Oregon Scientific Light Therapy Device E8612 User Manual

SPF setting options:  
The SPF range is between 1-70. Enter an SPF setting  
that corresponds to the SPF protection of the sunscreen  
product you are using.  
DISPLAY  
To toggle display modes:  
Press MODE / SET to toggle display mode between:  
Portable UV Monitor  
(Models: EB612 / UV888)  
Clock Mode: time, UV level and temperature  
Timer Mode: timer, UV level and temperature  
UV mode: UV index, UV level and UV exposure time /  
timer.  
USER MANUAL  
UVI DISPLAY  
UV INDEX  
INTRODUCTION  
Thank you for selecting the Oregon ScientificTM Portable  
UV Monitor.  
LEVEL  
Low  
UVI DISPLAY  
0-2  
NOTE Please keep this manual handy as you use your new  
product. It contains practical step-by-step instructions, as  
well as technical specifications and warnings you should  
know.  
3-5  
6-7  
Medium  
High  
1. UV Index icon  
2. UV measurement icon  
3. Exposure alarm  
4. Low battery icon  
5. Exposure timer icon  
6. Clock / timer  
OVERVIEW  
FRONT VIEW  
8-10  
Very high  
7. Temperature display  
8. Key lock icon  
9. Skin type / Sun Protection Factor icons  
11-25  
Extremely high  
GETTING STARTED  
STRAP  
and “HH” on  
LCD display  
25+  
Over range  
Wear on the wrist or attach using the strap as shown.  
To measure UVI:  
1. Press UV. The sensor will measure continuously for 4  
seconds. Rotate the unit by 360o while the sensor is  
reading to provide a more accurate measurement.  
2. Unless there is an exposure timer activated skin type  
and SPF will be displayed consecutively during this  
time.  
3. UV index, UV level and exposure timers will be  
automatically be updated.  
NOTE  
If no timer is set the display will clear after 30mins.  
BATTERIES  
The unit uses a CR2032 battery.  
UV EXPOSURE TIMER  
After taking a UV measurement in UV mode the monitor  
calculates a recommended maximum exposure time based  
on the skin type and SPF set by the user.  
Insert the battery before first use, matching the polarity  
(+ and -):  
NOTE  
1. Sensor  
2. UV: measure UV level  
Please set your skin type before using the exposure  
timer. If you change the skin type or SPF, the exposure  
time will be adjusted automatically.  
The monitor automatically measures the UV level  
every 10mins when a timer is set. If the UV index has  
increased it will then adjust the timer to take account  
of the new levels.  
3. MODE / SET: toggle display modes, enter settings  
mode  
4. Strap loophole  
5. START / STOP / UP: start, stop and pause timers;  
adjust settings  
6. CLEAR / DOWN: stop timers; adjust settings  
IMPORTANT The calculated exposure time is a suggestion  
only.  
BACK VIEW  
appears when the battery is low.  
The unit powers on automatically after the battery is inserted.  
UV EXPOSURE COUNTDOWN TIMER  
ENTER SETTINGS  
To start a UV countdown:  
1. After UV exposure time has been calculated press  
START / STOP to start the timer.  
2. To pause the timer press START / STOP.  
3. Press START / STOP again to resume or press CLEAR  
to cancel the timer.  
Upon first use, battery change, or reset the monitor  
automatically enters setting mode.  
To enter settings:  
1. Press UP and DOWN to select the desired setting, press  
and hold to quickly scroll through the setting values.  
2. Press MODE / SET to confirm.  
4. When the timer has elapsed an alarm will sound.  
To silence the alarm:  
Press any button.  
3. The settings order is: 12/24 hr format, hour, minute,  
oC/oF, skin type, SPF.  
NOTE  
Use the table below to help you determine your skin type.  
First use the TANS / BURNS columns. If unsure, use the  
colour of your skin in an area that does not get exposed  
to sunlight to help guide you. Alternatively, eye colour can  
also be used as a guideline.  
Press UV during a countdown to manually force a UV  
measurement. The timer will automatically adjust the  
exposure time.  
After pausing and restarting the timer, press UV to  
ensure the timer remains accurate.  
Skin type setting options:  
MANUAL COUNTDOWN TIMER  
SKIN TANS /  
TYPE BURNS  
SKIN COLOUR IN EYE  
UNEXPOSED AREA COLOUR  
To set countdown timer:  
1. In timer mode, press and hold MODE / SET.  
2. Use UP and DOWN to select hour and minutes.  
3. Press MODE / SET to confirm.  
Never tans;  
always burns  
Pale or milky white; Blue  
alabaster  
1
2
1. RESET  
2. Battery compartment  
Sometimes tans; Very light brown,  
usually burns  
Blue  
sometimes freckles /Green  
To start manual countdown timer:  
Usually tans;  
sometimes  
burns  
Light tan, brown  
or olive; distinctly  
pigmented  
Gray/  
Brown  
1. Press MODE / SET to select timer mode.  
2. Press START / STOP To start the timer  
3. To pause the timer press START / STOP.  
4. Press START / STOP again to resume or press CLEAR  
to cancel the timer.  
LCD DISPLAY  
3
4
Always tans;  
rarely burns  
Brown, dark brown Brown  
or black  
5. When the timer has elapsed an alarm will sound.  
EB612_IM_USA_EN  
1
2006.3.3, 3:11 PM  
Download from Www.Somanuals.com. All Manuals Search And Download.  

NAD Stereo Receiver C315BEE User Manual
National Instruments Digital Camera NI 17xx User Manual
NetComm Network Card NP745n User Manual
New Holland Compact Loader 82LB User Manual
NordicTrack Home Gym NTEL75062 User Manual
NordicTrack Home Gym NTEX31961 User Manual
Nortel Networks Network Card 302403 G User Manual
Nortel Networks Switch 42C4911 User Manual
Olympus Camera Lens EX 25 User Manual
Panasonic Air Conditioner CS E18FKR User Manual