S I M P L Y
A M A Z I N G ®
USER’S GUIDE
U2 6 3 0 HH
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
E
N
G
L
I
S
H
BEFORE OPERATING CLEANER,
READ ALL INSTRUCTIONS IN
THIS MANUAL CAREFULLY.
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical appliance, basic
precautions should always be followed,
including the following:
Table of Contents
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER
Maintenance and Customer Service, Polarized Plug Notice,
Accessories, Important Safety Instructions . . . . . . . . . . . . . . . page
2
WARNING
To reduce the risk of fire,
electric shock, or injury:
Warranty, Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . page
3
Parts List, Assembly, Operating Instructions,
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page
4
To Replace Filter Dust Bag, How to Replace a Worn Belt,
To Adjust or Replace Brush, Using an Oreck Fresh Air® Tab,
Stuffing or Blockage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page
• Do not leave appliance unattended when plugged in.
Unplug from outlet when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Do not operate the unit while in the upright and locked
position.
• Do not let the unit run while in any one stationary position
for any period of time. Keep the unit moving while in
operation.
5
Maintenance and Customer Service
Your Oreck vacuum cleaner is a product of precise engineering. The
motor bearings are permanently lubricated and should not be oiled. If
you require additional information or have problems with your Oreck
appliance, you may call ORECK customer service at:
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
US: 1-800-989-3535 Canada: 1-888-676-7325
• Use only as described in this manual. Use only
manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not
working as it should, has been dropped, damaged, left
outdoors, or dropped into water, return it to a service
center or call customer service at: US: 1-800-989-3535
Canada: 1-888-676-7325
Please specify the model number and serial/code number which can be
found on the data plate on the back of the vacuum.
Save your sales or purchase slip. Should your Oreck appliance require
warranty service in the U.S.A., present this slip to the Authorized Service
Center as your proof of purchase date or, in Canada, call customer
service.
• Do not pull or carry by cord, use cord as a handle, close
door on cord, or pull cord around sharp edges or corners.
Keep cord away from heated surfaces.
Polarized Plug Notice
• Do not run appliance over cord.
This product is equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact an electrician to replace the obsolete outlet.
Do not defeat the purpose of the polarized plug.
• Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair and anything
that may reduce air flow.
• Keep hair, loose clothing, fingers and all parts of body
away from openings and moving parts.
• Do not use to pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
• Do not use without filter bag assembly in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids,
such as gasoline or lighter fluid, or use in areas where
they may be present.
• Do not use appliance in an enclosed space where
flammable, explosive or toxic vapors are given off by oil
base paint, paint thinner, some mothproofing substances,
or in an area where flammable dust is present.
• Do not pick up toxic material such as chlorine bleach,
drain cleaner, gasoline, etc. with this appliance.
• Use caution when vacuuming over area rug edges and
fringe.
Accessories (Sold Separately)
USA: 1-800-989-3535 CANADA: 1-888-676-7325
ITEM
PART #
CCPK8DW
CCPK8
0300604
AIRTABS
0300604
00965-0019
1. Dust Bag, 8 Pack Saniseal®, Hypo-Allergenic
Dust Bag, 8 Pack, Regular
2. Belts, 3 Pack
3. Oreck Fresh Air® Tabs
4. Belts, 3 Pack
5. Light Bulb
SAVE THESE INSTRUCTIONS
Household Use Only
2
Download from Www.Somanuals.com. All Manuals Search And Download.
E
N
G
L
I
S
H
Warranty
Troubleshooting Guide
ORECK MANUFACTURING COMPANY: (Oreck Manufacturing
Company gives you the following limited warranty for this product only if
it was originally purchased for residential use, not resale, from Oreck or
an Oreck Authorized Retail Dealer.)
WARNING: Unplug cord from electrical
outlet before servicing.
SAVE SERVICE CALLS...CHECK THESE FIRST:
Oreck will repair or replace, free of charge, to the original purchaser, any
part which is found to be defective in material or workmanship within one
(1) year of the date of purchase; ten (10) years on housing. This limited
warranty applies to normal domestic use. Any commercial use of this
product will void this limited warranty. This limited warranty covers the
revolving roller brush for one (1) year for residential use only.
•
Is the disposable filter dust bag full?
• Are pores of filter dust bag clogged with powder or fine dust?
• Is anything clogging the revolving brush, lower tube, intake opening,
fan housing or connector assembly opening?
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location?
This limited warranty does not cover the replacement of expendable or
consumable parts such as carbon motor brushes, edge brushes, drive
belts, bulbs, disposable bags and other parts subject to normal wear
unless they are defective in material or workmanship.
• Does the brush turn freely? Are hair, string or rug fibers wound around
the brush?
PROBLEM
POSSIBLE SOURCE
AREAS TO CHECK
This limited warranty does not apply to any part subjected to accident,
abuse, commercial use, alteration, misuse, damage caused by act of
God, the use of voltages other than indicated on the serial number
displayed on this product or service of this product by other than Oreck or
a participating Factory Authorized Service Center.
Not plugged in
properly.
Be sure cleaner is
firmly plugged into
wall outlet.
CLEANER
WILL NOT RUN
No electricity in wall
outlet.
Check electrical
source–fuse or
circuit breaker.
Oreck does not authorize any person or representative to assume or
grant any other warranty obligation with the sale of this product.
Oreck’s limited warranty is valid only if you retain proof of purchase from
Oreck or an Oreck Authorized Retail Dealer for this product. If you
purchase this product from any other source, your purchase is “AS IS,”
which means Oreck grants you no warranty, and that you, not Oreck,
assume the entire risk of the quality and performance of this product,
including the entire cost of any necessary servicing or repairs of any
defects.
CLEANER
DOES NOT PICK UP
Filter bag is full.
Replace filter bag. See
“To Replace Filter
Dust Bag.”
Nozzle or intake
pivot clogged.
Clear obstruction.
Oreck’s liability for damages to you for any costs whatsoever arising out
of this statement of limited warranty shall be limited to the amount paid for
this product at the time of original purchase, and Oreck shall not be liable
for any direct, indirect, consequential or incidental damages arising out of
the use or inability to use this product.
Belt is broken or
stretched.
Replace belt.
Brush is worn.
See” To Adjust
or Replace Brush.”
Some states do not allow the exclusion or limitation of incidental or conse-
quential damages, so the above limitation or exclusion may not apply to
you.
Bag tube clogged.
Clear obstruction.
Change bag.
Bag pores are
clogged with fine
dust.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND
Impeller fan is
broken.
Return to Service
Center for repair.
FITNESS FOR
A
PARTICULAR PURPOSE, ARE LIMITED IN
DURATION TO THE WARRANTY PERIOD, AND NO WARRANTIES,
WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THIS
PERIOD.
Revolving brush is
not even at both
ends.
Check brush roll end
cards. Make sure
words “OLD” or
“NEW” match at
each end.
Some states do not allow limitations on the duration of implied warranties,
so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
CALL CUSTOMER SERVICE HOT LINE
US: 1 - 8 0 0 - 9 8 9 - 3 5 3 5 Ca n a d a : 1 - 8 8 8 - 6 7 6 - 7 3 2 5
Whenever calling, please be sure to have your model and serial
number from data plate.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
E
N
G
L
I
S
H
5. WARNING: Do not use your vacuum cleaner on damp or wet
surfaces. This will cause damage to the vacuum cleaner and is
dangerous to the user. Damage caused by use on wet or damp
surfaces is not covered under warranty.
Parts List
To assist you in identifying components of your vacuum, the parts have
been numbered as follows:
6. REPLACE THE BELT EVERY 6 MONTHS.
10
7. Change the disposable filter dust bag at least once a month—
even if it is not full! The collected dust in the dust bag can cause
odor, attract moisture, and can affect the efficiency of the cleaner.
1
2
3
4
5
6
7
8
9
Handle section, upper
Tube, lower
Power head
Outer bag
Filter dust bag
Power cord
Retaining spring
Bag tension bar
Zip fastener
11
9
1
8. DO NOT run the vacuum cleaner over the cord. The revolving
brush could damage the cord.
9. Use caution when vacuuming over area rug edges and fringe.
4
General Information
5
12
10 On/off switch
11 Cord hook
12 Connector assembly
13 Fan housing
The performance of your new cleaner greatly depends upon care and
maintenance. The instructions in this manual will guide you in
performing basic care and maintenance. To obtain the most satisfying
years of service read the instructions and keep them handy for future
reference.
2
6
14 Cord Assembly
14
Disposable Paper Filter Dust Bags
13
7
8
Disposable paper filter dust bags play a very important role in the
efficiency of your ORECK vacuum cleaner. The purpose of the paper
bag is to trap dirt, but at the same time it must be porous enough to
allow air to pass through. If the paper bag becomes clogged, no air can
pass through the cleaner and cleaning cannot take place, regardless of
the cleaner’s power.
3
Assembly
fig. 1 Before assembling appliance, remove two screws from the
connector assembly. Remove cardboard insert by pulling
upward.
To keep your cleaner operating at maximum efficiency, change the dust
bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE
DUST BAG.
fig. 2 Slide upper handle section over the matching section of the
Be sure the disposable paper filter dust bag is installed properly.
connector assembly. Insert short screw into top hole and long
screw into the bottom hole then tighten firmly until handle is no
longer loose.
All paper dust bags are not the same. Your ORECK disposable
dust bags have been designed to be used with the ORECK cleaner.
Using bags other than genuine ORECK Type CC disposable bags
will affect the cleaning ability of your cleaner and could cause
damage to it.
Operating Instructions
The Belt
The belt on your vacuum cleaner controls the speed of the revolving
brush and is very important for the effective operation of the cleaner. If
the belt becomes stretched or cut, it will cause the revolving brush to
stop completely or slow down. See instructions in the manual for
replacing belt.
Make sure disposable paper filter dust bag is in place. DO NOT operate
the cleaner without a paper filter dust bag. Plug the power cord into an
electrical outlet and press the On (l) - OFF (O) switch on top of base
when ready to operate.
Up-Position Lock
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts. Belts
other than Oreck belts will not operate the revolving brush
correctly and may create undue stress which will cause damage to
the motor and brush bearings. Using belts other than ORECK belts
will void the warranty.
fig. 3 Place foot on power head and lean handle back gently to release
lock for vacuum use. Return handle to the full upright position to
engage lock.
NOTE: Do not operate the unit while in the upright and locked position.
Do not let the unit run while in any one stationary position for any period
of time. Keep the unit moving while in operation.
Lubrication
For Easy Power Cord Storage
The vacuum cleaner motor bearings are factory lubricated and sealed.
Further lubrication is not required.
fig. 4 Wrap power cord around cord hook on handle and cord hook on
connector. Secure to "U" shaped part on plug.
General Cleaner Care
Operating Recommendations
At least once a month, check for
and remove excessive lint, string or
hair from revolving brush.
This new ORECK XL High Speed Upright is one of the finest, fastest,
and strongest units in its class. You’ll love the way it cleans, gets under
things, and it’s SO lightweight and easy to use.
Wipe the outside of the cleaner with
a damp cloth. Also clean the
The following are a few simple suggestions regarding its operation:
connector deflector assembly area,
base of cleaner and fan housing
area. If there is dust in the outer
bag, vacuum it or shake it out.
1. When inserting a new disposable paper filter dust bag—FIRST
PUFF OUT and OPEN THE BAG.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or makes an
unusual noise, STOP OPERATION and service.
A little preventative maintenance
will keep your cleaner looking new
and will ensure continued cleaning
effectiveness.
4. Although your upright will pick up pins, paper clips, and other small
objects, it is recommended that these be removed from the floor
before you vacuum. Failure to do so may result in permanent
damage to the motor suction fan and its housing.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
E
N
G
L
I
S
H
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor
Surfaces and Polished Floor Finishes
IMPORTANT: Unless the brush is worn as indicated above, both
bearings must be in the “NEW” position. When rotating, both
bearings must be in the “OLD” position. Unmatched settings will
cause damage to your machine.
Use floor and floor finish manufacturer’s recommended methods of
cleaning. The metal strip on the base of the cleaner could be damaged
if used on concrete or abrasive surfaces, and, therefore, cause damage
to wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished
floor finishes. The roller brush may also scuff very soft finishes. Do not
operate the unit while in the upright and locked position. Do not let the
unit run while in any one stationary position for any period of time. Keep
the unit moving while in operation.
®
Using An Oreck Fresh Air Tab
fig. 19 Your ORECK XL vacuum cleaner has a special Oreck Fresh
Air® tab pocket. This light-colored pocket is located inside the
vinyl bag in the area where the paper disposable bag attaches
to the intake tube. Insert tablet in pocket if desired.
To Replace Filter Dust Bag
Stuffing or Blockage
WARNING: Unplug cord from electrical
outlet before servicing.
IMPORTANT: On plush and new carpets, stuffing may occur inside the
the intake tube and the lower tube assembly. This is due to excessive
fuzz and loose cuttings in the carpet. Stuffing could occur for the first few
cleanings until all the loose material is removed. Due to the high efficiency
of the cleaner, many older carpets will cause stuffing when the cleaner is
first used on them. If your vacuum cleaner does not pick up properly, or
makes unusual noise and the outer bag does not fluff up or balloon open,
follow these steps:
BAG REMOVAL:
fig. 5 Unzip outer bag completely.
fig. 6 Pull bag cardboard collar to release bag dock door from
connector. Bag dock door will hinge downward.
fig. 7 Gently pull bag cardboard collar upward out of the bag dock.
BAG INSTALLATION:
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 8 Slide the cardboard collar completely onto bag dock door.
fig. 9 Firmly push bag dock door with both thumbs on indication point
fig. 20 Check for blockage at the mouth of the intake opening. If there
is blockage, remove it with long-nose pliers, a screwdriver or
coat hanger. If you can not reach the blockage, remove
baseplate (fig. 21).
until it snaps.
How to Replace a Worn Belt
fig. 22 If the blockage is not at the base, remove lower tube. Unhook
WARNING: Unplug cord from electrical
outlet before servicing.
retainer spring, releasing bottom of bag.
fig. 23 Twist lower collar counterclockwise to slide up. Pull tube out of
base.
fig. 10 Remove the replacement belt from the storage channel.
fig. 24 Check for blockage. If blockage is in the tube, remove with a
fig. 11 Remove the door by removing the hold down screw located on
coat hanger.
side of power head.
fig. 25 If tube is not blocked, look into fan housing. Remove debris
fig. 12 Slide the door forward by prying open with a screwdriver or coin.
with long-nose pliers, a screwdriver or coat hanger.
fig. 13 Remove the belt from the motor drive shaft and brush roll pulley.
fig. 23 To reassemble, check O-ring on tube, and replace if damaged.
Vacuum will not operate properly without the tube O-ring. Slide
O-ring to approximately 2" from base of tube. Replace tube by
first lining up slot at base of tube with inner tab inside fan
housing. Then reinsert tube and push down until the tube is
seated. Make sure O-ring is in place against fan housing
opening. Replace and tighten collar until collar locking tabs are
locked in place.
fig. 14 Loop the new belt over the motor drive shaft. Place the
opposite end of the belt on the brush roll pulley. Rotate the
brush roll three (3) complete revolutions to ensure that no part
of the belt is overhanging the end of the motor drive shaft.
fig. 12 Replace the door by sliding it into the groove at the bottom of
the housing.
fig. 11 Replace the hold down screw and tighten.
fig. 26 Make sure collar is not cross threaded on housing. Reattach
To Adjust or Replace Brush
bag spring (fig. 22).
fig. 27 Many times blockage occurs due to a full dust bag causing dirt to
back down the air flow system. When that happens, the
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 15 To determine if the brush is worn, place a firm straight edge
across the nozzle opening. If brush bristles do not extend
beyond baseplate, brush should be adjusted.
blockage will be at the top of the system, starting in the area
where the dust bag connects to the connector assembly.
NOTE: If the above actions do not correct the problem, contact an
Oreck authorized service center or call the customer service center.
US: 1-800-989-3535 Canada: 1-888-676-7325
fig. 16 Remove the baseplate by removing 5 screws.
fig. 17 Remove the belt and brush roll from the housing.
fig. 18 Rotate both bearing assemblies at ends of brush roll to show
"OLD" and replace in the holding channels in the housing.
NOTE: The bearing assembly setting marked "OLD" has no ribs on the
top of the assembly. The one marked "NEW" has several ribs. When
rotating bearings, make sure both bearing assembly settings are the
same and face up when replacing the brush roll.
fig. 15 Reassemble the belt and the baseplate and check bristle height
above baseplate at each end of brush.
If a previous adjustment has already been made and bristle height does
not extend above baseplate, a new brush assembly should be ordered.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7 5 8 0 5 -0 1 REV A
1 2 / 0 8 ECN # R-9 2 6 5
©2008 Oreck Holdings, LLC. All Rights Reserved. All word marks, logos, regestered trademarks and product configurations are
owned and used under the authority of Oreck Holdings, LLC.
Download from Www.Somanuals.com. All Manuals Search And Download.
|