TA-RW544/344
Ster eo Cassette Tape Deck
Instruction Manual
EJECT
DECK A/B RESET
EJECT
DECK
A
DECK
B
DUBB. STOP
2
MOTER COMPUTER CONTROL
AUTO REVERSE
2
MOTER COMPUTER CONTROL
AUTO REVERSE
/
/
POWER
PHONES
REVERSE MODE
DOLBY NR
DUBBING
REC BALANCE REC LEVEL
NORMAL
HIGH
L
R
MIN
MAX
ON
OFF
STEREO CASSETTE TAPE DECK TA-RW544
CONTENTS
Features................................................ 2
Important Safeguards........................... 3
Precautions .......................................... 3
Control Positions and Names .............. 4
Setting the Voltage Selector ................ 5
System Connections ............................ 5
Power Connections .............................. 5
To Play a Tape ..................................... 6
Useful Functions Available during Playback
Tape Dubbing .................................... 12
Useful Recording Functions .............. 13
Making Good Sound Recordings ...... 13
Connecting ONKYO Components
for z Components ........................... 14
CD Synchro Recording System ......... 14
Reverse Mode Function..................... 15
Handling Cassette Tapes ................... 16
Cassette Deck Maintenance............... 17
Specifications .................................... 17
Troubleshooting Guide ...................... 18
(TA-RW544 Only) ..............................................
7
Recording ............................................ 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safeguards
Precautions
1. Read Instructions — All the safety and operating instructions
1. Warranty Claim
should be read before the appliance is operated.
You can find the serial number on the rear panel of the unit. In
case of warranty claim, please report this number.
2. Recording Copyright
Recording of copyrighted material for other than personal use is
illegal without permission of the copyright holder.
3. Deck Location
2. Retain Instructions — The safety and operating instructions
should be retained for future reference.
3. Heed Warnings — All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions — All operating and use instructions should
be followed.
• Do not use or leave in direct sunlight or in other places
subject to high temperature and humidity. The unit should
also not be left in potentially hot places such as near heating
appliances. Excessive heat and moisture can lead to internal
damage and serious malfunctions. (This also applies to
cassette tapes.) The recommended ambient temperature range
is 5°C to 35°C.
5. Water and Moisture — The appliance should not be used near
water — for example, near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool, and the
like.
6. Carts and Stands — The appliance should be used only with a
cart or stand that is recommended by the manufacturer.
6A. An appliance and cart combination should be moved with care. Quick
stops, excessive force, and uneven surface may cause the appliance
and cart combination to overturn.
• Avoid damp and dusty places and locations prone to vibra-
tions.
PORTABLE CART WARNING
• Be extremely careful with the recording/playback heads.
Clean and demagnetize them regularly, but under no circum-
stances should magnets or other metals be used anywhere
near the heads.
• This unit is extremely sensitive to magnetic fields, so do not
use near large speakers or other devices which generate
magnetic fields.
S3125A
• Hum may even be included by magnetic flux leakage from
the power transformer in certain amplifiers. Therefore, this
unit should also be kept clear of the amplifier.
• Do not remove the cabinet case. If any of the internal parts
are handled, there is a considerable danger of electric shock.
4. Cassettes to Avoid:
• Cassettes with poorly formed cases that rattle during rewind
and fast forward.
• Low cost cassettes with no guide roller or pressure pad spring
should never be used for stereo.
• C-120 cassettes — because the tape and the coating are
extremely thin, distortion levels are high. Also, even a slight
stretching of the tape will make it susceptible to being caught
up in the pinch roller and capstan.
• Endless tapes, if used for a long period of time, can overheat.
5. Power
7. Wall or Ceiling Mounting —
to a wall or ceiling only as recommended by the manufacturer.
The appliance should be mounted
8. Ventilation – The appliance should be situated so that its location
or position does not interfere with its proper ventilation. For example,
the appliance should not be situated on a bed, sofa, rug, or similar
surface that may block the ventilation openings; or if placed in a
built-in installation, such as a book case or cabinet that may impede
the flow of air through the ventilation openings, there should be free
space of at least 20 cm (8 in.) and open up behind the appliance.
9. Heat — The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
10. Power Sources — The appliance should be connected to a power
supply only of the type described in the operating instructions or as
marked on the appliance.
11. Polarization — The polarization of the plug is a safety feature. The
polarized plug will only fit the outlet one way. If the plug does not fit
fully into the outlet, try reversing it. If there is still trouble inserting
it, the user should seek the services of a qualified electrician. Under
no circumstances should the user attempt to defeat the polarization of
the plug.
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST
TIME, READ THE FOLLOWING SECTION CARE-
FULLY.
12. Power-Cord Protection — Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items placed
upon or against them, especially near plug, convenience receptacles,
and the point where they exit from the appliance.
•
Some models are designed for use only with the power
supply voltage of the region where they are sold.
European and Australian models: AC 230 V, 50 Hz
13. Cleaning — The appliance should be cleaned only as recom-
U.S.A. and Canadian models:
AC120 V, 60 Hz
mended by the manufacturer.
Worldwide model:
AC 120/220-230 V
14. Nonuse Periods — The power cord of the appliance should be
switchable, 50/60 Hz
unplugged from the outlet when left unused for a long period of time.
• Voltage Selector (Rear Panel)
15. Object and Liquid Entry — Care should be taken so that objects
do not fall and liquids are not spilled into the enclosure through
openings.
The worldwide model is equipped with a voltage selector
to conform with local power supplies. Be sure to set this
switch to match the voltage of the power supply in your
area before plugging in the unit. (See “Setting the Voltage
Selector [Worldwide Model Only]” on page 5.) Models
without a voltage selector can only be used in areas where
the power supply voltage is the same as that of the unit.
16. Damage Requiring Service —
The appliance should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance;
or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a
marked change in performance; or
Dolby noise reduction and HX Pro headroom extension
manufactured under license from Dolby Laboratories Licens-
ing Corporation. HX Pro originated by Bang & Olufsen.
“Dolby,” the double-D symbol and “HX PRO” are trademarks
of Dolby Laboratories Licensing Corporation.
E. The appliance has been dropped, or the enclosure damaged.
17. Servicing — The user should not attempt to service the appliance
beyond that described in the operating instructions. All other
servicing should be referred to qualified service personnel.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Positions and Names
If there is a protective film on the surface of
the display, which makes it difficult to read
the display, remove it.
For more information about a button or
control, turn to the page number listed in
square brackets ([ ]).
5. DECK A/B
6. RESET
4
7. EJECT
8
3. EJECT
2
1
9
Front panel
EJECT
DECK A/B RESET
EJECT
DECK
A
DECK
B
1. Deck A cassette holder
2. Deck A operation buttons
DUBB. STOP
2
MOTER COMPUTER CONTROL
AUTO REVERSE
2
MOTER COMPUTER CONTROL
AUTO REVERSE
/
/
a
e
s
: Reverse play button [6]
: Stop button [6,9]
: Forward play button
[6,9,10,11]
POWER
PHONES
REVERSE MODE
DUBBING
REC BALANCE REC LEVEL
NORMAL
HIGH
DOLBY NR
L
R
MIN
MAX
ON
OFF
STEREO CASSETTE TAPE DECK TA-RW544
t : Rec/pause button [9,10,11]
(TA-RW544 only)
d: Rewind button [7]
f: Fast forward button [7]
3. Deck A EJECT button [6,8]
4. Display
16. POWER
15. PHONES
10. REC LEVEL
11. REC BALANCE
(TA-RW544 only)
12. DUBBING
14. DOLBY NR
13. REVERSE MODE
5. DECK A/B counter button
[9,10,11]
(TA-RW544)
6. Counter RESET button [9,10,11]
7. Deck B EJECT button [6,8]
8. Deck B operation buttons
DECK-A
PLAY
REC
PAUSE
DOLBY NR
DECK-B
PLAY
REC
PAUSE
a
: Reverse play button [6]
B
C
HI-SPEED DUBBING
OFF
e DUBB.STOP : Stop button
L
dB
R
A
B
(Dubbing stop) [7,9,12]
-
-20
-10
-6
-3
0
+3
+6
s
: Forward play button
[6,9,10]
t : Rec/pause button [9,10,12]
; : Auto space button [13]
d: Rewind button [7]
f: Fast forward button [7]
9. Deck B cassette holder
10. REC LEVEL control knob
[9,10,11]
(TA-RW344)
11. REC BALANCE control knob
[9,10,11] (TA-RW544 only)
12. DUBBING buttons (NORMAL/
HIGH) [12]
13. REVERSE MODE button
[6,8,12,15]
DECK-A
PLAY
DOLBY NR
DECK-B
PLAY
B
C
HI-SPEED DUBBING
OFF
REC
PAUSE
L
A
B
-
-20
-10
-6
-3
0
+3
+6
dB
R
14. DOLBY NR button [6,8]
15. PHONES (Headphones) jack [7]
16. POWER button [5]
Display
5
1. LINE IN
2. LINE OUT
a Deck A operation and direction
indicators
b Reverse mode indicator
c Dubbing indicators
d Dolby NR indicators
e Deck B operation and direction
indicators
LINE IN LINE OUT
(REC) (PLAY)
VOLTAGE SELECTOR
REMOTE
CONTROL
L
L
220V-230V
120V
R
R
f Electric counter
g Peak level indicator
4.
REMOTE CONTROL
3. VOLTAGE SELECTOR
Rear panel
1. Line in jacks [5]
2. Line out jacks [5]
3. Voltage selector [5] (Worldwide
model only)
4. Remote control jacks [14]
4
5. AC power cord [5]
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Voltage Selector
(Worldwide Model Only)
Models without a voltage selector can only be used in areas where the power supply is the same as that of the cassette deck.
1. Determine the proper voltage for your
area: 220-230 V or 120 V.
2. If the preset voltage does not conform
to your area, insert a screwdriver into
the groove in the switch. Slide the
switch all the way to the right (120 V)
or to the left (220-230 V), whichever is
appropriate.
C
A
U
T
I
O
N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
VOLTAGE SELECTOR
220V-230V
120V
220V-230V
120V
System Connections
• Do not plug in the AC power cord until all other connections have been made.
• On each pair of input or output jacks, the lower jack (marked R) corresponds to the right channel, and the upper jack (marked L) to
the left channel. Refer to the amplifier’s instruction manual for further information on connections.
Connecting to an amplifier
Connect the tape deck LINE IN jacks to the
TAPE REC jacks on the rear panel of the
amplifier and the tape deck LINE OUT
jacks to the amplifier TAPE PLAY jacks.
Refer to the amplifier’s instruction manual
C
A
U
T
I
O
N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
220V-230V
120V
for further information on connections.
•
-
•
-
•
TAPE
(REC)
(PLAY)
L
R
L
R
LINE IN LINE OUT
(REC) (PLAY)
L
R
Power Connections
Switching power on
1. Plug the AC power cord into a
wall outlet.
2. Press the POWER button.
The display will light.
1
To a wall outlet
2
POWER
OFF
ON
5
Download from Www.Somanuals.com. All Manuals Search And Download.
To Play a Tape
• Check once again that all connections have been completed exactly as indicated in the connections diagram and then plug in the AC
power cord.
• After turning the power on, the display illuminates and the g PAUSE indicator flashes (about 5 seconds). While the indicator is
flashing, no operation can be performed.
• This deck holds two cassettes at once. Both Deck A and Deck B are capable of auto-reverse playback.
• Tapes can be played back using either Deck A or Deck B. Follow the procedure on Deck A or B. (Deck A is pictured.)
2
1
5
d,f(DECK A) 3
4
d,f(DECK B)
Listening to a tape
1. Press the EJECT button to open
the cassette holder.
2. Insert a cassette.
• The side of the cassette with the
exposed tape should be facing down-
ward.
3. Set the Dolby NR by pressing
the DOLBY NR button repeat-
edly until the proper Dolby NR
indicator (OFF, B or C) turns on.
• Select the same noise reduction system
that was used when the cassette was
recorded. For instance, tapes recorded
using Dolby B NR should be played
back with Dolby B NR.
1
2
EJECT
4. Set the Reverse Mode by press-
ing the REVERSE MODE button
repeatedly until the desired
mode is displayed.
DOLBY NR
OFF
DOLBY NR
3
4
5
B
C
( v ) one side: Only one side of the
tape is played back.
( b ) repeat: Both sides of the tape are
played back repeatedly eight
times or until the e button is
pressed.
REVERSE MODE
5. Start playback.
• Press the a or s button depending
on which side of the cassette you wish
to listen to.
s : Playback starts from the front
side.
a : Playback starts from the reverse
side.
• The auto-stop mechanism will auto-
matically stop the tape (depending on
the tape transport mode) if a tape is
played through to the end.
Stopping playback
Press the e button.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Recheck the tape direction settings (shown
by the Deck A and Deck B direction
indicators) before pressing the d or
f button.
A
A
f
The following explanation assumes that the
tape direction is forward ( s ).
Fast forward and rewind
Make sure the tape is stopped before using
the fast forward or rewind function.
To fast forward the tape, press the f
button.
A
A
d
To rewind the tape, press the d button.
• To stop either fast forward or rewind,
press the e button.
Listening with the headphones
Plug the headphones to the PHONES jack.
EJECT
DECK A/B
RE
Automatic tape selection system
This deck detects the type of cassette in the
cassette holder and automatically sets the
bias and equalization to the correct settings.
Tape selection is performed by detecting
the presence or absence of identification
pits on the back of the cassette shell.
Cassettes manufactured before this
DU
/
/
POWER
PHONES
REVERSE MODE
DOLBY NR
DUBBING
NORMAL HIGH
ON
OFF
identification system was adopted and
bargain cassettes that do not incorporate
these pits cannot be used with this deck.
Useful Functions Available during Play-
back
(TA-RW544 Only)
Skipping to a song
A
Make sure the tape is playing before using
this function.
To skip ahead to the next song,
press the f button.
It is possible to skip up to 15 songs at one
time. The number of songs skipped is
indicated by the display (P1, P2 ..... P15).
f
4
5
6
f
f
f
Skipping to the beginning of the
current song or a preceding song
DECK-B
Make sure the tape is playing before using
this function.
To skip back to the beginning of the
song being played or preceding
song, press the d button.
The number of songs skipped is indicated
by the display (–P1, –P2 ..... –P15).
A
Note:
The Skip function operates by detecting the
blank space between songs. Therefore, it
may not operate properly under circum-
stances such as the following:
1) The blank space is too short.
2) The song is interrupted by narration,
etc.
d
1
2
3
4
d
d
d
d
DECK-B
3) The music level changes, such as a
quiet section immediately followed by
a loud section.
4) There is excessive noise between songs.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
With TA-RW544, both Deck A and Deck B can be used for recording. Three recording methods are possible.
(A) Recording on a single cassette using Deck A or Deck B
(B) Recording the same program simultaneously on cassettes in both Deck A and Deck B
(C) Recording on two cassettes consecutively using first Deck A then Deck B
• With TA-RW344, only Deck B is available for recording.
• Check to see if one or both of the cassette’s erasure prevention tabs have been removed.
• Confirm that the cassette deck is properly connected to the amplifier.
• Illustrations enclosed in solid boxes
indicate source component operations.
1
1
3
4
Preparing for recording
Confirm that the amplifier is set up
correctly for recording. (Refer to the
amplifier’s instruction manual for details.)
1. Insert the cassettes.
Make sure the side to be recorded is
facing outward.
• Recording is not possible on the tape
leaders (the transparent sections you
see at both ends of the tape).
2. Prepare the source component to
be used for the recording.
• Tune in the desired station on the tuner.
• Load a CD (or LP) into the CD player
(or turntable).
1
2
• Load a cassette into the tape player
(analog or DAT).
3. Set the Dolby NR by pressing
the DOLBY NR button repeat-
edly until the desired Dolby NR
indicator (OFF, B or C) turns on.
4. Set the Reverse Mode by press-
ing the REVERSE MODE button
repeatedly until the desired
mode is displayed.
3
DOLBY NR
OFF
DOLBY NR
( v ) one side: Only one side of the
tape is recorded.
B
C
( b ) repeat: Both sides of the tape are
recorded.
• When recording from a source compo-
nent to Deck A and Deck B consecu-
tively, select the “ b ” mode.
4
REVERSE MODE
Note:
This deck will not begin recording if you
press the t and s or a button at the
same time. To begin recording, first press
the t button to put the deck into the rec/
pause mode, then press either the s or a
button as appropriate.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
(A) Recording on a single cassette using Deck A or Deck B
2
7
4
5
The following explanation assumes that
Deck B is being used.
eDUBB. STOP
Procedure for recording
1. Prepare for recording.
(See page 8.)
2
DECK-B
DECK A/B RESET
Note:
With TA-RW544, when recording to
Deck A only, do not insert a cassette in
Deck B. In the “ b ” mode, recording
in Deck B may start consecutively.
2. Press the DECK A/B button to
select the appropriate Deck A or
B, and press the RESET button
to return the tape counter to
[0000].
3. Begin playing the source compo-
nent.
4. Press the t button.
5. While observing the peak level
indicators, adjust the recording
level and balance.
B
3
4
s
REC
PAUSE
DECK-B
t
B
• Use the REC LEVEL knob to adjust the
recording level.
• With TA-RW544, adjust the REC
BALANCE knob so that the left and
right channels have approximately the
same levels. This knob is normally at
the center position.
5
REC BALANCE REC LEVEL
DECK-A
DOLBY NR
REC
PAUSE
DECK-B
C
• When using metal cassettes, the REC
LEVEL knob should be adjusted so that
+3 dB indicators light periodically.
When using other kinds of tapes, the 0
dB indicator should light periodically.
(See “Making Good Sound Record-
ings” on page 13.)
L
dB
R
-
-20
-10
-6
-3
0
+3
+6
B
L
R
MIN
MAX
(TA-RW544 only)
6. Put the source component into
recording standby status.
• Temporarily stop CD (or LP) play.
• Rewind the tape to the portion you wish
to start playback.
6
e
7. Press the s button on this unit
and begin playing the source
component.
7
s
You can also use the CD Synchro
Recording function if this unit is
properly connected to an ONKYO
CD player bearing the z symbol.
Stopping recording
(See page 14.)
Press the e DUBB.STOP button.
e DUBB. STOP
t
Interrupting recording briefly
Press the t button.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
(B) Recording the same program simultaneously on cassettes in both Deck A and Deck B (TA-RW544
only)
2
7
4
5
Procedure for recording
DECK A/B RESET
DECK A/B RESET
1. Prepare for recording.
(See page 8.)
2. Press the RESET button to return
the tape counter for both Deck A
and Deck B to [0000].
2
A
B
• To change the active deck, press the
DECK A/B button.
3. Begin playing the source compo-
nent.
4. Press the Deck A and Deck B
3
4
s
t buttons.
5. While observing the peak level
indicators, adjust the recording
level and balance.
• Use the REC LEVEL knob to adjust the
recording level.
t
DECK-A
REC
PAUSE
DOLBY NR
+6
REC
PAUSE
DECK-B
C
L
dB
R
t
-
-20
-10
-6
-3
0
+3
B
• Adjust the REC BALANCE knob so
that the left and right channels have
approximately the same levels. This
knob is normally at the center position.
6. Put the source component into
recording standby status.
5
7. Press the Deck A or Deck B
button and begin playing the
source component.
s
REC BALANCE REC LEVEL
DECK-A
REC
PAUSE
DOLBY NR
+6
REC
PAUSE
DECK-B
C
L
dB
R
You can also use the CD Synchro
Recording function if this unit is
properly connected to an ONKYO
-
-20
-10
-6
-3
0
+3
B
L
R
MIN
MAX
CD player bearing the z symbol.
(See page 14.)
Notes:
6
7
• The following buttons and knob affect
both Deck A and Deck B.
— The REVERSE MODE button
— The DOLBY NR button
— The REC LEVEL knob and REC
BALANCE knob
• The auto space function operates both
Deck A and Deck B at the same time.
And, pressing the a , s or t
button on either Deck A or Deck B
affects both Deck A and Deck B.
e
s
Stopping recording
e
DUBB. STOP
e
To stop recording on Deck A or Deck B
only, press the appropriate deck e button.
or
10
Download from Www.Somanuals.com. All Manuals Search And Download.
(C) Recording on two cassettes consecutively using first Deck A then Deck B (TA-RW544 only)
8
3
2
5
6
Procedure for recording
1. Prepare for recording.
(See page 8.)
2
3
e
DUBB. STOP
s
DECK-B
Note:
Be sure to set the reverse mode to
“ b ” mode.
2. Check that the Deck B direction
indicator is forward ( s ).
• To change the setting of the direction
indicator, press the s button followed
by the e DUBB.STOP button.
3. Press the RESET button to return
the tape counter for both Deck A
and Deck B to [0000].
DECK A/B RESET
DECK A/B RESET
A
B
• To change the active deck, press the
DECK A/B button.
4. Begin playing the source compo-
nent.
5. Press the Deck A t button.
6. While observing the peak level
indicators, adjust the recording
level and balance.
4
5
s
• Use the REC LEVEL knob to adjust the
recording level.
t
DECK-A
REC
PAUSE
• Adjust the REC BALANCE knob so
that the left and right channels have
approximately the same levels. This
knob is normally at the center position.
7. Put the source component into
recording standby status.
8. Press the Deck A s button and
begin playing the source compo-
nent.
You can also use the CD Synchro
Recording function if this unit is
properly connected to an ONKYO
CD player bearing the z symbol.
(See page 14.)
6
REC BALANCE REC LEVEL
DECK-A
REC
PAUSE
DOLBY NR
+6
DECK-B
C
L
dB
R
-
-20
-10
-6
-3
0
+3
B
L
R
MIN
MAX
Note:
7
e
If one of the erasure prevention tabs of the
cassettes inserted into Deck A and Deck B
has been removed, recording will stop on
that side. For example, the broken tab on
the reverse side of the cassette inserted into
Deck A will cease reverse side recording on
Deck A and both sides recording on Deck
B.
8
s
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Tape Dubbing
• The recording level will be fairly close to that of the tape in Deck A.
• The Dolby NR System of Deck A is automatically used to record the tape in Deck B. If you wish to monitor the signal from a Dolby
NR encoded tape during normal-speed dubbing, be sure to set the Dolby NR to match the type of Dolby NR with which the cassette
was recorded.
• During high-speed dubbing, decrease the sound level from the amplifier (or receiver) using the volume control and unplug the
headphones from the headphone jack.
1
2
1
4
Tape dubbing
1. Insert the prerecorded cassette
into Deck A , and insert the
cassette to be recorded into Deck
B.
1
2. Set the Reverse Mode by press-
ing the REVERSE MODE button
repeatedly until the desired
mode is displayed.
( v ) one side: Only one side of the
tape is copied.
( b ) repeat: Both sides of the tape are
copied.
2
3
4
REVERSE MODE
3. Check the Deck A and Deck B
direction indicators to ensure
that the tape transport will start
in the desired direction.
• To dub an entire tape, be sure to select
the forward ( s ) direction on both
Decks.
DECK-A
PLAY
DECK-B
PLAY
To change the setting of the direction
indicator, press the a or s button,
then the e button
DUBBING
4. Begin dubbing by pressing the
NORMAL or HIGH button.
[NORMAL] : Normal-speed dubbing
will begin.
HIGH
HI-SPEED DUBBING
DUBBING
NORMAL
HIGH
NORMAL
[HIGH] : High-speed dubbing about
half the time normally required
will begin.
DUBB. STOP
Stopping dubbing
Press the Deck B e DUBB.STOP
button.
Briefly interrupting dubbing
t
Press the t button. (Deck B)
In this case, you can change the cassette in
Deck A or search the desired portion by
using the buttons for Deck A. To resume
dubbing, press the NORMAL or HIGH
button again.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Useful Recording Functions
Inserting blank spaces between
songs when editing tapes
1. Press the t button and the
or s button to begin recording.
2. Press ; button at any point
a
during recording where you want
to enter a blank space about five
seconds long.
a , s (Deck A)
• The
indicator flashs on and off.
PLAY
a , s (Deck B)
• After the blank space has been inserted,
the tape stops automatically and the
deck returns to the rec/pause mode.
3. To continue recording, press the
a or s button.
• The ; button works in both the record
and rec/pause modes.
To insert a blank space of less
than five seconds between songs
Press the t button to return to the rec/
pause mode or press the a or s button
before a five-second period has elapsed.
t
;
To insert a blank space of more
than five seconds between songs
Hold the ; button down for as long as you
want the blank space to be. The deck will
return to the rec/pause mode immediately
when the button is released.
Pressing the ; button during
dubbing
;
Pressing the ; button during dubbing
causes Deck A to stop while a blank space
is inserted on the tape in Deck B. Then
Deck B reverts to the dubbing pause mode.
To continue dubbing, press the NORMAL
or HIGH button.
Making Good Sound Recordings
Dolby Noise Reduction System
Setting the Proper Recording Level
The recording level has an important effect on the sound quality a
tape will have when it is played back. A recording level that is
too high will cause distortion while one which is too low will
lower the signal-to-noise ratio resulting in a tape with excessive
“hiss noise.” It is particularly important to set the recording level
correctly with cassette tapes since they have a much thinner
magnetic coating than open reel tapes. The thin coating gives the
tape a comparatively low saturation level which can easily be
surpassed if the recording level is set too high.
The optimal recording level varies depending on the type of the
tape being used. With this tapedeck, adjust the REC LEVEL knob
so the PEAK LEVEL indicator occasionally hits the “+6dB” line
with “Metal” tapes and “+4dB” line with “Normal” or “High”
position tapes, respectively. It should be noted that the peak level
may change from one track to another on some recording sources.
The recording level indicators feature a peak-hold function for the
indicators from –6 dB through +6 dB. This can come in handy
when setting the recording level.
Dolby B NR is the system used in most cassette tape decks to
reduce the background noise that is inherent in all cassette tapes.
This deck also features Dolby C NR, an even more effective
noise reduction system, developed by Dolby Laboratories in
response to the demand for even better sound from cassette tapes.
The Dolby HX Pro System
Tape sensitivity is constantly changing as recordings are made
due to the biasing effect of high frequency audio signals. Dolby
HX Pro is a system that compensates for these undesirable
fluctuations during recording. It does not operate during play-
back, so cassettes recorded with Dolby HX Pro can be played
back on decks not equipped with the system.
Note:
Dolby HX Pro operates independently of Dolby B and C NR, and
only during recording.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting ONKYO Components for z
Operation
If this unit is properly connected to another ONKYO component bearing the z symbol, you will be able to control it using the other
component’s remote control.
For remote control operation
The upper and lower remote control jacks
Tuner
have the same function.
For remote control operation, connect this
jack to any ONKYO amplifier, receiver or
CD player that are equipped with a z
remote control jack using the remote
control cable.
CD player
Note:
1
2
3
4
5
6
7
8
9
0
+10
6 DISC
Do not attempt to connect the z remote
control jack to any equipment other than an
ONKYO component that are equipped with
a z remote control jack. Doing so could
cause the unit to malfunction.
Main amplifier
Pre amplifier
The function listed below can be accom-
plished using the remote control of the
master unit.
s a
d
f
e
: Play
: Rewind
: Fast forward
: Stop
t
: Rec/Pause
TA-RW544
TA-RW344
CD synchro recording system
Once connections are made, as shown left,
this function becomes enabled. It automati-
cally starts recording on the cassette deck
when the s button of the CD player is
pressed. (See below.)
CD Synchro Recording System
Once the TA-RW544/344 is connected to a CD player bearing the z symbol (see above), pressing the s button of the CD player will
cause recording to begin automatically on the TA-RW544/344. Three recording methods are possible. (See pages 8 - 11.)
1. Prepare for recording.
(See pages 8 - 11.)
2
2. Start the CD player.
Recording will begin simultaneously.
s
Note:
Even if the CD player is stopped during
recording, the cassette deck will continue
recording. In this case, make sure to press
the e button on the cassette deck.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Reverse Mode Function
• Recheck the tape travel direction settings (shown by the Deck A and Deck B direction indicators) before beginning playback or
recording.
• The following explanation assumes that cassette side A is facing outward.
• There is a silent gap about ten seconds long when the direction of tape travel switches from forward to reverse or from reverse to
forward when the end of a tape side is reached.
Reverse mode
Direction
Playback / Recording sequence
Explanation
Press the s button. Playback will begin and
end on side A (front).
s
A
B
Press the a button. Playback will begin and
end on side B (rear).
a
s
Press the s button. Playback will begin
from side A and continue to side B. When the
end of side B is reached, the playback begin
again from side A . This sequence will repeat
eight times.
A → B → A → B ⋅⋅⋅⋅ → A →
B
Press the a button. Playback will begin
from side B and continue to side A. When the
end of side A is reached, the playback begin
again from side B. This sequence will repeat
eight times.
Deck A or Deck B
a
B → A → B → A ⋅⋅⋅⋅ → B →
A
A → B → A → B ⋅⋅⋅⋅ → A →
If there are tapes in both Deck A and Deck B,
playback will begin from side A of the tape in
Deck A. When the end of side B is reached,
Deck B will begin playback. This sequence
will repeat four times.
s
a
Deck A
Deck B
Deck B
B
One cycle
B → A → B → A ⋅⋅⋅⋅ → B →
Deck B Deck A
Deck A and Deck B
Deck A Deck B
Deck A
One cycle
A
Press the t button then the s button.
Recording will begin from and end on side A
(front).
s
a
A
B
Press the t button then the a button.
Recording will begin and end on side B
(rear).
Press the t button then the s button.
Recording will begin from side A and
continue to side B. When the end of side B is
reached, recording will stop automatically.
s
a
A → B
If you begin recording in the reverse
direction, recording will begin from side B of
the tape. When the end of side B is reached,
recording will stop automatically.
B
Continuous recording
Before performing continuous recording, set
the direction of the tape in Deck B.
s
A → B → A → B
Deck A
Press the Deck A t button then the s (or
a ) button. Recording will begin from side
A (B) of the tape in Deck A. As soon as the
recording on side B of the tape in Deck A is
complete, recording on Deck B will begin.
Deck A
Deck B
Deck A and Deck B
(TA-RW544 only)
a
B → A → B
Deck A
Deck A
Deck B
* You can simultaneously record on tapes in Deck A and Deck B except during continuous recording.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling Cassette Tapes
Examine cassette tapes carefully before using them with the TA-RW411.
Erasure prevention
A
B
Cassette tapes are constructed with erasure
prevention tabs to prevent accidental
erasure of the tape.
A
1
If you wish to protect a recording from
accidental erasure, break off the tab(s)
on the appropriate side(s). It will no
longer be possible to use the recording
button with such a cassette.
1.
2.
High position
detection hole
2
If at some later date you wish to record
the cassette, simply cover the hole(s)
with small pieces of cellophane tape.
• Be sure not to cover the holes for
detecting high-position tapes.
Loose tape
Loose tape can cause tangling around the
pinch roller and capstan and jam the
mechanism.
Remove any tape slack with a pencil or
similar device as shown in the diagram.
A
Tapes not recommended
1. C-120 tapes
C-120 tape is thin and therefore easily
broken. There is a possibility that tape
could get caught on the pinch roller or
capstan.
2. Endless tapes
Do not use endless tapes.
Tape storage
• Do not touch the tape surface.
• Do not put thick paper or cardboard
labels in the cassette holder.
• Do not put tapes near magnetic sources
(speakers, amplifiers, TVs, etc.) Your
important recording might be erased or
damaged.
A
A
No!
No!
• Do not expose cassettes to direct
sunlight.
Recommended tapes
Normal position High position Metal position
Maxell UDI
Maxell UDII
Maxell XS
No!
No!
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cassette Deck
Maintenance
REC/PB head
Erase head
Capstans
Pinch rollers
This deck requires no lubrication.
Head, Pinch Roller and Capstan Cleaning
Playback sound quality can be greatly diminished if magnetic
particles are allowed to accumulate on the recording/playback
head or playback head. Be sure to clean the head periodically,
normally 2 - 3 times a month, to maintain your deck’s original
performance. Dirty heads may cause:
• Poor sound quality (lose of high frequency response)
• Decreased volume
• Skipping
• Incomplete erasure of previous recordings
If the pinch rollers and capstan are dirty, the tape may become
tangled and damaged by wrapping around the pinch roller and
capstan.
To prevent these problems, clean the heads, pinch rollers and
capstans with a cotton swab dipped in cleaning fluid.
Demagnetizing
Residual magnetism builds up in the heads after the cassette deck
has been used for an extended period of time. This buildup
introduces noise and static into tapes and impairs high frequency
response. To prevent this, demagnetize the heads with any
commercially available head eraser once every 50 hours of use.
Refer to the instruction manual of the head eraser for detailed
instructions.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
TA-RW544
TA-RW344
Track Format:
Erasure System:
Tape Speed:
4-track, 2-channels
AC erase
4.8 cm/sec. (1-7/8 i.p.s.)
9.6 cm/sec. (3-3/4 i.p.s.) (high speed
dubbing)
Track Format:
Erasure System:
Tape Speed:
4-track, 2-channels
AC erase
4.8 cm/sec. (1-7/8 i.p.s.)
9.6 cm/sec. (3-3/4 i.p.s.) (high-speed
dubbing)
Wow and Flutter:
0.07 % (WRMS)
Wow and Flutter:
0.07 % (WRMS)
Frequency Response:
20 — 15,000 Hz (Normal)
(30 — 14,000 Hz ± 3 dB)
20 — 16,000 Hz (High)
(30 — 15,000 Hz ± 3 dB)
20 — 17,000 Hz (Metal)
(30 — 16,000 Hz ± 3 dB)
Dolby NR off: 58 dB (metal position
tape)
Frequency Response:
20 — 15,000 Hz (Normal)
(30 — 14,000 Hz ± 3 dB)
20 — 16,000 Hz (High)
(30 — 15,000 Hz ± 3 dB)
20 — 17,000 Hz (Metal)
(30 — 16,000 Hz ± 3 dB)
Dolby NR off: 58 dB (metal position
tape)
S/N Ratio:
S/N Ratio:
A noise reduction of 10 dB above
5 kHz and 5 dB at 1 kHz is possible
with Dolby B NR.
A noise reduction of 10 dB above
5 kHz and 5 dB at 1 kHz is possible
with Dolby B NR.
A noise reduction of 20 dB at 5 kHz
is possible with Dolby C NR.
Line IN: 2
Input sensitivity: 80 mV
Input impedance: 40 kohms
Line OUT: 2
A noise reduction of 20 dB at 5 kHz
is possible with Dolby C NR.
Line IN: 2
Input sensitivity: 80 mV
Input impedance: 50 kohms
Line OUT: 2
Input Jacks:
Outputs:
Input Jacks:
Outputs:
Standard output level: 500 mV
(0 dB)
Standard output level: 500 mV
(0 dB)
Optimum load impedance: over
50 kohm
Optimum load impedance: over
50 kohms
Headphone jack:
1
Headphone jack:
1
Optimum load impedance:
8 to 200 ohms
Optimum load impedance:
8 to 200 ohms
Motors:
Heads:
DC servo motor × 2, DC motor × 2
REC/PB: 2
Motors:
Heads:
DC servo motor × 2, DC motor × 2
REC/PB: 1
ERASE: 2
PB: 1
Power Supply:
European and Australian models:
AC 230V, 50 Hz
U.S.A. and Canadian models:
AC 120V, 60 Hz
ERASE: 1
European and Australian models:
AC 230V, 50 Hz
U.S.A. and Canadian models:
AC 120V, 60 Hz
Power Supply:
Worldwide model:
AC 120V and AC 220-230V,
Switchable 50/60 Hz
31 watts
435(W) × 121(H) × 305(D) mm
(17-1/8" × 4-3/4" × 12")
5.9 kg. (13.0 lbs.)
Worldwide model:
AC 120V and AC 220-230V,
Switchable 50/60 Hz
29 watts
435(W) × 121(H) × 305(D) mm
(17-1/8" × 4-3/4" × 12")
5.9 kg. (13.0 lbs.)
Power Consumption:
Dimensions:
Power Consumption:
Dimensions:
Weight:
Weight:
Specifications and external appearance are subject to change
without notice because of product improvements.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
The following guide lists problems which do not require professional servicing. If, however, the problem cannot be remedied using this
guide, contact an ONKYO authorized service center for assistance.
• No power.
Cause: Power cord plug is loose
Remedy: Insert plug properly into outlet.
• Tape squeal and skipping.
Cause: Dirty heads, pinch rollers or capstan shafts.
Remedy: Clean (see page 17).
Cause: Cassette shell is binding tape or tape is stretched.
Remedy: Change cassette or try correcting with fast
forward and rewind.
• Playback but no sound.
Cause: Incorrect connection.
Remedy: Check and connect correctly according to page
5.
Cause: Stereo amplifier input selector switch is set to
incorrect position.
• Excessive hum during playback.
Cause: Connecting cables not inserted firmly.
Remedy: Insert plugs firmly.
Remedy: Change switch position.
Cause: External flux leakage from nearby amplifier or TV
set.
• Tape does not move.
Remedy: Move deck away from hum source.
Cause: Slack tape wound around pinch roller.
Remedy: Take up slack with a pencil (see page 16).
• High frequencies too strong.
Cause: Dolby NR encoded tape played back with NR off.
Remedy: Select the same noise reduction (Dolby NR B
C) used when the cassette was recorded.
Cause: Incorrect equalization.
• t button does not engage.
Cause: No tape in cassette holder.
Remedy: Insert cassette tape.
or
Cause: Erasure prevention tab(s) removed.
Remedy: Change cassette or cover tab hole with
cellophane tape.
Remedy: Confirm that cassette has tape type detection
holes.
• No high frequency sounds.
Cause: Tape not encoded with Dolby NR played back
with Dolby B or C NR on.
Remedy: Select the appropriate NR mode using the
DOLBY NR button (OFF).
• Hoarse sound, balance unstable.
Cause: Playback head dirty.
Remedy: Clean head (see page 17).
Cause: Tape is stretched.
Remedy: Replace cassette.
Cause: Heads have become dirty.
Remedy: Clean (see page 17).
• Excessive noise and tape hiss.
Cause: Head has become magnetized.
Remedy: Demagnetize (see page 17).
Cause: Tape with high noise level.
Remedy: Replace cassette.
• The skip function does not operate properly (TA-
RW544 only).
Cause: The silent sections between songs are too short or
noisy.
Remedy: Use a cassette with sufficient silent sections of
sufficient length between songs.
• Distorted sound.
Cause: Distortion in tape.
Remedy: Tape is probably bad but confirm by listening
• Deck does not operate properly.
to
another.
Cause: Tape transport control microcomputer has been
exposed to interference from power supply or static
electricity.
• Recordings are distorted.
Cause: Recording was done at too high a level.
Remedy: Readjust REC LEVEL knob according to the
directions on page 9.
Remedy: Press the POWER button to turn off the
power.
Wait approximately 10 seconds
again.
and turn it on
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Sales Planning & Promotion Dept.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572, JAPAN
Tel: 0720-31-8111 Fax: 0720-33-5222
ONKYO U.S.A. CORPORATION
200 Williams Drive, Ramsey, N.J. 07446, U.S.A.
Tel: 201-825-7950 Fax: 201-825-8150 E-mail: onkyo@onkyousa. com
ONKYO EUROPE ELECTRONICS GmbH
Industriestrasse 18-20, 82110 Germering, GERMANY
Tel: 089 84 93 20 Fax: 089 84 93 226
ONKYO FRANCE
Immeuble Le Diamant, Domaine Technologique de Saclay, 4 Rue René Razel,
91892 SACLAY, FRANCE Tel: (1) 69 33 14 00 Fax: (1) 69 41 35 84
HOMEPAGE
SN29342382Y
E
Download from Www.Somanuals.com. All Manuals Search And Download.
|