SKS-HT230_En.fm Page 1 Friday, January 16, 2004 4:54 PM
Contents
Getting Started
5.1 Ch Home Theater Speaker Package
Important Safeguards..................... 2
Precautions ..................................... 3
Introduction ..................................... 4
Package Contents........................... 4
SKS-HT230
Getting to knowYour Speaker
Package ........................................ 5
SKW-150X POWERED SUBWOOFER
SKF-230F FRONT SPEAKER
Installing & Using
SKC-230C CENTER SPEAKER
SKM-230S SURROUND SPEAKER
Various Mounting Methods ............ 6
Connecting the Speakers............... 8
About Home Theater....................... 9
Adjustment .................................... 10
Instruction Manual
Appendix
Caring forYour Speakers.............. 10
Troubleshooting............................ 11
Specifications................................ 12
Thank you for purchasing an Onkyo home theater
speaker package. Please read this manual thoroughly
before using your new speakers. Following the
instructions in this manual will enable you to obtain
optimum performance and listening enjoyment from
your speaker package.
Please retain this manual for future reference.
En
Download from Www.Somanuals.com. All Manuals Search And Download.
SKS-HT230_En.fm Page 3 Friday, January 16, 2004 4:54 PM
Precautions
Important Safeguards—Continued
1. Mounting
18. Damage Requiring Service – Unplug the appli-
ance form the wall outlet and refer servicing to
qualified service personnel under the following con-
ditions:
Mount the speakers as explained in this manual. Don’t
use the front speakers without their bases as damage or
injury may result.
Use commercially available speaker mounts and brack-
ets to mount the surround speakers on a wall.
2. AC Fuse
The fuse is located inside the chassis and is not userser-
viceable. If power does not come on, contact your Onkyo
authorized service station.
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen
into the appliance,
C. If the appliance has been exposed to rain or
water,
D. If the appliance does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the appliance to its normal operation,
E. If the appliance has been dropped or damaged in
any way, and
3. Care
From time to time you should wipe off the front and rear
panels and the cabinet with a soft cloth. For heavier dirt,
dampen a soft cloth in a weak solution of mild detergent
and water, wring it out dry, and wipe off the dirt. Follow-
ing this, dry immediately with a clean cloth. Do not use
rough material, thinners, alcohol or other chemical sol-
vents or cloths since these may damage the finish or
remove the panel lettering.
F. When the appliance exhibits a distinct change in
performance – this indicates a need for service.
19. Replacement Parts – When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, elec-
tric shock, or other hazards.
20. Safety Check – Upon completion of any service or
repairs to the appliance, ask the service technician to
perform safety checks to determine that the appliance
is in proper operation condition.
21. Wall or Ceiling Mounting – The appliance should
be mounted to a wall or ceiling only as recom-
mended by the manufacturer.
22. Heat – The appliance should be situated away from
heat sources such as radiators, heat registers, stoves,
or other appliances (including amplifiers) that pro-
duce heat.
Use a vacuum cleaner to remove dust from hard-to-reach
grilles.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
The voltage of the available power supply differs
according to country or region. Be sure that the power
supply voltage of the area where this unit will be used
meets the required voltage (e.g., AC 230 V, 50 Hz) writ-
ten on the rear panel.
23. Liquid Hazards – The appliance should not be
exposed to dripping or splashing and no objects
filled with liquids, such as vases should be placed
on the appliance.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SKS-HT230_En.fm Page 4 Friday, January 16, 2004 4:54 PM
Introduction
The SKS-HT230’s stylish enclosures are made of aluminum and their slim design makes them ideal for use with LCD
and plasma TVs.
SKS-HT230
The SKS-HT230 is a 5.1-channel speaker package consisting of front left and right speakers, a center speaker, surround
left and right speakers, and a powered subwoofer. Simply connect the speakers to your AV amp or receiver for superb
surround sound playback.
Speaker terminals and speaker cables are color-coded for easy identification. Simply connect each speaker cable to the
same-colored speaker terminals.
Package Contents
Make sure your box contains all of the items below. If anything is missing, contact the nearest Onkyo dealer.
• Front speakers
(SKF-230F)
• Speaker cable for front speakers
(4.5 m)
• Spacers for wall mounting [×20]
(Red)
(White)
• Cork spacers [×4]
(For the subwoofer)
• Front speaker bases
• Front speaker base fixing screws [×8]
• Center speaker
(SKC-230C)
• Speaker cable for center speaker
(3 m)
• Center speaker base
(Green)
• Surround speakers
(SKM-230S)
• Speaker cables for surround
speakers (9 m)
• Subwoofer
(SKW-150X)
• RCA cable for subwoofer
connection
(Blue)
(Gray)
SKW-150
X
P
O
W
E
R
D
S
U
B
W
O
O
F
E
R
The alphabet displayed at the end of the product name found in catalogs and on package represents the color of
SKS-HT230. Though the color varies, the specifications and operations are the same.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SKS-HT230_En.fm Page 5 Friday, January 16, 2004 4:54 PM
Getting to knowYour Speaker Package
Subwoofer (SKW-150X)
Front, Center & Surround Speakers
(SKF-230F, SKC-230C, SKM-230S)
■ Front
3
2
1
-
SKW 150
X
POWERD SUBWOOFER
■ Rear
4
POWERED SUBWOOFER
-
MODEL NO. SKW 150
X
OUTPUT
LEVEL
LINE
INPUT
1Speaker terminals
MIN
MAX
POWER
:
RED STANDBY
GREEN ON
These push terminals are for connecting the speaker
to your DVD Receiver, amp, or other receiver with
the supplied speaker cables. The supplied speaker
cables are color-coded for easy identification. Sim-
ply connect each cable to the same-colored positive
speaker terminal.
:
ON
OFF
2
3
1
To AC outlet
2Keyhole slots
A POWER switch and indicator
These keyhole slots can be used to wall-mount the
speaker either horizontally or vertically.
To turn on the SKW-150X, set the POWER switch
to the ON position (the indicator lights up).
To turn off the SKW-150X, set the POWER switch
to the OFF position (the indicator goes out).
Red: The unit is in standby mode
3Speaker mount/bracket inserts
These threaded inserts can be used to attach the
speaker either horizontally or vertically to a speaker
mount or bracket.
Green: The unit is in operation mode
Note:
The SKW-150X automatically turns to Standby
mode when no signal has been input for about 20
minutes. The SKW-150X automatically turns on
when an input signal is detected in Standby mode.
Use commercially available M5 screws to attach the
speaker to a speaker mount or bracket.
4Base inserts (other than center speaker)
These threaded inserts can be used to mount the
speaker on the supplied base (screws included).
B OUTPUT LEVEL control
This control is used to adjust the output level of the
subwoofer.
C LINE INPUT
The RCA input should be connected to the sub-
woofer preout on your AV receiver, amp, or other
receiver with supplied RCA cable.
Note:
TheAuto Standby function turns the subwoofer on when
the input signal exceeds a certain level. If the Auto
Standby function does not work reliably, try slightly
increasing or decreasing the subwoofer output level on
your receiver or amp.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SKS-HT230_En.fm Page 6 Friday, January 16, 2004 4:54 PM
Various Mounting Methods
Front Speaker Bases
Wall Mounting
If you intend to stand the front speakers on the floor or
on a TV stand or AV stand, you should attach the sup-
plied front speaker bases. To do this, align the mounting
holes in the base with base inserts on the front speaker’s
rear panel, and secure by using four of the supplied fix-
ing screws.
The front speakers, center speaker or surround speakers
can easily be wall mounted by using the keyhole slots. To
prevent the speaker from vibrating against the wall,
attach four of the supplied spacers to the keyhole fins on
the rear of each speaker.
■ Mounting vertically
To mount the front speakers or surround speakers verti-
cally, use the keyhole slot shown to hang each speaker on
a screw that’s securely screwed into the wall.
Front/Surround speakers
65 mm 65 mm
Keyhole slot for
vertical wall
45 mm
mounting
Base inserts
Spacers
Front speaker base
Spacers
Mounting holes
Bottom
Center Speaker Base
The center speaker base is for mounting the center
speaker horizontally. If you put it on a TV stand or AV
stand, aim it toward the listening position. The center
speaker should sit securely on the base. If it’s loose, try
resetting it.
Note:
• If you put the center speaker on the floor, take it off the
base and position it so that it’s facing slightly up
toward the listener’s ears.
Baseforhorizontal
mounting
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SKS-HT230_En.fm Page 7 Friday, January 16, 2004 4:54 PM
Various Mounting Methods—Continued
■ Mounting horizontally
Using Speaker Mounts/Brackets
To mount the center speaker horizontally, use the two
keyhole slots shown to hang each speaker on two screws
that are securely screwed into the wall.
Threaded inserts for M5 screws are provided on the rear
of each speaker for wall-mounting with commercially
available speaker mounts and brackets. Refer to the man-
ual supplied with your mounts or brackets for installa-
tion details.
Center speaker
Keyhole slots for horizontal
wall mounting
Spacers
Spacers
Use this hole if mounting
vertically
65 mm
65 mm
Use this hole if mounting
horizontally
75 mm
190 mm
75 mm
Caution:
A mounting screw’s ability to support a speaker depends
on how well it’s anchored to the wall. If you have hollow
walls, screw each mounting screw into a stud. If there are
no studs, or the walls are solid, use suitable wall anchors.
Use screws with a head diameter of 9.5 mm or less and a
shank diameter of 4 mm or less. With hollow walls, use
a cable/pipe detector to check for any power cables or
water pipes before making any holes.
Note:
The portion of the screw that goes into the speaker’s
threaded insert should be between 5 mm and 9 mm long,
as shown.
Mount or bracket
Leave a gap of between 7 mm and 10 mm between the
wall and the base of the screw head, as shown.
5 mm
Wall
5 mm–9 mm
Using the supplied cork spacers
■ Using cork spacers with the subwoofer
(SKW-150X)
We recommend using the supplied cork spacers to
achieve the best possible sound from your speaker. The
cork spacers prevent the speaker from moving, providing
a more stable setup.
7 mm–10 mm
(We recommend that you consult a home installation
professional.)
Cork spacers
Bottom of the
SKW-150X
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SKS-HT230_En.fm Page 8 Friday, January 16, 2004 4:54 PM
Connecting the Speakers
Read the following before connecting your speakers:
• Turn off your amp before making any connections.
Connecting the Subwoofer
• The nominal impedance of these speakers is 8 Ω. Use
Using the supplied RCA cable, connect
the subwoofer’s LINE INPUT to your amp’s
SUBWOOFER PREOUT.
1
only an amp that supports this impedance.
• Pay close attention to speaker wiring polarity. Connect
positive (+) terminals to only positive (+) terminals,
and negative (–) terminals to only negative (–) termi-
nals. If the speakers are wired incorrectly, the sound
will be out of phase and will sound unnatural.
SKS-HT230 & 5-channel AV Amp Hookup
• Be careful not to short the posi-
tive and negative wires. Doing so
may damage your amp.
Onkyo AV receiver used in this example.
Front right
speaker
Front left
speaker
Center
speaker
Red
Green
White
Connecting the Speaker Cables
SURROUND
SPEAKERS
FRONT SPEAKERS
R
L
R
CENTER
L
Use the cables to connect each speaker’s
1
input terminals to the corresponding
speaker output terminals on your amp.
To make a connection, while
pressing the terminal lever,
Surround
right speaker
Surround
left speaker
insert the wire into the hole, and
then release the lever.
Make sure that the terminals are
gripping the bare wires, not the insulation.
Gray
Blue
L
SURROUND
SPEAKERS
ANTENNA
FRONT SPEAKERS
CENTER
PREOUT
AUDIO
AC INLET
R
L
R
L
REMOTE
ANTENNA
CONTROL
R
AM
FM 75
IN
OUT
MD/CDR/TAPE
IN
SUB
WOOFER TV/LINE
DIGITAL
VIDEO OUTPUT
Y
PB
PR
OPTICAL
OUT
IN
S
VIDEO
VIDEO
COMPONENT
PREOUT
AUDIO
LINE
INPUT
SUB
WOOFER
Powered
subwoofer
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SKS-HT230_En.fm Page 9 Friday, January 16, 2004 4:54 PM
About Home Theater
Enjoying Home Theater
The SKS-HT230’s great sound means that you can enjoy surround sound with a real sense of movement in your own
home—just like being in a movie theater or concert hall.
Front left and right speakers
These output the overall sound.Their role in a home theater
is to provide a solid anchor for the sound image.They should
be positioned facing the listener at about ear level, and equi-
distant from the TV. Angle them inward so as to create a
triangle, with the listener at the apex.
Center speaker
This speaker enhances the front left and right
speakers, making sound movements distinct and
providing a full sound image. In movies it’s used
mainly for dialog.
Position it close to your TV facing forward at
about ear level, or at the same height as the front
left and right speakers.
Right
Subwoofer
The subwoofer handles the bass
sounds of the LFE (Low-Fre-
quency Effects) channel. The vol-
ume and quality of the bass output
from your subwoofer will depend
Left
on its position, the shape of your
listening room, and your listening
position. In general, a good bass
sound can be obtained by install-
ing the subwoofer in a front cor-
ner, or at one-third the width of the
wall, as shown.
Surround left and right speakers
These speakers are used for precise
sound positioning and to add realistic
ambience. Position them at the sides
of the listener, or slightly behind,
about 60–100 cm above ear level.
Ideally they should be equidistant
from the listener.
Corner
1/3 room
length
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SKS-HT230_En.fm Page 10 Friday, January 16, 2004 4:54 PM
Adjustment
Caring forYour Speakers
Placement
Setting the Subwoofer Level
• The speaker cabinets are made out of aluminum and
are therefore sensitive to extreme temperatures and
humidity, do not put them in locations subject to direct
sunlight or in humid places, such as near an air condi-
tioner, humidifier, bathroom, or kitchen.
To set the level of the subwoofer, use the OUTPUT
LEVEL control. Set it so that bass sounds are evenly bal-
anced with the treble sounds from the other speakers.
Because our ears are less sensitive to very low bass
sounds, there’s a temptation to set the level of the sub-
woofer too high. As a rule of thumb, set the subwoofer
level to what you think is the optimal level, and then back
it off slightly.
• Do not put water or other liquids close to the speakers.
If liquid is spilled over the speakers, the drive units
may be damaged.
• As explained in this manual, mount the speakers on a
wall, on the supplied bases, otherwise, they may fall,
causing personal injury or damage to the speakers.
OUTPUT
LEVEL
• Use commercially available speaker mounts and
brackets to mount the surround speakers on a wall.
• Speakers with bases should only be placed on sturdy,
flat surfaces that are free from vibration. Putting them
on uneven or unstable surfaces, where they may fall
and cause damage, will affect the sound quality.
MAX
MIN
Subwoofer Level Set OK
Using Close to a TV or Computer
TVs and computer monitors are magnetically sensitive
devices and as such are likely to suffer discoloration or
picture distortion when conventional speakers are placed
nearby. To prevent this, the SKS-HT230 speakers feature
internal magnetic shielding. In some situations, however,
discoloration may still be an issue, in which case you
should turn off your TV or monitor, wait 15 to 30 minutes,
and then turn it back on again. This normally activates the
degaussing function, which neutralizes the magnetic
field, thereby removing any discoloration effects. If dis-
coloration problems persist, try moving the speakers
away from your TV or monitor. Note that discoloration
can also be caused by a magnet or demagnetizing tool
that’s too close to your TV or monitor.
Overall response
Repsonse of other speakers
Subwoofer response
Level
Frequency
Subwoofer Level Set Incorrectly
Subwoofer level too high
The SKS-HT230 speakers contain strong magnets, so do
not put magnetic or iron objects such as screwdrivers
close to them. If you do, the object may be attracted to
the magnets, causing personal injury or damage to a
speaker cone.
Level
Subwoofer level too low
Operating Precautions
The SKS-HT230 speakers can handle the specified input
power when used for normal music reproduction. If any
of the following signals are fed to them, even if the input
power is within the specified rating, excessive current
may flow in the speaker coils, causing burning or wire
breakage:
Frequency
1. Interstation noise from an untuned FM radio.
2. Sound from fast-forwarding a cassette tape.
3. High-pitched sounds generated by an oscillator, elec-
tronic musical instrument, and so on.
4. Amplifier oscillation.
5. Special test tones from audio test CDs and so on.
6. Thumps and clicks caused by connecting or discon-
necting audio cables (Always turn off your amplifier
before connecting or disconnecting cables.)
7. Microphone feedback.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SKS-HT230_En.fm Page 11 Friday, January 16, 2004 4:54 PM
Troubleshooting
Symptom
Possible cause
Remedy
The speaker cables are not connected properly. Check the speaker cables and correct as necessary.
On the amp or receiver, the Speaker Configu- Check the Speaker Configuration settings and
There’s no sound coming
from certain speakers?
ration settings for those speakers are set to
make sure that the speakers are set to something
either None or No. Or, the number of speaker other than None or No. Or set the number of
channels is not set to 5ch.
speaker channels to 5ch.
The subwoofer does not
turn on?
The power plug is not fully inserted into the
wall outlet.
Insert the power plug fully into the wall outlet.
The OUTPUT LEVEL control is set to mini-
mum.
Turn up the OUTPUT LEVEL control.
The RCA cable is not properly connected to
the subwoofer’s LINE INPUT.
Make sure that the RCA cable is properly con-
nected to the subwoofer’s LINE INPUT.
The subwoofer produces
no sound?
The level of the input signal was too low and
the subwoofer entered Standby mode.
Slightly increase the subwoofer preout output level
on your amp.
On your amp or receiver, the speaker setting is Check the settings on your amp or receiver.
set to Subwoofer No, or the subwoofer mode is
set to Subwoofer Off.
The subwoofer produces
hardly any sound?
The source material contain little or no bass
content.
Choose source material with more bass content.
The RCA cable is not properly connected to
the subwoofer’s LINE INPUT.
Make sure that the RCA cable is properly con-
nected to the subwoofer’s LINE INPUT.
A humming sound can be
heard from the sub-
woofer?
External interference from a TV or other elec- Move the subwoofer and RCA cable away from the
tronic device is being picked up.
interference source. Make sure your audio system
is grounded properly.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SKS-HT230_En.fm Page 12 Friday, January 16, 2004 4:54 PM
Specifications
■ Powered Subwoofer (SKW-150X)
■ Center Speaker (SKC-230C)
Type:
Bass reflex with built-in
power amplifier
Input sensitivity/impedance: 220 mV / 15 kΩ
Type:
2-way bass reflex center
speaker
Impedance:
8 Ω
Maximum output power:
Frequency response:
Cabinet capacity:
Dimensions (W × H × D): 235 × 518 × 411 mm
Weight:
150 W Dynamic
30 Hz–150 Hz
32.5 L
Maximum input power:
Output sound pressure level: 80 dB/W/m
Frequency response:
Crossover frequency:
Cabinet capacity:
100 W
65 Hz–35 kHz
6.5 kHz
2 L
12.6 kg
Drive unit:
Power supply:
Australia:
Others:
Power consumption:
Other:
20 cm cone woofer
Dimensions (W × H × D): 340 × 130 × 91 mm
Weight:
1.6 kg
AC 230–240 V, 50 Hz
AC 220–230 V, 50/60 Hz
77 W
Speaker:
8 cm cone woofer
2.5 cm balanced-dome
tweeter
Other:
Magnetic shielding
Auto Standby function
■ Surround Speaker (SKM-230S)
■ Front Speaker (SKF-230F)
Type:
2-way bass reflex
Type:
2-way bass reflex front
surround speaker
speaker
Impedance:
Maximum input power:
8 Ω
100 W
Impedance:
Maximum input power:
8 Ω
100 W
Output sound pressure level: 80 dB/W/m
Output sound pressure level: 80 dB/W/m
Frequency response:
Crossover frequency:
Cabinet capacity:
65 Hz–35 kHz
6.5 kHz
2 L
Frequency response:
Crossover frequency:
Cabinet capacity:
65 Hz–35 kHz
6.5 kHz
2 L
Dimensions (W × H × D): 130 × 340 × 91 mm
Dimensions (W × H × D): 130 × 340 × 91 mm
Weight:
1.6 kg
Weight:
1.6 kg
Speaker:
8 cm cone woofer
2.5 cm balanced-dome
tweeter
Drive unit:
8 cm cone woofer
2.5 cm balanced-dome
tweeter
Other:
Magnetic shielding
Other:
Magnetic shielding
Specifications and appearance are subject to change
without prior notice.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
HOMEPAGE
SN 29343713
I0401-1
(C) Copyright 2004 ONKYO CORPORATION Japan. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|