Onkyo Stereo System HT S3300 User Manual

Contents

5.1ch Home Theater System

Introduction ...................................2

Connections.................................12

Turning On & Basic Operations ......20

Advanced Operations .................30

HT-S3300

AV Receiver (HT-R380)

Speaker Package (HTP-380)

Front Speakers (SKF-380 L/R)

Center Speaker (SKC-380/SKC-380C)

Surround Speakers (SKR-380 L/R)

Subwoofer (SKW-380)

Controlling iPod & Other

Instruction Manual

Components............................40

Others...........................................47

Thank you for purchasing an Onkyo 5.1ch Home

Theater System. Please read this manual thoroughly

before making connections and plugging in the unit.

Following the instructions in this manual will enable

you to obtain optimum performance and listening

enjoyment from your new 5.1ch Home Theater

System.

Please retain this manual for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions

1. Recording Copyright—Unless it’s for personal use

only, recording copyrighted material is illegal without

the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not user-ser-

viceable. If you cannot turn on the unit, contact your

Onkyo dealer.

3. Care—Occasionally you should dust the unit all over

with a soft cloth. For stubborn stains, use a soft cloth

dampened with a weak solution of mild detergent and

water. Dry the unit immediately afterwards with a

clean cloth. Don’t use abrasive cloths, thinners, alco-

hol, or other chemical solvents, because they may

damage the finish or remove the panel lettering.

4. Power

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved

by the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee

that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio

or television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit differ-

ent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV techni-

cian for help.

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SECTION

CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the volt-

age requirements printed on the unit’s rear panel (e.g.,

AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit

from the AC power source. Make sure that the plug is

readily operable (easily accessible) at all times.

Pressing ON/STANDBY to select Standby mode does

not fully shutdown the unit. If you do not intend to use

the unit for an extended period, remove the power cord

from the AC outlet.

5. Preventing Hearing Loss

Caution

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS COM-

PLIES WITH CANADIAN ICES-003.

Excessive sound pressure from earphones and head-

phones can cause hearing loss.

6. Batteries and Heat Exposure

Warning

For models having a power cord with a polarized plug:

Batteries (battery pack or batteries installed) shall not

be exposed to excessive heat as sunshine, fire or the

like.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

7. Never Touch this Unit with Wet Hands—Never han-

dle this unit or its power cord while your hands are

wet or damp. If water or any other liquid gets inside

this unit, have it checked by your Onkyo dealer.

8. Handling Notes

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME NMB-

003 DU CANADA.

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally

bought it.

• Do not leave rubber or plastic items on this unit for

a long time, because they may leave marks on the

case.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE

DE LA FICHE DANS LA BORNE CORRESPON-

DANTE DE LA PRISE ET POUSSER JUSQU’AU

FOND.

• This unit’s top and rear panels may get warm after

prolonged use. This is normal.

• If you do not use this unit for a long time, it may not

work properly the next time you turn it on, so be

sure to use it occasionally.

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker Precautions

Package Contents

Make sure you have the following items:

AV Receiver HT-R380

Placement

• The subwoofer cabinet is made out of wood and is there-

fore sensitive to extreme temperatures and humidity, do

not put it in locations subject to direct sunlight or in

humid places, such as near an air conditioner, humidifier,

bathroom, or kitchen.

HT-R380 (➔ 7)

Remote controller and two batteries (AA/R6) (➔ 5)

Indoor FM antenna (➔ 18)

• Do not put water or other liquids close to the speakers. If

liquid is spilled over the speakers, the drive units may be

damaged.

AM loop antenna (➔ 18)

In catalogs and on packaging, the letter at the end of the prod-

uct name indicates the color. Specifications and operations are

the same regardless of color.

• Speakers should only be placed on sturdy, flat surfaces

that are free from vibration. Putting them on uneven or

unstable surfaces, where they may fall and cause dam-

age, will affect the sound quality.

• Subwoofer is designed to be used in the upright vertical

position only. Do not use it in the horizontal or tilted

position.

• If the unit is used near a turntable, CD player or Blu-ray

Disc/DVD player, howling or slipping of sound may

occur. To prevent this, move the unit away from the turn-

table, CD player or Blu-ray Disc/DVD player, otherwise

lower the unit’s output level.

Speaker Package HTP-380

Front speakers (SKF-380 L/R) (➔ 9)

Center speaker (SKC-380/SKC-380C) (➔ 9)

Surround speakers (SKR-380 L/R) (➔ 9)

Subwoofer (SKW-380) (➔ 9)

Speaker Package Accessories

Speaker cables for front speakers 11 ft. (3.5 m)

(White and Red) (➔ 13)

Using Close to a TV or Computer

Speaker cable for center speaker 10 ft. (3.0 m)

(Green) (➔ 13)

TVs and computer monitors are magnetically sensitive

devices and as such are likely to suffer discoloration or

picture distortion when conventional speakers are placed

nearby. To prevent this, the SKF-380 and SKC-380/

SKC-380C feature internal magnetic shielding. In some

situations, however, discoloration may still be an issue, in

which case you should turn off your TV or monitor, wait

15 to 30 minutes, and then turn it back on again. This nor-

mally activates the degaussing function, which neutralizes

the magnetic field, thereby removing any discoloration

effects. If discoloration problems persist, try moving the

speakers away from your TV or monitor. Note that discol-

oration can also be caused by a magnet or demagnetizing

tool that’s too close to your TV or monitor.

Speaker cables for surround speakers 26 ft. (8.0 m)

(Blue and Gray) (➔ 13)

Speaker cable for subwoofer 10 ft. (3.0 m)

(Purple) (➔ 13)

16 thin rubber stoppers, 12 thick rubber stoppers

(➔ 14)

4 floor pads for the subwoofer (➔ 14)

Do not place SKR-380 close to TV or a computer monitor

because they have no magnetic shield.

Input Signal Warning

The speakers can handle the specified input power when

used for normal music reproduction. If any of the follow-

ing signals are fed to them, even if the input power is

within the specified rating, excessive current may flow in

the speaker coils, causing burning or wire breakage:

1. Interstation noise from an untuned FM radio.

2. Sound from fast-forwarding a cassette tape.

3. High-pitched sounds generated by an oscillator, elec-

tronic musical instrument, and so on.

4. Amplifier oscillation.

5. Special test tones from audio test CDs and so on.

6. Thumps and clicks caused by connecting or discon-

necting audio cables. (Always turn off your amplifier

before connecting or disconnecting cables.)

7. Microphone feedback.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Remote Controller

Installing the Batteries

Note

Contents

Introduction

Important Safety Instructions .........................................2

Precaution s .......................................................................3

Speaker Precaution s ........................................................4

Package Contents ............................................................4

Features ............................................................................6

Front & Rear Panels.........................................................7

Speaker Packag e ..............................................................9

Remote Controller..........................................................10

About Home Theate r ......................................................1 1

• If the remote controller

doesn’t work reliably, try

replacing the batteries.

• Don’t mix new and old

batteries or different

types of batteries.

• If you intend not to use

the remote controller for

Batteries (AA/R6)

a long time, remove the batteries to prevent damage from leak-

age or corrosion.

Connections

• Remove expired batteries as soon as possible to prevent damage

from leakage or corrosion.

Connecting the AV Receiver .........................................1 2

Turning On & Basic Operations

Aiming the Remote Controller

Turning On/Off the AV Receiver ...................................2 0

Basic Operations............................................................21

Listening to the Radio....................................................2 3

Recording........................................................................26

Using the Listening Modes............................................2 7

To use the remote controller, point it at the AV receiver’s

remote control sensor, as shown below.

Remote control sensor

AV receiver

Advanced Operations

Advanced Setup .............................................................30

Controlling iPod & Other Components

Controlling iPod .............................................................4 0

Controlling Other Components.....................................4 4

Approx. 16 ft. (5 m)

Others

Troubleshooting.............................................................47

Specifications.................................................................51

About HDMI.....................................................................53

Using an RIHD-compatible TV, Player, or Recorder ...54

To reset the AV receiver to its factory defaults, turn it

on and, while holding down VCR/DVR, press

ON/STANDBY (➔ 47).

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

AV Receiver HT-R380

Manufactured under license under U.S. Patent #’s: 5,451,942;

5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535;

7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and

worldwide patents issued & pending. DTS is a registered

trademark and the DTS logos, Symbol are trademarks of DTS,

Inc.

• 110 Watts/Channel @ 6 ohms

• 120 Watts/Channel @ 6 ohms (JEITA)

• Optimum Gain Volume Circuitry

• H.C.P.S. (High Current Power Supply) Massive High

Power Transformer

• HDMI (Ver.1.4 with Audio Return Channel, 3D), Deep-

Color, x.v.Color , Lip Sync, DTS -HD Master Audio,

DTS-HD High Resolution Audio, Dolby TrueHD ,

Dolby Digital Plus, DSD and Multi-CH PCM

• Non-Scaling Configuration

• A-Form Listening Mode Memory

• Direct Mode

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are trade-

marks of Dolby Laboratories.

Music Optimizer™ is a trademark of Onkyo Corporation.

• Music Optimizer for Compressed Digital Music files

• 192 kHz/24-bit D/A Converters

• Powerful and Highly Accurate 32-bit Processing DSP

“HDMI, the HDMI Logo, and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI

Licensing LLC in the United States and other countries.”

• 3 HDMI Inputs and 1 Output

• Onkyo p for System Control

• 3 Digital Inputs (2 Optical/1 Coaxial)

• Component Video Switching (2 Inputs/1 Output)

The HD Radio Ready logo is a proprietary trademark of iBiq-

uity Digital Corp.

To receive HD Radio broadcasts, you must install an Onkyo

UP-HT1 HD Radio tuner module (sold separately).

• Universal Port for the Dock for iPod /HD Radio™

tuner module (North American models)/DAB+ tuner

module (Asian models)

• Banana Plug-Compatible Speaker Posts

(Front Speakers A Only)

• 40 FM/AM Presets

Manufactured under license from Audyssey Laboratories™.

U.S. and foreign patents pending.

Audyssey EQ™, Audyssey Dynamic Volume™ and

Audyssey Dynamic EQ™ are trademarks of Audyssey Labo-

ratories.

• Audyssey EQ to Correct Room Acoustic Problems

• Audyssey Dynamic EQ for Loudness Correction

• Audyssey Dynamic Volume to Maintain Optimal Lis-

tening Level and Dynamic Range

• EX.BASS for natural deeper bass

• Crossover Adjustment

Apple and iPod are trademarks of Apple Inc., registered in the

U.S. and other countries.

“x.v.Color” is a trademark of Sony Corporation.

(40/50/60/80/100/120/150/200 Hz)

• A/V Sync Control Function (up to 100 ms)

• On-Screen Display via HDMI

Speaker Package HTP-380

SKF-380 L/R Full-Range Front Speakers

SKC-380 (North American models)/SKC-380C (Asian

models) Full-Range Center Speaker

• 3-1/4" (8 cm) full-range speaker

• Gloss Finished

• Max. input power: 120 W

• Magnetically shielded

• Color-coded speaker terminals and speaker cable

• 6-ohm impedance

SKR-380 L/R Full-Range Surround Speakers

• 3-1/4" (8 cm) full-range speaker

• Gloss Finished

• Max. input power: 120 W

• Color-coded speaker terminals and speaker cable

• 6-ohm impedance

SKW-380 Bass Reflex Subwoofer

• 8" (20 cm) cone woofer

• Down-Firing

• Color-coded speaker terminals and speaker cable

Download from Www.Somanuals.com. All Manuals Search And Download.

Front & Rear Panels

Front Panel

North American models

b c d e f g

i j klm

q r

Asian models

The actual front panel has various logos printed on it. They are not shown here for clarity.

The page numbers in parentheses show where you can find the main explanation for each item.

a ON/STANDBY button (➔ 20)

b STANDBY indicator (➔ 20)

l DISPLAY button (➔ 21)

m SETUP button (➔ 30)

c HDMI THRU indicator (➔ 36)

d SPEAKERS A and B buttons (➔ 11, 22 )

e Remote control sensor (➔ 5)

n TUNING, PRESET (➔ 23 to 24), arrow and

ENTER buttons

o RETURN button

p MASTER VOLUME control (➔ 21)

q MUSIC OPTIMIZER button (➔ 21, 38)

r PHONES jack (➔ 22)

f TONE LEVEL and TONE buttons (➔ 39)

g Display (➔ 8)

h LISTENING MODE buttons (➔ 27)

i DIMMER button (North American models) (➔ 21)

j MEMORY button (➔ 24)

s Input selector buttons (➔ 21)

t AUX INPUT LINE IN jack (➔ 17)

u RT/PTY/TP button (Asian models) (➔ 24)

k TUNING MODE button (➔ 23)

Download from Www.Somanuals.com. All Manuals Search And Download.

Display

For detailed information, see the pages in parentheses.

a A and B speaker indicators (➔ 11 , 22)

b Audio input indicators

f RDS indicator (excluding North American models)

(➔ 24)

g SLEEP indicator (➔ 22)

h MUTING indicator (➔ 22)

i Message area

c Listening mode and format indicators (➔ 21, 27)

d Audyssey indicators (➔ 34, 38)

e Tuning indicators (➔ 23)

Rear Panel

h i

b c

def

a DIGITAL IN COAXIAL and OPTICAL jacks

b COMPONENT VIDEO IN and OUT jacks

c HDMI IN and OUT jacks

i SPEAKERS terminals

(SURR, CENTER)

j FRONT SPEAKERS B terminals

k Power cord

d FM ANTENNA jack and AM ANTENNA terminal

e MONITOR OUT V jack

l u REMOTE CONTROL jack

m Composite video and analog audio jacks

f UNIVERSAL PORT jack

(BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN,

g FRONT SPEAKERS A terminals

h SUBWOOFER terminals

GAME IN, TV/CD IN)

See “Connecting the AV Receiver” for connection infor-

mation (➔ 12 to 19).

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker Package

Front, Center, Surround Speakers and Subwoofer

(SKF-380, SKC-380/SKC-380C, SKR-380, SKW-380)

SKR-380

SKF-380

Front

Rear

Front

Rear

SKW-380

SKC-380/SKC-380C

Front

Rear

a Speaker terminals

b Keyhole slots

These push terminals are for connecting the speaker to

the HT-R380 with the supplied speaker cables.

The supplied speaker cables are color-coded for easy

identification. Simply connect each cable to the same-

colored positive speaker terminal.

These keyhole slots can be used to wall-mount the

speaker. See “Wall Mounting” for mounting instruc-

tions (➔ 14).

Caution

• The front grilles are not designed to be removed so do

not attempt to remove them forcibly, as this will damage

them.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Controller

Controlling the AV Receiver

To control the A V r eceiver, press RECEIVER to select

Receiver mode.

You can also use the remote controller to control

Onkyo Blu-ray Disc/DVD player, CD player, and

other components.

See “Entering Remote Control Codes” for more

details (➔ 44).

For detailed information, see the pages in parentheses.

a ON/STANDBY button (➔ 20 )

b REMOTE MODE/INPUT SELECTOR buttons

(➔ 21, 44 to 45)

c TONE, + and – buttons (➔ 39)

d SP A/B button (➔ 11, 22)

e Arrow q/w/e/r and ENTER buttons

f SETUP button (➔ 30)

g LISTENING MODE buttons (➔ 27)

h DIMMER button (➔ 21)

i DISPLAY button (➔ 21)

j MUTING button (➔ 22)

k VOL q/w button (➔ 21)

l RETURN button

m AUDIO button (➔ 37)

n SLEEP button (➔ 22)

■ Controlling the tuner

To control the AV receiver’s tuner, press TUNER (or

RECEIVER).

You can select AM or FM by pressing TUNER repeatedly.

a Arrow q/w buttons (➔ 23)

c DISPLAY button (➔ 24)

d TUN MODE button (➔ 23)

e CH +/– button (➔ 24)

f Number buttons (➔ 23)

b D.TUN button (➔ 23)

Download from Www.Somanuals.com. All Manuals Search And Download.

About Home Theater

Speakers A and B

You can use two sets of speakers with the AV receiver: Speakers A and Speakers B.

Speakers A should be used in your main listening room for up to 5.1-channel playback.

While Speakers B is on, Speakers A is reduced to 2.1-channel playback.

Speakers B can be used in another room and offers 2-channel stereo playback.

Speakers A

Speakers B

Indicator Output

Speakers A: 2.1 channels

Speakers B: 2 channels

Off

Speakers A: 5.1 channels

Speakers B: 2 channels

No sound

Off

Enjoying Home Theater

Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your

own home—just like being in a movie theater or concert hall. With Blu-ray Discs, you can enjoy DTS and Dolby Digital.

With analog or digital TV, you can enjoy Dolby Pro Logic II, DTS Neo:6, or Onkyo’s original DSP listening modes.

a Front speakers (SKF-380)

These output the overall sound. Their role in a home theater is to provide

a solid anchor for the sound image. They should be positioned facing the

listener at about ear level, and equidistant from the TV. Angle them inward

so as to create a triangle, with the listener at the apex.

Speakers A: Main Room

b Center speaker (SKC-380/SKC-380C)

This speaker enhances the front speakers, making sound movements dis-

tinct and providing a full sound image. In movies it’s used mainly for dia-

log. Position it close to your TV facing forward at about ear level, or at the

same height as the front speakers.

Corner

position

While Speakers B is on, this speaker outputs no sound.

c Surround speakers (SKR-380)

These speakers are used for precise sound positioning and to add realistic

ambience. Position them at the sides of the listener, or slightly behind,

about 2 to 3 feet (60 to 100 cm) above ear level. Ideally they should be

equidistant from the listener.

1/3 of wall

position

While Speakers B is on, these speakers outputs no sound.

d Subwoofer (SKW-380)

The subwoofer handles the bass sounds of the LFE (Low-Frequency

Effects) channel. The volume and quality of the bass output from your

subwoofer will depend on its position, the shape of your listening room,

and your listening position. In general, a good bass sound can be obtained

by installing the subwoofer in a front corner, or at one-third the width of

the wall, as shown.

Speakers B: Sub Room

Tip

• To find the best position for your subwoofer, while playing a movie or some

music with good bass, experiment by placing your subwoofer at various

positions within the room, and choose the one that provides the most satis-

fying results.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the AV Receiver

• Be careful not to short the positive and negative wires.

Connecting Your Speakers

Doing so may damage the AV receiver.

• Make sure the metal core of the wire does not have con-

tact with the AV receiver’s rear panel. Doing so may

damage the AV receiver.

Speaker Configuration

The following table indicates the channels you should use

depending on the number of speakers that you have.

For 5.1-channel surround-sound playback, you need five

speakers and a powered subwoofer.

Number of channels

Front speakers

✔

Center speaker

Surround speakers

✔

No matter how many speakers you use, a powered sub-

woofer is recommended for a really powerful and solid

bass.

To get the best from your surround sound system, you

need to set the speaker settings. You can do this manually

(➔ 32).

Connecting the Speaker Cables

The AV receiver’s positive (+) speaker terminals are color-

coded for ease of identification. (The negative (–) speaker

terminals are all black.)

Speaker

Color

White

Red

Front left

• Don’t connect more than one cable to each speaker ter-

minal. Doing so may damage the AV receiver.

• Don’t connect one speaker to several terminals.

Front right

Center

Green

Blue

Surround left

Surround right

Subwoofer

Gray

Purple

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between

6 and 16 ohms. If you use speakers with a lower imped-

ance, and use the amplifier at high volume levels for a

long period of time, the built-in amp protection circuit

may be activated.

• Disconnect the power cord from the wall outlet before

making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other

words, connect positive (+) terminals only to positive (+)

terminals, and negative (–) terminals only to negative (–)

terminals. If you get them the wrong way around, the

sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may

affect the sound quality and should be avoided.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Speaker Cables

Screw-type speaker terminals

Strip 1/2" to 5/8" (12 to 15 mm) of insu-

lation from the ends of the speaker

cables, and twist the bare wires tightly,

as shown.

1/2" to 5/8" (12 to 15 mm)

(Supplied speaker cables are already

stripped.)

Using Banana Plugs (North American models)

• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.

• Do not insert the speaker code directly into the center hole of the speaker terminal.

Push-type speaker terminals

Strip 3/8" to 1/2" (10 to 12 mm) of insulation from the ends of the

speaker cables, and twist the bare wires tightly, as shown.

3/8" to 1/2" (10 to 12 mm)

(Supplied speaker cables are already stripped.)

The following illustration shows which speaker should be connected to each pair of terminals.

Surround Surround

right

left

speaker

Center speaker

Green

Gray

Blue

White

Red

Purple

Front right

speaker A

Front right

speaker B

Front left

speaker A

Subwoofer

Front left

speaker B

Speakers A

Speakers B

Download from Www.Somanuals.com. All Manuals Search And Download.

Wall Mounting

• Leave a gap of between 3/16"

(5 mm) and 7/16" (10 mm)

between the wall and the base

of the screw head, as shown.

(We recommend that you con-

sult a home installation profes-

sional.)

Wall

The speakers can easily be wall mounted by using the key-

hole slots. To prevent the speaker from vibrating against

the wall, attach two of the supplied thick rubber stoppers

to the rear of each speaker.

3/16" to 7/16"

(5 mm to 10 mm)

To mount the front or surround speakers vertically, use the

keyhole slot shown to hang each speaker on a screw that’s

securely screwed into the wall.

Using the Rubber Stoppers for a More

Stable Platform

Front speakers (SKF-380)

We recommend using the provided rubber stoppers to

achieve the best possible sound from your speakers. The

rubber stoppers prevent the speakers from moving, provid-

ing a more stable platform. Use thick stoppers for the cen-

ter speaker, and thin stoppers for the other speakers.

Keyhole slot for wall

mounting

Thin rubber stoppers

Thick

rubber

stoppers

Bottom of the

SKR-380

Bottom of the

SKF-380

Surround speakers (SKR-380)

Keyhole slot for wall

mounting

Thick

Thick rubber stoppers

rubber

stoppers

To mount the center speaker horizontally, use the two key-

hole slots shown to hang each speaker on two screws that

are securely screwed into the wall.

2-3/16"

(55 mm)

Bottom of the

SKC-380/SKC-380C

1/2" (12 mm)

Center speaker (SKC-380/SKC-380C)

Using the Floor Pads for Subwoofer

Keyhole slot for wall mounting

If the subwoofer is placed on a hard floor (wood, vinyl,

tile, etc.) and playback is very loud, the subwoofer’s feet

may damage the flooring. To prevent this, place the sup-

plied pads underneath the subwoofer’s feet. The pads also

provide a stable base for the subwoofer.

Thick

rubber

stoppers

8-9/16" (217 mm)

Caution

• A mounting screw’s ability to support a speaker depends

on how well it’s anchored to the wall. If you have hollow

walls, screw each mounting screw into a stud. If there are

no studs, or the walls are solid, use suitable wall anchors.

• Use screws with a head diameter of 5/16" (9 mm) or less

and a shank diameter of 1/8" (4 mm) or less. With hol-

low walls, use a cable/pipe detector to check for any

power cables or water pipes before making any holes.

Pad

Download from Www.Somanuals.com. All Manuals Search And Download.

About AV Connections

Connected image with AV components

: Video & Audio

HDMI cable

: Video

: Audio

Other cables

AV receiver

Blu-ray Disc/

DVD player

Blu-ray Disc/

DVD player

Game console

TV, projector, etc.

• Before making any AV connections, read the manuals supplied with your AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunc-

tions).

Right!

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

Wrong!

AV Cables and Jacks

Signal

Cable

Jack

Description

Video and

Audio

HDMI

HDMI connections can carry digital video and audio. The

AV receiver is compliant with HDMI.

HDMI

Video

Component video

Component video separates the luminance (Y) and color

difference signals (PR, PB), providing the best picture qual-

ity (some TV manufacturers label their component video

sockets slightly differently).

Green

P^B/CB

PR/CR

Blue

Red

Composite video

Composite video is commonly used on TVs, VCRs, and

See also:

• “Controlling Other Components” (➔ 44)

• “Controlling iPod” (➔ 40)

• “Listening to the Radio” (➔ 23)

The following information can typically be displayed.

Input source &

volume^*1

Signal format^*2

or sampling fre-

quency

To adjust the volume, use the MASTER VOLUME

control.

Select a listening mode and enjoy!

See also:

• “Using the Listening Modes” (➔ 27)

Input source &

listening mode^*3

When AM or FM radio is used, the band, preset number, and

frequency are displayed.

■ Operating with the remote controller

If the input signal is analog, no format information is dis-

Press RECEIVER followed by INPUT SELEC-

TOR.

played. If the input signal is PCM, the sampling frequency is

displayed. If the input signal is digital but not PCM, the signal

format is displayed.

Information is displayed for about three seconds, then the pre-

viously displayed information reappears.

Start playback on the source component.

See also:

• “Controlling Other Components” (➔ 44)

• “Controlling iPod” (➔ 40)

• “Listening to the Radio” (➔ 23 )

The input source is displayed with the default name even

when you have selected a name in “Name Edit” (➔ 35).

To adjust the volume, use VOL q/w.

Using the Music Optimizer

Select a listening mode and enjoy!

See also:

The Music Optimizer function enhances the sound quality

of compressed music files.

• “Using the Listening Modes” (➔ 27)

Press MUSIC OPTIMIZER on the front panel.

The M.Opt indicator lights on the display.

Note

• The maximum master volume level is affected by the subwoofer

volume level.

Tip

• Alternatively, you can use the remote controller’s AUDIO and

arrow buttons.

• See “Music Optimizer” for more details (➔ 38).

Setting the Display Brightness

You can adjust the brightness of the AV receiver’s display.

Press RECEIVER followed by DIMMER repeat-

edly to select: dim, dimmer, or normal brightness.

Tip

• Alternatively, you can use the AV receiver’s DIMMER (North

American models).

Download from Www.Somanuals.com. All Manuals Search And Download.

Muting the AV Receiver

Changing the Input Display

You can temporarily mute the output of the AV receiver.

When you connect an u-capable Onkyo component, you

must configure the input display so that u can work

properly.

Press RECEIVER followed by MUTING.

The output is muted and the MUTING indicator

flashes on the display.

This setting can be done only from the front panel.

Press TV/CD, GAME or VCR/DVR on the front

panel so that “TV/CD”, “GAME” or “VCR/DVR”

appears on the display.

Tip

• To unmute, press MUTING again or adjust the volume.

• The Mute function is cancelled when the AV receiver is set to

Standby.

Using the Sleep Timer

With the sleep timer, you can set the AV receiver to turn

off automatically after a specified period.

Press and hold down TV/CD, GAMEor VCR/DVR

Press RECEIVER followed by SLEEP repeatedly

to select the required sleep time.

The sleep time can be set from 90 to 10 minutes in

10 minute steps.

(about 3 seconds) to change the input display.

Repeat this step to select “MD”, “CDR”, “DOCK”

or “TAPE”.

For the TV/CD input selector, the input display

changes in this order:

The SLEEP indicator lights on the display when the

sleep timer has been set. The specified sleep time

appears on the display for about five seconds, then

the previous display reappears.

TV/CD → MD → CDR

→

TAPE

DOCK

For the GAME input selector, the setting changes in

this order:

Tip

• If you need to cancel the sleep timer, press SLEEP repeatedly

until the SLEEP indicator goes off.

GAME ↔ DOCK

• To check the time remaining until the AV receiver sleeps, press

SLEEP. Note that if you press SLEEP while the sleep time is

being displayed, you’ll shorten the sleep time by 10 minutes.

For the VCR/DVR input selector, the setting

changes in this order:

VCR/DVR ↔ DOCK

Using Headphones

Note

Connect a pair of stereo headphones with a stan-

dard plug (1/4 inch or 6.3 mm) to the PHONES

jack.

• DOCK can be selected for the TV/CD, GAME or VCR/DVR

input selector, but not at the same time.

• Enter the appropriate remote control code before using the

remote controller for the first time (➔ 44).

Note

• Always turn down the volume before connecting your head-

phones.

• While the headphones plug is inserted in the PHONES jack, the

speakers are turned off.

• When you connect a pair of headphones, the listening mode is

set to Stereo, unless it’s already set to Stereo, Mono, or Direct.

• The listening modes cannot be selected while a pair of head-

phones is connected.

Selecting Speakers A and B

You can use two sets of front speakers with the AV

receiver: Speakers A for up to 5.1-channel playback in

your main listening room and Speakers B for 2-channel

stereo playback in another room.

Press RECEIVER followed by SP A/B repeatedly

to cycle through the selection:

Speakers A → Speakers A&B → Speakers B

Off ←

A or B, or both indicators light on the display.

Note

• While Speakers B is on, channels are reduced to 2.1 in the main

room (➔ 11).

Tip

•

Alternatively, you can use the AV receiver’s SPEAKERS A and

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to the Radio

■ Manual tuning mode

This section describes the procedure using the but-

tons on the front panel unless otherwise specified.

Press TUNING MODEso that the AUTO indicator

goes off on the display.

Using the Tuner

Press and hold TUNING q/w.

The frequency stops changing when you release the

button.

With the built-in tuner you can enjoy AM and FM radio

stations. You can store your favorite stations as presets for

quick selection.

Press the buttons repeatedly to change the frequency

one step at a time.

Listening to the Radio

This model changes FM/AM frequency in 200/10kHz (or

50/9kHz) steps.

In manual tuning mode, FM stations will be in mono.

Press TUNER to select either “AM” or “FM”.

In this example, FM has been selected.

Each time you press TUNER, the radio band

changes between AM and FM.

Tuning into weak FM stereo stations

If the signal from a stereo FM station is weak, it may be

impossible to get good reception. In this case, switch to

manual tuning mode and listen to the station in mono.

Band

Frequency

Tip

• Alternatively, you can use the remote controller’s TUN MODE

and arrow buttons.

(Actual display depends on the country.)

Tuning into Radio Stations

■ Auto tuning mode

■ Tuning into stations by frequency

You can tune into AM and FM stations directly by enter-

ing the appropriate frequency.

On the remote controller, press TUNER repeat-

edly to select “AM” or “FM”, followed by D.TUN.

Press TUNING MODE so that the AUTO indicator

lights on the display.

Press TUNING q/w.

When tuned into a station, the TUNED indicator lights.

When tuned into a stereo FM station, the FM STEREO

indicator lights on the display, as shown.

Searching stops when a station is found.

(Actual display depends on the country.)

Within 8 seconds, use the number buttons to enter

the frequency of the radio station.

For example, to tune to 87.50 (FM), press 8, 7, 5, 0.

FM STEREO

AUTO

TUNED

Tip

• Alternatively, you can use the remote controller’s TUN MODE

and arrow buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

Presetting FM/AM Stations

Using RDS (excluding North American

models)

You can store a combination of up to 40 of your favorite

FM/AM radio stations as presets.

RDS works only in areas where RDS broadcasts are

available.

Tune into the FM/AM station that you want to

store as a preset.

See the previous section.

When tuned into an RDS station, the RDS indicator lights.

Press MEMORY.

The preset number flashes.

What is RDS?

RDS stands for Radio Data System and is a method of

transmitting data in FM radio signals. It was developed by

the European Broadcasting Union (EBU) and is available

in most European countries. Many FM stations use it these

days. In addition to displaying text information, RDS can

also help you find radio stations by type (e.g., news, sport,

rock, etc.).

While the preset number is flashing (about 8 sec-

onds), use PRESET e/r to select a preset from 1

through 40.

The AV receiver supports four types of RDS information:

Press MEMORY again to store the station or chan-

nel.

■ PS (Program Service)

The station or channel is stored and the preset num-

ber stops flashing.

Repeat this procedure for all of your favorite FM/

AM radio stations.

When tuned to an RDS station that’s broadcasting PS

information, the station’s name will be displayed. Press-

ing DISPLAY will display the frequency for 3 seconds.

■ RT (Radio Text)

When tuned to an RDS station that’s broadcasting text

information, the text will be shown on the display as

described in the next section.

Selecting Presets

To select a preset, use PRESET e/r on the AV

■ PTY (Program Type)

This allows you to search for RDS radio stations by type

(➔ 25).

receiver, or the remote controller’s CH +/–.

Tip

■ TP (Traffic Program)

This allows you to search for RDS radio stations that

broadcast traffic information (➔ 25).

• You can also use the remote controller’s number buttons to select

a preset directly.

Deleting Presets

Note

• In some cases, the text characters displayed on the AV receiver

may not be identical to those broadcast by the radio station. Also,

unexpected characters may be displayed when unsupported

characters are received. This is not a malfunction.

• If the signal from an RDS station is weak, RDS data may be

displayed intermittently or not at all.

Select the preset that you want to delete.

See the previous section.

While holding down MEMORY, press TUNING

MODE.

The preset is deleted and its number disappears from

the display.

When tuned to an RDS station that’s broadcasting text

information, the text can be displayed.

Displaying Radio Text (RT)

Press RT/PTY/TP once.

The RT information scrolls across the display.

Note

• The message “Waiting” may appear while the AV receiver waits

for the RT information.

• If the message “No Text Data” appears on the display, no RT

information is available.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ RDS program types (PTY)

Finding Stations by Type (PTY)

Type

Display

You can search for radio stations by type.

None

Press RT/PTY/TP twice.

The current program type appears on the display.

News reports

Current affairs

Information

Sport

News

Affairs

Info

Use PRESET e/r to select the type of program

Sport

you want.

Education

Educate

Drama

Culture

Science

Varied

See the table shown later in this chapter.

Drama

To start the search, press ENTER.

Culture

The AV receiver searches until it finds a station of

the type you specified, at which point it stops briefly

before continuing with the search.

Science and technology

Varied

Pop music

Rock music

Middle of the road music

Light classics

Serious classics

Other music

Weather

Pop M

Rock M

Easy M

Light M

Classics

Other M

Weather

Finance

Children

Social

When a station you want to listen to is found, press

ENTER.

If no stations are found, the message “Not Found”

appears.

Listening to Traffic News (TP)

You can search for stations that broadcast traffic news.

Finance

Children’s programmes

Social affairs

Religion

Press RT/PTY/TP three times.

If the current radio station is broadcasting TP (Traf-

fic Program), “[TP]” will appear on the display, and

traffic news will be heard as and when it’s broadcast.

If “TP” without square brackets appears, this means

that the station is not broadcasting TP.

Religion

Phone In

Travel

Phone in

Travel

Leisure

Jazz

Jazz music

Country music

National music

Oldies music

Folk music

Documentary

Alarm test

Alarm

To locate a station that is broadcasting TP, press

ENTER.

The AV receiver searches until it finds a station that’s

broadcasting TP.

If no stations are found, the message “Not Found”

appears.

Country

Nation M

Oldies

Folk M

Document

TEST

Alarm!

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording

This section explains how to record the selected input source to a component with recording capability, and how to record

audio and video from different sources.

Connecting a Recording Component

Recording Separate AV Sources

Here you can record audio and video from completely

separate sources, allowing you to overdub audio onto your

video recordings. This function takes advantage of the fact

that when an audio-only input source (TV/CD) is selected,

the video input source remains unchanged.

In the following example, audio from the CD player con-

nected to the TV/CD IN and video from the camcorder

connected to the BD/DVD IN are recorded by the VCR

connected to the VCR/DVR OUT jacks.

Camcorder

AUDIO

VIDEO

VCR,

DVD recorder

Cassette, CDR,

MD, etc.

Note

• The AV receiver must be turned on for recording. Recording is

not possible while it’s in Standby mode.

• If you want to record directly from your TV or playback VCR to

the recording VCR without going through the AV receiver, con-

nect the TV/VCR’s audio and video outputs directly to the

recording VCR’s audio and video inputs. See the manuals sup-

plied with your TV and VCR for details.

• Video signals connected to composite video inputs can be

recorded only via composite video outputs. If your TV/VCR is

connected to a composite video input, the recording VCR must

be connected to a composite video output.

• The surround sound and DSP listening modes cannot be

recorded.

CD player

VCR

Video signal

Audio signal

• Copy-protected Blu-ray discs and DVDs cannot be recorded.

• Sources connected to a digital input cannot be recorded. Only

analog inputs can be recorded.

• DTS signals will be recorded as noise, so don’t attempt analog

recording of DTS CDs or LDs.

Prepare the camcorder and CD player for play-

back.

Prepare the VCR for recording.

AV Recording

Audio sources can be recorded to a recorder (e.g., cassette

deck, CDR, MD) connected to the VCR/DVR OUT jacks.

Video sources can be recorded to a video recorder (e.g.,

VCR, DVD recorder) connected to the VCR/DVR OUT

jack.

Press BD/DVD input selector.

Press TV/CD input selector.

This selects the CD player as the audio source, but

leaves the camcorder as the video source.

Start recording on the VCR and start playback on

the camcorder and CD player.

The video from the camcorder and the audio from

the CD player are recorded by the VCR.

Use the input selector buttons to select the source

that you want to record.

You can watch the source while recording. The AV

receiver’s MASTER VOLUME control has no effect

on recording.

On your recorder, start recording.

On the source component, start playback.

If you select another input source during recording,

that input source will be recorded.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Listening Modes

Selecting Listening Modes

See “About Listening Modes” for detailed information about the listening modes (➔ 27).

Listening Mode Buttons

MOVIE/TV button

This button selects the listening modes intended for use

with movies and TV.

Press

RECEIVER first.

MUSIC button

This button selects the listening modes intended for use

with music.

GAME button

This button selects the listening modes intended for use

with video games.

STEREO button

This button selects the Stereo listening mode and All

Channel Stereo listening mode.

MUSIC

GAME

MOVIE/TV

STEREO

• The Dolby Digital and DTS listening modes can only be

selected if your Blu-ray Disc/DVD player is connected to

the AV receiver with a digital audio connection (coaxial,

optical, or HDMI).

• The listening modes you can select depends on the format

of the input signal. To check the format, see “Displaying

Source Information” (➔ 21).

• While a pair of headphones is connected, you can select the

following listening modes: Mono, Direct, and Stereo.

• The listening modes cannot be selected while a pair of

headphones is connected.

• While Speakers A and B are on, you can select only the

Direct, Stereo, Mono, or T-D (Theater-Dimensional) lis-

tening mode.

MOVIE/TV, MUSIC, GAME

About Listening Modes

The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidel-

ity and stunning surround sound.

Explanatory Notes

■ Input Source

The following audio formats are supported by the listening mode.

This is mono (monophonic) sound.

This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two speakers.

This is 5.1-channel surround sound. This surround system has five main channels of sound and a sixth subwoofer chan-

nel (called the point-one channel).

*1 This is 7.1-channel surround sound. This is a further sound enhancement to 5.1 channel sound with two additional speak-

ers that provide greater sound envelopment and more accurate positioning of sounds.

The AV receiver outputs this source in 5.1-channel surround sound.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Speaker Layout

The illustration shows which speakers are activated in each channel. See “Sp Config (Speaker Configuration)” for the

speaker setup (➔ 32).

a Front speakers

b Center speaker

c Subwoofer

d Surround speakers

Listening Modes

Listening Mode

Description

Input

Source Layout

Speaker

Direct

In this mode, audio from the input source is output without surround-sound process-

ing. The “Sp Config” (presence of speakers), “Sp Distance” and “A/V Sync” settings

are enabled, but much of the processing set via AUDIO is disabled. See “Advanced

Setup” for more details (➔ 30).

A ZX

S C

D i r e c t

Stereo

Sound is output by the front left and right speakers and subwoofer.

S t e r e o

Mono

Use this mode when watching an old movie with a mono soundtrack, or use it with the

foreign language soundtracks recorded in the left and right channels of some movies.

It can also be used with DVDs or other sources containing multiplexed audio, such as

karaoke DVDs.

M o n o

Multichannel

This mode is for use with PCM multichannel sources.

D XC

S XC

M u l t i c h

Dolby Pro Logic II

Dolby Pro Logic II expands any 2-channel source for 5.1-channel playback. It pro-

vides a very natural and seamless surround-sound experience that fully envelops the

listener. As well as music and movies, video games can also benefit from the dramatic

spatial effects and vivid imaging.

P L

M o v i e

M u s i c

G a m e

• Dolby PLII Movie

Use this mode with DVDs and videos that bear the Dolby Surround logo or TV shows

that feature Dolby Surround. You can also use this mode with stereo movies or TV

shows and the AV receiver will create a 5.1 surround mix from the 2-channel stereo.

• Dolby PLII Music

Use this mode to add 5.1 surround to stereo sources such as music CDs and DVDs.

• Dolby PLII Game

Use this mode when playing game discs.

Dolby Digital

D o l b y

Dolby Digital Plus^*1

In this mode, audio from the input source is output without surround-sound process-

ing. “Sp Config” (presence of speakers), “Crossover”, “Sp Distance”, “A/V Sync”

and much of the processing set via AUDIO are enabled. See “Advanced Setup” for

more details (➔ 30).

D XC

D o l b y

Dolby TrueHD

T r u e H D

DTS

D XC

D T S

DTS-HD High

Resolution Audio

D XC

D T S – H D H R

DTS-HD Master

Audio

D T S – H D MS T R

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening Mode

DTS Express

Description

Input

Source Layout

Speaker

(Continued from the previous page.)

S XC

D T S E x p r e s s

DSD^*2

D XC

S XC

D S D

DTS 96/24^*3

This mode is for use with DTS 96/24 sources. This is high-resolution DTS with a 96

kHz sampling rate and 24-bit resolution, providing superior fidelity. Use it with DVDs

that bear the DTS 96/24 logo.

D T S 9 6 / 2 4

DTS Neo:6

This mode expands any 2-channel source for up to 5.1-channel playback. It uses seven

full-bandwidth channels of matrix decoding for matrix-encoded material, providing a

very natural and seamless surround sound experience that fully envelops the listener.

• Neo:6 Cinema

Use this mode with any stereo movie (e.g., TV, DVD, VHS).

• Neo:6 Music

N e o : 6 C i n e m a

N e o : 6 M u s i c

Use this mode with any stereo music source (e.g., CD, radio, cassette, TV, VHS,

DVD).

Onkyo-Original DSP Listening Modes

Listening Mode

Orchestra

Description

Input

Source Layout

Speaker

Suitable for classical or operatic music, this mode emphasizes the surround channels

in order to widen the stereo image, and simulates the natural reverberation of a large

hall.

A C

O r c h e s t r a

Unplugged

Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the front

stereo image, giving the impression of being right in front of the stage.

U n p l u g g e d

Studio-Mix

Suitable for rock or pop music, listening to music in this mode creates a lively sound

field with a powerful acoustic image, like being at a club or rock concert.

S t u d i o – M i x

TV Logic

This mode adds realistic acoustics to TV shows produced in a TV studio, surround

effects to the entire sound, and clarity to voices.

T V L o g i c

Game-RPG

Use this mode when playing role playing game discs.

Use this mode when playing action game discs.

Use this mode when playing rock game discs.

Use this mode when playing sports game discs.

G a m e – R P G

Game-Action

G a m e – A c t i o n

Game-Rock

G a m e – R o c k

Game-Sports

G a m e – S p o r t s

All Ch Stereo

Ideal for background music, this mode fills the entire listening area with stereo sound

from the front, surround, and surround back speakers.

A XC

A l l C h S t

Full Mono

In this mode, all speakers output the same sound in mono, so the sound you hear is the

same regardless of where you are within the listening room.

F u l l M o n o

T-D (Theater-

Dimensional)

With this mode you can enjoy a virtual surround sound even with only two or three

speakers. This works by controlling how sounds reach the listener’s left and right ears.

Good results may not be possible if there’s too much reverb, so we recommend that

you use this mode in an environment with little or no natural reverb.

T – D

Note

For the Blu-ray Discs, Dolby Digital is used.

AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better

sound according to the player. In that case, set the output setting on the player side to PCM.

Depending on the input source, DTS is used.

• The listening modes cannot be selected with some source formats.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Setup

On-screen Setup Menus

Common Procedures in Setup Menu

The on-screen setup menus appear only on a TV that

is connected to the HDMI OUT. If your TV is con-

nected to the MONITOR OUT V or the COMPO-

NENT VIDEO OUT, use the AV receiver’s display

when changing settings.

Remote indicator

RECEIVER

Note

ENTER

The on-screen setup menus are displayed when:

• There is no video input, or

• The video input is 480p, 576p, 720p, 1080i, or 1080p.

q/w/e/r

SETUP

RETURN

Setup Menu

The on-screen setup menus appear on the connected TV

and provide a convenient way to change the AV receiver’s

various settings. Settings are organized into ten categories

on the main menu.

1. HDMI Input

2. Component

3. Digital Audio

4. Sp Config

5. Sp Distance

6. Level Cal

BD/DVD

VCR/DVR

CBL/SAT

GAME

Carry out the settings by using the on-screen display.

AUX

TV/CD

PORT

Press RECEIVER followed by SETUP.

The following menu appears.

7. Audio Adjust

8. Name Edit

9. Hardware

10. HDMI Setup

Setup Menu

1. HDMI Input

2. Component

3. Digital Audio

4. Sp Config

5. Sp Distance

6. Level Cal

BD/DVD

VCR/DVR

CBL/SAT

GAME

HDMI1

a HDMI Input (➔ 31)

f Level Cal (➔ 33)

HDMI2

HDMI3

AUX

BD/DVD

VCR/DVR

CBL/SAT

GAME

Left

TV/CD

PORT

Center

7. Audio Adjust

8. Name Edit

9. Hardware

Right

Surround Right

Surround Left

Subwoofer

AUX

10. HDMI Setup

TV/CD

PORT

Tip

b Component (➔ 31)

g Audio Adjust (➔ 33)

• If the main menu doesn’t appear, make sure the appropri-

ate external input is selected on your TV.

BD/DVD

VCR/DVR

CBL/SAT

GAME

Input Ch(Mux)

Input Ch(Mono)

Panorama

Use q/w to select a menu, and then press ENTER.

Dimension

AUX

Center Width

Center Image

Audyssey

TV/CD

Use q/w to select a target, and e/r to change the

setting.

PORT

Dynamic EQ

ReferenceLevel

Dynamic Volume

Listening Angle

c Digital Audio (➔ 31)

Press SETUP to close the menu.

Press RETURN to return to the main menu.

BD/DVD

VCR/DVR

CBL/SAT

GAME

h Name Edit (➔ 35)

Name

AUX

Note

TV/CD

PORT

• This procedure can also be performed on the AV receiver by

using SETUP, arrow buttons, and ENTER.

d Sp Config (➔ 32)

i Hardware (➔ 35)

Subwoofer

Front

Center

Remote ID

FM/AM Freq Step

Surround

Crossover

Double Bass

e Sp Distance (➔ 32)

j HDMI Setup (➔ 36)

Unit

Audio TV OUT

LipSync

HDMI Control

Audio Return Ch

Power Control

TV Control

Left

Center

Right

Surround Right

Surround Left

Subwoofer

Download from Www.Somanuals.com. All Manuals Search And Download.

Explanatory Notes

Component (Component Video Input)

Sp Config

Component

If you connect a video component to a component video

input, you must assign that input to an input selector. For

example, if you connect your Blu-ray Disc/DVD player to

COMPONENT VIDEO IN 2, you must assign “IN2” to

the “BD/DVD” input selector.

Subwoofer

Yes:

Select if a subwoofer is connected.

No:

Select if no subwoofer is connected.

Here are the default assignments.

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

a Menu selection

IN1

b Setting target

- - - - -

IN2

c Setting options (default setting underlined)

- - - - -

HDMI Input

AUX

TV/CD

HDMI Input

PORT

If you connect a video component to an HDMI input, you

must assign that input to an input selector. For example, if

you connect your Blu-ray Disc/DVD player to HDMI

IN 2, you must assign “HDMI2” to the “BD/DVD” input

selector.

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/

CD, PORT

`IN1, IN2:

Select a corresponding component video input that

the video component has been connected.

`- - - - -:

Here are the default assignments.

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

HDMI1

Select if you’re not using the COMPONENT

VIDEO OUT.

- - - - -

Note

HDMI2

• If you connect a component (such as UP-A1 Dock that seated

iPod) to the UNIVERSAL PORT jack, you cannot assign any

input to PORT selector.

HDMI3

AUX

- - - - -

TV/CD

- - - - -

PORT

- - - - -

Digital Audio (Digital Audio Input)

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/

CD, PORT

Digital Audio

`HDMI1, HDMI2, HDMI3:

If you connect a component to a digital audio input, you

must assign that input to an input selector. For example, if

you connect your CD player to the OPTICAL IN 1, you

must assign “OPT1” to the “TV/CD” input selector.

Here are the default assignments.

Select a corresponding HDMI input that the video

component has been connected.

`- - - - -:

Select if you’re not using the HDMI OUT.

Each HDMI input cannot be assigned to two input

selectors or more. When HDMI1 - HDMI3 have

already been assigned, you must set first any unused

input selectors to “- - - - -”, or you will be unable to

assign HDMI1 - HDMI3 to input selector.

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

COAX

- - - - -

OPT1

Note

AUX

- - - - -

• When an HDMI IN is assigned to an input selector as explained

here, the digital audio input for that input selector is automati-

cally set to the same HDMI IN (➔ 31, Digital Audio (Digital

Audio Input)).

TV/CD

OPT2

PORT

- - - - -

• If you connect a component (such as UP-A1 Dock that seated

iPod) to UNIVERSAL PORT jack, you cannot assign any input

to PORT selector.

• Do not assign the component connected with the HDMI input to

TV/CD selector when you set “TV Control” setting to “On”

(➔ 37). Otherwise, appropriate CEC (Consumer Electronics

Control) operation will not be guaranteed.

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/

CD, PORT

`COAX, OPT1, OPT2:

Select a corresponding digital audio input that the

component has been connected.

`- - - - -:

Select if the component is connected to an analog

audio input.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Crossover (Crossover Frequency)

This setting is advantageous for the speakers that you

specified as “Small” in the “Sp Config (Speaker Configura-

tion)” (➔ 32). To get the best bass performance from

your speaker system, you need to set the crossover fre-

quency according to the size and frequency response of

your speakers.

`40Hz, 50Hz, 60Hz, 80Hz, 100Hz, 120Hz, 150Hz,

200Hz:

Use the diameter of the smallest speaker in your system

when choosing the crossover frequency.

Note

• When an HDMI IN is assigned to an input selector in “HDMI

Input” (➔ 31), this input assignment is automatically set to the

same HDMI IN. And in addition to the usual inputs (e.g., COAX,

etc.), you can also select HDMI inputs.

• Available sampling rate for PCM signals from a digital input

(optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

• If you connect a component (such as UP-A1 Dock that seated

iPod) to the UNIVERSAL PORT jack, you cannot assign any

input to PORT selector.

Sp Config (Speaker Configuration)

Speaker cone diameter

Over 8 in. (20 cm)

Crossover frequency

40/50/60 Hz

Sp Config

6-1/2 to 8 in. (16 to 20 cm)

5-1/4 to 6-1/2 in. (13 to 16 cm)

3-1/2 to 5-1/4 in. (9 to 13 cm)

Under 3-1/2 in. (9 cm)

80 Hz

This section explains how to specify

which speakers are connected and their

sizes.

100 Hz

120 Hz

150/200 Hz

For speakers with a cone diameter larger

than 6-1/2 inches (16 cm), specify Large

(full band). For those with a smaller

Choose the setting suitable for the speaker.

Note

Cone diameter

diameter, specify Small (default crossover 120 Hz).

The crossover frequency can be changed in the “Crossover

(Crossover Frequency)” (➔ 32).

• For a more accurate setting, look up the frequency response in

the manuals supplied with your speakers and set accordingly.

• Choose a higher crossover frequency if you want more sound

from your subwoofer.

Note

■ Double Bass

• Speaker Configuration, Crossover Frequency, and Double Bass

settings cannot be changed while headphones are connected, or

“Audio TV OUT” setting is set to “On” (➔ 36) or speaker set

B is on.

Note

• This function can be set only if the “Subwoofer” setting is set to

“Yes”, and the “Front” setting is set to “Large” (➔ 32).

■ Subwoofer

`Yes:

Select if a subwoofer is connected.

`No:

With the Double Bass function, you can boost bass out-

put by feeding bass sounds from the front left, right, and

center channels to the subwoofer.

`On:

Select if no subwoofer is connected.

Double Bass function on.

`Off:

■ Front

Double Bass function off.

`Small:

`Large:

Sp Distance (Speaker Distance)

Select based on the cone diameter.

Note

Sp Distance

• If the “Subwoofer” setting is set to “No”, this setting is fixed at

Here you can specify the distance from each speaker to the

listening position so that the sound from each speaker

arrives at the listener’s ears as the sound designer

intended.

“Large” and does not appear.

*1*2

■ Center

*1*2

, Surround

`Small:

`Large:

■ Unit

`feet:

Select based on the cone diameter.

`None:

Select if no speaker is connected.

Distances can be set in feet. Range: 1ft to 30ft in

1 foot steps.

`meters:

Distances can be set in meters. Range: 0.3m to 9.0m

in 0.3 meter steps.

(The default setting varies from country to country.)

Note

If the “Front” setting is set to “Small”, the “Large” option

cannot be selected.

While Speakers B is on, these speakers output no sound

(➔ 11).

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Left, Center, Right, Surround Right, Surround

Left, Subwoofer

■ Input Ch(Mux)

`Main:

`Specify the distance from the each speaker to your lis-

tening position.

The main channel is output.

`Sub:

The sub channel is output.

`M/S:

Both the main and sub channels are output.

Mono

Note

• The speaker distance setting cannot be changed while a pair of

headphones is connected, or “Audio TV OUT” setting is set to

“On” (➔ 36) or Speakers B is on.

• Speakers that you set to “No” or “None” in the “Sp Config

(Speaker Configuration)” (➔ 32) cannot be selected.

• The Center, Right, and Subwoofer distances can be set up to 5 ft.

(1.5 m) more or less than the Left distance. For example, if the

Left distance is set to 20 ft. (6 m), the Center, Right, and Sub-

woofer distances can be set between 15 and 25 ft. (4.5 and

7.5 m).

• The Surround distances can be set up to 5 ft. (1.5 m) more or

15 ft. (4.5 m) less than the Left distance. For example, if the Left

distance is set to 20 ft. (6 m), the SurrRight and SurrLeft dis-

tances can be set between 5 and 25 ft. (1.5 and 7.5 m).

This setting specifies the channel to be used for playing

any 2-channel digital source such as Dolby Digital, or 2-

channel analog/PCM source in the Mono listening mode.

■ Input Ch(Mono)

`L+R:

Both the left and right channels are output.

`Left:

Only the left channel is output.

`Right:

Only the right channel is output.

Level Cal (Level Calibration)

Dolby Settings

Level Cal

PLII Music (2ch Input)

These settings apply to only 2-channel stereo sources.

Here you can adjust the level of each speaker with the

built-in test tone so that the volume of each speaker is the

same at the listening position.

■ Panorama

`On:

Panorama function on.

`Off:

■ Left, Center , Right, Surround Right, Surround

Left

Panorama function off.

`–12 dB to 0 dB to +12 dB in 1 dB step.

With this setting, you can broaden the width of the front

stereo image when using the Dolby Pro Logic II Music

listening mode.

■ Subwoofer

` –15 dB to 0 dB to +12 dB in 1 dB step.

Note

■ Dimension

• Speakers that you set to “No” or “None” in the “Sp Config

(Speaker Configuration)” (➔ 32) cannot be selected.

• The speakers cannot be calibrated while a pair of headphones is

connected, Speakers B is on, or “Audio TV OUT” setting is set

to “On” (➔ 36) or the AV receiver is muted.

`–3 to 0 to +3

With this setting, you can move the sound field forward

or backward when using the Dolby Pro Logic II Music

listening mode. Higher settings move the sound field

backward. Lower settings move it forward.

If the stereo image feels too wide, or there’s too much

surround sound, move the sound field forward to

improve the balance. Conversely, if the stereo image

feels like it’s in mono, or there’s not enough surround

sound, move it backward.

For the center speaker and subwoofer, the level settings made

by using AUDIO are saved.

Tip

• If you’re using a handheld sound level meter, adjust the level of

each speaker so that it reads 75 dB SPL at the listening position,

measured with C-weighting and slow reading.

■ Center Width

`0 to 3 to 7

Audio Adjust

With this setting, you can adjust the width of the sound

from the center speaker when using the Dolby Pro

Logic II Music listening mode. Normally, if you’re

using a center speaker, the center channel sound is out-

put by only the center speaker. (If you’re not using a

center speaker, the center channel sound will be distrib-

uted to the front left and right speakers to create a phan-

tom center). This setting controls the front left, right,

and center mix, allowing you to adjust the weight of the

center channel sound.

Audio Adjust

With the Audio Adjust functions and settings, you can

adjust the sound and listening modes as you like.

Multiplex/Mono Settings

Multiplex

This setting determines which channel of a stereo multi-

plex source is output. Use it to select audio channels or

languages with multiplex sources, multilingual TV broad-

casts, and so on.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Reference Level

DTS Setting

Audyssey Dynamic EQ™ Reference Level Offset

`0 dB:

Neo:6 Music

It should be used when listening to movies.

`5 dB:

■ Center Image

`0 to 2 to 5

Select this setting for content that has a very wide

dynamic range, such as classical music.

`10 dB:

With this setting, you can specify by how much the

front left and right channel output is attenuated in order

to create the center channel.

Select this setting for jazz or other music that has a

wider dynamic range. This setting should also be

selected for TV content as that is usually mixed at

10 dB below film reference.

Setting a value “0” in the middle is set to hear a sound.

Sound is spread in left and right (the outside) so that the

set value is made big. Please adjust by liking.

`15 dB:

Audyssey Settings

Select this setting for pop/rock music or other pro-

gram material that is mixed at very high listening

levels and has a compressed dynamic range.

Movies are mixed in rooms calibrated for film refer-

ence. To achieve the same reference level in a home the-

ater system each speaker level must be adjusted so that

–30 dBFS band-limited (500 Hz to 2000 Hz) pink noise

produces 75 dB sound pressure level at the listening

position. A home theater system automatically cali-

brated by Audyssey EQ will play at reference level

when the master volume control is set to the 0 dB posi-

tion. At that level you can hear the mix as the mixers

heard it.

Audyssey EQ™ is based on the same core technology as

Audyssey MultEQ that is used for automatic correction

of room acoustics. Audyssey EQ uses time-domain filters

to correct problems that arise from speaker drivers and

enclosures and is calibrated to account for the acoustical

problems in a typical listening environment. The

Audyssey EQ filters in the HT-R380 are specifically opti-

mized for the Onkyo HTP-380 Speaker Package and

should not be used with other speakers.

Audyssey settings cannot be adjusted while Speakers B is

selected.

■ Audyssey

Audyssey Dynamic EQ is referenced to the standard

film mix level. It makes adjustments to maintain the ref-

erence response and surround envelopment when the

volume is turned down from 0 dB. However, film refer-

ence level is not always used in music or other non-film

content. Audyssey Dynamic EQ Reference Level Offset

provides three offsets from the film level reference

(5 dB, 10 dB, and 15 dB) that can be selected when the

mix level of the content is not within the standard.

`Off:

No Audyssey EQ equalizing will apply.

`On:

“Dynamic EQ” and “Dynamic Volume” become

available.

The “Audyssey” indicator will light (➔ 8).

■ Dynamic EQ

`Off:

Audyssey Dynamic EQ off.

`On:

Note

• If “Dynamic EQ” setting is set to “Off”, this setting cannot be

selected.

• The setting is stored individually for each input selector.

Audyssey Dynamic EQ on.

The “Dynamic EQ” indicator will light (➔ 8).

With Audyssey Dynamic EQ™, you can enjoy great

sound even when listening at low volume levels.

Audyssey Dynamic EQ solves the problem of deterio-

rating sound quality as volume is decreased by taking

into account human perception and room acoustics. It

does so by selecting the correct frequency response and

surround volume levels moment-by-moment so that the

content sounds the way it was created at any volume

level — not just at reference level.

■ Dynamic Volume

`Off:

Audyssey Dynamic Volume™ off.

`Light:

Light Compression Mode becomes active.

`Medium:

Medium Compression Mode becomes active.

`Heavy:

Heavy Compression Mode becomes active. This set-

ting affects volume the most, causing all sounds to

be of equal loudness.

Note

• The setting is stored individually for each input selector.

Note

• If you make Dynamic Volume™ active, “Audyssey” and

“Dynamic EQ” settings are set to “On”. The “Dynamic Vol”

indicator will light (➔ 8).

• “Dynamic Volume” setting cannot be set if speakers B are being

used.

• The setting is stored individually for each input selector.

Download from Www.Somanuals.com. All Manuals Search And Download.

About Audyssey Dynamic EQ

Name Edit

Audyssey Dynamic EQ solves the problem of deterio-

rating sound quality as volume is decreased by taking

into account human perception and room acoustics.

Dynamic EQ selects the correct frequency response and

surround levels moment-by-moment at any user-

selected volume setting. The result is bass response,

tonal balance, and surround impression that remain con-

stant despite changes in volume. Dynamic EQ combines

information from incoming source levels with actual

output sound levels in the room, a prerequisite for deliv-

ering a loudness correction solution.

Name Edit

You can enter a preset name for each individual input

selector for easy identification. When entered, the preset

name will appear on the display.

Preparation

Press the input selector buttons to select an input source.

■ Name

`- - -, Blu-ray, DVD, HD DVD, VCR, DVR, Tivo,

CableSTB, SAT STB, PS3, Wii, Xbox, PC, TV, CD,

TAPE, iPod:

Audyssey Dynamic EQ works in tandem with

Audyssey EQ to provide well-balanced sound for every

listener at any volume level.

To reset to the default, select “- - -”.

Note

About Audyssey Dynamic Volume

• Can not set the input selector by the same name.

• This menu cannot be used for the TUNER input selector.

Audyssey Dynamic Volume solves the problem of large

variations in volume level between television programs,

commercials, and between the soft and loud passages of

movies. Dynamic Volume looks at the preferred volume

setting by the user and then monitors how the volume of

program material is being perceived by listeners in real

time to decide whether an adjustment is needed. When-

ever necessary, Dynamic Volume makes the necessary

rapid or gradual adjustments to maintain the desired

playback volume level while optimizing the dynamic

range. Audyssey Dynamic EQ is integrated into

Dynamic Volume so that as the playback volume is

adjusted automatically, the perceived bass response,

tonal balance, surround impression, and dialog clarity

remain the same whether watching movies, flipping

between television channels, or changing from stereo to

surround sound content.

Hardware

Remote Control Settings

■ Remote ID

`1, 2, or 3

When several Onkyo components are used in the same

room, their remote ID codes may overlap. To differenti-

ate the AV receiver from the other components, you can

change its remote ID from “1”, to “2” or “3”.

Note

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you

won’t be able to control it with the remote controller.

Theater-Dimensional Setting

■ Listening Angle

`Wide:

Changing the Remote Controller’s ID

Select if the listening angle is 40 degrees.

`Narrow:

While holding down RECEIVER, press and hold

down SETUP until the remote indicator lights

(about 3 seconds) (➔ 30).

Select if the listening angle is 20 degrees.

With this setting, you can optimize the Theater-Dimen-

sional listening mode by specifying the angle of the

front left and right speakers relative to the listening

position. Ideally, the front left and right speakers should

be equidistant from the listening position and at an

angle close to one of the two available settings.

Use the number buttons to enter ID 1, 2, or 3.

The remote indicator flashes twice.

FM/AM Frequency Setup Settings

For FM/AM tuning to work properly, you must specify the

FM/AM frequency step used in your area. Note that when

this setting is changed, all radio presets will be deleted.

Front left

speaker

Front right

speaker

20°/40°

■ FM/AM Freq Step (North American models)

`200k/10kHz:

Select if 200 k/10 kHz steps are used in your area.

`50k/ 9kHz:

Select if 50 k/9 kHz steps are used in your area.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ AM Freq Step (Asian models)

`10kHz:

Select if 10 kHz steps are used in your area.

`9kHz:

Note

• When set to “On” and close the menu, the name of connected

p-compatible components and “RIHD On” are dis-

played on the AV receiver.

Select if 9 kHz steps are used in your area.

“Search…” → “(name)” → “RIHD On”

When the AV receiver cannot receive the name of the compo-

nent, it is displayed as “Player ” or “Recorder ”, etc (“ ” means

the number of two or more component).

HDMI Setup

When set to “Off” and close the menu, “RIHD Off” are dis-

played on the AV receiver.

HDMI Setup

“Disconnect” → “RIHD Off”

■ Audio TV OUT

`Off:

• When an p-compatible component is connected to the

AV receiver via the HDMI cable, the name of the connected

component is displayed on the AV receiver display. For example,

while you are watching TV broadcasting, if you operate a

Blu-ray Disc/DVD player (being powered on) by the remote

control of the AV receiver, the name of the Blu-ray Disc/DVD

player is displayed on the AV receiver.

• Set to “Off” when a connected piece of equipment is not com-

patible or it is unclear whether the equipment is compatible or

not.

HDMI audio is not output.

`On:

HDMI audio is output.

This preference determines whether audio received at the

HDMI IN is output by the HDMI OUT. You may want to

turn this preference on if your TV is connected to the

HDMI OUT and you want to listen to the audio from a

component that’s connected to an HDMI IN, through your

TV’s speakers. Normally, this should be set to “Off”.

• If movement is unnatural when set to “On”, change the setting

to “Off”.

• Refer to the connected component’s instruction manual for

details.

Note

• If “On” is selected and the signal can be output by the TV, the

AV receiver will output no sound through its speakers.

• If “On” is selected, “TV Sp On” appears on the display by

pressing DISPLAY.

• When “TV Control” is set to “On”, this setting is fixed to

“Auto”.

■ Audio Return Ch (ARC)

`Off:

Select “Off” if you don’t want to use audio return

channel (ARC) function.

`Auto:

• With some TVs and input signals, no sound may be output even

The audio signal from your TV tuner can be sent to

the HDMI OUT of the AV receiver.

Audio return channel (ARC) function enables an HDMI

1.4 capable TV to send the audio stream to the HDMI

OUT of the AV receiver. To use this function, you must

select the TV/CD input selector and your TV must support

ARC function.

when this setting is set to “On”.

• When the “Audio TV OUT” setting is set to “On”, or “TV Con-

trol” is set to “On” and you’re listening through your TV’s

speakers (➔ 16), if you turn up the AV receiver’s volume con-

trol, the sound will be output by the AV receiver’s front left and

right speakers. To stop the AV receiver’s speakers producing

sound, change the settings, change your TV’s settings, or turn

down the AV receiver’s volume.

Note

■ LipSync

`Disable:

• The “Audio Return Ch” setting can be set only when the above

“HDMI Control” setting is set to “On”.

HDMI lip sync disabled.

`Enable:

• This setting is set to “Auto” automatically when the above

“HDMI Control” is set to “On” first time.

HDMI lip sync enabled.

■ Power Control

`Off:

Power Control disabled.

`On:

The AV receiver can be set to automatically correct any

delay between the video and the audio, based on the

data from the connected monitor.

Note

Power Control enabled.

• This function works only if your HDMI-compatible TV supports

HDMI Lip Sync.

• You can check the amount of delay being applied by the HDMI

Lip Sync function on the A/V Sync screen.

To link the power functions of p-compatible

components connected via HDMI, select “On”.

This setting is set to “On” automatically when the

above “HDMI Control” is set to “On” first time.

■ HDMI Control (RIHD)

`Off:

p disabled.

`On:

p enabled.

This function allows p-compatible components

connected via HDMI to be controlled with the AV

receiver (➔ 53 to 55).

Download from Www.Somanuals.com. All Manuals Search And Download.

Note

Using the Audio Settings

• The “Power Control” setting can be set only when the above

“HDMI Control” setting is set to “On”.

You can change various audio settings by pressing

AUDIO.

• HDMI power control only works with p-compatible

components that support it and may not work properly with

some components due to their settings or compatibility.

• When set to “On”, power consumption will increase.

• When set to “On”, regardless of whether the AV receiver is On

or in Standby, both audio and video stream from an HDMI input

will be output to the TV or other components via HDMI connec-

tion (HDMI pass through function). When the HDMI pass

through function activates in standby mode, HDMI THRU indi-

cator will light.

Note

• When the “Audio TV OUT” setting is set to “On” (➔ 36),

AUDIO is disabled.

Press RECEIVER followed by AUDIO.

Use q/w to select an item, and e/r to change the

setting.

• The power consumption during standby mode will increase dur-

ing the HDMI pass through function; however in the following

cases, the power consumption can be saved:

Repeat this step for the other settings.

Tone Control Settings

1. The TV is in standby mode.

2. You are watching a TV program.

• Refer to the connected component’s instruction manual for

details.

You can adjust the bass and treble for Speakers A and B

front speakers, except when the Direct listening mode is

selected.

■ TV Control

`Off:

■ Bass

`–10 dB to 0 dB to +10 dB in 2 dB steps

You can boost or cut low-frequency sounds output

by the front speakers.

TV Control disabled.

`On:

TV Control enabled.

■ Treble

Set to “On” when you want to control the AV receiver

from an p-compatible TV that is connected to

HDMI.

`–10 dB to 0 dB to +10 dB in 2 dB steps

You can boost or cut high-frequency sounds output

by the front speakers.

Note

• Do not assign the component connected with the HDMI input to

the TV/CDselector when you set “TV Control” setting to “On”.

Otherwise, appropriate CEC (Consumer Electronics Control)

operation is not guaranteed.

• Set to “Off” when the TV is not compatible or when it is unclear

whether the TV is compatible or not.

• The “TV Control” setting can be set only when the above

“HDMI Control” and “Power Control” settings are both set

to “On”.

• Refer to the connected component’s instruction manual for

details.

• To bypass the bass and treble tone circuits, select the Direct lis-

tening mode.

• This procedure can also be performed on the AV receiver by

using its TONE, –, and + buttons (➔ 39).

Speaker Levels

You can adjust the volume of each speaker while listening

to an input source.

These temporary adjustments are cancelled when the AV

receiver is set to Standby. To save the setting you made

here, go to “Level Cal (Level Calibration)” (➔ 33) before

setting the AV receiver to Standby.

After changing the settings of the “HDMI Control”,

“Audio Return Ch”, “Power Control”, or “TV Con-

trol”, turn off the power to all connected pieces of

equipment and then turn them on again. Refer to the

User’s Manuals for all connected pieces of equipment.

■ Subwoofer

`–15 dB to 0 dB to +12 dB in 1 dB steps

■ Center

`–12 dB to 0 dB to +12 dB in 1 dB steps

Note

• You cannot use this function while the AV receiver is muted.

• Speakers that are set to “No” or “None” in the “Sp Config

(Speaker Configuration)” (➔ 32) cannot be adjusted.

Download from Www.Somanuals.com. All Manuals Search And Download.

Audyssey Settings

Music Optimizer

The Music Optimizer function enhances the sound quality

of compressed music files. Use it with music files that use

“lossy” compression, such as MP3.

■ Dynamic EQ

■ Dynamic Volume

See “Dynamic EQ” and “Dynamic Volume” of “Audio

Adjust” (➔ 34).

■ M.Optimizer

`Off:

Music Optimizer off.

`On:

EX.BASS

EX.BASS is a technology that have developed by experi-

ments and listening tests to reproduce a natural deeper

bass. When you turn the mode on, you can get dynamic

and deeper presence on your movies and music.

Music Optimizer on.

Note

• The Music Optimizer function only works with PCM digital

audio input signals with a sampling rate below 48 kHz and ana-

log audio input signals. The Music Optimizer is disabled when

the Direct listening mode is selected.

• The setting is stored individually for each input selector.

• The “M.Opt” indicator will light (➔ 8).

■ EX.BASS

`Off:

EX.BASS off.

`On:

EX.BASS on.

CinemaFILTER

Note

With the CinemaFILTER, you can soften overly bright

movie soundtracks, which are typically mixed for repro-

duction in a movie theater.

• The EX.BASS is disabled when the Direct listening mode is

selected.

CinemaFILTER can be used with the following listening

modes: Dolby Digital, Dolby Digital Plus, Dolby TrueHD,

Dolby Pro Logic II Movie, Multichannel, DTS, DTS

Neo:6 Cinema, DTS 96/24, DTS-HD High Resolution,

DTS-HD Master and DTS Express.

Late Night Function

With the Late Night function, you can reduce the dynamic

range of Dolby Digital material so that you can still hear

quiet parts even when listening at low volume levels—

ideal for watching movies late at night when you don’t

want to disturb anyone.

■ Cinema Fltr

`Off:

■ Late Night

CinemaFILTER off.

For Dolby Digital and Dolby Digital Plus sources, the

options are:

`On:

CinemaFILTER on.

`Off:

Note

Late Night function off.

• The CinemaFILTER may not work when used with certain input

sources.

`Low:

Small reduction in dynamic range.

`High:

Large reduction in dynamic range.

For Dolby TrueHD sources, the options are:

`Auto:

The Late Night function is set to “On” or “Off”

automatically.

`Off:

Late Night function off.

`On:

Late Night function on.

Note

• The effect of the Late Night function depends on the material

that you are playing and the intention of the original sound

designer, and with some material there will be little or no effect

when you select the different options.

• The Late Night function can be used only when the input source

is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.

• The Late Night function is set to “Off” when the AV receiver is

set to Standby. For Dolby TrueHD sources, it will be set to

“Auto”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Audio Selector

Digital Input Signal Formats

You can set priorities of audio output when there are both

digital and analog inputs.

The digital input signal formats are available only for the

input sources that you have assigned a digital input jack

(➔ 31).

■ AudioSel

Normally, the AV receiver detects the signal format auto-

matically. However, if you experience either of the follow-

ing issues when playing PCM or DTS material, you can

manually set the signal format to PCM or DTS.

`ARC:

The audio signal from your TV tuner can be sent to

the HDMI OUT of the AV receiver.

With this selection the TV’s audio can be automati-

cally selected as a priority among other assignments.

`HDMI:

Note

• If the beginnings of tracks from a PCM source are cut off, try

setting the format to PCM.

• If noise is produced when fast forwarding or reversing a DTS

CD, try setting the format to DTS.

• The setting is stored individually for each input selector.

• The setting will be reset to “Auto” when you change the setting

in the “Audio Selector” (➔ 39).

This can be selected when HDMI IN has been

assigned as an input source. If both HDMI (HDMI

IN) and digital audio inputs (COAXIAL IN or OPTI-

CAL IN) have been assigned, HDMI input is auto-

matically selected as a priority.

`COAX:

This can be selected when COAXIAL IN has been

assigned as an input source. If both coaxial and opti-

cal inputs have been assigned, coaxial input is auto-

matically selected as a priority.

Press RECEIVER, and then press and hold

AUDIO for about 8 seconds.

While “Auto” lights (about 3 seconds), press e/r

`OPT:

to select:

This can be selected when OPTICAL IN has been

assigned as an input source.

`Analog:

`Auto:

The format is detected automatically. If no dig-

ital input signal is present, the corresponding

analog input is used instead.

`PCM:

The AV receiver always outputs analog signals.

Note

Only 2-channel PCM format input signals will

be heard. If the input signal is not PCM, the

PCM indicator will flash and noise may also be

produced.

• The setting is stored individually for each input selector.

• This setting can be made only for the input source that is

assigned as HDMI IN, COAXIAL IN, or OPTICAL IN. If both

HDMI (HDMI IN) and digital audio inputs (COAXIAL IN or

OPTICAL IN) are assigned, HDMI input will be selected as a

priority by setting to “ARC” (➔ 36). To select the digital audio

input, see “Digital Audio (Digital Audio Input)” (➔ 31).

`DTS:

Only DTS (but not DTS-HD) format input sig-

nals will be heard. If the input signal is not

DTS, the DTS indicator will flash and there

will be no sound.

You can select “ARC” if you select the TV/CD input selector.

But you cannot select it if you’ve selected “Off” in the “Audio

Return Ch” setting (➔ 36).

A/V Sync

Adjusting the Bass & Treble

When using progressive scanning on your Blu-ray Disc/

DVD player, you may find that the picture and sound are

out of sync. With this setting, you can correct this by

delaying the audio signals.

You can adjust the bass and treble for Speakers A and B

front speakers, except when the Direct listening mode is

selected.

Press TONE on the AV receiver repeatedly to

select either “Bass” or “Treble”.

■ A/V Sync

`0 ms to 100 ms in 10 ms steps

Use TONE –/+ on the AV receiver to adjust.

Note

• A/V Sync is disabled when the Direct listening mode is used

with an analog input source.

■ Bass

• The setting is stored individually for each input selector.

■ Treble

See “Bass” and “Treble” of “Tone Control Settings”

(➔ 37).

Note

• To bypass the bass and treble tone circuits, select the Direct lis-

tening mode.

• This procedure can also be performed on the remote controller

by using TONE, –, and + buttons (➔ 10).

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling iPod

Connecting an Onkyo Dock

No. Onkyo Dock

Cable

Note

Page

UP-A1 Dock

(Universal Port Option Dock)

—

• When UP-A1 Dock that seated iPod is (➔ 41)

connected, the power consumption on

standby mode slightly increases.

• You can control your iPod when

“PORT” is selected as the input source.

• See the UP-A1 Dock’s instruction man-

ual for more information.

RI Dock

Analog audio (RCA)

• See the RI Dock’s instruction manual (➔ 41)

for more information.

To use u (Remote Interactive), you

must make an analog audio connec-

tion (RCA) between the AV receiver

and the RI Dock.

Component video

P^B/CB

PR/CR

Composite video

u cable

Models sold are different depending on the region.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Using Your iPod models Alarm Clock

You can use your iPod models Alarm Clock function to

automatically turn on your iPod and the AV receiver at a

specified time. The AV receiver’s input source will auto-

matically be set to the PORT selector.

Using the Onkyo Dock

Dock is sold separately.

For the latest information on the Onkyo Dock compo-

nents, see the Onkyo web site at:

Note

http://www.onkyo.com

• To use this function, your iPod must be in the UP-A1 Dock, and

the UP-A1 Dock must be connected to the AV receiver.

• This function only works when the Standard mode is set to On.

• When you use this function, be sure to set the AV receiver’s vol-

ume control to a suitable level.

Before using the Onkyo Dock components, update

your iPod with the latest software, available from the

Apple web site.

For supported iPod models, see the instruction man-

ual of the Onkyo Dock.

• You cannot use this function for sound effects on your iPod.

■ Charging Your iPod models Battery

UP-A1 Dock

The UP-A1 Dock charges your iPod models battery while

your iPod is in the UP-A1 Dock and connected to the

UNIVERSAL PORT jack on the AV receiver. While your

iPod is seated in the UP-A1 Dock, its battery will be

charged when the AV receiver is set to “On” or “Standby”.

With the UP-A1 Dock, you can easily play the music,

photo, or movie stored on your Apple iPod through the AV

receiver and enjoy great sound.

You can use the AV receiver’s remote controller to operate

your iPod.

Note

■ Basic Operation

• When UP-A1 Dock that seated iPod is connected, the power

consumption on standby mode slightly increases.

The AV receiver may take several seconds to startup, so

you might not hear the first few seconds of the first

song.

■ Status Messages

• PORT Reading

The AV receiver is checking the connection with the

dock.

• PORT Not Support

The AV receiver do not support the connected dock.

• PORT UP-A1

UP-A1 Dock is connected.

Auto Power On

If you start iPod playback while the AV receiver is on

Standby, the AV receiver will automatically turn on and

select your iPod as the input source.

Direct Change

Note

If you start iPod playback while listening to another input

source, the AV receiver will automatically select your iPod

as the input source.

• The AV receiver displays the message “UP-A1” for several sec-

onds after recognizing the UP-A1.

• When the status message is not displayed on the AV receiver’s

display, check the connection to your iPod.

Using the AV receiver’s Remote Controller

You can use the AV receiver’s remote controller to control

basic iPod functions (➔ 42).

RI Dock

With the RI Dock, you can easily play the music stored on

your Apple iPod through the AV receiver and enjoy great

sound, and watch iPod slideshows and videos on your TV.

In addition, the onscreen display (OSD) allows you to

view, navigate, and select your iPod’s contents on your

TV, and with the supplied remote controller, you can con-

trol your iPod from the comfort of your sofa. You can even

use the AV receiver’s remote controller to operate your

iPod.

■ Operating Notes

• Functionality depends on your iPod model and generation.

• Before selecting a different input source, stop iPod playback

to prevent the AV receiver from selecting the iPod input

source by mistake.

• If any accessories are connected to your iPod, the AV receiver

may not be able to select the input source properly.

• When connecting UP-A1 Dock to the radio tuner UP-HT1

(North American models)/UP-DT1 (Asian models) with

AUTO selected by the tuner’s Mode Selector switch, you can

switch the input source between UP-A1 Dock and the tuner,

by pressing PORT repeatedly on the front panel.

• While your iPod is in the UP-A1 Dock, its volume control has

no effect. If you adjust your iPod models volume control while

it’s in the UP-A1 Dock, make sure it’s not set too high before

you reconnect your headphones.

• The Auto Power On function will not work if you set your

iPod in the UP-A1 Dock while it is playing.

• Do not turn off the power with the iPod still connected to this

unit via the UP-A1 Dock.

• Set your iPod in the UP-A1 Dock after the AV receiver turns

on.

Download from Www.Somanuals.com. All Manuals Search And Download.

Note

Controlling Y o ur iPod

• Enter the appropriate remote control code before using the AV

receiver’s remote controller for the first time (➔ 44).

• Connect the RI Dock to the AV receiver with an u cable

(➔ 40).

By pressing REMOTE MODE that’s been programmed

with the remote control code for your Dock, you can con-

trol your iPod in the Dock with the following buttons.

See “Remote Control Codes for Onkyo Components Con-

nected via u” for details on entering a remote control

code (➔ 44).

• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/

DOCK”.

• Set the AV receiver’s Input Display to “DOCK” (➔ 22).

See to the Dock’s instruction manual for more informa-

tion.

■ System Function

System On

When you turn on the AV receiver, the RI Dock and iPod

turn on automatically. In addition, when the RI Dock and

iPod are on, the AV receiver can be turned on by pressing

ON/STANDBY.

■ UP-A1 Dock

PORT is preprogrammed with the remote control code for

controlling a Dock with Universal Port connector.

You can control your iPod when “PORT” is selected as

the input source.

Auto Power On

If you press the remote controller’s 1 while the AV

receiver is on Standby, the AV receiver will automatically

turn on, select your iPod as the input source, and your

iPod will start playback.

Without the RI Control

You must enter a remote control code 82990 first (➔ 44).

Direct Change

■ RI Dock

If you start iPod playback while listening to another input

source, the AV receiver will automatically switch to the

input to which the RI Dock is connected.

Other Remote Controllers

You can use the remote controller that came with the AV

receiver to control other iPod functions. The available

functionality depends on the AV receiver.

iPod Alarm

• Set the RI Dock’s RI MODE switch to “HDD” or

“HDD/DOCK”.

• ON/STANDBY may not work with a remote control

code (without u). In this case, make an u connection

and enter a remote control code 82351 (with u).

With the RI Control

In this case, make an u connection and enter a remote

control code 82351 (with u).

If you use the Alarm function on your iPod to start play-

back, the AV receiver will turn on at the specified time and

select your iPod as the input source automatically.

• Set the AV receiver’s Input Display to “DOCK” (➔ 22).

Note

• Linked operations do not work with video playback or when the

alarm is set to play a sound.

• If you use your iPod with any other accessories, iPod playback

detection may not work.

• This function only works when the Standard mode is set to On.

■ Operating Notes

• Use the AV receiver’s volume control to adjust the playback

volume.

• While your iPod is inserted in the RI Dock, its volume control

has no effect.

• If you do adjust the volume control on your iPod while it’s

inserted in the RI Dock, be careful that it’s not set too loud

before you reconnect your earphones.

Download from Www.Somanuals.com. All Manuals Search And Download.

✔: Available buttons

PresstheappropriateREMOTE

MODE first.

Onkyo Dock

Buttons

✔

ON/STANDBY 9

TOP MENU^*5

✔

q/w/e/r ENTER

PLAYLIST e/r

1, 3, 2, 5,

4, 7, 6

REPEAT

✔

RANDOM

PLAY MODE

DISPLAY^*6

MUTING

ALBUM +/–

VOL q/w

RETURN

✔

Note

• With some iPod models and generations, certain buttons may not work as expected.

• For detailed operation of the iPod, please refer to the instruction manual.

This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on or off. Your iPod may not respond the first time you press this

button, in which case you should press it again.

This is because the remote controller transmits the On and Standby commands alternately, so if your iPod is already on, it will

remain on when the remote controller transmits an On command.

Similarly, if your iPod is already off, it will remain off when the remote controller transmits an Off command.

Press DISPLAY to change the following modes:

Standard mode

Nothing is displayed on your TV and you navigate and select your contents by using your iPod models display.

Only this mode can playback the video.

Extended mode

Playlists (artists, albums, songs, and so on) are displayed on your TV, and you can navigate and select your music while looking at

your TV.

In Extended mode (see ), PLAYLIST is used as the page jump button.

With the page modes, you can quickly locate your favorite songs even when your song lists, artist lists, and so on are very long.

Resume mode

With the Resume function, you can resume playback of the song that was playing when you removed your iPod from the RI Dock or

changed the OSD mode to Off.

TOP MENU works as a Mode button when used with a DS-A2 RI Dock.

DISPLAY turns on backlight for 30 seconds.

Note

• In Extended mode (see ), the playback will be continued even if the AV receiver is turned off.

• In Extended mode (see ), you cannot operate your iPod directly.

• In Extended mode (see ), it may take some time to acquire the contents.

• In Extended mode (see ), video contents can not display on your TV.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling Other Components

You can use the AV receiver’s remote controller

Remote Control Codes for Onkyo

(RC-762M) to control your other AV components. This

section explains how to enter the remote control code for a

component that you want to control: DVD, TV, CD, etc.

Components Connected via u

Onkyo components that are connected via u are con-

trolled by pointing the remote controller at the AV

receiver, not the component. This allows you to control

components that are out of view, in a rack, for example.

Preprogrammed Remote Control

Codes

The following REMOTE MODE are preprogrammed

with remote control codes for controlling the components

listed. You do not need to enter a remote control code to

control these components.

For details on controlling these components, see the pages

indicated.

Make sure the Onkyo component is connected

with an u cable and an analog audio cable

(RCA).

See “Connecting Onkyo u Components” for

details (➔ 18).

Enter the appropriate remote control code for

BD/DVD

TV/CD

PORT

Onkyo Blu-ray Disc player (➔ 45)

Onkyo CD player (➔ 45)

Onkyo Universal Port Option Dock (➔ 42)

REMOTE MODE.

• BD/DVD

`31612:

Onkyo DVD player with u

• TV/CD

`71323:

Entering Remote Control Codes

You’ll need to enter a code for each component that you

want to control.

Onkyo CD player with u

`42157:

Onkyo cassette tape deck with u

• PORT

Look up the appropriate remote control code in

the Remote Control Codes for Onkyo Compo-

`82351:

nents Connected via u.

Onkyo Universal Port Option Dock

• TUNER

`51805:

Onkyo AV receiver’s tuner

See the previous section for how to enter remote

control codes.

While holding down REMOTE MODE to which

you want to enter a code, press and hold down

DISPLAY (about 3 seconds).

Note

• Remote control codes cannot be entered for RECEIVER.

• Apart from RECEIVER, remote control codes from any

category can be entered for REMOTE MODE. However,

these buttons also work as input selector buttons (➔ 21),

so choose a REMOTE MODE that corresponds with the

input to which you connect your component. For example,

if you connect your CD player to the CD input, choose

TV/CD when entering its remote control code.

Note

• When using a cassette tape deck connected via u, press

and hold TV/CD to switch to TAPE.

Press REMOTE MODE, point the remote control-

ler at the AV receiver, and operate the component.

Within 30 seconds, use the number buttons to

enter the 5-digit remote control code.

The remote indicator flashes twice.

If the remote control code is not entered success-

fully, the remote indicator will flash once slowly.

If you want to control an Onkyo component by pointing

the remote controller directly at it, or you want to control

an Onkyo component that’s not connected via u, use the

following remote control codes:

• BD/DVD

`30627:

Onkyo DVD player without u

• TV/CD

`71817:

Onkyo CD player without u

`11807:

Onkyo TV

Download from Www.Somanuals.com. All Manuals Search And Download.

If you want to control an Onkyo component by pointing the

remote controller directly at it, use the following remote

Controlling Other Components

control codes:

`32900:

By pressing REMOTE MODE that’s been programmed

with the remote control code for your component, you can

control Onkyo component as below.

Onkyo Blu-ray Disc player

`32901:

Onkyo HD-DVD player

`70868:

For details on entering a remote control code for a differ-

ent component (➔ 44).

Controlling a Blu-ray Disc/DVD Player, HD

DVD Player or DVD Recorder

Onkyo MD recorder

`71323:

Onkyo CD recorder

`82990:

BD/DVD is preprogrammed with the remote control code

for controlling a component that supports the p.

The component must be able to receive remote control

commands via p and be connected to the AV

receiver via HDMI.

Onkyo Universal Port Option Dock

Note

• If you connect an cassette tape deck to the TV/CD IN jacks, or

connect an RI Dock to the TV/CD IN or VCR/DVR IN or

GAME IN jacks, for u to work properly, you must set the Input

Display accordingly (➔ 22).

Resetting REMOTE MODE Buttons

You can reset a REMOTE MODE to its default remote

control code.

While holding down REMOTE MODE that you

want to reset, press and hold down AUDIO until

the remote indicator lights (about 3 seconds).

Within 30 seconds, press REMOTE MODE again.

The remote indicator flashes twice, indicating that

the button has been reset.

Each of REMOTE MODE is preprogrammed with a

remote control code. When a button is reset, its pre-

programmed code is restored.

Resetting the Remote Controller

You can reset the remote controller to its default settings.

While holding down RECEIVER, press and hold

down AUDIO until the remote indicator lights

(about 3 seconds).

Within 30 seconds, press RECEIVER again.

The remote indicator flashes twice, indicating that

the remote controller has been reset.

Download from Www.Somanuals.com. All Manuals Search And Download.

✔: Available buttons

PresstheappropriateREMOTE

MODE first.

Components

Buttons

ON/STANDBY

✔

✔ ✔

✔

GUIDE

TOP MENU

✔

✔ ✔

q/w/e/r

ENTER

SETUP

✔

✔ ✔

✔

1, 3, 2, 5,

4, 7, 6

*1*2

✔

*1*2

✔

*1*2

✔

*1*2

✔

REPEAT

✔

RANDOM

PLAY MODE

✔

Number: 1 to 9, 0 ✔

✔ ✔

Number: +10

DISPLAY

MUTING

DISC +/–

PREV CH

✔

✔ ✔

✔

RETURN

AUDIO

✔

✔ ✔

✔

CLR

✔ ✔

✔

The p function is not supported. The p sup-

ported by the AV receiver is the CEC system control function

of the HDMI standard.

These buttons functions as colored buttons or A, B, C, D but-

tons.

3 (Pause) functions as reverse playback.

Note

• See the “Controlling Your iPod” about the operation of iPod

(➔ 42).

Note

• With some components, certain buttons may not work as

expected, and some may not work at all.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

If you have any trouble using the AV receiver, look for a

solution in this section. If you can’t resolve the issue your-

self, contact your Onkyo dealer.

■ The STANDBY indicator flashes red

The protection circuitry has been activated.

Remove the power cord from the wall outlet immedi-

ately. Disconnect all speaker cables and input

sources, and then leave the AV receiver with its

power cord disconnected for 1 hour. After that,

reconnect the power cord and set the volume to max-

imum. If the AV receiver stays on, set then the vol-

ume to minimum, disconnect the power cord, and

reconnect your speakers and input sources. If the AV

receiver turns off when you set the volume to maxi-

mum, disconnect the power cord, and contact your

Onkyo dealer.

—

If you can’t resolve the issue yourself, try resetting the

AV receiver before contacting your Onkyo dealer.

To reset the AV receiver to its factory defaults, turn it

on and, while holding down VCR/DVR, press ON/

STANDBY. “Clear” will appear on the display and

the AV receiver will enter Standby mode.

Audio

■ There’s no sound, or it’s very quiet

Note that resetting the AV receiver will delete your

radio presets and custom settings.

Press SPEAKERS A or B to turn on the indicator

—

for the speakers that you want to output sound.

Make sure that the digital input source is selected

properly.

Remote indicator

Make sure that all audio connecting plugs are pushed 15

in all the way.

Make sure that the inputs and outputs of all compo- 16-18

nents are connected properly.

RECEIVER

AUDIO

Make sure that the polarity of the speaker cables is 12

correct, and that the bare wires are in contact with

the metal part of each speaker terminal.

Make sure that the input source is properly selected. 21

Make sure that the speaker cables are not shorting. 12

Check the volume. The AV receiver is designed for

home theater enjoyment. It has a wide volume range,

allowing precise adjustment.

—

To reset the remote controller to its factory defaults,

while holding down RECEIVER, press and hold down

AUDIO until the remote indicator lights (about 3 sec-

onds). Within 30 seconds, press RECEIVER

again.

If the MUTING indicator is flashing on the display, 22

press the remote controller’s MUTING to unmute

the AV receiver.

While a pair of headphones is connected to the

PHONES jack, no sound is output by the speakers.

If there’s no sound from a DVD player connected to

an HDMI IN, check the DVD player’s output set-

tings, and be sure to select a supported audio format.

—

The on-screen setup menus appear only on a TV that

is connected to the HDMI OUT. If your TV is con-

nected to the MONITOR OUT V or the COMPO-

NENT VIDEO OUT, use the AV receiver’s display

when changing settings.

Check the digital audio output setting on the con-

nected device. On some game consoles, such as

those that support DVD, the default setting is off.

—

With some DVD-Video discs, you need to select an

audio output format from a menu.

—

If your turntable uses an MC cartridge, you must

connect an MC head amp, or an MC transformer.

Power

Make sure that none of the connecting cables are

bent, twisted, or damaged.

■ Can’t turn on the AV receiver

Make sure that the power cord is properly plugged

into the wall outlet.

—

Not all listening modes use all speakers.

Specify the speaker distances and adjust the individ- 32

ual speaker levels.

Unplug the power cord from the wall outlet, wait five

seconds or more, then plug it in again.

The input signal format is set to PCM or DTS. Set it 39

to Auto.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ Only the front speakers produce sound

■ Noise can be heard

Using cable ties to bundle audio cables with power

cords, speaker cables, and so on may degrade the

audio performance, so don’t do it.

—

When the Stereo or Mono listening mode is selected,

only the front speakers and subwoofer produce

sound.

—

An audio cable may be picking up interference. Try

repositioning your cables.

Check the Speaker Configuration.

■ Only the center speaker produces sound

■ The Late Night function doesn’t work

If you use the Dolby Pro Logic II Movie, Dolby Pro

Logic II Music, or Dolby Pro Logic II Game listen-

ing mode with a mono source, such as an AM radio

station or mono TV program, the sound is concen-

trated in the center speaker.

—

Make sure the source material is Dolby Digital,

Dolby Digital Plus, and Dolby TrueHD.

■ About DTS signals

Make sure the speakers are configured correctly.

When DTS program material ends and the DTS bit-

stream stops, the AV receiver remains in DTS listen-

ing mode and the DTS indicator remains on. This is

to prevent noise when you use the pause, fast for-

ward, or fast reverse function on your player. If you

switch your player from DTS to PCM, because the

AV receiver does not switch formats immediately,

you may not hear any sound, in which case you

should stop your player for about three seconds, and

then resume playback.

—

■ The surround speakers produce no sound

When the T-D (Theater-Dimensional), Stereo or

Mono listening mode is selected, the surround

speakers produce no sound.

—

Depending on the source and current listening mode,

not much sound may be produced by the surround

speakers. Try selecting another listening mode.

—

With some CD and LD players, you won’t be able to

playback DTS material properly even though your

player is connected to a digital input on the AV

receiver. This is usually because the DTS bitstream

has been processed (e.g., output level, sampling rate,

or frequency response changed) and the AV receiver

doesn’t recognize it as a genuine DTS signal. In such

cases, you may hear noise.

—

Make sure the speakers are configured correctly.

■ The center speaker produces no sound

When the Stereo or Mono listening mode is selected,

the center speaker produces no sound.

—

Make sure the speakers are configured correctly.

When playing DTS program material, using the

pause, fast forward, or fast reverse function on your

player may produce a short audible noise. This is not

a malfunction.

■ The subwoofer produces no sound

The subwoofer outputs no sound while only Speak- 11

ers B is on. Turn on Speakers A.

When you play source material that contains no

information in the LFE channel, the subwoofer pro-

duces no sound.

—

■ The beginning of audio received by an HDMI IN

can’t be heard

Make sure the speakers are configured correctly.

Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio sig-

nals, audio output may not start immediately.

—

■ There’s no sound with a certain signal format

Check the digital audio output setting on the con-

nected device. On some game consoles, such as

those that support DVD, the default setting is off.

—

Video

With some DVD-Video discs, you need to select an

audio output format from a menu.

—

■ There’s no picture

Make sure that all video connecting plugs are pushed 15

in all the way.

Depending on the input signal, some listening modes 27–29

cannot be selected.

Make sure that each video component is properly

connected.

16, 17

17, 31

■ Can’t get 5.1 playback

If the video source is connected to a component

video input, you must assign that input to an input

selector, and your TV must be connected to COM-

PONENT VIDEO MONITOR OUT.

When speaker B is turned on, Speakers A is reduced 11

to 2.1 channel playback.

You can not always select all of the listening modes, 27–29

depending on the number of the speakers connected.

If the video source is connected to a composite video 17

input, your TV must be connected to the correspond-

ing composite video output.

■ The volume cannot be set to 79

If the video source is connected to an HDMI input, 16, 31

you must assign that input to an input selector, and

your TV must be connected to the HDMI OUT.

After the volume level of each individual speaker has 33

been adjusted, the maximum volume may be

reduced.

On your TV, make sure that the video input to which

the AV receiver is connected is selected.

—

Download from Www.Somanuals.com. All Manuals Search And Download.

■ There’s no picture from a source connected to

an HDMI IN

If you’ve connected a cassette tape deck, to the TV/ 22

CD IN jacks, or an RI Dock to the TV/CD IN or

GAME IN or VCR/DVR IN jacks, for the remote

controller to work properly, you must set the display.

Reliable operation with an HDMI-to-DVI adapter is 54

not guaranteed. In addition, video signals from a PC

are not guaranteed.

If you cannot operate it, you will need to enter the

appropriate remote control code.

To control an Onkyo component that’s connected via 44

u, point the remote controller at the AV receiver.

Be sure to enter the appropriate remote control code

first.

To control an Onkyo component that’s not connected 44

via u, point the remote controller at the compo-

nent. Be sure to enter the appropriate remote control

code first.

■ The on-screen menus don’t appear

On your TV, make sure that the video input to which

the AV receiver is connected is selected.

—

When the AV receiver doesn’t connect TV with

HDMI, onscreen menus are not displayed.

Tuner

■ Reception is noisy, FM stereo reception is

noisy, or the FM STEREO indicator doesn’t light

UP-A1 Dock for iPod

■ There’s no sound

Relocate your antenna.

—

Make sure your iPod is actually playing.

—

Move the AV receiver away from your TV or com-

puter.

Make sure your iPod is inserted properly in the

Dock.

Listen to the station in mono.

Make sure the UP-A1 Dock is connected to the UNI- —

VERSAL PORT jack on the AV receiver.

When listening to an AM station, operating the

remote controller may cause noise.

—

Make sure the AV receiver is turned on, the correct

input source is selected, and the volume is turned up.

—

Passing cars and airplanes can cause interference.

Concrete walls weaken radio signals.

—

Make sure the plugs are pushed in all the way.

Try resetting your iPod.

—

If nothing improves the reception, install an outdoor

antenna.

■ There’s no video

Remote Controller

Make sure that your iPod’s TV OUT setting is set to

On.

—

■ The remote controller doesn’t work

Make sure the correct input is selected on your TV or

the AV receiver.

Before operating this unit, be sure to press

RECEIVER.

—

Some versions of the iPod do not output video.

Make sure that the batteries are installed with the

correct polarity.

■ The AV receiver’s remote controller doesn’t

control your iPod

Install new batteries. Don’t mix different types of

batteries, or old and new batteries.

Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the

AV receiver’s remote control sensor.

Make sure your iPod is properly inserted in the

Dock. If your iPod is in a case, it may not connect

properly to the Dock. Always remove your iPod

from the case before inserting it into the Dock.

—

Make sure that the AV receiver is not subjected to

direct sunshine or inverter-type fluorescent lights.

Relocate if necessary.

—

The iPod cannot be operated while it’s displaying the

Apple logo.

—

Make sure you’ve selected the right remote mode.

—

If the AV receiver is installed in a rack or cabinet

with colored-glass doors, the remote controller may

not work reliably when the doors are closed.

When you use the AV receiver’s remote controller,

point it toward your AV receiver.

When connecting UP-A1 Dock to the radio tuner

UP-HT1 (North American models)/UP-DT1

(Asian models) with AUTO selected by the tuner's

Mode Selector switch, you can switch the input

source between UP-A1 Dock and the tuner, by press-

ing PORT repeatedly on the front panel.

—

Make sure you’ve selected the correct remote con- 10, 45

troller mode.

Make sure you’ve entered the correct remote control 44

code.

Make sure to set the same ID on both the AV receiver 35

and remote controller.

If you still can’t control your iPod, start playback by

pressing your iPod’s Play button. Remote operation

should then be possible.

—

■ Can’t control other components

Try resetting your iPod.

—

If it’s an Onkyo component, make sure that the u

Depending on your iPod, some buttons may not

work as expected.

cable and analog audio cable are connected properly.

Connecting only an u cable won’t work.

Make sure you’ve selected the correct remote con- 10, 45

troller mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ The AV receiver unexpectedly selects your iPod

as the input source

The AV receiver contains a microcomputer for signal

processing and control functions. In very rare situations,

severe interference, noise from an external source, or

static electricity may cause it to lockup. In the unlikely

event that this happens, unplug the power cord from the

wall outlet, wait at least five seconds, and then plug it

back in again.

Always pause iPod playback before selecting a dif-

ferent input source. If playback is not paused, the

Direct Change function may select your iPod as the

input source by mistake during the transition

between tracks.

—

Recording

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

the unit’s malfunction. Before you record important

data, make sure that the material will be recorded cor-

rectly.

■ Can’t record

On your recorder, make sure the correct input is

selected.

—

To prevent signal loops and damage to the AV

receiver, input signals are not fed through to outputs

with the same name (e.g., VCR/DVR IN to VCR/

DVR OUT).

Before disconnecting the power cord from the wall out-

let, set the AV receiver to Standby.

Others

■ The sound changes when I connect my

headphones

When a pair of headphones is connected, the listen-

ing mode is set to Stereo, unless it’s already set to

Stereo, Mono, or Direct.

—

■ How do I change the language of a multiplex

source

Use the “Multiplex” setting on the “Audio Adjust” 33

menu to select “Main” or “Sub”.

■ The u functions don’t work

To use u, you must make an u connection and an

analog audio connection (RCA) between the compo-

nent and AV receiver, even if they are connected dig-

itally.

■ The following settings can be made for the

composite video inputs

You must use the buttons on the unit to make these set-

tings.

1. While holding down the input selector button for the input

source that you want to set, press SETUP.

2. Use e/r to change the setting.

3. Press the input selector button for the input source that you

want to set when you’ve finished.

• Video Attenuation

This setting can be made for the BD/DVD, VCR/DVR,

CBL/SAT, GAME, or AUX input.

If you have a games console connected to the composite

video input, and the picture isn’t very clear, you can

attenuate the gain.

Video ATT:OFF: (default).

Video ATT:ON: Gain is reduced by 2 dB.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

AV Receiver

Amplifier Section

General

Rated Output Power

All channels:

Power Supply

(North American) AC 120 V, 60 Hz

(Others) AC 220 - 240 V, 50/60 Hz

(North American)

110 watts minimum continuous power

per channel, 6 ohms, at 1 kHz with a

maximum total harmonic distortion of

Power Consumption (North American) 3.6 A

(Others) 390 W

Stand-by Power Consumption

(North American) 0.2 W

(Others) 0.3 W

(Others)

^{1 ch}× 100 W at 6 ohms, 1 kHz, 1 ch driven

Dimensions

(W × H × D)

435 mm × 151.5 mm × 328.5 mm

17-1/8" × 5-15/16" × 12-15/16"

(IEC)

Maximum Effective Output Power

(Asian)

Weight

8.0 kg (17.6 lbs.)

^{1 ch}× 120 W at 6 ohms, 1 kHz, 1 ch driven

■ HDMI

(JEITA)

Dynamic Power

160 W (3 Ω, Front)

125 W (4 Ω, Front)

85 W (8 Ω, Front)

Input

Output

IN 1, IN 2, IN 3

OUT

Video Resolution

Audio Format

1080p

THD (Total Harmonic Distortion)

0.08% (1 kHz, 1 W)

60 (Front, 1 kHz, 8 Ω)

Input Sensitivity and Impedance

200 mV/47 kΩ (LINE)

Output Level and Impedance

200 mV/2.2 kΩ (REC OUT)

Dolby TrueHD, DTS Master Audio,

DVD-Audio, DSD

Damping Factor

Supported

3D, Audio Return Channel, Deep Color,

x.v.Color, LipSync, CEC

■ Video Inputs

Frequency Response 20 Hz - 50 kHz/+1 dB, -3 dB (DSP bypass)

Tone Control Characteristies

Component

Composite

IN 1, IN 2

BD/DVD, VCR/DVR, CBL/SAT, GAME

10 dB, 50 Hz (BASS)

10 dB, 20 kHz (TREBLE)

■ Video Outputs

Signal to Noise Ratio 100 db (LINE, IHF-A)

Component

Composite

OUT

Speaker Impedance

6 Ω - 16 Ω

MONITOR OUT, VCR/DVR OUT

Video Section

■ Audio Inputs

Digital

Input Sensitivity/Output Level and Impedance

Optical: 2

Coaxial: 1

1 Vp-p/75 Ω (Component Y)

0.7 Vp-p/75 Ω (Component P^B/CB, PR/CR)

Analog

BD/DVD, VCR/DVR, CBL/SAT, GAME,

TV/CD, AUX

1 Vp-p/75 Ω (Composite)

Component Video Frequency Response

5 Hz - 100 MHz/+0 dB, -3 dB

■ Audio Outputs

Tuner Section

Analog

Speaker Outputs

Phones

VCR/DVR

SP-A (L, R), C, SL, SR + SP-B (L, R), SW

1 (6.3 ø)

FM Tuning Frequency Range

(North American) 87.5 MHz - 107.9 MHz

(Others) 87.50 MHz - 108.00 MHz, RDS

AM Tuning Frequency Range

■ Others

Universal Port

522/530 kHz - 1611/1710 kHz

Preset Channel

Specifications and features are subject to change

without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

5.1ch Home Theater Speaker Package

Passive Subwoofer (SKW-380)

(Asian) Center Speaker (SKC-380C)

Type

Bass-reflex type Passive subwoofer

Type

Full-Range Bass-reflex

Impedance

6Ω

Impedance

6Ω

Maximum input power 130 W

Maximum input power 120 W

Output sound pressure level

83 dB/W/m

85 dB/W/m

Frequency response

Cabinet capacity

30 Hz–150 Hz

Frequency response

Cabinet capacity

80 Hz–20 kHz

0.88 cubic feet (25 L)

0.064 cubic feet (1.8 L)

Dimensions

(W × H × D)

11-5/8" × 13-9/16" × 14-1/2"

(295 × 345 × 368 mm)

Dimensions

(W × H × D)

10-3/4" × 4" × 4-3/16"

(273 × 101 × 106 mm)

Weight

Drivers unit

Terminal

14.1 lbs. (6.4 kg)

Weight

3.1 lbs. (1.4 kg)

3-1/4" (8 cm) Cone × 2

Spring type color coded

8" (20 cm) Cone

Drivers unit

Terminal

Keyhole slot

Grille

Spring type color coded

Front Speaker (SKF-380)

Fixed

Other

Magnetic shielding

Type

Impedance

Full-Range Bass-reflex

6Ω

Surround Speaker (SKR-380)

Maximum input power 120 W

Output sound pressure level

Type

Full-Range Bass-reflex

82 dB/W/m

Impedance

6Ω

Frequency response

Cabinet capacity

80 Hz–20 kHz

Maximum input power 120 W

Output sound pressure level

0.064 cubic feet (1.8 L)

Dimensions

4" × 10-3/4" × 4-3/4"

81 dB/W/m

(W × H × D)

(101 × 273 × 121 mm)

Frequency response

Cabinet capacity

Dimensions

(W × H × D)

80 Hz–20 kHz

Weight

2.2 lbs. (1.0 kg)

3-1/4" (8 cm) Cone

Spring type color coded

0.039 cubic feet (1.1 L)

Drivers unit

Terminal

Keyhole slot

Grille

4" × 6-7/8" × 4-9/16"

(101 × 175 × 116 mm)

1.5 lbs. (0.7 kg)

3-1/4" (8 cm) Cone

Spring type color coded

Weight

Fixed

Drivers unit

Terminal

Keyhole slot

Grille

Other

Magnetic shielding

(North American) Center Speaker (SKC-380)

Fixed

Type

Full-Range Bass-reflex

Impedance

6Ω

Maximum input power 120 W

Output sound pressure level

Specifications and features are subject to change

without notice.

82 dB/W/m

Frequency response

Cabinet capacity

80 Hz–20 kHz

0.064 cubic feet (1.8 L)

Dimensions

(W × H × D)

10-3/4" × 4" × 4-3/16"

(273 × 101 × 106 mm)

Weight

2.2 lbs. (1.0 kg)

3-1/4" (8 cm) Cone

Spring type color coded

Drivers unit

Terminal

Keyhole slot

Grille

Fixed

Other

Magnetic shielding

Download from Www.Somanuals.com. All Manuals Search And Download.

About HDMI

Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital

interface standard for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video compo-

nents. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a

single cable can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichan-

nel digital audio, and multichannel PCM).

The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface) , so TVs and displays with

a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and displays,

resulting in no picture.)

The AV receiver uses HDCP (High-bandwidth Digital Content Protection) , so only HDCP-compatible components can

display the picture.

The AV receiver’s HDMI interface is based on the following:

Audio Return Channel, 3D, x.v.Color, Deep Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution

Audio, Dolby TrueHD, Dolby Digital Plus, DSD and Multichannel PCM

Supported Audio Formats

• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)

• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz, 16/20/24 bit)

• Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution Audio, DTS-HD

Master Audio)

Your Blu-ray Disc/DVD player must also support HDMI output of the above audio formats.

About Copyright Protection

The AV receiver supports HDCP (High-bandwidth Digital Content Protection) , a copy-protection system for digital

video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.

DVI (Digital Visual Interface): The digital display interface standard set by the DDWG in 1999.

HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s

designed to protect video content and requires a HDCP-compatible device to display the encrypted video.

DDWG (Digital Display Working Group): Lead by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this

open industry group’s objective is to address the industry’s requirements for a digital connectivity specification for high-performance

PCs and digital displays.

Note

• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can be connected by

using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need to make a separate connection for

audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported.

• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or

there’s no sound from a component connected via HDMI, check its setup. Refer to the connected component’s instruction manual for

details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using an RIHD-compatible TV, Player, or Recorder

p, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo

components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over

HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, opera-

tion with components other than p-compatible components cannot be guaranteed.

■ About p-compatible components

■ Operations that can be performed with p

connection

The following components are p-compatible. (As

of February 2010) See the Onkyo web site for latest infor-

mation.

For p-compatible TV

The following linked operation is possible by connecting

the AV receiver to an p-compatible TV.

• The AV receiver will enter Standby mode when the

power of the TV is turned to Standby.

• You can set on the menu screen of the TV to either out-

put the audio from the speakers connected to the AV

receiver, or from the speakers of the TV.

• Panasonic VIERA Link compatible TV

• Toshiba REGZA-LINK compatible TV

• Sharp TV (See Onkyo web site for latest information on

compatible models.)

Players/Recorders

• It is possible to output the video/audio from the antenna

or from the input jack of the TV from the speakers con-

nected to the AV receiver. (A connection such as optical

digital cable or similar is required above the HDMI

cable.)

• Onkyo and Integra p-compatible players

• Panasonic VIERA Link compatible players and record-

ers (only when used together with Panasonic VIERA

Link compatible TV)

• Toshiba REGZA-LINK compatible players and record-

ers (only when used together with Toshiba REGZA-

LINK compatible TV)

• Input to the AV receiver can be selected with the remote

controller of the TV.

• Operations such as volume adjustment or similar for the

AV receiver can be performed from the remote controller

of the TV.

• Sharp players and recorders (only when used together

with Sharp TV)

For p-compatible players/recorders

Models other than those mentioned above may have some

interoperability if compatible with CEC which is part of the

HDMI Standard, but operation cannot be guaranteed.

The following link operation is possible by connecting the

AV receiver to an p-compatible player/recorder.

• When the playback is started on the player/recorder,

input of the AV receiver will switch to the HDMI input

of the player/recorder that is playing back.

Note

• Do not connect the p-compatible component more than

the following number to the HDMI input terminal so that the

linked operations work properly.

• Operation of the player/recorder is possible with the

remote controller supplied with the AV receiver.

–Blu-ray Disc/DVD player is up to three.

–Blu-ray Disc recorder/DVD recorder/Digital Video Recorder is

up to three.

Not all functions may operate depending on the model.

–Cable/Satellite Set-top box is up to four.

• Do not connect the AV receiver to the other AV receiver/AV

amplifier via HDMI.

• When the p-compatible component more than the

above-mentioned is connected, the linked operations are not

guaranteed.

Download from Www.Somanuals.com. All Manuals Search And Download.

■ How to connect and setup

Confirm the settings.

1. Turn on the power for all connected components.

2. Turn off the power of the TV, and confirm that

the power of the connected components is turned

off automatically with the link operation.

3. Turn on the power of the Blu-ray Disc/DVD

player/recorder.

Confirm the connecting and setting.

1. Connect the HDMI OUT jack to the HDMI input

jack of the TV.

Blu-ray Disc/DVD player, etc.

4. Start playback of the Blu-ray Disc/DVD player/

recorder, and confirm the following.

HDMI

connection

• The power of the AV receiver is turned on

automatically, and input with the Blu-ray Disc/

DVD player/recorder connected is selected.

• The power of the TV is turned on automati-

cally, and input with the AV receiver con-

nected is selected.

AV receiver

DIGITAL AUDIO

connection

HDMI

connection

(OPTICAL)

5. Following the operating instructions of the TV,

select “Use the TV speakers” from the menu

screen of the TV, and confirm that the audio is

output from the speakers of the TV, and not from

the speakers connected to the AV receiver.

6. Select “Use the speakers connected from the AV

receiver” from the menu screen of the TV, and

confirm that the audio is output from the speak-

ers connected to the AV receiver, and not from

the TV speakers.

TV, projector, etc.

2. Connect the audio output from the TV to the

OPTICAL IN 2 jack of the AV receiver using an

optical digital cable.

Note

• When the audio return channel (ARC) function is used

with TV for HDMI 1.4, it should not be this connection

(➔ 36).

Note

3. Connect the HDMI output of the Blu-ray Disc/

• Perform the above operations when you initially use the

AV receiver, when the settings of each component are

changed, when the main power of each component is

turned off, when the power cable is disconnected from the

power supply, or when there has been a power outage.

DVD player/recorder to the HDMI IN 1 jack of

the AV receiver.

Note

• It is necessary to assign the HDMI input when connecting

the Blu-ray Disc/DVD player/recorder to other jacks

(➔ 31). Do not assign the components connected to the

HDMI IN to the TV/CD input at this time. Appropriate

CEC (Consumer Electronics Control) operation can not be

guaranteed.

Operate with the remote controller.

For buttons that can be operated (➔ 44).

Note

• Audio from DVD-Audio or Super Audio CD may not out-

put from the TV speakers. You will be able to output the

audio from the TV speakers by setting the audio output of

the DVD player to 2ch PCM. (It may not be possible

depending on the player models.)

• Even if you set to output audio on the TV speakers, audio

will be output from the speakers connected to the AV

receiver when you adjust the volume or switch the input

on the AV receiver. To output audio from the TV speakers,

re-do the operations on the TV.

Each of the “HDMI Setup” is changed to the fol-

lowing setting.

• HDMI Control (RIHD): On

• Audio Return Ch (ARC): Auto

• Power Control: On

• TV Control: On

See for details of each setting (➔ 36, 37).

• Do not connect the u cable when connecting to the u

and u audio control compatible components.

• When you select anything other than the HDMI jack

where the AV receiver is connected as the input on the TV,

input on the AV receiver will be switched to “TV/CD”.

• The AV receiver will automatically power on in conjunc-

tion when it determines it to be necessary. Even if the AV

receiver is connected to an p compatible TV or

player/recorder, it will not power on if it is not necessary.

It may not power on in conjunction when the TV is set to

output audio from the TV.

• Linked functions with the AV receiver may not work

depending on the model. Operate the AV receiver directly

in such cases.

Download from Www.Somanuals.com. All Manuals Search And Download.

Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163

ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

ONKYO EUROPE ELECTRONICS GmbH

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/

ONKYO EUROPE ELECTRONICS GmbH (UK BRANCH)

The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK

Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700

ONKYO CHINA LIMITED

Unit 1 & 12, 9/F, Tower 1, Ever Gain Plaza, 88, Container Port Road, Kwai Chung,

N.T., Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039

http://www.ch.onkyo.com/

Y1001-1

SN 29400204

* 2 9 4 0 0 2 0 4 *

Download from Www.Somanuals.com. All Manuals Search And Download.

Miele Vacuum Cleaner S185 User Manual
Napco Security Technologies Home Security System GEM K1CA User Manual
NETGEAR Network Router N750 User Manual
Nikon Camera Lens 2179B User Manual
Nuvo Stereo Amplifier LSA40 User Manual
Omega Engineering Thermometer DP95 User Manual
Omnimount Projector Accessories PMD1 User Manual
Oregon Chainsaw 91P Famp;B A107038 User Manual
Oster Blender 6640 User Manual
Panasonic Flat Panel Television BT LH1710E User Manual