Optimus VCR 114 16 551 User Manual

16-551.fm Page 1 Tuesday, July 20, 1999 5:13 PM

Cat. No. 16-551/633

OWNER’S MANUAL

Please read before using this equipment.

4-HEAD VHS HQ VCR

Model 114 (16-551)

Model 63 (Hi-Fi) (16-633)

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 3 Tuesday, July 20, 1999 5:13 PM

Lightning

Safety Check

— Upon completion of any service or

14.

15.

— For added protection for this VCR receiver

21.

22.

during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This

will prevent damage to the VCR due to lightning and

power-line surges.

repairs to this VCR, ask the service technician to perform

routine safety checks to determine that the VCR is in

proper operating condition.

Heat

— This VCR product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

Power Lines

— An outside antenna system should not

be located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep

from touching such power lines or circuits as contact with

them might be fatal.

Overloading

16.

17.

— Do not overload wall outlets and exten-

sion cords as this can result in a risk of fire or electric

shock.

Note to the cable TV system installer:

This reminder is to call the CATV system installer’s

attention to Section 820-40 of the National Electrical

Code, which provides guidelines for proper ground-

ing and, in particular, specifies that the cable ground

shall be connected to the grounding system of the

building, as close to the point of cable entry as prac-

tical.

Object and Liquid Entry

— Never push objects of any

kind into this VCR through openings as they may touch

dangerous voltage points or short out parts that could

result in a fire or electric shock. Never spill liquid of any

kind on the VCR.

Servicing

18.

19.

— Do not attempt to service this VCR yourself

as opening or removing covers may expose you to dan-

gerous voltage or other hazards. Refer all servicing to

qualified service personnel.

Damage Requiring Service

— Unplug this VCR from

Warning: To reduce the risk of fire

or shock hazard, do not expose

this product to rain or moisture.

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

•

When the power-supply cord or plug is damaged or

frayed.

CAUTION

•

If liquid has been spilled or objects have fallen into the

VCR.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

•

If the VCR has been exposed to rain or water.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVIC-

ING TO QUALIFIED PERSONNEL.

If the VCR does not operate normally by following the

operating instructions. Adjust only those controls that

are covered by the operating instructions, as improper

adjustment of other controls may result in damage

and will often require extensive work by a qualified

technician to restore the VCR to its normal operation.

•

If the VCR has been dropped or the cabinet has been

damaged.

This symbol is intended to alert you to the pres-

ence of uninsulated dangerous voltage within

the product’s enclosure that might be of suffi-

cient magnitude to constitute a risk of electric

shock. Do not open the product’s case.

When the VCR exhibits a distinct change in perfor-

mance — this indicates a need for service.

Replacement Parts

20.

— When replacement parts are

required, be sure the service technician has used

replacement parts, specified by the manufacturer, that

have the same characteristics as the original part. Unau-

thorized substitutions may result in fire, electric shock,

injury to persons or other hazards.

This symbol is intended to inform you that im-

portant operating and maintenance instructions

are included in the literature accompanying this

product.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 4 Tuesday, July 20, 1999 5:13 PM

FEATURES

Your Optimus Model 114/63 4-Head VHS HQ

VCR offers some of the most advanced fea-

tures available in home video cassette record-

ers.

Auto Repeat Playback — automatically re-

winds the tape for repeat playback when the

tape reaches the end during playback and re-

cording.

Your VCR’s VCR Plus+ feature lets you easi-

ly set the VCR to record programs without te-

dious programming, and its Commercial Ad-

vance and Movie Advance features let you

quickly skip over commercials and previews re-

corded on tapes. The VCR’s full-function uni-

versal remote control and on-screen pro-

gramming make the VCR easy to use.

Easy-to-Use Immediate Recording — lets

you start a recording immediately and have the

VCR automatically stop recording after a length

of time you select.

VCR Plus+ Timer Recording — lets you set

the VCR to automatically record programs by

using the PlusCode numbers published in

most television program schedules. Your VCR

automatically selects the channel you want to

record, so you don’t have to manually select it.

Your VCR offers all these features:

Note: The Model 63 includes all of the Model

114’s features, but adds Hi-Fi stereo that deliv-

ers CD-quality sound for audio/video or audio-

only recordings.

1-Month, 8-Event Digital Timer — lets you

program the VCR to make up to eight unat-

tended recordings (daily, weekly, or one-time).

Automatic Playback/Rewind/Eject — auto-

matically plays, rewinds, then ejects a tape.

RECORDING/PLAYBACK

Fast-Response System — positions the tape

next to the playback/record head for immediate

playback or recording.

26-Micron Record/Play Head — enhances

the picture quality at the EP (Extended Play)

playback speed.

Real-Time Counter with Memory — displays

the actual length of time a tape plays or

records, and allows you to mark and return to a

location on the tape.

Four Double-Azimuth Video Heads — pro-

vide superior picture quality and special effects

compared with standard single-azimuth four-

head VCRs.

AI (Artificial Intelligence) Video Noise Re-

duction System — reduces noise on the

screen when playing back a worn or partially

damaged tape.

TUNING

179-Channel, Digital-PLL, Cable-Compatible

Tuner — lets you tune to up to 68 VHF and

UHF channels, and up to 125 cable channels.

Commercial Advance — automatically de-

tects and skips over most commercials when

you play back a tape.

Tuner Memory Programming — automatical-

ly stores all the active channels in your area

into memory.

Movie Advance — lets you go directly to the

start of a movie or select which preview to view

on a purchased or rented tape.

Auto Tracking System — automatically ad-

justs tracking when you start playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 5 Tuesday, July 20, 1999 5:13 PM

Note: EDS is provided by some broadcasters

and includes various types of information, in-

cluding the current time. If no broadcasters in

your area transmit EDS signals, you must man-

ually set the clock.

TAPE CONTROL

Index Search — lets you quickly locate the

beginning of a specific recording. Also, you can

have the VCR play the first 10 seconds of each

recording so you can locate the one you want.

Automatic DST (Daylight Saving Time) Ad-

justment — lets you set the VCR to automati-

cally adjust the displayed time for Daylight

Saving Time.

Fast-Forward/Rewind with Visual Search

Freeze-Frame/Frame Advance/Slow-Motion

Automatic Rewind

We recommend you record the VCR’s model

and serial numbers here. This information is on

the VCR’s back panel.

OTHER FEATURES

Model: _______________________________

Multichannel Television Sound (MTS) (Mod-

el 63 only) — decodes stereo broadcasts for

listening or recording. This VCR can also re-

ceive and record special audio programs (SAP)

that accompany some MTS broadcasts.

Serial Number: ________________________

Front and Rear Audio/Video Input Jacks —

let you quickly connect an audio/video device,

such as a camcorder, to the VCR without dis-

connecting other devices.

Trilingual On-Screen Programming — pro-

vides helpful instructions on the TV screen for

setting the clock and timers. You can select

English, French, or Spanish instructions.

Universal Remote Control — lets you control

your VCR, as well as TVs and cable boxes pro-

duced by other manufacturers.

Memory Sentinel — protects clock settings,

tuner programming information, and timer

memory settings in case of a power loss. The

clock continues to run for 30 minutes, and tun-

er programming information and timer memory

settings are kept for up to 24 hours.

Automatic/Manual Clock Setting — lets you

set the VCR to automatically update its clock

using EDS (Extended Data Service) signals

sent by some TV stations. You can also manu-

ally set the clock.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 6 Tuesday, July 20, 1999 5:13 PM

CONTENTS

Before You Begin ......................................................................................................................... 8

Supplied Accessories .............................................................................................................. 8

Moisture Condensation ............................................................................................................ 8

Using This Manual ................................................................................................................... 8

Installation .................................................................................................................................... 9

Common Connections ............................................................................................................. 9

Model 63 Connections ........................................................................................................... 10

Model 114 Connections ......................................................................................................... 11

Home Theater Connections (Model 63 Shown) .................................................................... 12

Camcorder Connections ........................................................................................................ 13

Connecting Power ................................................................................................................. 13

VCR Setup .................................................................................................................................. 14

Setting the VCR’s Output Channel Switch ............................................................................ 14

Remote Control ..................................................................................................................... 14

Installing Batteries ........................................................................................................... 14

Using the Remote Control ............................................................................................... 14

Initial Set Up .......................................................................................................................... 15

Setting the On-Screen Language/Connection Type/Channels/Clock ............................. 15

Manually Setting the Clock ............................................................................................. 16

Adding/Erasing Channels ............................................................................................... 17

Reprogramming Tuner Memory ...................................................................................... 18

Turning On Auto Clock Set ............................................................................................. 19

Setting the Cable Box ..................................................................................................... 19

Changing the On-Screen Language ............................................................................... 20

Resetting the VCR’s Memory .......................................................................................... 20

Using the VCR’s Remote Control with Your TV or Cable Box ............................................... 21

Operation .................................................................................................................................... 23

Watching TV .......................................................................................................................... 23

Using the TV’s Tuner ...................................................................................................... 23

Using the VCR’s Tuner ................................................................................................... 23

Viewing a Video Tape ............................................................................................................ 23

Loading a Video Tape ..................................................................................................... 23

Playing a Video Tape ...................................................................................................... 24

Tape Motion Controls ............................................................................................................. 24

Fast-Forward/Rewind and Visual Search ........................................................................ 24

Freeze-Frame/Frame Advance ....................................................................................... 25

Slow Motion .................................................................................................................... 25

Real-Time Counter ................................................................................................................ 25

Using the Counter ........................................................................................................... 25

Using the Zero Search Function ..................................................................................... 25

Tracking ................................................................................................................................. 26

Special Functions ...................................................................................................................... 27

Special Displays .................................................................................................................... 27

Blue Screen Display ........................................................................................................ 27

On-Screen Display .......................................................................................................... 27

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 7 Tuesday, July 20, 1999 5:13 PM

Function Indicators ......................................................................................................... 27

Skipping Commercials .......................................................................................................... 27

Recording a Broadcast with Commercial Advance Marking ........................................... 27

Marking an Unmarked Tape ........................................................................................... 28

Playing Back with Commercial Advance Marking .......................................................... 29

Questions and Answers about Commercial Advance .................................................... 29

Skipping/Selecting Previews ................................................................................................. 29

Using Index Search ............................................................................................................... 30

Direct Access Index Search ........................................................................................... 30

Index Scan ...................................................................................................................... 31

Repeat Play .......................................................................................................................... 31

Recording ................................................................................................................................... 32

Recording Speeds/Tape Selection ........................................................................................ 32

Erase Protection ................................................................................................................... 32

Selecting the Signal to Record .............................................................................................. 33

Receiving/Recording Stereo/SAP Broadcasts (Model 63 Only) ............................................ 33

Immediate Recording ............................................................................................................ 33

Recording a Program as You Watch It ........................................................................... 33

Recording One Program on the VCR While You Watch Another on the TV ................... 34

Recording with VCR Plus+ .................................................................................................... 34

Setting the VCR Plus+ Guide Channels ......................................................................... 34

Timer Recording with VCR Plus+ ................................................................................... 35

Checking/Changing VCR Plus+ Programs ..................................................................... 37

Automatic Timer Recording ................................................................................................... 37

Setting a Timer ............................................................................................................... 38

Monitoring an Automatic Timer Recording ..................................................................... 40

Checking/Changing Timers ............................................................................................ 40

Clearing a Timer ............................................................................................................. 40

Dubbing ................................................................................................................................. 41

Audio-Only Recording (Model 63 Only) ................................................................................ 41

Additional Information .............................................................................................................. 42

Troubleshooting .................................................................................................................... 42

Care and Maintenance .......................................................................................................... 44

Servicing Your VCR ........................................................................................................ 45

Cleaning the Video Heads .............................................................................................. 45

Storing Your Video Cassettes ......................................................................................... 45

Specifications ........................................................................................................................ 46

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 8 Tuesday, July 20, 1999 5:13 PM

BEFORE YOU BEGIN

Recording — describes the different recording

methods.

SUPPLIED ACCESSORIES

Be sure to remove the remote control and 75-

ohm coaxial cable before you store the packing

material.

Additional Information — includes a trouble-

shooting section, care and maintenance proce-

dures, and the VCR’s specifications.

Depending upon your audio/video system set-

up, you might need additional cables or adapt-

ers (available at your local RadioShack store).

Read “Installation” on Page 9 to determine

your specific needs.

We recommend you thoroughly read at least

“Installation” on Page 9 and “VCR Setup” on

Page 14, to be sure you correctly install and

set up your VCR.

When reading through this manual, keep the

following in mind:

MOISTURE CONDENSATION

• Some buttons on the remote control also

appear on the VCR. You can use these

buttons to operate the same functions.

Other procedures use only the VCR’s but-

tons, or only the remote control’s.

Condensation inside the VCR can cause tape

jams or video head damage. When you move

the VCR from a cold area to a warmer one, let

it sit for about 2 hours before you plug it in and

begin operation. This allows any moisture in-

side the VCR to completely evaporate.

• Some buttons are labeled differently on the

VCR and on the remote control. Since you

use the remote control most often to

change settings and functions, this manual

refers only to the remote control’s labels.

Unless otherwise noted, however, you can

use either the remote control’s or the

VCR’s buttons at any time.

USING THIS MANUAL

This manual has these major sections:

Installation — shows you how to connect the

VCR to your audio/video system and a cam-

corder.

• All buttons, switches, and jacks on the

VCR and all buttons on the remote control

VCR Setup — includes procedures for setting

the output channel switch, preparing and using

the remote control, setting the on-screen pro-

gramming language, setting the channels your

VCR can tune, and setting the clock.

are shown in

this manual.

BOLD UPPERCASE letters in

• Information that appears on the TV screen

is shown in this typeface: PLAY

• Information that appears on the VCR’s dis-

play is shown in this typeface: VCR

Operation — explains how to watch TV using

the TV’s or VCR’s tuner, load and play a video

tape, fast-forward and rewind a tape, use the

VCR’s special playback, display, and search

features, use the real-time counter and the

zero search function, and set the tracking man-

ually.

• The VCR displays menus and options on

the TV you connect it to, and other infor-

mation (such as tape motion indicators, the

real-time counter, etc.) on its display.

If a menu disappears before you finish

entering information, simply locate the step

where you first pressed MENU on the

remote control, then repeat that step and

all steps that follow.

Special Functions — describes what appears

on the VCR’s display and the TV screen, how

to use the VCR’s Commercial Advance and

Movie Advance features, use index search,

and use repeat play.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 9 Tuesday, July 20, 1999 5:13 PM

INSTALLATION

Caution: Some state laws restrict

direct connections to cable wires

(connections that do not go through a

cable box). Check the laws in your

area before you make connections.

COMMON CONNECTIONS

Refer to the illustrations on Page 10 (Model 63)

or 11 (Model 114) for these connections.

Note: Some connections shown in this section

might require additional supplies, available

from your local RadioShack store.

• A cable converter box to the VCR’s IN

FROM ANT. jack

Note: There are many cable TV sys-

tems in use. If you subscribe to cable

TV service and cannot record cable TV

programs, contact your local cable TV

service provider. Most cable TV service

providers offer connection help.

Connect the VCR to your TV for play-

back. You can connect (choose one):

• Your VCR’s VHF/UHF OUT TO TV jack

to your TV’s antenna jack, using a

75-ohm coaxial cable

Caution: Never connect the VCR’s

VHF/UHF OUT TO TV jack to a termi-

nal that has an antenna already con-

nected. Doing so can interfere with

other receivers.

You can also connect an optional

video source, such as a camcorder,

another VCR, or a DSS system to

your VCR using A/V cables. Simply

connect it as shown.

• Your VCR’s VHF/UHF OUT TO TV jack

to your TV’s separate VHF/UHF

antenna jacks, using a 75-ohm coax-

ial cable and a VHF/UHF splitter/

combiner

Connection Notes:

• You can connect three video sources

directly to your VCR. To do so, you connect

one source to the AUDIO IN 1/VIDEO IN 1

(Model 114) or R-AUDIO-L IN 1/VIDEO IN 1

(Model 63) jacks on the back of the VCR

using A/V cables, another source to the IN

FROM ANT. jack using a 75-ohm coaxial

cable, and another source to the AV2 VIDEO

IN/AUDIO IN (Model 114) or AV2 VIDEO IN/L-

AUDIO IN-R (Model 63) jacks on the front of

the VCR (see “Camcorder Connections” on

Page 13).

• Your VCR’s R-AUDIO-L/VIDEO OUT

jacks to your TV’s audio/video jacks,

using a stereo audio/video cable

Note: For the best quality recordings,

use high-quality A/V cables to make

these connections.

Connect a signal source to the VCR

for recording. You can connect

• You can connect additional 75-ohm

coaxial sources to your system using a

high-isolation A/B switch to switch

between the sources.

(choose one):

• An outside antenna, using a 75-ohm

coaxial cable, to the VCR’s IN FROM

ANT. jack

• You can connect one 75-ohm coaxial

source to more than one device using a

video splitter.

• An outside antenna, using 300-ohm

lead-in wire and a 300-to-75 ohm

transformer, to the VCR’s IN FROM

ANT. jack

Because of the complexity of the variations

possible when using additional video accesso-

ries, such as video signal switches, splitters,

and combiners, such configurations are not

shown in this manual.

• Your CATV (cable) source, using the

75-ohm coaxial cable directly from

the cable company, to the VCR’s IN

FROM ANT. jack

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 10 Tuesday, July 20, 1999 5:13 PM

MODEL 63 CONNECTIONS

Outside

Antenna

300-Ohm

Lead-In Wire

75-Ohm

Coax Cable

Cable

(CATV)

Cable Box

Company

75-Ohm

Coax Cable

300-to-75 Ohm

Transformer

I N

OUT

(Optional Camcorder/2nd VCR/DSS System)

Stereo

Audio/Video

Audio

Video

Cable

Model 63 (rear)

R-AUDIO-L

VIDEO

IN FROM

ANT.

VHF/UHF

OUT

MONO

OUT TO TV

CH. 4

IN 1

Stereo

Audio/Video

Cable

75-Ohm

Coax Cable

Optional TV

Antenna In

Connection

VHF/UHF

Splitter/Combiner

UHF

VHF

Video In

Audio In

Antenna In

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 11 Tuesday, July 20, 1999 5:13 PM

MODEL 114 CONNECTIONS

Outside

Antenna

300-Ohm

Lead-In Wire

75-Ohm

Coax Cable

Cable

(CATV)

Cable Box

Company

75-Ohm

Coax Cable

300-to-75 Ohm

Transformer

I N

OUT

(Optional Camcorder/2nd VCR/DSS System)

Audio/Video Cable

Audio

Video

Model 114 (rear)

AUDIO

VIDEO IN FROM

ANT.

OUT

IN 1

VHF/UHF

OUT TO TV

CH. 4

75-Ohm

Coax Cable

Audio/Video

Cable

Optional TV

Antenna In

Connection

VHF/UHF

Splitter/Combiner

UHF

VHF

Video In

Audio In

Antenna In

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 12 Tuesday, July 20, 1999 5:13 PM

HOME THEATER CONNECTIONS (MODEL 63 SHOWN)

Refer to this illustration to connect your VCR to a home theater system.

Outside

Antenna

300-Ohm

Lead-In Wire

75-Ohm

Coax Cable

Cable

(CATV)

Company

Cable Box

75-Ohm

Coax Cable

300-to-75 Ohm

Transformer

I N

OUT

Select the signal

source you have

Stereo Audio/Video Cable

Model 63

(rear)

A/V RECEIVER

Speakers

Front

Left

Right

–

Center

R-AUDIO-L

VIDEO

R-AUDIO-L

VIDEO

IN FROM

ANT.

VHF/UHF

–

OUT

TV/Monitor

Rear

MONO

Left

Right

OUT TO TV

CH. 4

–

IN 1

Stereo

Audio/Video

Cable

75-Ohm

Coax Cable

Video Cable

Speakers

Video In

Audio In

Antenna In

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 13 Tuesday, July 20, 1999 5:13 PM

CAMCORDER CONNECTIONS

Your VCR has jacks on its front panel that let you easily connect a camcorder or other video

AUDIO IN 1/VIDEO IN 1

R-AUDIO-L

(Model 114) or

source. You can also connect a camcorder to the

IN 1/VIDEO IN 1

(Model 63) jacks on the back of the VCR.

The Model 63 needs a stereo audio/video cable for this connection. The Model 114 needs an au-

dio/video cable for this connection. Your audio/video cable (not supplied) must have plugs that fit

the VCR’s jacks and the camcorder’s jacks for this connection.

PLAY

REWIND

FAST-F

VIDEO IN

–

AUDIO IN

–

RECORD/TIME

STOP

EJECT

POWER

TV/VCR

AV 2 L-AUDIO IN-R

AV VIDEO IN

jacks on

1. Insert the plugs at one end of the cable into the

and

AUDIO IN/VIDEO IN

the Model 63’s front panel, or the

jacks on the Model 114’s front panel.

2. Insert the plugs at the other end of the cable into the AUDIO/VIDEO OUT jacks on your cam-

corder or other video source. Be sure to connect VIDEO to VIDEO and AUDIO to AUDIO (use

the plug’s color codes as a guide).

CONNECTING POWER

To power the VCR, plug its power cord into a standard AC outlet. --:-- appears on the display.

Note: The VCR prompts you to select a language, connection type, and output channel, then

starts to search for a channel that has an Extended Data Service (EDS) signal (see “Initial Setup”

on Page 15) when:

POWER

• You plug in the VCR for the first time then press

to turn it on.

• You unplug the VCR and reconnect it (within 24 hours) or after a power failure (of less than 24

POWER

hours) then press

to turn it on.

• You reset the VCR’s memory (see “Resetting the VCR’s Memory” on Page 20).

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 14 Tuesday, July 20, 1999 5:13 PM

VCR SETUP

2. Put fresh batteries in the compartment, as

indicated by the polarity symbols (+ and –)

marked inside.

SETTING THE VCR’S OUTPUT

CHANNEL SWITCH

If you connected the VCR’s VHF/UHF OUT TO

TV terminal to a TV or another VCR, set 3 CH. 4

on the back of the VCR to 3 or 4, whichever is

not an active channel in your area.

When VCR appears, the VCR sends the signal

from the video source connected to its IN FROM

ANT. jack or R-AUDIO-L IN 1/VIDEO IN 1 (or AV2

for the Model 63) terminals to the TV on the

channel you selected.

3. Replace the cover.

3 CH. 4 has no effect on the TV

Note: Setting

when the VCR is off or if you connected a TV

with separate audio/video input jacks to the

VCR’s R-AUDIO-L/VIDEO IN jacks.

Note: When the remote control stops working

or operates poorly, replace both batteries.

REMOTE CONTROL

Cautions:

• Never leave dead or weak batteries in the

remote control. Batteries can leak chemi-

cals that can damage your remote control.

Installing Batteries

The remote control requires two AA batteries

(not supplied). For the longest operation and

best performance, we recommend alkaline bat-

teries (such as RadioShack Cat. No. 23-557).

• Dispose of dead batteries promptly and

properly; do not bury or burn them.

Using the Remote Control

Cautions:

• Use only fresh batteries of the required

size and recommended type.

To use the remote control, aim it at the front of

the VCR and press the desired function but-

tons.

• Do not mix old and new batteries, different

types of batteries (standard, alkaline, or

rechargeable), or rechargeable batteries of

different capacities.

1. Press the tab on the battery compartment

cover and lift off the cover in the direction

of the arrow.

Tab

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 15 Tuesday, July 20, 1999 5:13 PM

INITIAL SET UP

Setting the On-Screen Language/

Connection Type/Channels/Clock

When you first plug in the VCR and turn it on,

when you turn it on after power was interrupted

for longer than 24 hours, or when you reset the

VCR’s memory, the VCR prompts you to select

a language, then scans for active channels in

your area and stores them.

4. When the following appears on the TV

PLAY

screen, repeatedly press

(with s

(with t marked

below it) on the remote control to highlight

STOP

marked above it) or

a connection type, then press

marked to its right) to select it.

(with

In many areas, the Public Broadcasting Ser-

vice (PBS) station broadcasts an electronic

data signal (EDS) with its regular broadcast.

This signal can automatically set your VCR’s

clock to the correct time. If a station in your

area has EDS signals, the VCR automatically

sets the clock.

S B

Notes:

• If you connected a cable box or a DSS

receiver to the VCR then connected the

VCR to a TV, select CABLE/DSS

BOX VCR TV.

• The VCR is preset to automatically set the

clock, but you can change this setting. See

“Manually Setting the Clock” on Page 16.

• If no stations in your area broadcast EDS

signals, you can set the clock manually.

See “Manually Setting the Clock” on

Page 16 for more information.

• If you connected the VCR to a cable box

or a DSS receiver then connected the

cable box/DSS receiver to a TV, select

VCR CABLE/DSSBOX TV.

• If you connected the VCR directly to a

POWER

1. Press

to turn on the VCR.

TV, select VCR TV.

2. Turn on your TV and set it to the same

If you selected CABLE/DSS BOX VCR

TV, continue with Step 5. If you selected

VCR CABLE/DSS TVor VCR TV, skip

to Step 6.

3 CH. 4

channel as the VCR’s

select its line input if you connected the

VCR to the TV’s audio/video input jacks.

switch or

TV/VCR

Then press

so VCR appears.

5. When the following appears on the TV

3. Select a language by pressing

s (to

t (to select Spanish), or

(to select French) when the follow-

ing appears on the TV screen.

screen, repeatedly press

your cable box’s or DSS receiver’s output

s or t to select

select English),

TV/VCR

channel number, then press

OUTP

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 16 Tuesday, July 20, 1999 5:13 PM

Notes:

to the correct time and AUTOCLOCKSET

COMPLETEDappears. If the VCR does not

detect a signal within this time, AUTO

CLOCK SET INCOMPLETE appears.

There is probably not an EDS signal avail-

• The output channel number for most

cable boxes and DSS receivers is usu-

ally 3 or 4. Check the owner’s manual

for your cable box or DSS receiver if you

are not sure what the output channel

number is.

STOP

, then see

able in your area. Press

“Manually Setting the Clock” to set the

clock.

• If you are using the audio/video jack

connections to your cable box or DSS

receiver, select VIDEOOUTas the out-

put channel.

Notes:

• Your VCR protects tuner programming for

up to 24 hours in case a power failure

occurs or if the power cord becomes

unplugged. After about 24 hours without

power, the VCR loses the programming.

6. When the following appears on the TV

screen, set your cable box or DSS receiver

to the local PBS station, then press

(If you do not have a cable box or DSS

• If you have not connected the VCR to an

antenna, cable box, DSS receiver, or

receiver, simply press

s.)

IN FROM

other signal source through the

ANT.

jack, the VCR does not store any

AUT

SET

channel in memory. Instead, you see:

A CABLE

THE

. . .

NO CH FOUND

KEY

PLEASE CHECK ANTENNA

CABLE CONNECTION THEN

PUSH VCR CH UP KEY AGAIN

After you press

s, CHAUTOSET PRO-

CEEDINGand the current channel number

appear on the TV screen as the VCR scans

through the channels and memorizes all

active channels in your area.

Manually Setting the Clock

Note: If you have already set the channels

and just want to manually set the clock,

Follow these steps to set the VCR to not

search for an EDS signal then to manually set

the clock.

press

to skip tuner programming.

Then see “Manually Setting the Clock.”

7. When the VCR finishes scanning and stor-

ing channels, it searches for an EDS signal

and shows the following on the TV screen:

Notes:

• The clock must be accurately set for proper

automatic timer recording. We suggest you

refer to a radio station or time/temperature

service for the correct time.

AUTO CLOCK SET

PROCEEDING

• If you do not press a button within 5 min-

utes in Steps 2–9, the clock is not set. Start

again from Step 1.

CANCEL: PUSH STOP KEY

It takes up to 10 minutes for the VCR to set

the clock using the EDS signal. If the VCR

finds a signal, it automatically sets its clock

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 17 Tuesday, July 20, 1999 5:13 PM

1. Press MENU to display the main menu.

00PM

To exit the programming mode at

Note:

DST:

any time, press MENU.

2. Repeatedly press PLAY or STOP to high-

light SETCLOCK, then press FF.

3. Repeatedly press PLAY or STOP to high-

If the information is not correct, move the

cursor to the incorrect entry by repeatedly

light MANUALSET, then press FF.

pressing REW (with

marked to its left) or

FF, then enter the correct information.

When the information is correct and the

time reaches the minute you set in Step 6,

press MENU twice. The time you set

appears and the clock starts running.

4. Repeatedly press PLAY or STOP to select

Seconds begin counting from 00

when you press MENU twice.

Note:

the correct month, then press FF.

DST:

Adding/Erasing Channels

We recommend you check the channels the

VCR automatically stored. It might have stored

distant, weak channels that you normally would

not watch, or it might have missed channels

you want to store.

5. Repeat Step 4 to select the correct date,

year, and hour, then press FF.

Your VCR uses a 12-hour clock. Be

sure you correctly set AM or PM.

Note:

If the tuner stores a channel that you do not

want, repeatedly press (or hold down) CH s or t

to tune to that channel, then press ADD/DLT.

6. Repeatedly press PLAY or STOP to select a

minute that is 1 or 2 minutes after the current CHANNELnnDELETEDappears, and the un-

time, then press FF. (For example, if it is 42

minutes past the hour right now, enter 43

minutes.) This gives you time to complete

this procedure before starting the clock.

wanted channel is erased from the tuner’s

memory.

If you want to add a channel, enter the desired

channel number using the remote control’s

number buttons. Then press ADD/DLT. CHAN-

NEL nn ADDED appears, and the channel is

added to memory.

7. Repeatedly press PLAY or STOP to set DST

(daylight saving time) to ONor OFF.

When you set DST to ON, the VCR auto-

matically adds 1 hour on the first Sunday in

April, and subtracts 1 hour on the last Sun-

day in October.

CHANNEL 08 ADDED

CHANNEL 08 DE

TED

8. Press FF. SETCOMPLETEDappears.

9. Review the information you entered.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 18 Tuesday, July 20, 1999 5:13 PM

do not have a cable box or DSS receiver,

simply press CH s.)

Reprogramming Tuner Memory

You might want to reprogram the VCR’s tuner

memory if you move or change from an anten-

na connection to a cable TV connection.

After you press CHs, CHAUTOSET PRO-

CEEDINGand the current channel number

appear on the TV screen as the VCR scans

through the channels and memorizes all

active channels in your area.

Note: You can also quickly erase all settings,

including the time, local channels, and pro-

grammed events, then reprogram the tuner’s

memory. See “Resetting the VCR’s Memory”

on Page 20.

6. When the VCR finishes scanning and stor-

ing channels, it searches for an EDS signal

and shows the following on the TV screen:

Follow these steps to reprogram the tuner.

1. Press MENU to display the main menu.

AUTO CLOCK SET

PROCEEDING

Note: To exit the programming mode dur-

ing Steps 2–5, press MENU again.

CANCEL: PUSH STOP KEY

2. Repeatedly press PLAY or STOP to high-

light SETUPCHANNEL, then press FF.

It takes up to 10 minutes for the VCR to set

the clock using the EDS signal. If the VCR

finds a signal, it automatically sets its clock

to the correct time, and AUTO CLOCK

SET COMPLETED appears. If the VCR

does not detect a signal within this time,

AUTO CLOCK SET INCOMPLETE

appears. There is probably not an EDS sig-

nal available in your area. Press MENU,

then see “Manually Setting the Clock” on

Page 16 to set the clock.

E: ENGL I S

3. Press FF again to select the broadcast sys-

tem (TVor CATV).

NNEL

Notes:

CATV

SET UP

• Your VCR protects tuner programming for

up to 24 hours in case a power failure

occurs or if the power cord becomes

unplugged. After about 24 hours without

power, the VCR loses the programming.

4. Press PLAY or STOP to highlight AUTO SET,

then press FF. You see:

AUT

SET

A CABLE

YOU

THE

. . .

KEY

5. Set your cable box or DSS receiver to the

local PBS station, then press CH s. (If you

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 19 Tuesday, July 20, 1999 5:13 PM

• If you have not connected the VCR to an

antenna, cable box, DSS receiver, or

other signal source through the IN FROM

ANT. jack, the VCR does not store any

channel in memory. Instead, you see:

Setting the Cable Box

When you change the connections to your

VCR (for example, when you subscribe to a ca-

ble company’s service), follow these steps to

change the antenna system settings.

NO CH FOUND

1. Press MENU to display the main menu.

PLEASE CHECK ANTENNA

CABLE CONNECTION THEN

PUSH VCR CH UP KEY AGAIN

2. Repeatedly press PLAY or STOP to high-

light SET UP CHANNEL, then press FF.

You see:

NNEL

CATV

SET UP

ET UP

Turning On Auto Clock Set

If you turned off the auto clock set feature and

manually set the VCR’s clock, then find that

EDS is available in your area, you can turn the

auto clock set feature back on. This ensures

that the VCR sets itself to the correct time after

a power failure of less than 24 hours.

3. Be sure CATVappears next to ANTENNA

SYSTEM. If not, repeatedly press PLAY or

STOP to select ANTENNA SYSTEM, then

press FF to select CATV.

Follow these steps to turn on auto clock set.

Then repeatedly press PLAY or STOP to

highlight CABLE/DSS BOX SET UPand

press FF. You see:

1. Press MENU to display the main menu.

2. Repeatedly press PLAY or STOP to high-

light SETCLOCK, then press FF. You see:

4. If necessary, repeatedly press PLAY or

STOP on the remote control to highlight

VCR CABLE/DSSBOX TV. Then press

FF. You see:

3. If necessary, press PLAY or STOP to high-

light AUTOSET, then press FF.

4. Press CH s. The VCR searches for an EDS

signal and, if it finds one, automatically

sets its clock to the correct time. If the VCR

does not find an EDS signal, follow the

steps under “Manually Setting the Clock”

on Page 16.

NNEL

CATV

SET UP

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 20 Tuesday, July 20, 1999 5:13 PM

The display prompts you to select the

cable box’s output channel number.

Repeatedly press CH s or t to select the

number, then press FF.

OSCO

: FRANÇAI S

Français

OUTP

3. Repeatedly press FF so the desired lan-

guage appears next to the fourth item.

4. When you finish, press MENU.

5. When you finish, press MENU twice.

Resetting the VCR’s Memory

Changing the On-Screen Language

You can erase all settings (including the time,

local channels, and programmed events) at

any time. Eject any loaded tape, then hold

down PLAY and CHANNEL s on the VCR for

about 5 seconds until it turns itself off. All set-

tings are cleared.

Follow these steps to change the on-screen

programming language.

1. Press MENU to display the main menu.

2. Repeatedly press PLAY or STOP to high-

light the fourth menu selection, then press

FF. (The title of the fourth menu selection

differs depending on the language cur-

rently selected).

The next time you turn on the VCR, it performs

its initial setup sequence. See “Setting the On-

Screen Language/Connection Type/Channels/

Clock” on Page 15.

E: ENGL I S

English

E: ESPANOL

Espanõl

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 21 Tuesday, July 20, 1999 5:13 PM

USING THE VCR’S REMOTE

CONTROL WITH YOUR TV OR

CABLE BOX

BRAND

CODE

Archer

01, 29, 44, 88, 91

Cableview

04, 30, 42, 44, 52, 63,

85, 88

In addition to controlling your VCR, the remote

control can operate the basic functions of your

TV and cable box. Follow these steps to pro-

gram the remote control with the correct manu-

facturer’s code number for that TV and cable

box.

Citizen

04, 30, 42, 44, 52, 63,

85, 88

Curtis

08, 09, 56, 61, 87, 90

01, 29, 44, 88, 91

37, 67, 71

Diamond

Drake

Note: Some brands have more than one code

listed in the charts. If a code does not work with

your TV or cable box, try another. The listed

codes might not work with all models from the

listed manufacturers.

Eagle

13, 20, 22, 26, 40, 58,

62, 98

Eastern

GC Brand

04, 30, 42, 44, 52, 63,

85, 88

1. Find the code for your TV and cable box in

the following charts.

Gemini Regal

04, 85

General Electric

TV BRAND

Fisher

CODE

General Instru-

ment

01, 02, 03, 04, 34, 55,

83, 85, 91, 93, 95

Hamlin

14, 15, 28, 41, 97, 100,

102

Goldstar

Hitachi

15, 16, 17

Hitachi

Jerrold

31, 79

01, 02, 03, 04, 34, 55,

83, 85, 91, 93, 95

JVC

Macom

31, 79

Magnavox

Mitsubishi

Panasonic

Quasar

RadioShack

RCA

Magnavox

Matsushita

Movietime

25, 26

07, 13

16, 17, 101

01, 02

29, 32, 38, 39, 40, 42,

44, 88

01, 02

01, 02, 15, 16, 17

NSC

32, 38, 40

Oak

10, 11, 46, 99

44, 88

Realistic

Samsung

Sanyo

01, 02, 15, 16, 17

Optimus

Panasonic

Philips

Pioneer

Pulsar

16, 17, 101

13, 20, 23, 24, 96

05, 06, 78

Sharp

06, 07

Sony

04, 30, 42, 44, 52, 63,

85, 88

Sylvania

Toshiba

Zenith

RadioShack

RCA

44, 88

16, 17, 101

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 22 Tuesday, July 20, 1999 5:13 PM

Precede a single-digit code number with a

0 — for example, 01, 02, etc. To enter a

three-digit number, press 100, then enter

the second and third digits in the code

number.

CABLE BOX

CODE

BRAND

Realistic

44, 51, 88

Regal

14, 41

3. Try operating your TV or cable box using

the VCR’s remote control. First press TV or

CATV, then try pressing POWER, INPUT, CH

s or t, and VOL +/– for TV operation; or

POWER and CH s or t for cable box opera-

tion.

Regency

Rembrandt

Samsung

Scientific Atlanta

Sheritech

SL Marx

29, 32, 39, 42, 44, 88

32, 40, 42, 78, 94

08, 09, 56, 61, 87, 90

If the device does not function, repeat Step

2 and try other codes for the manufacturer.

If it still does not function, you must use the

original remote control supplied with your

TV or cable box.

32, 40, 42, 78, 94

16, 17, 101

Sprucer

Stargate

04, 30, 32, 40, 42, 44,

52, 63, 78, 85, 88, 94

Sylvania

Teknika

To use the VCR’s remote control, press the

button for the device you want to control — TV,

CATV, or VCR. Then press the desired function

button.

Telecaption

Teleview

Texscan

Tocom

77, 92

32, 40, 42, 78, 94

18, 19

Notes:

01, 33, 34, 42, 48, 49,

• The codes you programmed might be

erased if you remove the batteries from the

remote control (to replace them, for exam-

ple). If this happens, re-enter the codes

after you replace the batteries.

Toshiba

Uniden Satellite

Unika

65, 69

01, 29, 44, 88, 91

42, 43, 44, 52, 63, 88

• Some TVs and cable boxes might require

that you manually turn on the power for

that device.

Universal

Viewstar

13, 20, 22, 26, 40, 58,

62, 98

• Your TV or cable box might have functions

that the VCR’s remote control will not oper-

ate.

Videoway

Vid Tech

Vidter

07, 23, 50

• You can use the number buttons to select a

channel number on your TV and cable box.

However, some TVs/cable boxes might

require that you press DISP/ENT after

entering the channel number.

Zenith

07, 23, 50

2. While holding down TV, enter the code

number for your TV using the number but-

tons. Or, while holding down CATV, enter

the code number for your cable box using

the numbered buttons.

• VOL +/– works to adjust the TV volume in

any operation mode (VCR, TV, or CATV).

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 23 Tuesday, July 20, 1999 5:13 PM

OPERATION

jacks, set the TV/monitor to the video

mode.

WATCHING TV

Using the TV’s Tuner

2. Repeatedly press TV/VCR until VCR

appears.

To watch a broadcast using the TV’s tuner, turn

off the VCR, or repeatedly press TV/VCR until

VCR disappears.

3. To manually select a channel, you can

press CH s or t to have the tuner automati-

cally advance to the next channel stored in

the tuner’s memory.

Note: If you are using a TV/monitor connected

to the VCR’s R-AUDIO-L/VIDEO OUT jacks, be

sure to set the TV/monitor to the TV mode.

CH s when the tuner is

Note: If you press

at the highest programmed channel or CH t

when the tuner is at the lowest pro-

grammed channel, the VCR enters the

audio/video mode and LINE1 or LINE2

appears on the TV (see “Selecting the Sig-

nal to Record” on Page 33). Continue to

press CH s or t until the highest or lowest

programmed channel appears.

The antenna or cable signals pass through the

VCR unaffected, as if the antenna or cable

were connected directly to the TV. Use the TV

as you normally would.

Using the VCR’s Tuner

Or, to directly select a channel, press the

number buttons on the remote control for

the desired channel.

Your VCR can receive up to 68 VHF and UHF

channels, and up to 125 cable channels. The

VCR displays the channels as 1–125.

Notes:

• Precede a single-digit number with a 0

— for example, 01, 02, and so on.

• Channels 2–13 are the same for VHF and

cable TV, and cable companies usually

number them as they appear on the dis-

play.

• To enter a three-digit number, press 100,

then enter the second and third digits in

the channel number.

• Since cable companies sometimes desig-

nate cable channels with letters or letter-

number combinations, a channel number

you see on the VCR’s display might differ

from the channel number displayed on

your cable box. You might need to experi-

ment to determine the proper cable chan-

nel designations for your cable system. For

more information, contact your local cable

company.

• (Model 63 only) If you want to receive

MTS stereo or SAP broadcasts, see

“Receiving/Recording Stereo/SAP Broad-

casts (Model 63 Only)” on Page 33.

VIEWING A VIDEO TAPE

Loading a Video Tape

1. Turn on the TV and set it to the same chan-

• Two cable channels are designated for

audio only.

nel as the VCR’s 3 CH. 4 switch.

Note: If you are using a TV/monitor that is

connected to the VCR’s R-AUDIO-L/VIDEO

OUT jacks, set the TV/monitor to the video

mode.

1. Turn on the TV and set it to the same chan-

nel as the VCR’s 3 CH. 4 switch.

Note: If you are using a TV/monitor con-

nected to the VCR’s R-AUDIO-L/VIDEO OUT

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 24 Tuesday, July 20, 1999 5:13 PM

2. Hold the cassette with the main label fac-

ing up and the spine facing out from the

VCR. Then insert the cassette into the

VCR’s compartment and gently push the

center of its spine until the VCR draws it in.

Notes:

• If the tape reaches the end before you

STOP STOP EJECT

, the VCR auto-

press

matically stops the tape and completely

rewinds it. If the erase-protection tab has

been removed, the VCR then ejects the

cassette.

STOP

• When the VCR is off, you can press

EJECT

on the VCR to eject a tape. The

VCR turns on, ejects the tape, then turns

itself off.

The VCR automatically turns on. If the erase-

protection tab has been removed from the cas-

sette, playback automatically begins.

TAPE MOTION CONTROLS

Fast-Forward/Rewind and Visual

Caution: Never insert anything except a VHS

video cassette into the cassette compartment.

Anything else might damage the VCR.

While a tape is stopped, press

to advance

REW

the tape quickly or

to rewind it. You can-

not see the picture or hear sound when you

use fast-forward or rewind, but you can use the

counter to locate a specific section of tape.

Playing a Video Tape

1. Load a video tape.

POWER

while a tape is re-

2. If playback does not automatically begin,

Note: If you press

PLAY

. The VCR plays the tape.

press

winding, REWIND POWER OFF appears.

The VCR automatically turns itself off when re-

winding is complete.

Note: During playback, the VCR automati-

cally adjusts tracking, but you can manu-

ally adjust it if necessary (see “Tracking”

on Page 26).

To use visual search so you can see the pic-

ture, be sure VCR appears, then begin tape

FF REW

to search forward or

3. (Model 63 only) To choose the type of

audio you want to hear during playback,

playback. Press

PLAY

to search in reverse. Press

normal playback.

to return to

SAP/HiFi

press

until an arrow appears next

to the desired audio mode indicator (HiFi

or NORMAL) on the TV screen.

During visual search, the sound is muted and

the picture quality is lower than during normal

playback. The search picture is best with tapes

recorded at the SP or EP speed (see “Record-

ing Speeds/Tape Selection” on Page 32).

Note: If you play a tape recorded on a

standard VCR, the Model 63 plays the

standard audio track, regardless of the

audio output setting.

4. To stop playback before the end of the

STOP

tape, press

STOP EJECT

5. To eject the tape, press

the VCR.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 25 Tuesday, July 20, 1999 5:13 PM

Freeze-Frame/Frame Advance

REAL-TIME COUNTER

Freeze-frame lets you pause the tape to view a

single frame. Press PAUSE during playback to

freeze the picture. Press PAUSE again or PLAY

to return to normal playback.

Using the Counter

Your VCR’s counter shows how long a tape

has been running. To have the counter display

on the TV screen, press DISP/ENT on the re-

mote control.

During freeze-frame, picture quality is lower

than during normal playback. The picture quali-

ty is best with recordings made at the SP or EP

speed (see “Recording Speeds/Tape Selec-

tion” on Page 32).

The counter resets to 0:00:00 when you

eject a tape then put in a new tape. To reset it

manually, press COUNTER RESET.

Notes:

Note: The real-time counter might stop if you

fast-forward or rewind through a blank section

on the tape. This is normal.

• If you leave the VCR in the freeze-frame

mode for 3 minutes, the VCR stops playing

the tape to protect the video heads.

Using the Zero Search Function

• To reduce or eliminate jitter in the freeze-

frame picture, hold down CH s or t until the

picture is clear.

You can reset the counter to 0:00:00at any

position on the tape and then return to that po-

sition. This lets you quickly return to a selected

place on the tape later.

During freeze-frame, you can advance the pic-

ture one frame at a time by repeatedly pressing

SLOW. This feature works best with video cas-

settes recorded at the SP or EP speed. Press

PAUSE or PLAY to return to normal playback.

Follow these steps to use the zero search func-

tion.

1. Press COUNTER RESET twice at the loca-

tion you want to return to later. The counter

resets to 0:00:00.

Slow Motion

To start slow motion playback, while a tape is

playing, press SLOW. Press SLOW again or

PLAY to return to normal playback. During slow

motion, the sound is muted and the picture

quality is lower than during normal playback.

Slow motion picture quality is best with tapes

recorded at the SP or EP speed.

2. When you want to return to the selected

location, stop the tape, then press C/A

SKIP/ZERO. The tape rewinds or fast-

forwards and automatically stops when it

reaches 0:00:00.

Notes:

• If you press REW to rewind the tape past

0:00:00, the time appears with a minus

(–) sign.

Notes:

• If you leave the VCR in the slow-motion

mode for 3 minutes, the VCR stops playing

the tape to protect the video heads.

• The counter does not work with blank

tapes or blank portions of partially

recorded tapes.

• If the slow-motion picture is poor, hold

down CH s or t until the picture improves.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 26 Tuesday, July 20, 1999 5:13 PM

TRACKING

The auto tracking system automatically adjusts

tracking when you start playback.

When different parts of the tape are recorded

at different speeds, the VCR automatically re-

adjusts the tracking at the beginning of each

recording.

If you need to manually adjust tracking, hold

down

s or t. To return to the automatic

tracking system, press

s and t at the same

time or turn the power off then back on.

Notes:

• You might need to slightly readjust tracking

for each tape you play.

• If the sound of a recording made on

another VHS Hi-Fi VCR is poor, you might

be able to improve it by adjusting the track-

ing.

Hint for Model 63 only: If the tracking is incor-

rect and needs adjustment, Hi-Fi does not

appear.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 27 Tuesday, July 20, 1999 5:13 PM

SPECIAL FUNCTIONS

SPECIAL DISPLAYS

SKIPPING COMMERCIALS

Your VCR’s Commercial Advance

feature

Blue Screen Display

lets you quickly skip over commercials record-

ed onto a tape while you view it, without having

to continually press FF.

The VCR displays a blue screen on the TV

when you select the VCR mode, play unre-

corded portions of a tape, or when you tune to

a weak TV station. The blue screen also ap-

pears if you set the VCR to the audio/video

mode when the R-AUDIO-L/VIDEO IN jacks are

not receiving any signals.

During recording, Commercial Advance stores

in memory the locations of the beginnings and

endings of commercials. After recording is

over, the VCR replays the tape and marks the

beginnings/endings on the tape itself. Then,

when you play back the recording, you can set

the VCR so it automatically detects and skips

over the marked commercials or only skips

over the marked commercials when you press

a key.

Note: You cannot record the blue screen on a

tape in the VCR.

On-Screen Display

To view your VCR’s current operating mode

and other information about your VCR, press

DISP/ENT (display/enter). You see the current

function, time, channel, counter, and tape

speed. If you have a Model 63, you also see

the broadcast type (STEREO, SAP, or MONO).

Press DISP/ENT again to clear the display.

Notes:

• The effectiveness of Commercial Advance

varies with the different methods stations

use to broadcast commercials. It is possi-

ble that Commercial Advance might not

work with every broadcast you watch.

• Commercial Advance does not erase com-

mercials from the tape; it simply marks

them.

Note: You also see the remaining recording

time while a timed recording is in progress (see

“Immediate Recording” on Page 33).

Recording a Broadcast with

Commercial Advance Marking

Function Indicators

When you press a function button (such as

STOP), the selected function’s indicator (such

as STOP) appears on the TV screen for about

4 seconds. When you change the channel, the

new channel number appears on the TV

screen for about 4 seconds.

Follow these steps to have the VCR automati-

cally memorize the beginning and end of com-

mercials while it records a program, so it can

mark the tape later.

1. Press MENU to display the main menu.

2. Repeatedly press PLAY or STOP to high-

Note: If you play back a poor quality or dam-

aged tape, the function indicator might not ap-

pear.

light SETUPVCR, then press FF.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 28 Tuesday, July 20, 1999 5:13 PM

3. If necessary, repeatedly press PLAY or

STOP to highlight SET UP COMMER-

CIAL ADV..

memory becomes full, the remaining com-

mercials are not marked.

• The Commercial Advance feature turns off

if there is a power failure.

VCR

• If you rewind the tape and start another

recording before power is turned off, com-

mercials might not be correctly marked.

ADV.

Marking an Unmarked Tape

4. Press FF. You see:

You can go back and add Commercial Ad-

vance markings to a tape you’ve already re-

corded.

CIAL ADV.

OFF

AUTO

TAPE.

1. Insert the tape on which you want to add

the marking(s). Be sure the erase-protec-

tion tab is in place (see “Erase Protection”

on Page 32).

5. Repeatedly press PLAY or STOP to high-

light C/A RECORD, then press FF to

select ONor OFF.

2. Use FF or REW to position the tape to a

point 2 to 3 minutes before the first com-

mercial begins.

ON — With this setting, when you press

STOP to end a recording, the VCR prompts

you, when you stop recording or turn the

VCR off, to have commercials marked.

3. Press MENU to display the main menu.

4. Repeatedly press PLAY or STOP to high-

light SETUPVCR, then press FF.

OFF— The VCR does not mark commer-

cials.

5. Repeatedly press PLAY or STOP to high-

light SET UP COMMERCIAL ADV., then

press FF.

6. When you finish setting up Commercial

Advance, press MENU three times.

6. Repeatedly press PLAY or STOP to high-

light MARK UNMARKED TAPE., then

press FF. STARTMARKINGFROM CUR-

RENTTAPEPOSITION.appears.

Notes:

• It takes several minutes for the VCR to

mark the recording.

7. Press PLAY and let the recording play to

the end. CA flashes on the VCR’s display.

Press STOP twice at the end of the record-

ing. The VCR rewinds the tape, displays

NOWMARKINGCOMMERCIALSon the TV

screen for a few seconds, then searches

for and marks the commercial portion(s).

• The VCR marks commercials in a timer

recording after the recording stops (see

“Automatic Timer Recording” on Page 37).

• If the interval between two timer recordings

is not long enough to allow commercial

marking, the VCR waits until after the next

timer recording.

Notes:

• CA continues to flash on the VCR’s dis-

play until the VCR has finished marking

commercials.

• The VCR can store up to eight timer

recording settings or 40 commercial loca-

tions in memory at one time. When the

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 29 Tuesday, July 20, 1999 5:13 PM

• The recording must be at least 15 min-

utes long for the VCR to detect the com-

mercials. If you press STOP before the

tape plays 15 minutes, AT LEAST 15

MIN SEARCHING NEEDED FOR

MARKING appears.

Questions and Answers about

Commercial Advance

Question

Answer

How fast does the

The VCR advances

VCR advance through through 3 minutes of

commercials?

commercials in about

8 to 12 seconds if the

tape speed is EP (see

“Recording Speeds/

Tape Selection” on

Page 32). If it is SP, it

takes about 25 to 35

seconds.

Playing Back with Commercial

Advance Marking

Follow these steps to select how the VCR op-

erates when you play any marked tape.

1. Press MENU to display the main menu.

Are commercials still Yes.

recorded on the tape?

2. Repeatedly press PLAY or STOP to high-

light SETUPVCR, then press FF.

Does Commercial

Advance work at all

recording speeds?

Yes.

3. Repeatedly press PLAY or STOP to high-

light SET UP COMMERCIAL ADV., then

press FF.

Does Commercial

Advance still work if I

remove the tape from

the VCR and then

play it back later?

Yes.

4. Repeatedly press PLAY or STOP to

highlight C/APLAYBACK, then press FF

to select AUTOor MANUAL.

AUTO — The VCR automatically skips

marked commercial blocks.

Can I play a Commer- Yes, but commercials

cial Advance marked will only be skipped if

tape in another VCR? the other VCR also

has Commercial

MANUAL — The VCR skips commercials

only when you press C/A SKIP/ZERO during

playback.

Advance.

Can I mark a record- Yes. See “Marking an

ing that was made on Unmarked Tape” on

5. When you finish, press MENU three times

to exit.

another VCR?

Page 28.

Notes:

• Commercial Advance might not detect all

commercials.

SKIPPING/SELECTING

PREVIEWS

• Commercial Advance might skip part of a

program if there are frequent dark and

quiet scenes.

Your VCR’s Movie Advance feature lets you

skip the previews at the beginning of many pur-

chased or rented movies, or select a specific

preview to watch.

Movie Advance works only with tapes

Note:

recorded in the SP speed that have the

erase-protection tab removed.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 30 Tuesday, July 20, 1999 5:13 PM

1. Load a tape. When the VCR automatically

USING INDEX SEARCH

starts playback, press STOP.

Your VCR has the VHS Index Search System.

Each time you start recording, the VCR auto-

matically marks the tape with an index mark at

that location. You can locate the recording you

want to play or skip the recording(s) you don’t

want to watch by either entering the number of

index marks or by scanning. The VCR searches

forward or backward from the current location.

2. Press INDEX/M/A SKIP. You see:

MODE

3. Repeatedly press PLAY or STOP to high-

Notes:

light MOVIE ADVANCE, then press FF.

• Since the VCR does not display the index

marks, we recommend you list the record-

ings on each tape in order on the tape’s

box, to make it easier to locate a particular

recording on the tape.

4. Repeatedly press PLAY or STOP to se-

lect GO TO START OF MOVIEor GO TO

PREVIEW.

NCE

• Index search might not function properly

when two or more index marks are close to

each other.

• If you do not press any button within 10

seconds after you select INDEXSEARCH,

the VCR cancels the index search mode.

GO TO START OF MOVIE — The VCR

automatically skips any previews at the

beginning of the tape and advances to the

start of the movie.

• If you activate the direct access index

search at a tape position very close to an

index mark, the VCR might not count that

mark. See “Direct Access Index Search.”

GO TO PREVIEW — The VCR searches

for and plays the first preview.

• Recording over an index mark erases that

index mark.

Press INDEX/M/A SKIP to skip to the next

preview.

5. Press FF.

Direct Access Index Search

1. Press INDEX/M/A SKIP while the VCR is

stopped or playing a tape. You see:

MODE

2. Repeatedly press PLAY or STOP to

highlight INDEX SEARCH, then press

FF. INDEX appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 31 Tuesday, July 20, 1999 5:13 PM

EARCH

3. Use the number keys to enter the number

of index marks you want to skip.

4. When you see the recording you want,

press PLAY. Normal playback starts.

For example, if the tape is at the second re-

cording (index mark 2) and you want to watch

the seventh recording (at index mark 7), enter 5

to skip past index marks 3 through 6. Or, if the

tape is at index mark 9 and you want to watch

the recording at index mark 3, enter 7 to skip

backward past index marks 9 through 4.

REPEAT PLAY

You can automatically repeat playback of a

tape from the beginning to the end (or to a

blank part), instead of having the tape automat-

ically rewind and eject.

1. While the tape is stopped, press MENU to

Then press FF to skip forward to that index

mark or REW to skip backward. When the tape

reaches the selected index mark, the VCR

starts normal playback.

display the main menu.

2. Repeatedly press PLAY or STOP to high-

light SETUPVCR, then press FF. The VCR

highlights REPEATPLAY.

Index Scan

3. Press FF so ONappears.

1. Press INDEX/M/A SKIP while the VCR is

VCR

stopped or playing a tape.

2. Repeatedly press PLAY or STOP to

highlight INDEX SEARCH, then press

FF. INDEXappears.

4. Press MENU twice to exit the menu.

5. Press PLAY to start repeat playback. REP

appears.

The VCR repeats playback from the beginning

to the end of the tape, or to the first unrecorded

portion that is at least 30 seconds long. AUTO

REPEAT appears while the VCR rewinds the

tape to the beginning.

3. Press FF or REW to start the scan. AUTO

INDEX SEARCH appears and the VCR

starts to fast-forward or rewind. As the tape

passes an index mark, the VCR enters the

visual search mode for 10 seconds, then

resumes the fast-forward or rewind.

Once you select the repeat play mode, it re-

mains on even after you turn off the VCR. To

turn off repeat play, repeat Steps 1–4 and se-

lect OFFin Step 3.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 32 Tuesday, July 20, 1999 5:13 PM

RECORDING

There are four ways to record using your VCR:

Although T-160 video cassettes offer the long-

est recording time, they contain thinner tape

that is more likely to jam. We suggest you use

T-120 or shorter length tape.

• Immediate recording — to record a broad-

cast as you watch it or record one program

on the VCR while you watch another on

the TV.

The following chart shows the maximum re-

cording times for different-length tapes at the

recording speeds.

• VCR Plus+ recording — to record a broad-

cast using the VCR’s VCR Plus+ feature.

• Automatic timer recording — to record a

broadcast at a time you set.

TAPE

LENGTH

1 hour

• Dubbing — to record from another tape or

video source.

T-60

2 hours

3 hours

(60 min.)

(120 min.)

(180 min.)

Notes:

T-120

T-160

2 hours

(120 min.)

4 hours

(240 min.)

6 hours

(360 min.)

• Your VCR automatically records the audio

signal and adjusts the sound level while it

records.

2²/³hours

(160 min.)

5¹/³hours

(320 min.)

8 hours

(480 min.)

• The video cassette you use for recording

must have the erase-protection tab in

place. If the tab is removed, the cassette

automatically ejects if you try to record on it

(see “Erase Protection”).

ERASE PROTECTION

Video cassettes have an erase-protection tab

to prevent accidental erasure of a tape. To pre-

vent recording, break off the tab using a screw-

driver. The cassette automatically ejects if you

try to record on the tape.

RECORDING SPEEDS/TAPE

SELECTION

This VCR can record at three speeds: SP

(standard play), LP (long play), and EP (ex-

tended play).

SP is the fastest recording speed and results in

the highest quality picture. LP and EP record

more slowly and use less tape, but the picture

quality is not as high as a recording made at

the SP speed.

If you want to record on a video cassette that

does not have the tab, put a piece of heavy

plastic tape over the erase-protection tab hole.

The quality of tape you use greatly affects

record/playback quality and the life of the VCR.

Use only video cassettes that display the offi-

cial

logo. High-grade tape has a better ox-

ide coating that helps prevent dirty video heads

and gives the best results.

Tape

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 33 Tuesday, July 20, 1999 5:13 PM

audio mode when the broadcast has a stereo or

SAP/Hi-Fi

arrow mark points to the desired mode.

SELECTING THE SIGNAL

TO RECORD

SAP signal, repeatedly press

until the

You can select the signal to record — from the

IN FROM ANT.

source connected to the

jack or an

IMMEDIATE RECORDING

audio/video source — in either of these ways.

INPUT

• Repeatedly press

until the desired

Recording a Program

as You Watch It

input source appears — LINE1 (or

LINE2) for an audio/video source, or a

channel number for broadcast signals.

Follow these steps to record a program as you

watch it. If you know how long the program is,

you can set how long the VCR records so it

stops recording automatically.

• Repeatedly press

s or t to set the VCR

to the desired broadcast channel, or to one

channel higher than the highest channel

number (or one channel lower than the

lowest channel number) for an audio/video

source.

Note: If you are watching the program on a TV/

monitor that is connected to the VCR’s

R-

AUDIO-L/VIDEO OUT

jacks, set the TV/monitor

to the video mode and skip Steps 2 and 3.

Note: Select LINE1for recording signals from

1. Turn on the VCR and the TV.

R-AUDIO-L IN 1/VIDEO IN 1

the back

jacks, or

AV2

LINE2for recording signals from the front

jacks.

2. Set the TV’s tuner to the same channel as

3 CH. 4

on the back of the VCR.

TV/VCR

3. Press

until VCR appears.

RECEIVING/RECORDING

STEREO/SAP BROADCASTS

(MODEL 63 ONLY)

4. Load a blank cassette, or one that you

want to record over, into the VCR.

SPEED

5. Repeatedly press

on the remote

control until the desired recording speed

(SP, LP, or EP) appears.

The Model 63 has three channels for audio re-

cording — two (left and right) stereo channels

on the Hi-Fi track, and one monaural channel

on the standard track.

6. Select the signal to record (see “Selecting

the Signal to Record”).

7. (Model 63 only) Set the audio recording

mode to the desired setting. See “Receiv-

ing/Recording Stereo/SAP Broadcasts

(Model 63 Only)”.

DISP/ENT

Press

to display the audio programs

available on the broadcast you are currently

tuned to. STEREO, SAP, and MONOappear on

the TV screen, and STEREO and/or SAP might

appear on the VCR’s display. On the TV

screen, parenthesis appear around each type

of audio signal that is not available. For exam-

ple, if a station broadcasts mono (monaural)

and SAP signals, (STEREO), SAP, and MONO

appear on the TV screen and SAP appears on

the VCR’s display.

REC/TIME

8. Press

. The VCR starts to record

and the following appears on the TV

screen:

REC

TO SET SPEC

PLEASE PUSH REC KEY

C REC T

The arrow to the right of the audio mode display

indicates the current audio mode. To select the

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 34 Tuesday, July 20, 1999 5:13 PM

Note: To record without a set recording

length, skip Step 9.

RECORDING WITH VCR PLUS+

The VCR’s VCR Plus+ feature lets you easily

record TV programs by using the PlusCodes

shown in most TV program listings.

REC/TIME

9. Press

length appears on the TV screen. Repeat-

REC/TIME

again. The recording

edly press

to advance the timer

to the desired recording length. The

recording length advances in 30-minute

increments up to 2 hours, then in 1-hour

increments up to 4 hours.

Setting the VCR Plus+ Guide

Channels

Notes:

Most television guides contain a list of two-digit

numbers called guide channels or VCR Plus+

channel numbers. Each broadcast/cable TV

channel is assigned one of these numbers.

• To ensure that you record the entire pro-

gram, set the recording length to longer

than the program length.

• To display the remaining recording time,

Notes:

DISP/ENT

press

• To temporarily stop the tape during a

PAUSE PAUSE

during a timed recording.

• Before you can record using VCR Plus+,

you must first set the VCR’s guide chan-

nels so your VCR can recognize the Plus-

Codes published in your television guide.

recording, press

. Press

again to resume recording. If you leave

the VCR paused for about 5 minutes,

the VCR automatically stops.

• You can find a guide channel listing for

your area in the TV section of most Sunday

newspapers and other TV listings. In some

listings, the guide channel numbers are

listed next to the station’s call letters.

• If the cassette’s erase protection tab has

been removed, the VCR ejects the cas-

sette and CHECK CASSETTE RECORD

TAB appears. Use another cassette, or

place a piece of heavy plastic tape over

the erase-protection tab hole.

• You only need to set the VCR Plus+ guide

channels once. The channels stay in mem-

ory even if the VCR’s power is interrupted

for an extended period of time.

STOP

10. Press

to stop recording at any time.

• Before you start, be sure you have com-

pleted all connections, set the clock, set the

on-screen programming language, selected

the input signal, and programmed all the

channels available in your area.

Recording One Program on the VCR

While You Watch Another on the TV

–

1. Follow Steps 1 9 of “Recording a Program

as You Watch It” on Page 33.

TV/VCR

2. Repeatedly press

pears.

until VCR disap-

Follow these steps to set the guide channels.

1. Using the list of guide channels in your

television guide as a reference, write down

the following information about each sta-

tion in your area:

Note: If you are watching the program on a

TV/monitor that is connected to the VCR’s

R-AUDIO-L/VIDEO OUT

jacks, set the TV/

monitor to the TV mode.

• Station name/call letters

3. Set the TV tuner to the channel you want to

watch.

• Guide channel number for the station

• Channel number you select on the TV or

VCR to tune the station

STOP

4. Press

to stop recording at any time.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 35 Tuesday, July 20, 1999 5:13 PM

2. For each station, compare the station’s

guide channel number with the number

you select on the TV or VCR to tune to the

station. If the numbers match, cross that

station off of the list.

PLAY or STOP to change the number or

ADD/DLT to delete it.

10. When you finish, press MENU three times

to exit.

3. If a tape is playing, press STOP.

Timer Recording with VCR Plus+

4. Press MENU to display the main menu.

Most television guides list a 1- to 8-digit num-

ber called a PlusCode next to many of the

listed programs. You can use these PlusCodes

to easily program your VCR to record broad-

casts.

5. Repeatedly press PLAY or STOP to highlight

SETUPCHANNEL, then press FF.

6. Repeatedly press PLAY or STOP to high-

light VCR Plus+CHSETUP, then press

FF.

You can set the VCR to record as many as

eight broadcasts, including any timer programs

you want to set up (see “Automatic Timer Re-

cording” on Page 37).

The following appears on the TV screen if

you selected a cable box or DSS receiver

as your input source.

H SET UP

ATV

You can set the VCR to record at any time on a

specific day, at the same time each week, or

the same time Monday through Friday.

Before you start, be sure you have set the VCR

Plus+ guide channels for your area (see “Set-

ting the VCR Plus+ Guide Channels” on

Page 34).

The following appears on the TV screen if

you selected an external antenna as your

input source.

VCR

GU DE CH

us+

H SET UP

The VCR can record only one broadcast

Note:

at a time. If you schedule recording of broad-

casts on different channels that start at the

same time, the VCR records the lowest timer

number. For more information about timer

numbers, see “Setting a Timer” on Page 38.

SELECT

SET

KEY

MENU KEY

END

7. Press PLAY or STOP to highlight the guide

channel you want to set, then press FF. The

cursor moves to the right of the guide

channel you selected.

1. Turn on the TV and set it to the same chan-

nel as the VCR’s 3 CH. 4 switch.

If you are using a TV/monitor that is

Note:

connected to the VCR’s R-AUDIO-L/VIDEO

OUT jacks, set it to the video mode.

8. Repeatedly press PLAY or STOP to select a

CATV CH or TV CH number. Then press

REW to set the number.

2. Insert a blank cassette, or one that you

want to record over, into the VCR. The

VCR turns on.

9. Repeat Steps 7 and 8 for each remaining

channel number.

3. Repeatedly press TV/VCR until VCR

If the channel number is not correct, re-

peatedly press PLAY or STOP then FF to

select the correct number. Then press

appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 36 Tuesday, July 20, 1999 5:13 PM

4. Press PROG. You see:

If you make a mistake while entering

Note:

a PlusCode, repeatedly press REW to

delete the PlusCode number, then enter

the correct numbers.

SET PROGRAM

VCR

us+

PROGRAM

MER PROGRAM

7. Press PROG. You see:

SELE

SET

END

KEY

NU KEY

VCR

us+

LY (

EEKLY

-FR

)

If the clock is not set, PLEASESET

Note:

CLOCK BEFORE PROGRAMMING ap-

pears, then the clock-setting screen ap-

pears. Set the clock as described in “Man-

ually Setting the Clock” on Page 16, then

continue with Step 5.

SELE

T PUSH 1, 2

END

PROG KEY

8. Press 1, 2, or 3 on the remote control to

select the desired program mode. You see

the recording time and date corresponding

to the PlusCode you entered.

5. Press PLAY or STOP to highlight VCR

Plus+PROGRAM, then press FF. You see

the PlusCode entry screen.

00P

125

SLP

NUMBER

SPEED

KEYS

KEY

Notes

If you try to enter more than eight

Note:

timer programs, you see:

• INVALID ENTRY flashes under the

PlusCode on the TV screen for either of

the following reasons:

TIMER PROGRAMS ARE FULL

TO ENTER A NEW PROGRAM

PLEASE ERASE ONE PROGRAM

— Invalid PlusCode

— The PlusCode and program mode do

not match (such as entering a Plus-

Code for a Saturday broadcast and

selecting the DAILY (Monday-Friday)

program mode).

See “Clearing a Timer” on Page 40.

6. Find the PlusCode in your television guide

for the broadcast you want to record, then

use the number keys on the remote control

to enter the PlusCode.

• To erase a VCR Plus+ program, press

ADD/DLT.

9. If you want to change the displayed tape

speed, press SPEED on the remote control

until the speed you want (SP, LP, or EP)

appears.

NUMBER

EYS

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 37 Tuesday, July 20, 1999 5:13 PM

10. Press PROG twice. TURN VCR OFF FOR

TIMER RECORDING appears on the TV

screen. (If you connected a cable box to

the VCR, AND LEAVE CABLE BOX

POWERONalso appears).

3. Press PROG. You see:

RAM

GRAM

11. Repeat Steps 4–10 for each PlusCode you

want to enter.

12. Press POWER to turn off the VCR’s power.

4. Repeatedly press PLAY or STOP to select

TIMERPROGRAM, then press FF. The first

four timer settings appear.

TIMERappears.

Important:

STOP CH SPD

2 : 00

08 SP

• Be sure that the VCR displays TIMER

when you turn it off. If it does not appear,

check your programming.

• If you set the VCR to record a CATV pro-

gram through a cable box, be sure to leave

the cable box turned on before the timer

program starts.

5. Repeatedly press PLAY or STOP to select

the setting you want to change, then press

FF.

• If you did not set the VCR to select chan-

nels on your cable box, be sure to leave

the cable box turned on and set it to the

channel you want to record. See “Setting

the Cable Box” on Page 19.

6. Follow Steps 9–13 under “Setting a Timer”

on Page 38 to correct the selected setting.

7. When you finish, press PROG again, then

turn off the VCR.

• The VCR only records with VCR Plus+

when the VCR is off at the recording start

time.

AUTOMATIC TIMER

RECORDING

Checking/Changing VCR Plus+

Programs

The VCR’s automatic timer lets you program it

to select an input source, start recording from

that source at a time you set, then stop record-

ing at a time you set. You can set up to eight

timers to record any combination of weekly,

daily, or one-time events.

1. Turn on the TV and set it to the same chan-

nel as 3 CH. 4 on the back of the VCR.

If you are using a TV/monitor that is

Note:

connected to the VCR’s R-AUDIO-L/VIDEO

OUT jacks, set the TV/monitor to the video

mode.

You can set the VCR to record at any time on a

specific day within a 1-month period, at the

same time Monday through Friday (DAILY), or

at the same time on the same day every week

(WEEKLY).

2. Turn on the VCR and repeatedly press TV/

VCR until VCR appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 38 Tuesday, July 20, 1999 5:13 PM

Notes:

4. (Model 63 only) Set the audio recording

mode to the desired setting. See “Receiv-

ing/Recording Stereo/SAP Broadcasts

(Model 63 Only)” on Page 33.

• The VCR can record only one broadcast at

a time. If you set the VCR’s timer to record

broadcasts on different channels that start

at the same time, the VCR only records the

broadcast that has the lowest timer num-

ber (see “Checking/Changing Timers” on

Page 40).

5. Load a blank cassette, or one that you

want to record over, into the VCR.

PROG

6. Press

. You see:

RAM

• If two timer settings overlap, the one that

starts first has priority. The VCR begins

recording the second broadcast after the

set time for the first broadcast is over.

GRAM

• The VCR must be off at the start time you

set for it to begin an automatic timer

recording.

PLAY

STOP

to select

7. Repeatedly press

TIMERPROGRAM, then press . The cur-

rent settings for up to the first four broad-

casts appear.

• If there is a power failure of more than 30

minutes during a timer recording, the

recording does not resume after power is

restored.

STOP CH SPD

2 : 00

08 SP

• If there is a power failure of more than 30

minutes before a start time, the VCR loses

the clock setting and therefore does not

start automatic timer recording. However, if

you have an EDS channel in your area and

have set the VCR to automatically set the

clock from the EDS signal, the clock is

reset within 10 minutes after power is

restored and you turn on the VCR, and the

VCR records at the set time(s).

Note: If the clock is not set, PLEASE SET

CLOCKBEFOREPROGRAMMINGappears,

then the clock setting screen appears. Set

the clock as described in “Manually Setting

the Clock” on Page 16, then continue with

Step 8.

Setting a Timer

PLAY

8. Repeatedly press or hold down

STOP

to select an empty timer number,

Note: If you use a TV/monitor that is connected

then press

appears.

The following menu

R-AUDIO-L/VIDEO OUT

to the VCR’s

jacks, set

the TV/monitor to the video mode and skip

Steps 2 and 3.

DATE

START

8 SAT --:-- --:-- --

TODAY

SE EC

1. Turn on the VCR and the TV.

START

DATE

SELECT

SET

END

KEY

PROG KEY

3 CH. 4

2. Set the TV to the same channel as

on the back of the VCR.

TV/VCR

3. Repeatedly press

appears.

until VCR

PLAY

9. Repeatedly press or hold down

to select the date when you want to

record.

STOP

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 39 Tuesday, July 20, 1999 5:13 PM

To record a broadcast at the same time on

the same day every week, press either but-

ton until WEEKLY flashes and the desired

day of the week appears.

To record from a source connected to the

R-AUDIO-L IN 1/VIDEO IN 1 (or AV2 for the

Model 63) jacks, repeatedly press PLAY or

STOP until LINE (LINE1 or LINE2 on

the Model 63) appears. Then press FF.

DATE

START

13. Repeatedly press PLAY or STOP to select

the tape speed (SP, LP, or EP). Then press

FF.

WEEKLY

SUN

--:-- --:-- --

LECT

START

DATE

T :

KEY

PROG KEY

SET

END

14. Double-check all the set information.

• If the information is correct, press PROG.

To record a broadcast at the same time

Monday through Friday, press either button

until DAILY flashes and MON-FRI

appears.

• If an entry is not correct, repeatedly

press FF or REW to move the cursor to

the incorrect entry, enter the correct

information, then press PROG.

DATE

START

The timer settings appear on the TV

screen. To enter another setting, repeat-

edly press PLAY or STOP to select another

timer number and repeat Steps 7–13.

DAILY

--:-- --:-- --

MON-FRI

SELECT

START

DATE

T :

KEY

PROG KEY

SET

END

15. Press PROG again. TURN VCR OFF FOR

TIMERRECORDINGbriefly appears.

To record a broadcast at a set time today,

press either button until today’s date

flashes and TODAYappears.

16. Press POWER to turn off the VCR. TIMER

appears.

DATE

START

Important:

8 SAT --:-- --:-- --

TODAY

SE EC

• Be sure that TIMER appears when you

turn the VCR off. If it does not appear,

check your entries.

START

DATE

SELECT

SET

KEY

PROG KEY

END

• If you load a cassette with its erase-

protection tab removed and set the VCR’s

timer, the VCR ejects the cassette and

To record a broadcast at a specific time

and date, repeatedly press PLAY or STOP

to select the specific date.

^TIMERand

flash.

• If you set up the VCR to record a cable

broadcast through a cable box, be sure to

leave the cable box turned on and tuned to

the desired station before the broadcast

starts.

Press FF to store your selection.

10. Repeatedly press or hold down PLAY or

STOP to select the start hour. When the

correct hour appears, press FF. Then

repeatedly press PLAY or STOP to select

the minute and press FF.

• You can manually turn on and operate the

VCR before the set times, but the VCR

starts an automatic timer recording only if

the power is off at the set start time.

11. Repeat Step 9 to set the stop time.

12. Repeatedly press or hold down PLAY or

STOP to select the channel. Then press FF.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 40 Tuesday, July 20, 1999 5:13 PM

Monitoring an Automatic Timer

Recording

Clearing a Timer

If the timer recording has not yet started:

1. Turn on the TV and set it to the same chan-

nel as 3 CH. 4 on the back of the VCR.

Note: If you are using a TV/monitor that is

connected to the VCR’s R-AUDIO-L/VIDEO

OUT jacks, set the TV/monitor to the video

mode.

Note: If you are using a TV/monitor that is

connected to the VCR’s R-AUDIO-L/VIDEO

OUT jacks, set the TV/monitor to the video

mode.

2. Press TV/VCR until VCR appears.

2. Turn on the VCR and repeatedly press TV/

VCR until VCR appears.

Checking/Changing Timers

3. Press PROG. You see the set program

menu.

1. Turn on the TV and set it to the same chan-

4. Repeatedly press PLAY or STOP to select

TIMERPROGRAM, then press FF. The first

four timer settings appear.

nel as 3 CH. 4 on the back of the VCR.

Note: If you are using a TV/monitor that is

connected to the VCR’s R-AUDIO-L/VIDEO

OUT jacks, set the TV/monitor to the video

mode.

STOP CH SPD

2 : 00

08 SP

2. Turn on the VCR and repeatedly press TV/

VCR until VCR appears.

3. Press PROG. You see the set program

menu.

5. Repeatedly press PLAY or STOP to select

the setting you want to clear, then press

ADD/DLT.

4. Repeatedly press PLAY or STOP to select

TIMERPROGRAM, then press FF. The first

four timer settings appear.

6. When you finish clearing the timer, press

PROG.

STOP CH SPD

2 : 00

08 SP

Turn off the VCR if you still have at least one

timer setting entered.

If a timer recording is in progress:

1. Press POWER to stop timer recording. TO

CANCEL TIMER REC PUSH POWER

THEN STOP KEY appears if you are

watching the signal from the VCR.

5. Repeatedly press PLAY or STOP to select

the setting you want to change, then press

FF.

6. Follow Steps 9–13 under “Setting a Timer”

on Page 38 to correct the selected setting.

2. Within 10 seconds, press POWER then

press STOP. TIMER disappears.

7. When you finish, press PROG again, then

turn off the VCR.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 41 Tuesday, July 20, 1999 5:13 PM

DUBBING

AUDIO-ONLY RECORDING

(MODEL 63 ONLY)

The process of recording from one audio/video

device to another is called dubbing.

Because of the superior quality of VHS Hi-Fi

audio recordings, you might want to use your

VCR as an audio-only recorder. You can also

make live recordings by connecting a pre-

An audio/video device where a signal origi-

nates is called the dubbing source. You can

use another VCR, camcorder, satellite receiv-

er, or other device with A/V outputs as the dub-

bing source, connect the dubbing source and

the VCR, then use your VCR to record the sig-

nal from the dubbing source. Or, you can use

this VCR as the dubbing source for another

VCR. See “Installation” on Page 9 for the vari-

ous possible connections.

AUDIO IN

amplifier or mixer to the VCR’s

jacks.

Simply select the line input and record as usu-

al.

Caution: Do not directly connect a microphone

to the VCR.

Note: For the best audio fidelity, we recom-

mend you use high-quality video tape (such as

Cat. No. 44-465) to make audio-only record-

ings.

Note: Always use video-quality shielded ca-

bles with phono-type connectors to connect the

device to the VCR. Do not use standard audio

patch cords.

Important: Most material performed in public,

such as concerts, plays, and movies, or distrib-

uted on prerecorded video tapes is copyright-

ed. The unauthorized recording or duplication

of copyrighted material is a violation of the

plication may result in fines, imprisonment, or

both. Note, however, that in the United States,

it is not a violation of U.S. copyright laws for a

consumer to record a broadcast television pro-

gram for private (in-home) viewing.

To dub a tape, start playback on the dubbing

source first (see that device’s instructions) then

start recording on the recording VCR.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 42 Tuesday, July 20, 1999 5:13 PM

ADDITIONAL INFORMATION

TROUBLESHOOTING

If you follow the instructions in this manual and still have trouble operating your VCR, look in this

chart for the problem description and its solution. If your VCR still does not work properly, contact

your local RadioShack store.

PROBLEM

No power.

POSSIBLE SOLUTION

The power cord is not connected. Plug the power cord into an AC

outlet.

Timer recording did not work, The power is on. Turn off the power.

or a broadcast was recorded

at the wrong time.

The timer is not set or is set incorrectly. Check the timer settings.

VCR Plus+ recording did not The power is on. Turn off the power.

work, or a broadcast was re-

corded at the wrong time or VCR Plus+ is not set or is set incorrectly. Check the VCR Plus+

on the wrong channel.

settings.

The guide channels are not set correctly. Check the guide channel

settings.

Cannot record.

The erase-protection tab is missing. Place a piece of tape over the

tab hole.

Picture is poor on playback. The TV is not set to the proper channel. Set the TV to Channel 3 or

The TV’s fine tuning is not set correctly. Fine tune your TV.

Audio/video connections are incorrect. Check all connections.

The playback picture is dis- The video heads are dirty. See “Cleaning the Video Heads” on

torted.

Page 45.

The VCR might not have adjusted the tracking correctly. You

might need to manually adjust tracking (see “Tracking” on

Page 26).

No picture on playback.

The TV is not set to the proper channel. Set it to Channel 3 or 4, or

to its audio/video input if you connected it to the VCR’s R-AUDIO-L/

VIDEO OUT jacks.

Audio/video connections are incorrect. Check all connections.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 43 Tuesday, July 20, 1999 5:13 PM

PROBLEM

POSSIBLE SOLUTION

Remote control buttons do

Something is blocking the path from the remote control to the

not work when the power is VCR.

on and a cassette is loaded.

Bright light is shining on the VCR’s remote control sensor window.

Block the source of the light, get closer to the VCR, or change the

VCR’s location.

The remote control might be set for another device’s operation.

Press VCR then try again.

The remote control’s batteries might be weak. Replace the batter-

ies.

Cannot see broadcast TV

programs using the VCR’s

tuner.

TV/VCR is not set correctly. Repeatedly press TV/VCR until VCR

appears.

Audio/video connections are incorrect. Check all connections.

Cannot record from the input Connections are incorrect. Check all connections.

jacks.

INPUTis not set correctly. Select LINE1or LINE2.

No stereo sound for a stereo You have not connected the VCR’s AUDIO OUT jacks to a stereo

recording (Model 63 only).

system or stereo TV. Connect the jacks to a stereo output.

The audio out setting is not correctly set. Set it to Hi-Fi— see

“Receiving/Recording Stereo/SAP Broadcasts (Model 63 Only)”

on Page 33.

The VCR might not have adjusted the tracking correctly. You

might need to manually adjust tracking (see “Tracking” on

Page 26).

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 44 Tuesday, July 20, 1999 5:13 PM

CARE AND MAINTENANCE

Your Optimus 4-Head VHS HQ VCR is an example of superior design and craftsmanship. The fol-

lowing suggestions will help you care for your VCR so you can enjoy it for years.

Keep the VCR dry. If it gets wet, wipe it dry immediately. Liquids might contain min-

erals that can corrode the electronic circuits.

Use and store the VCR only in normal temperature environments. Temperature ex-

tremes can shorten the life of electronic devices and distort or melt plastic parts.

Keep the VCR away from dust and dirt, which can cause premature wear of parts.

Handle the VCR gently and carefully. Dropping it can damage circuit boards and cas-

es and can cause the VCR to work improperly.

Use only fresh batteries of the required size and type in the remote control. Batteries

can leak chemicals that damage your VCR remote control’s electronic parts.

Wipe the VCR with a damp cloth occasionally to keep it looking new. Do not use

harsh chemicals, cleaning solvents, or strong detergents to clean the VCR.

Modifying or tampering with the VCR’s internal components can cause a malfunction, invalidating

your VCR’s warranty and voiding your FCC authorization to operate it. If your VCR is not performing

as it should, take it to your local RadioShack store for assistance.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 45 Tuesday, July 20, 1999 5:13 PM

Servicing Your VCR

Storing Your Video Cassettes

There are no user-serviceable parts inside your

VCR. If you encounter a problem that you can-

not correct using this manual and its trouble-

shooting guide, take the VCR to your local

RadioShack store for assistance.

Unless you are making an automatic timer re-

cording, eject and store the cassette before

you turn off the VCR. This helps protect the

cassette and the VCR’s internal mechanisms.

Place your video cassettes in their protective

boxes and store them in a cool, dry, dust-free

environment. Store the cassettes on end, not

on their sides, to prevent improper settling of

the cassette’s spools.

Cleaning the Video Heads

When video head cleaning becomes neces-

sary, the following message appears on the TV

screen while playing back a recorded tape.

Note: Tape can become wound too tightly

around the cassette’s spools after many play-

ings. This can make the cassette load improp-

erly and automatically eject when you insert it.

On most cassettes there is a brake-release

plunger on the bottom center of the cassette.

Use the tip of a pen or pencil to press the

plunger. This loosens the tape.

Video head cleaning kits are available from

your local RadioShack store. Clean the heads

only when the VCR displays the message

shown above. Be sure to use the “dry” type

cleaning cassette.

Serious problems require cleaning by a trained

technician. For more head cleaning informa-

tion, contact your local RadioShack store.

Brake-Release Plunger

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 46 Tuesday, July 20, 1999 5:13 PM

SPECIFICATIONS

Television System .............................................................................. NTSC Standard Color Signal

Recording System ................................................................................ Four-Head Double Azimuth

Tape Width ........................................................................................................................... /²Inch

Tape Speed:

SP ............................................................................................ 1.31 Inch/second (33.35 mm/s)

LP ............................................................................................ 0.65 Inch/second (16.67 mm/s)

EP .......................................................................................... 0.43 Inch/second (11.125 mm/s)

Tuner Channels:

VHF .................................................................................................................................. 2–13

UHF ................................................................................................................................ 14–69

CATV .............................................................................................................................. 1–125

RF Converter ............................................................................................... Built-in VHF Converter

Converter Output ..................................................................................................... Channel 3 or 4

Terminals:

Antenna Input ................................................................................................VHF/UHF: F Type

Antenna Output ............................................................................................ VHF/UHF: F Type

Video Input/Output ........................................................................................ Phono Connector

Audio Input/Output ........................................................................................ Phono Connector

Video Output Level ............................................................................................................. 1.0 V

p-p

Video Output Impedance ......................................................................................................... 75 Ω

Audio Output Level .............................................................................................................. –8 dBV

Audio Output Impedance ..........................................................................................................1 kΩ

Video Input Level .......................................................................................................... 0.5-1.5 V

p-p

Video Input Impedance .......................................................................................................... 75 kΩ

Audio Input Level ............................................................................................................... –10 dBV

Audio Input Impedance .......................................................................................................... 50 kΩ

Video S/N Ratio (weighted):

SP .................................................................................................................................... 43 dB

EP .................................................................................................................................... 41 dB

Audio S/N Ratio:

Regular Audio (weighted)

SP .................................................................................................................................... 42 dB

EP .................................................................................................................................... 40 dB

Hi-Fi Audio (Model 63 only) (Dynamic Range):

SP ................................................................................................................... More than 90 dB

LP ................................................................................................................... More than 90 dB

EP ................................................................................................................... More than 90 dB

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 47 Tuesday, July 20, 1999 5:13 PM

Frequency Response:

Regular Audio

SP ...................................................................................................................... 80 Hz–10 kHz

EP ........................................................................................................................ 80 Hz–5 kHz

Hi-Fi Audio (Model 63 only) In All Modes ........................................................... 20 Hz–20 kHz

Power Requirement ..................................................................................................... 120 V, 60 Hz

Power Consumption

Model 114 .................................................................................................................... 18 Watts

Model 63 ..................................................................................................................... 23 Watts

Dimensions (HWD) ................................................ 3⁵/⁸× 14¹⁵/¹⁶× 11¹³/¹⁶Inches (9.3 × 38 × 30 cm)

Weight ................................................................................................................ 7 lbs 8 oz (3.4 kg)

Specifications are typical; individual units might vary. Specifications are subject to change and

improvement without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 48 Tuesday, July 20, 1999 5:13 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 49 Tuesday, July 20, 1999 5:13 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 50 Tuesday, July 20, 1999 5:13 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 51 Tuesday, July 20, 1999 5:13 PM

Download from Www.Somanuals.com. All Manuals Search And Download.

16-551.fm Page 52 Tuesday, July 20, 1999 5:13 PM

Limited Ninety-Day Warranty

This product is warranted by RadioShack against manufacturing defects in material and workman-

ship under normal use for ninety (90) days from the date of purchase from RadioShack company-

owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED

HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,

INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES

CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL-

ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-

SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE

OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR-

RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-

NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD-

VISED OF THE POSSIBILITY OF SUCH DAMAGES.

Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-

cidental or consequential damages, so the above limitations or exclusions may not apply to you.

In the event of a product defect during the warranty period, take the product and the RadioShack

sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-

less otherwise provided by law: (a) correct the defect by product repair without charge for parts and

labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase

price. All replaced parts and products, and products on which a refund is made, become the prop-

erty of RadioShack. New or reconditioned parts and products may be used in the performance of

warranty service. Repaired or replaced parts and products are warranted for the remainder of the

original warranty period. You will be charged for repair or replacement of the product made after the

expiration of the warranty period.

This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,

accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or

maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs

other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as

fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs

of product removal, installation, set-up service adjustment or reinstallation.

This warranty gives you specific legal rights, and you may also have other rights which vary from

state to state.

RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102

We Service What We Sell

3/97

RadioShack

A Division of Tandy Corporation

Fort Worth, Texas 76102

7A7

Printed in Japan

Download from Www.Somanuals.com. All Manuals Search And Download.

Miele Dishwasher 05 714 400 User Manual
MTD Trimmer H70SS User Manual
Multiquip Welding System GLW 180H User Manual
Nokia Stereo System DIGITAL MULTIMEDIA TERMINAL User Manual
Novatel Automobile Alarm PowerPak II User Manual
Onkyo Speaker SL 107 User Manual
OPPO Digital Blu ray Player BDP 103 User Manual
Oster Convection Oven Oster Countertop Convection Oven User Manual
Panasonic Computer Monitor AG DVX100B User Manual
Panasonic VCR DS850 User Manual