Contents
Introduction ..................................... 2
5.1ch Home Theater System
Connection .................................... 17
Turning On & First Time Setup..... 32
HT-S580
AV Receiver (HT-R330)
Front Speakers (SKF-330F L/R)
Center Speaker (SKC-330C)
Surround Speakers (SKM-330S L/R)
Subwoofer (SKW-330)
Basic Operation
Playing your AV components....... 36
Using the Tuner............................ 38
Instruction Manual
Enjoying the Listening Modes ..... 44
Advanced Operation..................... 47
Thank you for purchasing an Onkyo 5.1ch Home
Theater System. Please read this manual thoroughly
before making connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new 5.1ch Home Theater Sys-
tem.
Please retain this manual for future reference.
Troubleshooting............................ 53
Specification.................................. 56
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal with-
out the permission of the copyright holder.
Memory Backup
The AV receiver uses a battery-less memory backup
system in order to retain radio presets and other settings
when it’s unplugged or in the case of a power failure.
Although no batteries are required, the AV receiver
must be plugged into an AC outlet in order to charge the
backup system. Once it has been charged, the AV
receiver will retain the settings for several weeks,
although this depends on the environment and will be
shorter in humid climates.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild deter-
gent and water. Dry the unit immediately afterwards
with a clean cloth. Don’t use abrasive cloths, thin-
ners, alcohol, or other chemical solvents, because
they may damage the finish or remove the panel let-
tering.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue:
Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
Some models have a voltage selector switch for
compatibility with power systems around the world.
Before you plug in such a model, make sure that the
voltage selector is set to the correct voltage for your
area.
Setting the [STANDBY/ON] switch to STANDBY
does not fully shutdown the unit. If you do not
intend to use the unit for an extended period,
remove the power cord from the AC outlet.
5. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the same
ampere rating as that indicated on the plug. Check for
the ASTA mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut if off and fit a suitable plug. Fit a suitable
fuse in the plug.
6. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you origi-
nally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
For European Models
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
I. MORI
ONKYO EUROPE ELECTRONICS GmbH
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Precautions
Precautions—Continued
Placement
For U.S. models
• The subwoofer cabinet is made out of wood and is
therefore sensitive to extreme temperatures and
humidity, do not put it in locations subject to direct
sunlight or in humid places, such as near an air condi-
tioner, humidifier, bathroom, or kitchen.
• Do not put water or other liquids close to the speakers.
If liquid is spilled over the speakers, the drive units
may be damaged.
• Speakers should only be placed on sturdy, flat surfaces
that are free from vibration. Putting them on uneven or
unstable surfaces, where they may fall and cause dam-
age, will affect the sound quality.
FCC Information for User
CAUTION:
The user changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Subwoofer is designed to be used in the upright verti-
cal position only. Do not use it in the horizontal or
tilted position.
• If the unit is used near a turntable or CD player, howl-
ing or slipping of sound may occur. To prevent this,
move the unit away from the turntable or CD player
otherwise lower the unit’s output level.
Using Close to a TV or Computer
TVs and computer monitors are magnetically sensitive
devices and as such are likely to suffer discoloration or
picture distortion when conventional speakers are
placed nearby. To prevent this, the SKF-330F and
SKC-330C feature internal magnetic shielding. In some
situations, however, discoloration may still be an issue,
in which case you should turn off your TV or monitor,
wait 15 to 30 minutes, and then turn it back on again.
This normally activates the degaussing function, which
neutralizes the magnetic field, thereby removing any
discoloration effects. If discoloration problems persist,
try moving the speakers away from your TV or monitor.
Note that discoloration can also be caused by a magnet
or demagnetizing tool that’s too close to your TV or
monitor.
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
•
•
Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV tech-
nician for help.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Do not place SKM-330 close to TV or a computer mon-
itor because they have no magnetic shield.
Modèle canadien
Input Signal Warning
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
The speakers can handle the specified input power when
used for normal music reproduction. If any of the fol-
lowing signals are fed to them, even if the input power is
within the specified rating, excessive current may flow
in the speaker coils, causing burning or wire breakage:
1. Interstation noise from an untuned FM radio.
2. Sound from fast-forwarding a cassette tape.
3. High-pitched sounds generated by an oscillator,
electronic musical instrument, and so on.
4. Amplifier oscillation.
5. Special test tones from audio test CDs and so on.
6. Thumps and clicks caused by connecting or discon-
necting audio cables (Always turn off your amplifier
before connecting or disconnecting cables.)
7. Microphone feedback.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Amp
Introduction
• 6-channel amplifier
Important Safety Instructions.................2
Before Using the AV receiver................... 7
Front & Rear Panels ................................8
• 100 watts per channel min. RMS at 8 Ω, 2 channels
driven from 1 kHz with no more than 0.9% total har-
monic distortion
• WRAT (Wide Range Amplifier Technology)
• Optimum gain volume circuitry
*1
• OptiResponse™ Equalizer (OR-EQ™) function
Processing
*2
• Dolby Digital and Dolby Pro Logic II
*3
• DTS and DTS Neo:6 processing
Connection
• Cinema Filter function
• Linear PCM 192 kHz/24-bit D/A converters on all
channels
Connecting Your Speakers...................17
• Powerful and highly accurate 32-bit DSP Processing
Audio/Video
Turning On & First Time Setup
• Adjustable crossover (60, 80, 100, 120, 150 Hz)
• 2 assignable digital inputs (1 optical, 1 coaxial)
• Color-coded multichannel input for use with Super
Audio CD and DVD-Audio
• A/B speaker drive
• Color-coded speaker terminal
Basic Operation
Playing Your AV Components..............36
Common Functions...............................42
FM/AM Tuner
• 30 FM/AM presets
• FM/AM auto tuning
Enjoying the Listening Modes
• RDS (Radio Data System) (Europe only)
Remote Controller
• Remote controller can be used to control Onkyo CD,
CDR, MD components, and cassette tape deck
Advanced Operation
Recording...............................................49
Front / Center / Surround Speakers
• Color-coded speaker terminals and speaker cables
• 3-1/8" (8 cm) cone woofer
• Ceramic tweeter
Troubleshooting .................................... 53
Specification.......................................... 56
Subwoofer
• Down-Firing Subwoofer
• Heavy-Duty Long-Throw woofer
• Color-coded speaker terminals and speaker cables
*1. OptiResponse and OR-EQ are trademarks of Onkyo Cor-
poration.
*2. Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are regis-
tered trademarks of Dolby Laboratories.
*3. “DTS” and “Neo:6” are trademarks of Digital Theater Sys-
tems, Inc.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
Make sure you have the following accessories:
HT-R330
HTP-330
Front speakers
(SKF-330F L/R)
HT-R330
Center speaker
(SKC-330C)
Remote controller & two batteries (AA/R6)
Surround speakers
(SKM-330S)
Indoor FM antenna
(Connector type varies from country to country.)
Subwoofer (SKW-330)
AM loop antenna
(Red)
(White)
Speaker cable for front speakers 15 ft. (4.5 m)
(Green)
Power-plug adapter
Only supplied in certain countries. Use this adapter if
your AC outlet does not match with the plug on the AV
receiver’s power cord. (Adapter varies from country to
country.)
Speaker cable for center speaker 10 ft. (3 m)
*
In catalogs and on packaging, the letter at the end of the
product name indicates the color. Specifications and oper-
ation are the same regardless of color.
(Blue)
(Gray)
Speaker cables for surround speakers 30 ft. (9 m)
(Purple)
Speaker cables for subwoofer 15 ft. (4.5 m)
Rubber stoppers [20]
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using the AV receiver
Notes:
Setting the Voltage Selector
(on some models)
• The batteries should last for about six months,
although this will vary with usage.
Some models have a voltage selector switch for compat-
ibility with power systems around the world. Before you
plug in this model, make sure that the voltage selector is
set to the correct voltage for your area. If it isn’t, use a
small screwdriver to set it as appropriate. For example, if
the voltage in your area is 120 volts, set the selector to
“120V.” If it’s between 220 and 230 volts, set it to “220-
230V.”
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as possi-
ble to prevent damage from leakage or corrosion.
VOLTAGE
SELECTOR
120
V
Using the Remote Controller
-
220 230
V
To use the remote controller, point it at the AV receiver’s
remote control sensor, as shown below.
Remote control sensor
AV receiver
Installing the Batteries
STANDBY indicator
To open the battery compartment, press
the small hollow and slide open the cover.
1
Approx. 16 ft.
(5 m)
Notes:
• The remote controller may not work reliably if the AV
receiver is subjected to bright light, such as direct sun-
light or inverter-type fluorescent lights. Keep this in
mind when installing.
Insert the two supplied batteries (AA/R6)
in accordance with the polarity diagram
inside the battery compartment.
2
• If another remote controller of the same type is used in
the same room, or the AV receiver is installed close to
equipment that uses infrared rays, the remote control-
ler may not work reliably.
• Don’t put anything, such as a book, on the remote con-
troller, because the buttons may be pressed inadvert-
ently, thereby draining the batteries.
• The remote controller may not work reliably if the AV
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
• The remote controller will not work if there’s an obsta-
cle between it and the AV receiver’s remote control
sensor.
Slide the cover shut.
3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Front & Rear Panels
Front Panel
North American and Asian Models
1
2
3
4 5 6 7 8 9 J K
L
M
TUNING
/
PRESET
MASTER VOLUME
STANDBY/ON
ENTER
STANDBY
RETURN
SETUP
A
SPEAKERS
PHONES
B
TONE
+
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
DIMMER
MEMORY TUNING MODE
CLEAR
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
N O
P
Q
R
S
European Models
9
TUNING
/
PRESET
MASTER VOLUME
STANDBY/ON
ENTER
STANDBY
RETURN
SETUP
A
SPEAKERS
PHONES
B
TONE
+
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
F Display
See “Display” on page 9.
A STANDBY/ON button (32)
This button is used to set the AV receiver to On or
Standby.
G DISPLAY button (37)
This button is used to display various information
about the currently selected input source.
B STANDBY indicator (32)
This indicator lights up when the AV receiver is in
Standby mode, and it flashes while a signal is being
H DIGITAL INPUT button (33)
This button is used to assign the digital inputs and to
specify the format of digital input signals.
C Remote-control sensor (7)
This sensor receives control signals from the remote
controller.
This button is used to adjust the display brightness.
On the European model, this is the RT/PTY/TP but-
ton, and it’s used with RDS (Radio Data System).
See “Using RDS (European models only)” on
page 40.
D STEREO button (44)
This button is used to select the Stereo listening
mode.
E LISTENING MODE [ ]/[ ] buttons (44)
These buttons are used to select the listening modes.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Front & Rear Panels—Continued
J MEMORY button (39)
This button is used when storing or deleting radio
presets.
O SPEAKER A & B buttons (36)
on or off.
K TUNING MODE button (38)
This button is used to select the Auto or Manual tun-
ing mode.
P TONE, [–] & [+] buttons (42)
These buttons are used to adjust the bass and treble.
Q Input selector buttons (36)
L Arrow/TUNING/PRESET & ENTER buttons
When the AM or FM input source is selected, the
TUNING [ ] [ ] buttons are used to tune the
to select radio presets (see page 39). When the setup
menus are used, they work as arrow buttons and are
used to select and set items. The ENTER button is
These buttons are used to select from the following
input sources: MULTI CH, DVD, VIDEO 1/VCR,
VIDEO 2, VIDEO 3, TAPE, TUNER, or CD.
The [MULTI CH] button selects the DVD analog
multichannel input.
R RETURN button
This button is used to return to the previously dis-
played setup menu.
M MASTER VOLUME control (36)
This control is used to adjust the volume of the AV
receiver to MIN, 1 through 79, or MAX
S SETUP button
This button is used to access various settings.
N PHONES jack (43)
This 1/4-inch phone jack is for connecting a stan-
dard pair of stereo headphones for private listening.
Display
1
2
3
4
5
6
RDS (European model only) (40): This indica-
tor lights up when the AV Receiver is tuned to a
tem).
1 A & B speaker indicators (36)
Indicator A lights up when speaker set A is on. Indi-
cator B lights up when speaker set B is on.
MEMORY (39): This indicator lights up when pre-
setting radio stations.
2 MUTING indicator (42)
This indicator flashes when the AV receiver is
muted.
FM STEREO (38): This indicator lights up when
the AV receiver is tuned to a stereo FM station.
These indicators show the currently selected listen-
5 SLEEP indicator (43)
This indicator lights up when the Sleep function has
been set.
4 Tuning indicators (38)
6 Message area
TUNED (38): This indicator lights up when the AV
This area of the display shows various information
about the currently selected source.
receiver is tuned to a radio station.
AUTO (38): This indicator lights up when Auto
Tuning is selected and disappears when Manual
Tuning is selected.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Front & Rear Panels—Continued
Rear Panel
1
B
3
4
5
6
7
8
9 J
K
L
A DIGITAL IN OPTICAL & COAXIAL
I CD IN
These optical and coaxial jacks can be used to con-
nect a CD or DVD player and other components
with digital audio outputs.
These analog inputs can be used to connect a CD
player with analog outputs.
J TAPE IN/OUT
B AM ANTENNA
These analog inputs and outputs can be used to con-
nect a cassette recorder, MiniDisc recorder, or other
recorder with analog inputs and outputs.
These push terminals are for connecting an AM
antenna.
C FM ANTENNA
K VIDEO 1 IN/OUT, VIDEO 2 IN & VIDEO 3 IN
The VIDEO 1, composite video, and audio inputs
and outputs can be used to connect a VCR. The
VIDEO 2, VIDEO 3, composite video, and audio
inputs can be used to connect another video source
(e.g., cable TV, satellite TV, or a set-top box).
This jack is for connecting an FM antenna.
D MONITOR OUT
The composite video output should be connected to
a video input on your TV or projector.
E FRONT SPEAKERS B
These push terminals are for connecting speaker
set B.
L DVD IN/MULTI CH INPUT
The FRONT, SURROUND, CENTER, and SUB-
WOOFER jacks can be used to connect a compo-
nent with an analog multichannel audio output, such
as a DVD player with a 5.1-channel analog output.
The composite video input should be connected to a
video output on the DVD player.
F FRONT SPEAKERS A, SURROUND
SPEAKERS & CENTER SPEAKER
These push terminals are for connecting speaker
set A.
G VOLTAGE SELECTOR (only some models)
This voltage selector provides compatibility with
power systems around the world.
H
This
nected to the
nent. The AV receiver’s remote controller can then
(Remote Interactive) jack can be con-
jack on another Onkyo compo-
be used to control that component. To use
, you
must make an analog audio connection (RCA)
between the AV receiver and the other component,
even if they are connected digitally.
Note:
can only be used with Onkyo components.
See pages 17–31 for connection information.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Package
Front, Center, Surround, & Subwoofer speakers
(SKF-330F, SKC-330C, SKM-330S, SKW-330)
A Speaker terminals
■ Rear
These push terminals are for connecting the speaker
to the HT-R330 with the supplied speaker cables.
easy identification. Simply connect each cable to the
same-colored positive speaker terminal.
SKF-330F
SKM-330S
2
B Keyhole slots
These keyhole slots can be used to wall-mount the
speaker. See page 19 for mounting instructions.
C Speaker mount/bracket inserts
These threaded inserts can be used to attach the
speaker to a speaker mount or bracket. See page 19
for mounting instructions.
Note:
3
1
Use commercially available machine screws to
attach the speaker to a speaker mount or bracket.
North American models require 1/4-inch screws.
Other models require M5 (5 mm) screws.
2
2
SKC-330C
3
1
SKW-330
1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
How to Use the Remote Controller
RECEIVER Mode
Including the AV receiver, the remote controller can be
used to control up to six different components. The
remote controller has a specific operating mode for use
with each type of component. Modes are selected by
using the five REMOTE MODE buttons.
RECEIVER mode is used to control the AV receiver.
To set the remote controller to RECEIVER mode,
press the [RECEIVER] REMOTE MODE button.
A
RECEIVER
■ RECEIVER/TAPE Mode
ON
STANDBY
REMOTE MODE
In RECEIVER/TAPE mode, you can control
the AV receiver and an Onkyo cassette
RECEIVER
DVD
B
C
TAPE/AMP
INPUT SELECTOR
recorder connected via
.
CD
1
2
3
V
1
V
2
V3
■ DVD, CD, MD, & CDR Modes
With these modes, you can control an
Onkyo DVD player and CD/MD/CDR
player/recorder.
MD
4
5
6
DVD
CD
M
N
O
D
MULTI CH
DVD
CDR
7
8
9
TAPE
TUNER
CD
+
10
CLR
0
MD
-- ---
/
DIMMER
SLEEP
E
F
CDR
CH
VOL
DISC
TOP MENU
SP A/B
MENU
P
Q
G
H
Use the REMOTE MODE buttons to select
a mode.
1
2
MUTING
ENTER
Use the buttons supported by that mode
to control the component.
RECEIVER mode: see page 12
DVD mode: see page 14
I
RETURN
SETUP
CD/MD/CDR mode: see page 15
TAPE mode: see page 16
LISTENING MODE
STEREO
SURROUND
J
K
Note:
AUDIO SUBTITLE RANDOM REPEAT
Some of the remote controller operations described in
this manual may not work as expected with other com-
ponents.
-
+
LEVEL
TEST TONE
DISPLAY
CH SEL
LEVEL
PLAY MODE
OR-EQ
L NIGHT
CINE FLTR
R
S
L
T
-
RC 606S
12
Download from Www.Somanuals.com. All Manuals Search And Download.
O VOL [ ]/[ ] button (36)
This button can be used to adjust the volume of the
AV receiver regardless of the currently selected
remote controller mode.
A STANDBY button (32)
This button is used to set the AV receiver to
Standby.
P MUTING button (42)
This button is used to mute the AV receiver.
B ON button (32)
This button is used to turn on the AV receiver.
Q SETUP button
C INPUT SELECTOR buttons (36)
This button is used to access various settings.
These buttons are used to select the input sources.
R CINE FLTR button (48)
D MULTI CH button (37)
This button is used to select the multichannel DVD
input.
This button is used to set the CinemaFILTER func-
tion.
S L NIGHT button (48)
E DIMMER button (42)
This button is used to set the Late Night function.
This button is used to adjust the display brightness.
T OR-EQ button (42)
F CH +/– button (39)
This button is used to turn on the OptiResponse
equalizer, which optimizes performance when the
HT-R330 is used with the speakers included in the
HTP-330 Home Theater Speaker Package. When
the OptiResponse equalizer is on, you can enjoy a
powerful sound with movies or music with small
volume.
This button is used to select radio presets.
G SP A/B button (36)
This button is used to turn speaker sets A and B on
or off.
These buttons are used to select and adjust settings.
I RETURN button
This button is used to return to the previous display
when changing settings.
J LISTENING MODE buttons (44)
These buttons can be used to select listening modes
regardless of the currently selected remote control-
ler mode.
STEREO button
This button selects the Stereo listening mode.
SURROUND button
This button selects the Dolby and DTS listening
modes.
[
]/[ ] buttons
These buttons can be used to select any of the avail-
able listening modes.
K TEST TONE, CH SEL, LEVEL- & LEVEL+
buttons (35)
These buttons are used to adjust the level of each
speaker.
L DISPLAY button (37)
This button is used to display various information
about the currently selected input source.
These buttons are used to select the remote control-
ler modes. When you press a button on the remote
controller, the REMOTE MODE button for the cur-
rently selected mode lights up.
N SLEEP button (43)
This button is used to set the Sleep function.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller—Continued
A STANDBY button
DVD Mode
This button sets the DVD player to Standby.
To set the remote controller to DVD mode, press the
[DVD] REMOTE MODE button.
B ON button
This button is used to turn on the DVD player.
C Number buttons
Before selecting DVD mode and starting play-
back, you should press the [RECEIVER] mode
button followed by the [DVD] INPUT SELEC-
TOR button to select the DVD player as the
input source.
These buttons are used to enter title, chapter, and
track numbers and to enter times for locating spe-
cific points in time.
D DISC +/– button
This button selects discs on a DVD changer.
E TOP MENU button
This button is used to select a DVD’s top menu.
F Arrow [ ]/[ ]/[ ]/[ ] & ENTER buttons
These buttons are used to navigate DVD menus and
the DVD player’s onscreen setup menus.
A
ON
STANDBY
REMOTE MODE
G RETURN button
RECEIVER
DVD
B
C
DVD
TAPE/AMP
This button is used to exit the DVD player’s
onscreen setup menu and to restart menu playback.
INPUT SELECTOR
CD
1
2
3
V
1
V
2
V3
H Playback buttons
MD
4
5
6
From left to right: Pause, Play, Stop, Fast Reverse,
Fast Forward, Previous, and Next.
MULTI CH
DVD
CDR
7
8
9
TAPE
TUNER
CD
I SUBTITLE button
+
10
CLR
0
This button is used to select subtitles.
L
-- ---
/
DIMMER
SLEEP
J AUDIO button
This button selects foreign language soundtracks
and audio formats (e.g., Dolby Digital or DTS).
CH
VOL
DISC
D
K DISPLAY button
TOP MENU
SP A/B
MENU
This button is used to display information about the
current disc, title, chapter, or track on the DVD
player’s display, including the elapsed time, remain-
ing time, total time, and so on.
E
F
M
N
MUTING
ENTER
L CLR button
G
H
This button is used to cancel functions and to clear
entered numbers.
RETURN
SETUP
M MENU button
This button is used to display a DVD’s menu.
N SETUP button
LISTENING MODE
This button is used to access the DVD player’s
onscreen setup menus.
STEREO
SURROUND
O
P
I
J
AUDIO SUBTITLE RANDOM REPEAT
-
+
LEVEL
TEST TONE
DISPLAY
CH SEL
LEVEL
O RANDOM button
PLAY MODE
OR-EQ
This button is used with the random playback func-
tion.
L NIGHT
CINE FLTR
K
Q
P REPEAT button
This button is used to set the repeat playback func-
tions.
-
RC 606S
Q PLAY MODE button
This button is used to select play modes on a com-
ponent with selectable play modes.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller—Continued
A STANDBY button
CD, MD, & CDR Mode
This button sets the CD player or MD/CD recorder
to Standby.
To set the remote controller to CD, MD, or CDR
mode, press the [CD], [MD], or [CDR] REMOTE
MODE button.
B ON button
This button is used to set the CD player or MD/CD
recorder to On or Standby.
Before selecting a mode and starting playback,
you should press the [RECEIVER] mode but-
ton followed by the [CD] or [TAPE] INPUT
SELECTOR button to select the CD player,
MiniDisc, or CD recorder as the input source.
C Number buttons
These buttons are used to enter track numbers and
to enter times for locating specific points in time.
D DISC +/– button
This button selects discs on a CD changer.
E Playback buttons
From left to right: Pause, Play, Stop, Fast Reverse,
Fast Forward, Previous and Next.
A
F DISPLAY button
ON
STANDBY
REMOTE MODE
This button is used to display information about the
current disc or track on the CD player or MD/CD
recorder’s display, including the elapsed time,
remaining time, total time, and so on.
RECEIVER
DVD
B
C
TAPE/AMP
INPUT SELECTOR
CD
CD
MD
CDR
G
1
2
3
V
1
V
2
V3
MD
4
5
6
G CLR button
MULTI CH
DVD
This button is used to cancel functions and to clear
entered numbers.
CDR
7
8
9
TAPE
TUNER
CD
+
10
H RANDOM button
CLR
0
-- ---
/
DIMMER
SLEEP
This button is used with the random playback func-
tion.
CH
VOL
DISC
D
I REPEAT button
This button is used to set the repeat playback func-
tions.
TOP MENU
SP A/B
MENU
J PLAY MODE button
MUTING
This button is used to select play modes on a com-
ponent with selectable play modes.
ENTER
RETURN
SETUP
E
F
LISTENING MODE
STEREO
SURROUND
8
9
AUDIO SUBTITLE RANDOM REPEAT
-
+
LEVEL
TEST TONE
DISPLAY
CH SEL
LEVEL
PLAY MODE
OR-EQ
L NIGHT
CINE FLTR
J
-
RC 606S
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller—Continued
A Play [ ] button
TAPE Mode
This button is used to start playback.
TAPE mode is used to control an Onkyo cassette
recorder connected to the AV receiver via
B Stop [ ] button
.
This button is used to stop playback.
To set the remote controller to TAPE mode, press the
[RECEIVER] REMOTE MODE button.
C Reverse Play [ ] button
This button is used to start reverse playback.
Before selecting TAPE mode and starting play-
back, you should press the [RECEIVER]
REMOTE MODE button followed by the [TAPE]
INPUT SELECTOR button to select your cas-
sette recorder as the input source.
D Rewind & FF [ ]/[ ] buttons
The Rewind [ ] button is used to start rewind. The
FF [ ] button is used to start fast forward.
For twin cassette decks, only deck B can be controlled.
RECEIVER
ON
STANDBY
REMOTE MODE
RECEIVER
DVD
TAPE/AMP
INPUT SELECTOR
CD
1
2
3
V
1
V
2
V3
MD
4
5
6
MULTI CH
DVD
CDR
7
8
9
TAPE
TUNER
CD
+
10
CLR
0
-- ---
/
DIMMER
SLEEP
CH
VOL
DISC
TOP MENU
SP A/B
MENU
MUTING
ENTER
RETURN
SETUP
A
B
C
LISTENING MODE
D
STEREO
SURROUND
AUDIO SUBTITLE RANDOM REPEAT
-
+
LEVEL
TEST TONE
DISPLAY
CH SEL
LEVEL
PLAY MODE
OR-EQ
L NIGHT
CINE FLTR
-
RC 606S
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Speakers
Enjoying Home Theater
You can use two sets of speakers with the AV receiver: speaker set A and speaker set B.
Speaker set A should be installed in your main listening room and can be used with Dolby Digital and DTS surround
material. Each speaker must be positioned at a specific location in your listening room to get the best from surround
sound material. The following illustration shows the best positions for your surround-sound speakers. When speaker set
B is turned on, speaker setA is reduced to 2.1-channel playback. If the multichannel DVD input is selected, and speaker
set B is turned on, speaker set A is reduced to 2-channel playback.
Speaker set B can be installed in another room. Speakers can be positioned in the standard position for stereo speakers
or however you like.
Front left and right speakers (SKF-330F L/R)
These output the overall sound. Their role in a home theater is to provide a solid anchor for
the sound image. They should be positioned facing the listener at about ear level, and equi-
distant from the TV. Angle them inward so as to create a triangle, with the listener at the apex.
Center speaker (SKC-330C)
This speaker enhances the front left
and right speakers, making sound
movements distinct and providing a
full sound image. In movies it’s used
mainly for dialog.
Position it close to yourTV (preferably
on top) facing forward at about ear
level, or at the same height as the
front left and right speakers.
Subwoofer (SKW-330)
The subwoofer handles the bass sounds of
the LFE (Low-Frequency Effects) channel.
The volume and quality of the bass output
from your subwoofer will depend on its posi-
tion, the shape of your listening room, and
your listening position. In general, a good
bass sound can be obtained by installing the
subwoofer in a front corner,
Surround left and right speakers
or at one-third the width of
(SKM-330S L/R)
the wall, as shown.
These speakers are used for precise sound
positioning and to add realistic ambience.
Position them at the sides of the listener, or
slightly behind, about 2–3 feet (60–100 cm)
above ear level. Ideally they should be equi-
distant from the listener.
Corner
1/3 wall
length
To get the very best from your surround-sound system, you should also specify the distance between the listener and
each individual speaker so that the sound from each speaker arrives at the listener’s ears at the same time (see page 51).
In addition, you should set the level of each individual speaker to achieve an equal balance (see page 51.)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Speakers—Continued
Speaker Connection Precautions
Connecting Speaker
Read the following before connecting your speakers:
• You can connect speakers with an impedance of
8 ohms or higher. If you use speakers with a lower
impedance, and use the amplifier at high volume lev-
els for a long period of time, the built-in protection
circuit may be activated.
The AV receiver’s positive (+) speaker terminals are
color-coded for ease of identification. (The negative (–)
speaker terminals are all black.)
Speaker terminal
Front left
Color
White
Red
Front right
• Disconnect the power cord from the wall outlet before
making any connections.
Center
Green
Blue
Surround left
Surround right
Subwoofer
Gray
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals to only positive
(+) terminals, and negative (–) terminals to only nega-
tive (–) terminals. If you get them the wrong way
around, the sound will be out of phase and will sound
unnatural.
Purple
Strip 3/8" (10 mm) of insu-
lation from the ends of the
speaker cables. (Supplied
speaker cables are already
stripped.)
3/8" (10 mm)
1
2
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the
positive and negative wires.
Doing so may damage the AV
receiver.
While pressing the lever, insert
the wire into the hole, and then
release the lever.
Make sure that the terminals are
gripping the bare wires, not the
insulation.
• Don’t connect more than one
cable to each speaker termi-
nal. Doing so may damage the
AV receiver.
Note:
When speaker set B is turned on, speaker setA is reduced
to 2.1-channel playback.
• Don’t connect one speaker to several terminals.
The following illustration shows which speaker should
be connected to each pair of terminals.
Purple
White
Red
Green
Gray
Blue
Subwoofer
Surround
right
Surround
left
Center speaker
Front right
speaker
Front left
speaker
speaker
speaker
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Speakers—Continued
Wall Mounting
Using Speaker Mounts/Brackets
The speakers can easily be wall mounted by using the
keyhole slots. To prevent the speaker from vibrating
against the wall, attach four of the supplied spacers to the
keyhole fins on the rear of each speaker.
Threaded inserts for machine screws are provided on the
rear of each speaker for wall-mounting with commer-
cially available speaker mounts or brackets. North
American models require 1/4-inch screws. Other models
require M5 (5 mm) screws. Refer to the manual supplied
with your mounts or brackets for installation details.
To mount the front or surround speakers vertically, use
the keyhole slot shown to hang each speaker on a screw
that’s securely screwed into the wall.
Front speaker (SKF-330F)
Surround speaker (SKM-330S)
Threaded
insert
Keyhole slot for
wall mounting
Note:
The portion of the screw that goes into the speaker’s
threaded insert should be between 1/4" – 5/16" (5 mm –
8 mm) long.
To mount the center speaker horizontally, use the two
keyhole slots shown to hang each speaker on two screws
that are securely screwed into the wall.
Mount or bracket
Center speaker (SKC-330C)
Keyhole slots for wall
mounting
(North American model)
1/4"
(Other models)
5 mm
1/4" – 5/16"
(5 mm) – (8 mm)
Using Rubber Stoppers with the
Speakers
5-7/8" (150 mm)
We recommend using the provided rubber stoppers to
achieve the best possible sound from your speakers. The
rubber stoppers prevent the speakers from moving, pro-
viding a more stable setup.
Caution:
A mounting screw’s ability to support a speaker depends
on how well it’s anchored to the wall. If you have hollow
walls, screw each mounting screw into a stud. If there are
no studs, or the walls are solid, use suitable wall anchors.
Use screws with a head diameter of 5/16" (9 mm) or less
and a shank diameter of 1/8" (4 mm) or less. With hollow
walls, use a cable/pipe detector to check for any power
cables or water pipes before making any holes.
Leave a gap of between
Rubber stoppers
Bottom of the
SKF-330F/
SKM-330S
3" (75 mm)
Wall
5/16" (7 mm) and 7/16"
(10 mm)betweenthewall
and the base of the screw
head, as shown.
Bottom of the
SKC-330C
(We recommend that you
consult a home installa-
tion professional.)
5/16" – 7/16"
(7 mm) – (10 mm)
7" (175 mm)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antenna
This section explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
The AV receiver won’t pick up any radio signals without
any antenna connected, so you must connect the antenna
to use the tuner.
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use
only.
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
1
AM antenna push terminals
FM antenna jack
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
2
Connecting the Indoor FM Antenna
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around).
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
The supplied indoor FM antenna is for indoor use only.
Attach the FM antenna, as shown.
1
■ American Model
Push
Insert wire
Release
Insert the plug fully into the jack.
Once your AV receiver is ready for use, you’ll
need to tune into an AM radio station and adjust
the position of theAM antenna to achieve the best
possible reception.
■ Other Models
Keep the antenna as far away as possible from
cords.
Insert the plug fully
into the jack.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commer-
cially available outdoor AM antenna (see page 21).
Once your AV receiver is ready for use, you’ll
need to tune into an FM radio station and adjust
the position of the FM antenna to achieve the best
possible reception.
Fully extend the antenna and point it in
2
various directions to find the best recep-
tacks or something similar.
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead (see page 21).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antenna—Continued
Connecting an Outdoor FM Antenna
Connecting an Outdoor AM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead.
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoorAM antenna can be used in
addition to the loop antenna, as shown.
Outdoor antenna
Insulated antenna cable
AM loop antenna
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in an
attic or loft.
Outdoor AM antennas work best when installed outside
horizontally, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
• Outdoor antenna should be located away from possi-
ble noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock haz-
ards.
■ Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If cir-
cumstances demand it, use a TV/FM antenna splitter, as
shown.
TV/FM antenna splitter
To AV receiver
To TV (or VCR)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components
AV Connection Color Coding
About AV Connections
RCA-type AV connections are usually color coded: red,
white, and yellow. Use red plugs to connect right-chan-
nel audio inputs and outputs (typically labeled “R”). Use
white plugs to connect left-channel audio inputs and out-
puts (typically labeled “L”). And use yellow plugs to
connect composite video inputs and outputs.
• Before making any AV connections, read the manuals
supplied with your other AV components.
• Don’t connect the power cord until you’ve completed
and double-checked all AV connections.
Optical Digital Jacks
Analog audio
The AV receiver’s optical digital jack has shutter-type
cover that open when an optical plug is inserted and
close when it’s removed. Push plugs in all the way.
Left (white)
Right (red)
(Yellow)
Left (white)
Right (red)
(Yellow)
Composite video
Caution: To prevent shutter damage, hold the optical
plug straight when inserting and removing.
• Push plugs in all the way to make
good connections (loose connec-
tions can cause noise or malfunc-
tions).
Right!
• To prevent interference, keep
audio and video cables away from
power cords and speaker cables.
Wrong!
AV Cables & Jacks
Video
Cable
Jack
Description
Composite video is commonly used on TVs, VCRs,
and other video equipment. Use only dedicated
composite video cables.
Composite
video cable
V
Audio
Cable
Jack
Description
Offers the best sound quality and allows you to
enjoy surround sound (e.g., Dolby Digital, DTS).
The audio quality is the same as for coaxial.
OPTICAL
Optical digital
audio cable
Offers the best sound quality and allows you to
enjoy surround sound (e.g., Dolby Digital, DTS).
The audio quality is the same as for optical.
Coaxial digital
audio cable
COAXIAL
This cable carries analog audio. It’s the most com-
mon connection format for analog audio and can be
found on virtually all AV components.
L
Analog audio
cable (RCA)
R
This cable carries multichannel analog audio and is
typically used to connect DVD players with a 5.1-
channel analog audio output. Several standard ana-
log audio cables can be used instead of a multichan-
nel cable.
Multichannel
analog audio
cable (RCA)
Note: The AV receiver does not support SCART plugs.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting Both Audio & Video
By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you
can select both the audio and video simultaneously simply by selecting the appropriate input source on the AV receiver.
: Signal Flow
Video
Video
Audio
Audio
TV, projector,
etc.
DVD player, etc.
Speakers (see page 18 for connection infor-
mation)
Which Connections Should I Use?
The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format
you choose will depend on the formats supported by your other components. Use the following sections as a guide.
For video components, such as a DVD player, you must make two connections—one for audio, one for video.
Audio Connection Formats
Audio equipment can be connected to the AV receiver using the following audio connection formats: analog, optical,
coaxial, and multichannel.
When choosing a connection format, bear in mind that the AV receiver doesn’t convert between formats.
For example, audio signals connected to an OPTICAL or COAXIAL digital input are not output by the analog TAPE
OUT, so if you want to record from, for example, your CD player, in addition to connecting it to a digital input, you
must also connect it to the analog CD IN.
Audio Input/Output Diagram for Recording
CD player,
etc.
Optical
Optical
Analog
Analog
Multi-
channel
Coaxial
Coaxial
Output
IN
Multi-
channel
AV Receiver
OUT
Input
Analog
Cassette
recorder, etc.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a TV or Projector
Step 1:Video Connection
VIDEO
MONITOR
OUT
TV, projector,
etc.
VIDEO IN
Connection
HT-R330
Signal flow
TV
Composite video input
MONITOR OUT VIDEO
⇒
Step 2: Audio Connection
Choose a connection type (
,
, or ) that matches the TV, and then make the connection.
a
b
c
DIGITAL IN
b
c
Connect one or
the other
IN
a
COAXIAL
OPTICAL
L
R
VIDEO 2
COAXIAL
OUT
L
TV, projector,
etc.
R
OPTICAL
OUT
AUDIO
OUT
• With the basic connection, you can listen to or record audio from the TV.
a
• To enjoy Dolby and DTS listening modes, use connection or . (Use and or and for recording.)
b
c
a
b
a
c
Connection
HT-R330
Signal flow
TV
VIDEO 2 IN L/R
Analog audio L/R output
Digital coaxial output
Digital optical output
⇐
⇐
⇐
a
b
c
DIGITAL IN COAXIAL
DIGITAL IN OPTICAL
Hint!
If your TV has no audio outputs, connect your VCR to the AV receiver and use its tuner.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a DVD player
Step 1:Video Connection
VIDEO
DVD
IN
VIDEO OUT
DVD player
Connection
HT-R330
Signal flow
DVD player
DVD IN VIDEO
Composite video output
⇐
Step 2: Audio Connection
Choose a connection type (
,
,
, or ) that matches your DVD player, and then make the connection.
a
b
c
d
d
DIGITAL IN
b
FRONT
CENTER
SURROUND
COAXIAL
OPTICAL
Connect one
or the other
L
c
c
FRONT
R
L
SUB
WOOFER
DVD
R
DVD
FRONT
L
CENTER
SURR
a
COAXIAL
OUT
L
R
R
SUB
OPTICAL
OUT
AUDIO
OUT
WOOFER
DVD player
• With the basic connection, you can listen to or record audio from a DVD.
a
• To enjoy Dolby and DTS listening modes, use connection or . (Use and or and for recording.)
b
c
a
b
a
c
• To enjoy DVD-Audio or SACD playback from a compatible DVD player with an analog multichannel output,
use connection
.
d
Connection
HT-R330
Signal flow
DVD player
DVD IN FRONT
Analog audio L/R output
Digital coaxial output
Digital optical output
⇐
⇐
⇐
a
b
c
DIGITAL IN COAXIAL
DIGITAL IN OPTICAL
DVD IN FRONT, SURROUND,
CENTER, and SUBWOOFER
Analog multichannel output
⇐
d
• If your DVD player has main left and right outputs and multichannel left and right outputs, be sure to use the
main left and right outputs for connection
.
a
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a VCR or DVD Recorder for Playback
In addition to video playback, with this hookup example, you can use the VCR’s tuner to listen to the sound of your
favorite TV programs via the AV receiver. This is useful if the TV has no audio outputs.
Step 1:Video Connection
VIDEO
VIDEO 1
IN
VIDEO OUT
VCR,
DVD recorder
Connection
HT-R330
Signal flow
VCR/DVD recorder
VIDEO 1 IN VIDEO
Composite video output
⇐
Step 2: Audio Connection
Choose a connection type (
,
, or ), and then make the connection.
a
b
c
DIGITAL IN
b
COAXIAL
OPTICAL
IN
Connect one
or the other
a
L
c
R
VIDEO 1
COAXIAL
OUT
L
R
OPTICAL
OUT
AUDIO
OUT
VCR,
DVD recorder
• With the basic connection, you can listen to the VCR/DVD recorder.
a
• To enjoy Dolby and DTS listening modes, use connection or . (Use and or and to listen via
b
c
a
b
a
c
speaker set B.)
Connection
HT-R330
Signal flow
VCR/DVD recorder
VIDEO 1 IN L/R
Analog audio L/R output
Digital coaxial output
Digital optical output
⇐
⇐
⇐
a
b
c
DIGITAL IN COAXIAL
DIGITAL IN OPTICAL
26
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a VCR or DVD Recorder for Recording
Step 1: Make video connection
.
.
A
a
Step 2: Make audio connection
VIDEO
VIDEO 1
A
a
L
R
VIDEO 1
L
R
AUDIO
IN
VCR,
DVD recorder
VIDEO IN
Connection
HT-R330
Signal flow
VCR/DVD recorder
Composite video input
Audio L/R input
VIDEO 1 OUT VIDEO
VIDEO 1 OUT L/R
⇒
⇒
A
a
Connecting a Camcorder, Games Console, or Other Device
Step 1: Make video connection
.
.
A
a
Step 2: Make audio connection
VIDEO 3
IN
L
a
R
L
AUDIO
OUT
R
VIDEO 3
IN
A
VIDEO OUT
Camcorder, games console,
etc.
Connection
HT-R330
VIDEO 3 IN
Signal flow
Camcorder/console
Composite video output
Analog audio L/R output
⇐
⇐
A
a
VIDEO 3 IN L/R
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a Satellite, Cable, Set-top box, or Other Video Source
Step 1:Video Connection
VIDEO
VIDEO 2
IN
Satellite, cable,
set-top box, etc.
VIDEO OUT
Connection
HT-R330
Signal flow
Video source
VIDEO 2 IN VIDEO
Composite video output
⇐
Step 2: Audio Connection
Choose a connection type (
,
, or ) that matches the video source, and then make the connection.
a
b
c
b
DIGITAL IN
COAXIAL
Connect one
or the other
IN
a
L
OPTICAL
c
R
VIDEO 2
COAXIAL
OUT
L
R
OPTICAL
OUT
AUDIO
OUT
Satellite, cable,
set-top box, etc.
• With the basic connection, you can listen to or record audio from the video source.
a
• To enjoy Dolby and DTS listening modes, use connection or . (Use and or and for recording.)
b
c
a
b
a
c
Connection
HT-R330
Signal flow
Video source
VIDEO 2 IN L/R
Analog audio L/R output
Digital coaxial output
Digital optical output
⇐
⇐
⇐
a
b
c
DIGITAL IN COAXIAL
DIGITAL IN OPTICAL
28
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a CD Player or Turntable
■ CD Player, or Turntable with Built-in Phono Preamp
Step 1:
Choose a connection type (
,
, or ) that matches the CD player, or choose for a turntable with a built-in phono
a
b
c
a
preamp, and then make the connection.
IN
DIGITAL IN
b
L
L
R
R
COAXIAL
AUDIO
OUTPUT
CD
Connect one
or the other
c
OPTICAL
IN
L
a
R
CD
a
COAXIAL
OUT
L
R
Turntable (MM) with
built-in phono
preamp
OPTICAL
OUT
AUDIO
OUT
CD player
• With the basic connection, you can listen to or record audio from the CD player or turntable.
a
• To connect the CD player digitally, use connection or . (Use and or and for recording.)
b
c
a
b
a
c
Connection
HT-R330
Signal flow
CD or turntable
CD IN L/R
Analog audio L/R output
Digital coaxial output
Digital optical output
⇐
⇐
⇐
a
b
c
DIGITAL IN COAXIAL
DIGITAL IN OPTICAL
■ Turntable with no Phono Preamp Built-in
A phono preamp is necessary to connect a turntable that
doesn’t have a phono preamp built-in.
■ Turntable with an MC (Moving Coil) Cartridge
An MC head amp and phono preamp are necessary to
connect a turntable with an MC (Moving Coil) cartridge.
AUDIO
AUDIO
INPUT
AUDIO
OUTPUT
AUDIO
IN
OUTPUT
OUTPUT
IN
Phono preamp
L
L
L
L
L
L
R
R
R
R
R
R
Phono
preamp
CD
CD
MC head amp or
MC transformer
AUDIO
AUDIO
INPUT
OUTPUT
L
L
AUDIO
OUTPUT
AUDIO
INPUT
R
R
L
L
R
R
29
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
Step 1:
Choose a connection type (
,
, or ) that matches the recorder, and then make the connection.
a
b
c
DIGITAL IN
b
OUT
IN
a
COAXIAL
OPTICAL
L
Connect one
or the other
c
R
L
TAPE
L
COAXIAL
OUT
R
R
IN
OUT
OPTICAL
OUT
REC PLAY
Cassette recorder, CDR,
etc.
• With the basic connection, you can play and record with the recorder.
a
• To connect the recorder digitally for playback purposes, use connections and or and
.
a
b
a
c
Connection
a
HT-R330
Signal flow
Cassette/CDR/MD/DAT recorder
⇐
⇒
TAPE IN L/R
TAPE OUT L/R
Analog audio L/R output
Analog audio L/R input
DIGITAL IN COAXIAL
DIGITAL IN OPTICAL
Digital coaxial output
Digital optical output
⇐
⇐
b
c
30
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting Onkyo
Components
Step 1: Be sure that the Onkyo component is connected to the AV receiver with an analog audio cable (RCA).
Step 2: Make the connection.
With
(Remote Interactive) you can use the following special
functions:
Auto Power On/Standby
When you start playback on a component connected via
, if the AV receiver is in Standby, it will turn on and select
that component as the input source automatically. Similarly, when the AV receiver is set to Standby, all components
connected via will also enter Standby. This function will not work if a component’s power cord is connected to the
AV receiver’s AC OUTLET.
Direct Change
When playback is started on a component connected via
, the AV receiver automatically selects that component as
the input source. If the DVD player is connected to the AV receiver’s multichannel input, you must press the
[MULTI CH] button (see page 37) to listen to all channels because the Direct Change
IN FRONT jacks.
function selects only the DVD
Notes:
IN
• Use only
cables for
connections.
L
cables are supplied with Onkyo players (DVD,
CD, etc.).
R
CD
• Some components have two
jacks, you can
FRONT
connect either one to the AV receiver. The other is
REMOTE
CONTROL
L
for connecting additional
nents.
-compatible compo-
R
DVD
• Connect the AV receiver’s
jack to only Onkyo
components. Connecting to other manufacturer’s
components may cause them to malfunction.
e.g., CD player
e.g., DVD player
R
L
ANALOG
AUDIO OUT
• Some components may not support all
func-
tions. Refer to the manuals supplied with your
components.
R
L
ANALOG
AUDIO OUT
Connecting the Power Cord
Notes:
• Before connecting the power cord, connect all of your speakers and AV components.
• Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical
equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning On
STANDBY
ON
STANDBY
REMOTE MODE
STANDBY/ON
RECEIVER
DVD
ON
TAPE/AMP
STANDBY indicator
INPUT SELECTOR
RECEIVER
CD
1
2
3
V
1
V
2
V3
TUNING
/
PRESET
MASTER VOLUME
MD
4
5
6
STANDBY/ON
MULTI CH
DVD
ENTER
CDR
7
8
9
STANDBY
TAPE
TUNER
CD
RETURN
SETUP
A
SPEAKERS
PHONES
B
TONE
+
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
+
10
0
CLR
-- ---
/
DIMMER
SLEEP
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
CH
VOL
DISC
TOP MENU
SP A/B
MENU
MUTING
Turning On the AV Receiver
Press the [STANDBY/ON] button.
Alternatively, press the remote controller’s [RECEIVER] button followed
by the [ON] button.
1
Remote
controller
AV receiver
STANDBY/ON
The AV receiver comes on, the display lights up, and the STANDBY indicator goes off.
or
To turn the AV receiver off, press the [STANDBY/ON] button, or the remote control-
ler’s [STANDBY] button. The AV receiver will enter Standby mode. To prevent any
loud surprises the next time you turn on the AV receiver, always turn down the volume
before turning it off.
To ensure smooth operation, here’s a few easy steps to help you configure the AV receiver before you use it for the
very first time. These settings only need to be made once.
■ Have you connected a component to a digital audio input?
If you have, see “Assigning Digital Inputs to Input Sources” on
page 33.
COAXIAL
OPTICAL
■ Have you connected an Onkyo MD recorder or CD recorder
OUT
IN
to the TAPE IN/OUT jacks?
page 33.
TAPE
CD recorder / MD recorder
■ Do the speaker configuration—this is essential!
See “Speaker Configuration” on page 34.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup
Assigning Digital Inputs to Input
Sources
Changing the TAPE/MD/CDR Display
If you connect an
-compatible Onkyo MiniDisc
recorder or CD recorder to the TAPE IN/OUT jacks, for
to work properly, you must change this setting.
2, 3
This setting can only be changed on the AV receiver.
TUNING
/
PRESET
MASTER VOLUME
STANDBY/ON
ENTER
STANDBY
TUNING
/
PRESET
MASTER VOLUME
RETURN
SETUP
A
SPEAKERS
PHONES
B
+
STANDBY/ON
TONE
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
ENTER
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
STANDBY
RETURN
SETUP
A
SPEAKERS
PHONES
B
+
TONE
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
1
1, 2
To enjoy Dolby Digital and DTS, you must connect your
DVD player to the AV receiver by using a digital audio
connection (coaxial or optical).
With this function, you can assign digital inputs to input
sources. For example, if you connect your DVD player
to DIGITAL IN OPTICAL, you’ll need to assign that
input (OPT) to the DVD input source.
Press the [TAPE] input selector
button so that “TAPE” appears
on the display.
1
2
TAPE
You can change the assignments as follows.
Note:
Make sure you also set your digital sources to send out a
digital signals. Please refer to the digital sources’ man-
ual.
Press and hold down the [TAPE]
input selector button (about 3
seconds) to set the display.
Repeat this step to select TAPE, MD, or
CDR.
TAPE
Press the input selector button
for the source that you want to
1
DVD
VIDEO 1/VCR
VIDEO
2
assign.
(Digital inputs cannot be assigned to
the TUNER input source.)
VIDEO
3
TAPE
TUNER
CD
Press the [DIGITAL INPUT]
button.
The current assignment appears.
2
3
DIGITAL INPUT
Press the [DIGITAL INPUT] but-
ton repeatedly to select COAX,
OPT or “– – – –” (analog).
DIGITAL INPUT
33
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Use the Up and Down [ ]/[
buttons to select “1. Speaker
Config,” and then press the
[ENTER] button.
]
2
ON
STANDBY
REMOTE MODE
RECEIVER
DVD
1
TAPE/AMP
INPUT SELECTOR
CD
1
2
3
V
1
V
2
V3
MD
4
5
6
MULTI CH
DVD
CDR
7
8
9
TAPE
TUNER
CD
+
10
0
CLR
-- ---
/
DIMMER
SLEEP
CH
VOL
DISC
TOP MENU
SP A/B
MENU
While the Subwoofer setting is
selected, use the Left and Right
3
4
MUTING
[
]/[ ] buttons to select Yes or
No.
Yes: Select if a subwoofer is con-
ENTER
2–8
RETURN
1, 9
RETURN
SETUP
nected.
No: Select if no subwoofer is con-
nected.
LISTENING MODE
SURROUND
STEREO
AUDIO SUBTITLE RANDOM REPEAT
-
+
LEVEL
TEST TONE
DISPLAY
CH SEL
LEVEL
Use the Down [ ] button to
select “Front,” and then use the
Left and Right [ ]/[ ] buttons to
select Small or Large.
Small: Select if the front speakers are
small.
PLAY MODE
OR-EQ
L
NIGHT
CINE FLTR
-
RC 606S
Large: Select if the front speakers are
large.
Note:
• If the Subwoofer setting in step 3 is
set to No, this setting is fixed at Large
and does not appear.
Speaker Configuration
This section explains how to specify which speakers are
connected and their sizes.
Use the Down [ ] button to
select “Center,” and then use the
Left and Right [ ]/[ ] buttons to
select Small, Large, or None.
Small: Select if the center speaker is
small.
Large: Select if the center speaker is
large.
None: Select if no center speaker is
connected.
5
For speakers with a cone diameter
larger than 6-1/2 inches (16 cm),
specify Large. For those with a
smaller diameter, specify Small.
Cone diameter
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
1
Note:
• If the Front setting in step 4 is set to
Small, the Large option cannot be
selected.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Use the Down [ ] button to
6
select “Surround,” and then use
the Left and Right [ ]/[ ] but-
tons to select Small, Large, or
None.
Small: Select if the surround speak-
ers are small.
Large: Select if the surround speak-
ers are large.
None: Select if no surround speakers
are connected.
Note:
• If the Front setting in step 4 is set to
Small, the Large option cannot be
selected.
Press the [SETUP] button.
Setup closes.
7
TESTING THE SPEAKERS
To test that all of the speakers are working properly,
press the remote controller’s [TEST TONE] but-
ton. The test tone will be output by each speaker in
turn and the name of each speaker will appear on the
display. To turn off the test tone, press the [TEST
TONE] button again.
• If the test tone is not produced by a speaker, or it’s
produced by a speaker other than that shown on
the display, you may have wired the speakers
tions (see page 18).
• If the test tone is not produced by a speaker and its
name does not appear on the display, you may
have set the speaker settings incorrectly (see
page 34).
35
Download from Www.Somanuals.com. All Manuals Search And Download.
PlayingYour AV Components
Basic AV Receiver Operation
ON
STANDBY
REMOTE MODE
4
2
DISPLAY
RECEIVER
DVD
1
4
TAPE/AMP
INPUT SELECTOR
CD
1
2
3
1
2
TUNING
/
PRESET
MASTER VOLUME
V
1
V
2
V3
MD
STANDBY/ON
4
5
6
MULTI CH
DVD
ENTER
STANDBY
CDR
7
8
9
TAPE
TUNER
CD
RETURN
SETUP
A
SPEAKERS
PHONES
B
TONE
+
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
+
10
0
CLR
CLEAR
-- ---
/
DIMMER
SLEEP
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
CH
VOL
DISC
TOP MENU
SP A/B
MENU
MUTING
MULTI CH
1
ENTER
Remote
controller
Use the AV receiver’s input selector buttons to select the input source.
1
AV receiver
To select the input source with the remote controller, press the
[RECEIVER] button, and then use the INPUT SELECTOR buttons.
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1/VCR,
VIDEO 2, and VIDEO 3 input sources respectively.
CD
Use the SPEAKERS [A] and [B] buttons on the AV receiver or the [SP A/B]
button on the remote controller to select the speaker set that you want to
use.
2
Remote
controller
AV receiver
A
SPEAKERS
B
Pressing the remote controller’s [SPA/B] button cycles through the following settings:
Speaker Set A → Speaker Set A&B → Speaker Set B → Off.
The A and B speaker indicators show
whether each speaker set is on or off.
Note that when speaker set B is turned on,
speaker set A is reduced to 2.1-channel
playback.
Indicators
Start playback on the source component.
When you select DVD or another video component, on your TV you’ll need to select
the video input that’s connected to the AV receiver’s MONITOR OUT.
3
4
To adjust the volume, use the MASTER VOLUME control, or the remote
controller’s [VOL] button.
Remote
controller
AV receiver
MASTER VOLUME
The volume can be set to MIN, 1 through 79, or MAX. The AV receiver is designed for
home theater enjoyment and has a wide volume range for precise adjustment.
VOL
Select a suitable listening mode and enjoy!
See page 44.
5
36
Download from Www.Somanuals.com. All Manuals Search And Download.
PlayingYour AV Components—Continued
Displaying Source Information
ON
STANDBY
REMOTE MODE
You can display various information about the current
input source as follows.
RECEIVER
DVD
RECEIVER
TAPE/AMP
INPUT SELECTOR
CD
1
2
3
V
1
V
2
V3
Press the [RECEIVER] button,
and then press the [DISPLAY]
button repeatedly to cycle
through the available informa-
tion.
MD
4
5
6
MULTI CH
MULTI CH
DVD
CDR
7
8
9
TAPE
TUNER
CD
+
10
0
CLR
-- ---
/
DIMMER
SLEEP
CH
VOL
DISC
The following information can typically be displayed for
input sources.
LISTENING MODE
STEREO
SURROUND
AUDIO SUBTITLE RANDOM REPEAT
Input source &
volume
-
+
LEVEL
TEST TONE
DISPLAY
CH SEL
LEVEL
PLAY MODE
OR-EQ
L
NIGHT
CINE FLTR
DISPLAY
Signal format*
or sampling
frequency
-
RC 606S
Input source &
listening mode
displayed. If the input signal is PCM, the sampling fre-
quency is displayed. If the input signal is digital but not
PCM, the signal format is displayed. Information is dis-
played for about three seconds, then the previously dis-
played information reappears.
Using the Multichannel Input
The multichannel input is for connecting a component
with individual 5.1-channel analog audio output jacks,
such as a DVD player or MPEG decoder. See page 25 for
hookup information.
Interpreting Surround Channel Information
Press the [RECEIVER] button fol-
lowed by the [MULTI CH] button
so that MULTI CH indicator
A
B
C
appears on the display.
Audio from the multichannel input will
now be used for the DVD input source.
A: The number of front channels (front left, front right,
and center).
MULTI CH indicator
B: The number of surround channels (surround left and
surround right). If there’s surround back channel
information, this number will be 3.
C: LFE channel for subwoofer (1 means yes).
Note:
• While the multichannel input is selected, the Speaker
Configuration settings on page 34 are ignored, and
signals from the multichannel input are fed to the front
left, front right, center, surround left, and surround
right speakers and subwoofer regardless of those set-
tings.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
Listening to the Radio
Tuning into Radio Stations
■ Auto Tuning Mode
TUNING MODE
TUNING
Press the [TUNING MODE] button
1 TUNING MODE
so that the AUTO indicator
appears on the display.
TUNING
/
PRESET
MASTER VOLUME
STANDBY/ON
ENTER
STANDBY
RETURN
SETUP
A
SPEAKERS
PHONES
B
+
TONE
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
Press the TUNING Up or Down
2
TUNING
/
PRESET
[
]/[ ] button.
Searching stops when a station is
found.
TUNER
ENTER
With the built-in tuner, you can enjoy AM and FM radio
stations. You can store your favorite stations as presets
for quick selection.
When tuned into a station, the TUNED indicator
appears. When tuned into a stereo FM station, the FM
STEREO indicator appears on the display, as shown.
Use the [TUNER] input selector
button to select either AM or FM.
In this example, FM has been selected.
TUNER
1
TUNED AUTO
Band
Frequency
(Actual display depends on country.)
FM STEREO
■ Manual Tuning Mode
AM Frequency Step Setup
(not North America and Europe)
Press the [TUNING MODE] button
so that the AUTO indicator disap-
pears from the display.
1
TUNING MODE
Here you can specify the AM frequency step used in
your area. When this setting is changed, all radio presets
are deleted.
Press and hold theTUNING Up or
Down [ ]/[ ] button.
The frequency stops changing when
you release the button.
Press the buttons repeatedly to change
the frequency one step at a time.
2
TUNING
/
PRESET
Press the [SETUP] button and
use the Up and Down [ ]/[
1
]
ENTER
buttons to select “0. Hardware
Setup,” and then press [ENTER].
Use the Up and Down [ ]/[
buttons to select “AM Freq,” and
then use the Left and Right
]
2
TheAmerican model changes FM frequency in 0.2 MHz
steps, 10 kHz steps for AM. For other models it’s
0.05 MHz steps for FM and 9 kHz steps for AM.
In Manual Tuning mode, FM stations will be in mono.
[
]/[ ] buttons to select:
10 kHz: Select if 10 kHz steps are
used in your area.
9 kHz: Select if 9 kHz steps are used
in your area.
Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Press the [SETUP] button.
Setup closes.
3
Note:
• This procedure can also be performed on the remote
controller by using its [SETUP] button, arrow buttons,
and [ENTER] button.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner—Continued
Presetting Radio Stations
Deleting Presets
2, 4
2
3
TUNING
/
PRESET
TUNING
/
PRESET
MASTER VOLUME
MASTER VOLUME
STANDBY/ON
STANDBY/ON
ENTER
ENTER
STANDBY
STANDBY
RETURN
SETUP
A
SPEAKERS
PHONES
B
+
RETURN
SETUP
TONE
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
A
SPEAKERS
PHONES
B
TONE
+
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
CLEAR
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
You can store up to 30 of your favorite radio stations as
presets.
Select the preset that you want to
delete.
See the previous section.
1
2
Tune into the station that you
want to store as a preset.
1
While holding down the [MEM-
ORY] button, press the
[TUNING MODE] button.
Press the [MEMORY] button.
The MEMORY indicator appears and
MEMORY TUNING MODE
CLEAR
2
MEMORY
The selected preset is deleted and its
number disappears from the display.
the preset number flashes.
While the MEMORY indicator is
Displaying Radio Information
3
TUNING
/
PRESET
displayed (about 8 seconds), use
the PRESET [ ]/[ ] buttons to
select a preset from 1 through 30.
In this example, preset #3 is selected.
1
ENTER
TUNING
/
PRESET
MASTER VOLUME
STANDBY/ON
ENTER
STANDBY
RETURN
SETUP
A
SPEAKERS
PHONES
B
+
TONE
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
Press the [MEMORY] button
again to store the station.
The station is stored and the preset
number stops flashing.
Repeat this procedure for all your
favorite radio stations.
4
MEMORY
Press the [DISPLAY] button
repeatedly to cycle through the
available information.
DISPLAY
1
Selecting Preset Stations
Band, preset # &
frequency
1
TUNING
/
PRESET
MASTER VOLUME
Listening mode
STANDBY/ON
ENTER
STANDBY
RETURN
SETUP
A
SPEAKERS
PHONES
B
+
TONE
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
TUNING
/
PRESET
Use the PRESET [ ]/[ ] but-
tons, or the remote controller’s
CH [+/–] button to select a preset.
1
ENTER
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner—Continued
Using RDS (European models only)
Program Types Used in Europe (PTY)
RDS only works with European models and only in areas
where RDS broadcasts are available. When tuned into an
RDS station, the RDS indicator appears.
Type
Display
NONE
NEWS
Description
None
No program type.
News
reports
Reports on current events and
happenings.
RDS indicator
Current
affairs
AFFAIRS Topical reporting of current
affairs, often with a wider
range of topics than news
reports.
Information INFO
General information such as
weather forecasts, consumer
affairs, medical help, etc.
■ What is RDS?
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. It was developed
by the European Broadcasting Union (EBU) and is avail-
able in most European countries. Many FM stations use
it these days. In addition to displaying text information,
RDS can also help you find radio stations by type (e.g.,
news, sport, rock, etc.).
Sport
SPORT
Live sports action, sports
news, and interviews.
Education EDUCATE Formal educational programs.
Drama
Culture
DRAMA
Radio plays and serials.
CULTURE Cultural programs (including
religious affairs).
The AV receiver supports four types of RDS informa-
tion:
Scienceand SCIENCE Programs about the natural
technology
sciences and technology.
PS (Program Service)
Varied
VARIED
Speech-based programs not
covered by the above catego-
ries (e.g., quizzes, panel
games, and comedy).
When tuned to an RDS station that’s broadcasting PS
information, the station’s name appears. When you press
the [DISPLAY] button, the frequency is displayed for
three seconds.
Pop music POP M
Popular commercial music,
usually from past or present
sales charts (e.g., Top 40).
RT (Radio Text)
When tuned to an RDS station that’s broadcasting RT
text information, that information is shown on the dis-
play (see page 41).
Rock music ROCK M Popular music with an alterna-
tive appeal, often not appear-
PTY (Program Type)
ing on sales charts.
You can also search for radio stations by type (see
page 41).
Middle of
the road
music
M.O.R.M Easy listening music (as
opposed to Pop, Rock, or
Classical).
TP (Traffic Program)
You can also search for TP radio stations (see page 41).
Light clas- LIGHT M Classical music for general
sics
rather than specialist appreci-
ation.
Notes:
• In some cases, the text characters displayed on the AV
receiver may not be identical to those broadcast by the
radio station. Also, unexpected characters may be dis-
played when unsupported characters are received.
This is not a malfunction.
Serious
classics
CLASSICS Performances of major
orchestral works, sympho-
nies, chamber music, etc.
(including the Grand Opera).
Other music OTHER M Music styles not covered by
the above categories (e.g.,
• If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
Jazz, Rhythm & Blues, Folk,
Country, and Reggae).
Alarm
ALARM
When an RDS station is mak-
ing an emergency broadcast,
ALARM will flash on the dis-
play.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner—Continued
Displaying Radio Text (RT)
To start the search, press
[ENTER].
The AV receiver searches until it finds a
station of the type you specified, at
which point it stops briefly before con-
tinuing with the search.
4
5
ENTER
1
TUNING
/
PRESET
MASTER VOLUME
STANDBY/ON
ENTER
STANDBY
RETURN
SETUP
A
SPEAKERS
PHONES
B
+
TONE
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
When a station you want to listen
to is found, press [ENTER].
If no stations are found, the message
“Not Found” appears.
ENTER
When tuned to an RDS station that’s broadcasting RT
text information, that information can be displayed.
Press the [RT/PTY/TP] button
once.
1
Listening to Traffic News (TP)
RT/PTY/TP
The RT information scrolls across the
display.
2
3
TUNING
/
PRESET
MASTER VOLUME
STANDBY/ON
ENTER
Notes:
STANDBY
• The message “Waiting” may appear while the AV
receiver waits for RT information.
RETURN
SETUP
A
SPEAKERS
PHONES
B
+
TONE
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
• If the message “No Text Data” appears on the display,
no RT information is available.
1
You can search for TP radio stations.
Finding Stations by Type (PTY)
Use the [TUNER] input selector
button to select FM.
TUNER
1
2
3–5
TUNING
/
PRESET
MASTER VOLUME
STANDBY/ON
ENTER
STANDBY
RETURN
SETUP
A
SPEAKERS
PHONES
B
+
TONE
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
Press the [RT/PTY/TP] button
three times.
RT/PTY/TP
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
2
If the current radio station is broadcast-
ing TP (Traffic Program), “[TP]” will
appear on the display, and traffic news
will be heard as and when it’s broad-
cast. If “TP” without square brackets
appears, this means that the station is
not broadcasting TP.
1
You can search for radio stations by type.
Use the [TUNER] input selector
button to select FM.
TUNER
1
2
3
To locate a station that is broad-
casting TP, press [ENTER].
The AV receiver searches until it finds a
station that’s broadcasting TP.
If no stations are found, the message
“Not Found” appears.
3
ENTER
Press the [RT/PTY/TP] button
twice.
The current program type appears on
the display.
RT/PTY/TP
Use the PRESET [ ]/[ ] buttons
to select the type of program you
want.
TUNING
/
PRESET
ENTER
See the table on page 40.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Functions
This chapter explains functions that can be used with any
input source.
Setting the Display Brightness
With this function, you can adjust the brightness of the
display.
ON
STANDBY
REMOTE MODE
Press
[RECEIVER]
first
RECEIVER
DVD
TAPE/AMP
Press the remote controller’s
[DIMMER] button repeatedly to
select: dim, dimmer, or normal
brightness.
INPUT SELECTOR
CD
1
2
3
V1
V2
V3
MD
4
5
6
MULTI CH
DVD
CDR
7
8
9
TAPE
TUNER
CD
Alternatively, you can use the [DIM-
MER] button on the AV receiver (not
European models).
+
10
0
CLR
DIMMER
SLEEP
-- ---
/
DIMMER
SLEEP
CH
VOL
DISC
TOP MENU
SP A/B
MENU
MUTING
MUTING
Adjusting the Bass & Treble
ENTER
You can adjust the bass or treble for the front speakers
except when the Direct listening mode is selected.
RETURN
SETUP
Press the AV receiver’s [TONE]
button repeatedly to select either
Bass or Treble.
TONE
1
LISTENING MODE
STEREO
SURROUND
AUDIO SUBTITLE RANDOM REPEAT
-
+
LEVEL
TEST TONE
DISPLAY
CH SEL
LEVEL
CH SEL
LEVEL – +
PLAY MODE
OR-EQ
L
NIGHT
CINE FLTR
Use the TONE [–]/[+] buttons to
adjust.
+
2
-
RC 606S
■ Bass
You can boost or cut low-frequency sounds output by the
front speakers from –10 dB to +10 dB in 2 dB steps.
TONE, –, +
TUNING
/
PRESET
MASTER VOLUME
STANDBY/ON
■ Treble
ENTER
STANDBY
You can boost or cut high-frequency sounds output by
the front speakers from –10 dB to +10 dB in 2 dB steps.
RETURN
SETUP
A
SPEAKERS
PHONES
B
TONE
+
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
DIMMER
MEMORY TUNING MODE
CLEAR
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
Note:
• To bypass the bass and treble tone circuits, select the
Direct listening mode.
PHONES
DIMMER
Muting the AV Receiver
With this function, you can temporarily mute the output
of the AV receiver.
Using the OptiResponse Equalizer
When using the HT-R330 with the speakers included in
the HTP-330 HomeTheater Speaker Package, by turning
on the OptiResponse equalizer, you can enjoy a powerful
sound with movies or music.
Press the remote controller’s
[MUTING] button.
The output is muted
and the MUTING
indicator flashes on
the display, as shown.
Press the [OR-EQ] button to turn
the OptiResponse equalizer on
or off.
OR-EQ
To unmute the AV receiver, press the remote control-
ler’s [MUTING] button again, or adjust the volume. The
output is unmuted and the MUTING indicator goes off.
Muting is cancelled when the AV receiver is set to
Standby.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Functions—Continued
Using the Sleep Timer
Adjusting Speaker Levels
With the sleep timer, you can set the AV receiver so that
it automatically turns off after a set period.
You can adjust the level of each speaker in speaker set A
while listening to an input source. These temporary
adjustments are cancelled when the AV receiver is set to
Standby.
Press the remote controller’s
[SLEEP] button repeatedly to
select the required sleep time.
You can set the sleep time from 90 to 10
minutes in 10 minute steps.
Use the remote controller’s
1
[CH SEL] button to select each
speaker, and use the [LEVEL–]
and [LEVEL+] buttons to adjust
the volume.
The SLEEP indicator appears on the
display when the sleep timer has been
set, as shown. The specified sleep time
appears on the display for about five
seconds, then the previous display
reappears.
You can adjust the volume of each
speaker from –12 dB to +12 dB
(–15 dB to +12 dB for the subwoofer).
SLEEP indicator
Notes:
• You cannot use this function while the AV receiver is
muted.
To cancel the sleep timer, press the [SLEEP] button
repeatedly until the SLEEP indicator disappears.
• Speakers that are set to No or None in the Speaker
Configuration cannot be adjusted.
To check the remaining sleep time, press the [SLEEP]
button. Note that if you press the [SLEEP] button while
the sleep time is being displayed, you’ll shorten the sleep
time by 10 minutes.
■ Speaker Set B
While speaker set B is on, you can also adjust the levels
of the left and right speakers in speaker set B, from
–12 dB to +12 dB.
• These settings are stored when the AV receiver is set
to Standby.
Using Headphones
You can connect a pair of stereo headphones (1/4-inch
phone plug) to the AV receiver’s PHONES jack for pri-
vate listening, as shown.
• While speaker set B is on, you can adjust the levels of
the left and rigt speakers in speaker setA’s and the sub-
woofer.
■ Headphones
STANDBY/ON
While a pair of headphones is connected, you can adjust
the volume of the left and right channels individually,
from –12 dB to +12 dB each.
PHONES
• These settings are stored when the AV receiver is set
to Standby.
Notes:
• Always turn down the volume before connecting your
headphones.
■ Multichannel DVD Input
• Speaker sets A and B are turned off while the head-
phones plug is inserted in the PHONES jack.
While the multichannel DVD input is selected, you can
adjust the level of each 5.1 channel input individually,
woofer.)
• These settings are stored when the AV receiver is set
to Standby.
• When you connect a pair of headphones, the listening
mode is set to Stereo, unless it’s already set to Mono,
Stereo, or Direct.
• When the multichannel DVD input is selected, only
the front left and front right channels can be heard in
the headphones.
• Individual speaker levels can also be adjusted in
“3. MultiLevel Setup” (see page 52).
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes
Selecting with the Remote Controller
Selecting Listening Modes
See “About the Listening Modes” on page 46 for
detailed information about the listening modes.
TOP MENU
SP A/B
MUTING
• The Dolby Digital and DTS listening modes
can only be selected if your DVD player is
connected to the AV receiver with a digital
audio connection (coaxial or optical).
ENTER
RETURN
SETUP
• Listening mode availability depends on the
format of the current input signal.
• While a pair of headphones is connected, or
speaker B is on, you can select only the
Mono, Direct, or Stereo listening mode.
SURROUND
STEREO
LISTENING MODE
STEREO
SURROUND
,
AUDIO SUBTITLE RANDOM REPEAT
-
+
LEVEL
TEST TONE
DISPLAY
CH SEL
LEVEL
PLAY MODE
OR-EQ
L
NIGHT
CINE FLTR
-
RC 606S
Selecting on the AV receiver
TUNING
/
PRESET
MASTER VOLUME
STANDBY/ON
ENTER
STANDBY
RETURN
SETUP
A
SPEAKERS
PHONES
B
+
TONE
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
■ [STEREO] button
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
This button selects the Stereo listening mode.
■ [SURROUND] button
This button selects the Dolby Digital and DTS listen-
ing modes.
STEREO
LISTENING MODE
■ LISTENING MODE [ ]/[ ] buttons
Pressing these buttons repeatedly cycles through all
of the listening modes that can be used with the cur-
rent input source.
■ [STEREO] button
This button selects the Stereo listening mode.
■ LISTENING MODE [ ]/[ ] buttons
Pressing these buttons repeatedly cycles through all
of the listening modes that can be used with the cur-
rent input source.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
The following table lists all the listening modes and shows which modes can be selected for each input signal format.
DTS/DTS 96/24*2
Dolby D
Analog,
PCM*1
Input signal format
Multich
DTS-ES
2/0
2/0
*/2
1/0,1+1 Other
3/2.1
(Stereo)
(Stereo)
Discrete Matrix
CD,TV,VHS,
MD,
Source
turntable,
radio,
DVD, DTV, etc.
DVD, CD, etc.
DVD
cassette,
DTV, etc.
Listening mode
Direct
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Stereo
Mono
Multich
✔
PLII Movie/Music/Game
Neo:6 Cinema
Neo:6 Music *3
✔
✔
✔
Dolby D
✔
✔
✔
✔
DTS
✔
✔
✔
✔
Mono Movie
Orchestra
Unplugged
Studio-Mix
TV Logic
Onkyo
Original
DSP
*3
✔
✔
✔
✔
All Ch Stereo
Full Mono
*1. In the Direct listening modes, PCM signals at 32 kHz, 44.1 kHz, and 48 kHz are processed at 64 kHz, 88.2 kHz, and 96 kHz
respectively. 96 kHz signals are processed at 48 kHz for all listening modes other than Direct, and Stereo.
*2. DTS 96/24 is always processed as DTS.
*3. Available only when Surround speakers are connected.
Tip: You can check the format of the digital input signal on page 37, “Displaying Source Information.”
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
player in order to enjoy DTS material. Use this mode
with DVDs and CDs that bear the DTS logo.
About the Listening Modes
With its built-in surround-sound decoders and DSP pro-
grams, the AV receiver can transform your home listen-
ing room into a movie theater or concert hall.
Neo:6
This mode provides 5.1-channel playback from 2-chan-
nel sources. It offers five full-bandwidth channels with
excellent separation. There are two modes of operation:
Cinema mode for movies, and Music mode for listening
to music.
The AV receiver’s surround indicators show which
speakers are active in each listening mode.
Front left
Center
Front right
Cinema mode simulates the realistic sense of movement
that you get with 5.1-channel surround sound sources.
Use this mode with videos, DVDs, and TV shows that
feature stereo sound.
Music mode uses the surround channels to simulate a
natural sound field that cannot be produced with conven-
tional stereo. Use this mode with stereo material such as
music CDs.
Subwoofer
Surround
left
Surround
right
Direct
The selected input source is output directly with minimal
processing for a pure sound.
Stereo
The selected input source is processed as a stereo signal
and output by the front left and right speakers and the
subwoofer.
Onkyo Original DSP Modes
Mono Movie
This mode is suitable for use with old movies and other
mono sound sources. The center speaker outputs the
sound as it is, while reverb is applied to the sound output
by the other speakers, giving presence to even mono
material.
Mono
Use this mode when watching an old movie with a mono
soundtrack, or to select multilingual soundtracks
recorded in the left and right channels of some movies.
It can also be used when playing a DVD or other source
with multiplexed audio, such as a karaoke DVD.
Orchestra
Suitable for classical or operatic music. The surround
channels are emphasized in order to widen the stereo
image. In addition, it simulates the natural reverberation
of a large hall.
Dolby Pro Logic II Movie
Use this mode with DVDs and vid-
eos that bear the Dolby Surround
logo or TV shows that feature Dolby Surround. You can
also use this mode with stereo movies or TV shows and
the AV receiver will create a 5.1 surround mix from the
2-channel stereo.
Unplugged
Suitable for acoustic instrument sounds, vocals, and jazz
music. By emphasizing the front stereo image, it simu-
lates the stage-front experience.
Dolby Pro Logic II Music
Use this mode to add 5.1 surround to stereo sources such
as music CDs and DVDs.
Studio-Mix
Suitable for rock and pop music. Listening to music in
this mode creates a lively sound field with a powerful
acoustic image, like being at a club or rock concert.
Dolby Pro Logic II Game
Use this mode when playing game discs.
TV Logic
Dolby Digital
Adds realistic acoustics to TV shows produced in a TV
studio. In addition, it adds surround effects to the entire
sound and adds clarity to voices.
With this format you can experience the
same superb sound that you get at a movie
theater or concert hall. Use this mode with DVDs that
bear the Dolby Digital logo.
All Ch Stereo
Ideal for background music. The front, surround, and
surround back channels create a stereo image that fills
the entire listening area.
DTS
This digital surround format offers a sur-
round sound experience with exceptional
fidelity. It uses compressed digital audio
data, with six discrete channels (5.1), and the
ability to handle large amounts of audio data while
remaining faithful to the original. DTS provides very
high-quality sound.You’ll need a DTS compatible DVD
Full Mono
In this mode, all speakers output mono audio, so the
music sounds the same regardless of where you are.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Listening Modes
Use the Left and Right [ ]/[
buttons to change the settings.
Press the Down [ ] button to
select the next setting.
]
3
ON
STANDBY
REMOTE MODE
RECEIVER
DVD
CD
RECEIVER
TAPE/AMP
INPUT SELECTOR
1
2
3
V
1
V
2
V3
MD
4
5
6
MULTI CH
DVD
CDR
7
8
9
TAPE
TUNER
CD
+
10
0
CLR
-- ---
/
DIMMER
SLEEP
CH
VOL
DISC
TOP MENU
SP A/B
MENU
Repeat step 3 to complete all set-
tings.
4
5
MUTING
ENTER
ENTER
Press the [SETUP] button.
Setup closes.
SETUP
RETURN
SETUP
LISTENING MODE
STEREO
SURROUND
The Audio Adjust functions are explained below.
AUDIO SUBTITLE RANDOM REPEAT
-
+
LEVEL
TEST TONE
DISPLAY
CH SEL
LEVEL
PLAY MODE
OR-EQ
Input Channel Settings
L
NIGHT
CINE FLTR
CINE FLTR
L NIGHT
■ Multiplex
-
This setting determines which channel is output from a
stereo multiplex source. Use it to select audio channels
or languages with multiplex sources, multilingual TV
broadcasts, and so on.
RC 606S
Main: The main channel is output (default).
Sub: The sub channel is output.
M/S: Both the main and sub channels are output.
Using the Audio Adjust Functions
These functions only work with speaker set A.
Audio Adjust provides various functions for adjusting
the sound.
■ Mono (2ch)
This setting determines which channel is output when
the Mono listening mode is used with a stereo source.
L+R: Both the left and right channels are output
(default).
Press the [RECEIVER] button fol-
1
lowed by the [SETUP] button.
L: Only the left channel is output.
R: Only the right channel is output.
Use the Up and Down [ ]/[
buttons to select “4. Audio
Adjust,” and then press the
[ENTER] button.
]
2
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Listening Modes—Continued
PL II Music Mode Settings
Using the Late Night Function
(Dolby Digital only)
These settings apply to only 2-channel (stereo) sources.
With the Late Night function, you can reduce the
dynamic range of Dolby Digital material so that you can
still hear quiet parts even when listening at low volume
levels—ideal for watching movies late at night when you
don’t want to disturb anyone.
■ Panorama
With this function, you can broaden the width of the
front stereo image when using the Pro Logic II Music
listening mode.
On: Panorama function on.
Off: Panorama function off (default).
Press the [RECEIVER] button,
1
and then press the [L NIGHT] but-
ton repeatedly to select:
Off: Late Night function off.
Low: Small reduction in dynamic
range.
■ Dimension
With this setting, you can move the sound field forward
or backward when using the Pro Logic II Music listening
mode. The default setting is 3. Higher settings move the
sound field forward. Lower settings move it backward.
If the stereo image feels too wide, or there’s too much
surround sound, move the sound field forward to
improve the balance. Conversely, if the stereo image
feels like it’s in mono, or there’s not enough surround
sound, move it backward.
High: Big reduction in dynamic
range.
Notes:
• The effect of the Late Night function depends on the
Dolby Digital material that you are playing, and with
some material there will be little or no effect.
■ Center Width
With this function, you can adjust the width of the sound
from the center speaker when using the Pro Logic II
Music listening mode normally. If you’re using a center
speaker, the center channel sound is output by only the
center speaker. (If you’re not using a center speaker, the
center channel sound will be distributed to the front left
and right speakers to create a phantom center). This set-
ting controls the front left, right, and center mix, allow-
ing you to adjust the weight of the center channel sound.
It can be adjusted from 0 to 7 (default is 3).
• The Late Night function is set to Off when the AV
receiver is set to Standby.
Using the CinemaFILTER
With the CinemaFILTER, you can soften overly bright
movie soundtracks, which are typically mixed for repro-
duction in a movie theater.
CinemaFILTER can be used with the following listening
modes: Dolby Digital, Dolby Pro Logic II Movie, DTS,
and DTS Neo:6 Cinema.
DTS Neo:6 Music Mode Setting
■ Center Image
The DTS Neo:6 Music listening mode creates 5-channel
surround sound from 2-channel (stereo) sources. With
this setting, you can specify by how much the front left
and right channel output is attenuated in order to create
the center channel. It can be adjusted from 0 to 5 (default
is 3). This setting is unavailable if no surround speakers
are connected.
Press the [RECEIVER] button,
1
and then press the [CINE FLTR]
button repeatedly to select:
On: CinemaFILTER on.
Off: CinemaFILTER off.
When set to 0, the front left and right channel output is
attenuated by half (–6 dB), giving the impression that the
sound is located centrally. This setting works well when
the listening position is considerably off center. When
set to 5, the front left and right channels are not attenu-
ated, maintaining the original stereo balance.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
This chapter explains how to record the selected input
source to an AV component with recording capability,
and how to record audio and video from two different
sources.
Recording from Different AV Sources
With this function, you can record audio and video from
different sources, allowing you to overdub audio onto
your video recordings. This function takes advantage of
the fact that when an audio-only input source (i.e.,
TAPE, TUNER, or CD) is selected, the video input
source remains unchanged. For example, if you first
select the VIDEO 3 input source, followed by the CD
input source, you can watch the video from theVIDEO 3
input and listen to the audio from the CD input.
Recording the Input Source
You can record only to AV components that are con-
nected to the TAPE OUT or VIDEO 1 OUT jacks.
See pages 22–31 for information on connecting yourAV
components to the AV receiver.
In the following example, audio from the CD player con-
nected to the CD IN jacks, and video from the camcorder
connected to the VIDEO 3 IN jack are recorded by the
VCR, which is connected to the VIDEO 1 OUT jacks.
Use the input selector buttons to
select the AV component that
you want to record.
Audio signals from the selected input
source are output by theVIDEO 1 OUT
and TAPE OUT jacks.
1
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
You can listen to the source while
recording. The AV receiver’s VOL-
UME control has no effect on record-
ing.
Camcorder
Remote
controller
video signal
audio signal
Start recording on the AV compo-
nent connected to theTAPE OUT
or VIDEO 1 OUT jacks.
2
3
Start playback on the source AV
component.
Notes:
CD player
VCR
• You cannot record from AV components that are con-
nected to the digital inputs. You must use analog con-
nections.
1. Prepare the camcorder and CD player
• The surround effects produced by the surround and
DSP listening modes cannot be recorded.
for playback.
2. Prepare the VCR for recording.
• You cannot record from an AV component that is con-
nected to the multichannel input.
3. Press the [VIDEO 3] input selector but-
ton.
• If you select another input source while recording, that
input source will be recorded instead.
4. Press the [CD] input selector button.
This selects the CD player as the audio source, but
leaves the camcorder as the video source.
5. Start recording on the VCR and start
playback on the camcorder and CD
player.
The video from the camcorder and the audio from
the CD player are recorded by the VCR.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup
Advanced Speaker Settings
Speaker cone
diameter
Crossover
frequency
The advanced speaker settings cannot be
changed while headphones are connected,
Speaker set B is on, or the multichannel input
is being used.
Over 8 in.
(20 cm)
60Hz
80Hz
6-1/2 to 8 in.
(16–20 cm)
5-1/4 to 6-1/2 in.
(13–16 cm)
100Hz
120Hz
150Hz
Crossover Frequency
3-1/2 to 5-1/4 in.
(9–13 cm)
To get the best bass performance from your speaker sys-
tem, you need to set the crossover frequency according
to the size and frequency response of your subwoofer
and other speakers (front, center, and surround).
Under 3-1/2 in.
(9 cm)
Continue with step 4 of the “Double
Bass” setting.
Press the [RECEIVER] button fol-
1
lowed by the [SETUP] button on
the remote controller.
Note:
• For a more accurate setting, listen to some music that
you know well and choose a higher crossover fre-
quency if you think there’s not enough sound coming
from the subwoofer; a lower setting if you think
there’s too much.
Use the Up and Down [ ]/[
buttons to select “1. Speaker
Config,” and then press the
[ENTER] button.
]
2
3
Double Bass
put by feeding bass sounds from the front left and right
channels to the subwoofer. This function can be set only
if the Subwoofer setting (step 3) is set to Yes, and the
Front setting (step 4) is set to Large in the Speaker Con-
figuration on page 34.
Use the Down [ ] button to
select “Double Bass,” and then
4
Use the Down [ ] button to
select “Crossover,” and then use
the Left and Right [ ]/[ ] but-
tons to select a crossover fre-
quency.
Choose a crossover frequency suitable
for your setup.
use the Left and Right [ ]/[
buttons to select:
]
On: Double Bass function on.
Bass from the front left and
right channels is also fed to
the subwoofer (default).
If you’re using a subwoofer, choose a
crossover frequency based on the diam-
eter of your front speakers.
Off: Double Bass function off.
If you’re not using a subwoofer, use
the diameter of the first speaker that
you specified as Small in steps 4
through 7 in the “Speaker configura-
tion” setting (see page 34).
Press the [SETUP] button.
Setup closes.
5
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Notes:
Speaker Distance
• The Center and Subwoofer distances can be set up to
5 ft. (1.5 m) more or less than the Front distance. For
example, if the Front distance is set to 20 ft. (6 m), the
Center and Subwoofer distances can be set between 15
and 25 ft. (4.5 and 7.5 m).
To get the best from surround sound, it’s important that
the sound from each speaker reaches the listener at the
same time. To achieve this, you need to specify the dis-
tance from each speaker to the listening position.
• The Surround distances can be set up to 5 ft. (1.5 m)
more or 15 ft. (4.5 m) less than the Front distance. For
example, if the Front distance is set to 20 ft. (6 m), the
SurrRight and Surr Left distances can be set between
5 and 25 ft. (1.5 and 7.5 m).
Measure and make a note of the
distance from each speaker to
the listening position.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button on
the remote controller.
2
Speaker Levels
With this function, you can adjust the volume of each
speaker so that all speakers can be heard equally at the
listening position.
Use the Up and Down [ ]/[
buttons to select “2. Sp Dis-
tance,” and then press the
[ENTER] button.
]
3
Speaker levels cannot be adjusted while the
AV receiver is muted.
Press the [RECEIVER] button fol-
lowed by the [SETUP] button on
the remote controller.
1
While“Unit”is displayed, use the
Left and Right [ ]/[ ] buttons to
select “feet” or “meters”.
4
5
Use the Up and Down [ ]/[
]
2
3
feet: Distances in feet. Can be set
from 1 to 30 feet in 1-foot
steps.
buttons to select “3. Level Cal,”
and then press the [ENTER] but-
ton.
A pink noise test tone is output by the
front left speaker.
meters: Distances in meters. Can be
set from 0.3 to 9 meters in
0.3-meter steps.
Use the Down [ ] button to
select “Front,” and use the Left
and Right [ ]/[ ] buttons to
specify the distance for the“front
speakers,” then press the Down
Turn up the volume so that you
can hear the test tone suffi-
ciently.
While each speaker outputs the test
tone, its name appears on the display, as
shown.
[
] button to select the next
speaker.
Repeat step 5 for all speakers.
6
7
Note:
Speakers that you set to No or None in
the Speaker Configuration (page 34)
cannot be selected.
Press the [SETUP] button.
Setup closes.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Use the Left and Right [ ]/[
buttons to adjust the speaker
]
Digital Input Signal Formats
4
The following table shows the display indicators for each
supported digital signal format.
level, and use the Down [ ] but-
ton to select the next speaker.
The level can be adjusted from –12 to
+12 dB in 1 dB steps (–15 to +12 dB
for the subwoofer).
Format
Dolby Digital
DTS
Display
PCM
PCM
Normally, the AV receiver detects the signal format auto-
matically. However, if you experience either of the fol-
lowing issues when playing PCM or DTS material, you
can manually set the signal format to PCM or DTS:
• If the beginnings of tracks from a PCM source are cut
off, try setting the format to PCM.
Repeat step 4 so that the level of
the test tone from each speaker
is the same.
Speakers that you set to No or None in
the Speaker Configuration (page 34) do
not output the test tone.
5
• If noise is produced when fast forwarding or reversing
a DTS CD, try setting the format to DTS.
Press the [SETUP] button.
Setup closes.
6
TUNING
/
PRESET
MASTER VOLUME
Don’t forget to turn down the volume if
you turned it up while setting the levels.
STANDBY/ON
ENTER
STANDBY
RETURN
SETUP
A
SPEAKERS
PHONES
B
+
TONE
STEREO
LISTENING MODE
DISPLAY DIGITAL INPUT
RT/PTY/TP MEMORY TUNING MODE
CLEAR
MULTl CH
DVD
VIDEO 1/VCR
VIDEO
2
VIDEO
3
TAPE
TUNER
CD
Note:
the remote controller’s [TEST TONE] button to output
the test tone, use the [LEVEL–] and [LEVEL+] but-
tons to adjust the levels, and use the [CH SEL] button
to select the speakers.
DIGITAL INPUT
Press and hold the AV receiver’s [DIGITAL
INPUT] button for about 3 seconds.
1
2
• If the multichannel input is selected (page 37), in step
2, the “3. MultiLevel” menu appears instead of the
“3. Level Cal” menu, and you can adjust the level of
each channel of the multichannel input regardless of
the Speaker Configuration settings.
While “Auto” is displayed (about 3 sec-
onds), press the [DIGITAL INPUT] button
again to select: PCM, DTS, or Auto.
DTS or PCM: The DTS or PCM indicator,
depending on which format you have set, flashes,
and only signals in that format are output. Digital
signals in other formats are ignored.
Auto (default): The format is detected automati-
cally. If no digital input signal is present, the cor-
responding analog input is used instead.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you can’t resolve the issue
yourself, contact your Onkyo dealer.
If your turntable uses an MC cartridge, you must con-
phono preamp.
• Specify the speaker distances and adjust the individual
speaker levels (pages 51, 52).
Power
• The input signal format is set to PCM or DTS. Set it to
Auto (page 52).
Can’t turn on the AV receiver?
• Make sure that the power cord is properly plugged into
the wall outlet.
• Unplug the power cord from the wall outlet, wait five
seconds or more, then plug it in again.
Only the front speakers produce sound?
• When the Stereo or Mono listening mode is selected,
only the front speakers and subwoofer produce sound.
• Make sure the speakers are configured correctly
(page 34).
The AV receiver turns off as soon as it’s turned
on?
Only the center speaker produces sound?
Music listening mode with a mono source, such as an
AM radio station or mono TV program, the sound is
concentrated in the center speaker.
• The amp protection circuit has been activated.
Remove the power cord from the wall outlet immedi-
ately. Disconnect all speaker cables and input sources,
and leave the AV receiver with its power cord discon-
nected for one hour. After that, reconnect the power
cord, and then set the volume to maximum. If the AV
receiver stays on, set the volume to minimum, discon-
nect the power cord, and reconnect your speakers and
input sources properly. If the AV receiver turns off
when you set the volume to maximum, disconnect the
power cord, and contact your Onkyo dealer.
• Make sure the speakers are configured correctly
(page 34).
The surround speakers produce no sound?
• When the Stereo or Mono listening mode is selected,
• Depending on the source and current listening mode,
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
• Make sure the speakers are configured correctly
(page 34).
Audio
There’s no sound or it’s very quiet?
• Make sure that the digital input source is selected
properly (page 33). Press the [DIGITAL INPUT] but-
ton repeatedly.
• Make sure that all audio connecting plugs are pushed
in all the way (page 22).
correct, and that the bare wires are in contact with
metal part of each speaker terminal (page 18)
• Make sure that the speaker cables are not shorting.
• Check the volume. It can be set to MIN, 1 through 79,
home theater enjoyment and has a wide volume range
for precise adjustment.
press the remote controller’s [MUTING] button to
unmute the AV receiver (page 42).
• While a pair of headphones is connected to the
PHONES jack, no sound is output by the speakers
(page 43).
• Check the digital audio output setting on the con-
nected device. On some games consoles, such as those
that can play DVDs, the default setting is off.
• With some DVD-Video discs, you need to select an
audio format from a menu.
The center speaker produces no sound?
• When the Stereo or Mono listening mode is selected,
the center speaker produces no sound (page 44).
• Make sure the speakers are configured correctly
(page 34).
The subwoofer produces no sound?
• The subwoofer outputs no sound while only speaker
• When you play source material that contains no infor-
mation in the LFE channel, the subwoofer produces
no sound.
• Make sure the speakers are configured correctly
(page 34).
• If the multichannel DVD input is selected and speaker
set B is on, speaker set A is reduced to 2-channel play-
back, so the subwoofer outputs no sound.
• On the AV receiver, the subwoofer setting in the
speaker configuration is set to No. Set the subwoofer
setting to Yes.
• If your turntable doesn’t have a phono preamp built-in,
you must connect one between it and the AV receiver.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
There’s no sound with a certain signal format?
• Check the digital audio output setting on the con-
nected device. On some games consoles, such as those
that can play DVDs, the default setting is off.
• With some DVD-Video discs, you need to select an
audio output format from a menu.
Video
There’s no picture?
• Make sure that all video connecting plugs are pushed
in all the way (page 22).
• Make sure that each video component is properly con-
nected.
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
Can’t get 5.1-channel playback?
to 2.1-channel playback.
The volume cannot be set to 79?
• When the levels of all speakers have been calibrated
(pages 43, 51), the maximum volume setting may
change.
Tuner
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesn’t
appear?
• Relocate your antenna.
• Move the AV receiver away from your TV or com-
puter.
• Listen to the station in mono (page 38).
• When listening to anAM station, operating the remote
controller may cause noise.
Noise can be heard?
• Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance, so don’t do it.
repositioning your cables.
The Late Night function doesn’t work?
• Make sure the source material is Dolby Digital
(page 48).
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
The DVD analog multichannel input doesn’t
work?
• Check the DVD analog multichannel input connec-
tions (page 25).
• To select the DVD analog multichannel input, press
the [MULTI CH] input selector button.
• Check the audio output settings on your DVD player.
About DTS signals
• When DTS program material ends and the DTS bit-
stream stops, the AV receiver remains in DTS listening
mode and the DTS indicator remains on. This is to pre-
vent noise when you use the pause, fast forward, or fast
reverse function on your player. If you switch your
player from DTS to PCM, because the AV receiver
does not switch formats immediately, you may not hear
any sound, in which case you should stop your player
for about three seconds, and then resume playback.
• With some CD players, you won’t be able to playback
DTS material properly even though your player is con-
nected to a digital input on the AV receiver. This is
usually because the DTS bitstream has been processed
(e.g., output level, sampling rate, or frequency
response changed) and the AV receiver doesn’t recog-
nize it as a genuine DTS signal. In such cases, you
may hear noise.
• When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player
may produce a short audible noise. This is not a mal-
function.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
Remote Controller
The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
The remote controller doesn’t work?
rect polarity (page 7).
away from the AV receiver, and that there’s no
obstruction between the remote controller and the AV
receiver’s remote control sensor (page 7).
• Make sure you’ve selected the correct remote control-
ler mode (page 12).
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
code.
Can’t control other components?
• Make sure you’ve selected the correct remote control-
ler mode (page 12).
• To control cassette tape deck, point the remote con-
troller at the AV receiver.
To reset the AV receiver to its factory defaults, turn
it on and, while holding down the [VIDEO 1/VCR]
button, press the [STANDBY/ON] button. “Clear”
will appear on the display and the AV receiver will
enter Standby mode.
• To control Onkyo CD player or MD/CD recorder,
point the remote controller at that component.
Before disconnecting the power cord from the wall out-
let, set the AV receiver to Standby.
Recording
Can’t record?
• On your recorder, make sure the correct input is
selected.
• To prevent signal loops and damage to the AV
receiver, input signals are not fed through to outputs
with the same name (e.g., TAPE IN to TAPE OUT, or
VIDEO 1 IN to VIDEO 1 OUT).
Others
The sound changes when I connect my head-
phones?
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct.
How do I change the language of a multiplex
source?
• Use the “Multiplex” setting on the “4. Audio Adjust”
menu to select Main or Sub (page 47).
The
functions don’t work?
• To use
, you must make an
connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected digi-
tally (page 31).
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
Amplifier Section
General
Power Output
2 channel driven:
Power Supply
North American: AC 120 V, 60 Hz
Australian and European:
AC 230-240 V, 50 Hz
Others: AC 120/220-240 V, 50/60 Hz
North American: 5.5 A
North American: 100 W + 100 W
(8Ω, 1 kHz, FTC)
European: 100 W + 100 W
(8Ω, 1 kHz, DIN)
Asian: 120 W + 120 W (8Ω, 1kHz, JEITA)
230 W + 230 W (3Ω, Front)
170 W + 170 W (4Ω, Front)
115 W + 115 W (8Ω, Front)
Power Consumption
Others: 380 W
Dynamic Power
Stand-by Power
Consumption
North American: 0.1 W
European: 0.2 W
Others: 0.5 W
THD (Total Harmonic
Distortion)
0.08% (Power Rated)
Dimensions
Damping Factor
Input Sensitivity and
Impedance
Output Level and
Impedance
60 (Front,1kHz,8Ω)
(W × H × D)
435 × 150 × 369 mm
17-1/8"
×
5-7/8"
×
14-1/2"
200 mV/ 47 kΩ (LINE)
Weight
North American and European: 8.8 kg
19.4 lbs.
Others: 9.6 kg, 19.0 lbs.
200 mV/ 470 Ω (REC OUT)
10 Hz–100 kHz/ +1 dB-3 dB (Direct
mode)
10 dB, 50 Hz (BASS)
10 dB, 20 kHz (TREBLE)
100 dB (LINE, IHF-A)
8Ω– 16Ω
Frequency Response
■ Video Inputs
Composite
Tone Control
DVD,VIDEO1,VIDEO2,VIDEO3
MONITOR,VIDEO1
Signal to Noise Ratio
Speaker Impedance
■ Video Outputs
Composite
Video Section
■ Audio Inputs
Digital Inputs
Optical: 1
Coaxial: 1
DVD(MULTICHANNEL),VIDEO1,
Input Sensitivity/Output
Level and Impedance
1 Vp-p /75Ω(Composite)
Analog Inputs
VIDEO2,VIDEO3,TAPE,CD
6
Tuner Section
Multichannel Inputs
■ Audio Outputs
Analog Outputs
Speaker Outputs
Phones
■ FM
TAPE,VIDEO1
SP-A (L, R, C, SL, SR, SW) + SP-B (L, R)
1
Tuning Frequency
Range
North American: 87.5 MHz– 107.9 MHz
European: 87.5 MHz– 108.0 MHz
Asian: 87.5 MHz– 108.0 MHz
Stereo:17.2 dBf 2 µV(75Ω IHF)
Mono: 11.2 dBf 1 µV(75Ω IHF)
Stereo: 70 dB (IHF-A)
Usable Sensitivity
Signal to Noise Ratio
THD
Mono:76 dB (IHF-A)
Stereo: 0.3% (1kHz)
Mono:0.2% (1kHz)
Frequency Response
Stereo Separation
30 Hz–15 kHz / 1 dB
45 dB (1kHz)
■ AM
Tuning Frequency
Range
North American: 530 kHz–1710 kHz
European: 522 kHz–1611 kHz
Asian: 530/522 kHz–1710/1611 kHz
Usable Sensitivity
Signal to Noise Ratio
THD
30 µV
40 dB
0.70%
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification—Continued
5.1ch Home Theater Speaker Pachage
■ Center Speaker (SKC-330C)
■ Passive Subwoofer (SKW-330)
Type:
2 Way Bass-reflex
Type:
Bass-reflex type
Impedance:
Maximum input power: 100 W
Output sound pressure
8 Ω
Impedance:
Maximum input power: 100 W
Output sound pressure
8 Ω
level:
86 dB/W/m
level:
84 dB/m/w
Frequency response:
Crossover frequency:
Cabinet capacity:
Dimensions
(W × H × D):
Weight:
80 Hz–22 kHz
10 kHz
0.081 cubic feet (2.3 L)
Frequency response:
Cabinet capacity:
Dimensions
(W × H × D):
Weight:
30 Hz–150 Hz
0.91 cubic feet (26 L)
9-1/16" × 17-1/8" × 15-7/16"
14-3/16"
×
5"
×
5-3/16"
(230 × 435 × 392 mm)
(360 × 127 × 131 mm)
17.2 lbs. (7.8 kg)
3.5 lbs. (1.6 kg)
Drivers unit:
Terminal:
8" (20 cm) Cone
Spring type color coded
Drivers unit:
3-1/8" (8 cm) Cone (Woofer) × 2
3/4" (2 cm) Ceramic (Tweeter)
Spring type color coded
2
North American model:
1/4" screw, Depth 5/16"
Ohter models:
Terminal:
Key hole slot:
Threaded insert:
■ Front Speaker (SKF-330F)
Type:
2 Way Bass-reflex
Impedance:
Maximum input power: 100 W
Output sound pressure
8 Ω
5 mm screw, Depth 8 mm
Fixed
Magnetic shielding
Grille:
Other:
level:
83 dB/W/m
Frequency response:
Crossover frequency:
Cabinet capacity:
Dimensions
(W × H × D):
Weight:
80 Hz–22 kHz
10 kHz
0.042 cubic feet (1.2 L)
5-13/16"
×
7-15/16"
×
4"
■ Surround Speaker (SKM-330S)
Type:
2 Way Bass Reflex
(148 × 202 × 101 mm)
Impedance:
Maximum input power: 100 W
Output sound pressure
8 Ω
2.0 lbs. (0.9 kg)
Drivers unit:
3-1/8" (8 cm) Cone (Woofer)
3/4" (2 cm) Ceramic (Tweeter)
Spring type color coded
1
North American model:
1/4" screw, Depth 5/16"
Ohter models:
level:
82 dB/W/m
Terminal:
Key hole slot:
Threaded insert:
Frequency response:
Crossover frequency:
Cabinet capacity:
Dimensions
(W × H × D):
Weight:
80 Hz–22 kHz
10 kHz
0.042 cubic feet (1.2 L)
5-13/16"
×
7-15/16"
×
4"
5 mm screw, Depth 8 mm
Fixed
Magnetic shielding
(148 × 202 × 101 mm)
Grille:
Other:
1.5 lbs. (0.7 kg)
Drivers unit:
3-1/8" (8 cm) Cone (Woofer)
3/4" (2 cm) Ceramic (Tweeter)
Spring type color coded
1
North American model:
1/4" screw, Depth 5/16"
Ohter models:
Terminal:
Key hole slot:
Threaded insert:
5 mm screw, Depth 8 mm
Fixed
Grille:
Specifications and features are subject to change without
notice.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
HOMEPAGE
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
I0503-2
SN 29343977A
(C) Copyright 2005 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 3 9 7 7 A *
Download from Www.Somanuals.com. All Manuals Search And Download.
|