Oreck Vacuum Cleaner BB1005 User Manual

®
S I M P L Y  
A M A Z I N G  
USERS GUIDE  
COMPACT  
CANISTER  
VACUUMS  
BBB1005  
•IMPORTANT•  
SAVE THIS BOOKLET!  
Includes:  
• Safety Warnings  
• Parts List  
• Operating Instructions  
• Maintenance  
• Warranty  
• Trouble Diagnosis  
• Accessories List  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The fuse carrier is red and hinged to the plug. Do not use the plug  
if it is different.  
BEFORE OPERATING  
CLEANER, READ ALL  
INSTRUCTIONS IN THIS  
MANUAL CAREFULLY.  
If necessary, you may contact customer service for replacement  
fuse covers.  
MOTOR PROTECTION SYSTEM: If fine materials such as soot,  
cement, plaster dust, copy machine powder, etc. are picked up,  
the bag surface may seal and cause the motor to shut off to  
avoid over-heating. If this happens, turn the switch off then turn  
off the wall socket and/or unplug the cleaner. Replace filter bag.  
Check and clear any clogs in hose or accessories. After  
approximately 30 min. the motor will have cooled and the cleaner  
will be ready to use.  
Table of Contents  
Note: The cleaner must remain unplugged for 30 minutes  
for motor to cool and system to reset.  
Safeguards, Important Electrical Information,  
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . page 5-2  
Warranty, Parts List, Accessories . . . . . . . . . . . . . . . . . page 5-3  
IMPORTANT  
Assembly, Polarized Plug Notice, To Operate,  
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5-4  
SAFETY INSTRUCTIONS  
When using an electrical appliance, basic  
precautions should always be followed,  
including the following:  
Maintenance & Customer Service,  
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . page 5-5  
READ ALL INSTRUCTIONS BEFORE  
USING THIS VACUUM CLEANER  
Safeguards  
WARNING  
WARNING: Unplug cord from electrical  
outlet before servicing.  
To reduce the risk of fire,  
electric shock, or injury:  
IMPORTANT: Make sure filter bag is in place. Do not operate  
cleaner without filter bag. Damage to motor may occur.  
• Do not leave appliance unattended when plugged in.  
Unplug from outlet when not in use and before servicing.  
• Be sure bag gasket is in place. If the white bag gasket is  
damaged or lost, replace at once.  
• Do not use outdoors or on wet surfaces.  
• Do not allow to be used as a toy. Close attention is  
necessary when used by or near children.  
• For best results, change disposable filter bag regularly even if  
it is not completely full. An extremely dirty bag or a bag close  
to full will affect the suction of the cleaner and can create  
excessive motor heat that could damage the motor. A good  
practice is to change filter bag every 30 days even if it is not full.  
• Use only as described in this manual.  
• Do not use with damaged cord or plug. If appliance is not  
working as it should, has been dropped, damaged, left  
outdoors, or dropped into water, return it to a service  
center or call customer service at: 0845 603 0153.  
• Do not pick up moist material or liquids.  
• Clean your vacuum cleaner with a damp (not wet) cloth in the  
disposable bag cavity and the outside of canister unit.  
• Do not pull or carry by cord, use cord as a handle, close  
door on cord, or pull cord around sharp edges or corners.  
Do not run appliance over cord. Keep cord away from  
heated surfaces.  
IMPORTANT: DO NOT REMOVE the dirt retaining flap  
attached on the back of the front plate. It must be left in place  
for the unit to operate properly and to ensure cleaning  
effectiveness.  
• Do not unplug by pulling on cord. To unplug, grasp the  
plug, not the cord.  
• Do not handle plug or appliance with wet hands.  
• Do not put any object into openings. Do not use with any  
opening blocked; keep free of dust, lint, hair and anything  
else that may reduce air flow.  
Important Electrical Information  
The wires in the main lead are coloured in accordance with the following  
code:  
• Keep hair, loose clothing, fingers and all parts of body  
away from openings and moving parts.  
Blue - Neutral  
Brown - Live  
• Do not use to pick up anything that is burning or smoking,  
such as cigarettes, matches, or hot ashes.  
If the colours of the wires in the main lead of this appliance do not  
correspond with the coloured markings identifying the terminals in your  
plug, proceed as follows:  
• Do not use without filter bag assembly in place.  
• Turn off all controls before unplugging.  
• Use extra care when cleaning on stairs.  
The wire which is coloured blue must be connected to the terminal  
marked with the letter N or coloured black. The wire coloured brown  
must be connected to the terminal marked with the letter L or coloured  
red. Do not make any connection to the terminal marked E or or  
coloured green and yellow.  
• Do not use to pick up flammable or combustible  
liquids, such as gasoline, or use in areas where they may  
be present.  
This appliance is double insulated and no earth connection is necessary.  
If you remove the plug from power supply cord, dispose of it. A  
shock hazard could result if incorrect plug is inserted into a 13  
AMP socket outlet.  
SAVE THESE INSTRUCTIONS  
When changing fuse, use 5 AMP or same size replacement  
fuse.  
Household Use Only  
2
Never use the plug without the fuse cover fitted in place.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warranty  
Parts List  
ORECK MANUFACTURING COMPANY: (Oreck Manufacturing Company,  
21180 Johnson Road; Long Beach, MS, USA 39560, gives you the  
following limited warranty for this product only if it was originally purchased  
for residential use, not resale from Oreck or an Oreck Authorized Retail  
Dealer.)  
1
Oreck will repair or replace, free of charge, to the original purchaser, any  
part that is found to be defective in material or workmanship within three  
(3) years of the date of purchase; ten (10) years on housing. This limited  
warranty applies to normal domestic use. Any commercial use of this  
product will void this limited warranty.  
6
This limited warranty does not cover the replacement of expendable or  
consumable parts such as belts, brushes, bulbs, disposable bags and  
other parts subject to normal wear unless they are defective in material or  
workmanship.  
4
8
This limited warranty does not apply to any part subjected to accident,  
abuse, commercial use, alteration, misuse, damage caused by act of God,  
the use of voltages other than indicated on the serial number displayed on  
this product or service of this product by other than Oreck or a  
participating Factory Authorized Service Center.  
2
3
10  
Oreck does not authorize any person or representative to assume or grant  
any other warranty obligation with the sale of this product.  
5
7
Oreck’s limited warranty is valid only if you retain proof of purchase from  
Oreck or an Oreck Authorized Retail Dealer for this product. If you  
purchase this product from any other source, your purchase is “AS IS,”  
which means Oreck grants you no warranty, and that you, not Oreck,  
assume the entire risk of the quality and performance of this product,  
including the entire cost of any necessary servicing or repairs of any  
defects.  
9
1. Adjustable shoulder strap  
2. Long, extendable, flexible hose  
3. Crevice tool  
This warranty in addition to your statutory and other legal rights.  
4. Upholstery tool  
5. Horsehair bare floor and wall tool  
6. Horsehair dusting brush  
7. Adjustable extension wand  
8. On-board tool caddy  
9. Paper filter bags  
*Reconditioned units carry a 6 month warranty from date of  
purchase.  
10. Tool adapter tube for fitting tools directly to vacuum when  
not using hose.  
G
HEPA filter (not shown)  
G
Scent cartridge (not shown)  
Accessories (Sold Separately)  
Replacement Hypo-Allergenic Filter  
Bags (12 pk. with 1 Micro Filter)  
Replacement Micro Filter  
Replacement HEPA Filter  
Part No. PKBB12DW  
Part No. 72005-01  
Part No. HF1000  
Replacement White Bag  
Gasket  
Part No. 72017-02  
Wheel Kit  
Part No. 09-73069-01  
Part No. CADDYBB  
Vinyl Tool Rack  
Fresh Air® Scent Cartridges  
Notes of Vanilla® 8pk.  
Part No. FA1PK  
Part No. FA2PK  
Part No. FA3PK  
Spring Mullberries® 8pk.  
Blooming Jasmine® 8pk.  
To order new parts or accessories call:  
0845 603 0153  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
For Easy Cord Storage  
Assembly  
fig. 12 Wrap cord around the cord wrap and cord dump located  
on bottom of the canister. To release cord, twist the cord  
dump.  
IMPORTANT: DO NOT  
REMOVE the dirt  
retaining flap  
Blower Port  
attached on the  
back of the front  
plate. It must be left  
in place for the unit  
to operate properly  
and to ensure  
fig. 13 Remove HEPA Filter cover and filter at back of machine.  
Firmly insert flexible hose into blower port.  
Maintenance  
WARNING: Unplug cord from electrical  
outlet before servicing.  
cleaning  
effectiveness.  
Changing the Filter Bag  
Attach Caddy and Insert Tools  
fig. 14  
Use only genuine ORECK XL filter bags. Stand unit on  
its back. Twist knob counterclockwise to release and  
lift out front plate.  
fig. 1 Locate caddy clip slots at top rear corners of canister  
handle. Place appliance on firm, non-slip surface or hold  
in your lap. Grasp handle firmly. Place one of caddy clip  
tabs inside slot on one side of handle and stretch the  
other tab around handle until the opposite tab inserts in  
slot.  
fig. 15 Remove used bag and insert fresh bag. The cardboard  
rim fits smoothly into the recessed top. Align tabs on  
front plate with slots in housing and replace the front  
plate. Close unit by turning knob clockwise.  
fig. 2 Insert crevice tool, brush and fabric tool into caddy in  
fig. 16 IMPORTANT: The white bag gasket glued in the housing  
must be in place or unit will not operate properly.  
Replace if needed.  
spaces provided.  
fig. 3 Caddy will lift up 90° to allow access to the HEPA filter  
cover.  
NOTE: The disposable inner filter bag must be replaced once a  
month even if it is not full. Change it more often if it is  
used in extremely dirty areas. Increase the cleaning  
power of your vacuum by changing the bag often.  
Attach Shoulder Strap  
fig. 4 Clamp one end of shoulder strap in front slot located at  
front of handle.  
Replacing the Micro Filter  
fig. 5 Clamp opposite end of shoulder strap in slot at back of  
handle.  
Remove filter bag by following the Changing the Filter Bag  
instructions.  
fig. 6 Adjust length by pulling strap through clip.  
fig. 17 Remove old micro filter from bottom inside unit. Replace  
IMPORTANT: Before using shoulder strap, pull both ends to be  
sure it is secure.  
with new filter.  
NOTE: A replacement filter is supplied in each package of 12  
ORECK XL filter bags or you may order filters separately.  
To Operate  
Using a HEPA-Filter and Scent Cartridge  
fig. 18 Remove HEPA Filter cover at back of machine by  
pressing down in top slot and folding back the cover. Lift  
cover to remove.  
Plug cord into electrical outlet.  
Power Switch  
fig. 19 Insert Fresh Air® Scent Cartridge on tab located in center  
fig. 7 Push power switch to “ON” (I) position.  
of the filter cover.  
Hose and Tool Installation  
fig. 20 Place the HEPA Filter in the filter cover.  
fig. 8 The flexible hose uses a Shurlock® locking system that  
prevents hose removal unless intended. To install hose,  
align “J” slot in hose coupling with tab inside the suction  
port. Insert hose into suction port. Twist collar clockwise  
to lock hose coupling in port. Twist counterclockwise and  
pull to remove hose.  
fig. 18 Replace the HEPA Filter assembly on the canister by  
placing the bottom lip of the cover in the inside slot of  
the canister and closing the cover until the top latch is  
locked.  
NOTE: It is recommended to replace the scent cartridge when  
fig. 9 The adjustable extension wand and cleaning tools  
supplied with your Oreck XL Compact Canister Vacuum  
lock together with friction. Twist and push to be sure they  
lock tightly when installing. Twist and pull to remove.  
the inner filter bag is replaced.  
Replace the HEPA filter every 6 months. Replace more  
often if vacuum is used to pick up fine particles or in  
extremely dirty areas.  
fig.10 When installing tools directly to blower or suction port  
without using hose, tool adapter tube must be used.  
Adjustable Extension Wand  
fig. 11 To adjust extension wand, press release button and pull  
inner tube to desired length. Tube will lock when button  
is released. To shorten length, press release button and  
push inner tube.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance and Customer Service  
Your ORECK COMPACT CANISTER VACUUM is a product of  
precise engineering. The motor bearings are permanently  
lubricated and should not be oiled. If you require additional  
information or have problems with your ORECK appliance, you  
may call ORECK customer service or write to:  
Telephone: 0845 603 0153  
Oreck UK  
P.O. Box 107  
Exeter  
EX2 8ZQ  
Attention: Oreck Customer Service  
Please specify the model number and serial/code number which  
can be found on the data plate on the bottom of the vacuum.  
Save your sales or purchase slip. Should your ORECK  
appliance require warranty service in the U.S.A., present this slip  
to the Authorized Service Center as your proof of purchase date,  
or, in Canada, call customer service.  
Troubleshooting Guide  
PROBLEM  
POSSIBLE SOURCE  
AREAS TO CHECK  
Cleaner Will  
Not Run  
1.Not plugged in  
properly  
1.Be sure cleaner is  
firmly plugged into  
wall outlet.  
2.No electricity in  
wall outlet.  
2.Check electrical  
source–fuse or  
circuit breaker.  
3.Motor protector  
tripped.  
3.See Motor  
Protection System  
page 2.  
4.Needs service.  
4.Take to service  
center or call for  
nearest service  
center.  
Vacuum Will  
Not Pick Up  
Or Has Low  
Suction  
1.Filter bag is full.  
1.Replace filter bag.  
See “Changing  
the Filter Bag,”  
page 4.  
2.Hose/wand tool  
is clogged.  
2.Remove  
obstructions.  
3.Air leak due to  
missing or  
damaged gasket.  
3.Replace gasket  
See page 4.  
1.Proper friction fit  
not being  
obtained.  
Tools/Wands  
Will Not Stay  
Together  
1.Push and turn.  
ALL OTHER SERVICING SHOULD BE DONE BY AN  
ORECK AUTHORIZED SERVICE CENTER.  
CALL CUSTOMER SERVICE HOT LINE  
0845 603 0153  
Whenever calling, please be sure to have your model and serial  
number from data plate.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
73063-01 REV B 06/05 ECN# R-8022  
©2005 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used under the  
authority of Oreck Holdings, LLC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

MVOX electronic Conference Phone miniVox MV100 User Manual
Nikon Camcorder CT3A0311 6MN15911 03 User Manual
Nokia Cell Phone PM 3205 User Manual
NordicTrack Home Gym NTEL12910 User Manual
Nortel Networks Telephone LDP7004 User Manual
Oki Printer ML591 User Manual
Panasonic Camcorder AJ HD1800E User Manual
Panasonic Impact Driver EY7540 U1 User Manual
Panasonic VCR AJ HD130DCP User Manual
ParaBody Home Gym Leg Press 5 User Manual