S I M P L Y
A M A Z I N G ®
USER’S GUIDE
XL2 6 0 5 HH
XL2 2 0 5 RH
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
®
CLEANING SYSTEM
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
Ma int e na nce a nd
Cus t om e r Se rv ice
Your ORECK vacuum cleaner is a product of precise
engineering. The motor bearings are permanently
lubricated and should not be oiled. If you require
additional information or have problems with your
ORECK appliance, or to order new bags or spare
parts, you may call ORECK customer service at:
ACCESSORIES
ITEM
PART N UMBER
1. Dust Bag, 8 Pack, Saniseal®
Hypo-Allergenic
CCPK8DW
CCPK8
Dust Bag, 8 Pack, Regular
2. Belts, 3 Pack
0300604
AIRTABS
0 8 4 5 6 0 3 0 1 5 3
3. Oreck Fresh Air® Tabs
Or write to:
Oreck UK
P.O. Box 201
Exeter
Devon
EX1 1XB
Attention: Oreck Customer Service
Please specify the model number and serial/ code
number which can be found on the data plate on the
back of the vacuum.
Save your sales or purchase slip. Should your
ORECK appliance require warranty service, present
this slip to the Authorized Service Center as your
proof of purchase date.
Wa rra nt y
ORECK MANUFACTURING COMPANY: (Oreck 21180 Johnson Road;
Long Beach, MS, USA 39560 gives you the following warranty for this
product only if it was originally purchased for residential use, not resale
from Oreck or an Oreck Authorized Retail Dealer.)
Oreck will repair or replace, free of charge, to the original purchaser, any
part that is found to be defective in material or workmanship within
three (3) years of date of purchase; ten (10) years on housing. This
warranty applies to normal domestic use. Any commercial use of this
product will void this warranty. This limited warranty covers the revolving
roller brush for one (1) year for residential use only.
This warranty does not cover the replacement of expendable or
consumable parts such as carbon motor brushes, edge brushes, belts,
bulbs, disposable bags and other parts subject to normal wear unless
they are defective in material or workmanship.
This warranty does not apply to any part subjected to accident, abuse,
alteration, misuse, damage caused by act of God, the use of voltages
other than indicated on the serial number displayed on this product or
service of this product by other than Oreck or a participating Factory
Authorized Service Center.
Oreck does not authorize any person or representative to assume or
grant any other warranty obligation with the sale of this product.
Oreck’s warranty is valid only if you retain proof of purchase from Oreck
or an Oreck Authorized Retail Dealer for this product. If you purchase this
product from any other source, your purchase is “AS IS,” which means
Oreck grants you no warranty, and that you, not Oreck, assume the entire
risk of the quality and performance of this product, including the entire
cost of any necessary servicing or repairs of any defects.
This warranty is in addition to your statutory and other legal rights.
*Reconditioned units carry a 6 month warranty from date of purchase.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
To Re pla ce Pa pe r
Filt e r Dus t Ba g
As s e m bly
To assist you in identifying
components of your vacuum,
the parts have been numbered
WARNING: Unplug cord from
electrical outlet before servicing.
10
11
BAG REMO VAL:
9
as follows
:
1
1 Handle tube, upper
2 Tube, lower
3 Power head
4 Outer bag
5 Paper filter dust bag
6 Power cord
7 Retaining spring
8 Bag tension bar
9 Zip fastener
10 On/ off switch
11 Cord hook
12 Plastic loop/ cable clamp
13 Connector assembly
14 Fan housing
12
1. Unsnap bag door from base.
2. Gently pull bag from
cardboard collar upwards.
5
13
4
8
6
2
14
7
15
15 Cord assembly
3
3. XL2605HH: Dust seal will
close automatically
Before assembling appliance,
remove two screws from
connector assembly. Remove
cardboard insert by pulling
upward.
1
BAG IN STALLATIO N :
1. Slide the cardboard collar
completely onto bag dock
door.
With ON/ OFF switch facing
the front of the unit, slide
upper handle section over
matching section of the
2
ENFONCEZ JUSQU’À
ENTENDRE UN BRUIT
PRESIOANE HAST
ESCUCHAR UN
connector assembly. Insert
short screw into top hole and
long screw into bottom hole
then tighten firmly until handle
is no longer loose.
CHASQUIDO DE SUJECI
Attach cord to cord clip by
pressing cord above and below
clip ensuring the cord is fully
rested in clip.
3
2. Firmly push bag dock door
with both thumbs on
indication point until
it snaps.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Ope ra t ing Ins t ruct ions
To O p e ra te
All paper dust bags are not the same. Your ORECK
disposable dust bags have been designed to be used with the
ORECK cleaner. Using bags other than genuine ORECK
TYPE CC disposable bags will affect the cleaning ability of
your cleaner and could cause damage to it.
Make sure the disposable paper filter dust bag is in place.
DO NOT operate the cleaner without a paper filter dust bag.
Plug the power cord into an electrical outlet. Press the ON(l) -
OFF(O) switch on handle assembly when ready to operate.
Ge n e ra l In fo rm a tio n
Th e Be lt
The performance of your new cleaner greatly depends upon
care and maintenance. The instructions in this manual will
guide you in performing basic care and maintenance. To
obtain the most satisfying years of service read the instructions
and keep them handy for future reference.
The belt on your vacuum cleaner controls the speed of the
revolving brush and is very important for the effective
operation of the cleaner. If the belt becomes stretched or cut,
it will cause the revolving brush to stop completely or slow
down. See instructions in the manual for replacing belt.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts.
Belts other than ORECK belts will not operate the revolving
brush correctly and may create undue stress which will cause
damage to the motor and brush bearings. Using belts other
than ORECK belts will void the warranty.
O p e ra tin g Re co m m e n d a tio n s
This new ORECK XL High-Speed Upright is one of the finest,
fastest, and strongest units in its class. You’ll love the way it
cleans, gets under things, and it’s SO lightweight and easy to
use.
The following are a few simple suggestions regarding its
operation:
Lu b rica tio n
The vacuum cleaner motor bearings are factory lubricated
and sealed. Further lubrication is not required.
1. When inserting a new disposable paper filter dust bag—
FIRST PUFF OUT and OPEN THE BAG.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or
makes an unusual noise, STOP OPERATION and service.
4. Although your upright will pick up pins, paper clips, and
other small objects, it is recommended that these be
removed from the floor before you vacuum. Failure to do
so may result in permanent damage to the motor suction
fan and its housing.
5. WARN IN G: Do not use your vacuum cleaner on damp
or wet surfaces. This will cause damage to the vacuum
cleaner and is dangerous to the user. Damage caused by
use on wet or damp surfaces is not covered under
warranty.
Ge n e ra l Cle a n e r Ca re
At least once a month, check
for and remove excessive lint,
string or hair from revolving
brush.
Wipe the outside of the
cleaner with a damp cloth.
Also clean the connector
deflector assembly area, base
of cleaner and fan housing
area. If there is dust in the
outer bag, vacuum it or shake
it out.
6. REPLACE THE BELT EVERY 6 MONTHS.
7. Change the disposable filter dust bag at least once a
month—even if it is not full! The collected dust in the dust
bag can cause odor, attract moisture, act as a breeding
area and can affect the efficiency of the cleaner.
8. DO NOT run the va cuum clea ner over cord. The
revolving brush could da ma ge the cord.
A little preventative maintenance will keep your cleaner
looking new and will ensure continued cleaning effectiveness.
CAUTIO N —Wo o d Flo o rs, So ft (Vin y l, Asp h a lt Tile ,
e tc.) Flo o r Su rfa ce s a n d Po lish e d Flo o r Fin ish e s
Use floor and floor finish manufacturer’s recommended
methods of cleaning. The metal strip on the base of the
cleaner could be damaged if used on concrete or abrasive
surfaces, and, therefore, cause damage to wood floors, soft
(vinyl, asphalt tile, etc.) floor surfaces and polished floor
finishes. The roller brush may also scuff very soft finishes. Do
not operate the unit while in the upright and locked position.
Do not let the unit run while in any one stationary position for
any period of time. Keep the unit moving while in operation.
9. Use ca ution when va cuuming over a rea rug edges a nd
fringe.
Disp o sa b le Pa p e r Filte r Du st Ba g s
Disposable paper filter dust bags play a very important role
in the efficiency of your ORECK vacuum cleaner. The purpose
of the paper bag is to trap dirt, but at the same time it must
be porous enough to allow air to pass through. If the paper
bag becomes clogged, no air can pass through the cleaner
and cleaning cannot take place, regardless of the cleaner’s
power.
Ce lo c® Hy p o -Alle rg e n ic Filte r Sy ste m : XL2 6 0 5 HH
The CELOC SMMS outer bag of your vacuum cleaner is high
filtration medical material designed to filter the smallest of
dust particles. It is important the inside of the outer bag be
cleaned. Vacuum the inside of the outer bag or hand wash,
turned inside out, with warm water, and air dry. For best
results, the CELOC SMMS outer bag should be replaced
once a year. The CELO C la yered disposa ble inner dust ba g
must be repla ced once a month even if it is not full.
Cha nge it more often if it is used in extremely dirty a rea s.
Increase the cleaning power of your vacuum by changing the
bag often.
To keep your cleaner operating at maximum efficiency,
change the dust bag frequently. DO NOT FILL ABOVE THE
LINE INDICATED ON THE DUST BAG.
Be sure the disposable paper filter dust bag is installed
properly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
How t o Re pla ce a Worn Be lt
To Adjus t or Re pla ce Brus h
WARNING: Unplug cord from
WARNING: Unplug cord from
electrical outlet before servicing.
electrical outlet before servicing.
Remove the replacement
belt from the storage
channel.
To determine if the brush is
worn, place a firm straight
edge across the nozzle
opening. If brush bristles
do not extend beyond
baseplate, brush should be
adjusted.
Remove the baseplate by
removing 5 screws. Then,
remove the belt and brush
roll from the housing.
Remove the door by
removing the hold down
screw located on side of
power head.
Rotate both bearing
assemblies at ends of
brush roll to show “OLD”
and replace in the holding
channels in the housing.
Slide the door forward
by prying open with a
screwdriver or coin.
NOTE: The bearing
assembly setting marked
“OLD” has a smooth side.
The one marked “NEW”
has notches. When
rotating bearings, make
Remove the belt from the
brush roll pulley and the
motor drive shaft.
Rota te a nd ma tch
bea ring a ssemblies
sure both bearing
assembly settings are the
same and face up when
replacing the brush roll.
Loop the new belt over
the motor drive shaft.
Place the opposite end of
the belt on the brush roll
pulley.
Reassemble the belt and
the baseplate and check
bristle height above
baseplate at each end of
brush.
Rotate the brush roll three
(3) complete revolutions
to ensure that no part of
the belt is overhanging
the end of the motor
drive shaft.
If a previous adjustment
has already been made
and bristle height does not
extend above baseplate, a
new brush assembly
IMPO RTAN T: Un le ss
th e b ru sh is w o rn a s
in d ica te d a b o ve ,
b o th b e a rin g s m u st
b e in th e “ N EW ”
p o sitio n . W h e n
should be ordered.
Replace the door by
sliding it into the groove
at the bottom of the
housing. Replace the
hold down screw.
ro ta tin g , b o th
b e a rin g s m u st b e in
th e “ O LD” p o sitio n .
Un m a tch e d se ttin g s
w ill ca u se d a m a g e
to y o u r m a ch in e .
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Many times blockage occurs
due to a full dust bag
F
St uf f ing or Blocka ge
causing dirt to back down
the air flow system. When
that happens, the blockage
will be at the top of the
system, starting in the area
where the dust bag connects
to the connector assembly.
See illustration F.
Connector
Deflector
Opening
Under certain conditions it is possible to stuff or block the intake
tube and the lower tube assembly. If your vacuum cleaner does
not pick up properly, or makes unusual noise and the outer bag
does not fluff up or balloon open, follow the following steps:
WARNING: Unplug cord from electrical
outlet before servicing.
1. Check for blockage at the
mouth of the intake
opening. See illustration A.
If there is blockage, remove
it with long-nose pliers, a
screwdriver or coat hanger.
If you can not reach the
blockage, remove
N O TE: If the “Stuffing or Blockage” actions do not correct the
problem, contact an ORECK authorized service center or call the
customer service center at: 0 8 4 5 6 0 3 0 1 5 3 .
A
B
Intake Opening
baseplate. See illustration B.
2. If the blockage is not at the
base, remove lower tube.
See illustration C. Unhook
retainer spring, releasing
bottom of bag. Twist lower
collar counterclockwise to
slide up. Pull tube out of
base. Check for blockage.
If blockage is in the tube,
remove with a coat hanger.
3. If tube is not blocked, look
into fan housing. See illus-
tration D. Remove debris
with long-nose pliers, a
IMPORTANT: On plush and new carpets, stuffing may occur
due to excessive fuzz and loose cuttings in the carpet.
Stuffing could occur for the first few cleanings until all the
loose material is removed. Due to the high efficiency of the
cleaner, many older carpets will cause stuffing when the
cleaner is first used on them.
Intake Opening
Retainer
Spring
®
Us ing An Ore ck Fre s h Air Ta b
screwdriver or coat hanger.
4. To reassemble, check O-ring
on tube, and replace if
Your ORECK XL vacuum
cleaner has a special
Oreck Fresh Air® tab
pocket. This pocket is
located inside the outer
bag in the area where the
disposable paper bag
attaches to the intake
tube. Insert tablet in
pocket.
damaged. Vacuum will not
operate properly without the
tube O-ring. Slide O-ring to
approximately 2" from base
of tube. Replace tube by
first lining up slot at base of
tube with inner tab inside
fan housing. Then reinsert
tube and push down until
the tube is seated. Make
sure O-ring is in place
C
Fan
Housing
O-ring
against fan housing
opening. Replace and
D
tighten collar until collar
locking tabs are locked in
place. See illustration E.
Make sure collar is not cross
threaded on housing.
E
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble s hoot ing Guide
WARNING: Unplug cord from
electrical outlet before servicing.
SAVE SERVICE CALLS...CHECK THESE FIRST:
•
•
•
Is the disposable filter dust bag full?
Are pores of filter dust bag clogged with powder or fine dust?
Is anything clogging the revolving brush, lower tube, intake
opening, fan housing or connector assembly opening?
Is the belt in place and turning the brush?
Are the brush ends in the proper location?
Does the brush turn freely? Are hair, string or rug fibers wound
around the brush?
•
•
•
PROBLEM
POSSIBLE SOURCE
AREAS TO CHECK
CLEAN ER
W ILL N O T RUN
Not plugged in
properly.
Be sure cleaner is
firmly plugged
into wall outlet.
No electricity in
wall outlet.
Check electrical
source–fuse or
circuit breaker.
CLEAN ER
DO ES N O T PICK UP
Filter bag is full.
Replace filter bag.
See “To Replace
Paper Filter Dust
Bag.”
Nozzle or intake
pivot clogged.
Clear obstruction.
Belt is broken or
stretched.
Replace belt.
Brush is worn.
See “To Adjust or
Replace Brush.”
Bag tube clogged. Clear obstruction.
Bag pores are
clogged with fine
dust.
Change bag.
Impeller fan is
broken.
Return to Service
Center for repair.
Revolving brush is Check brush roll
not even at both
ends.
end cards. Make
sure words “OLD”
or “NEW” match
at each end.
ALL O THER SERVICIN G SHO ULD BE DO N E BY AN
O RECK AUTHO RIZED SERVICE CEN TER.
CALL CUSTOMER SERVICE HOT LINE
0845 603 0153
Whenever calling, please be sure to have your model and
serial number from data plate.
©2005 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck
Holdings, LLC. Printed in America.
7 5 3 1 6 -0 8 REV A
8
0 8 / 0 5 ECN # R-7 8 7 3
Download from Www.Somanuals.com. All Manuals Search And Download.
|