality

cable. The Model 200 is equipped with ﬁve-way binding post terminals that

accept bare wire, spade lugs or banana type plugs when they are permitted

by local safety agencies. Once you have located the proper speaker terminals

for the type of output conﬁguration in use, connect your speakers using the

following guidelines.

Remote Turn-On From An External Device

Using The Low Voltage Trigger

To conﬁgure the Model 200 so that it turns on automatically in response to a

low voltage trigger signal, follow these steps:

To assure that the high quality signals produced by your Model 200 are car-

ried to your speakers without loss of clarity or resolution, we recommend that

you use high quality speaker cable. Many brands of cables are available, your

choice may be inﬂuenced by a number of factors; i.e.: the distance between

your speakers and the ampliﬁer; the type of speakers you use; personal prefer-

ences; and other factors.

1. Place the Trigger Power Control Mode Switch in the far right position,

so that the switch is under the words “12 VOLT.”

Regardless of the brand or type of cable selected, we recommend using a cable

constructed of ﬁne, multi-strand copper with a gauge of 14 or larger. Remember,

that in specifying cable, the lower the number, the thicker the cable.

2. To trigger the ampliﬁer from a device such as a surround processor, AV

Receiver or multi-room controller with a built-in trigger jack, connect one

end of a cable with a 3.5mm mono mini plug to the Trigger Jack on the

Model 200 M-Block Power Ampliﬁer

Download from Www.Somanuals.com. All Manuals Search And Download.

Owner’s Manual

Model 200 Connection Diagram

��

�

��

�

��

�

��

�

Cables with a gauge of 16 may be used for short runs of less than ten feet. We do Then, loosen the knobs of the speaker output terminals, far enough so that the

not recommend that you use any cables with an AWG equivalent of 18 or higher pass-through hole is revealed. Note that one conductor of the speaker cable will

due to the power loss and degradation in performance that will occur.

have no markings, and the other will have a red line, brand name markings, a

black thread, or some other positive indication. Follow the proper connection

instructions for your system with regard to which terminals are used so that

proper system polarity is maintained by connecting the positive (usually red)

terminal on the speaker to the positive terminal on the Model 200 and the

negative (almost always black) terminal on the speaker to the black negative

terminal on the Model 200. After the connections are made, twist the cap back

so that the connection is secured, but do not over tighten or use tools, as this

may break the delicate wire strands and decrease system performance.

Cables that are run inside walls should have the appropriate markings in

indicate listing with UL, CSA or other testing agency standards. Questions

about cables inside walls should be referred to a qualiﬁed installer or a licensed

electrical contractor who is familiar with the NEC and/or the applicable local

building codes in your area.

If bare wire is used for the connections, strip approximately 1/2 inch to 3/4

inch (20mm) of insulation from the end of each wire and carefully twist the

strands of each conductor together. Be careful not to cut the individual strands

or twist them off; for optimal performance, all strands must be used.

Outlaw Audio

Download from Www.Somanuals.com. All Manuals Search And Download.

Owner’s Manual

Operation

If you are using spade lugs, connect them to the wire using the manufacturer’s

instructions, and then loosen the caps on the speaker terminals. Place lugs

between the plastic cap and the back of the terminal, as if it were a horseshoe

on the game’s post. Again, remember to observe proper polarity. Tighten with

your ﬁngers to obtain a positive contact.

Operation

Operation of the Model 200 is simple. In normal use there are no controls to

adjust once the installation is complete.

After all connections have been made to the ampliﬁer’s inputs and speaker

terminals have been made, and the AC power cord has been connected, the way

in which the unit turns on is determined by the setting for the Trigger Mode

When banana plugs are permitted, connections may be made by simply insert-

ing the jack afﬁxed to your speaker wire into the hole provided on the rear of

the colored screw caps on the binding posts. Before using banana type jacks

make certain that the plastic screw caps are ﬁrmly tightened down by turning

them in a counter clockwise direction until they are snug against the chassis.

This will ensure that the maximum surface area of the plug is in contact with

the jack. Be certain to observe proper polarity.

Switch . Depending on the setting, as described on page 5, the ampliﬁer

will turn on in one of these three ways:



When the Trigger Mode Switch is set to the left, in the “On” position,

the Model 200 will turn on when the AC Power Switch

Use the switch to turn the Model 200 off when your ﬁnished listening.

is turned on.



When the Trigger Mode Switch

is set in the center, in the “Music”

Finally, run the cables to the speaker locations. Where possible, it is recom-

mended that the length of cable connecting any pair of speakers is identical

even though one speaker may be physically closer to the ampliﬁer than the

other. Do not coil any excess cable, as this may become an inductor that creates

frequency response variations in your system.

position, the AC Power Switch should be turned ON to place the Model

200 in the Standby Mode. The unit will automatically turn on whenever

an audio signal is present. The unit will return to the Standby mode a few

minutes after the audio signal is removed.



When the Trigger Mode Switch is set to the right, in the “12V” position,

NOTE: While most speaker manufacturers adhere to an industry conven-

tion of using black terminals for negative and red ones for positive, some

manufacturers may vary from this conﬁguration. To ensure proper phase

connections, and optimal performance, consult the identiﬁcation plate on

your speaker terminals, or the speaker’s manual to verify polarity. If you

do not know the polarity of your speaker, ask your dealer or installer of

advice before proceeding, or consult the speaker’s manufacturer.

the AC Power Switch

should be turned ON to place the Model 200 in

the Standby Mode. The unit will automatically turn on when a low voltage

signal is present at the Trigger Jack

when the host product’s trigger signal is removed.

and return to the Standby Mode

As a general rule, it is always a good idea to turn on your ampliﬁer LAST. This

avoids the possibility of any turn on pops or transients from other equipment

being ampliﬁed and sent to your speakers where they may cause damage.

Always start with a low volume level on your receiver, controller or preamp to

avoid damage to your speakers.

As a general rule, always avoid running input signal or speaker wire connections

in parallel with each other, or with AC power cords. This can result in undesired

hum or other interference that will greatly degrade signal performance.

Audio Signal Connections

SAFETY NOTE: To prevent unintended operation, remember to turn the

unit completely off when it will not be used for an extended period of time.

This is done by turning the AC Power Switch OFF and noting that the front

panel; LED indicator goes off. This will prevent the automatic turn on circuits

from accidentally turning the ampliﬁer on during your absence.

Audio connection to the Model 200 is simple and straight-forward: Connect the

output of the source unit, which may be the preamp, multi-room or subwoofer

output of a surround processor, stereo preamp, AV receiver or “whole-house”

audio system controller to the Audio Input Jack

Note: There are no output level controls on the Model 200, as the level

is determined by the signal received from your source device. We recom-

mend that after installing a new ampliﬁer such as the Model 200 that you

always re-calibrate your system to ensure that the system levels match

at all speaker locations.

When making connections with the “RCA” type plugs on interconnect cables,

make certain to gently, but ﬁrmly insert them into the jacks on the back of the

Model 200. Loose connections can cause intermittent sound and may dam-

age your speakers. The barrel assembly of some high quality RCA plugs may

be very tight, and it is important to ensure a proper connection between the

interconnect cable and the input jack.

AC Power Connection

The ﬁnal step in the installation of the Model 200 is to connect the power cord.

First, connect the female end of the cord into the AC Power Receptacle on

the rear panel. Once the cord as been ﬁrmly connected to the Model 200, insert

the plug end into an AC power outlet.

Safety Notes



Due to the current draw of the Model 200, DO NOT connect the power cord

to the accessory outlet of an audio/video component.

Should the power cord become lost or damaged, be certain to replace it



with a replacement that meets or exceed the original speciﬁcations. Use of

power cords with insufﬁcient capacity, such as those used with computers

or ofﬁce equipment, may create a safety hazard.

Model 200 M-Block Power Ampliﬁer

Download from Www.Somanuals.com. All Manuals Search And Download.

Owner’s Manual

Care and Maintenance

to make certain that none of the strands from the “positive” terminal touch

those from the “negative” terminal. Even a few stray wire strands can cause

the unit to go into the protection mode.

Care and Maintenance

Cleaning

When the unit becomes dirty, wipe it with a clean, soft, dry cloth. If necessary,

ﬁrst wipe the surface with a soft cloth slightly dampened with mild soapy water,

then with a fresh cloth dampened with clean water. Wipe dry immediately

with a dry cloth. NEVER use benzene, thinner, alcohol or any other volatile

cleaning agent. Do not use abrasive cleaners, as they may damage the ﬁnish

of the metal parts. Avoid spraying insecticide, waxes, polishing agents, or any

aerosol product near the unit.

After checking all speaker connections, turn the unit back on. If it continues

to turn off, check your speakers to verify that they are operating properly. If all

other potential sources of trouble check out properly, contact Outlaw Audio for

further assistance and information.

Fuse Replacement

The fuse on the Model 200’s rear panel protects the unit’s power supply from

problems and is not part of the audio circuit. If you suspect that a malfunction

of the unit is caused by a blown fuse, be certain to replace it with an identical

type. Should the fuse continue to blow, discontinue use of the Model 200 and

disconnect it from both AC Power and all source components. Contact Outlaw

Audio for service information.

Troubleshooting

Your Outlaw M-Block Ampliﬁer is designed for trouble free operation. If you

follow the instructions in this manual you should enjoy many years of high

quality listening enjoyment. However, as with any sophisticated electronic de-

vice, there may be occasional problems upon initial installation, or during the

life of the unit. The items on this list are a brief guide to the minor problems

that you may be able to correct yourself. If these solutions do not rectify a

problem, or if the problem persists, contact us for assistance.

Outlaw Service Information

The Model 200 does not contain any user serviceable parts. If you suspect a

problem that may require service assistance, contact us via e-mail at custome

[email protected], or by phone at 866-OUTLAWS (688-5297).

Protection Circuitry

It is important that an authorized service agent carry out any repairs. This

will ensure proper service and preserve the protection of your Limited War-

ranty. Keep your sales slip or receipt in a safe place with this manual so that it

will be available to verify the purchase date should you experience a problem

covered by our warranty.

In the event that the ampliﬁer senses a shorted speaker wire, DC voltage on an

input connection, or thermal overload that could potentially cause damage to

the unit or to your speakers, it will automatically shut down.

If this should happen, ﬁrst check all speaker wire connections, both at the

speakers themselves and at the speaker terminals on the back of the Model 200

Troubleshooting Guide

Problem

Solutions

Ampliﬁer will not turn on

Master Power Switch turned off (No power light LED).

Turn on Master Power Switch.

Ampliﬁer will not turn on

Remote trigger cable not properly connected.

Verify connection of trigger cable at both ends.

Ampliﬁer turns on, but no audio is heard

No audio

Input plug not connected properly or is loose.

Check input connection.

Speaker not connected properly.

Check speaker connections at amp and speaker

Audio levels differ from other channels in the system

Audio plays, then cuts off

Improper settings or output levels from the processor or controller.

Check the settings on your preamp, processor or controller.

Ampliﬁer shorted.

Check speaker connections for short circuit at amp and speaker.

Outlaw Audio

Download from Www.Somanuals.com. All Manuals Search And Download.

Owner’s Manual

A Few Words About Hum and Noise

Ground Loop Diagram

Set-top Box

Coax Cable

Cable Feed

A/V

Cables

60Hz AC

Ground Loop

60Hz AC

Ground Loop

AC Line

AC Ground

Main House

Grounding

wire where it is connected at the wall outlet. Turn your system back on, and

listen if the hum has disappeared. If removing the cable TV feed has eliminated

the hum, you will need to insert a Ground Loop Isolator before reconnecting

the cable TV feed, or contact your cable TV operator to see if they can better

isolate your cable feed.

A Few Words About Hum and Noise

Audible hum, or a discernable low frequency noise, is one of the most com-

mon problems in audio/video systems. This hum, which may be present even

when the volume is at a low level or when the power is off, is usually caused

by a problem known as a “ground loop”. A ground loop occurs when there

is a difference in ground voltages between two or more components that are

connected electrically. This, in turn, creates multiple current paths and causes

the low-level noise, or hum.

Suggestion #2:

Turn off all components in your system, and then disconnect the input cables

at the ampliﬁer. Turn the ampliﬁer back on, and see if the hum is still present.

If the hum disappears, the fault may be in the input cables used. Try replacing

them with cables that have better shielding, and make certain that the input

cables are not running on top of any AC power cords. Change the cables one

at a time to determine if one, or all cables is responsive. If the hum disappears

when the input cables are disconnected, but returns after the cables are changed

and the system re-connected, the problem may be caused by your processor,

receiver or preampliﬁer.

The growing sophistication of home theater systems, and the increased number

of components used to create these systems has dramatically increased the

potential for the possibility of ground loops. While it is natural to suspect that

the components in your system are the cause of the hum, in many cases the

cause may be due to other conditions. In particular, cable TV connections from

outside the house have become a major source of hum.

In most cases, one of the following suggestions should help you to solve a

hum problem in your system. Please try these steps in the sequence shown,

proceeding from one step to the next if the prior suggestion does not eliminate

the problem.

Suggestion #3:

Poor grounding of the electrical system in your home may also cause ground

loop problems, particularly when there are multiple components with three

prong, grounded, power cords. Try unplugging these components one at a

time, and see if one or all of them is causing the problem. The ultimate solu-

tion to this type of problem is to re-wire your house with an isolated, star-type

grounding conﬁguration. We recognize, however, that this may be impracti-

cal and expensive. In some cases, the use of an approved AC Power Isolation

Transformer of sufﬁcient capacity may solve this problem.

Potential Ground Loops in a Complex A/V System

Suggestion #1:

To determine if a cable TV connection is responsible for the hum, ﬁrst turn all

components off. Disconnect the cable TV feed to your system at the ﬁrst place

where it connects to your components. Alternatively, disconnect the cable TV

Model 200 M-Block Power Ampliﬁer

Download from Www.Somanuals.com. All Manuals Search And Download.

Owner’s Manual

Speciﬁcations

Warning: if you suspect that the grounding system in your home’s electrical

wiring is causing the hum problem, it is important that you do not make

any changes to the wiring yourself. Only a licensed electrician should

make any changes to household wiring, and they must be made in full

compliance with all local building, safety and electrical codes.

Speciﬁcations

Power Output

200 watts @ 8 ohms, 20 Hz 20 kHz, <0.05% THD

300 watts @ 4 ohms, 20 Hz 20 kHz, <0.05% THD

Suggestion #4:

THD Signal to Noise

Trigger Input

100 dB (un-weighted)

6-35V DC 4mA

Faulty earth grounds may also cause hum in your home’s electrical system. In

the past, cold water pipes were often used for the earth ground, so it is important

to make sure that your ground connection is still valid and has not become

loose or corroded. The cold water pipe method may no longer be valid in some

locations due to requirements that the water meter be isolated from the water

mains with a length of PVC pipe, thus interrupting the ground circuit. The

safest, and most reliable, approach may be to provide your own ground. This

can be accomplished by having a licensed electrician drive at least ﬁve feet

of copper-jacketed steel grounding rod into the earth, and using that for your

grounding connection.

Operating Mode

Input Impedance

Gain

Class G/AB

>10K Ohms

+27dB (1.7V sensitivity) for full output

RCA Jack

Input Connector

Output Connectors

Power Consumption

Weight

Five-Way binding posts

600 watts maximum; <3 watts standby

18 pounds /8.165 Kg.

1.5” x 17” x 11.5”/40mm x 430 mm x 330 mm

Suggestion #5:

If you have hum in your video display device (bars that roll up through image

at 12-14 second intervals), this may be related to hum you also experience in

your audio system. The previous suggestion tips may help with this also. If not,

try isolating the ground in the projectors video signal cable with a base-band

video isolation transformer, such as the Jensen VB-1BB.

Dimensions (H/W/D)

Note: Due to our policy of continual improvement, all speciﬁcations are subject

to change without notice or liability to upgrade previously shipped units to current

speciﬁcations or standards

If the hum persists after all of the above suggestions have been tried, contact

the Outlaw Audio customer service department for assistance.

10 Outlaw Audio

Download from Www.Somanuals.com. All Manuals Search And Download.

Owner’s Manual

Outlaw Audio Limited Warranty

The Outlaw Audio 30-Day Satisfaction Guarantee

This product is guaranteed to satisfy all your needs for a high performance

power ampliﬁer. If for any reason, you are not completely satisﬁed with it,

please contact us at 866-OUTLAWS (688-5297) within 30 days of receipt of

the unit and you will receive a return authorization.

will be adequately protected.

If you decide to return the ampliﬁer, the only cost you will be responsible for

is the shipping charge to return it to us. When your ampliﬁer arrives, we will

inspect it to insure that it was shipped back to us in original condition. Upon

satisfactory inspection, we will issue a full credit for your original purchase

price plus your original outbound freight cost at standard ground shipping

rate.

Please save all of your packing material in that the ampliﬁer is heavy and

can get damaged in shipping without proper protection. We recommend that

you keep the packing (even after 30 days) so that if you ever move, the unit

(Replacement cartons are available at a modest charge.)

Outlaw Audio Limited Warranty

This warranty protects the owner of the Outlaw Model 200 Power Ampliﬁer

(the PRODUCT) for ﬁve (5) years from the date of purchase.

If your product needs service, please call Outlaw Audio at 866-OUTLAWS

(688-5297).

You will need to present the original bill of sale to establish the date of

purchase. In the event that the proof of purchase cannot be established

with the original receipt, the warranty period shall be determined by the

earliest date of manufacture shown on the unit, provided that the serial

number label has not been altered in any manner, or by our records

relating to that serial number.

This warranty covers all defects in material and workmanship with the

following speciﬁc exceptions. These are:

• Damage caused by improper installation or adjustment

• Damage caused by connection to AC power outside of the speciﬁed

range

• Damage caused by accident, unreasonable use or neglect

In the event that you wish to return your Outlaw ampliﬁer back to us, for

any reason, please call to arrange for a Return Authorization Number.

This will ensure that your problem is discussed with a service technician

who will determine if there is a quick solution to your problem.

• Damage from failure to follow instructions contained in this Owner’s

Manual

• Damage from the performance of repairs by someone not authorized

by Outlaw Audio

Outlaw Audio shall not be liable for, or in anyway responsible for, inci-

dental or consequential damages of any kind. Some states do not allow

limitations on how long an implied warranty lasts and/or do not allow the

exclusion of incidental or consequential damages. Therefore, the limita-

tions and exclusions stated herein may not apply to you. This warranty

gives you speciﬁc legal rights; and you may also have other rights, which

may vary from state to state.

• Any unit on which the serial number has been effaced, modiﬁed, or

removed

• Damage occurring during shipment (Consult the carrier for claims

due to shipping damage)

• Units which have been altered or modiﬁed in design, appearance or

construction

THERE ARE NO WARRANTIES GIVEN BY OUTLAW AUDIO, WHICH EXTEND

BEYOND THE DESCRIPTION GIVEN HEREIN. ANY IMPLIED WARRANTIES

OF FITNESS FOR PURPOSE SOLD, MERCHANTIABILITY, DESCRIPTION,

QUALITY OR ANY OTHER MATTERS ARE LIMITED TO THE TERMS OF THE

EXPRESSED LIMITED WARRANTY STATED HEREIN.

This warranty covers only the actual defects within the PRODUCT itself.

IT DOES NOT cover costs of installation in (or removal from) a ﬁxed

installation, or normal set-up, claims based on any misrepresentation by

the seller, or performance variations resulting from installation related

circumstances such as signal quality, AC power or incompatibilities with

speakers and/or other system components.

Products are sold on the basis of speciﬁcations applicable at the time of

sales. Outlaw Audio shall have no obligation to modify products once

they have been sold.

During the warranty period, Outlaw Audio will, at its option, either repair

the defect, or replace the defective product, or the defective parts, or com-

ponents thereof at no charge to the owner for parts and labor covered by

this warranty. If necessary repairs are not covered by this warranty, or if

a unit is examined which is not in need of repair, you will be charged for

the repairs and/or the examination. If non-warranted repairs are needed,

we will notify you of the estimated cost and ask for your authorization

to perform said repairs.

This warranty is applicable only in the United States.

For applicability in other countries, please call Outlaw Audio.

Reserved. Any unauthorized duplication, publication or distribution by any

means or in any form, whether physical, electronic or otherwise is strictly

prohibited without prior written consent from Outlaw Audio. LLC.

You must pay shipping charges incurred in getting your Product to the

factory. We will pay the return shipping charges if the repairs are covered

by the warranty. Please save the original shipping cartons, as the unit

MUST be returned in the original carton and packing.

Model 200 M-Block Power Ampliﬁer 11

Download from Www.Somanuals.com. All Manuals Search And Download.

Nady Systems Microphone SPC 15 User Manual
Nady Systems Stereo System MM242 User Manual
Nortel Networks Welding System 411 2021 111 User Manual
Nostalgia Electrics Saw HSM 245 User Manual
Olympus Camera Lens ED150mm f20 User Manual
Omega Vehicle Security Switch LVUN 600 User Manual
Omron Marine Radio 3G3FV PDRT1 SIN User Manual
Panasonic All in One Printer KX FL611 User Manual
Panasonic Bluetooth Headset KX TG7622 User Manual
Panasonic Photo Scanner DMW YAGHPP User Manual