Contents
AM/FM Tuner
Introduction.................................... 2
T-4355
Instruction Manual
Connections................................. 10
Enjoying Audio Sources.............. 14
Troubleshooting........................... 20
Specifications .............................. 21
Thank you for purchasing an Onkyo AM/FM Tuner.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new Tuner.
Please retain this manual for future reference.
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal with-
out the permission of the copyright holder.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild deter-
gent and water. Dry the unit immediately afterwards
with a clean cloth. Don’t use abrasive cloths, thin-
ners, alcohol, or other chemical solvents, because
they may damage the finish or remove the panel let-
tering.
Blue:
Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the
same ampere rating as that indicated on the plug. Check
for the ASTA mark or the BSI mark on the body of the
fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable
fuse in the plug.
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
Some models have a voltage selector switch for
compatibility with power systems around the world.
Before you plug in such a model, make sure that the
voltage selector is set to the correct voltage for your
area.
5. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
For European Models
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
6. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you origi-
nally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Before Using this Unit
• Turn off the power before changing the switch set-
tings.
• On changing the switch settings, T-4355 is initialized
to its factory defaults. Radio presets and other set-
tings are deleted.
❑ 30 AM/FM Presets
❑ Automatic AM/FM Scan Tuning
❑ Selectable Character Display
❑ RDS (PS/RT) (European models only)
❑ Audiophile-Grade Capacitor
❑ Hi-Rigidity, Anti-Resonant Chassis
❑ Aluminium Front Panel
❑ RI Remote Compatible
Supplied Accessories
Make sure you have the following accessories:
Audio cable (80 cm)
Setting the AM Tuning Step Fre-
quency (Worldwide models only)
Worldwide models are equipped with a switch that con-
trols the AM band tuning steps. Please set this switch to
match the AM band tuning step frequency in your area.
cable (80 cm)
USA:
Set this switch to USA when T-4355 is used
in the 10 kHz tuning step area. North Amer-
ica is the major area using the 10 kHz step
frequency.
To use
, the T-4355 must be connected with an
cable and an audio cable.
OTHER: Set this switch to OTHER when T-4355 is
used in the 9 kHz tuning step area.
Indoor FM antenna
Setting the Voltage Selector (World-
wide models only)
Worldwide models are equipped with a voltage selector
to conform with local power supplies.Be sure to set this
switch to match the voltage of the power supply in your
area before plugging in the unit.
AM loop antenna
Determine the proper voltage for your area: 220-240 V
or 120 V.
If the preset voltage is not correct for your area, insert a
screwdriver into the groove in the switch. Slide the
switch all the way to the right (120 V) or to the left
(220-240 V), whichever is appropriate.
In catalogs and on packaging, the letter added to the end
of the product name indicates the color of the T-4355.
Specifications and operation are the same regardless of
color.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction
Important Safety Instructions.....................................................................................2
Precautions..................................................................................................................3
Features .......................................................................................................................4
Supplied Accessories.................................................................................................4
Before Using this Unit.................................................................................................4
Setting the AM Tuning Step Frequency (Worldwide models only) ........................4
Setting the Voltage Selector (Worldwide models only)..........................................4
Table of Contents........................................................................................................5
Front & Rear Panels....................................................................................................6
Front Panel............................................................................................................6
Display...................................................................................................................7
Rear Panel.............................................................................................................7
Remote Controller.......................................................................................................8
RC-627S Remote Controller (supplied with the A-9355/A-9155 Integrated
Amplifier)............................................................................................................8
Using the Remote Controller .................................................................................9
Connections
Connecting the T-4355..............................................................................................10
Connecting an amplifier.......................................................................................10
About the System Functions................................................................................11
Connecting Antennas ...............................................................................................12
Connecting the Indoor FM Antenna.....................................................................12
Connecting the AM Loop Antenna.......................................................................12
Connecting an Outdoor FM Antenna...................................................................13
Connecting an Outdoor AM Antenna...................................................................13
Enjoying Audio Sources
Turning On the T-4355 ..............................................................................................14
Listening to the Radio...............................................................................................14
Tuning into Radio Stations Manually...................................................................14
Presetting All Stations Automatically (Auto Preset).............................................15
Presetting Stations Manually...............................................................................15
Selecting Preset Stations ....................................................................................16
Naming Presets...................................................................................................17
Deleting Presets ..................................................................................................18
Displaying Information.........................................................................................18
FM Mode .............................................................................................................18
Tuner Operation with the RC-627S Remote Controller (supplied with the
A-9355/A-9155)................................................................................................18
Using RDS (European models only)....................................................................19
Others
Troubleshooting........................................................................................................20
Specifications............................................................................................................21
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Front & Rear Panels
Front Panel
ꢀ
ꢁ
ꢂ
ꢃ ꢄ
ꢅ
ꢆ
For detailed information, refer to the pages in parentheses.
ꢀ POWER switch (14)
ꢄ FM MODE button (18)
This switch is used to turn on/off the T-4355.
This button is used to set the FM mode to stereo or
mono.
ꢁ DISPLAY button (18)
This button is used to view various information on
the display.
Display
See next page.
ꢂ TUNING [ ]/[ ] buttons (14)
ꢅ BAND button (14)
These buttons are used to tune into radio stations.
They’re also used when setting the naming presets.
This button is used to select the FM or AM band.
ꢆ PRESET [ ]/[ ] buttons (14)
ꢃ MEMORY button (14)
These buttons are used to select presets. They’re
also used when setting the naming presets.
This button is used to store and delete presets.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Front & Rear Panels—Continued
Display
ꢀꢁ ꢂ ꢃ
ꢄ
ꢀ MEM (Memory) indicator
ꢃ RDS indicator (European models only)
This indicator lights up when tuned to an FM station
that supports RDS.
This indicator lights up when storing radio presets.
ꢁ AUTO indicator
ꢄ Message area
This indicator lights up when the FM mode is Auto
Stereo.
Various information is displayed here, including
preset number, tuning frequency, preset name, and
so on.
ꢂ
/FM ST indicators
These indicators show the status of the radio recep-
tion.
Rear Panel
ꢀ ꢁ
ꢂ ꢃ
ꢄ
ꢅ
For detailed information, refer to the pages in parentheses.
ꢀ ANALOG AUDIO OUTPUT (10)
These output jacks should be connected to an ana-
log audio input on the amplifier by using the sup-
plied audio cable.
ꢃ FM ANTENNA (75:) (12)
This jack is for connecting the supplied indoor FM
antenna or an outdoor FM antenna.
ꢄ FREQ. STEP switch (4)
ꢁ
REMOTE CONTROL (11)
For Worldwide models only.
These two identical
can be connected to the
Onkyo components for interactive control. To use
, the T-4355 must be connected with an
and an audio cable.
(Remote Interactive) jacks
jacks on your other
VOLTAGE SELECTOR switch (4)
For Worldwide models only.
ꢅ Power cord (14)
cable
The power cord should be connected to a suitable
power source.
ꢂ AM ANTENNA (12)
These push terminals are for connecting the sup-
plied AM loop antenna or an outdoor AM antenna.
See pages 10–13 for connection information.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
RC-627S Remote Controller (supplied with the A-9355/A-9155 Integrated Ampli-
fier)
ꢀ BAND button (14)
This button can be used to select the FM or AM
band.
If the T-4355 and A-9355/A-9155 are connected
with an
cable, pressing this button while the
entire system is on Standby will turn on only the
T-4355 and A-9355/A-9155. All other components
will remain on Standby.
ꢁ FM MODE button (18)
This button can be used to set the FM mode to ste-
reo or mono.
ꢂ
ꢃ
ꢀ
ꢁ
ꢂ PRESET [+]/[–] buttons (18)
When the input source on the A-9355/A-9155 is set
to TUNER, these buttons can be used to select pre-
sets.
ꢃ TUNING [ ]/[ ] buttons (18)
When the input source on the A-9355/A-9155 is set
to TUNER, these buttons can be used to tune into
stations.
* Any remote controller for Onkyo amplifier is avail-
able to control T-4355 in a condition of the
connec-
tion. (On some remote controllers, some buttons shown
in the figure are missing. The corresponding functions
cannot be controlled by the remote controller.)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller—Continued
Using the Remote Controller
The T-4355 doesn’t have its own remote controller, but
it can be controlled by using the RC-627S remote con-
troller that’s supplied with the Onkyo A-9355/A-9155
Integrated Amplifier. The T-4355 and A-9355/A-9155
must be connected with an
for this to work.
cable and an audio cable
When controlling the T-4355 with the A-9355/A-9155’s
remote controller, point the controller at the
A-9355/A-9155’s remote control sensor, as shown.
Remote control sensor
POW
ON
ER
OFF
PHON
CD
ES
PHO
NO
A
SPE
AKER
S
B
BASS
OFF
TUNER
OFF
TRE
BLE
MD
STAN
DBY
T
AP
E
ON
ON
D
OCK
MUTI
NG
PURE
DIRE
CT
LOUD
NESS
T-4355
A-9355/A-9155
30˚
30˚
5 m
RC-627S
Notes:
• The remote controller may not work reliably if the
A-9355/A-9155 is subjected to bright light, such as
direct sunlight or inverter-type fluorescent lights.
Keep this in mind when installing.
• If another remote controller of the same type is used
in the same room, or the A-9355/A-9155 is installed
close to equipment that uses infrared rays, the remote
controller may not work reliably.
• Don’t put anything, such as a book, on the remote
controller, because the buttons may be pressed inad-
vertently, thereby draining the batteries.
• The remote controller may not work reliably if the
A-9355/A-9155 is installed in a rack behind colored
glass doors. Keep this in mind when installing.
• The remote controller will not work if there’s an
obstacle between it and the A-9355/A-9155’s remote
control sensor.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the T-4355
RCA Audio Connection Color Coding
Before Making Any Connections
• Refer to the instructions that came with the com-
ponent you are connecting.
• Do not plug in the power cord until all other con-
nections are complete.
• Red connectors are used for the right channel, and
white connectors are used for the left channel.
Left (white)
L
• Do not bind audio cables with power cords and
speaker cables. Doing so may adversely affect the
sound quality.
Right (red)
R
• To prevent interference, keep power cords and
speaker cables as far away as possible from the
tuner’s antennas.
• Push each plug in all the way to make a good con-
nection (loose connections can cause noise or mal-
functions).
Right!
Wrong!
Connecting an amplifier
Use the supplied audio cable to connect the T-4355’s
ANALOG AUDIO OUTPUT L/R jacks to the analog
input jacks on the amplifier, as shown.
To use the
system functions, use the supplied
cable to make an
connection.
T-4355
Supplied
audio cable
Supplied
cable
CD
PHONO
TUNER
MD
TAPE
DOCK
POWER
BASS
TREBLE
ON
OFF
A
SPEAKERS
B
PHONES
PURE DIRECT
LOUDNESS
OFF
OFF
MUTING
R
ON
ON
STANDBY
TUNER
Amplifier
Notes:
• The T-4355 has two
so you can use either one.
• To use , you must make an audio connection
between the T-4355 and the other component.
• Use only dedicated cables for connections.
jacks. They’re both the same,
• If the T-4355 is used with another Onkyo component,
such as the A-9355/A-9155, refer to its instruction
manual as well.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the T-4355—Continued
About the System Functions
If you connect the T-4355 to another Onkyo
-capa-
Notes:
ble component with the supplied cable and audio
• Push each plug in all the way to make a good connec-
tion.
cable, you can use the following system functions.
cables are special cables solely for use with Onkyo
products.
• Use only dedicated
cables for
connections.
cables are supplied with Onkyo tuners and play-
ers (DVD, CD, etc.).
Direct Change
• Some components, including the T-4355, have two
jacks. They're both the same, so use either one.
When you select a radio preset or change the band (AM,
FM), your Onkyo amplifier will automatically select the
T-4355 as the input source.
•
jacks should be connected only to Onkyo compo-
nents. Connecting them to another manufacturer's
component may cause a malfunction.
Remote Control Operation
You can control the T-4355 by using your Onkyo ampli-
fier’s remote controller. See the amplifier’s instruction
manual for details.
• Some components may not support all
functions.
See the manuals supplied with your other Onkyo
components for more information.
With
(Remote Interactive), you can control your
-capable Onkyo CD player, T-4355, and so on with
your amplifier’s remote controller.
• To use
, you must make an analog audio con-
nection between your amplifier and each audio
component.
Onkyo amplifier
(A-9355), etc.
jack
Onkyo CD player
(DX-7355), etc.
jack
T-4355
jack
Remote Interactive
Dock, etc.
cable
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antennas
This section explains how to connect the supplied
indoor FM antenna and AM loop antenna and how to
connect commercially available outdoor FM and AM
antennas.
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use
only.
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
1
AM antenna push terminals
FM antenna jack
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
2
Connecting the Indoor FM Antenna
The antenna connection is polarity sensitive.
Connect the black wire to the ground terminal
The supplied indoor FM antenna is for indoor use only.
(
). Connect the other wire to the other terminal.
Make sure that the wires are attached securely
and that the push terminals are gripping the bare
wires, not the insulation.
Attach the FM antenna, as shown.
1
Insert the plug fully
into the jack.
Once your T-4355 is ready for use, you’ll need to
tune into an FM radio station and adjust the posi-
tion of the FM antenna to achieve the best possi-
ble reception.
Push
Insert wire
Release
Use thumbtacks or something similar to
fix the FM antenna into position.
2
Black
Once your T-4355 is ready for use, you’ll need to
tune into an AM radio station and adjust the posi-
tion of the AM antenna to achieve the best possi-
ble reception.
Thumbtacks, etc.
Keep the antenna as far away as possible from
your T-4355, TV, speaker cables, and power
cords.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commer-
cially available outdoor AM antenna.
Caution: Be careful that you don’t injure your-
self when using thumbtacks.
If you cannot achieve good reception with the supplied
indoor FM antenna, try using a commercially available
outdoor FM antenna instead.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antennas—Continued
Connecting an Outdoor FM Antenna
Connecting an Outdoor AM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try using a commercially available
outdoor FM antenna instead.
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoor AM antenna can be used
in addition to the loop antenna, as shown.
Outdoor antenna
Insulated antenna cable
AM loop antenna
White
Antenna adapter (not included)
Black
Notes:
• Outdoor FM antennas work best outside, but accept-
able results can sometimes be obtained when
installed in an attic or loft.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
Outdoor AM antennas work best when installed outside
horizontally, but good results can sometimes be
obtained indoors by mounting horizontally above a win-
dow. Note that the AM loop antenna should be left con-
nected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
• Outdoor antenna should be located away from possi-
ble noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situ-
ated well away from power lines and other high volt-
age equipment.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock haz-
ards.
Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and
TV reception, as this can cause interference problems.
If circumstances demand it, use a TV/FM antenna split-
ter, as shown.
TV/FM antenna splitter
To T-4355
To TV (or VCR)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning On the T-4355
Listening to the Radio
Tuning into Radio Stations Manually
POWER
TUNING
Plug the power cord into a suit-
1
able wall outlet (or the AC OUT-
LET on the A-9355/A-9155’s rear
panel).
BAND
Use the [BAND] button to select
FM or AM.
1
Press the T-4355’s [POWER]
switch.
The T-4355 turns on.
2
The band switches between FM and
AM each time you press the button.
To turn off the T-4355, press the
[POWER] switch.
Use the TUNING [ ]/[ ] buttons
2
to tune into a station.
The tuning frequency is shown on the
display.
Using the A-9355/A-9155’s Remote
Controller
For each button press, the frequency
will change in 0.05 MHz steps for FM,
and 9 kHz steps for AM.
ON
If you hold down the button for more
than 0.5 second, the T-4355 will find
the next station automatically.
RC-627S (remote controller supplied
with the A-9355/A-9155)
If you’re using the T-4355 together with the
A-9355/A-9155 Onkyo amplifier, press the remote con-
troller’s [ON] button to turn on the T-4355 and
A-9355/A-9155. (Plug the T-4355 power cord into the
A-9355/A-9155 AC OUTLET.)
Memory backup
The T-4355 uses a battery-less memory backup system
in order to retain radio presets and other settings when
it’s unplugged or in the case of a power failure.
Backup data can be stored incorrectly or destructed, and
lead to a malfunction if either of the following opera-
tions is performed:
• turning off the power immediately after an operation.
• repeating the fast power on/off switchings.
When a malfunction occurred due to those operations,
initialize T-4355 to its factory defaults. Radio presets
and other settings are deleted.
To initialize T-4355, press the [DISPLAY] button while
holding down the [FM MODE] button.
When the power is turned off while the Auto Preset is
running, T-4355 is initialized to its factory defaults.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
You can store up to 30 of your favorite radio stations as
presets for quick selection. Stations can be preset auto-
matically using the Auto Preset function or manually.
Presetting Stations Manually
Here you can tune into stations individually and store
them as presets. This allows you to store stations in any
order you like.
Notes:
• You can preset up to 30 AM/FM stations. If you try to
store more than this, the message “FULL” will appear
on the display.
• Using the remote controller while listening to an AM
radio station may cause interference.
Notes:
• You can store up to 30 stations, and this can be any
combination of FM and AM stations. For example, 17
FM stations and 13 AM stations, or 8 FM stations and
22 AM stations.
• Although the numbering schemes for FM and AM
presets both start at 1, it doesn’t matter because FM
and AM presets are selected independently.
• Stations can be stored to presets in any order. For
example, you could store some AM stations to presets
2, 1, 9, and so on.
Presetting All Stations Automatically
(Auto Preset)
With the Auto Preset function, you can search and store
all of the radio stations available in your area in one go.
Notes:
TUNING
MEMORY
• All existing presets will be replaced when the Auto
Preset function is used.
• Be sure that your antennas are positioned so as to
obtain the best possible reception (see page 12).
MEMORY
PRESET
BAND
Use the [BAND] button to select
FM or AM.
1
2
Press and hold the [MEMORY]
button for about 5 seconds until
auto tuning starts.
When the [MEMORY] button is
pressed, first, the MEM indicator
flashes. Next, “AUTO PRESET”
flashes on the display, followed by the
tuning frequency, and then auto tuning
starts. When a station is found, auto
The band switches between FM and
AM each time you press the button.
Press the TUNING [ ]/[ ] but-
tons for 1 second until auto tun-
ing starts.
tuning stops and the
lights up.
indicator
The frequency display changes during
auto tuning.
Auto tuning stops when a station is
found.
Starting at the bottom of the frequency
band, the T-4355 automatically tunes
and stores up to 20 FM stations, then
up to 10 AM stations.
Note:
Depending on your location, a preset may be stored
with no station and you’ll hear only noise when you
select it. In this case, delete the preset (see page 18).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Selecting Preset Stations
Press the [MEMORY] button.
3
MEM indicator
You must store some presets before you can select them
(see page 15).
The MEM indicator appears and the
preset number flashes. If you don’t
complete the next step within 8 sec-
onds, the T-4355 will return to the pre-
vious condition and the MEM
PRESET
BAND
Before proceeding, turn on the T-4355.
indicator will disappear.
Use the [BAND] button to select
FM or AM.
1
Note:
Be careful not to press the [MEM-
ORY] button for too long because
“AUTO PRESET” will flash on the
display and the Auto Preset function
will begin, replacing all of your previ-
ously stored presets.
The band switches between FM and
AM each time you press the button.
UsethePRESET [ ]/[ ]buttons
to select a preset.
Press the Down [ ] button to select
Usethe PRESET[ ]/[ ]buttons
to select a preset number from 1
through 30.
2
4
the previous preset. Press the Up [
button to select the next preset.
]
The number of the currently selected
preset is shown on the display.
Press the [MEMORY] button
5
again to store the station.
The station is stored, the preset number
stops flashing, and the MEM indicator
disappears.
Repeat this procedure for all your
favorite radio stations.
Note:
If you store a station to a preset that already had a sta-
tion stored in it, the previous station will be replaced.
After Storing Presets You Can
• Select them and enjoy your favorite stations.
• Name them for easy identification (see page 17).
• Delete them (see page 17).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Correcting Characters
Naming Presets
If Name Edit mode is not selected, follow steps 1 and 2
in the left column.
Radio presets can be named for easy identification, and
names may contain up to 8 characters from the follow-
ing selection.
DISPLAY
TUNING
_ A B C D E F G H I J K L M N O P Q R S T U V W
X Y Z
a b c d e f g h i j k l m n o p q r s t u v w x y z
" ' & ( ) [ ] * + , - . / = ? 0 1 2 3 4 5 6 7 8 9
PRESET
The underscore (_) character is actually a space.
DISPLAY
MEMORY
Use the TUNING [ ]/[ ] buttons
to select the character to edit.
1
2
PRESET
Usethe PRESET[ ]/[ ]buttons
to change the character.
Select the preset that you want to
name.
1
2
See page 16 for selecting presets.
Press and hold down the [DIS-
PLAY] button for 3 seconds to
select Name Edit mode.
Press the [DISPLAY] button to
store the name and exit Name
Edit mode.
3
The cursor appears on the display.
UsethePRESET[ ]/[ ]buttons
to select the characters.
3
Note:
Text editing features such as moving subsequent charac-
ters to the right when a new character is inserted, or
moving subsequent characters to the left when a charac-
ter is deleted are not supported.
Press the [MEMORY] button to
set the character.
4
5
The cursor moves to the next character.
Deleting All Characters in One Go
If Name Edit mode is not selected, follow steps 1 and 2
in the left column.
Repeat steps 3 and 4 to enter the
other characters. Press the [DIS-
PLAY] button when you’ve fin-
ished.
While holding down the [MEM-
ORY] button, press the [FM
FM MODE
MEMORY
The radio frequency reappears on the
display.
MODE] button.
Note:
CLEAR
Make sure that Name Edit mode is
selected before doing this because if it
isn’t, the current preset will be deleted
instead.
Hints:
• To cancel the naming process without storing the
name, press the [MEMORY] button.
• After the eighth character has been entered, pressing
the [MEMORY] button will move the cursor back to
the first character.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Deleting Presets
FM Mode
Individual presets can be deleted as follows.
In places where the signal strength is
weak or reception is noisy, press the [FM
MODE] button to listen in mono (AUTO
indicator off). This will reduce the noise
and any break up in reception.
Select the preset that you want to
delete.
See page 16 for selecting presets.
1
To return to stereo, press the [FM MODE]
button again (AUTO indicator on).
While holding down the [MEM-
ORY] button, press the [FM
2
MEMORY
FM MODE
MODE] button.
The preset number on the display dis-
appears and the preset is deleted.
Tuner Operation with the RC-627S
Remote Controller
CLEAR
(supplied with the A-9355/A-9155)
Displaying Information
By pressing the T-4355’s [DISPLAY] button repeatedly,
you can view the tuning frequency or text (preset name
or RDS).
Selecting FM or AM
This button can be used to
select FM or AM.
Frequency
Selecting Radio Presets
Press the Down [–] button
to select the previous preset.
Text (preset name or RDS)
Press the Up [+] button to
select the next preset.
Note:
Setting FM mode
This button can be used to
set the FM mode to stereo
or mono.
If the current preset doesn’t have a name, no text will be
displayed.
Tuning Manually
Press the Down [ ] button to
decrease the tuning frequency.
Press the Up [ ] button to
increase the tuning frequency.
Note:
If you’re using another Onkyo amplifier’s remote con-
troller, refer to its instruction manual for operating
information.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Using RDS
(European models only)
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. Many FM sta-
tions use it these days.
The T-4355 supports the following types of RDS data:
PS: Program Service Name
When tuned to an RDS station that’s broadcasting PS
information, the station’s name appears on the display.
RT: Radio Text
When tuned to an RDS station that’s broadcasting RT
text information, the text scrolls across the display.
Note:
If the signal from an RDS station is weak, RDS data
maybe displayed intermittently or not at all.
Displaying RDS information
Note:
You must be tuned to an FM station that supports RT
(Radio Text) in order to display any text.
DISPLAY
Press the [DISPLAY] button
repeatedly to show the following
information.
Frequency
Preset name or PS
(Program Service name)
RT (Radio Text)
Notes:
• If the current station does not support RDS, only the
frequency and preset name (see page 17) will be dis-
played. If the current preset has no name, only the
frequency will be displayed.
• In some cases, it may take between 2 and 15 seconds
for the RT text to be displayed.
• The message “Waiting···” may appear while the RT
data is being received.
• When tuned to an RDS station that’s not transmitting
any RT data, the message “No Text” will be dis-
played.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have any trouble using the T-4355, look for a solution here. If you can’t resolve the issue yourself, contact your
Onkyo dealer.
Power
Can’t turn on the T-4355.
• Make sure that the power cord is properly plugged into the wall outlet (page 14).
• Unplug the power cord from the wall outlet, wait five seconds or more, then plug it in again.
Audio
There’s no sound.
• The T-4355 is not connected properly. Check all connections and correct as necessary.
• The wrong input source is selected on your amplifier. Check your amplifier’s input source setting. Refer to your
amplifier’s manual.
• Make sure the amplifier’s volume control is not set to minimum.
Radio
Reception is noisy, stereo FM reception suffers from hiss, the Auto Preset function doesn’t preset all
stations, or the ST indicator doesn’t light up when tuned to a stereo FM station.
• Check the antenna connections.
• Change the position of the antenna.
• Move the T-4355 away from a nearby TV or computer.
• Move power cords and speaker cables as far away as possible from the tuner’s antenna.
• Cars or airplanes can cause noisy interference.
• The radio signal will be weakened if it has to pass through a concrete wall before reaching the antenna.
• Try setting FM mode to mono.
• When listening to an AM station, noise may be heard when you operate the remote controller.
• If none of the above improves the reception, install an outdoor antenna.
Settings such as radio presets were deleted.
• Backup data can be stored incorrectly or destructed, and lead to a malfunction if either of the following operations is
performed:
- turning off the power immediately after an operation.
- repeating the fast power on/off switchings.
• When a malfunction occurred due to those operations, initialize T-4355 to its factory defaults (see below), then set
radio presets or other settings again.
Remote Controller
The A-9355/A-9155’s remote controller doesn’t work.
• Point the remote controller at the A-9355/A-9155’s remote sensor (page 9).
• To use
(page 11).
, you must make an
connection and an audio connection between the A-9355/A-9155 and T-4355
The T-4355 contains a microcomputer for signal processing and control functions. In very rare
situations, severe interference, noise from an external source, or static electricity may cause it to
lockup. In the unlikely event that this should happen, unplug the power cord, wait at least five
seconds, and then plug it again.
To reset the T-4355 to its factory defaults, turn it on and, while holding down the [FM MODE]
button, press the [DISPLAY] button. “CLEAR” will appear on the display.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
FM
Tuning frequency range:
87.50–108.00 MHz
Usable sensitivity:
Stereo: 17.2 dBf 2.0 µV (75: IHF)
Mono: 11.2 dBf 1.0 µV (75: IHF)
Stereo: 70 dB (IHF-A)
Mono: 76 dB (IHF-A)
Stereo: 0.3% (1 kHz)
SN ratio:
THD (total harmonic distortion):
Mono: 0.2% (1 kHz)
Frequency response:
Stereo separation:
20 Hz–15 kHz / 1.5 dB
45 dB (1 kHz)
AM
Tuning frequency range:
522–1611 kHz
530–1710 kHz
30 µV
Usable sensitivity:
SN ratio:
50 dB
THD (total harmonic distortion):
0.7%
General
Power supply:
European model: AC 2ꢀ0–230 V, 50/60 Hz
Asian model: AC 1ꢀ0/220–240 V, 50/60 Hz
European model: 9 W
Asian model: 10 W
435 u 81 u 310 mm
17-1/8s u 3-3/16s u 12-3/16s
3.2 kg
Power consumption:
Dimensions (W u H u D):
Weight:
7.1 lbs.
Specifications and features are subject to change without notice.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
HOMEPAGE
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
Y0702-2
SN 29344431A
(C) Copyright 2007 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 4 4 3 1 A *
Download from Www.Somanuals.com. All Manuals Search And Download.
|