S I M P L Y
A M A Z I N G ®
UXSER’LS G7UIDE
605 EYB
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
7
8
9
15
25
35
16
17
18
19
26
27
28
29
2
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATING CLEANER,
READ ALL INSTRUCTIONS IN
THIS MANUAL CAREFULLY.
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical appliance, basic
precautions should always be followed,
including the following:
Table of Contents
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER
Maintenance and Customer Service, Polarized Plug Notice,
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . page
3
WARNING
Accessories, Warranty, Troubleshooting Guide . . . . . . . . . . . . page
4
To reduce the risk of fire,
electric shock, or injury:
Parts List, Assembly, Operating Instructions,
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page
5
General Information cont., To Replace Filter Dust Bag,
Bulb Replacement, How to Replace a Worn Belt,
To Adjust or Replace Brush . . . . . . . . . . . . . . . . . . . . . . . . . . . page
Edge Brush Replacement, Motor Filter and Oreck Fresh Air®
Scent Cartridge Replacement, Using an Oreck Fresh Air® Tab,
Stuffing or Blockage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page
• Do not leave appliance unattended when plugged in.
Unplug from outlet when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Do not operate the unit while in the upright and locked
position.
• Do not let the unit run while in any one stationary position
for any period of time. Keep the unit moving while in
operation.
6
7
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
Maintenance and Customer Service
• Use only as described in this manual. Use only
manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not
working as it should, has been dropped, damaged, left
outdoors, or dropped into water, return it to a service
center or call customer service at: 0845 603 0153.
• Do not pull or carry by cord, use cord as a handle, close
door on cord, or pull cord around sharp edges or corners.
Keep cord away from heated surfaces.
Your Oreck vacuum cleaner is a product of precise engineering. The
motor bearings are permanently lubricated and should not be oiled. If
you require additional information or have problems with your Oreck
appliance, you may call ORECK customer service at: 0845 603 0153.
Please specify the model number and serial/code number which can be
found on the data plate on the back of the vacuum.
Save your sales or purchase slip. Should your Oreck appliance require
warranty service, present this slip to the Authorized Service Center as
your proof of purchase.
• Do not run appliance over cord.
• Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair and anything
that may reduce air flow.
• Keep hair, loose clothing, fingers and all parts of body
away from openings and moving parts.
• Do not use to pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
• Do not use without filter bag assembly in place.
• Turn off all controls before unplugging.
Important Electrical Information
The wires in the main lead are coloured in accordance with the following
code:
Blue - Neutral
Brown - Live
If the colours of the wires in the main lead of this appliance do not corre-
spond with the coloured markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured blue must be connected to the terminal
marked with the letter N or coloured black. The wire coloured brown
must be connected to the terminal marked with the letter L or coloured
red. Do not make any connection to the terminal marked E or
or coloured green and yellow.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids,
such as gasoline or lighter fluid, or use in areas where
they may be present.
This appliance is double insulated and no earth connection is necessary.
If you remove the plug from power supply cord, dispose of it.
A shock hazard could result if incorrect plug is inserted into a
13 AMP socket outlet.
• Do not use appliance in an enclosed space where
flammable, explosive or toxic vapors are given off by oil
base paint, paint thinner, some mothproofing substances,
or in an area where flammable dust is present.
• Do not pick up toxic material such as chlorine bleach,
drain cleaner, gasoline, etc. with this appliance.
• Use caution when vacuuming over area rug edges and
fringe.
When changing fuse, replace with the same size
replacement fuse.
Never use the plug without the fuse cover fitted in place.
The fuse carrier is red and hinged to the plug. Do not use the plug
if it is different.
If necessary, you may contact customer service for replacement
fuse covers.
SAVE THESE INSTRUCTIONS
Household Use Only
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories (Sold Separately)
Troubleshooting Guide
ITEM
1.
PART #
WARNING: Unplug cord from electrical
outlet before servicing.
Dust Bag, 8 Pack, Saniseal®
Hypo-Allergenic
CCPK8DW
0300604
2.
3.
Belts, 3 Pack
Fresh Air® Scent Cartridges
SAVE SERVICE CALLS...CHECK THESE FIRST:
• Is the disposable filter dust bag full?
• Are pores of filter dust bag clogged with powder or fine dust?
Notes of Vanilla®, 8pk.
FA1PK
FA2PK
FA3PK
77051-01
EF4PK
ORD24
AIRTABS
Spring Mullberries®, 8pk.
Blooming Jasmine®, 8pk.
• Is anything clogging the revolving brush, lower tube, intake opening,
fan housing or connector assembly opening?
4.
5.
6.
7.
Light Bulb
Exhaust Filter, 4pk.
24” Lambs Wool Duster
Fresh Air Tabs
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location?
• Does the brush turn freely? Are hair, string or rug fibers wound around
the brush?
Warranty
PROBLEM
CLEANER
POSSIBLE SOURCE
AREAS TO CHECK
ORECK MANUFACTURING COMPANY: (Oreck Manufacturing Company,
21180 Johnson Road; Long Beach, MS, USA 39560, gives you the
following limited warranty for this product only if it was originally purchased
for residential use, not resale from Oreck or an Oreck Authorized Retail
Dealer.)
Not plugged in
properly.
Be sure cleaner is
firmly plugged into
wall outlet.
WILL NOT RUN
No electricity in wall
outlet.
Check electrical
source–fuse or
circuit breaker.
Oreck will repair or replace, free of charge, to the original purchaser, any
part that is found to be defective in material or workmanship within seven
(7) years of the date of purchase. This limited warranty applies to normal
domestic use. Any commercial use of this product will void this limited
warranty. This limited warranty covers the revolving roller brush for one (1)
year for residential use only.
CLEANER
DOES NOT PICK UP
Filter bag is full.
Replace filter bag.
See “To Install Paper
Filter Dust Bag.”
This limited warranty does not cover the replacement of expendable or
consumable parts such as carbon motor brushes, edge brushes, drive
belts, brushes, bulbs, disposable bags and other parts subject to normal
wear unless they are defective in material or workmanship.
Nozzle or intake
pivot clogged.
Clear obstruction.
Replace belt.
Belt is broken or
stretched.
This limited warranty does not apply to any part subjected to accident,
abuse, commercial use, alteration, misuse, damage caused by act of God,
the use of voltages other than indicated on the serial number displayed on
this product or service of this product by other than Oreck or a partici-
pating Factory Authorized Service Center.
Brush is worn.
See “To Adjust or
Replace Brush”
Bag tube clogged.
Clear obstruction.
Change bag.
Oreck does not authorize any person or representative to assume or grant
any other warranty obligation with the sale of this product.
Bag pores are
clogged with fine
dust.
Oreck’s limited warranty is valid only if you retain proof of purchase from
Oreck or an Oreck Authorized Retail Dealer for this product. If you
purchase this product from any other source, your purchase is “AS IS,”
which means Oreck grants you no warranty, and that you, not Oreck,
assume the entire risk of the quality and performance of this product,
including the entire cost of any necessary servicing or repairs of any
defects.
Impeller fan is
broken.
Return to Service
Center for repair.
Revolving brush is
not even at both
ends.
Check brush roll
end cards. Make
sure words “normal”
or “special” match
at each end.
This warranty in addition to your statutory and other legal rights.
*Reconditioned units carry a 6 month warranty from date of
purchase.
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
CALL CUSTOMER SERVICE HOT LINE
0845 603 0153
Whenever calling, please be sure to have your model and serial
number from data plate.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Operating Instructions
To assist you in identifying components of your vacuum, the parts have
been numbered as follows:
Make sure disposable paper filter dust bag is in place. DO NOT operate
the cleaner without a paper filter dust bag. Plug the power cord into an
electrical outlet and press the ON(l) - OFF(O) switch on handle
assembly when ready to operate.
1
2
3
4
5
6
7
8
9
Helping Hand® handle
On/off switch
Cord dump
Handle tube
Bag stiffener
Deflector
Bag dock
Carry handle
Zipper
1
Up-Position Lock
2
fig. 3 Place foot on power head and lean handle back gently to release
lock for vacuum use. Return handle to the full upright position to
engage lock.
3
NOTE: Do not operate the unit while in the upright and locked position.
Do not let the unit run while in any one stationary position for any period
of time. Keep the unit moving while in operation.
4
10 Bag clip
5
Carry Handle
11 Headlight cover
12 Front light lens
13 Main bumper
14 Edge brush
15 Belt door
6
fig. 4 Raise the carry handle located on back of the unit for easy lifting,
carrying, and stair vacuuming. Lower the handle during use to
eliminate obstruction.
8
33
7
Duster Loop
16 Power cord
17 Cord assembly
18 Handle collar
19 Connector assembly
20 Carry handle clamp
21 Collars
22 Lower tube
23 Bag clip clamp
24 Scent cartridge door
25 Fan housing
26 Rear wheels
27 Side light
9
fig. 5 For convenient use of dusters, a loop has been sewn onto the
outer bag. This will allow easy removal and storage of the duster.
For Easy Power Cord Storage
fig. 6 Raise carrying handle and wrap power cord around carry handle
and cord dump.
10
fig. 7 To release cord, twist cord dump located on Helping Hand® handle
11
12
1/2 turn. Slide cord off handle. (fig. 8)
Cleaner Storage
The carry handle can be used for convenient, space saving storage of
cleaner. Hang cleaner by carry handle on a sturdy fastener.
13
15
14
28 Cover
Operating Recommendations
29 Bag spring
This new ORECK XL7 High-Speed Upright is one of the finest, fastest,
and strongest units in its class. You’ll love the way it cleans, gets under
things, and it’s SO lightweight and easy to use.
30 Bag pocket
31 Outer bag
32 Power nozzle
33 Inner filter bag
34 Duster loop
The following are a few simple suggestions regarding its operation:
1. When inserting a new disposable paper filter dust bag—FIRST
PUFF OUT and OPEN THE BAG.
17
16
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or makes an
unusual noise, STOP OPERATION and service.
18
31
4. Although your upright will pick up pins, paper clips, and other small
objects, it is recommended that these be removed from the floor
before you vacuum. Failure to do so may result in permanent
damage to the motor suction fan and its housing.
19
8
20
30
34
5. WARNING: Do not use your vacuum cleaner on damp or wet
surfaces. This will cause damage to the vacuum cleaner and is
dangerous to the user. Damage caused by use on wet or damp
surfaces is not covered under warranty.
21 22
29
28
6. REPLACE THE BELT EVERY 6 MONTHS, SCENT CARTRIDGE
EVERY MONTH, AND MOTOR FILTER EVERY 2 MONTHS.
23
24
7. Change the disposable filter dust bag at least once a month—even
if it is not full! The collected dust in the dust bag can cause odor,
attract moisture, and can affect the efficiency of the cleaner.
27
25
26
8. DO NOT run the vacuum cleaner over the cord. The revolving
brush could damage the cord.
14
32
Assembly
9. Use caution when vacuuming over area rug edges and fringe.
fig. 1 Align slot in handle tube with tab in connector. Insert the handle
tube into connector. Tighten collar at base of handle tube onto
the connector until it locks, “snaps”.
General Information
fig. 2 Snap cord assembly into the cord clip located on the left side of
the collar. Leave excess cord at the power head to allow
movement.
The performance of your new cleaner greatly depends upon care and
maintenance. The instructions in this manual will guide you in performing
basic care and maintenance. To obtain the most satisfying years of
service read the instructions and keep them handy for future reference.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor
Surfaces and Polished Floor Finishes
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role in the
efficiency of your ORECK vacuum cleaner. The purpose of the filter bag
is to trap dirt, but at the same time it must be porous enough to allow air
to pass through. If the filter bag becomes clogged, no air can pass
through the cleaner and cleaning cannot take place, regardless of the
cleaner’s power.
Use floor and floor finish manufacturer’s recommended methods of
cleaning. The plastic strip on the base of the cleaner could be damaged
if used on concrete or abrasive surfaces, and, therefore, cause damage
to wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished
floor finishes. The roller brush may also scuff very soft finishes. Do not
operate the unit while in the upright and locked position. Do not let the
unit run while in any one stationary position for any period of time. Keep
the unit moving while in operation.
To keep your cleaner operating at maximum efficiency, change the dust
bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE
DUST BAG.
To Replace Filter Dust Bag
Be sure the disposable paper filter dust bag is installed properly.
All paper dust bags are not the same. Your ORECK disposable
dust bags have been designed to be used with the ORECK cleaner.
Using bags other than genuine ORECK TYPE CC disposable bags
will affect the cleaning ability of your cleaner and could cause
damage to it.
WARNING: Unplug cord from electrical
outlet before servicing.
BAG REMOVAL:
fig. 10 Unzip outer bag completely.
HEPA-Celoc® Hypo-Allergenic Filter System
fig. 11 Pull bag cardboard collar to release bag dock door from
connector. Bag dock door will hinge downward.
The HEPA-Celoc outer bag of your vacuum cleaner is high filtration
medical material designed to filter the smallest of dust particles. It is
important the inside of the outer bag be cleaned. Vacuum the inside of
the outer bag or hand wash, turned inside out, with warm water, and air
dry. If desired, the HEPA-Celoc outer bag can be replaced for renewed
efficiency. The Celoc layered disposable inner dust bag must be
replaced once a month even if it is not full. Change it more often if it is
used in extremely dirty areas. Increase the cleaning power of your
vacuum by changing the bag often.
fig. 12 Gently pull bag cardboard collar upward out of the bag dock.
Saniseal® dust seal will close automatically.
BAG INSTALLATION:
fig. 13 Slide the cardboard collar completely onto bag dock door.
fig. 14 Firmly push bag dock door with both thumbs on indication point
until it snaps.
Bulb Replacement
The Belt
The belt on your vacuum cleaner controls the speed of the revolving
brush and is very important for the effective operation of the cleaner. If
the belt becomes stretched or cut, it will cause the revolving brush to
stop completely or slow down. See instructions in the manual for
replacing belt.
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 15 Remove lamp housing by removing two (2) screws in the top of
the lamp housing. Pull burned out bulb from holder and replace
with new bulb. Replace lamp housing by replacing two screws
in the top of the lamp housing.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts. Belts
other than ORECK belts will not operate the revolving brush
correctly and may create undue stress which will cause damage to
the motor and brush bearings. Using belts other than ORECK belts
will void the warranty.
How to Replace a Worn Belt
WARNING: Unplug cord from electrical
outlet before servicing.
Motor Filter
fig. 16 Remove the replacement belt from the storage channel.
The motor filter is used to filter tiny particles released by the motor
exhaust while in operation. The motor filter is not necessary for
operation but is helpful in removing contaminants from the air.
fig. 17 Remove the door by removing the hold down screw located on
side of power head.
fig. 18 Fold door away from the power head and lift it away.
NOTE: Motor filter should be replaced every two months for best
performance.
fig. 19 Remove the belt from the motor drive shaft and brush roll pulley.
Oreck Fresh Air® Cartridges
fig. 20 Loop the new belt over the brush roll pulley. Place the opposite
end of the belt on the motor drive shaft.
A fresh air cartridge adds a desired fragrance to the air while
vacuuming. It is placed behind the motor filter and uses heat and air
generated from the motor to spread the fragrance.
fig. 18 Replace the door by placing the bottom tab on door into slots
located inside power head and pressing the door closed.
fig. 17 Replace the hold down screw and tighten.
NOTE: Cartridge should be replaced every month when filter dust bag
is replaced or as desired.
To Adjust or Replace Brush
Lubrication
The vacuum cleaner motor bearings are factory lubricated and sealed.
Further lubrication is not required.
WARNING: Unplug cord from electrical
outlet before servicing.
Your Oreck Vacuum comes with the brush roll set at the NORMAL
position for most types of carpets. When using vacuum primarily on
Berber Carpets, adjust brush roll to the SPECIAL setting.
General Cleaner Care
fig. 9 At least once a month, check for and remove excessive lint,
string or hair from revolving brush. Patented cleaning grooves
on brush roll will allow easier cleaning.
fig. 21 Remove the baseplate by removing 5 screws. Then, remove the
belt and brush roll from the housing.
Wipe the outside of the cleaner with a damp cloth. Also clean the
connector deflector assembly area, base of cleaner and fan housing
area. If there is dust in the outer bag, vacuum it or shake it out.
fig. 22 Rotate both end cards of the brush roll to show “SPECIAL” and
replace in the holding channels of the housing.
A little preventative maintenance will keep your cleaner looking new and
will ensure continued cleaning effectiveness.
fig. 23 NOTE: The one marked “SPECIAL” has several ribs on top of
the end card.
fig. 24 The brush end card setting marked “NORMAL” has one rib.
When rotating bearings, make sure both end card assembly
settings are the same and face up when replacing the brush roll.
fig. 21 Reassemble the belt and the baseplate.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
fig. 32 To reassemble, check O-ring on tube, and replace if damaged.
Replace tube by first lining up slot at base of tube with tab inside
fan housing. Insert tube and push down until the tube is seated.
Make sure O-ring is in place against fan housing opening.
Replace and tighten collar until collar locking tabs are locked in
place. Reattach bag spring. (fig. 31)
Edge Brush Replacement
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 25 Turn the power head over. With baseplate facing up, remove the
screw located in the center of each edge brush. Remove both
edge brushes and replace with new ones. Replace both screws
and tighten.
fig. 35 Many times blockage occurs due to a full dust bag causing dirt to
back down the air flow system. When that happens, the
blockage will be at the top of the system, starting in the area
where the dust bag connects to the connector assembly.
NOTE: If the above actions do not correct the problem, contact an
Oreck authorized service center or call the customer service center
at: 0845 603 0153.
Motor Filter and Oreck Fresh Air®
Scent Cartridge Replacement
WARNING: Unplug cord from electrical
outlet before servicing.
The Motor Filter located at the back of the power head should be
replaced every 2 months. The Scent Disk should be replaced every
month when changing the inner filter bag.
fig. 26 Press two locking tabs on cartridge cover and remove the cover.
fig. 27 Remove the cartridge holder by lifting on tab at top of holder.
fig. 28 Remove old filter or scent disk from holder. Replace filter or
scent disk and reinsert holder.
Replace cover by aligning tabs on cover with slots in housing and
pressing the cover in place until cover tabs lock.
Using an Oreck Fresh Air® Tab
fig. 29 Your ORECK XL7 vacuum cleaner has a special FRESH AIR®
tab pocket. This pocket is located inside the outer bag in the
area where the disposable paper bag attaches to the intake
tube. Insert tablet in pocket if desired.
Stuffing or Blockage
IMPORTANT: On plush and new carpets, stuffing may occur inside the
intake tube and the lower tube assembly. This is due to excessive fuzz
and loose cuttings in the carpet. Stuffing could occur for the first few
cleanings until all the loose material is removed. Due to the high efficiency
of the cleaner, many older carpets will cause stuffing when the cleaner is
first used on them. If your vacuum cleaner does not pick up properly, or
makes unusual noise and the outer bag does not fluff up or balloon open,
follow these steps:
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 30 Check for blockage at the mouth of the intake opening. If there
is blockage, remove it with long-nose pliers, a screwdriver or
coat hanger. If you can not reach the blockage, remove
baseplate. (fig. 21)
fig. 31 If the blockage is not at the base, remove lower tube. Unhook
retainer spring, releasing bottom of bag.
fig. 32 Twist lower collar counterclockwise to slide up. Pull tube out of
base.
fig. 33 Check for blockage. If blockage is in the tube, remove with a
coat hanger.
fig. 34 If tube is not blocked, look into fan housing. Remove debris with
long-nose pliers, a screwdriver or coat hanger.
©2006 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck Holdings, LLC.
Printed in America
77213-01 REV B
01/06 ECN# R-8018
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|